Smithco Sand Star Instrucțiuni de utilizare

Marca: Smithco

Model: Sand Star

Categorie: Accesorii pentru autovehicule

Tip: Instrucțiuni de utilizare

Sand Star I-II-III-IV-V

Model 45-001 2WD Chain Steering

Model 45-002 3WD Chain Steering

Model 45-003 3WD Hydraulic Steering

Model 45-204 3WD Series Parallel

Model 45-205 3WD Diesel

January 2017

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

Operator’s

Introduction Service Reference

CONTENTSroductin 1-11

Introduction ...................................................... 1-11

Introduction ........................................................................................ 1

Symbols .............................................................................................2

Safety ...............................................................................................3

Warning Decal Location .....................................................................4

Safe Practices ...................................................................................5

Specications ................................................................................6-7

Setup .................................................................................................8

Controls & Instruments ................................................................9-11

Service ............................................................ 11-18

Operation .................................................................................... 11-12

Daily Checklist .................................................................................13

Service Charts ............................................................................14-16

How To Rake A Sand Trap ..............................................................17

Quick Hitch ......................................................................................17

Battery .............................................................................................18

Reference .......................................................20-25

Declaration of Conformity ...........................................................20-25

Quick Reference .............................................................................. 26

Limited Warranty ..................................................................................

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

INTRODUCTION

Thank you for purchasing a Smithco product.

Read this manual and all other manuals pertaining to the Bunker Rake carefully as they contain safety, oper-

ating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment

damage.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides

are from the operator’s seat, facing forward.

All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. Refer to engine manual for placement of engine serial number.

For product and accessory information, help nding a dealer, or to register your product please contact us at

www.Smithco.com.

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts

For easy access record your Serial and Model numbers here.





WARNING

Failure to follow cautious operating practices

can result in serious injury to the operator or

other persons. The owner must understand

these instructions, and must allow only trained

persons who understand these instructions to

operate this vehicle.

WARNING:

Engine exhaust and some of its constituents are

known to the State of California to cause cancer,

birth defects, and other reproductive harm.

For more information visit

www.P65Warning.ca.gov

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

20° MAX

Read Operator’s

Manual

Engine Stop

Engine Start

Engine Run

Engine Oil

Water

Temperature

RPM

Gasoline

Diesel

Glow Plug

Hour Meter

Hand Throttle

Choke

Hydraulic

Oil Level

Ground Speed

Park Brake

Release

Lift Arm

Slow

Moving Parts

Pinch Point

Hydraulic Fluid

Penetration

Warning

Danger

Caution

Fast

Rollover

Danger

Hot Surface

Headlamp

Seat Belt

No Riders

Blower

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY

Read and understand this manual and all safety signs before operating and maintaining. Review

the safety instructions and precautions annually.

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED

TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND

THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN

INJURY OR DEATH.

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety

messages. The appropriate signal word for each has been selected using the following

guidelines:

DANGER: Red. Indicates an imminently hazardous

situation that, if not avoided, will result in death or

serious injury. This signal word is to be limited to

the most extreme situations typically for machine

components which, for functional purposes, cannot be

guarded.

WARNING: Orange. Indicates a potentially hazardous

situation that, if not avoided, could result in death or

serious injury, and includes hazards that are exposed

when guards are removed. It may also be used to

alert against unsafe practices.

CAUTION: Yellow. Indicates a potentially hazardous

situation that, if not avoided, may result in minor or

moderate injury. It may also be used to alert against

unsafe practices.

IMPORTANT: Blue. Indicates procedures which

should be

followed to avoid damage to the machine.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY DECAL LOCATION

REMEMBER: If Safety Signs have been damaged, removed, become illegible or parts replaced

without decals, new decals must be applied. New decals are available from your authorized

distributor or factory.

A 45-213 Decal, Dashboard Warning - DIESEL

45-095 Decal, Dashboard Warning - GASOLINE

B 30-117 Decal, Low Sulfur Fuel

C 25-286 Decal, Warning Pinch Points

D 25-277 Decal, Warning Battery

E 25-298 Decal, Warning Hot

F 16-088 Decal, Warning Moving Parts/Hot - DIESEL (Belt Guard)

G 25-337 Decal, Speed Boss - Hang Tag

H 25-352 Decal, Bypass Valve - Hang Tag on pump

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine (engine,

accessories and attachments).

2. Never allow anyone to operate or service the machine or its attachments without proper training and

instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all Personal Protective Equipment (PPE) on your head, eyes, ears, hands and feet. Operate the

machine only in daylight or in good articial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can nd before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without

proper ventilation.

9. Fuel is highly ammable, handle with care. When lling tank stop 1 inch(2.54 cm) from top. Leave room

for expansion. DO NOT OVERFILL.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. After engine has started machine must not move. If movement is evident, the neutral mechanism is not

adjusted correctly. Shut engine off and readjust so the machine does not move when in neutral position.

13. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and

cause serious injury.

14. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not stop or start suddenly on any slope.

C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.

D. Stay alert for holes in the terrain and other hidden hazards.

15. Before leaving operator’s position for any reason:

A. Disengage all drives.

B. Lower all attachments to the ground.

C. Set park brake.

D. Shut engine off and remove the ignition key.

16. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

17. Keep the area of operation clear of all bystanders.

18. Never carry passengers.

19. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

20. Use parts and materials supplied by Smithco only. Do not modify any function or part.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

GAS SAND STAR SPECIFICATIONS

WEIGHTS AND DIMENSIONS

Length 68" (1.73 m)

Width 58" (1.47 m)

Height 52" (1.2 m)

Wheel Base 42" (1.07m)

Ground Clearance 5.5" - 7" (13 -18 cm) - under cultivator depending on attachment

Weight 2WD - 875 lbs. (397 kg) 3WD - 915 lbs. ( 415 kg)

SOUND LEVEL (EAR PROTECTION REQUIRED)

At Ear Level 87 dB

ENGINE 2WD (45-001) 3WD (45-002 & 45-003 & 45-204)

Make Briggs and Stratton Vanguard Briggs and Stratton Vanguard

Model# 305447 356447

Type / Spec# 0230 G1 0263 G

Horsepower 16 hp (11.9 kW) 18 hp (13 kW)

Fuel Unleaded 87 Octane Gasoline Minimum

Lubrication System Full Pressure

Alternator 16 amp

WHEELS & TIRE Three: 22 X 11 - 10.0 Knobby Tires 5 psi (.34 bar)

Optional: 23-10.50 x 12 Turf Tires 5 psi (.34 bar)

SPEED

Forward Speed 0 to 10 m.p.h. (0-16 kph)

Reverse Speed 0 to 5 m.p.h. (0-8 kph)

BATTERY Automotive Type SP 35

BCI Group Size 35

Cold Cranking Amps 300

Ground Terminal Polarity Negative (-)

Maximum Length 7.5" (19 cm)

Maximum Width 5" (12,7 cm)

Maximum Height 7.5" (19 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 20 quarts (18.93 liters)

Hydraulic Fluid 20 quarts (18.93 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

DIESEL SAND STAR SPECIFICATIONS

WEIGHTS AND DIMENSIONS

Length 68" (1.7 m)

Width 58" (1.47 m)

Height 52" (1.2 m)

Wheel Base 42" (1.07 m)

Weight 1020 lbs. ( 508 kg)

SOUND LEVEL (EAR PROTECTION REQUIRED)

At Ear Level 89 dB

ENGINE

Make Kubota

Model# D-722

Type / Spec# E3B

Horsepower 18 hp (14 kW)

Fuel Diesel fuel No. 2

No. 2-D, S500: Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%

No.2-D, S15: Ultra Low Sulfur Diesel (ULSD) less than 15 ppm or 0.0015

wt.%

Cooling System Liquid Cooled

Lubrication System Full Pressure

Alternator 16 amp

WHEELS & TIRE Three: 22 X 11 - 10.0 Knobby Tires 5 psi (.34 bar)

