Parkside 3901227974 Operating And Safety Instructions Manual

Tip
Operating And Safety Instructions Manual

Acest manual este potrivit și pentru

IAN 331932_1907
SLIDING COMPOUND MITRE SAW PZKS 2000 B2
CHAT
KAPP- UND ZUGSÄGE
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
DE
CY
SLIDING COMPOUND MITRE SAW
Operating and Safety Instructions
Translation of Original Operating Manual
GB
НАСТОЛЕН ЦИРКУЛЯР
Инструкции за обслужване и безопасност
Превод на оригиналното ръководство за експлоатация
BG
PREKLOPNA I POTEZNA TESTERA
Napomene za rukovanje i sigurnosne napomene
Originalno uputstvo za upotrebu
RS
FERĂSTRĂU DE RETEZAT ȘI FERĂSTRĂU JOAGĂR
Instrucţiuni de utilizare şi de siguranţă
Traducerea instrucţiunilor de utilizare originale
RO
POTEZNO-NAGIBNA PILA
Upute za posluživanje i za Vašu sigurnost
Prijevod originalnih uputa za uporabu
HR
ΦΑΛΤΣΟΠΡΊΟΝΟ
Οδηγίες χειρισµού και ασφαλείας
Μετάφραση του πρωτοτύπου των οδηγιών χρήσης
GR CY
7
GB / CY Operating and Safety Instructions Page 01
HR Upute za posluživanje i za Vašu sigurnost Stranica 15
RS Napomene za rukovanje i sigurnosne napomene Strana 29
RO Instrucţiuni de utilizare şi de siguranţă Pagina 45
BG Инструкции за обслужване и безопасност страница 60
GR / CY Οδηγίες χειρισµού και ασφαλείας Σελίδα 77
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 93
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.
GB CY
Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции на уреда.
BG
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα µε τις εικόνες και εξοικειωθείτε µε όλες τις λειτουργίες της συσκευής.
GR CY
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.
DE AT CH
Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama uraja.
HR
Pre nego što počnete sa čitanjem preklopite stranicu sa slikama, i upoznajte se sa svim funkcijama uređaja.
RS
Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.
RO
2
4
3
5
24
25
23
23
11
35
27a
26a
20
27
22
26
36
D
1
1
10
2
4
5
7
12131415
17
7
11
8
9
35
16b
8
37
22
16a
21
22
1918
3
6
24
7a7a
24a
16
32
38
2
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A A
B B
C C
D D
E E
F F
G G
H H
I I
J J
K K
L L
IAN 331932_1907
Kapp- und Zugsäge
Mitre saw
Scie à onglet mixtes
220 - 240 V
~
50 Hz | 4800 min
-1
S1 1700 W / S6 25% 2000 W
Ø 210 mm x Ø 30 mm x 2.6 mm
manufactured: 07/2019
S.Nr.:
PZKS 2000 B2
10
6 7
13
988
14
11
12
!
1918
14
6
1
14
2
6
4
16a
3
A
max. 8 mm
4
6
B
4
4
7
7
14
14
14
24
24a
5a
7
max. 8 mm
7
13
14
C
22
26
20
C
27
22
20
max. 8 mm
25
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A A
B B
C C
D D
E E
F F
G G
H H
I I
J J
K K
L L
IAN 331932_1907
Kapp- und Zugsäge
Mitre saw
Scie à onglet mixtes
220 - 240 V
~
50 Hz | 4800 min
-1
S1 1700 W / S6 25% 2000 W
Ø 210 mm x Ø 30 mm x 2.6 mm
manufactured: 07/2019
S.Nr.:
PZKS 2000 B2
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A A
B B
C C
D D
E E
F F
G G
H H
I I
J J
K K
L L
IAN 331932_1907
Kapp- und Zugsäge
Mitre saw
Scie à onglet mixtes
220 - 240 V
~
50 Hz | 4800 min
-1
S1 1700 W / S6 25% 2000 W
Ø 210 mm x Ø 30 mm x 2.6 mm
manufactured: 07/2019
S.Nr.:
PZKS 2000 B2
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A A
B B
C C
D D
E E
F F
G G
H H
I I
J J
K K
L L
16
17 18
19
15
20
21 22
5
29
34
31
33
30
28
C
6
17
32
32a
32b
E
E
E
32b
DRÜCKEN
PUSH
C
1GB/CY
Table of contents: Page:
1. Explanation of the symbols on the equipment ..................................................................................................................................................2
2. Introduction ..........................................................................................................................................................................................................3
3. Device description (fig. 1-22) .............................................................................................................................................................................3
4. Scope of delivery ................................................................................................................................................................................................4
5. Intended use ........................................................................................................................................................................................................ 4
6. Safety information ............................................................................................................................................................................................... 4
7. Technical data ..................................................................................................................................................................................................... 7
8. Before starting the equipment ............................................................................................................................................................................8
9. Attachment ...........................................................................................................................................................................................................8
10. Operation ............................................................................................................................................................................................................ 9
11. Maintenance .....................................................................................................................................................................................................10
12. Transport ............................................................................................................................................................................................................11
13. Storage ..............................................................................................................................................................................................................11
14. Electrical connection .........................................................................................................................................................................................11
15. Disposal and recycling .....................................................................................................................................................................................12
16. Troubleshooting .................................................................................................................................................................................................13
17. Warranty certificate ..........................................................................................................................................................................................14
18. Declaration of conformity .............................................................................................................................................................................. 108
2 GB/CY
1. Explanation of the symbols on the equipment
GB
CY
Before commissioning, read and observe the operating instructions and safety instructions!
