Ubiquiti UAP-AC-PRO Ghid de inițiere rapidă

Access Point Ubiquiti UniFi

Indoor UAP-AC-PRO

O UniFi é o revolucionário sistema Wi-Fi que combina

desempenho empresarial, escalabilidade ilimitada e um

controlador de gerenciamento central.

O Access Point possui a mais recente tecnologia Wi-Fi

802.11ac, 3x3 MIMO em um design industrial refinado e é

ideal para a implantação de redes sem fio de desempenho

máximo.

www.bztech.com.br

802.11ac Dual-Radio

Pro Access Point

Model: UAP-AC-PRO

Introduction

Thank you for purchasing the Ubiquiti Networks®

UniFi®802.11ac Dual-Radio Pro Access Point. This Quick Start

Guide is designed to guide you through installation and

includes warranty terms.

IMPORTANT: The UAP-AC-PRO requires the UniFi

Controller v5.4 or higher, available at:

www.ubnt.com/download/unifi

Package Contents

UniFi AP AC Pro Mounting Bracket Ceiling Backing Plate

Flat Head Screws

(Qty. 4)

Keps Nuts

(Qty. 4)

Screws

(Qty. 4)

Screw Anchors

(Qty. 4)

Cable Feed Plug Gigabit PoE* (48V, 0.5A)

with Mount Bracket

Power Cord*

* Included only in the single-pack of the UAP-AC-PRO

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall or keyhole saw (to cut 18 mm hole for

Ethernet cable feed)

• Cat5/6 UTP cable for indoor installations

Outdoor Installation Requirements

IMPORTANT: The UAP-AC-PRO may be installed

outdoors under an eave or other protected location. Do

not install the UniFi AP in an open environment.

• Mounting location should be at least 60 cm (2 ft) from the

edge of the eave or ceiling.

• Cable feed opening must be directed away from the open

environment.

• Cable feed must be pointed downwards when wall-mounted.

• Shielded Category 5 (or above) cabling with drain wire

should be used for all outdoor wired Ethernet connections

and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8/10

• Java Runtime Environment 1.8 or above recommended

• Web Browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Controller software v5.4 or newer (available at:

www.ubnt.com/download/unifi)

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A UniFi Cloud Key or management station running the UniFi

Controller v5.4 (or newer) software, located either on-site

and connected to the same Layer-2 network, or off-site in

the cloud or NOC

US-16-150W

USG-PRO-4

(DHCP Server)

Internet

UAP-AC-PRO

UAP-AC-M-PRO

UAP-AC-HD

LAN

WAN

UniFi Cloud Key

(UniFi Controller)

Remote Access too

UniFi Controllerr

Good

Fair

Poor

Great

Network:

Switches

12

Gateway

ধ£-A!ধ32

18%

Internet

Capacity

43%

Clients

412

Guests

113

IoT

45

Everything is

great

My Dashboard

Edit Widgets

-24hrs

Max

980

-2

0

Now

Throughput

Latency

ISP Load:

Great

-24hrs

Max

0

Now

-8ধ1'

-24hrs

High

Low

Now

Retry Rate

Great

Wi-Fi Load:

225.2 Mbps

125.2 Mbps

1

-f-8!ă$-9;8-#<ধ32

36

6

11

40

44

48

52

56

60

64

100

104

108

112

116

120

124

128

132

136

140

149

153

157

161

165

A

WA

Access Points

20

39;$ধ='9

ă$'

Back Room

Storage

Roof

!££>!@'WWW

91 GB

86 GB

53 GB

48 GB

45 GB

3666£-$!ধ329

YouTube

£-'2;9

29;!+8!1

£-'2;9

Squarespace

£-'2;9

33+£'

£-'2;9

Facebook

£-'2;9

Top Interference

ă$'

Roof

Storage

51%

45%

Top CPU Usage

ă$'

Back Room

Home

51%

45%

39;$ধ='£-'2;9

Wi-Fi Key Metrics

£-'2;9

-,32'

¥£-'2;9

2&83-&

£-'2;9

MacBook

£-'2;9

PC Laptop

£-'2;9

iPad

39;$ধ='>-;$,'9

36'138@9!+'

£-'2;8'7<'2$@-9;8-#<ধ32

'=-$'-9;8-#<ধ32

SW-24A

f-;$,'2

SW-8A

f32('8'2$'

SW-8B

Storage

SW-24E

Roof

SW-24D

!££>!@'WWW

56.9%

35.6%

34%

28%

24%

32+'9;£-'2;6ধ1'

-f-<11!8@

3<ধ2+ধ£-A!ধ32

>-;$,<11!8@

iPad-1

692£-2'

!;'>!@f!-2

32;83££'8fă$'

32;83££'8fă$'

¦ধ£-A!ধ32

¦ধ£-A!ধ32

¦ধ£-A!ধ32

2£-2'

MBP-2

£-'2;9

iPad-2

ধ£-A!ধ32

£-'2;9

38;ধ£-A!ধ32

8d 4h 0m

32

24

2d 8h 30m

1,324

2d 8h 30m

64%

1,324

32%

Port Usage

!1'

Status

Users

Guests

Purpose

='8!+'!;!

