Ubiquiti Networks UAP-AC-M Manual de utilizare

802.11ac Indoor/Outdoor AP

with Plug & Play Mesh

Model: UAP-AC-M

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®

802.11ac Indoor/Outdoor Access Point with Plug & Play Mesh

Technology. This Quick Start Guide is designed to guide you

through installation and includes warranty terms.

IMPORTANT: The UAP-AC-M requires the UniFi

Controller v5.4 or higher, available at:

www.ubnt.com/download/unifi

Package Contents

UniFi AC Mesh Antennas (Qty. 2) Wall Mount Bracket

Screws

(Qty. 2)

Screw Anchors

(Qty. 2)

Zip Ties

(Qty.2)

Fast-Mount

Adapter

802.11AC Indoor/Outdoor AP

with Plug & Play Mesh

Model: UAP-AC-M

Gigabit PoE (24V, 0.5A)

with Mount Bracket*

Power Cord* Quick Start

Guide

* Gigabit PoE and Power Cord are not included with UAP-AC-M 5-Pack

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• Wall-mounting: Drill and 6 mm drill bit

• Phillips screwdriver

• Shielded Category 5 (or above) cabling with drain wire

should be used for all outdoor wired Ethernet connections

and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP, one near the UAP-AC-M and the other at the

entry point to the building. The ETH-SP will absorb power

surges and safely discharge them into the ground.

To LAN

ETH-SP

US-8-150W

UAP-AC-M

Diagram Showing Use of Ethernet Surge Protectors

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8/10

• Java Runtime Environment 1.6 (1.8 or newer recommended)

• Web Browser: Google Chrome (Other browsers may have

limited functionality)

• UniFi Controller software v5.4 or newer (available at:

www.ubnt.com/download/unifi)

Wireless Adoption Requirements

The UAP-AC-M supports wireless adoption into your UniFi

Wi-Fi network. This feature requires a currently managed

UniFiAP operating with the following configuration:

• The UniFi AP must be running firmware 3.7.7 or newer

• At least one SSID enabled and operating on 5 GHz band

• The UAP-AC-M must be within wireless range of the UniFi AP

Network Topology Requirements

• A DHCP-enabled network (for the UniFi device to obtain an IP

address as well as for the wireless clients after deployment)

• A UniFi Cloud Key or management station running the UniFi

Controller v5.4 (or newer) software, located either on-site

and connected to the same Layer 2 network, or off-site in the

cloud or NOC

US-16-150W

USG-PRO-4

(DHCP Server)

Internet

UAP-AC-PRO

UAP-AC-M

LAN

WAN

UniFi Cloud Key

(UniFi Controller)

Remote Access to

UniFi Controller

Sample Network Diagram

All UniFi devices support off-site management controllers.

For setup details, see the User Guide on the website:

www.ubnt.com/download/unifi

Hardware Overview

LED

Status LED

Port Cover

Front Right Side

LED Color Status

Flashing White Initializing.

Steady White Factory default, waiting to be integrated.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Quickly Flashing

Blue

Used to locate and identify a UniFi device.

When the Locate feature is activated in

the UniFi Controller software, the Status

LED will flash blue. It will also display the

location of the device on the map.

Steady Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Steady Blue

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

Ethernet

Port Reset

Button

Cable

Grommet

Ethernet The Ethernet port is a Gigabit PoE port used to

connect the power and should be connected to the LAN and

DHCP server. Power can be provided by one of the following:

• Gigabit PoE adapter (included)

• Ubiquiti Networks UniFi Switch with PoE

• 802.3af PoE compliant switch

Note: The UAP-AC-M supports 802.3af/A PoE and 24V

Passive PoE. It does NOT support 802.3af/B PoE and

therefore does not work with 802.3af/B switches.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds until the Status LED

turns off.

Hardware Installation

The UniFi AP can be mounted on a wall, pole, or fast-mount

of a Ubiquiti high-gain antenna. Perform the steps for the

appropriate installation:

Wall Mount

To mount the UniFi AP on a wall, use the included Wall Mount

Bracket, Screws, and Screw Anchors.

1. Place the Wall Mount Bracket at the desired location on the

wall in the orientation shown below.

2. Ensure the level is plumb and mark the two screw holes

on the wall.

3. Drill out the holes using a 6 mm drill bit.

4. Insert a Screw Anchor into each hole.

5. Secure the Wall Mount Bracket with two Screws.

6. Attach the UniFi AP to the Wall Mount Bracket by sliding the

mounting tabs into the channel slots until it locks into place.

Pole Mount

To mount the UniFi AP on a pole, use the included Zip Ties:

1. Insert a Zip Tie through the slot of the mount bracket on

the back of the UniFi AP.

2. Position the UniFi AP at the desired location on the pole

and then fasten the Zip Tie around the pole. Fasten the

second Zip Tie in the same manner.

Fast-Mount

The included Fast-Mount Adapter allows the UniFi AP to be

mounted on a Ubiquiti high-gain antenna equipped with a

fast-mount radio mounting bracket.

1. Attach the Fast-Mount Adapter to the fast-mount by sliding

the four mounting tabs into the corresponding channel

slots until it locks into place.

2. Mount the UniFi AP to the Fast-Mount Adapter.

Attach Antennas

1. Remove and discard the two black boot covers. Ensure the

Rubber Gaskets remain in place.

Rubber

Gaskets

2. Connect the Antennas to the RP-SMA connectors.

Note: For optimal performance, it is recommended to

position the Antennas at 45-degree angles.

*640-00244-04*

640-00244-04

Powering the UniFi AP

1. Slide the Port Cover down to remove it.

2. Remove the Cable Grommet. Slide an Ethernet cable

through the Cable Grommet and connect the cable to the

Ethernet port. Make the necessary adjustments to ensure

that the Cable Grommet is securely back in place, and then

replace the Port Cover.

Connecting to a PoE Adapter

1. Connect the Ethernet cable from the UniFi AP to the POE

port of the Gigabit PoE adapter.

2. (Optional for non-mesh setup) Connect an Ethernet cable

from your LAN to the LAN port of the Gigabit PoE adapter.

3. Connect the Power Cord to the adapter, and then plug the

Power Cord into a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the slots on the adapter with the tabs of the PoE

Mounting Bracket, and then slide the adapter down.

Connecting to a PoE Switch

Connect the Ethernet cable from the UniFi AP directly to a PoE

port on an 802.3af switch. PoE will automatically be enabled.

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SPF1

SPF2

Connected to UniFi Switch, model US-24-250W

Note: The UAP-AC-M supports 802.3af/A PoE and 24V

Passive PoE. It does NOT support 802.3af/B PoE and

therefore does not work with 802.3af/B switches.

Wireless Adoption

See the Wireless Adoption Requirements section before

proceeding.

1. Ensure the UniFi AP is powered on, and then launch the

UniFi Controller software.

2. Go to the Devices page, and the UAP-AC-M will show up as

Pending Adoption (Wireless).

3. Click Adopt.

For information on configuring and using the UniFi Controller

software, refer to the User Guide located on our website:

www.ubnt.com/download/unifi

Software Installation

Download and install the latest version of the UniFi Controller

software. Launch it and follow the on-screen instructions. The

software and step-by-step instructions in the User Guide are

available at: www.ubnt.com/download/unifi

After you have installed the software and run the UniFi

Installation Wizard, a login screen will appear for the UniFi

Controller management interface. Enter the Username and

Password that you created and click Log In.

You can manage your wireless network and view network

statistics using the UniFi Controller management interface.

For information on configuring and using the UniFi Controller

software, refer to the User Guide.

Mobile App Installation

Ubiquiti Networks also offers the UniFi mobile app, which

is available from the App Store (iOS) or Google Play™ Store

(Android). You can use it to provision a UniFi AP for basic

functionality without configuring a UniFi Controller. It also

allows seamless provisioning of APs for remote controllers

(controllers not on the same Layer 2 network) and easy access

to local controllers and those monitored on unifi.ubnt.com

Specifications

UAP-AC-M

Dimensions 353 x 46 x 34.4 mm

(13.9 x 1.81 x 1.35")

Weight 152 g (5.36 oz) with Antennas

Networking Interface (1) 10/100/1000 Ethernet Port

Buttons Reset

Power Method 24V Passive PoE (Pairs 4, 5+; 7, 8 Return);

802.3af Alternative A (Pairs 1, 2+; 3, 6 Return)

Power Supply 24V, 0.5A Gigabit PoE Adapter (Included)

Supported Voltage Range 44 to 57VDC

Power Save Supported

Max. Power Consumption 8.5W

Max. TX Power

2.4 GHz

5 GHz

20 dBm

Throughput Speeds*

2.4 GHz

5 GHz

300 Mbps

866.7 Mbps

Range* 183 m (600 ft)

Antennas (2) External Dual-Band Omni Antennas

Antenna Gain

2.4 GHz

5 GHz

3 dBi

4 dBi

Wi-Fi Standards 802.11a/b/g/n/ac

Wireless Security WEP, WPA-PSK,

WPA-Enterprise (WPA/WPA2, TKIP/AES)

BSSID Up to Four per Radio

Mounting Wall/Pole/Fast-Mount (Kits Included)

Operating Temperature -30 to 70° C (-22 to 158° F)

Operating Humidity 5 - 95% Noncondensing

Certications CE, FCC, IC

* Speed and Range values may vary and are based on optimal environments.

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Pagina se încarcă ...

Ubiquiti Networks UAP-AC-M Manual de utilizare

Ubiquiti Networks UAP-AC-M Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente