Eizo FDF2382WT Manual de utilizare

Important

Please read this “User’s Manual”, and “PRECAUTIONS” (separate

volume) carefully to familiarize yourself with safe and eective usage.

• Refer to the “Setup Guide” for information on the installation /

connection of the monitor.

• For the latest product information including the “User’s Manual”,

refer to our web site :

www.eizoglobal.com

Touch Panel Color LCD Monitor

User’s Manual

2

Location of Caution Statement

Symbols on the unit

Symbol This symbol indicates

Power button

Press to turn the monitor’s power on or o.

Alternating current

Alerting electrical hazard

CAUTION

Refer to SAFETY SYMBOLS section in PRECAUTIONS.

WEEE marking

Product must be disposed of separately; materials may be recycled.

CE marking

EU conformity mark in accordance with the provisions of Council Directive 93/42/EEC

and 2011/65/EU.

This product has been adjusted specically for use in the region to which it was originally shipped. If

operated outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by

any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless

prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every

eort has been made to ensure that this manual provides up-to-date information, please note that EIZO

monitor specications are subject to change without notice.

3

Notice for This Monitor

This product is suited to general purposes like creating documents, viewing multimedia content (Assuming

usage of approximately 12 hours per day).

This product has been adjusted specically for use in the region to which it was originally shipped. If the

product is used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

• Power cords provided with the product

• Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to

the composition of the rubber. Check the desk surface before use.

It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more

after the monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and

maintain a stable display.

When the screen image is changed after displaying the same image for extended periods of time, an

afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for

extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for

a short period of time. To remove such a phenomenon, change the image or keep the power turned o for

several hours.

If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To

maximize the life of the monitor, we recommend the monitor be turned o periodically.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer

to “Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may

appear on the LCD panel, this is not a malfunction. Percentage of eective dots: 99.9994 % or higher.

The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for

long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the

screen becomes dark or begins to icker, please contact your local EIZO representative.

Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD

panel. Do not attempt to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew

condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the

monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the

monitor.

(Cautions for the Use of the Touch Panel)

During touch operation

Be careful of the following points. Otherwise, damage may occur to the monitor.

• Do not strongly press, scratch, or poke the panel.

• Do not touch the panel with hard objects such as ballpoint pens or metals.

4

Notice for This Monitor

Cleaning

The stains on the cabinet and LCD panel surface can be removed by using the provided cleaning cloth.

Attention

• Do not allow liquid to enter the clearance between the panel and the panel frame.

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet

or LCD panel, and also quality deterioration of the image.

• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.

To Use the Monitor Comfortably

• An excessively dark or bright screen may aect your eyes. Adjust the brightness of the monitor

according to the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5

CONTENTS

Notice for This Monitor ......................................... 3

Cleaning .................................................................... 4

To Use the Monitor Comfortably ............................ 4

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 6

1-1. Features ......................................................... 6

●

Full-at Design ................................................ 6

●

Easy-to-touch Stand Mechanism .................... 6

●

10-point Multi-touch Function ......................... 6

1-2. Controls and Functions ............................... 7

●

Front ................................................................ 7

●

Rear ................................................................. 8

1-3. Attaching the Touch Pen Holder ................. 9

1-4. EIZO LCD Utility Disk.................................... 9

●

Disk Contents and Software Overview ........... 9

Chapter 2 Basic Adjustment / Setting ............ 10

2-1. Enabling or Disabling the Touch Panel .....10

2-2. Switching the Input Signal ..........................10

2-3. Adjusting Brightness ..................................11

2-4. Adjusting Volume.........................................11

Chapter 3 Touch Panel Settings ..................... 12

3-1. Touch Panel Setting Method ......................12

3-2. Adjusting the Touch Position .....................12

3-3. Conguring Touch Panel Operation

Settings .........................................................14

Chapter 4 Advanced Adjustment / Setting .... 15

4-1. Basic Operation of the Setting Menu ........15

4-2. Color ..............................................................16

●

Color Mode .....................................................16

●

Brightness ......................................................16

●

Contrast ..........................................................17

●

Temperature ...................................................17

●

Gamma ...........................................................17

●

Advanced Settings .........................................18

●

Color Reset ....................................................18

4-3. Screen ...........................................................19

●

Screen Size ....................................................19

●

Smoothing ......................................................19

●

Analog Adjustment ........................................ 20

4-4. Sound ............................................................21

●

Source ............................................................21

4-5. PowerManager ............................................ 22

●

Power Save ................................................... 22

●

Eco Timer ...................................................... 22

4-6. Monitor Settings ......................................... 23

●

Input Signal ................................................... 23

●

Power Indicator ............................................. 23

●

Languages .................................................... 23

●

Menu Settings ................................................24

●

Reset ..............................................................24

4-7. Information .................................................. 24

4-8. Locking Operation Buttons ....................... 24

Chapter 5 Troubleshooting .............................. 25

5-1. No Picture .................................................... 25

5-2. Imaging Problems

(for both digital and analog) ...................... 26

5-3. Imaging Problems (for analog only) ......... 27

5-4. Imaging Problems (for digital only) .......... 27

5-5. Touch Panel Problems ............................... 28

5-6. Other Problems ........................................... 30

Chapter 6 Reference ........................................ 31

6-1. Attaching the Optional Arm ........................31

6-2. Connecting Multiple PCs ........................... 33

6-3. Specications ............................................. 34

●

Compatible Resolutions ................................ 35

●

Main Default Settings .................................... 36

●

Accessories ................................................... 36

Appendix .............................................................. 37

Trademark ................................................................37

License .....................................................................37

FCC Declaration of Conformity ............................ 38

LIMITED WARRANTY ............................................. 39

Recycling Information ........................................... 40

6

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

●

Full-at Design

The full-at design with no steps is adopted in the bezel part. You can securely touch up to each edge

of the screen even with ngertips.

●

Easy-to-touch Stand Mechanism

The tilt angle can be adjusted steplessly. You can smoothly change to the easy-to-work screen

position to suit your needs such as for oce work or multi-touch operations.

15°

70°

●

10-point Multi-touch Function

You can perform operations such as enlargement, reduction, and rotation using the multi-touch

function. The touch panel reacts via light touching of the screen with ngers, thereby, enabling

comfortable ick and drag operations.

Enlarge / Reduce

Rotate

7

Chapter 1 Introduction

1-2. Controls and Functions

●

Front

1

2

3

4

5

6

7

Setting menu

*1

1. Power indicator

Indicates the monitor’s operation status.

Blue: Screen display

Orange: Power saving mode

OFF: Main power o / Power o

2.

button

Switches the touch panel enable and disable modes, or calibrates the

touch sensitivity (page 10).

3.

button

Switches input signals for display (page 10).

4.

button

*2

Provides an item selection and function adjustment or setting option while

the Setting menu is displayed, and displays the brightness adjustment

screen (page 11).

5.

button

*2

Provides an item selection and function adjustment or setting option while

the Setting menu is displayed, and displays the volume control screen

(page 11).

6.

button

Displays the Setting menu, determines an adjustment item of each menu,

and saves values adjusted (page 15).

7.

button

Turns the power on or o.

*1 For information on how to use, see “4-1. Basic Operation of the Setting Menu” (page 15).

*2 In this User’s Manual, the

button may be hereafter simply referred as , and the button as .

8

Chapter 1 Introduction

●

Rear

11

12

13

8

9

10

14

15

17

18

16

8. Main power switch

Turns the main power on or o.

| : ON, ○: OFF

9. Power connector Connects the power cord.

10. Touch pen holder attachment

hole

*3

Used to attach a touch pen holder.

11. Security lock slot Complies with Kensington’s MicroSaver security system.

12. Speaker Outputs audio source.

13. Stand

(with cable holder)

Used to adjust the angle of the monitor screen.

14. Headphone jack Connects the headphones.

15. Analog voice input connector Outputs external voice from the monitor.

16. Input signal connector

Connect it to the PC.

Upper port: D-Sub mini 15-pin connector

Medium port: DVI-D connector

Lower port: DisplayPort connector

17. USB downstream port Connects a peripheral USB 2.0 device.

18. USB upstream port

Connects the USB cable for using the monitor as a touch panel monitor or

for using the USB Hub function.

*3 The touch pen holder is supplied with the touch pen (Accessories (page 36)). For the attachment method,

see “1-3. Attaching the Touch Pen Holder” (page 9).

9

Chapter 1 Introduction

1-3. Attaching the Touch Pen Holder

Note

• The touch pen holder is supplied with the touch pen (Accessories (“Accessories” (page 36))).

Attach the touch pen holder to any one of the right-hand and left-hand holes in the rear of the monitor. To

x the touch pen holder, use the screw supplied with the touch pen.

1-4. EIZO LCD Utility Disk

An "EIZO LCD Utility Disk" (CD-ROM) is supplied with this product. The following table shows the disk

contents and the overview of the software programs.

●

Disk Contents and Software Overview

The disk includes adjustment software, touch panel software, and User’s Manual. For software

startup procedures or le access procedures, see the Readme.txt le on the disk.

Item Overview

Touch panel driver Touch panel driver supplied by EIZO.

*

1

TPOset Software for calibrating the sensitivity of the touch panel.

*

1

Use this software when touch operations are not registered or only registered

after pressing hard.

User’s Manual of this monitor (PDF le)

Outline dimensions

Readme.txt le

*1 Only for Windows. Refer to the corresponding User’s Manual on the CD-ROM for details on installation

and use.

10

Chapter 2 Basic Adjustment / Setting

2-1. Enabling or Disabling the Touch Panel

You can switch the touch panel enable and disable modes. This function is available when you want to

temporarily display the touch panel function.

Note

• Holding down allows you to calibrate the touch sensitivity.

2-2. Switching the Input Signal

When a monitor has multiple signal inputs, the signal to display on-screen can be changed.

When the signal is switched, the active input port name appears at the top right corner of the screen.

11

Chapter 2 Basic Adjustment / Setting

2-3. Adjusting Brightness

The brightness of the screen can be adjusted to suit the installation environment or personal preference.

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD

back panel).

Adjustable range

0 to 100

2-4. Adjusting Volume

You can individually tune the speaker or headphone volume.

Adjustable range

0 to 30

12

Chapter 3 Touch Panel Settings

3-1. Touch Panel Setting Method

This product’s touch panel functions vary depending on the driver you use and its settings. Congure

settings to meet your usage applications.

Function

Windows standard

driver

Dedicated touch panel driver (DMT-DD)

*1

Driver installation Not required Required

Touch sound output x √

Multi-connection

*2

r

*3

√

Operation mode Touch digitizer

*4

Touch digitizer

*4, 5

Mouse emulation

*5

Multi-touch operation √ √ x

*1 Included in the EIZO LCD Utility Disk (CD-ROM).

*2 √: Two or more monitors can be connected to a single computer.

*3 Only available in Windows 10.

*4 Touch operation may not be recognized on an application designed by mouse emulation.

*5 For more information about the setup procedure, see the touch panel driver’s User’s Manual (included on the

CD-ROM).

Note

• When setting is completed, execute the "TPOset" application included on the CD-ROM, and calibrate the

sensitivity of the touch panel.

When using the Windows standard driver, congure settings, referring to the following information.

3-2. Adjusting the Touch Position

Make adjustments to align the touch position with the position of the cursor displayed in response to

touching.

Attention

• Do not put your hands or any metal close to the screen because the screen is susceptible to electrical conductors.

• If a “User Account Control” dialog box is displayed during operation, proceed according to the displayed

instructions.

1.

Open Windows Control Panel.

The method for opening Control Panel diers depending on the operating system.

Windows 10

1. Open the Start menu, and click "All apps" - "Windows System" - "Control Panel".

Windows 8.1

1. Click

at the bottom of the "Start" screen.

The “Apps” screen appears.

2. Click “Control Panel” under “Windows System”.

Windows 7

1. Click “Start” - “Control Panel”.

13

Chapter 3 Touch Panel Settings

2.

Click "Hardware and Sound" - "Tablet PC Settings".

The “Tablet PC Settings” window appears.

3.

Click "Setup" in the "Display" tab.

A touchscreen specication screen with a white background is displayed.

Attention

• If using the monitor in a multiple monitor environment, specify the touchscreen according to the message

displayed on screen.

4.

Touch the screen with your nger.

The touched screen is recognized as a touchscreen.

5.

Press "Enter" on the keyboard.

The “Tablet PC Settings” window reappears.

6.

Click "Calibrate".

A screen with a white background is displayed.

Attention

• If using the monitor in a multiple monitor environment, select the monitor to calibrate the touch position for the

"Display" pull-down menu, and then click "Calibrate".

7.

Touch the calibration target (cross) for a few seconds with your nger and

release.

The calibration target appears on the screen 16 times, starting from the top left to top right and then

down to the bottom left to bottom right.

Note

• For second or subsequent calibrations, the calibration target appears 4 times.

8.

After the touch position calibration has been completed, click "Yes" to save

the calibration data.

9.

Click "OK" to close the window.

14

Chapter 3 Touch Panel Settings

3-3. Conguring Touch Panel Operation Settings

1.

Open Windows Control Panel.

The method for opening Control Panel diers depending on the operating system. (See page 12)

2.

Click "Hardware and Sound" - "Pen and Touch".

“Pen and Touch” window appears.

Congure the touch panel operation settings in the “Pen and Touch” window. For detailed settings,

refer to the settings on each tab and Windows Help.

3.

After settings have been completed, click "OK" to close the window.

15

Chapter 4 Advanced Adjustment / Setting

This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.

4-1. Basic Operation of the Setting Menu

1.

Displaying the Setting menu

1. Press to open the Setting menu.

2.

Adjustment / Setting

1. Use to select a menu to adjust or set, and press . The Sub menu appears.

2. Use to select an item to adjust or set, and press . The adjustment / setting menu appears.

3. Use to perform adjustment / setting, and press to apply the setting.

3.

Exiting

1. Select "Return" from the Sub menu, and press . The Setting menu appears.

2. Select "Exit" in the Setting menu, and press

. The Setting menu exits.

Note

• The Setting menu can also be exited by pressing twice quickly.

16

Chapter 4 Advanced Adjustment / Setting

4-2. Color

●

Color Mode

This function allows easy selection of a desired mode according to monitor application.

Mode Purpose

User1 Select this to dene a desired set of parameter settings.

User2

sRGB Suitable for color matching with sRGB compatible peripherals.

Functions that can be adjusted dier depending on the color mode.

√: Adjustable -: Not adjustable

Function

Color Mode

User1 User2 sRGB

Brightness √ √ √

Contrast √ √ -

Temperature √ √ -

Gamma √ √ -

Advanced

Settings

Hue √ √ -

Saturation √ √ -

Overdrive √ √ -

Gain √ √ -

Reset √ √ √

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more

after the monitor power has been turned on, and then adjust the monitor.

• Perform the range adjustment rst when adjusting color for analog signals (see “Auto Range Adjust” (page

20)).

• The same image may be seen in dierent colors on multiple monitors due to their monitor-specic

characteristics. Make ne color adjustment visually when matching colors on multiple monitors.

●

Brightness

The screen brightness is adjusted by changing the brightness of the backlight (light source from the

LCD back panel).

Adjustable range

0 to 100

Note

• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.

17

Chapter 4 Advanced Adjustment / Setting

●

Contrast

The brightness of the screen is adjusted by varying the video signal level.

Adjustable range

0 to 100

Note

• In the contrast of 50, every color gradation is displayed.

• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the

gradation characteristics, prior to the contrast adjustment.

• Perform the contrast adjustment in the following cases.

- If the image is too dark even when the brightness is set to 100 (Set the contrast to higher than 50.)

●

Temperature

Color temperature can be adjusted.

The color temperature is normally used to express the hue of "White" and / or "Black" by a numerical

value. The value is expressed in degrees "K" (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like

the ame temperature. The gain preset values are set for each color temperature setting value.

Adjustable range

O / 4000 K to 10000 K (specied by every 500 K unit, including 9300 K)

Note

• The value shown in "K" is available only as reference.

• Selecting "Advanced Settings" - "Gain" allows you to perform more advanced adjustment (see “Gain” (page

18)).

• If you set to "O", the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).

• When gain is changed, the color temperature is changed to "O".

●

Gamma

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal,

however, the variation rate is not proportional to the input signal. Maintaining the balance between the

input signal and the brightness of the monitor is called “Gamma correction".

Adjustable range

1.8 / 2.0 / 2.2

Note

• If "sRGB" is selected for the color mode, "2.2" is displayed for the gamma value.

