Parkside PDTS 6.3 B3 Translation Of The Original Instructions

AIR CUT OFF TOOL PDTS 6.3 B3

IAN 327364_1904

AIR CUT OFF TOOL

Translation of the original instructions

ПНЕВМАТИЧЕН ЪГЛОШЛАЙФ

Превод на оригиналното ръководство за експлоатация

POLIZOR PNEUMATIC

Traducerea instrucţiunilor de utilizare original

ΑΕΡΟΤΡΟΧΟΣ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

DRUCKLUFT-TRENNSCHLEIFER

Originalbetriebsanleitung

PNEUMATSKA REZNA BRUSILICA

Prevod originalnog uputstva za upotrebu

GB / CY Translation of the original instructions Page 1

RS Prevod originalnog uputstva za upotrebu Strana 13

RO Traducerea instrucţiunilor de utilizare original Pagina 25

BG Превод на оригиналното ръководство за експлоатация Cтраница 37

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 51

DE / AT / CH Originalbetriebsanleitung Seite 65

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

PDTS 6.3 B3

GB

│

CY

│

1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 3

Technical speciﬁcations ....................................................... 3

General safety instructions .........................................3

Hazards caused by ﬂying parts ................................................. 3

Hazards caused by entanglement ............................................... 4

Hazards during operation ..................................................... 4

Hazards caused by repetitive movements ......................................... 4

Hazards caused by accessories ................................................. 5

Hazards in the workplace ..................................................... 5

Hazards caused by dust and vapours ............................................ 5

Hazards caused by noise ...................................................... 6

Hazards caused by vibrations .................................................. 6

Additional safety instructions for pneumatic machines ................................ 6

Special safety instructions for grinding and abrasive cutting ........................... 7

Additional special safety instructions for abrasive cutting ............................. 7

Kickback and corresponding safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Before use .......................................................8

Changing the cutting disc ...................................................... 8

Setting up .......................................................9

Lubrication ................................................................. 9

Connecting to a compressed airsource ........................................... 9

Switching on and oﬀ ......................................................... 9

Maintenance and cleaning ..........................................9

Disposal ........................................................10

Kompernass Handels GmbH warranty ..............................10

Service .........................................................11

Importer .......................................................11

Original declaration of conformity ..................................12

PDTS 6.3 B3

■ 2

│

GB

│

CY

AIR CUT OFF TOOL

PDTS 6.3 B3

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all of the operating and

safety instructions. Use the product only as described

and for the range of applications speciﬁed. Please

also pass these operating instructions on to any

future owner.

Intended use

The compressed air tool is designed for cutting

thin metal sheets without the use of water. Any

other uses of or modiﬁcations to the appliance are

deemed to be improper usage and may result in

serious physical injury.

Not for commercial use.

Explanation of the symbols used:

WARNING!

Read the operating instructions

before use.

Wear protective goggles!

Direction of rotation

Oil daily!

11/2019 Date of manufacture

11/2021

Expiration date

(visible on the inner metal ring)

Before using the device for the ﬁrst

time, read the original operating

instructions and safety instructions.

Wear ear muﬀs!

Wear safety shoes!

Wear protective gloves!

Wear a dust mask!

Not designed for wet grinding

Using damaged cutting or roughing

discs is dangerous and may cause

serious injury!

Suitable for grinding metal

75

Diameter of the disc

Not approved for side grinding

air cut oﬀ tool

Features

Switch-on guard

Trigger

Blade guard

Tensioning screw

Clamping ﬂange

Cutting disc

Hex key

Spindle

Open-ended spanner

Connector nipple 1/4"

PDTS 6.3 B3

GB

│

CY

│

3 ■

Package contents

1 air cut oﬀ tool

1 cutting disc Ø 75 mm (pre-ﬁtted)

1 open-ended spanner

1 hex key

1 connector nipple (1/4") (pre-ﬁtted)

1 set of operating instructions

Technical speciﬁcations

Rated speed 20300 rpm

Rated air pressure max. 6.3 bar

Disc size Ø 75 x 1 x 10 mm

Spindle dimension M6

Connector nipple 1/4"

Weight: approx. 0.69 kg

Noise emission values:

Noise measurement determined in accordance

with ISO15744:

Sound pressure level L

pA

= 93.6 dB(A)

Uncertainty K

pA

= 3 dB(A)

Sound power level L

WA

= 104.6 dB(A)

Uncertainty K

WA

= 3 dB(A)

Vibration emission value:

Vibration values determined in accordance with

ISO 28927-4 and EN 12096:

a

h

= 3.06 m/s

2

Uncertainty K = 0.53 m/s

2

WARNING!

General safety

instructions

WARNING!

► For multiple hazards: Please ensure that you

have read and understood the safety instruc-

tions before adjusting, operating, repairing,

maintaining or replacement of accessories

on the grinding machine for die grinders

as well as before working in the vicinity of

the machine. Failure to do this can result in

serious bodily injury.

■ The abrasive grinding machine should only be

set up, adjusted or used by suitably qualiﬁed

and trained operators.

■ This machine must not be modiﬁed. Modiﬁ-

cations can reduce the eﬀectiveness of the

safety measures and increase the risks for the

operator.

■ Do not lose the safety instructions – hand

them over to the operator.

■ Never use a damaged abrasive grinding

machine..

■ The machines must be inspected regularly to

ensure that the compressed air abrasive cutter

is marked with the clearly legible ratings and

markings required in this part of ISO 11148.

The employer/user must contact the manufactur-

er to obtain replacement signs if necessary.

Hazards caused by ﬂying parts

■ If a workpiece or accessory or even part of the

machine tool itself breaks, parts can be ﬂung oﬀ

at high speeds.

■ Always wear impact-resistant eye protection

when operating the abrasive grinding machine.

The degree of necessary protection must be

evaluated separately for each individual task.

■ Ensure that the workpiece has been securely

ﬁxed in place.

■ Ensure that the abrasive medium is securely

clamped to the grinding machine.

PDTS 6.3 B3

■ 4

│

GB

│

CY

■ Check that the maximum operating speed of

the abrasive medium, converted into revolutions

per minute, is equal to or higher than the rated

spindle speed.

■ Ensure that the blade guard is mounted, in

good condition, properly fastened and inspected

regularly.

■ Provided that the workpiece encloses the

abrasive medium, a blade guard may not be

required for internal grinding.

■ Check that the clamping ﬂanges are used in

accordance with the manufacturer's instructions

and that they are in good condition, e.g. with-

out cracks and ﬁssures, and are ﬂat.

■ Check whether the spindle and spindle thread

are damaged or worn.

■ Ensure that any sparks and debris produced

during use do not cause any hazards.

■ The grinding machine must be disconnected

from the power supply before changing the

abrasive medium and before maintenance.

Hazards caused by entanglement

■ There may be a risk of suﬀocation, scalping

and/or cuts if loose clothing, jewellery, neck-

laces, hair or gloves are not kept away from

the machine and its accessories.

Hazards during operation

■ Avoid contact with rotating spindle and at-

tached grinding wheel to avoid cuts on the

hands or other body parts.

■ When using the machine, the operator's hands

may be exposed to hazards such as cuts, abra-

sions and heat. Wear suitable gloves to protect

your hands.

■ The operator and maintenance personnel must

be physically capable of handling the size,

mass and power of the machine.

■ Hold the machine correctly:

Be prepared to counteract the usual or sudden

movements. Have both hands ready.

■ Ensure that your body is balanced and that you

have a secure standing position.

■ Release the start/stop control in case of a

disruption to the electricity supply.

■ Use only recommended lubricants.

■ Safety goggles must be worn, protective gloves

and protective clothing are recommended.

■ Wear a safety helmet if working above head

height.

■ After switching oﬀ, do not put the machine

down until the disc comes to a standstill.

■ During abrasive cutting, the workpiece must be

supported in such a way that the cutting slot has

a constant or increasing width during the entire

machining process.

■ If the abrasive medium gets stuck in a cut,

switch oﬀ the abrasive grinding machine and

loosen the grinding wheel. Before continuing

operation, check that the abrasive medium is

still ﬁrmly ﬁtted and not damaged.

■ Grinding wheels and cutting wheels must not

be used for side grinding (exception: grinding

wheels for side grinding). Abrasive grinding

machines may not be used at more than the

maximum speed of the abrasive medium.

■ Make sure that there are no other people

standing in the immediate vicinity.

■ Personal protective equipment such as suitable

gloves, aprons and protective helmets must be

used.

■ Sparks generated by grinding can ignite clothing

and cause severe burns. Ensure that the sparks

do not fall onto clothing. Wear ﬁre-retardant

clothing and make sure there is a bucket of

water nearby.

Hazards caused by repetitive

movements

■ When using a abrasive grinding machine to

perform work-related activities, the operator may

experience unpleasant sensations in the hands,

arms, neck, shoulders or other parts of the body.

■ When using a abrasive grinding machine, the

operator should adopt a comfortable posture

whilst ensuring a secure hold and avoiding

awkward postures or positions in which it is dif-

ﬁcult to maintain balance. The operator should

change positions during the course of long-

lasting tasks. This can be helpful in the preven-

tion of discomfort and fatigue.

PDTS 6.3 B3

GB

│

CY

│

5 ■

■ If the operator notices symptoms such as persis-

tent or recurring illness, discomfort, throbbing,

pain, tingling, burning or stiﬀness, these indica-

tions should not be ignored. The operator must

inform his/her employer and seek the advice

of a suitably qualiﬁed medical practitioner.

Hazards caused by accessories

■ Disconnect the abrasive grinding machine from

the power supply before mounting or replacing

the machine tool or accessory.

■ Use only accessories and consumables of the

sizes and types recommended by the manu-

facturer of the abrasive grinding machine. Do

not use other types or sizes of accessories and

consumables.

■ Make sure that the dimensions of the abrasive

medium are compatible with those of the abra-

sive grinding machine and that the abrasive

medium ﬁts on the spindle.

■ Make sure that the thread type and size of the

abrasive medium exactly matches the thread

type and size of the spindle thread.

■ Inspect the abrasive medium before use.

Do not use abrasive media that may have been

dropped or have chips, cracks or other defects.

■ Ensure that the abrasive medium is properly

ﬁxed and tightened before use; the abrasive

grinding machine must be operated for at least

1 minute in a secure position at idling speed;

the machine must be switched oﬀ immediate-

ly if signiﬁcant vibration or other damage is

detected; the cause of these faults must be

determined.