Optional: 23-10.50 x 12 Turf Tires 5 psi (.34 bar) Smithco # 48-265

Front tire uid lled to 80 lbs. Total 45.5 pints of windshield washer uid

SPEED

Forward Speed 0 to 11 m.p.h. (0-18 kph)

Reverse Speed 0 to 5 m.p.h. (0-8 kph)

BATTERY Automotive Type SP-35

BCI Group Size 35

Cold Cranking Amps 300

Ground Terminal Polarity Negative (-)

Maximum Length 9" (23 cm)

Maximum Width 5.38" (14 cm)

Maximum Height 9" (23 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 20 quarts (18.93 liters)

Hydraulic Fluid 20 quarts (18.93 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

ROPS CERTIFICATION

ROPs ISO 21299

Seat belts OSHA 1928.51

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP

The Bunker Rakes arrive from Smithco with some assembly required before service.

1. Set park brake. Push the brake down past center and the park brake is engaged.

2. Rear wheel mounting. Block front tire. Jack up rear of machine

being careful not to damage underside of machine. Place wheel

on hub lining up bolt holes. Use the ten lug nuts provided. Then

torque to 64 - 74 ft/lb (87-100 Nm) using a cross pattern. Re-

torque after the rst 10 hours and every 200 hours thereafter.

Lower machine to ground and remove blocks and jack.

3. Install steering wheel (Ref 1) on machine. Put steering wheel onto

shaft (Ref 3) or tilt steering mechanism. Line up holes and insert

x 2" Roll Pin (Ref 2) into wheel shaft or tighten nut, depending

the model.

4. Check the tire pressure. The Knobby tire pressure should be 5 psi

(0.34 bar). Turf Trac Tire pressure should be 5 psi (.34 bar).

5. Battery not furnished. Install an automotive type 45 -12 volt;

480 cold cranking amps (minimum) battery in the battery box of

the Sand Stars This is a negative grounding system. Attach the battery hold-downs. Then attach red

positive (+) cable (A) to positive terminal. Slide rubber

boot over the positive terminal to prevent shorts.

Attach black negative (-) cable (B) to the negative

terminal.

Connecting battery cables to

the wrong post could result in

personal injury and/or damage

to the electrical system. Make

sure battery and cables do not interfere or rub

on any moving part. Connect the red positive

(+) cable (A) to the battery rst. When discon-

necting remove the black negative (-) cable

(B) rst.

6. Check engine oil and add as necessary. See engine manual for recommended motor oil. DO NOT

OVERFILL.

7. Fill Gas Tanks with Unleaded 87 Octane gasoline (minimum). Fill Diesel Fuel Tank with No. 2-D, S500:

Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%. When lling the fuel tank stop when the fuel

reaches 1 inch (2.54cm) from the top. This space is necessary for fuel expansion. DO NOT OVERFILL.

Fuel is ammable. Caution must be used when storing or handling it. Do

not ll fuel tank while engine is operating or in an enclosed area. Fumes are

explosive and dangerous to inhale. DO NOT SMOKE while lling the fuel tank.

DO NOT OVERFILL.

8. Check hydraulic oil level on the tank. The level should be

2 -2

"(5 - 6.35 cm) from top of tank. If level

is low, add SAE 10W-40 API Service SJ or higher motor oil.

9. Machine should be greased before starting.

10. Read operating instructions before starting machine.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS GAS MODELS

INSTRUMENTS LOCATED ON THE CONTROL PANEL

A. Oil Light - The oil light should come on when ignition is

on without engine operating. The oil light will light when

the oil pressure is low. If oil light should come on, shut

off engine immediately and nd the cause.

B . Ignition Switch - The ignition switch has three posi-

tions: Off-Run-Start.

C . Hand Throttle - The hand throttle is used to regulate

engine speed.

D. Choke - Pull choke control knob up to close choke plate

when starting a cold engine. A warm engine may not

require "choking" to start.

E. Hour Meter - The hour meter indicates hours of ma-

chine operation. It operates only when the ignition

switch is on.

F. Light - (OPTIONAL) This is a Rocker switch to turn on

and off lights.

G. On/Off valve - Sand Star II and Sand Star III ONLY.

Rocker Switch to turn on/off 3 wheel drive.

STEERING

Acquaint yourself with the steering before operating the machine. This ma-

chine is equipped with a tilt steering mechanism. The lever to tilt the steering

wheel is located at bottom of rubber boot on steering column. Hold the lever

down and adjust the steering wheel to a comfortable position.

RAKE LIFT LEVER

Located on right fender, this lever (H) raises and lowers all rear attachments.

To raise push forward, to lower pull back. Release the lever when attachment

is in proper position and lever will return to neutral.

LIFT ASSEMBLY LEVER

Located on right fender, this lever (J) raises and lowers all attachments under

the center of the machine. To raise push forward, to lower pull back. Release

the lever when attachment is in proper position and lever will return to neutral.

FRONT HYDRAULIC PLOW (OPTIONAL COMES WITH PLOW)

Located on right fender, this lever (K) raises and lowers the hydraulic plow in

front of machine. To lower push forward, to raise pull back. Release the lever

when attachment is in proper position and lever will return to neutral.

RIGHT FLOORBOARD

Foot Pedal controls forward and reverse motion. Pushing down on the inside

pedal (L) will give you a forward motion and pushing down on outside pedal

(M) will give you a reverse motion. When pedal is released the hydrostatic

transmission centers and stops the vehicle. Ground speed is proportional to

how far the foot pedal is depressed.

SEAT ADJUSTMENT

Seat adjustment lever is located under front of seat on left side. It allows seat

adjustment forward or backward for operator's comfort. The seat also has the

start safety switch in it. To start the Sand Star the operator must be sitting on

the seat.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS DIESEL MODEL

INSTRUMENTS LOCATED ON THE CONTROL PANEL

A. Hour Meter - The hour meter indicates hours

of machine operation. It operates only when the

ignition switch is on.

B . Glow Plug: When ignition is turned to preheat,

glow plug lights when ready to start.

C . Temperature Light: The temperature light will

come on if machine starts to over heat.

D. Oil Light - The oil light should come on when

ignition is on without engine operating. The oil

light will light when the oil pressure is low. If oil

light should come on, shut off engine immedi-

ately and nd the cause.

E. Ignition Switch - The ignition switch has three

positions: Off-Run-Start.

F. Hand Throttle - The hand throttle is used to

regulate engine speed.

G. Light - (OPTIONAL) This is a Rocker switch to

turn on and off lights

STEERING

Acquaint yourself with the steering before operating the machine. This ma-

chine is equipped with a tilt steering mechanism. The lever to tilt the steer-

ing wheel is located at bottom of rubber boot on steering column. Hold the

lever down and adjust the steering wheel to a comfortable position.

RAKE LIFT LEVER

Located on right fender, this outside lever (H) raises and lowers all rear

attachments. To raise push forward, to lower pull back. Release the lever

when attachment is in proper position and lever will return to neutral.

LIFT ASSEMBLY LEVER

Located on right fender, this inside lever (J) raises and lowers all attach-

ments under the center of the machine. To raise push forward, to lower pull

back. Release the lever when attachment is in proper position and lever

will return to neutral.

FRONT HYDRAULIC PLOW (OPTIONAL COMES WITH PLOW)

Located on right fender, this lever raises and lowers the hydraulic plow in

front of machine. To lower push forward, to raise pull back. Release the lever

when attachment is in proper position and lever will return to neutral.

RIGHT FLOORBOARD

Foot Pedal controls forward and reverse motion. Pushing down on the inside

pedal (L) will give you a forward motion and pushing down on outside pedal

(M) will give you a reverse motion. When pedal is released the hydrostatic

transmission centers and stops the vehicle. Ground speed is proportional to

how far the foot pedal is depressed.

SEAT ADJUSTMENT

Seat adjustment lever is located under front of seat on left side. It allows seat adjustment forward or backward

for operator's comfort. The seat also has the start safety switch in it. To start the Sand Star the operator must

be sitting on the seat.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS AND INSTRUMENTS

PARK BRAKE

The park brake is located on the left hand side of the

machine and operates both rear wheels. Pull lever back

to engage and push forward to disengage.

To adjust, turn the knob on the end of the handle.

OPERATION

STARTING ENGINE

Before operating this machine, become familiar with all controls and functions

of these units. Also complete all maintenance requirements and read all safety

warnings. By knowing the machine thoroughly, how it operates and by doing the

prescribed maintenance steps, you can expect relatively trouble-free operation for

years to come.

1. Make sure the fuel ow valve, located on the fuel tank, is “ON.”

2. Set park brake. Start safety switch is on the park brake.

3. The ignition switch is a three position on gas and four position on diesel. For

Gas engines: Insert key (A) and turn clockwise until engine starts (C). Re-

lease key and it will return to run position (B). Use choke and hand throttle

as necessary. For Diesel Engines: Insert key (A) and turn clockwise to (B).

When glow light goes out, turn key clockwise until engine starts (C). Release

key and it will return to run position (B).

4. Allow engine to idle and warm up a few minutes before selecting a direction

of travel.

5. To shut off engine on all gas machines turn key to the stop position.

COLD WEATHER STARTING

When attempting to start the engine in cold weather, the oil in the hydrostatic pump

may provide too much resistance to start a cold machine.

Before attempting to start the engine in cold weather, disengage the drive belt to

the hydrostatic by pushing down the idler lever until it catches in the notch on the

latching lever. Start engine and allow it to warm up with no load. When the engine is

warm, shut off engine. Push down on the latching lever until the idler is released.

Engine must be stopped when the drive belt is engaged. If the engine is running when the belt is engaged,

the vehicle may move suddenly, injuring you and/or bystanders.

Always stop the engine before reengaging the drive belt. The sudden application of power to the hydrostatic

may cause serious damage the pump, the engine or both.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

Use all procedures and parts prescribed by the manufacturer's. Read the en-

gine manual before operation.

ENGINE

For Briggs and Stratton

Change and add oil according to chart below. Do not overll. Engine oil capacity is 2 quarts. We recommend

high-quality detergent oils classied for service SF, SG, SH, SJ or higher. Do not use special additives. Out-

door temperatures determine the proper oil viscosity for the engine. Use the chart to select the best viscosity

for the outdoor temperature range expected.

SAE VISCOSITY GRADES

Starting Temperature Range Anticipated Before Next Oil Change

ENGINE

For Kubota Diesel engine

Use oil classied “For Service CC, CD or CE” API oil. Use no special additives with recommended oils. Do not

mix oil with gasoline. If the CF-4 or CG-4 lubrication oil is used with high-sulfur fuel, change the lubricating oil

more often.

Starting Temperature Range Anticipated Before Next Oil Change

SAE VISCOSITY GRADES

Use of multi-viscosity oils (10W-30, etc.) above 80° F (27° C) will result in high oil consumption and possible

engine damage. Check oil level more frequently if using these types of oils.

SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to

inadequate lubrication.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

DAILY CHECK LIST

The suggested maintenance checklist is not offered as a replacement for the manufacturer’s but as a supple-

ment. You must adhere to guidelines established by manufacturer for warranty coverage. In adverse condi-

tions such as dirt, mud or extreme temperatures, maintenance should be more frequent.

DAILY CHECKLIST

1. Check park brake adjustment. Adjust as required.

2. Check engine oil level. Add as needed. DO NOT OVERFILL.

3. Tire pressure should be 5 psi (0.34 bar) maximum .

4. Inspect electrical system for loose connections or frayed wiring, including battery cables. Replace any

faulty equipment or tighten if loose.

5. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.

6. Inspect hydraulic lines for damage or leaks. Never use hands to inspect leaks.

7. Check hydraulic oil level on the tank. The level should be

2 -2

"(5 - 6.35 cm) from top of tank. If level

is low, add SAE 10W-40 API Service SJ or higher motor oil.

8. Inspect steering, throttle and shift linkages for good hookups and clear travel.

9. Check anti-vibration mounts on engine frame.

10. Check controls for smooth, proper working operation. Lubricate as needed.

11. Remove debris from engine compartment

12. Check cyclonic air cleaner.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SERVICE CHART DIESEL

Before servicing or making adjustments to the machine, stop engine, set park break,

block wheels and remove key from ignition.

Follow all procedures and ONLY use parts prescribed by the manufacturer. Read the

engine manual before maintenance.

The suggested maintenance checklist is not offered as a replacement for the manufacturer’s engine manual but as a sup-

plement. You must adhere to the guidelines established by the manufacturer for warranty coverage. In adverse conditions

such as dirt, mud or extreme temperatures, maintenance should be more frequent.

Maintenance Service Interval Maintenance Procedure

Aer the rst 8 operating hours Torque the wheel lug nuts. (64-74 /lb (87-100 Nm))

Change the engine oil lter.

Before each use daily Check the engine oil level.

Clean area around muer and controls.

Check the hydraulic uid level.

Check the tire pressure.

Check condition of hydraulic hoses and ttings.

Check for oil or water leaks.

Proper function of glow lamp timer.

Color of exhaust fumes.

Inspect and clean the machine.

Aer the rst 50 hours Change Hydraulic Oil Filter.

Change Engine oil and lter.

Every 100 hours Clean or change air lter.1

Clean pre-cleaner.1

Change engine oil and lter.

Lubricate machine.

Clean or change remote air cleaner.

Check the battery uid level and cable connections..

Check belt tension .

Every 200 hours Check radiator hoses and clamp bands.

Check idle speed.

Replace oil lter cartridge.

Change hydraulic oil lter.

Check air intake line

Torque the wheel lug nuts. (64-74 /lb (87-100 Nm))

Every 500 hours or yearly Change fuel lter.

Change hydraulic oil and lter.

Clean oil cooler ns.1

Clean air cooling system.1

Change radiator coolant.

Check safety lter in remote air cleaner.

1 In dusty conditions or when airborne debris is present, clean more oen.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SERVICE CHART GASOLINE

Before servicing or making adjustments to the machine, stop engine, set park

break, block wheels and remove key from ignition.

Follow all procedures and ONLY use parts prescribed by the manufacturer.

Read the engine manual before maintenance.

The suggested maintenance checklist is not offered as a replacement for the

manufacturer’s engine manual but as a supplement. You must adhere to the guidelines established by the

manufacturer for warranty coverage. In adverse conditions such as dirt, mud or extreme temperatures, main-

tenance should be more frequent.

Maintenance Service Interval Maintenance Procedure

Aer the rst 8 operating hours Torque the wheel lug nuts. (64-74 /lb (87-100 Nm))

Change the engine oil lter.

Before each use daily Check the engine oil level.

Clean area around muer and controls.

Check the hydraulic uid level.

Check the tire pressure.

Check condition of hydraulic hoses and ttings.

Inspect and clean the machine.

Aer the rst 50 hours Change Hydraulic Oil Filter.

Every 100 hours Clean or change air lter.1

Clean pre-cleaner.1

Change engine oil and lter.

Replace spark plug .

Lubricate machine.

Clean or change remote air cleaner.

Check the battery uid level and cable connections..

Check muer and spark arrestor.

Check belt tension .

Every 250 hours Check engine valve clearance and adjust if necessary.

Check idle speed.

Clean battery terminals.

Change hydraulic oil lter.

Torque the wheel lug nuts. (64-74 /lb (87-100 Nm))

Every 500 hours or yearly Change fuel lter.

Change hydraulic oil and lter.

Clean oil cooler ns.1

Clean air cooling system.1

Check safety lter in remote air cleaner.

1 In dusty conditions or when airborne debris is present, clean more oen.

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

END USER’S SERVICE CHART

Duplicate this page for routine use.

Maintenance Check Item For the week of:

Mon Tues. Wed. urs. Fri. Sat. Sun.

Check the Safety Seat Switch

Check Steering Operation

Check the fuel level

Check the engine oil level.

Clean the air lter

Clean the engine cooling ns.

Check for unusual engine noises

Check the hydraulic oil level

Check hydraulic hoses and ttings for

damage

Check for uid leaks.

Check the tire pressure

Check the Instrumentation

Inspect electrical system for frayed wires

Check park brake adjustment

Change oil lter.

Change oil.

Lubricate Machine

Ensure all warning decals are intact.

Areas of Concern

Inspection Performed by:

Item Date Information

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

HOW TO RAKE A SAND TRAP

View bunker to determine the most efcient pattern to follow so that rake pattern and conguration of bunker will ow in

same general direction and look attractive.

Enter bunker at its lowest point. Perhaps drain area or another point where “lip” of the trap is minimal.

Operate at 2-4 m.p.h. (3-6.5 kph) for best raking results. Control speed with hydraulic pedal.

Once fully inside bunker, lower rear rake and proceed forward as described above.

First pass should be directly down center of

trap. This helps avoid extremely sharp turns

that will spoil sands’ appearance. Once at far

end, turn machine and drive down one side of

trap and come back up other side.

Grass or other material may build up on rake

tines as machine passes “enter/exit” point in

Figure 1. Lift rake briey while still moving

forward.

Do not rake closer than 6" (15 cm) to edge of trap.

Do not rake slopes in trap. The weight of machine will pull sand down.

Use cultivator or other center mounted accessories only as necessary for compacted sand. Frequent use will leave sand

too soft and objectionable to some golfers.

Use front mounted plow to push sand to desired locations within trap.

After exiting trap, secure machines in accordance with practices described in this manual. Rake trap edges, slopes and

“enter /exit” area with a hand rake.

After returning to maintenance area, thoroughly clean machine, check uids, and lubricate as advised in this manual.

QUICK HITCH

Bunker Rakes are tted with a Quick Hitch Accessory Mount System. On each mount is a spring loaded locking

mechanism and a lock pin. Remove the lock pin and push down on the spring loaded locking mechanism and your

rear attachment will pull off, so you can easily switch out attachments. The lock pin acts as a safety device to keep

lock pin from opening up when crossing rough terrain.

There are also adjustment screws on the Quick Hitch Accessory Mount System that may need to be adjusted for

certain rear attachments. These allow the rear attachment to move from side to side without touching the rear

wheels. Please see instructions on each individual attachment that you purchase.

Run machine and test for operation of the rear attachment by raising and lowering the assembly and with the

attachment down turn sharp corners in both directions to

ensure rake is not contacting the tires.

Adjustment Screws

Spring Loaded

Locking Mechanism

Service

PARTS MANUALS AVAILABLE ONLINE AT smithco.com



BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or any ignited

object to come near the battery. When charging or working near battery, always shield your eyes and always provide

proper ventilation.

Battery cable should be disconnected before using "Fast Charge".

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging rate. If

electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp rst and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte is splashed on

any part of your body, ush all contact areas immediately with liberal amounts of water. Get medical

attention immediately.

JUMP STARTING

Use of booster battery and jumper cables. Particular care should be used when connecting a booster

battery. Use proper polarity in order to prevent sparks.

To jump start (negative grounded battery):

1. Shield eyes.

2. Connect ends of one cable to positive (+) terminals of bottom

post on solenoid rst (A), then positive post of booster battery.

(B).

3. Connect one end of other cable to negative (-) terminal of

booster battery (C).

4. Connect other end of cable (D) to engine block on unit being

started.

To prevent damage to other electrical components on unit being

started, make certain that engine is at idle speed before disconnect-

ing jumper cables.

Pagina se încarcă...

Smithco Sand Star Instrucțiuni de utilizare

Marca: Smithco

Model: Sand Star

Categorie: Accesorii pentru autovehicule

Tip: Instrucțiuni de utilizare

Descărcați PDF

raport

în alte limbi

English: Smithco Sand Star Operating instructions
eesti: Smithco Sand Star Kasutusjuhend

Smithco Sand Star Instrucțiuni de utilizare

Smithco Sand Star Instrucțiuni de utilizare

în alte limbi

Lucrări înrudite

Alte documente