Eizo RX250 Manualul proprietarului

Categorie
Televizoare
Tip
Manualul proprietarului
English
Instructions for Use
Color LCD monitor
Important
Please read this “Instructions for Use”, and “Installation Manual”
(separate volume) carefully to familiarize yourself with safe and
effective usage.
Please retain this manual for future reference.
For monitor adjustment and settings, refer to the “Installation
Manual”.
For the latest product information including the “Instructions for
Use”, refer to our web site :
http://www.eizoglobal.com
2
SAFETY SYMBOLS
This manual and this product use the safety symbols below. They denote critical information. Please read
them carefully.
WARNING
Failure to abide by the information in a
WARNING may result in serious injury
and can be life threatening.
CAUTION
Failure to abide by the information in a
CAUTION may result in moderate injury and/or
property or product damage.
Indicates a warning or caution. For example, indicates an “electrical shock” hazard.
Indicates a prohibited action. For example, means “Do not disassemble”.
Indicates a mandatory action. For example, means “Ground the unit.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
3
PRECAUTIONS
English
PRECAUTIONS
IMPORTANT
This product has been adjusted specically for use in the region to which it was originally shipped.
If the product is used outside the region, it may not operate as specied in the specications.
To personal safety and proper maintenance, please read carefully this section and the caution
statements on the monitor.
Location of the Caution Statements
AVERTISSEMENT
WARNING
WARNUNG
Symbols on the unit
Symbol This symbol indicates
Main Power Switch: Press to turn the monitor’s main power off.
Main Power Switch: Press to turn the monitor’s main power on.
Power button: Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
CAUTION: Refer to “SAFETY SYMBOLS” (page 2).
WEEE marking:
Product must be disposed of separately; materials may
be recycled.
CE marking:
EU conformity mark in accordance with the provisions of
Council Directive and/or Regulation (EU).
Manufacturer
Date of manufacture
4
PRECAUTIONS
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes strange noises, discon-
nect all power connections immediately and contact your EIZO representative for advice.
Attempting to use a malfunctioning unit may result in re, electric shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in re, electric shock, or burn.
Refer all servicing to qualied service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in re, electric
shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage
into the cabinet may result in re, electric shock, or equipment damage. If an object or
liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by
a qualied service engineer before using it again.
Place the unit at a sturdy and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment damage. If the unit falls,
disconnect the power immediately and ask your local EIZO representative for advice. Do not continue using
a damaged unit. Using a damaged unit may result in re or electric shock.
Use the unit in an appropriate location.
Otherwise, re, electric shock, or equipment damage may result.
Do not place outdoors.
Do not place in any form of transportation (ships, aircraft, trains, automobiles, etc.).
Do not place in dusty or humid environments.
Do not place in locations where water may be splashed on the screen (bathrooms, kitchens,
etc.)
Do not place in locations where steam comes in direct contact with the screen.
Do not place near heat generating devices or humidiers.
Do not place in locations where the product is subject to direct sunlight.
Do not place in environments with inammable gas.
Do not place in environments with corrosive gases (such as sulfur dioxide, hydrogen sulde,
nitrogen dioxide, chlorine, ammonia, and ozone)
Do not place in environments with dust, components that accelerate corrosion in the
atmosphere (such as sodium chloride and sulfur), conductive metals, and so on
To avoid danger of suffocation, keep the plastic packing bags away from babies and children.
Use the enclosed power cord and connect to the standard power outlet in your country.
Be sure to use within the rated voltage of the power cord. Otherwise, re or electric shock may result.
Power supply: 100-240Vac 50/60Hz
To disconnect the power cord, grasp the plug rmly and pull.
Tugging on the cord may damage and result in re or electric shock.
The equipment must be connected to a grounded main outlet.
Failure to do so may result in re or electric shock.
Use the correct voltage.
The unit is designed for use with a specic voltage only. Connection to another voltage than specied in this
“Instructions for Use” may cause re, electric shock, or equipment damage.
Power supply: 100-240Vac 50/60Hz
Do not overload your power circuit, as this may result in re or electric shock.
5
PRECAUTIONS
English
WARNING
Handle the power cord with care.
Do not place the cord underneath the unit or other heavy objects.
Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Using of a damaged cord may result
in re or electric shock.
For electrical safety, do not connect or disconnect the power cord in the presence of patients.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit
securely.
Otherwise, the unit may become detached, resulting in injury and/or equipment damage. Before installation,
make sure that desks, walls, or any other installation surface has adequate mechanical strength. If the unit
falls, please ask your local EIZO representative for advice. Do not continue using a damaged unit. Using
a damaged unit may result in re or electric shock. When reattaching the tilt stand, please use the same
screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
Liquid crystal is poisonous. If any part of your skin comes in direct contact with the
panel, wash thoroughly. If liquid crystal enters your eyes or mouth, immediately ush
with large amounts of water and seek medical attention.
Fluorescent backlight lamps contain mercury (the products that have LED back-
light lamps contain no mercury), dispose according to local, state or federal
laws.
Exposure to elemental mercury can result in effects on the nervous system, including
tremors, memory loss, and headaches.
6
PRECAUTIONS
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the power cord or cables
attached is dangerous and may result in injury.
Carry or place the unit according to the correct specied methods.
When carrying, grasp and rmly hold the unit as shown in the illustration below.
Monitors of size 30 inches and above are heavy. When unpacking and/or carrying the monitor,
ensure at least two people are utilized.
Dropping the unit may result in injury or equipment
damage.
Do not block the ventilation slots on the cabinet.
Do not place any objects on the ventilation slots.
Do not install the unit in a place with poor ventilation or inadequate space.
Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airow and may result in re, electric
shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This is to facilitate disconnecting the power in case of a problem.
Periodically clean the area around the power plug and the ventilation slot of the monitor.
Dust, water, or oil on the plug may result in re.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period of time, disconnect the power cord from
the wall socket after turning off the power switch for the safety and the power conservation.
This product is suitable for placing near patients, but not for direct contact with patients.
For users in the territory of the EEA and Switzerland:
Any serious incident that has occurred in relation to the device should be reported to the
Manufacturer and the Competent Authority of the Member State in which the user and/or patient is
established.
7
Notice for this monitor
English
Notice for this monitor
Intended use
This product is intended to be used in displaying and viewing digital images for review, analysis and
diagnosis by trained medical practitioners. It does not support the display of mammography images
for diagnosis.
Caution: Federal law (USA) restricts this device to sale by or on the order of a physician.
Attention
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
- Power cords provided with the product
- Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
Installation Requirements
Carefully read the “PRECAUTIONS” (page 3) and always follow the instructions.
When installing the monitor in a rack, ensure that there is adequate space around the sides, back
and top of the monitor.
Position the monitor so that there is no light to interfere with the screen.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of
the stand due to the composition of the rubber. Check the desk surface before use.
Maintenance
The display quality of monitors is affected by the quality level of input signals and the degradation of
the product. It is recommended that daily checkups and periodical constancy test be performed to
comply with medical standards/guidelines according to your application. Use of the RadiCS monitor
quality control software enables you to perform high-level total quality control that meets medical
standards/guidelines.
It takes about 15 minutes for the performance of electrical parts to stabilize. Please wait 15 minutes
or more after the monitor power has been turned on or the monitor has recovered from the power
saving mode, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term
use and maintain a stable display. Periodically perform constancy tests. Calibrate if necessary. For
details, refer to the User Manuals for the RadiCS/RadiCS LE monitor quality control software.
To maintain the measurement accuracy of the integrated front sensor, perform periodical correlation
using RadiCS/RadiCS LE.
Parts (such as the LCD panel) may deteriorate over the long term. Periodically check that they are
operating normally.
When the screen image is changed after displaying the same image for extended periods of time,
an afterimage may appear. Use the screen saver or power save function to avoid displaying the
same image for extended periods of time.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may
appear. To maximize the life of the monitor, we recommend the monitor be turned off periodically.
8
Notice for this monitor
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to
icker, please contact your local EIZO representative.
The screen may have defective pixels or a small number of light dots on the screen. This is due to
the characteristics of the panel itself, and is not a malfunction of the product.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions,
such as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate
or damage your panel. (If the pressure marks remain on the panel, leave the monitor with a black or
white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not
turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause
some damage to the monitor.
Cleaning
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation
lifetime.
Attention
Do not use chemicals on a frequent basis. Chemicals such as alcohol and antiseptic solution may cause
gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image.
Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Do not let chemicals come into direct contact with the monitor.
Note
The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
Gently wipe off any dirt on the cabinet or panel surface with a soft cloth soaked in a small amount of
water or one of the chemicals listed below.
Chemicals that may be used for cleaning
Material name Product name
Ethanol Ethanol
Isopropyl alcohol Isopropyl alcohol
Chlorhexidine Hibitane
Sodium hypochlorite Purelox
Benzalkonium chloride Welpas
Alkyldiaminoethylglycine Tego 51
Glutaral Sterihyde
Glutaral Cidex Plus28
To use the monitor comfortably
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
Look at the screen from a proper distance and from a proper angle.
9
CONTENTS
English
CONTENTS
PRECAUTIONS ...................................................... 3
IMPORTANT .............................................................. 3
Notice for this monitor ......................................... 7
CONTENTS ............................................................. 9
Chapter 1 Introduction ..................................... 10
1-1. Features ........................................................10
1-2. Package Contents ........................................11
1-3. EIZO LCD Utility Disk...................................11
Disk contents and software overview ............11
Using RadiCS LE ...........................................11
1-4. Controls and Functions ..............................12
1-5. Compatible Resolutions .............................13
Chapter 2 Connection ...................................... 14
2-1. Connecting Cables ......................................14
2-2.
Making Use of USB (Universal Serial Bus)
...16
Required system environment .......................16
Connection procedure (Setup of USB function)
...17
Chapter 3 Setting Up ........................................ 18
3-1. Adjusting the Screen Height and Angle .... 18
3-2. Attaching Arm ..............................................19
Chapter 4 Troubleshooting .............................. 20
Chapter 5 Specications ................................. 21
5-1. Specications List .......................................21
5-2. Main Default Settings ................................. 22
5-3. Dimensions .................................................. 23
5-4. Accessories ................................................. 23
Chapter 6 Glossary .......................................... 24
Appendix .............................................................. 26
Trademark ............................................................... 26
License / Copyright ................................................ 27
Medical Standard ................................................... 27
EMC Information .................................................... 28
FCC Declaration of Conformity ............................ 33
Declaration of compliance with India RoHS ....... 34
Recycling Information/
Informationen zum Thema Recycling/
Informations sur le recyclage/
Сведения по утилизации .................................... i
10
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
21.3 inches
Supports a resolution of 2M pixels (Portrait: 1200 × 1600 dots (H × V))
Uses high-contrast panel (1400 : 1).
Enables the display of sharp images.
Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals)
The daisy-chain function is included enabling multiple monitors to be connected with the
DisplayPort cable.
A graphic board supporting DisplayPort1.2 is required. For details, refer to the EIZO website.
http://www.eizoglobal.com
The CAL Switch function allows the user to select the display mode optimum to the displayed
image.
Refer to the Installation Manual (on the CD-ROM).
Selectable DICOM (page 24) Part 14 complied screen.
The quality control software “RadiCS LE” used to calibrate the monitor and to manage the history is
included.
See “1-3. EIZO LCD Utility Disk” (page 11).
Power saving function
This product is equipped with power saving function.
- 0 W power consumption when the main power is off
Equipped with main power switch.
When not using the monitor, you can turn off the main power supply so that the power is cut completely.
- Presence Sensor
The sensor on the front side of the monitor detects the movement of a person. When a person moves
away from the monitor, the monitor shifts to the power saving mode automatically and does not display the
images on the screen. Therefore, the function reduces the power consumption.
Refer to the Installation Manual (on the CD-ROM).
Low-prole and lightweight design
Long service life LED backlight LCD panel
Built-in ambient light sensor
Depending on the environment, the sensor sometimes indicates different values from those measured by a
stand-alone illuminance meter.
The usage of this sensor requires the quality control software “RadiCS/RadiCS LE” and the measurement is
always triggered by the user’s operation in the corresponding menu. For further details about the measured
value and how to execute the measurement, refer to the RadiCS/RadiCS LE Users Manual (on the CD-ROM).
11
Chapter 1 Introduction
English
1-2. Package Contents
Check that all the following items are included in the packaging box. If any items are missing or damaged,
contact your local EIZO representative.
Note
Please keep the packaging box and materials for future movement or transport of the monitor.
Monitor
Power cord
Digital signal cable : PP300
DisplayPort - DisplayPort
Digital signal cable : DD300
DVI - DVI (Single Link)
USB cable : UU300
EIZO LCD Utility Disk (CD-ROM)
Instructions for Use (this manual)
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
Disk contents and software overview
The disk includes quality control software and User’s Manual. Refer to Readme.txt le on the disk for
software startup procedures or le access procedures.
Contents Overview
Readme.txt le
RadiCS LE (for Windows) Quality control software for calibrating the monitor and managing the
calibration history.
Installation Manual of this monitor (PDF le)
“Instructions for Use” of this monitor (PDF le)
Using RadiCS LE
For the installation and use of RadiCS LE, refer to the Users Manual on the disk.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable
(see “2-2. Making Use of USB (Universal Serial Bus)” (page 16)).
Note
Using DDC communication allows you to use RadiCS LE without having to use the USB cable. For
information on how to congure DDC communication, refer to the Installation Manual (on the CD-ROM).
12
Chapter 1 Introduction
1-4. Controls and Functions
12
13
4 53 7 8 9 10 116
6
14
1 2
15
Adjustment menu*1
Approx. 30˚
1. Integrated Front Sensor
(Mobile)
Detects the movement of a person in front of the monitor.
2. Ambient Light Sensor Measures the environmental illumination.
3. Presence Sensor Detects the movement of a person in front of the monitor.
4. Operation switches Displays the menu. Follow the guide to perform the desired operations.
5.
switch
Turns the power on or off.
Indicates the monitor’s operation status.
Green: Operating, Orange: Power saving mode, Off: Main power/power off
6. USB downstream port Connects a peripheral USB device.
7. USB upstream port Connects the USB cable to use the software that needs USB connection, or to use
USB Hub function.
8. DVI-D connector Connect it to the PC.
9. DisplayPort input
connector
Connect it to the PC. To set up a daisy-chain connection, connect the cable to the
output connector of an upstream monitor.
10. DisplayPort output
connector
To set up a daisy-chain connection, connect the cable to the input connector of a
downstream monitor.
11. Power connector Connects the power cord.
12. Stand Used to adjust the height and angle of the monitor screen.
13. Main power switch Turns the main power on or off.
: Off : On
14. Security lock slot Complies with Kensington’s MicroSaver security system.
15. Cable holder Covers the monitor cables.
*1 For instructions for use, refer to the Installation Manual (on the CD-ROM).
13
Chapter 1 Introduction
English
1-5. Compatible Resolutions
The monitor supports the following resolutions.
√ : Supported
Resolution
vertical scan
frequency
DisplayPort
*1
DVI
Portrait Landscape Portrait Landscape
720 × 400 70 Hz
640 × 480 60 Hz
800 × 600 60 Hz
1024 × 768 60 Hz
1280 × 1024 60 Hz - -
1200 × 1600 60 Hz - -
1600 × 1200 60 Hz - -
*1 Supports 10-bit displays.
14
Chapter 2 Connection
Chapter 2 Connection
2-1. Connecting Cables
Attention
Check that the monitor and the PC are powered off.
When replacing the current monitor with this monitor, refer to “1-5. Compatible Resolutions” (page 13) to
change the PC settings for resolution and vertical scan frequency to those that are available for this monitor,
before connecting the PC.
1.
Turn the monitor screen 90˚ in clockwise direction.
The landscape position is the default monitor orientation.
Attention
Before turning the monitor screen, raise it to the highest position.
2.
Connect signal cables.
Check the shapes of the connectors, and connect the cables. After connecting the DVI cable, tighten
the fasteners to secure the connector.
Connecting to a single PC
Attention
The DisplayPort connectors of the monitor consist of input and output . When connecting a monitor to a
PC, connect the cable to input connector
.
Signal cable :
DD300
Signal cable : PP300
or
15
Chapter 2 Connection
English
Connecting to multiple PCs
For information on how to switch the input signals, refer to the Setup manual (on the CD-ROM).
Daisy-chaining multiple monitors
Attention
Visit the EIZO website for information about monitors and graphic boards that can be used for the daisy-chain
connection: http://www.eizoglobal.com
Remove the
cap before connecting the signal cable.
Connecting to a Computer
Signal cable : PP300 Signal cable : PP200
Signal cable : DD300
Signal cable : PP300
Signal cable : PP300
16
Chapter 2 Connection
3.
Plug the power cord into a power outlet and the power connector on the
monitor.
4.
Connect the USB cable when using RadiCS LE.
For information about the connection to the USB upstream port, refer to “2-2. Making Use of USB
(Universal Serial Bus)” (page 16).
Connecting to the Monitor Connecting to a Computer
Note
Using DDC communication allows you to use RadiCS LE without having to use the USB cable. For
information on how to congure DDC communication, refer to the Installation Manual (on the CD-ROM).
5.
Touch to turn on the power to the monitor.
The monitor’s power indicator lights up green.
6.
Turn on the PC.
The screen image appears.
If an image does not appear, refer to “Chapter 4 Troubleshooting” (page 20) for additional advice.
Attention
For the maximum power saving, it is recommended that the Power button be turned off. When not using
the monitor, you can turn off the main power supply or disconnect the power plug so that the power is cut
completely.
Note
In order to maximize the monitor life and to minimize luminance deterioration as well as power consumption,
proceed the following:
- Use the power saving function of the computer.
- Turn off the monitor and PC after using them.
2-2. Making Use of USB (Universal Serial Bus)
This monitor has a hub compatible with USB. Connected to a PC compatible with USB or another USB
hub, this monitor functions as a USB hub allowing connection to peripheral USB devices.
Required system environment
A PC equipped with a USB port or another USB hub connected to a USB compatible PC
Windows 10 / Windows 8.1 / Windows 8 / Windows 7 / Windows Vista / Windows XP, or Mac OS X
10.2 or later
USB cable
Attention
This monitor may not work depending on PC, OS or peripheral devices to be used. For USB compatibility of
peripheral devices, contact their manufacturers.
Devices connected to the USB downstream port still work when the monitor is in power saving mode or when
the power is switched off using only the power button of the monitor. Therefore, power consumption of the
monitor varies with connected devices even in the power saving mode.
When the main power switch is Off, device connected to the USB port will not operate.
17
Chapter 2 Connection
English
Connection procedure (Setup of USB function)
1. Connect the monitor rst to a PC using the signal cable, and run the PC.
2. Connect the supplied USB cable between the USB downstream port of a USB compatible PC (or
another USB hub) and the monitor’s USB upstream port.
The USB hub function is set up automatically upon connection of the USB cable.
3. Connect the peripheral USB device to the USB downstream port of the monitor.
USB
downstream
port
USB
upstream
port
18
Chapter 3 Setting Up
Chapter 3 Setting Up
3-1.
Adjusting the Screen Height and Angle
Hold left and right edge of the monitor with both hands, and adjust the screen height, tilt and swivel of the
screen to the best condition for working.
Attention
After carrying out the adjustment, make sure that the cables are connected correctly, and put them through the
cable holder.
19
Chapter 3 Setting Up
English
3-2.
Attaching Arm
An optional arm (or an optional stand) can be attached by removing the stand section. For supported
optional arms (or optional stands), refer to the EIZO website: http://www.eizoglobal.com
Attention
When attaching an arm or stand, follow the instructions of their Users Manual.
When using another manufacturer’s arm or stand, conrm the following in advance and select one conforming to
the VESA standard.
- Clearance between the screw holes: 100mm × 100 mm
- VESA mount of the arm or stand, external dimensions: 122 mm x 122 mm or less
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
When using another manufacturer’s arm or stand, use the following screws to secure it.
- Screws xing the stand to the monitor
When using an arm or stand, attach it to meet the following tilt angles of the monitor.
- Up 45˚, down 45˚ (when the portrait orientation is used, and when rotated 90° counterclockwise for landscape
display)
Connect the cables after attaching an arm or stand.
Do not move the removed stand up and down. Doing so may result in injury or device damage.
The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
Periodically check the tightness of the screws. If not sufciently tight, the monitor may detach from the arm, which
may result in injury or equipment damage.
Procedure
1.
Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2.
Remove the stand.
Prepare a screwdriver. Loosen the screws (four) securing the unit and the stand with the screwdriver.
3.
Attach the arm or stand to the monitor.
Use the screws that you removed in step 2 to attach the arm (or stand) to the monitor.
20
Chapter 4 Troubleshooting
Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
Problem Possible cause and remedy
1. No picture
Power indicator does not light.
Check whether the power cord is connected properly.
Turn the main power switch on.
Touch
.
Turn off the main power, and then turn it on again.
Power indicator is lighting green. • Increase “Brightness”, “Contrast, and/or “Gain” in the
Adjustment menu. For details, refer to the Installation
Manual (on the CD-ROM).
Turn off the main power, and then turn it on again.
Power indicator is lighting orange. • Switch the input signal. For details, refer to the Installation
Manual (on the CD-ROM).
Move the mouse or press any key on the keyboard.
Check whether the PC is turned on.
When Presence Sensor is set to “On”, the monitor may
have shifted to the power saving mode. Come near to the
monitor.
Check if the signal cable is connected to
for inputting
the DisplayPort signal.
is used for output when a daisy-
chain connection is set up.
Turn off the main power, and then turn it on again.
Power indicator is ashing orange and green. Connect via the signal cable specied by EIZO. Turn off
the main power, and then turn it on again.
When connected to DisplayPort, switch the version of
DisplayPort to 1.1. For details, refer to the Installation
Manual (on the CD-ROM).
2. The message below appears. This message appears when the signal is not input correctly
even when the monitor functions properly.
This message appears when no signal is
input.
Example:
The message shown left may appear, because some PCs
do not output the signal soon after power-on.
Check whether the PC is turned on.
Check whether the signal cable is connected properly.
Switch the input signal. For details, refer to the Installation
Manual (on the CD-ROM).
When connected to DisplayPort, switch the version of
DisplayPort to 1.1.
Check if the signal cable is connected to
for inputting
the DisplayPort signal.
is used for output when a daisy-
chain connection is set up.
Turn off the main power, and then turn it on again.
The message shows that the input signal is
out of the specied frequency range.
Example:
Check whether the PC is congured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “1-5. Compatible Resolutions” (page 13)).
Reboot the PC.
Select an appropriate setting using the graphics board’s
utility. Refer to the manual of the graphics board for
details.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

Eizo RX250 Manualul proprietarului

Categorie
Televizoare
Tip
Manualul proprietarului

în alte limbi