■ By checking the dimensions and other important

data of the spindle, you can avoid the spindle

end touching the bottom of the opening of

grinding pots, cones or die grinders with thread-

ed inserts intended for mounting on machine

spindles.

■ For abrasive media which are supplied with re-

ducers or bushings or which are to be used with

reducers or bushings, the user must ensure that

the reducer or bushings do not touch the face of

the clamping ﬂange and that the clamping force

provides suﬃcient rotational drive to prevent the

abrasive from slipping.

■ In cases where clamping ﬂanges are provided

for diﬀerent types and sizes of abrasives, always

attach the correct clamping ﬂange for the abra-

sive medium being used.

■ Avoid direct contact before and after using the

machine tool, as it may be warm or sharp.

■ The abrasive medium must be stored and hand-

led in accordance with the manufacturer's

instructions.

Hazards in the workplace

■ Slipping, tripping and falling are the main

causes of injuries in the workplace. Look out

for surfaces which could have become slippery

due to use of the machine, and also any tripping

hazards caused by air or hydraulic hoses.

■ Proceed with caution in unknown surroundings.

Hidden hazards caused by power or other supply

lines may be present.

■ The abrasive grinding machine is not intended

for use in explosive atmospheres and is not

insulated against contact with electrical power

sources.

■ Make sure that there are no electrical lines, gas

pipelines, etc., which could lead to a hazard

in the event of damage due to the use of the

machine.

Hazards caused by dust and vapours

■ The dusts and vapours generated by the use

of sanding machines for abrasive sheets and

polishers can cause health problems (such as

cancer, birth defects, asthma and/or dermati-

tis); it is essential to carry out a risk assessment

of these hazards and to implement appropriate

control mechanisms.

■ The risk assessment should include all dust

caused by use of the machine and any existing

dust which may be kicked up at the same time.

■ The abrasive grinding machine is to be operated

and maintained in accordance with the recom-

mendations contained in this manual to keep

the release of dust and vapours to a minimum.

■ The exhaust air should be routed so that the

raising of dust in already dusty environments is

kept to a minimum.

PDTS 6.3 B3

■ 6

│

GB

│

CY

■ If dusts or vapours are created, the main priority

must be to control these at the site of their re-

lease.

■ All inserts or accessories of the machine in-

tended for collecting, extracting or suppressing

airborne dust or vapours or should be used and

serviced in accordance with the manufacturer’s

instructions.

■ Consumables/machine tools should be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid unnecessary intensiﬁcation of dust or

vapour production.

■ Use breathing equipment as per the instructions

provided by your employer or as required by

health and safety regulations.

■ The processing of certain materials can cause

the production of dust and vapours which can

lead to the formation of a potentially explosive

atmosphere.

Hazards caused by noise

■ Excessive noise levels in conjunction with insuﬃ-

cient hearing protection may lead to permanent

hearing damage, hearing loss and other prob-

lems, such as tinnitus (ringing, buzzing, whistling

or humming in your ears).

■ Suitable regulatory mechanisms include meas-

ures such as the use of insulation materials to

avoid pinging occurring on the workpieces.

■ Use hearing protection equipment.

■ The abrasive grinding machine is to be oper-

ated and maintained in accordance with the

recommendations contained in this manual to

reduce any unnecessary increase of the noise

levels.

■ If the abrasive grinding machine is equipped

with a silencer, always ensure that it is in its

place and in working order when the machine

is in operation.

■ Consumables/machine tools should be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid unnecessary increase of the noise levels.

Hazards caused by vibrations

■ Vibrations can damage the nerves and cause

malfunctions to the blood circulation in the

hands and arms.

■ When working in a cold environment, wear

warm clothing and keep your hands warm

and dry.

■ If you experience numbness, tingling or pain

in your ﬁngers or hands, or if the skin on your

ﬁngers or hands turns white, stop using the

abrasive grinding machine, inform your

employer and consult a doctor.

■ The abrasive grinding machine is to be oper-

ated and maintained in accordance with the

recommendations contained in this manual to

reduce any unnecessary increase of the vibra-

tions.

■ Do not allow the machine tool to rattle against

the workpiece, as this is highly likely to lead to

a considerable increase in vibrations.

■ Consumables/machine tools should be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid unnecessary increase of the vibrations.

■ Always use a stand, a clamp or a compensation

device to support the weight of the machine.

■ Hold the machine securely but not too ﬁrmly

while maintaining the necessary hand-reaction

force, as the vibration risk generally increases

the harder the machine is held.

■ Use intermediate layers if they are intended for

bonded abrasives.

Additional safety instructions for

pneumatic machines

■ Compressed air can cause serious injuries.

– Ensure that the air supply is switched oﬀ,

the hose is not under pressure, that the air

supply has been shut oﬀ and that the ma-

chine is disconnected from the air supply

when not in use, and also before exchang-

ing accessories or carrying out repairs.

– Never aim the airﬂow towards yourself or

any other person.

PDTS 6.3 B3

GB

│

CY

│

7 ■

■ Thrashing hoses can cause serious injury. There-

fore, always check that the hoses and their ﬁx-

ings are not damaged or have not come loose.

■ If universal rotary joints (claw couplings) are

used, locking pins must be used to provide pro-

tection; Whipcheck® air hose restraints must be

used to provide protection in case of a failure of

the connection of the hose to the machine.

■ Ensure that the maximum permissible pressure

on the machine is not exceeded.

■ Never carry compressed-air-powered machines

by the hose.

Special safety instructions for

grinding and abrasive cutting

■ Only use the grinding tools approved for your

compressed air tool and the blade guard provid-

ed for these grinding tools. Grinding tools which

are not intended for the compressed air tool

cannot be adequately shielded and are unsafe.

■ Oﬀset grinding discs must be mounted in such

a way that their grinding surface does not

project above the plane of the blade guard

edge. An improperly ﬁtted grinding disc which

protrudes over the level of the blade guard

edge cannot be properly guarded.

■ The blade guard must be securely attached

to the compressed air tool and adjusted for

maximum safety so that the minimum possible

amount of the abrasive medium is open to the

operator. The blade guard is designed to pro-

tect the operator from fragments and accidental

contact with the grinding tool.

■ Grinding tools should only be used for the

recommended applications. For example:

Never grind with the side surface of a cutting

disc. Cutting discs are designed to remove

material with the edge of the disc. Any lateral

application of force on these grinding tools can

lead to a breakage.

■ Always use undamaged clamping ﬂanges of

the correct size and shape for the grinding

wheel you have selected. Suitable ﬂanges

support the grinding disc and reduce the risk of

a disc breakage. Flanges for cutting discs can

be diﬀerent to ﬂanges for other grinding discs.

■ Do not use worn grinding wheels from larger

pneumatic tools. Grinding wheels for larger

compressed air tools are not designed for the

higher speeds of smaller compressed air tools

and may break.

Additional special safety instructions

for abrasive cutting

■ Avoid blocking the cutting disc or excessive

contact pressure. Do not make any exces-

sively deep cuts. Overloading the cutting disc

increases the stress and likelihood of tilting or

blocking and thus the possibility of a setback or

a breakage of the grinding tool.

■ Avoid the area in front of and behind the

rotating cutting disc. When you move the cut-

ting disc away from yourself in the workpiece it

is possible that, in the event of a kickback, the

compressed air tool might be thrown out direct-

ly towards you along with the rotating disc.

■ If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to a kickback. Identify and

remove the cause of the jam.

■ Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc can jam,

jump out of the workpiece or cause a kickback.

■ Support panels or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides of the disc:

both in the vicinity of the cutting disc and also

at the edge.

■ Cutting discs must be stored and handled care-

fully and in accordance with the manufacturer's

instructions.

PDTS 6.3 B3

■ 8

│

GB

│

CY

Kickback and corresponding safety

instructions

■ Kickback is a sudden reaction caused when a

rotating accessory tool catches or jams,

■ Catching or jamming causes the rotating acces-

sory tool to stop abruptly. If this happens, an

uncontrolled compressed air tool turns rapidly

against the direction of rotation of the accesso-

ry tool caught in the blockage.

■ If, for example, a grinding disc catches or

blocks in a workpiece, the edge of the grinding

disc which is projecting into the workpiece can

get caught and break oﬀ the grinding disc or

cause a kickback. The grinding disc can then

ﬂy in the direction of the operator or away from

him, depending on the direction of rotation of

the disc at the blockage.

This can also break grinding discs.

■ A kickback is caused by incorrect use or misuse

of the pneumatic tool. This can be avoided by

taking proper precautions as given below.

a) Hold the compressed air tool ﬁrmly in both

hands and position your body and arms so they

can absorb the force of a kickback. Always use

the additional handle, if available, so that you

have the maximum control over the kickback

force or reaction forces at full speed. By taking

adequate precautions, the operator can stay in

control of the kickback and reaction forces.

b) Never hold your hand close to a rotating

accessory tool. The accessory tool could jump

out of your hand if there is a kickback.

c) Avoid having any part of your body in the

region in which the compressed air tool is likely

to move in event of a kickback. The kickback

will force the compressed air tool in the oppo-

site direction to the direction of rotation of the

grinding disc at the blockage.

d) Take special care when working around

corners, sharp edges, etc. Avoid allowing the

accessory tool to bounce back from the work-

piece or jam. The rotating accessory tool is

more likely to jam in corners or sharp edges or

if it bounces. This can cause a loss of control or

kickback.

e) Do not use chains or toothed saw blades.

Such accessories often cause a kickback or loss

of control over the power tool.

Before use

Changing the cutting disc

ATTENTION!

► Disconnect the compressed air tool from the

compressed air supply before replacing the

insert tool or accessories or performing any

adjustment or maintenance. The spindle

must be at a standstill.

NOTE

► Only use original Parkside cutting discs.

♦ Counter the spindle

with the supplied open-

ended spanner (see also ﬁgure A on the

fold-out page).

♦ Use the supplied hex key

to remove the

clamping screw and the clamping ﬂange .

♦ Replace the cutting disc

. Mount the clamp-

ing ﬂange again and the clamping screw

with the hex key.

♦ Check whether the cutting disc

is ﬁrmly ﬁtted

and can rotate freely.

PDTS 6.3 B3

GB

│

CY

│

9 ■

Setting up

Lubrication

WARNING!

► Avoid eye and skin contact with lubricants.

NOTE

► Regular lubrication is particularly important

to avoid friction and corrosion damage.

We recommend using a suitable special oil

for compressed air tools (e.g. Liqui Moly

compressor oil).

– Lubrication with mist oiler

A mist oiler (not supplied) continuously

and optimally lubricates the grinder as

a preparation stage after the pressure

reducer. A mist oiler gives oﬀ ﬁne drops of

oil into the air ﬂow and thus guarantees a

regular lubrication.

– Manual lubrication

If you do not have a mist oiler, lubricate the

tool before every use or during longer work

sessions. Add 3–5 drops of pneumatic oil

into the connector nipple

.

Connecting to a compressed

airsource

NOTE

► Before connecting the compressed air source

– the correct working pressure (6.3 bar)

must be fully reached, and

– you must ensure that the trigger is in the

upper position.

► Use only connection hoses with an internal

diameter of at least 9 mm.

► Use only ﬁltered, lubricated and regulated

compressed air.

♦ Attach the tool to a compressor by connecting

the connector nipple

to the supply hose on

the compressed air source.

ATTENTION!

► Ensure that the compressed air hose is ﬁrmly

attached. A loose hose can thrash about

uncontrollably, causing serious danger.

Likewise, ensure ﬁrm seating of the two screw

connections between the coupling piece and

the tool.

♦ To ensure that you can regulate the air pressure,

the compressed air source must be equipped

with a pressure reducer.

Switching on and oﬀ

Switching on

♦ Press the switch-on guard

in the direction of

the blade guard . Then press the trigger to

turn on the appliance.

Switching oﬀ

♦ Release the trigger

.

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

Maintenance and cleaning

WARNING! RISK OF INJURY!

Disconnect the appliance from

the compressed air supply.

ATTENTION!

► Before maintenance, clean oﬀ any hazardous

substances which may have accumulated on

the tool (due to working processes). Avoid

all skin contact with these substances. If the

skin comes into contact with hazardous dusts,

this can lead to severe dermatitis. If dust is

produced or swirled up during maintenance,

it can be inhaled.

NOTE

► To ensure correct functioning and long-term

durability of the appliance, pay attention to

the following points:

■ Suﬃcient and continuous oil lubrication is highly

important for optimum functioning.

■ Check the speed and vibration levels after each

use.

PDTS 6.3 B3

■ 10

│

GB

│

CY

■ If the tool is exhibiting excessive vibration levels,

the cause of the vibrations must be identiﬁed

and repaired.

■ Check the spindles, threads and ﬁxtures regularly

for wear and tolerances for attaching abrasive

media.

■ Use only the genuine replacement parts rec-

ommended by the manufacturer, otherwise you

could put users at risk. In doubt, contact the

Service Centre.

■ Keep the compressed air appliances in a clean

condition. Clean the appliance with a soft, dry

cloth only.

■ Never use sharp or abrasive cleaning agents.

■ The compressed air tool should be stored in dry

rooms. Make sure that no moisture gets inside

the compressed air tool.

Disposal

The packaging consists of environmen-

tally friendly material. It can be dis-

posed of in local recycling containers.

Do not dispose of the appliance in the normal

domestic waste!

Your local community or municipal authorities

can provide information on how to dispose of the

worn-out appliance.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The packag-

ing material is labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

Dispose of lubricants and cleaning agents in an

environmentally friendly manner. Observe the legal

regulations.

■ Dispose of lubricant residues at a disposal

point. Do not allow lubricants to enter drains or

watercourses. Do not allow them to get into the

subsoil/soil. Make sure you use a suitable mat/

surface. Dispose of lubricants in accordance

with oﬃcial regulations.

■ Dispose of contaminated maintenance material

and consumables at a collection point provided

for this purpose.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase (re-

ceipt) within the three-year warranty period, along

with a brief written description of the fault and of

when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

PDTS 6.3 B3

GB

│

CY

│

11 ■

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches, batteries or parts made of

glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating instruc-

tions for the product regarding proper use of the

product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be pro-

vided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about

what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly

to the Lidl service page (www.lidl-service.com)

where you can open your operating instructions by

entering the item number (IAN) 123456.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 327364_1904

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PDTS 6.3 B3

■ 12

│

GB

│

CY

Original declaration of conformity

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

Applied harmonised standards

EN ISO 11148-7: 2012

Type designation of machine

Air Cut Oﬀ Tool PDTS 6.3 B3

Year of manufacture: 09 - 2019

Serial number: IAN 327364_1904

Bochum, 19/09/2019

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

PDTS 6.3 B3

RS

│

13 ■

Sadržaj

Uvod ..........................................................14

Namenska upotreba ........................................................ 14

Oprema .................................................................. 14

Obim isporuke ............................................................. 15

Tehnički podaci ............................................................15

Opšta bezbednosna pravila .......................................15

Opasnosti od izbačenih delova ................................................15

Opasnosti od zaplitanja ...................................................... 16

Opasnosti u radu ...........................................................16

Opasnosti od ponovljenih pokreta ..............................................16

Opasnosti od delova pribora .................................................. 17

Opasnosti na radnom mestu ..................................................17

Opasnosti od prašine i isparenja ...............................................17

Opasnosti od buke ..........................................................18

Opasnosti od vibracija ....................................................... 18

Dodatne bezbednosne napomene zapneumatske mašine ...........................19

Posebne bezbednosne napomene zabrušenje i sečenje .............................19

Posebne bezbednosne napomene uvezi sa sečenjem ..............................19

Povratni udar i odgovarajuće bezbednosne napomene .............................20

Pre puštanja u rad ...............................................20

Zamena rezne ploče ........................................................20

Puštanje u rad ...................................................21

Podmazivanje ..............................................................21

Priključak na izvor komprimovanog vazduha ...................................... 21

Uključivanje i isključivanje .................................................... 21

Održavanje i čišćenje .............................................21

Odlaganje ......................................................22

Garancija I Garantni List ..........................................22

Prevod originalne Izjave o usklađenosti .............................24

PDTS 6.3 B3

■ 14

│

RS

PNEUMATSKA REZNA

BRUSILICA PDTS 6.3 B3

Uvod

Čestitamo Vam na kupovini Vašeg novog uređaja.

Time ste se odlučili za kvalitetan proizvod. Uputstvo

za upotrebu je deo ovog proizvoda. Ono sadrži

važne napomene o bezbednosti, upotrebi i od-

laganju. Pre korišćenja proizvoda, upoznajte se

sa svim napomenama vezanim za rukovanje i bez-

bednost. Koristite proizvod samo na opisani način

i u navedene svrhe. Predajte svu dokumentaciju

prilikom prosleđivanja proizvoda trećim licima.

Namenska upotreba

Pneumatski alat je predviđen za sečenje tankih

metalnih limova, bez upotrebe vode. Svaka druga

upotreba ili promena mašine, smatra se nenamen-

skom i krije znatne opasnosti od nezgoda.

Uređaj nije namenjen za komercijalnu upotrebu.

Objašnjenje simbola:

WARNING!

Pre puštanja u rad pročitajte uputstvo

za upotrebu.

Nosite zaštitne naočare!

Smer rotacije

Vršite svakodnevno podmazi vanje

uljem!

11/2019. Datum proizvodnje

11/ 2 0 21.

Rok trajanja (vidljivo na unutrašnjem

metalnom prstenu)

Pre puštanja u rad, pročitajte

originalno uputstvo za upotrebu

i bezbednosne napomene.

Nosite štitnike za sluh!

Nosite zaštitne cipele!

Nosite zaštitne rukavice!

Nosite masku za zaštitu od prašine!

Nije dozvoljeno vlažno brušenje

Upotreba oštećenih reznih ploča

iploča za grubu obradu je opasna

i može da dovede do povreda sa

dalekosežnim posledicama!

Predviđeno za brušenje metala

75

Prečnik ploče

Nije dopušteno za bočno brušenje

pneumatska rezna brusilica

Oprema

Osigurač za uključivanje

Okidač

Štitnik

Stezni vijak

Stezna prirubnica

Rezna ploča

Imbus-ključ

Vreteno

Viljuškasti ključ

Utična glava 1/4“

PDTS 6.3 B3

RS

│

15 ■

Obim isporuke

1 pneumatska rezna brusilica

1 rezna ploča Ø 75 mm (prethodno montirana)

1 viljuškasti ključ

1 imbus-ključ

1 utična glava (1/4“) (prethodno montirana)

1 uputstvo za upotrebu

Tehnički podaci

Nominalni broj obrtaja: 20300 U/min

-1

Nominalni pritisak vazduha: maks. 6,3 bara

Dimenzije ploče: Ø 75 x 1 x 10 mm

Dimenzije vretena: M6

Utična glava: 1/4“

Težina: oko 0,69 kg

Vrednosti emisije buke:

Merna vrednost za buku je utvrđena u skladu

sa ISO15744:

Nivo zvučnog pritiska: L

pA

= 93,6 dB (A)

Odstupanje: K

pA

= 3 dB (A)

Nivo zvučne snage: L

WA

= 104,6 dB (A)

Odstupanje: K

WA

= 3 dB

Vrednost emisije vibracija:

Ukupna vrednost vibracija je utvrđena u skladu

sa ISO 28927-4 i EN 12096:

a

h

=3,06 m/s

2

Odstupanje K = 0,53 m/s

2

NAPOMENA

Ovim znakom se potvrđuje, da je

ovaj uređaj u skladu sa srpskim za-

htevima za bezbednost proizvoda.

WARNING!

Opšta bezbednosna

pravila

UPOZORENJE!

► Za višestruke opasnosti: Bezbednosne na-

pomene morate da pročitate i razumete pre

instalacije, upotrebe, popravke, održavanja i

zamene delova pribora na brusilici za brusne

nastavke, kao i pre radova u blizini mašine.

Ukoliko to nije slučaj, to može da dovede do

teških telesnih povreda.

■ Brusilicu za sredstva za brušenje treba da pri-

ključe, podese ili koriste isključivo odgovarajući

kvaliﬁkovani i obučeni rukovaoci.

■ Nisu dozvoljene izmene na mašini. Izmene

mogu da smanje eﬁkasnost bezbednosnih mera

i da povećaju rizike za rukovaoca.

■ Bezbednosne napomene ne smeju da se

izgube- dajte ih rukovaocu.

■ Nikada ne koristite oštećene brusilice za rad

sa sredstvima za brušenje.

■ Mašine moraju da se podvrgnu redovnom pre-

gledu, radi provere da je pneumatska brusilica

sekač označena jasno čitljivim nominalnim vred-

nostima i oznakama iz ovog dela ISO 11148.

Poslodavac/korisnik mora da stupi u kontakt sa

proizvođačem, da bi dobio dodatne oznake,

ako je potrebno.

Opasnosti od izbačenih delova

■ Prilikom loma radnog predmeta ili delova pribora,

ili čak samog alata mašine, delovi mogu da

budu izbačeni velikom brzinom.

■ Prilikom rada brusilice sa sredstvima za bruše-

nje, uvek mora da se nosi zaštita za oči, koja

je otporna na udar. Nivo neophodne zaštite bi

trebalo da se zasebno proceni za svaku pojedi-

načnu upotrebu.

■ Pobrinite se da radni predmet bude bezbedno

pričvršćen.

■ Pobrinite se da sredstvo za brušenje bude bez-

bedno stegnuto u brusilici za brusna sredstva.

PDTS 6.3 B3

■ 16

│

RS

■ Proverite da maksimalni radni broj obrtaja

sredstva za brušenje, preračunato u obrtaje u

minuti, bude isti ili veći od nominalnog broja

obrtaja vretena.

■ Uverite se da je štitnik montiran, da je u dobrom

stanju, da je propisno pričvršćen i da se redovno

kontroliše.

■ Pod pretpostavkom da radni predmet obuhvata

sredstvo za brušenje, moguće je, da štitnik neće

biti potreban za brušenje iznutra.

■ Proverite da li se stezne prirubnice koriste pre-

ma podacima proizvođača i da li su u dobrom

stanju, npr. bez naprslina i pukotina, i da su

ravne.

■ Proverite da li su vreteno i navoj vretena ošteće-

ni ili istrošeni.

■ Pobrinite se da varnice i odlomci, koji nastaju

pri upotrebi, ne izazovu opasnost.

■ Pre zamene sredstva za brušenje i pre održava-

nja, brusilica mora da se odvoji od napajanja

energijom.

Opasnosti od zaplitanja

■ Ako široku odeću, nakit, ogrlice, kosu ili rukavice

ne držite podalje od mašine i njenih delova

pribora, onda može da postoji opasnost od

gušenja, skalpiranja i/ili posekotina.

Opasnosti u radu

■ Izbegavajte kontakt sa rotirajućim vretenom i

montiranom brusnom pločom, da biste izbegli

posekotine na šakama ili drugim delovima tela.

■ Prilikom rada mašine, šake rukovaoca mogu

da budu izložene opasnostima, kao što su npr.

posekotine, ogrebotine i toplota. Nosite odgo-

varajuće rukavice kao zaštitu za šake.

■ Rukovalac i osoblje za održavanje moraju ﬁzički

da budu u stanju da rukuju veličinom, masom i

snagom mašine.

■ Držite mašinu pravilno:

Budite spremni da se suprotstavite uobičajenim

ili iznenadnim pokretima. Obe šake treba da

Vam budu spremne.

■ Vodite računa o tome da Vaše telo bude u

ravnoteži i da imate stabilan položaj.

■ Omogućite komandnom uređaju da se pokrene

i zaustavi u slučaju prekida u snabdevanju

energijom.

■ Koristite samo preporučena sredstva za podmazi-

vanje.

■ Zaštitne naočare moraju da se nose, preporuču-

je se nošenje zaštitnih rukavica i zaštitne odeće.

■ Prilikom radova iznad glave, nosite zaštitni šlem.

■ Nakon isključivanja, mašinu odložite tek kada

se ploča zaustavi.

■ Kod sečenja, radni predmet mora da se podupre,

tako da tokom celokupne obrade prorez ima

konstantnu ili rastuću širinu;

■ Ukoliko se sredstvo za brušenje zaglavi u pro-

rezu, brusilica na kojoj je to sredstvo mora da

se isključi, a brusna ploča mora da se olabavi.

Pre nastavljanja sa radom, mora da se proveri

da li je sredstvo za brušenje još uvek propisno

pričvršćeno i da nije oštećeno;

■ Brusne ploče i ploče za rezanje brušenjem ne

smeju da se upotrebljavaju za bočno brušenje

(izuzetak: brusne ploče za bočno brušenje).

Brusilice za sredstva za brušenje ne smeju da se

upotrebljavaju sa većim obimnim brojem obrta-

ja od maksimalno dozvoljenog za sredstva za

brušenje;

■ Uverite se da u neposredoj blizini nema ljudi

koji stoje okolo.

■ Mora da se koristi lična zaštitna oprema, kao

što su odgovarajuće rukavice, kecelje i zaštitni

šlem.

■ Varnice koje nastaju brušenjem, mogu da zapale

odeću i da izazovu teške opekotine. Pobrinite se

da varnice na padaju na odeću. Nosite sporo-

goreću odeću i pobrinite se da kofa sa vodom

bude u blizini.

Opasnosti od ponovljenih pokreta

■ Kada se koristi brusilica sa sredstvima za bru-

šenje, rukovalac može u toku obavljanja radnih

aktivnosti da bude izložen neprijatnom osećaju

u šakama i rukama, kao i u području vrata i

ramena ili na drugim delovima tela.

■ Kada se koristi brusilica sa sredstvima za bru-

šenje, rukovalac bi trebalo da zauzme udoban

položaj tela, pri čemu treba da vodi računa o

PDTS 6.3 B3

RS

│

17 ■

stabilnom položaju i da izbegne nepovoljne

položaje tela ili one kod kojih se teško drži

ravnoteža. U toku dugotrajnog rada, rukovalac

bi trebalo da promeni položaj tela, što može

da pomogne u izbegavanju neprijatnosti i za-

maranja.

■ Ukoliko rukovalac na sebi primeti simptome,

kao npr. trajna ili ponovna nelagodnost, tego-

be, lupanje, bol, trnjenje, obamrlost, pečenje ili

ukočenost, ne bi trebalo da ignoriše te znakove.

Rukovalac bi trebalo da to saopšti poslodavcu i

da se obrati kvaliﬁkovanom medicinskom radni-

ku za pomoć.

Opasnosti od delova pribora

■ Pre montaže ili zamene alata mašine ili delova

pribora, odvojite brusilicu sa sredstvom za bru-

šenje od napajanja energijom.

■ Koristite isključivo delove pribora i potrošni

materijal prema veličini i tipu koje je preporučio

proizvođač brusilice za sredstva za brušenje.

Ne koristite druge tipove ili veličine delova

pribora i potrošnog materijala.

■ Pobrinite se da dimenzije sredstva za brušenje

odgovaraju dimenzijama brusilice za sredstva

za brušenje i da sredstvo za brušenje odgovara

vretenu.

■ Pobrinite se da tip i veličina navoja sredstva za

brušenje tačno odgovaraju tipu i veličini navoja

vretena.

■ Pre upotrebe, izvršite kontrolu sredstva za bru-

šenje. Ne upotrebljavajte sredstva za brušenje

koja su možda ispala ili na kojima postoje

odlomci, naprsline ili druge greške.

■ Pobrinite se da je sredstvo za brušenje, pre

upotrebe, propisno i dovoljno snažno pričvršće-

no; brusilica za sredstva za brušenje mora, u

bezbednom položaju, da radi najmanje 1 min

sa brojem obrtaja u praznom hodu; mašina

mora odmah da se isključi, kada se primete

znatne vibracije ili druga oštećenja; mora da

se ustanovi uzrok tih grešaka.

■ Proverom dimenzija i ostalih važnih podataka

o vretenu, izbegava se da kraj vretena dodiruje

dno otvora brusnih lonaca, brusnih konusa ili

brusnih nastavaka sa navojnim umetkom, koji su

predviđeni za montažu na vreteno mašine;

■ Kod brusnih sredstava koja se isporučuju sa

adapterima ili redukcionim čaurama, ili koja

treba da se koriste sa adapterima ili redukcio-

nim čaurama, korisnik mora da se pobrine da

adapter ili redukciona čaura ne dodiruju čeonu

stranu stezne prirubnice i da zbog stezne sile

postoji dovoljan rotacioni pogon, da bi se izbe-

glo iskliznuće sredstva za brušenje.

■ U slučajevima kada su na raspolaganju stezne

prirubnice za različite tipove i veličine sredstava

za brušenje, uvek pričvrstite ispravnu steznu

prirubnicu za korišćeno sredstvo za brušenje.

■ Pre i nakon upotrebe mašinskog alata, izbega-

vajte direktan kontakt, jer isti može biti vruć ili

oštrih ivica.

■ Sredstvo za brušenje mora da se skladišti i

njime mora da se rukuje prema uputstvima

proizvođača.

Opasnosti na radnom mestu

■ Proklizavanje, spoticanje i pad su glavni ra-

zlozi za povrede na radnom mestu. Vodite ra-

čuna o površinama koje usled korišćenja mašine

mogu da postanu klizave, i o povredama usled

spoticanja, koje su prouzrokovane crevima za

vazduh i hidrauličnim crevima.

■ Krećite se oprezno u nepoznatom okruženju.

Mogu da postoje skrivene opasnosti od električ-

nih kablova ili ostalih vodova za snabdevanje.

■ Ova brusilica za sredstva za brušenje nije pred-

viđena za korišćenje u eksplozivnim atmosfera-

ma i nije izolovana od kontakta sa električnim

izvorima napajanja.

■ Uverite se da ne postoje električni vodovi, gaso-

vodi itd. koji bi, u slučaju oštećenja usled kori-

šćenja mašine mogli da dovedu do opasnosti.

Opasnosti od prašine i isparenja

■ Prašine i isparenja koja nastaju tokom kori-

šćenja brusilica za brusne listove i uređaja za

poliranje, mogu da izazovu zdravstvene tegobe

(kao npr. rak, urođene mane, astmu i/ili der-

matitis); neophodno je da se sprovede procena

rizika u pogledu tih opasnosti i da se realizuju

odgovarajući mehanizmi regulisanja.

Pagina se încarcă ...

Parkside PDTS 6.3 B3 Translation Of The Original Instructions

Parkside PDTS 6.3 B3 Translation Of The Original Instructions

în alte limbi

Lucrări conexe

Alte documente