GB
CY
Wear safety goggles!
GB
CY
Wear ear-muffs!
GB
CY
Wear a breathing mask!
GB
CY
Important! Risk of injury. Never reach into the running saw blade!
GB
CY
Important! Laser radiation
GB
CY
Protection Class II (double shielded)
3GB/CY
2. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
Improper handling,
Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service techni-
cians,
Installation and replacement of non-original spare parts,
Application other than specified,
A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
3. Device description (fig. 1-22)
1. Handle
2. ON/OFF switch
3. Lock switch
4. Machine head
5. Moving saw blade guard
5a. Locking screw
6. Saw blade
7. Clamping device
7a. Star-grip screw
8. Workpiece support
9. Set screw for workpiece support
10. Table insert
11. Handle / Set screw for rotary table
12. Pointer
13. Scale
14. Rotary table
15. Fixed saw table
16. Stop rail
16a. Movable stop rail
16b. Set screw
17. Sawdust bag
18. Angle screw
19. Angle indicator
20. Set screw for drag guide
21. Drag guide
22. Set screw
23. Locking bolt
24. Screw for cutting depth limiting
24a. Knurled nut for cutting depth limiting
25. Stop for cutting depth limiting
26. Adjusting screw (90°)
26a. Lock nut (90°)
27. Adjusting screw (45°)
27a. Lock nut (45°)
28. Flange screw
29. Outer flange
30. Saw shaft lock
31. Inner flange
32. Laser
32a. Laser housing cover
32b. Philips screw
33. ON/OFF switch laser
34. Guide bracket
35. Latched position lever
36. Tilt protection
37. Length stop
38. Adjustment screw
A.) 90° stop angle (not supplied)
B.) 45° stop angle (not supplied)
C.) Allen key, 6 mm
D.) Allen key, 3 mm
E.) Philips head screw (Laser)
4 GB/CY
4. Scope of delivery
Crosscut, drag and mitre saw
2 x Clamping device (7)
2 x Workpiece support (8) (preassembled)
Sawdust bag (17)
Allen key 6 mm (C)
Allen key 3 mm (D)
Operating manual
5. Intended use
The crosscut, drag and mitre saw is designed to crosscut wood
and plastic respective of the machine’s size. The saw is not de-
signed for cutting firewood.
Warning!
Do not use the saw to cut materials other than those specified
described in manual.
Warning!
The supplied saw blade is only intended for the sawing of
wood! Do not use this blade for the sawing of firewood!
The equipment is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user / op-
erator and not the manufacturer will be liable for any damage
or injuries of any kind caused as a result of this.
The equipment is to be operated only with suitable saw blades.
It is prohibited to use any type of cutting-off wheel.
To use the equipment properly you must also observe the safety
information, the assembly instructions and the operating instruc-
tions to be found in this manual.
All persons who use and service the equipment have to be
acquainted with this manual and must be informed about the
equipment’s potential hazards.
It is also imperative to observe the accident prevention regula-
tions in force in your area.
The same applies for the general rules of health and safety at
work.
The manufacturer will not be liable for any changes made to the
equipment nor for any damage resulting from such changes.
Even when the equipment is used as prescribed it is still im-
possible to eliminate certain residual risk factors. The following
hazards may arise in connection with the machine’s construc-
tion and design:
Contact with the saw blade in the uncovered saw zone.
Reaching into the running saw blade (cut injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw blade.
Damage to hearing if ear-muffs are not used as necessary.
Harmful emissions of wood dust when used in closed rooms.
Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty
will be voided if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
6. Safety information
General power tool safety warnings
m WARNING! Read all safety warnings, instruc-
tions, illustrations and specifications provided with
this power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term “power tool” in the warnings refers to your mains-operat-
ed (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive at-
mospheres, such as in the presence of flamma-
ble liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while op-
erating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce
risk of electric shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the
risk of electric shock.
3. Personal safety
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medi-
cation. A moment of inattention while operating power
tools may result in serious personal injury.
5GB/CY
Use personal protective equipment. Always
wear eye protection. Protective equipment such as
a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that
have the switch on invites accidents.
Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in
personal injury.
Do not overreach. Keep proper footing and
balance at all times. This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
4. Power tool use and care
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was de-
signed.
Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must be
repaired.
Disconnect the plug from the power source
and/or remove the battery pack, if detach-
able, from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in the
hands of untrained users.
Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly main-
tained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could result in
a hazardous situation.
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. Service
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
Safety instructions for mitre saws
a) Mitre saws are intended to cut wood or wood-
like products, they cannot be used with abrasive
cut-off wheels for cutting ferrous material such as
bars, rods, studs, etc. Abrasive dust causes moving parts
such as the lower guard to jam. Sparks from abrasive cutting
will burn the lower guard, the kerf insert and other plastic parts.
b) Use clamps to support the workpiece when-
ever possible. If supporting the workpiece by
hand, you must always keep your hand at least
100 mm from either side of the saw blade. Do
not use this saw to cut pieces that are too small
to be securely clamped or held by hand. If your
hand is placed too close to the saw blade, there is an
increased risk of injury from blade contact.
c) The workpiece must be stationary and clamped
or held against both the fence and the table.
Do not feed the workpiece into the blade or
cut “freehand” in any way. Unrestrained or moving
workpieces could be thrown at high speeds, causing injury.
d) Push the saw through the workpiece. Do not pull
the saw through the workpiece. To make a cut,
raise the saw head and pull it out over the work-
piece without cutting, start the motor, press the
saw head down and push the saw through the
workpiece. Cutting on the pull stroke is likely to cause the
saw blade to climb on top of the workpiece and violently
throw the blade assembly towards the operator.
e) Never cross your hand over the intended line
of cutting either in front or behind the saw
blade. Supporting the workpiece “cross handed” i.e.
holding the workpiece to the right of the saw blade with
your left hand or vice versa is very dangerous.
f) Do not reach behind the fence with either hand
closer than 100 mm from either side of the saw
blade, to remove wood scraps, or for any oth-
er reason while the blade is spinning. The prox-
imity of the spinning saw blade to your hand may not be
obvious and you may be seriously injured.
6 GB/CY
g) Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with
the outside bowed face toward the fence. Al-
ways make certain that there is no gap be-
tween the workpiece, fence and table along
the line of the cut. Bent or warped workpieces can
twist or shift and may cause binding on the spinning saw
blade while cutting. There should be no nails or foreign
objects in the workpiece.
h) Do not use the saw until the table is clear of all
tools, wood scraps, etc., except for the work-
piece. Small debris or loose pieces of wood or other
objects that contact the revolving blade can be thrown
with high speed.
i) Cut only one workpiece at a time. Stacked multi-
ple workpieces cannot be adequately clamped or braced
and may bind on the blade or shift during cutting.
j) Ensure the mitre saw is mounted or placed on
a level, firm work surface before use. A level and
firm work surface reduces the risk of the mitre saw becom-
ing unstable.
k) Plan your work. Every time you change the bev-
el or mitre angle setting, make sure the adjust-
able fence is set correctly to support the work-
piece and will not interfere with the blade or
the guarding system. Without turning the tool “ON”
and with no workpiece on the table, move the saw blade
through a complete simulated cut to assure there will be no
interference or danger of cutting the fence.
l) Provide adequate support such as table exten-
sions, saw horses, etc. for a workpiece that is
wider or longer than the table top. Workpieces
longer or wider than the mitre saw table can tip if not
securely supported. If the cut-off piece or workpiece tips,
it can lift the lower guard or be thrown by the spinning
blade.
m) Do not use another person as a substitute for
a table extension or as additional support. Un-
stable support for the workpiece can cause the blade to
bind or the workpiece to shift during the cutting operation
pulling you and the helper into the spinning blade.
n) The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade. If confined, i.e. using length stops, the cut-
off piece could get wedged against the blade and thrown
violently.
o) Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing. Rods have a tendency to roll while being cut,
causing the blade to “bite” and pull the work with your
hand into the blade.
p) Let the blade reach full speed before contact-
ing the workpiece. This will reduce the risk of the
workpiece being thrown.
q) If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could cause
loss of control or damage to the mitre saw.
r) After finishing the cut, release the switch, hold
the saw head down and wait for the blade to
stop before removing the cut-off piece. Reaching
with your hand near the coasting blade is dangerous.
s) Hold the handle firmly when making an incom-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion. The braking action of the saw may cause the saw
head to be suddenly pulled downward, causing a risk of
injury.
Safety Instructions for the handling of saw blades
1. Do not use damaged or deformed saw blades.
2. Do not use any insertion tools with cracks. Sort out cracked
insertion tools. Repairs are not permitted.
3. Do not use saw blades made of high speed steel.
4. Check the condition of the saw blades before using the
crosscut, drag and mitre saw.
5. Make sure that a suitable saw blade for the material to
be cut is selected.
6. Only use saw blades recommended by the manufacturer.
Saw blades designed to cut wood and similar materials
must comply with EN 847-1.
7. Do not use saw blades made of high-speed alloy steel
(HSS steel).
8. Only use saw blades for which the maximum permissible
speed is not lower than the maximum spindle speed of the
crosscut, drag and mitre saw and which are suitable for
the material to be cut.
9. Observe the saw blade direction of rotation.
10. Only insertion the saw blade if you have mastered their
use.
11. Observe the maximum speed. The maximum speed speci-
fied on the insertion tool may not be exceeded. If speci-
fied, observe the speed range.
12. Clean grease, oil and water off of the clamping surfaces.
13. Do not use any loose reducing rings or bushes for the re-
ducing of holes on saw blades.
14. Make sure that fixed reducer rings for securing the inser-
tion tool have the same diameter and have at least 1/3 of
the cutting diameter.
15. Make sure that fixed reducer rings are parallel to each
other.
16. Handle insertion tool with caution. They are ideally stored
in the originally package or special containers. Wear
protective gloves in order to improve grip and to further
reduce the risk of injury.
17. Prior to the use of insertion tools, make sure that all protec-
tive devices are properly fastened.
18. Prior to use, make sure that the insertion tool meets the
technical requirements of this electric tool and is properly
fastened.
19. Only use the supplied saw blade for cutting wood, never
for the processing of metals.
20. Only use saw blade diameters in accordance with the
markings on the saw.
21. Use additional workpiece supports, if required for work-
piece stability.
22. Workpiece support extensions must always be secured
and used during work.
7GB/CY
23. Replace table inserts when worn!
24. Avoid overheating of the saw teeth.
25. When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose. Replace
damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine. Allow
the saw blade to cool down before using the machine
again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
Do not look directly into the laser beam with unprotected
eyes.
Never look into the path of the beam.
Never point the laser beam towards reflecting surfaces and
persons or animals. Even a laser beam with a low output can
cause damage to the eyes.
Caution - methods other than those specified here can result
in dangerous radiation exposure.
Never open the laser module. Unexpected exposure to the
beam can occur.
The laser may not be replaced with a different type of laser.
Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
Residual risks can be minimised if the „Safety information“
and the „Proper use“ are observed along with the whole of
the operating instructions.
Do not load the machine unnecessarily: excessive pressure
when sawing will quickly damage the saw blade, which re-
sults in reduced output of the machine in the processing and
in cut precision.
When cutting plastic material, please always use clamps:
the parts which should be cut must always be fixed between
the clamps.
Avoid accidental starting of the machine: the operating but-
ton may not be pressed when inserting the plug in an outlet.
Use the tool that is recommended in this manual. In doing so,
your machine provides optimal performance.
Hands may never enter the processing zone when the ma-
chine is in operation.
Release the handle button and switch off the machine prior
to any operations.
Warning!
This electric tool generates an electromagnetic field during op-
eration. This field can impair active or passive medical implants
under certain conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with medical
implants consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
7. Technical data
AC motor.....................................................220 - 240 V
~
50Hz
Power S1 .....................................................................1700 Watt
Operating mode ............................................ S6 25%* 2000W
Idle speed n
0
..............................................................4800 min
-1
Carbide saw blade ...............................ø 210 x ø 30 x 2,6 mm
Number of teeth .......................................................................24
Maximum tooth width of saw blade ..................................3 mm
Swivel range .................................................. -45° / 0°/ +45°
Mitre cut .......................................................0° to 45° to the left
Saw width at 90° ................................................. 340 x 65 mm
Saw width at 45° ................................................. 240 x 65 mm
Saw width at 2 x 45°
(double mitre cut)) ................................................. 240 x 38 mm
Protection class ...................................................................II /
Weight .....................................................................ca. 12,15 kg
Laser class ................................................................................... 2
Wavelength of laser ........................................................ 650 nm
Laser output .....................................................................< 1 mW
* S6, continuous operation periodic duty. Identical duty cycles
with a period at load followed by a period at no load. Running
time 10 minutes; duty cycle is 25% of the running time.
The work piece must have a minimum height of 3
mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise
Total noise values determined in accordance with EN 62841.
Sound pressure level L
pA
....................... 96,5 dB(A)
Uncertainty K
pA
...............................................3 dB
Sound power level L
WA
........................ 109,5 dB(A)
Uncertainty K
WA
..............................................3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing
The above-mentioned noise emission values were measured in
accordance with a standardised test procedure and can be
used to compare one power tool with another.
The above-mentioned noise emission values can also be used
for the preliminary assessment of exposure.
Warning:
The noise emissions during the actual use of the power tool
may differ from the above-mentioned values depending on
the power tool being used, in particular on the type of work-
piece being processed.
8 GB/CY
Try to keep emissions as low as possible, for example by
limiting your working time. In this regard, all the operational
cycle phases must be taken into consideration (such as the
times when the tool is switched off or running idle).
8. Before starting the equipment
Open the packaging and remove the device carefully.
Remove the packaging material as well as the packaging
and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport damage.
If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
The equipment must be set up where it can stand securely.
Secure the machine on a workbench or a base frame with 4
screws (not included in delivery) using the holes on the fixed
saw table (15).
Pull out the pre-installed tilt protection (36) completely and
secure it with an Allen key (D).
Adjust the adjusting screw (38) to the level of the tabletop to
avoid wobbling of the machine.
All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
Before you connect the equipment to the power supply make
sure the data on the rating plate are dentical to the mains
data.
8.1 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental contact with
the saw blade and from chips flying around.
Check function
To do so, fold the saw downwards:
The saw blade guard must provide free access to the saw
blade without touching other parts.
When folding the saw upwards into the starting position, the
saw blade guard must cover the saw blade automatically.
9. Attachment
9.1 Attaching the crosscut, drag and mitre saw
(fig.1/2/4/5)
In order to adjust the rotary table (14), loosen the handle
(11) approximately 2 turns and pull up the latched position
lever (35) with your index finger.
Turn the rotary table (14) and pointer (12) to the desired
angle measurement on the scale (13) and use the handle
(11) to secure it.
By slightly pushing down the machine head (4) while pull-
ing out and removing the locking bolt (23) from the motor
mount, the locking bolt (23) will be secured in the top posi-
tion and the saw will be unlocked from the bottom position.
Turn the locking bolt (23) 90 degrees to secure it in the un-
locked position.
Swing the machine head (4) up.
It is possible to secure the clamping devices (7) to the left or
right on the fixed saw table (15). Insert the clamping devices
(7) in the holes on the rear side of the stop rail (16) and se-
cure it with the star grip screws (7a). For 0°- 45° mitre cuts,
the clamping device (7) must only be mounted on the right
side (see fig. 11-12).
It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
Workpiece supports (8) must always be secured and used
during work. Set the desired table size by loosening the set
screw (9). Then tighten the set screw (9) again.
9.2 Sawdust bag (fig. 1/22)
The saw is equipped with a debris bag (17) for sawdust and
chips.
Squeeze together the metal ring on the dust bag and attach it
to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper at
the bottom.
9.2.1 Connection to an external dust extractor
Connect the vacuum hose with the dust extraction spout.
The industrial vacuum cleaner must be suitable for the mate-
rial being worked.
When vacuuming dust that is especially detrimental to health
or carcinogenic, use a special vacuum cleaner.
9.3 Precision adjustment of the stop for crosscut
90° (fig. 1/2/5/6)
Tools required:
- Allen key 6 mm
- Open-ended spanner SW13 (not included in the scope of
delivery)
No stop angle included.
Lower the machine head (4) and secure it using the locking
bolt (23).
Loosen the set screw (22).
Position the angle stop (A) between the saw blade (6) and
the rotary table (14).
Loosen the lock nut (26a).
Adjust the adjusting screw (26) until the angle between the
saw blade (6) and rotary table (14) is 90°.
Tighten the lock nut (26a) again.
Subsequently check the position of the angle indicator. If
necessary loosen the pointer (19) using a Philips screwdriv-
er, set to position 0° on the angle scale (18) and re-tighten
the retaining screw.
9GB/CY
9.4 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/5/9/10)
Tools required:
- Allen key 6 mm
- Open-ended spanner SW13 (not included in the scope of
delivery)
No stop angle included.
Lower the machine head (4) and secure it using the locking
bolt (23).
Fix the rotary table (14) in the 0° position.
Attention!
For bevel cuts (inclined saw head), the moveable stop rail
(16a) must be fixed in the outer position. (Left side).
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a maxi-
mum of 8 mm.
The moveable stop rail (28) must be fixed in the inner posi-
tion. (Right side).
Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) 45° to the left.
45° - position angle stop (B) between the saw blade (6) and
rotary table (14).
Loosen the lock nut (27a) and adjust the screw (27) until the
angle between the saw blade (6) and the rotary table (14)
is precisely 45°.
Tighten the lock nut (27a) again.
Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (19) using a Philips screwdriv-
er, set to position 45° on the angle scale (18) and re-tighten
the retaining screw.
10. Operation
10.1 Using the laser (fig. 18)
To switch on: Press the ON/OFF switch laser (33) 1x. A
laser line is projected onto the material you wish to process,
providing an exact guide for the cut.
To switch off: Press again the ON/OFF switch laser (33).
10.2 Limiting the cutting depth (fig. 3/13)
The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the knurled nut (24a) on the screw
(24). Turn the screw (24) in or out to set the required cutting
depth. Then re-tighten the knurled nut (24a) on the screw
(24).
Check the setting by completing a test cut.
10.3 Serial cutting
For repeated cuts of the same length, the length stop (37) can
be opened. You can use the length stop (37) on the right and
on the left.
Fold up the length stop (37).
Loosen the set screw for workpiece support (9).
Pull out the workpiece support (8).
Set the required dimension between saw blade and length
stop (37).
Re-tighten the set screw for workpiece support (9).
Perform cutting as described in sections 10.4 to 10.7.
10.4 Crosscut 90° and turntable 0° (fig. 1/2/7)
In the case of cutting widths up to approx. 100 mm it is possible
to fix the traction function of the saw with the set screw (20) in
the rear position. In this position the machine can be operated
in cross cutting mode. If the cutting width is over 100 mm then
it is necessary to ensure that the set screw (20) is loose and the
machine head (4) can move.
Attention!
For 90° crosscuts, the moveable stop rail (16a) must be fixed
in the inner position.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
The moveable stop rail (16a) must be locked in a position far
enough from the inner position that the distance between the
stop rail (16a) and the saw blade (6) is no more than 8 mm..
Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Re-tighten the set screw (16b).
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine head (4) and
fix it in this position if required (dependent on the cutting
width).
Place the piece of wood to be cut at the stop rail (16) and
on the turntable (14).
Lock the material with the clamping devices (7) on the fixed
saw table (15) to prevent the material from moving during
the cutting operation.
Release the lock switch (3) and press the ON/OFF switch
(2) to start the motor.
With the drag guide (21) fixed in place (21):: use
the handle (1) to move the machine head (4) steadily and
with light pressure downwards until the saw blade (6) has
completely cut through the work piece.
With the drag guide (21) not fixed in place (21):
pull the machine head (4) all the way to the front. Lower the
handle (1) to the very bottom by applying steady and light
downward pressure. Now push the machine head (4) slowly
and steadily to the very back until the saw blade (6) has
completely cut through the work piece.
When the cutting operation is completed, move the machine
head back to its upper (home) position and release the ON/
OFF button (2).
Attention! The machine executes an upward stroke auto-
matically due to the return spring, i.e. do not release the han-
dle (1) after completing the cut; instead allow the machine
head to move upwards slowly whilst applying light counter
pressure.
10.5 Crosscut 90° and turntable 0° - 45°
(fig. 1/7/8)
The crosscut, drag and mitre saw can be used to make cross-
cuts of 0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
10 GB/CY
Important!
For 90° crosscuts, the moveable stop rail (16a) must be fixed
in the inner position.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Secure the set screw (16b) again.
Loosen the handle (11) if tightened, pull up the latched posi-
tion lever (35) with your index finger and use the handle
(11) to set the rotary table (14) to the desired angle.
The pointer (12) on the rotary table must match the desired
angle on the scale (13) on the fixed saw table (15).
Re-tighten the handle (11) to secure the rotary table (14).
Cut as described under section 10.5.
10.6 Mitre cut 0°- 45° and turntable 0°
(fig. 1/2/11)
The crosscut, drag and mitre saw can be used to make mitre
cuts of 0° - 45° in relation to the work face.
Attention!
For bevel cuts (inclined saw head), the moveable stop rail
(16a) must be fixed in the outer position. (Left side).
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
The moveable stop rail (28) must be fixed in the inner posi-
tion. (Right side).
Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Secure the set screw (16b) again.
Move the machine head (4) to the top position.
Fix the rotary table (14) in the 0° position.
Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) to the left, until the pointer (19) indi-
cates the desired angle measurement on the scale (18).
Re-tighten the set screw (22).
Cut as described in section 10.4.
10.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 2/4/12)
The crosscut, drag and mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
Attention!
For bevel cuts (inclined saw head), the moveable stop rail
(16a) must be fixed in the outer position. (Left side).
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Re-tighten the set screw (16b).
Move the machine head (4) to its upper position.
Release the rotary table (14) by loosening the handle (11).
Using the handle (11), set the rotary table (14) to the de-
sired angle (refer also to point 10.5 in this regard).
Re-tighten the handle (11) to secure the rotary table (14).
Undo the set screw (22).
Use the handle (1) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 10.6).
Re-tighten the set screw (22).
Cut as described under section 10.4.
11. Maintenance
m Warning! Prior to any adjustment, maintenance
or service work disconnect the mains power plug!
11.1 General maintenance measures
Wipe chips and dust off the machine from time to time using a
cloth. In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
11.2 Cleaning the moving saw blade guard safety
device (5)
Always check the saw blade guard for debris before using the
machine.
Remove old sawdust and splinters using a brush or similar tool.
11.3 Replacing the table insert
Danger!
With a damaged table insert (10) there is a risk of small parts
getting stuck between table insert and saw blade, blocking the
saw blade. Immediately replace damaged table in-
serts!
1. Remove screws at table insert. If required, turn rotary table
and incline saw head to be able to reach the screws.
2. Remove table insert.
3. Install new table insert.
4. Tighten the screws at table insert.
11.4 Brush inspection
Check the carbon brushes after the first 50 operating hours
with a new machine, or when new brushes have been fitted.
After carrying out the first check, repeat the check every 10
operating hours.
If the carbon is worn to a length of 6 mm, or if the spring or
contact wire are burned or damaged, it is necessary to replace
both brushes. If the brushes are found to be usable following
removal, it is possible to reinstall them.
When servicing the carbon brushes, open the two latches coun-
terclockwise (as shown in Figure 21). Then remove the carbon
brushes.
Replace the carbon brushes in the reverse order.
11GB/CY
11.5 Changing the saw blade (fig. 1/2/14-17)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
Swing the machine head (4) upwards and lock with the lock-
ing bolt (23).
Loosen the retaining screw (5a) of the cover using a Philips
screwdriver.
WARNING!
Do not fully remove this screw.
Fold the saw blade guard (5) upwards until the saw blade
guard (5) is above the flange screw (28).
With one hand insert the Allen key (C) in the flange screw
(28).
Hold the Allen key (C) and slowly close the saw blade guard
(5) until it touches the Allen key (C).
Firmly press the saw shaft lock (30) and slowly rotate the
flange screw (28) in clockwise direction. The saw shaft lock
(30) engages after no more than one rotation.
Now, using a little more force, slacken the flange screw (28)
in the clockwise direction.
Turn the flange screw (28) right out and remove the outer
flange (29).
Take the blade (6) off the inner flange (31) and pull out
downwards.
Carefully clean the flange screw (28), outer flange (29) and
inner flange (31).
Fit and fasten the new saw blade (6) in reverse order.
Fold the saw blade guard (5) downwards until the saw
blade guard (5) engages in the locking screw (5a).
Re-tighten the locking screw (5a).
Important!
The cutting angle of the teeth, in other words the direction of
rotation of the saw blade (6) must coincide with the direction
of the arrow on the housing.
Before continuing your work make sure that all safety de-
vices are in good working condition.
Important!
Every time that you change the saw blade (6), check to see
that it spins freely in the table insert (10) in both perpendicu-
lar and 45° angle settings.
Important!
The work to change and align the saw blade (6) must be
carried out correctly.
11.6 Adjusting the laser (fig. 19-20)
If the laser (32) ceases to indicate the correct cutting line, you
can readjust the laser. To do so, open the screws (32b) and
remove the front cover (32a). Loosen the Philips head screws
(E) and set the laser by moving sideways until the laser beam
strikes the teeth of the saw blade (6).
After adjusting and tightening the laser, mount the front cover
by tightening both screws (32b) by hand.
11.7 Service information
Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
Wear parts*: carbon brushes, saw blade, table inserts, saw-
dust bags
* Not necessarily included in the scope of delivery!
12. Transport
Tighten the handle (11) to lock the rotary table.
Press the machine head (4) downwards and secure with the
locking bolt (23).
Fix the saw’s drag function with the locking screw for drag
guide (20) in rear position.
Carry the equipment by the fixed saw table (15).
When reassembling the equipment proceed as described
under section 8 and 9.
13. Storage
Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust and
moisture.
Store the operating manual with the electrical tool.
14. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer‘s mains connection as well as the extension
cable used must also comply with these regula-
tions.
The product meets the requirements of EN 61000-3-11 and
is subject to special connection conditions. This means that
use of the product at any freely selectable connection point
is not allowed.
Given unfavourable conditions in the power supply the prod-
uct can cause the voltage to fluctuate temporarily.
The product is intended solely for use at connection points
that
a) do not exceed a maximum permitted supply impedance
“Z” (Zmax = 0.339 Ω), or
b) have a continuous current-carrying capacity of the mains
of at least 100 A per phase.
As the user, you are required to ensure, in consultation with
your electric power company if necessary, that the connec-
tion point at which you wish to operate the product meets
one of the two requirements, a) or b), named above.
Important information
In the event of an overloading the motor will switch itself off. Af-
ter a cool-down period (time varies) the motor can be switched
back on again.
12 GB/CY
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
Passage points, where connection cables are passed through
windows or doors.
Kinks where the connection cable has been improperly fas-
tened or routed.
Places where the connection cables have been cut due to
being driven over.
Insulation damage due to being ripped out of the wall outlet.
Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Make sure that the connection cable does not hang on the
power network during the inspection.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables of the
same designation.
The printing of the type designation on the connection cable
is mandatory.
If the power cord of this device is damaged, it must be replaced
by a special power cord, which is available from the manufac-
turer or its service department.
AC motor:
The mains voltage must be 220 - 240 V
~
.
Extension cables up to 25 m long must have a cross-section
of 1.5 mm
2
.
Connections and repairs of electrical equipment may only be
carried out by an electrician.
Please provide the following information in the event of any
enquiries:
Type of current for the motor
Machine data - type plate
15. Disposal and recycling
The equipment is supplied in packaging to prevent it from being
damaged in transit. The raw materials in this packaging can be
reused or recycled.
The equipment and its accessories are made of various types
of material, such as metal and plastic. Defective components
must be disposed of as special waste. Ask your dealer or your
local council.
The packaging is wholly composed of environment-
ally-friendly materials that can be disposed of at a
local recycling centre.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
electrical devices.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not be dis-
posed of together with domestic waste in compliance
with the Directive (2012/19/EU) pertaining to waste
electrical and electronic equipment (WEEE). This prod-
uct must be disposed of at a designated collection point. This
can occur, for example, by handing it in at an authorised col-
lecting point for the recycling of waste electrical and electronic
equipment. Improper handling of waste equipment may have
negative consequences for the environment and human health
due to potentially hazardous substances that are often con-
tained in electrical and electronic equipment. By properly dis-
posing of this product, you are also contributing to the effective
use of natural resources. You can obtain information on collec-
tion points for waste equipment from your municipal administra-
tion, public waste disposal authority, an authorised body for
the disposal of waste electrical and electronic equipment or
your waste disposal company.
13GB/CY
16. Troubleshooting
Fault Possible cause Remedy
Motor does not work Motor, cable or plug defective, fuses burnt Arrange for inspection of the machine by a specialist.
Never repair the motor yourself. Danger!
Check fuses and replace as necessary
The motor starts up slowly
and does not reach oper-
ating speed.
Voltage too low, coils damaged, capacitor burnt Contact an electrician to check the voltage.
Arrange for inspection of the motor by a specialist. Ar-
range for replacement of the capacitor by a specialist
Motor makes excessive
noise
Coils damaged, motor defective Arrange for inspection of the motor by a specialist
The motor does not reach
its full power.
Circuits in the network are overloaded (lamps,
other motors, etc.)
Do not use any other equipment or motors on the same
circuit
Motor overheats easily. Overloading of the motor, insufficient cooling of
the motor
Avoid overloading the motor while cutting, remove dust
from the motor in order to ensure optimal cooling of the
motor
Saw cut is rough or wavy Saw blade dull, tooth shape not appropriate for
the material thickness
Re-sharpen saw blade and/or use suitable saw blade
Workpiece pulls away
and/or splinters
Excessive cutting pressure and/or saw blade not
suitable for use
Insert suitable saw blade
14 GB/CY
17. Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device
develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to
call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which
guarantee claims can be made:
These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for
this guarantee.
Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these de-
fects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial ap-
plications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for
other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused
by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with
the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overload-
ing of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress
of foreign bodies into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by the device
being dropped) and normal wear resulting from proper operation of the device.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the
end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts
are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new
guarantee will become active for the work performed or parts fitted. This also applies when an on-site service is used.
In order to assert your guarantee claim, please contact the service partner shown below. If the complaint is within the guarantee pe-
riod, we will provide you with a return slip, with which you can return your defective device free of charge to us. It would help us if you
could describe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your device will
either be repaired immediately and returned to you, or we will send you a new device.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for
units which are no longer covered. To take advantage of this service, please send the device to our service address.
Service-Hotline (GB):
+800 4003 4003
(0,00 EUR/Min.)
Service-Email (GB):
service.GB@scheppach.com
Service Address (GB):
Forest Park & Garden
Coed Court, Taffsmead Road
Treforest, Ind. Estate, Pontypridd CF375SW
At www.lidl-service.com you can download this and many more manuals, product videos plus installation
software.
The QR code takes you directly to the Lidl service page (www.lidl-service.com) and you can open your oper-
ating manual by entering the article number (IAN) 331932_1907.
Service-Hotline (CY):
+800 4003 4003
(0,00 EUR/Min.)
Service-Email (CY):
Service Address (CY):
GEORGE C SOLOMONIDES & SON LTD
PO.BOX 56236 / 169, LEONTIOS A
GR - 3305 LIMASSOL/CYPRUS
15HR
Sadržaj: Stranica:
1. Objašnjenje simbola na uređaju ......................................................................................................................................................................16
2. Uvod ..................................................................................................................................................................................................................17
3. Opis uređaja (slika 1-22) .................................................................................................................................................................................17
4. Opseg isporuke .................................................................................................................................................................................................18
5. Namjena ............................................................................................................................................................................................................18
6. Sigurnosne napomene ......................................................................................................................................................................................18
7. Tehnički podaci .................................................................................................................................................................................................21
8. Prije pokretanja opreme ...................................................................................................................................................................................22
9. Priključivanje ......................................................................................................................................................................................................22
10. Rad .....................................................................................................................................................................................................................23
11. Održavanje .......................................................................................................................................................................................................24
12. Prijevoz ..............................................................................................................................................................................................................25
13. Skladištenje ........................................................................................................................................................................................................25
14. Električni priključak ............................................................................................................................................................................................25
15. Zbrinjavanje i recikliranje .................................................................................................................................................................................26
16. Rješavanje problema ........................................................................................................................................................................................27
17. Jamstveni certifikat .............................................................................................................................................................................................28
18. Izjava o sukladnosti .......................................................................................................................................................................................108
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Parkside 3901227974 Operating And Safety Instructions Manual

Tip
Operating And Safety Instructions Manual
Acest manual este potrivit și pentru