Smithco Sand Star Zee Instrucțiuni de utilizare

Marca: Smithco

Model: Sand Star Zee

Tip: Instrucțiuni de utilizare

Sand Star Zee

Model 45-501-A

March 2018

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

Operator’s

Introduction Service Diagrams

CONTENTS

Introduction ......................................................1-10

Introduction ........................................................................................ 1

Symbols ..........................................................................................2-3

Safety ...............................................................................................4

Warning Decal ...................................................................................5

Safe Practices ...................................................................................6

Specications ....................................................................................7

Setup ..............................................................................................8-9

Controls & Instruments ...................................................................10

Service ............................................................ 11-19

Operation .................................................................................... 11-14

Daily Checklist .................................................................................14

Service Charts ............................................................................15-16

Battery .............................................................................................17

Quick Hitch ......................................................................................18

How to rake a Sand Trap ................................................................. 18

45-501 Wiring Schematic ................................................................19

Hydraulic Schematic ........................................................................ 19

Other ...............................................................21-23

CE Declaration ...........................................................................21-22

Quick Reference .............................................................................. 23

Limited Warranty ..................................................................................

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

INTRODUCTION

Thank you for purchasing a Smithco product.

Read this manual and all other manuals pertaining to the Sand Star Zee carefully as they contain safety, op-

erating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment

damage.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides

are from the operator’s seat, facing forward.

All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. Refer to engine manual for placement of engine serial number.

For product and accessory information, help nding a dealer, or to register your product please contact us at

www.Smithco.com.

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts

For easy access record your Serial and Model numbers here.





WARNING

Failure to follow cautious operating practices

can result in serious injury to the operator or

other persons. The owner must understand

these instructions, and must allow only trained

persons who understand these instructions to

operate this vehicle.

WARNING:

Engine exhaust and some of its constituents are

known to the State of California to cause cancer,

birth defects, and other reproductive harm.

For more information visit

www.P65Warning.ca.gov

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

20° MAX

Read Operator’s

Manual

Engine Stop

Engine Start

Engine Run

Engine Oil

Water

Temperature

RPM

Gasoline

Diesel

Glow Plug

Hour Meter

Hand Throttle

Choke

Hydraulic

Oil Level

Ground Speed

Park Brake

Release

Lift Arm

Slow

Moving Parts

Pinch Point

Hydraulic Fluid

Penetration

Warning

Danger

Caution

Fast

Rollover

Danger

Hot Surface

Headlamp

Seat Belt

No Riders

Blower

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY

Read and understand this manual and all safety signs before operating and maintaining. Review

the safety instructions and precautions annually.

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED

TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND

THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN

INJURY OR DEATH.

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety

messages. The appropriate signal word for each has been selected using the following

guidelines:

DANGER: Red. Indicates an imminently hazardous

situation that, if not avoided, will result in death or

serious injury. This signal word is to be limited to

the most extreme situations typically for machine

components which, for functional purposes, cannot

be guarded.

WARNING: Orange. Indicates a potentially

hazardous situation that, if not avoided, could result

in death or serious injury, and includes hazards that

are exposed when guards are removed. It may also

be used to alert against unsafe practices.

CAUTION: Yellow. Indicates a potentially hazardous

situation that, if not avoided, may result in minor or

moderate injury. It may also be used to alert against

unsafe practices.

IMPORTANT: Blue. Indicates procedures which

should be

followed to avoid damage to the machine.

Safety

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY WARNING DECALS

REMEMBER: If Safety Signs have been damaged, removed, become illegible or parts replaced

without decals, new decals must be applied. New decals are available from your authorized

distributor or factory.

This is a list of decals located on the Sand Star Zee. Part number, description and location will help in

reordering decals.

A 13-063 Decal, Warning

25-357 Decal, Smithco

25-369 Decal, 84 dBA

B 25-277 Decal, Battery

C 25-286 Decal, Pinch Point

D 25-298 Decal, Warning Hot

E 45-522 Decal Sand Star Zee

F 25-354 Decal, Tire Pressure 5psi

G 25-356 Decal, Tire Pressure, 20 psi

H 45-524 Decal, Control Panel

I 51-184 Decal, Park Brake

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine (engine,

accessories and attachments).

2. Never allow anyone to operate or service the machine or its attachments without proper training and

instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all Personal Protective Equipment (PPE) on your head, eyes, ears, hands and feet. Operate the

machine only in daylight or in good articial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can nd before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without

proper ventilation.

9. Fuel is highly ammable, handle with care. When lling tank stop 1 inch(2.54 cm) from top. Leave room

for expansion. DO NOT OVERFILL.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. After engine has started machine must not move. If movement is evident, the neutral mechanism is not

adjusted correctly. Shut engine off and readjust so the machine does not move when in neutral position.

13. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and

cause serious injury.

14. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not stop or start suddenly on any slope.

C. Do not drive on slopes greater than 10°.

D. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.

E. Stay alert for holes in the terrain and other hidden hazards.

15. Before leaving operator’s position for any reason:

A. Disengage all drives.

B. Lower all attachments to the ground.

C. Set park brake.

D. Shut engine off and remove the ignition key.

16. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

17. Keep the area of operation clear of all bystanders.

18. Never carry passengers.

19. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

20. Use parts and materials supplied by Smithco only. Do not modify any function or part.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAND STAR ZEE SPECIFICATIONS

WEIGHTS AND DIMENSIONS

Length 75" (1,91 m)

Width 59" (1,50 m)

Height 70" (1,78 m)

Wheel Base 48" (1,22m)

Ground Clearance 5.5" - 7" (13 -18 cm) - under cultivator depending on attachment

Weight 880 lbs. (399 kg)

SOUND LEVEL

At Ear Level 82 dB

ENGINE

Make Briggs and Stratton Commercial Turf

Model# 44T677

Type / Spec# 0001G1

Horsepower 22HP (16.4 kW)

Fuel Unleaded 87 Octane Gasoline Minimum

Lubrication System Full Pressure

Alternator 16 amp

WHEELS & TIRE

5 psi (.34 bar) Two: 25 X 10 - 12 Rear Knobby Tire

20 psi (1,38 bar) One: 16 x 7.50 - 8 Front Castor

SPEED

Forward Speed 0 to 10 m.p.h. (0-16 kph)

Reverse Speed 0 to 4 m.p.h. (0-6 kph)

BATTERY Automotive Type SP 35

BCI Group Size 35

Cold Cranking Amps 375

Ground Terminal Polarity Negative (-)

Maximum Length 7.5" (19 cm)

Maximum Width 5" (12,7 cm)

Maximum Height 7.5" (19 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 20 quarts (18,93 liters)

Hydraulic Fluid 7 quarts (6,6 liters)

Grade of Hydraulic Fluid Parker Dura Clean Hydraulic Oil or Equivalent of AW32 minimum hydraulic

oil

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP ASSEMBLY

The Sand Star Zee arrives from Smithco with some assembly required before service.

REAR WHEEL MOUNTING

1. Set park brake. Push the brake down past center and the park brake is engaged.

2. Block front tire. Jack up rear of machine being careful not to damage underside of machine. Place

wheel on hub lining up bolt holes. Use the ten lug nuts provided. Then torque to 64 - 74 ft/lb (87-100

Nm) using a cross pattern. Retorque after the rst 10 hours and every 200 hours thereafter. Lower ma-

chine to ground and remove blocks and jack.

3. Check the tire pressure. The rear knobby tire pressure should be 5 psi (0.34 bar). The front caster

wheel should be 20psi (1.38 bar).

REAR HITCH LIFT ARM

1. You will need the

clevis and bridge pin from the hard-

ware bag.

2. The rear hitch lift arm is slid into the hitch on the back of

the machine between the adjustment bolts and held in

place with the

clevis and bridge pin .

3. Be sure hitch lift arm is on top of the hitch lift bar and the

lock and spring are on the top.

SEAT

1. Place the seat on the seat frame spacers.

2. Plug in seat switch.

3. Use four

whiz locks nuts from the hardware bag to secure

seat to the seat spacers. Tighten all bolts.

ROLL BAR

1. Mount the roll bar on the main frame just behind seat. There

are 2 mounting plates with four holes in them. Use eight 7/16

bolt, washer and lock nut, four on each side.

2. Roll bar should be leaning towards the back of the machine.

RAKE HOLDER

1. The rake holder is mounted on the right hand side of

the roll bar.

2. Measure up 7" from the roll bar mounting plate.

3. Use a u-bolt from the small parts bag to hold the rake

holder in place. Tighten all hardware.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP ASSEMBLY

BATTERY BOX

1. Battery box is mounted on the left hand side of the roll bar.

2. Measure up 5

" from the roll bar mounting plate.

3. Use a u-bolt from the small parts bag to hold the battery box in

place. Tighten all hardware

4. Battery not furnished. Install an automotive type SP 375 cold

cranking amps (minimum) battery in the battery box of the

Sand Star Zee. This is a negative grounding system. Attach

the rubber battery (C) hold-down found in the small parts bag.

Then attach red positive (+) cable (A) to positive terminal. Slide

rubber boot over the positive terminal to prevent shorts. Attach

black negative (-) cable (B) to the negative terminal.

Connecting battery cables to the

wrong post could result in personal injury and/

or damage to the electrical system. Make sure

battery and cables do not interfere or rub on any

moving part. Connect the red positive (+) cable

(A) to the battery rst. When disconnecting remove the black

negative (-) cable (B) rst.

FUEL , HYDRAULIC OIL AND GREASE FITTINGS

1. Check engine oil and add as necessary. See engine manual for recom-

mended motor oil. DO NOT OVERFILL.

2. Fill Gas Tanks with Unleaded 87 Octane gasoline (minimum).When lling

the fuel tank stop when the fuel reaches 1 inch (2.54cm) from the top.

This space is necessary for fuel expansion. DO NOT OVERFILL.

Fuel is ammable. Caution must be used when storing or handling it. Do not ll fuel

tank while engine is operating or in an enclosed area. Fumes are explosive and dan-

gerous to inhale. DO NOT SMOKE while lling the fuel tank. DO NOT OVERFILL.

The engine and exhaust system become very hot during operation. Rick of burns if

touched. Allow engine and exhaust system to cool before refueling.

3. Check hydraulic oil level in the tank reservoir. The level should be

1-3" from

the bottom of the dipstick. If level is low add

Parker Dura Clean Hydraulic Oil or equivalent of

AW32 minimum hydraulic oil.

4. Machine should be greased before starting. Use

general purpose No. 2 lithium base grease.

A. Rear attachment lift yoke.

B. Right attachment lift mount.

C. Left attachment lift mount.

D. Center attachment lift yoke.

E. Center lift lever.

F. Front fork.

5. Read operating instructions before starting ma-

chine.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

A. Motion Control Levers - Two continuously variable control levers that move forward or backward

about a neutral position.

B. Center Lift Lever - Pull inward to release. Spring loaded back into lock position. Works in combina-

tion with left foot pedal.

C. Park Brake - Lift up to engage. Push down to disengage.

D. Center Lift Pedal - Push down to lift center attachment. Used in conjunction with center lift adjust-

ment lever.

E. Seat Adjustment - Lever below seat to move seat forward or back.

F. Manual Rear Attachment Lift Pedal /Lift Lever - used to lift and lower rear attachment manually.

G. Choke - Pull choke control knob up to close choke plate when starting a cold engine. A warm en-

gine may not require "choking" to start.

H. Ignition Switch - The ignition switch has three positions: Off-Run-Start.

I. Oil Light - The oil light should come on when ignition is on without engine operating. The oil light

will light when the oil pressure is low. If oil light should come on, shut off engine immediately and

nd the cause.

J. Hand Throttle - The hand throttle is used to regulate engine speed.

K. Hour Meter - The hour meter indicates hours of machine operation. It operates only when the igni-

tion switch is on.

L. Light - (OPTIONAL) This is a holder for rocker switch to turn on and off lights.

M. Rake Holder - used to carry hand rake.

N. Cup Holder - Cup holder for large cup.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

STARTING ENGINE

Before operating this machine, become familiar with all controls and functions

of these units. Also complete all maintenance requirements and read all safety

warnings. By knowing the machine thoroughly, how it operates and by doing the

prescribed maintenance steps, you can expect relatively trouble-free operation for

years to come.

1. Set park brake. Start safety switch is on the park brake.

2. The ignition switch is a three position on gas and four position on diesel.

Insert key (A) and turn clockwise until engine starts (C). Release key and it

will return to run position (B). Use choke and hand throttle as necessary.

3. Allow engine to idle and warm up a few minutes before selecting a direction

of travel.

4. To shut off engine on all gas machines turn key to the stop position.

STEERING CONTROL LEVERS

Acquaint yourself with the steering before operating the machine. This machine is equipped with two steering

control levers (A) that make the machines speed and direction continuously variable. The steering controls

can be moved forward or backward about a neutral position. The neutral position is locked when the steering

control levers are moved outward and the machine will stand still.

Move in a straight line - By moving both controls an equal amount forward or backward, the machine will

move in a straight line forward or backward respectively.

To turn right while going forward - Move right control lever towards the neutral position. This will cause the

rotation of the right wheel to reduce which will result in the machine turning to the right.

To turn left while going forward - Move left control lever towards the neutral position. This will cause the

rotation of the left wheel to reduce which will result in the machine turning to the left.

Zero Turn - Zero turn can be achieved by moving one control lever backward, behind neutral position, and

carefully moving the other control lever forward from its neutral position. The rotation direction is deter-

mined by the control lever that is moved backward behind the neutral position. If left control lever is

backward, machine will turn left. If right control lever is moved backward, machine will turn right.

The machine can move rapidly if one steering control is moved much further

than the other.

Reverse Neutral Forward Right Zero Turn

Do not drive up and down hills with slopes greater than 10°. Do not drive

across slopes.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

CENTER LIFT

Using the foot pedal on the left oorboard and the center lift lever you

can raise and lower the center lift. To lift, push right foot pedal all the

way down and the center lift lever will lock into place. To lower, place

pressure on the foot pedal, place detent pin in hole for correct depth

you are trying to obtain, push center lift lever inward and release ped-

al. Detent pin will stop center lift at selected depth.

ELECTRIC/HYDRAULIC REAR LIFT (45-501)

To lift and lower the rear attachments on the 45-501, use the rocker switch on the right control lever. Pushing

the switch up will raise the rear attachment. Pushing the rocker switch down will lower the rear attachment.

Rear Electric Lift

Rocker Switch

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

PARK BRAKE

The park brake is located on the left side of the machine and operates the brakes on the rear wheels. Push

lever forward to disengage and pull back to engage.

To adjust turn the knob on the end of the handle. For further adjustment you may turn the yokes clockwise to

tighten and counter clockwise to loosen.

ADJUSTMENT OF BELT TENSIONER

The belt tensioner controls the tension on the belt from

the engine to the left and right hydro units. The proper

tension of the idler should be in the third notch on the

side of the tensioner. Over tightening the belt will shorten

the life of the belt and the machine may not perform to

the best of its ability. To adjust belt tensioner, loosen the

bolt holding the tensioner. Bring idler pulley tight to the

belt and turn tensioner into belt to the third notch. Us-

ing a pair of channel lock pliers, rotate the upper half of

the tensioner clockwise until the indicator is at the third

notch. Tighten bolt on tensioner.

SPEED BOSS ADJUSTMENT (45-501 SERIAL NO. ZTR001-ZTR092)

The Speed Boss can be adjusted on either end of the speed boss cable. Tighten or loosen the yoke or ball

joint to get desired down pressure. Make adjustment with the actuator in the lifted up position. Check down

pressure before continuing.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

ENGINE

Change and add oil according to chart below. Do not overll. Engine oil capacity is 2 quarts. We recommend

high-quality detergent oils classied for service SF, SG, SH, SJ or higher. Do not use special additives. Out-

door temperatures determine the proper oil viscosity for the engine. Use the chart to select the best viscosity

for the outdoor temperature range expected.

SAE VISCOSITY GRADES

Use of multi-viscosity oils (10W-30, etc.) above 80° F (27° C) will result in high oil consumption and possible

engine damage. Check oil level more frequently if using these types of oils.

SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to

inadequate lubrication.

DAILY CHECKLIST

Use all procedures and ONLY use parts prescribed by the manufacturer. Read

the engine manual before operation.

Before servicing or making adjustments to the machine, stop engine, set park

break, block wheels and remove key from ignition.

DAILY CHECKLIST

1. Check park brake adjustment. Adjust as required.

2. Check engine oil level. Add as needed. DO NOT OVERFILL.

3. Tire pressure should be 5 psi (0.34 bar) maximum on rear tires and 20 psi (1.38 bar) on the front tire.

4. Inspect electrical system for loose connections or frayed wiring, including battery cables. Replace any

faulty equipment or tighten if loose.

5. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.

6. Inspect hydraulic lines for damage or leaks. Never use hands to inspect leaks.

7. Check hydraulic oil level on the tank. The level should be

1-3" from the bottom of the dipstick. If level is

low ll with Parker Dura Clean Hydraulic Oil or Equivalent of AW32 minimum hydraulic oil.

8. Inspect steering control levers, throttle and shift linkages for good hookups and clear travel.

9. Check controls for smooth, proper working operation.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SERVICE CHART

The suggested maintenance checklist is not offered as a replacement for the manufacturer’s engine manual

but as a supplement. You must adhere to the guidelines established by the manufacturer for warranty cover-

age. In adverse conditions such as dirt, mud or extreme temperatures, maintenance should be more frequent.

Maintenance Service Interval

Maintenance Procedure

After the first 8 operating hours

• Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))

• Change the engine oil filter.

Before each use daily

• Check the engine oil level.

• Clean area around muffler and controls

• Check the hydraulic fluid level.

• Check the tire pressure.

• Check condition of hydraulic hoses and fittings.

• Inspect and clean the machine.

Every 25 hours

• Clean air filter

• Check the battery fluid level and cable connections.

• Change oil when operating under heavy load or high

ambient temperatures.

Every 50 hours

• Replace engine oil filter

• Check muffler and spark arrestor

Every 100 hours

• Replace engine oil filter

Every 250 hours

• Change air filter

• Check tire pressure (5 psi)-Rear. 20 psi - Front.

• Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))

• Change hydrauilic oil and filter

• Lubricate machine

Every 400 hours or yearly

• Replace air filter

• Replace Pre Cleaner

• Replace spark plugs

• Clean air cooling system

• Replace fuel filter

• Check valve clearance

• Lubricate machine

• Visual inspection of machine and hydraulic hoses

• Change oil

• Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))

• Check battery terminals and electrolyte level

In dusty conditions or when airborne debris is present, clean more often

Not required unless engine performance problems are noted.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

MAINTENANCE SERVICE CHART

Duplicate this page for routine use. Service

Clean more often under dusty conditions or when airborne debris is present , replace air cleaner parts, if very

dirty.

Maintenance Check Item For the week of:

Mon Tues. Wed. urs. Fri. Sat. Sun.

Check the Safety Seat Switch

Check Steering Operation

Check the fuel level

Check the engine oil level.

Clean the air lter

Clean the engine cooling ns.

Check for unusual engine noises

Check the hydraulic oil level

Check hydraulic hoses and ttings for

damage

Check for uid leaks.