18

Chapter 4 Advanced Adjustment / Setting

●

Advanced Settings

Function Adjustable range Description

Saturation -50 to 50 This function allows you to adjust color saturation.

Note

• Using this function may prevent some color gradations from

being able to be displayed.

• The minimum value (-50) changes the screen to

monochrome.

Hue -50 to 50

This function allows you to adjust hue.

Note

• Using this function may prevent some color gradations from

being able to be displayed.

Overdrive Enhanced / Standard

/ O

This function allows you to set overdrive intensity based on the

use of the monitor.

You can reduce image lags by setting it to "Enhanced" when

displaying animated images.

Note

• The overdrive function is disabled in the following cases:

- When the vertical scan frequency of input signals is more than

70 Hz

- When "Normal" or "Enlarged" is selected from "Screen Size"

(excluding the case that display resolution is 1920 × 1080).

Gain 0 to 100

The brightness of each color component red, green, and blue

is called "Gain". You can change the hue of "white" by adjusting

gain.

Note

• Using this function may prevent some color gradations from

being able to be displayed.

• The value of gain changes with that of color temperature.

• When gain is changed, the color temperature is changed to

"O".

●

Color Reset

Reset any color adjustments for the currently selected color mode back to the default settings.

19

Chapter 4 Advanced Adjustment / Setting

4-3. Screen

For D-Sub signal input For DisplayPort or DVI signal input

●

Screen Size

The image with the resolution other than the recommended resolution is displayed in full screen

automatically. You can change the screen size by using the “Screen Size” function.

Settings Function

Full Screen Displays an image in full screen. Images are distorted in some cases because the

vertical rate is not equal to the horizontal rate.

Enlarged Displays an image in full screen. In some cases, a blank horizontal or vertical

border appears to equalize the vertical rate and the horizontal rate.

Normal Displays images with the specied resolution.

Example: Image size 1024 × 768

Full Screen Enlarged Normal

(1920 × 1080) (1440 × 1080) (1024 × 768)

●

Smoothing

When an image is enlarged with a resolution other than recommended ("Full Screen" or "Enlarged" is

selected in "Screen Size"), the characters or lines of the displayed image may blur. This function

reduces this blurring eect.

Adjustable range

1 to 5

Note

• Smoothing setting may not be required depending on the display resolution. (You cannot choose

"Smoothing".)

20

Chapter 4 Advanced Adjustment / Setting

●

Analog Adjustment

Screen ickering, display position, and size can be adjusted when the D-Sub signal is input.

Function Description

Auto Screen Adjust Screen ickering, display position, and size can be adjusted automatically. Selecting

“Auto Screen Adjust” displays a message. Select “Yes” to enable this function.

Note

• The automatic screen adjustment function works correctly when an image is fully

displayed over the entire displayable area of the screen. They do not work properly

in the below cases:

- When an image is displayed only on a part of the screen (command prompt

window, for example)

- When a black background (wallpaper, etc.) is in use

Also, these functions cannot work properly in some graphic boards.

• When a signal is input into the monitor for the rst time or when a resolution or

vertical / horizontal scan frequency not used before is set, the screen is adjusted

automatically (only for signals with a resolution of 800 × 600 or higher).

Auto Range Adjust Every color gradation (0 to 255) can be displayed by automatically adjusting the signal

output level. Selecting “Auto Range Adjust” displays a message. Select “Yes” to enable

this function.

Clock

Flickering of vertical lines on the screen or part of the screen can be reduced.

Note

• Use to make ne adjustments so as not to miss any adjustment points.

Phase

Flickering and blurring over the entire screen can be reduced.

Note

• Flickering or blurring may not be eliminated depending on your PC or graphics

board.

• After setting, adjust the “Clock” again if vertical bars appear.

Hor. Position

Ver. Position

The display position (horizontal and vertical) of the screen can be adjusted.

Note

• Since the number of pixels and the pixel positions are xed on the LCD monitor,

only one position is provided to display images correctly. The position adjustment is

made to shift an image to the correct position.

Pagina se încarcă...

Eizo FDF2382WT Manual de utilizare

Eizo FDF2382WT Manual de utilizare

în alte limbi

Lucrări înrudite

Alte documente