Port 1- GB

VPN-LA-PDX

21

2

Corporate

320 GB

Port 2 - GB PoE+

VPN-LA-PDX2

6

0

2£@

11 GB

Port 3- 10 GB

'13;'fø$'f

43

0

2£@

12 GB

120

80

32

f32('8'2$'

45%

ă$'f8;'6;

45%

MBP-1

8!ă$

Devices

8!ă$

2d 8h 30m

248 GB

536

1,248 GB

Port 4- GB POE

8!29('8f

7

12

2£@

0 GB

13

0%

100%

Average Capacity

500 Mbps

='8!+'-8ধ1'ধ£-A!ধ32

8%

='8!+'6'$;8!£ă$-'2$@

Wl#c9mA

1300 Mbps

0 Mbps

100%

0%

l#c9mA

W¤l#c9mA

2;'82';322'$ধ32V

30 Mbps

40 Mbps

50 Mbps

20 Mbps

10 Mbps

0 Mbps

-24 hrs

-12 hrs

Now

3>2£3!&

,'38'ধ$!£!6!$-;@

Throughput

Portlan

d

SDN

Last 24 Hrs

A

64% 11ac W2

08% 11n

13 LAN

01 LAN

50%

03 WLAN

28% 11ac

Sample Network Diagram

All UniFi devices support off-site management controllers. For

setup details, see the User Guide on the website:

www.ubnt.com/download/unifi

Hardware Overview

LED

LED Color Status

White Factory default, waiting to be integrated.

Flashing White Initializing.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Quickly

Flashing Blue

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Blue

with Occasional

Flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

Main

Port

Secondary

Port

Security

Slot

Reset

Button

USB

Port

Secondary The Secondary port is a Gigabit Ethernet port used

for bridging.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

USB The USB port is reserved for future use.

Main The Main port is a Gigabit Ethernet port used to

connect the power and should be connected to the LAN and

DHCPserver.

Note: If you need to remove the UniFi AP from the

Mounting Bracket, insert a paper clip in the Security

Slot to release the Lock Tab and turn the UniFi AP

counterclockwise.

Upgrade from UAP-PRO

The design of the UAP-AC-PRO Mounting Bracket facilitates

upgrades from the UAP-PRO, by eliminating the need to drill

new holes in the wall or ceiling tile. The following illustrations

show the Mounting Bracket holes that are used for the

UAP-AC-PRO and UAP-PRO:

Mounting Bracket Holes (4)

for UAP-AC-PRO

Mounting Bracket Holes (3)

for UAP-PRO

To begin the upgrade, perform the following steps:

1. Insert a paper clip into the UAP-PRO Locking Notch

to disengage the lock. Then turn the UAP-PRO

counterclockwise and lift it off of the mounting bracket.

Locking Notch

UAP-PRO (wall mount installation)

2. Unscrew the three screws holding the mounting bracket to

the wall or ceiling tile.

3. Go to step 3 of the Wall Mount section or step 4 of the

Ceiling Mount section.

Hardware Installation

The UniFi AP can be mounted on the wall or ceiling. Perform

the steps for the appropriate installation:

Wall Mount

1. Position the Mounting Bracket at the desired location on

the wall with the Arrow pointing up.

2. Mark the four mounting holes, and use a 6 mm drill bit to

drill the holes. If your Ethernet cable feeds through the

wall, cut or drill a circle approximately 18 mm in diameter.

Then feed the CAT5/6 cable through the hole.

Optional 18 mm Hole for

Ethernet Cable Feed through the Wall

Arrow

3. Insert the Screw Anchors into the 6 mm holes. Secure the

Mounting Bracket to the wall by inserting the Screws into

the anchors.

Note: If upgrading from the UAP-PRO, secure

the new Mounting Bracket to the wall using the

existingholes.

4. Remove the rubber port cover from the UniFi AP.

5. If the Ethernet cable runs along the mounting surface, skip

to step 6. If the Ethernet cable is fed through the wall or

ceiling, insert the Cable Feed Plug.

6. Feed the Ethernet cable through the port cover.

Note: The feed hole will stretch to accommodate the

RJ45 connector, and then seal around the cable.

7. Connect the Ethernet cable to the Main port and replace

the port cover.

8. Align the Notch on the top edge of the UniFi AP with the

Arrow on the Mounting Bracket.

Lock

Tab

Arrow

Notch

9. Rotate the UniFi AP clockwise until the tabs lock into place

and the Lock Tab engages.

Ceiling Mount

1. Remove the ceiling tile.

2. Place the Ceiling Backing Plate in the center of the ceiling

tile. Mark the four mounting screw holes and an 18 mm

hole for the Ethernet cable feed.

18 mm Hole for Ethernet Cable Feed

3. Use a 3 mm drill bit to drill the screw holes, and cut or drill

the hole for the Ethernet cable feed.

4. Insert the Flat Head Screws through the Mounting Bracket,

ceiling tile, and Ceiling Backing Plate (see note below).

Fasten the screws using the Keps Nuts. Then feed the

Ethernet cable through the tile and bracket.

Note: If upgrading from the UAP-PRO, insert the

Flat Head Screws through the new Mounting Bracket,

the ceiling tile, and the Ceiling Backing Plate. (Either

re-use the UAP-PRO Ceiling Backing Plate or replace

it with the new UAP-AC-PRO plate.)

5. Insert the Cable Feed Plug.

6. Remove the port cover from the UniFi AP, and then feed

the Ethernet cable through the port cover.

Note: The feed hole will stretch to accommodate the

RJ45 connector, and then seal around the cable.

7. Connect the Ethernet cable to the Main port and replace

the port cover.

8. Align the Notch on the top edge of the UniFi AP with the

Arrow on the Mounting Bracket.

Lock Tab

Arrow

Notch

9. Rotate the UniFi AP clockwise until the tabs lock into place

and the Lock Tab engages.

10. Set the ceiling tile back into place.

Powering the UniFi AP

The UAP-AC-PRO features auto-sensing 802.3af/802.3at PoE

support and can be powered by any of the following:

• Ubiquiti Networks UniFi Switch with PoE

• 802.3af/802.3at PoE+ compliant switch

• Ubiquiti Networks Gigabit PoE Adapter (48V, 0.5A)

The single-pack of the UAP-AC-PRO includes one Gigabit PoE

adapter. For multi-pack units, PoE adapters or a UniFi Switch

with PoE may be purchased separately.

Connecting to a PoE Switch

Connect the Ethernet cable from the UniFiAP directly to a PoE

port on the switch.

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SFP1

SFP2

Connecting to a PoE Adapter

1. Connect the Ethernet cable from the device to the POE

port of the Gigabit PoE adapter.

2. Connect an Ethernet cable from your LAN to the LAN port

of the Gigabit PoE adapter.

3. Connect the Power Cord to the adapter, and then plug the

Power Cord into a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Software Installation

Download and install the latest version of the UniFi Controller

software. Launch it and follow the on-screen instructions. The

software and step-by-step instructions in the User Guide are

available at: www.ubnt.com/download/unifi

After you have installed the software and run the UniFi

Installation Wizard, a login screen will appear for the UniFi

Controller management interface. Enter the Admin Name and

Password that you created and click Log In.

You can manage your wireless network and view network

statistics using the UniFi Controller management interface.

For information on configuring and using the UniFi Controller

software, refer to the User Guide.

Mobile App Installation

Ubiquiti Networks also offers the UniFi mobile app, which

is available from the App Store® (iOS) or Google Play

™

Store

(Android). You can use it to provision a UniFi AP for basic

functionality without configuring a UniFi Controller. It also

allows seamless provisioning of APs for remote controllers

(controllers not on the same Layer 2 network) and easy access

to local controllers and those monitored on unifi.ubnt.com

Specifications

UAP-AC-PRO

Dimensions 196.7 x196.7 x 35 mm

(7.74 x 7.74 x 1.38")

Weight

with Mounting Kit

350 g (12.35 oz)

450 g (15.87 oz)

Networking Interface (2) 10/100/1000 Ethernet Ports

Buttons Reset

Power Method PoE 802.3af/802.3at

Power Supply 48V, 0.5A Gigabit PoE Adapter*

Max. Power Consumption 9W

Operating Frequency 2.4 GHz

5 GHz

Max. TX Power

2.4 GHz

5 GHz

22 dBm

Antennas (3) Dual-Band Antennas, 3 dBi each

Wi-Fi Standards 802.11 a/b/g/n/ac

Wireless Security WEP, WPA-PSK,

WPA-Enterprise (WPA/WPA2, TKIP/AES)

Mounting Wall/Ceiling (Kits Included)

Operating Temperature -10 to 70° C (14 to 158° F)

Operating Humidity 5 to 95% Noncondensing

Certications CE, FCC, IC

* Included with the single-pack of the UAP-AC-PRO

Pagina se încarcă ...

Ubiquiti UAP-AC-PRO Ghid de inițiere rapidă

Ubiquiti UAP-AC-PRO Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente