Parkside PKLL 7 C3 Manual de utilizare

C

ROSS LINE LASER PKLL 7 C3

KREUZLINIENLASER

Originalbetriebsanleitung

CROSS LINE LASER

Translation of the original instructions

LASER ZA KRIŽNE LINIJE

Prijevod originalnih uputa

LASER CU LINII ÎN CRUCE

Traducerea instrucţiunilor de utilizare originale

LASER SA UKRŠTENIM

LINIJAMA

Prevod originalnog uputstva za upotrebu

IAN 312017

ЛАЗЕР С КРЪСТОСАНИ

ЛИНИИ

Превод на оригиналната инструкция

ΑΛΦΑΔΙ LASER ΣΤΑΥΡΟΥ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

C

ROSS LINE LASER PKLL 7 C3

GB / CY Translation of the original

instructions Page 5

HR Prijevod originalnih uputa Stranica 22

RS Prevod originalnog uputstva za

upotrebu Strana 39

RO Traducerea instrucţiunilor de

utilizare originale Pagina 60

BG Превод на оригиналната

инструкция Cтраница 77

GR / CY Μετάφραση των αυθεντικών

οδηγιών λειτουργίας Σελίδα 102

DE / AT / CH Originalbetriebsanleitung Seite 122

2

1

3

45

6

7

8

9

10

1

2

A

3a

A1

A2

5

5 GB/CY

List of pictograms used ..................................... Page 6

Introduction ................................................................ Page 7

Intended use ..................................................................... Page 7

Description of parts .......................................................... Page 8

Scope of delivery ............................................................. Page 8

Technical data .................................................................. Page 8

Safety notes ............................................................... Page 9

Safety instructions for batteries / rechargeable batteries .... Page 12

Initial use ...................................................................... Page 14

Inserting / Changing batteries ......................................... Page 14

Switching on / off ............................................................. Page 14

Use automatic levelling system........................................ Page 15

Working without the automatic levelling system ............ Page 16

Practical guidance ........................................................... Page 16

Working with the clamp .................................................. Page 16

Working with the tripod ................................................... Page 17

Maintenance and cleaning ............................ Page 17

Storage .......................................................................... Page 18

Disposal ......................................................................... Page 18

Warranty ...................................................................... Page 19

Warranty claim procedure .............................................. Page 20

Service .............................................................................. Page 21

6 GB/CY

List of pictograms used

Please read the instructions for use.

Danger of explosion!

Wear safety gloves!

Attention! - The manual must be consulted in all

cases where this symbol is marked.

Protect yourself from laser radiation!

Do not stare into the laser beam!

Volt (Direct Current)

Alkaline batteries included

7 GB/CY

Cross Line Laser PKLL 7 C3

Introduction

We congratulate you on the purchase of your new

product. You have chosen a high quality product. The

instructions for use are part of the product. They contain

important information concerning safety, use and disposal. Before

using the product, please familiarise yourself with all of the safety

information and instructions for use. Only use the product as de-

scribed and for the speciﬁed applications. If you pass the product

on to anyone else, please ensure that you also pass on all the

documentation with it.

Intended use

The product is suitable for the the determination and veriﬁcation of

horizontal and vertical lines. The product is exclusively suitable for

use in enclosed operating sites. Any other use or modiﬁcation of the

product shall be considered improper use and may result in serious

accidents. The manufacturer assumes no liability for damages due

to improper use. Not intended for commercial purposes.

8 GB/CY

Description of parts

1

Ring-button

2

LED indicator (red: levelling oﬀ, green levelling on)

3

Battery compartment

3a

Battery compartment cover

4

LOCK Switch

5

-thread (underneath)

6

Laser beam opening

7

-screw (to align with -thread of cross line laser)

8

Retaining screw

9

Clamp Jaw

10

Clamping Nut

Scope of delivery

1 Cross line laser

1 Clamp

2 1.5 V-Batteries, Type AAA

1 Set of instructions for use

Technical data

Operating voltage: 3 V (direct current)

Working area

1)

: 7 m

Levelling accuracy: +/- 0.8 mm / m

Typical self-levelling range: ± 4°

9 GB/CY

Typical levelling time: approx. 6 seconds

Operating temperature: +5 °C–35 °C

Max. relative humidity: ≤ 90 %

Laser class: 2

Wave length (λ): 635 nm

Maximum performance P max: 1 mW

Clamp mount:

Batteries: 2 x 1.5 V-Batteries, Type AAA

Product weight: 240 g (with batteries)

Clamp weight: 160 g

Product dimensions: approx. 67 x 66 x 84 mm

Max. Clamp jaw opening: 60 mm

Degree of protection: IP20

Max. operation altitude: 2000 m

1) The operating range can be reduced by unfavourable environ-

mental conditions (e.g. direct sunlight).

Safety notes

DANGER OF SUFFOCATION! Packaging materials (e.g.

ﬁlms or polystyrene) can not be used as toys. Always keep

children away from the packaging material. The packaging

material is not a toy.

Do not work with the measuring tool in an environment where

there is a danger of explosion, where there are ﬂammable liq-

uids, gasses or dusts. Sparks can be created in the product,

which could ignite dust or fumes.

10 GB/CY

Test on known sources before use, to make sure that equipment

is functioning correctly.

If the equipment is used in a manner not speciﬁed by the man-

ufacturer, the protection provided by the equipment may be

impaired.

The manual must be consulted in all cases where symbol

is marked.

This product may be used by children from the age of 8, by

persons of reduced physical, sensory or mental abilities or a

lack of experience and / or knowledge if they are supervised or

instructed with regard to the safe use of the product and have

understood the risks resulting from use. Do not allow children

to play with the product. Cleaning and user maintenance may

not be carried out by children unless they are supervised.

Do not leave the switched-on product unattended and switch

the product oﬀ after use. Others could be blinded by the laser

beam. Risk of eye injury.

Do not expose the product to moisture or direct sunlight.

Do not expose the product to extremely high temperatures or

temperature ﬂuctuations. For example, do not leave it in your

car for a long time. In the case of large temperature ﬂuctuations,

let the product acclimatise before using it. In extreme tempera-

tures or temperature ﬂuctuations, the precision of the product

can be impaired.

Avoid strong impacts against the measuring tool. Damage to

the measuring tool can impair its accuracy. After a strong impact

compare the laser line with a known vertical or horizontal ref-

erence line to check it.

11 GB/CY

Turn the measuring tool oﬀ when you transport it. When it is

switched oﬀ the pendulum unit is locked, which otherwise can

be damaged in strong movements.

Do not bring the measuring tool near to heart pacemakers.

The magnet inside the measuring tool creates a ﬁeld that can

impair the function of pacemakers.

Keep the measuring tool away from magnetic data carriers and

devices that are sensitive to magnetic inﬂuences. The eﬀects of

the magnet can lead to irreversible data losses.

Protect yourself from laser

radiation!

LASER

2

P

max

< 1 mW

λ = 635 nm

EN 60825-1:2014

Do not look directly into the laser beam or the laser beam

opening

6

.

Viewing the laser beam with optical instruments

(e.g. loupe, magnifying glass etc.) is associated with risk injury

to the eyes.

CAUTION! If operating or adjusting devices than other than

those described here are used or other procedures are carried

out, this can lead to dangerous radiation eﬀects.

12 GB/CY

Never direct the laser beam at people, animals or reﬂective

surfaces. Even looking brieﬂy into the laser beam can cause

damage to the eyes.

The laser assembly inside the equipment can be examined,

repaired or replaced by the manufacturer only. If functional or

other defects occur, please contact the service department

listed either by telephone or by e-mail.

The radiation pattern emitted from this equipment during the

performance of operation and maintenance procedure:

• Wavelength: 635 nm

• Maximum power or energy output: <1mW

Safety instructions for batteries /

rechargeable batteries

DANGER TO LIFE! Keep batteries / rechargeable batteries

out of reach of children. If accidentally swallowed seek imme-

diate medical attention.

DANGER OF EXPLOSION! Never recharge

non-rechargeable batteries. Do not short-circuit bat-

teries / rechargeable batteries and / or open them.

Overheating, ﬁre or bursting can be the result.

Never throw batteries / rechargeable batteries into ﬁre or water.

Do not exert mechanical loads to batteries / rechargeable

batteries.

13 GB/CY

Risk of leakage of batteries / rechargeable batteries

Avoid extreme environmental conditions and temperatures,

which could aﬀect batteries / rechargeable batteries, e.g.

radiators / direct sunlight.

If batteries / rechargeable batteries have leaked, avoid contact

with skin, eyes and mucous membranes with the chemicals!

Flush immediately the aﬀected areas with fresh water and

seek medical attention!

WEAR PROTECTIVE GLOVES! Leaked or dam-

aged batteries / rechargeable batteries can cause

burns on contact with the skin. Wear suitable pro-

tective gloves at all times if such an event occurs.

In the event of a leakage of batteries / rechargeable batteries,

immediately remove them from the product to prevent damage.

Only use the same type of batteries / rechargeable batteries.

Do not mix used and new batteries / rechargeable batteries.

Remove batteries / rechargeable batteries if the product will

not be used for a longer period.

Risk of damage of the product

Only use the speciﬁed type of battery / rechargeable battery!

Insert batteries / rechargeable batteries according to polarity

marks (+) and (-) on the battery / rechargeable battery and

the product.

Clean the contacts on the battery / rechargeable battery and

in the battery compartment before inserting!

Remove exhausted batteries / rechargeable batteries from the

product immediately.

14 GB/CY

Initial use

Check that the delivery is complete and that there is no visible

damage.

Remove the packaging material from the product.

Inserting / Changing batteries

Open the battery compartment cover

3a

as shown in the

ﬁg A1.

Insert batteries into the battery compartment

3

as shown in

the ﬁg A2.

Make sure that the batteries are inserted in a correct polarity

as shown in the ﬁg A2 before closing back the battery com-

partment cover

3a

.

Note: when the battery is low, the LED indicator

2

blinks red.

Always replace all batteries at the same time. Only use batteries

from the same manufacturer and with the same capacity.

Remove the batteries from the product if it will not be in use

for a prolonged period of time. In long periods of storage the

batteries can corrode and can run themselves down.

Switching on/oﬀ

To switch the product on, push the LOCK switch

4

to the

position

. Immediately after being switched on, the product

releases two laser lines from the laser beam opening

6

.

15 GB/CY

To switch the product oﬀ, push the LOCK switch

4

to the

position

. When switched oﬀ, the pendulum unit is locked.

Use automatic levelling system

To work with automatic levelling, place the product on a level,

ﬁrm surface, or fasten it with the

-thread

5

to -screw

7

of supplied clamp.

When it is switched on, the automatic levelling system auto-

matically corrects irregularities of ±4° within the self levelling

area. The levelling is concluded when the laser lines stop

moving and the LED indicator

2

goes green.

If automatic levelling is not possible, e.g. because the base of

the measuring tool deviates by more than 4° from the horizon-

tal or because the product is being freely hand-held, the LED

indicator

2

will go red and the horizontal and vertical laser

lines will be switched oﬀ.

Note 1: operation without automatic levelling will always be

indicated via the red LED indicator

2

.

Note 2: if the product is agitated or its position is changed

during operation, the product will automatically re-level. After

re-levelling check the positions of the horizontal and vertical

laser lines against reference points to avoid errors.

Note 3: The top Ring-button

1

has no function at this mode.

16 GB/CY

Working without the automatic

levelling system

Put the LOCK switch

4

into the position .

Push the ring-button

1

on the top of the product. Now the

product will release two laser lines from the laser beam open-

ing

6

that are not levelled. Operation without automatic lev-

elling will always be indicated via the red LED indicator

2

.

Push the ring-button

1

on top again to turn oﬀ the product at

this mode.

Practical guidance

Always use only the middle of the laser line for markings. The

width of the line depends on the distance.

Working with the clamp

The clamp provided can be used to attach the device to various

objects.

1. Release the clamping nut

10

by rotating the clamping nut anti-

clockwise.

2. Position the clamping jaws

9

to the desired location.

3. Rotate the clamping nut

10

clockwise until fastened.

4. Place

-thread

5

of cross line laser with the -screw

7

of

the clamp and tighten with hand. Do not use excessive force

as this may damage the device.

17 GB/CY

5. Align the cross line laser. To do so, release the retaining screw

8

by rotating anti-clockwise and move the cross line laser

into the desired position.

6. Fix the position by fastening the retaining screw

8

.

Working with the tripod

You can place the cross line laser in a stable position and adjust

the height using a tripod (not provided in scope of delivery).

Place the cross line laser with

-thread

5

onto the -screw of

your tripod and tighten by hand. Do not use excessive force as this

may damage the device.

Maintenance and cleaning

The product requires no maintenance.

ATTENTION! Never submerge the product in water or other

liquids. Do not allow water to enter into the product during

cleaning.

Keep the product clean to ensure good, secure work.

Use a dry cloth to clean the outside.

Clean the laser beam opening

6

with a soft air jet. In cases

of heavy contamination, remove the dirt with a slightly damp

Q-tip. Do not exert any strong pressure!

For repair purposes the product may only be

opened by a professional.

18 GB/CY

Have the measuring tool repaired by qualiﬁed professionals

and only with original replacement parts. This ensures that the

safety of the measuring tool is maintained.

Storage

If you will not be using the product for a prolonged period of

time, remove the batteries and store it in a clean, dry place

that is not exposed to direct sunlight.

Disposal

The packaging is made entirely of recyclable materials, which you

may dispose of at local recycling facilities.

b

a

Observe the marking of the packaging materials for

waste separation, which are marked with abbreviations

(a) and numbers (b) with following meaning: 1–7: plas-

tics / 20–22: paper and ﬁbreboard / 80–98: composite

materials.

The product and packaging materials are recyclable,

dispose of it separately for better waste treatment. The

Triman logo is valid in France only.

Contact your local refuse disposal authority for more

details of how to dispose of your worn-out product.

19 GB/CY

To help protect the environment, please dispose of the

product properly when it has reached the end of its use-

ful life and not in the household waste. Information on

collection points and their opening hours can be obtained

from your local authority.

Faulty or used batteries / rechargeable batteries must be recycled

in accordance with Directive 2006/66/EC and its amendments.

Please return the batteries / rechargeable batteries and / or the

product to the available collection points.

Environmental damage through incorrect

disposal of the batteries / rechargeable

batteries!

Batteries / rechargeable batteries may not be disposed of with the

usual domestic waste. They may contain toxic heavy metals and

are subject to hazardous waste treatment rules and regulations.

The chemical symbols for heavy metals are as follows: Cd = cad-

mium, Hg = mercury, Pb = lead. That is why you should dispose of

used batteries / rechargeable batteries at a local collection point.

Warranty

The product has been manufactured to strict quality guidelines and

meticulously examined before delivery. In the event of product

defects you have legal rights against the retailer of this product.

20 GB/CY

Your legal rights are not limited in any way by our warranty de-

tailed below.

The warranty for this product is 3 years from the date of purchase.

Should this product show any fault in materials or manufacture within

3 years from the date of purchase, we will repair or replace it – at

our choice – free of charge to you.

The warranty period begins on the date of purchase. Please keep

the original sales receipt in a safe location. This document is required

as your proof of purchase. This warranty becomes void if the pro-

duct has been damaged, or used or maintained improperly.

The warranty applies to defects in material or manufacture. This

warranty does not cover product parts subject to normal wear, thus

possibly considered consumables (e.g. batteries) or for damage to

fragile parts, e.g. switches, rechargeable batteries or glass parts.

Serbian mark of conformity

Warranty claim procedure

To ensure quick processing of your case, please observe the following

instructions:

Please have the till receipt and the item number (e.g. IAN

123456) available as proof of purchase.

Pagina se încarcă ...

Parkside PKLL 7 C3 Manual de utilizare

Parkside PKLL 7 C3 Manual de utilizare

Lucrări conexe

Alte documente