Check the tire pressure

Check the Instrumentation

Inspect electrical system for frayed wires

Check park brake adjustment

Change oil lter.

Change oil.

Lubricate Machine

Ensure all warning decals are intact.

Areas of Concern

Inspection Performed by:

Item Date Information

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or

any ignited object to come near the battery. When charging or working near battery, always shield your eyes

and always provide proper ventilation.

Battery cable should be disconnected before using "Fast Charge".

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended

charging rate. If electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp rst and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If

electrolyte is splashed on any part of your body, ush all contact areas imme-

diately with liberal amounts of water. Get medical attention immediately.

JUMP STARTING

Use of booster battery and jumper cables. Particular care should be used

when connecting a booster battery. Use proper polarity in order to prevent

sparks.

To jump start (negative grounded battery):

1. Shield eyes.

2. Connect ends of one cable to positive (+) terminals of

bottom post on solenoid rst (A), then positive post of

booster battery. (B).

3. Connect one end of other cable to negative (-) terminal of

booster battery (C).

4. Connect other end of cable (D) to engine block on unit

being started.

To prevent damage to other electrical components on unit being

started, make certain that engine is at idle speed before discon-

necting jumper cables.



Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

QUICK HITCH

Bunker Rakes are tted with a Quick Hitch Accessory Mount System. On each mount is a spring loaded locking

mechanism and a lock pin. Remove the lock

pin and push down on the spring loaded locking

mechanism and your rear attachment will pull

off, so you can easily switch out attachments.

The lock pin acts as a safety device to keep

lock pin from opening up when crossing rough

terrain.

There are also adjustment screws on the Quick

Hitch Accessory Mount System that may need to

be adjusted for certain rear attachments. These

allow the rear attachment to move from side to

side without touching the rear wheels. Please

see instructions on each individual attachment

that you purchase.

Run machine and test for operation of the rear

attachment by raising and lowering the assem-

bly and with the attachment down turn sharp

corners in both directions to ensure rake is not

contacting the tires.

HOW TO RAKE A SAND TRAP

View bunker to determine the

most efcient pattern to fol-

low so that rake pattern and

conguration of bunker will

ow in same general direction

and look attractive.

Enter bunker at its lowest

point. Perhaps drain area or

another point where “lip” of

the trap is minimal.

Operate at 2-4 m.p.h. (3-6.5

kph) for best raking results.

Control speed with hydraulic

pedal.

Once fully inside bunker,

lower rear rake and proceed

forward as described above.

First pass should be directly down center of trap. This helps avoid extremely sharp turns that will spoil sands’ appearance.

Once at far end, turn machine and drive down one side of trap and come back up other side.

Grass or other material may build up on rake tines as machine passes “enter/exit” point in Figure 1. Lift rake briey while

still moving forward.

Do not rake closer than 6" (15 cm) to edge of trap.

Do not rake slopes in trap. The weight of machine will pull sand down.

Use cultivator or other center mounted accessories only as necessary for compacted sand. Frequent use will leave sand

too soft and objectionable to some golfers.

Use front mounted plow to push sand to desired locations within trap.

After exiting trap, secure machines in accordance with practices described in this manual. Rake trap edges, slopes and

“enter /exit” area with a hand rake.

After returning to maintenance area, thoroughly clean machine, check uids, and lubricate as advised in this manual.

Adjustment Screws

Spring Loaded

Locking

Mechanism

Diagrams

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

45-501 GOLF ZTR WIRING SCHEMATIC

HYDRAULIC SCHEMATIC

Pagina se încarcă ...

Smithco Sand Star Zee Instrucțiuni de utilizare

Marca: Smithco

Model: Sand Star Zee

Tip: Instrucțiuni de utilizare

Descărcați PDF

raport

în alte limbi

English: Smithco Sand Star Zee Operating instructions
eesti: Smithco Sand Star Zee Kasutusjuhend

Smithco Sand Star Zee Instrucțiuni de utilizare

Smithco Sand Star Zee Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente