Parkside PWSA 20-Li C3 Instrucțiuni de utilizare

Categorie
Unelte electrice
Tip
Instrucțiuni de utilizare
CORDLESS ANGLE GRINDER PWSA 20-Li C3
IAN 360196_2007
AKKU-WINKELSCHLEIFER
Originalbetriebsanleitung
CORDLESS ANGLE GRINDER
Translation of the original instructions
АКУМУЛАТОРЕН ЪГЛОШЛАЙФ
Превод на оригиналното ръководство за експлоатация
POLIZOR UNGHIULAR
Traducerea instrucţiunilor de utilizare original
ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟΣ
ΓΩΝΙΑΚΟΣ ΤΡΟΧΟΣ
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
AKU KUTNA BRUSILICA
Prijevod originalnih uputa za uporabu
AKU UGAONA BRUSILICA
Prevod originalnog uputstva za upotrebu
GB / CY Translation of the original instructions Page 1
HR Prijevod originalnih uputa za uporabu Stranica 19
RS Prevod originalnog uputstva za upotrebu Strana 37
RO Traducerea instrucţiunilor de utilizare original Pagina 55
BG Превод на оригиналното ръководство за експлоатация Cтраница 73
GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 95
DE / AT / CH Originalbetriebsanleitung Seite 115
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Rasklopite prije čitanja obije stranice sa slikama i nakon toga se upoznajte sa svim funkcijama uređaja.
Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.
Înainte de a citi instrucţiunile, priviţi ambele pagini cu imagini şi familiarizaţi-vă cu toate funcţiile aparatului.
Преди да прочетете отворете двете страници с фигурите и след това се запознайте с всички
функции на уреда.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.
B
A
DC
E E
8a X
20V max.
18V
All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3/ PLG 20 A4/
PDSLG 20 A1 of the X20V Team series are compatible with the PAP 20 A1/PAP 20 A2/
PAP 20 A3/ PAP 20 B1/ PAP 20 B3 battery pack.
Charging times
Charging currents
2 Ah
Battery pack
PAP 20 A1/B1
3 Ah
Battery pack
PAP 20 A2
4 Ah
Battery pack
PAP 20 A3/B3
max. 2.4 A
Charger PLG 20 A1/A4
60 min
2,4 A
90 min
2,4 A
120 min
2,4 A
max. 3.5 A
Charger PLG 20 A2
45 min
3,5 A
60 min
3,5 A
80 min
3,5 A
max. 4.5 A
Charger PLG 20 A3
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
max. 4.5 A
Charger PDSLG 20 A1
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
PWSA 20-Li C3 GBCY 1
Contents
Introduction ............................................................2
Intended use ........................................................................2
Features ...........................................................................2
Package contents ....................................................................3
Technical details .....................................................................3
General power tool safety warnings ....................................... 4
1. Work area safety ..................................................................4
2. Electrical safety ...................................................................4
3. Personal safety ....................................................................4
4. Power tool use and care ............................................................5
5. Use and handling of the cordless electrical power tool .....................................5
Safety instructions for all applications ....................................................6
Kickback and corresponding safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Special safety instructions for grinding and abrasive cutting ...................................8
Additional special safety instructions for abrasive cutting .....................................8
Safety guidelines for battery chargers ....................................................9
Permissible accessories ................................................................9
Storage and handling of the recommended accessory tools ..................................10
Working procedures .................................................................10
Before use ............................................................11
Charging the battery pack (seefig.A) ...................................................11
Attaching/disconnecting the battery pack to/from the appliance ..............................11
Checking the battery charge level ......................................................11
Fitting the protective cover for cutting ....................................................11
Adjusting the blade guard ............................................................12
Fitting the additional handle ...........................................................12
Fitting/changing the roughing/ cutting disc ...............................................12
Operation ............................................................13
Switching on and off ................................................................13
Adjusting the rotational speed .........................................................13
Maintenance and cleaning ...............................................14
Disposal ..............................................................14
Kompernass Handels GmbH warranty ....................................15
Service ...............................................................16
Importer .............................................................16
Translation of the original Conformity Declaration ...........................17
Ordering a replacement battery ..........................................18
Telephone ordering .................................................................18
PWSA 20-Li C3
2 GBCY
CORDLESS ANGLE GRINDER
PWSA 20-Li C3
Introduction
Congratulations on the purchase of your new
appliance. You have chosen a high-quality product.
The operating instructions are part of this product.
They contain important information about safety,
usage and disposal. Before using the product,
please familiarise yourself with all operating and
safety instructions. Use the product only as
described and for the range of applications speci-
fied. Please also pass these operating instructions
on to any future owner.
Intended use
The appliance is intended for cutting, rough cutting
and brushing metal, concrete or tiles without the
use of water. Any other usage or modification of
the appliance is deemed to be improper and carries
a significant risk of accidents. The manufacturer
accepts no responsibility for damage(s) resulting
from improper usage. The appliance is not intended
for commercial use.
Explanation of the symbols used
Before using the appliance for the first
time, read the original operating
instructions and safety instructions.
The use of damaged cutting or
polishing discs is dangerous and can
lead to serious injuries!
 Diameter of the disc
Cordless angle grinder
Wear protective goggles!
Wear ear muffs!
Wear safety shoes!
Wear protective gloves!
Wear a dust mask!
Not approved for wet grinding
Not approved for side grinding
Suitable for grinding metal
Features
ON/OFF switch
Release button for the battery pack
Battery pack*
Battery charge level button
Battery display LED
Adjusting wheel for speed pre-selection
Additional handle
Blade guard
Spindle locking button
Screw thread (3 x) for the additional handle
Mounting ring
Screws
Blade guard fixture
High-speed charger (see fig. A)*
Red charge control LED (see fig. A)
Green charge control LED (see fig. A)
Attachment spindle (see fig. C)
Attachment flange (see fig. C)
Clamping nut (see fig. C)
Two-hole mounting spanner (see fig. D)
Bulges
PWSA 20-Li C3 GBCY 3
Package contents
1 cordless angle grinder
1 additional handle
1 blade guard (pre-assembled)
1 two-hole mounting spanner
1 cutting disc (pre-assembled)
1 set of operating instructions
Technical details
Cordless angle grinder PWSA 20-Li C3
Rated voltage 20 V (DC)
Rated idle speed n 2500–10000 rpm
Disc width Ø 125 mm
Thread size M14
Battery PAP 20 A3*
Type LITHIUM ION
Rated voltage 20 V (DC)
Capacity 4 Ah
Cells 10
High-speed battery charger PLG 20 A3*
INPUT
Rated voltage 230–240 V ~,
50 Hz (AC)
Rated power consumption 120 W
Fuse (internal) 3.15 A T3.15A
OUTPUT
Rated voltage 21.5 V (DC)
Rated current 4.5 A
Charging time approx. 60 min
Protection class II / (double insulation)
* BATTERY AND CHARGER ARE NOT INCLUDED
Noise and vibration data
Noise measurement value determined in accord-
ance with EN 60745. The A-rated noise level of
the power tool is typically:
Noise emission value
Sound pressure level LPA = 83 dB(A)
Uncertainty K = 3 dB
Sound power level LWA = 94 dB(A)
Uncertainty K = 3 dB
Wear ear muffs!
Total vibration value
Surface grinding
main handle ah, AG = 2.698 m/s2
Uncertainty K = 1.5 m/s2
Surface grinding
Additional handle ah, AG = 3.284 m/s2
Uncertainty K = 1.5 m/s2
NOTE
The vibration level specified in these instruc-
tions has been measured in accordance with
a standardised measuring procedure and can
be used for equipment comparisons. The
specified vibration emission value can also
be used to make an initial exposure estimate.
WARNING!
The vibration level varies depending on the
use of the power tool and may be higher
than the value specified in these instructions
in some cases. Regular use of the power tool
in this way may cause the user to underesti-
mate the vibration. Try to keep the vibration
loads as low as possible. Measures to reduce
the vibration load are, e.g. wearing gloves
and limiting the working time. Wherein all
states of operation must be included (e.g.
times when the power tool is switched off and
times where the power tool is switched on but
running without load).
PWSA 20-Li C3
4 GBCY
General power tool
safety warnings
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e)
When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b)
Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate condi-
tions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
PWSA 20-Li C3 GBCY 5
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use
of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tool’s operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery unit using
only the charger recommended by the manu-
facturer. Chargers are often designed for a
particular type of rechargeable battery unit.
There is the danger of fire if other types of
rechargeable battery units are used.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable batteries may
lead to a risk of injury or fire.
c) When they are not being used, store
rechargeable battery units away from paper-
clips, coins, keys, nails, screws or other small
metal objects that could cause the contacts to
be bridged. Short-circuiting the contacts of a
rechargeable battery unit may result in heat
damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens,
avoid contact with the fluid. If contact occurs,
flush the affected area with water. Seek addi-
tional medical help if any of the fluid gets into
your eyes. Escaping battery fluid may cause
skin irritation or burns.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries.
Protect the recharge-
able battery from heat (for example, from
continuous exposure to sunlight), fire, water
and moisture. There is a risk of explosion.
PWSA 20-Li C3
6 GBCY
Safety instructions for all
applications
Special safety instructions for grinding and
abrasive cutting
a) This power tool is to be used as a grinder and
abrasive cutting appliance. Please follow all
safety instructions, instructions, diagrams and
data that you receive with the appliance.
If you do not observe the following instructions,
this can lead to an electrical shock, fire and/or
serious injuries.
b) This power tool is not suitable for sandpaper
sanding, working with a steel brush or
burnishing. Using the power tool for applica-
tions for which it is not designed can lead to
hazards and injuries.
c) Do not use any accessories that have not been
specifically provided or recommended by the
manufacturer for this power tool. Just because
you can attach the accessories to your power
tool does not guarantee they are safe to use.
d) The maximum speed of the accessory tool
used must be at least as high as the maximum
speed specified for the power tool. Accessories
that rotate faster than the permissible rate can
break and throw pieces into the air.
e) The external diameter and thickness of the
accessory tool used must comply with the
dimensions of the power tool. Incorrectly
dimensioned accessory tools cannot be suffi-
ciently shielded or controlled.
f) Attachment tools with a thread insert must
match the thread of the grinding spindle
exactly. For attachment tools that are
mounted using a flange, the diameter of the
hole on the attachment tool must correspond
to the width of the fitment on the flange.
Accessory tools that cannot be fitted precisely
onto the power tool will rotate unevenly, vibrate
severely and can lead to a loss of control.
g) Never use damaged attachment parts. Check
accessory tools such as grinding discs before
each use for chips or cracks, grinding plates
for cracks, wearing or excessive wear and
tear and wire brushes for loose or broken
wires. If the power tool or the accessory tool
in use is dropped, check to see if it is
damaged or use an undamaged accessory
tool. When you have checked and inserted
the accessory tool, ensure that you and any
other people in the vicinity remain outside of
the level of the rotating accessory tool and
allow the tool to rotate at maximum speed for
one minute. Damaged accessories usually
break during the test period.
h) Wear personal protective equipment.
Depending on the application, ensure that
you use full face protection, eye protection or
goggles. Use a dust mask, hearing protec-
tion, protective gloves or special apron to
protect yourself from grindings and material
particles as required. Protect your eyes from
flying debris that may be created during certain
applications. Dust or filter masks must be used
to filter any dust created by the application. If
you are exposed to loud noise for any length
of time, you may suffer hearing loss.
i) Ensure that other people remain at a safe
distance from your workspace. Anyone who
enters the workspace must wear personal
protective equipment.
Fragments of the workpiece or broken acces-
sory tools can fly off and cause injury – even
outside the immediate working area.
j) Hold the power tool only by the insulated
handles when you are carrying out work in
which the accessory tool may come into
contact with concealed power cables. Contact
with a live cable can also make metal parts of
the appliance live and could result in an electric
shock.
k) Keep the power cord away from any rotating
accessories. If you lose control of the appli-
ance, the cord may get caught or cut and your
hand or arm could get caught in the rotating
accessory tool.
PWSA 20-Li C3 GBCY 7
l) Never put the power tool down until the
accessory tool being used has come to a
complete standstill. The rotating accessory tool
can come into contact with the surface and
cause you to lose control of the power tool.
m) Do not leave the power tool running whilst
carrying it. Accidental contact between your
clothing and the rotating accessory tool could
lead to physical injury.
n) Clean the ventilation slits of your power tool
regularly. The engine fan draws dust into the
housing and a strong accumulation of metal
dust can cause electrical hazards.
o) Never use the power tool in the vicinity of
inflammable materials. Sparks can ignite these
materials.
p) Do not use any accessory tools which require
liquid coolant. The use of water or other liquid
coolants may lead to electric shock.
Kickback and corresponding safety
instructions
Kickback is a sudden reaction caused when a
rotating accessory tool, e.g. grinding disc, grinding
plate, wire brush, etc., catches or jams. Catching or
jamming leads to an abrupt stop of the rotating
accessory tool. If this happens, an uncontrolled
power tool turns rapidly against the direction of
rotation of the accessory tool caught in the
blockage.
If, for example, a grinding disc catches or jams in a
workpiece, the edge of the grinding disc projecting
into the workpiece can get caught and break off
the grinding disc or cause a kickback. The grinding
disc can then fly in the direction of the operator or
away from him, depending on the direction of
rotation of the disc at the blockage. This can also
break grinding discs.
A kickback is caused by improper or incorrect use
of the power tool. This can be avoided by taking
proper precautions as described below.
a) Hold the power tool firmly in both hands and
position your body and arms so they can
absorb the force of a kickback. Always use
the additional handle, if available, so that
you have the maximum possible control over
the kickback force or reaction forces at full
speed. By taking adequate precautions, the
operator can stay in control of the kickback
and reaction torques.
b) Never hold your hand close to a rotating
accessory tool. The accessory tool could hit
your hand in the event of a kickback.
c) Avoid having any part of your body in the
region in which the power tool is likely to
move in event of a kickback. The kickback will
force the power tool in the opposite direction to
the direction of rotation of the grinding disc at
the blockage.
d) Take special care when working near corners,
sharp edges, etc. Avoid allowing the acces-
sory tool to bounce back from the workpiece
or jam. The rotating accessory tool is more
likely to jam in corners or sharp edges or if it
rebounds off them. This can cause a loss of
control or kickback.
e) Do not use chains or toothed saw blades.
Such accessories often cause a kickback or
loss of control over the power tool.
PWSA 20-Li C3
8 GBCY
Special safety instructions for
grinding and abrasive cutting
a)
Use only the grinding accessories approved for
your power tool and the appropriate blade
guard for these grinding tools. Grinding tools
which are not designed for the power tool
cannot be sufficiently shielded and are unsafe.
b)
Offset grinding discs must be fitted so that the
grinding surface does not protrude over the
level of the blade guard edge. An improperly
fitted grinding disc which protrudes over the
level of the blade guard edge cannot be prop-
erly guarded.
c) The blade guard must be securely mounted
on the power tool and adjusted to ensure
maximum safety so that the smallest possible
amount of the grinding tool is exposed to the
operator. The blade guard is designed to
protect the operator from fragments, accidental
contact with the grinding tool and sparks that
could ignite clothing.
d) Grinding tools should only be used for the
recommended applications. For example:
Never grind with the side surface of a cutting
disc. Cutting discs are designed to remove
material with the edge of the disc. Any lateral
application of force on these grinding tools can
lead to breakage.
e) Always use an undamaged clamping flange
of the correct size and shape for the selected
grinding disc. Suitable flanges support the
grinding disc and reduce the risk of disc
breakage. Flanges for cutting discs can be
different to flanges for other grinding discs.
f) Do not use worn grinding discs from larger
power tools. Grinding discs for larger power
tools are not designed for the higher rotational
speeds of smaller power tools and can break.
Additional special safety instructions
for abrasive cutting
a) Avoid any blockage to the cutting disc or
high contact pressure. Do not make any
excessively deep cuts. Overloading the cutting
disc increases the stress and likelihood of tilting
or jamming and thus the possibility of kickback
or breakage of the grinding tool.
b) Avoid the area in front of and behind the
rotating cutting disc. When you move the cutting
disc away from yourself in the workpiece, it is
possible, in the event of a kickback, that the
power tool along with the rotating disc might be
thrown out directly towards you.
b) If the cutting disc jams or you stop working,
switch the tool off and hold it steadily in the
workpiece until the disc has completely
stopped turning. Never attempt to pull a
rotating cutting disc out of a cut. This could
lead to kickback. Identify and remove the
cause of the jam.
d) Do not switch the power tool back on while it
is located in the workpiece. Allow the cutting
disc to reach its full speed before you care-
fully continue the cut. Otherwise, the disc can
jam, jump out of the workpiece or cause kick-
back.
e) Support boards or large workpieces to reduce
the risk of the cutting disc jamming and
causing a kickback. Large workpieces can bend
under their own weight. The workpiece must be
supported on both sides of the disc: both in the
vicinity of the cutting disc and also at the edge.
f)
Be particularly careful when making pocket
cuts into existing walls or other obscured
areas. The inserted cutting disc may cut into gas
or water pipes, electrical wiring or other objects
that can cause kickback.
PWSA 20-Li C3 GBCY 9
Safety guidelines for battery
chargers
This appliance may be used by
children aged 8 years and above
and by persons with limited phys-
ical, sensory or mental capabilities
or lack of experience and knowl-
edge, provided that they are under
supervision or have been told how
to use the appliance safely and are
aware of the potential risks. Do not
allow children to use the appliance
as a toy. Cleaning and user mainte-
nance tasks may not be carried out
by children unless they are super-
vised.
To avoid potential risks, damaged
mains cables should be replaced
by the manufacturer, their customer
service department or a similarly
qualified person.
The charger is suitable
for indoor use only.
WARNING!
To avoid potential risks, damaged mains
cables should be replaced by the manufac-
turer, their customer service department or a
similarly qualified person.
ATTENTION!
This charger can only charge the following
batteries: PAP 20 A1/PAP 20 A2/PAP 20 A3
.
A current list of battery compatibility can be
found at www.lidl.de/Akku.
Permissible accessories
Max. diameter Ø (mm)
Max. thickness (mm)
Thread size (mm)
Max speed (rpm)
Max. circumferential
speed (m/s)
Tool
Blade guard
Cutting disc 125 3 M14 12250 80 Two-hole mounting
spanner Yes
Roughing disc 125 6 M14 12250 80 Two-hole mounting
spanner Yes
PWSA 20-Li C3
10 GBCY
Storage and handling of the
recommended accessory tools
Grinding tools must be treated with care and
transported carefully.
Grinding tools should be stored in such a
way that they are not exposed to mechanical
damage or environmental influences (e.g.
damp).
Working procedures
NOTE
Grinding tools should only be used for the
recommended applications. Otherwise, they
can break, be damaged or cause injuries.
Rough grinding
Never use cutting discs
for rough grinding!
Move the angle grinder with moderate
pressure back and forth over the workpiece.
For soft material, move the roughing disc
at a flat angle over the workpiece; for hard
material at a slightly steeper angle.
Abrasive cutting
Never use roughing discs
for cutting!
Use only tested fibre-reinforced cutting or
grinding discs that are approved for a
peripheral speed of not less than 80 m/s.
CAUTION!
The grinder continues running after being
turned off. Do not try to brake it by applying
lateral counterpressure.
Secure the workpiece. Use clamps/a vice to
hold the workpiece firmly in place. This is much
safer than simply holding it in your hand.
Always switch off the appliance before
putting it down and wait for the appliance to
come to a complete standstill.
Use the appliance only for dry cutting or
sanding.
The additional handle must be mounted
on the appliance for all work.
Materials containing asbestos may not be
processed. Asbestos is a known carcinogen.
Tip! This symbol indicates
proper behaviour.
DANGER! ALWAYS GUIDE THE
APPLIANCE THROUGH THE WORK-
PIECE IN REVERSE ROTATION.
In the opposite direction there is a risk of
a kickback. The appliance can be pushed
out of the cut.
Always switch the appliance on before
applying it to the workpiece. After completing
the task, lift the appliance from the workpiece
and then switch it off.
Always hold the appliance firmly with two
hands while working. Ensure that your stance
is secure and stable.
For an optimum grinding effect, move the appli-
ance evenly at an angle of 15° to 30°
(between the grinding disc and workpiece)
backwards and forwards.
When working on angled surfaces, do not
exert great force on the workpiece. If the
rotational speed drops significantly, you must
reduce the pressure exerted to allow safe and
effective working. If the appliance suddenly
brakes completely or jams, it must be switched
off immediately.
Cutting: Work at a moderate feed rate and
do not tilt the cutting disc.
Roughing and cutting discs become very hot
– let them cool down completely before
touching them.
Never use the appliance for purposes other
than the ones for which it was designed.
Always make sure that the appliance is
turned off before inserting the battery into it.
In the event of danger, turn off the appliance
and remove the battery. Ensure that the appli-
ance is easily and quickly accessible in the
event of an emergency.
PWSA 20-Li C3 GBCY 11
Always remove the battery during work
breaks, when adjusting the appliance and
when it is not in use. The appliance must be
kept clean, dry and free of oil and grease at
all times.
Remain alert at all times! Always pay atten-
tion to what you are doing and act with
common sense. Do not use the appliance if
you are distracted or feeling unwell.
WARNING!
Always wear safety goggles.
WARNING!
Always wear a dust mask!
Before use
Charging the battery pack
(seefig.A)
CAUTION!
Always unplug the appliance before you
remove the battery pack from or connect
the battery pack to the charger.
NOTE
Never charge the battery pack if the ambient
temperature is below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should
be checked regularly. The optimum charge
level is between 50% and 80%. The storage
climate should be cool and dry and the
ambient temperature should be between 0°C
and 50°C.
Connect the battery pack to the high-speed
charger (see fig. A).
Insert the power plug into the socket. The
control LED lights up red.
The green LED indicates that the charging
process is complete and the battery pack is
ready.
ATTENTION!
If the red control LED flashes, this means
that the battery pack has overheated and
cannot be charged.
If the red and green control LEDs both
flash, this means that the battery pack is
defective.
Switch off the charger for at least 15 minutes
between successive charging sessions. Also
disconnect the power plug from the mains
power socket.
Attaching/disconnecting the battery
pack to/from the appliance
Attaching the battery pack
Allow the battery pack to click into the
handle.
Removing the battery pack
Press the release button and remove the
battery pack .
Checking the battery charge level
Press the battery charge level button to
check the status of the battery (see also main
diagram).
The status/remaining charge will be shown on
the battery display LED as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Fitting the protective cover for cutting
When cutting with bonded abrasives, always use
the protective cover 8a for cutting.
Slide the protective cover 8a onto the blade
guard (see fig. E) until the plastic clip “X”
snaps into place at the end.
When removing the protective cover 8a,
press the plastic clip “X” in slightly to release
the protective cover 8a.
PWSA 20-Li C3
12 GBCY
Adjusting the blade guard
WARNING! RISK OF INJURY!
Always switch the appliance off and remove
the battery before carrying out any work on
the appliance.
RISK OF INJURY!
Always use the angle grinder with the blade
guard . The blade guard should be
installed securely. Set it so that the highest
possible degree of safety is achieved, i.e.
the smallest possible part of the grinding
disc is exposed to the operator. The blade
guard is designed to protect the operator
from fragments and accidental contact with
the grinding tool.
RISK OF INJURY!
Make sure that the blade guard is fitted
at at least the same angle as the additional
handle (see fig. B). Otherwise, you could
injure yourself on the roughing disc or cutting
disc.
Turn the blade guard to the required position
(working position). Make sure that the blade
guard is positioned in such a way that the
blade guard fixture lies over one of the
5 bulges on the blade guard (see Fig. E
(fold-out page).
Ensure that the blade guard fixture is firmly
seated in the respective bulge .
Fitting the additional handle
CAUTION!
For safety reasons, this appliance may only
be used with the additional handle .
Failure to do so can lead to serious injury.
The additional handle can be screwed
onto the left, the right or the top, depending
on the job at hand.
Fitting/changing the roughing/
cutting disc
Always wear protective gloves when
changing cutting/rough grinding discs.
Pay attention to the dimensions of the roughing/
cutting disc. The diameter of the hole must fit the
attachment flange without any play. Do not use
a reducer or adapter.
NOTE
Use only discs which are free of dirt.
Use only grinding discs whose permissible
speed rating is at least as high as that on the
type plate on the power tool.
RISK OF INJURY! Press the spindle locking
button only when the attachment spindle
is at a complete standstill.
Press the spindle locking button to lock the
motor.
Undo the clamping nut using the two-hole
mounting spanner (see fig D).
Place the rough grinding or cutting disc with the
label side towards the appliance on the attach-
ment flange .
Then replace the clamping nut on the attach-
ment spindle with the raised side facing up.
PWSA 20-Li C3 GBCY 13
With thin grinding discs (see fig. 1)
The collar of the clamping nut faces upwards
so that a thin grinding disc can be fitted safely.
12
≤ 3,2 mm
Fig. 1
Press the spindle locking button to lock the
motor.
Tighten the clamping nut using the two-hole
mounting spanner .
With thick grinding discs (see fig. 2)
> 3,2 mm
Fig. 2
The collar of the clamping nut faces downwards
so that the grinding disk can be fitted securely onto
the attachment spindle .
Lock the attachment spindle .
Tighten the clamping nut in a clockwise
direction using the two-hole mounting
spanner .
NOTE
If the disc does not turn smoothly or vibrates
after the change, the disc must be replaced
immediately.
For safety's sake, run the appliance at maximum
speed for 60 seconds after every disc change.
Be aware of unusual noises and sparks.
Check whether all the fastening elements are
correctly fitted.
Make sure that the arrow showing the direction
of rotation (if any) on the cutting or rough
grinding discs (including diamond cutting discs)
and the direction of rotation of the appliance
(arrow showing the direction of rotation on the
head) match.
Operation
Switching on and off
Check the attached tool before use to ensure that
all fastening elements are correctly fitted.
NOTE
Always switch on the angle grinder before
making contact with the material, then apply
it to the workpiece.
Switching on:
First, press the ON/OFF switch to the right
so that you can then press it forwards.
Switching off:
Let go of the ON/OFF switch .
Switching to continuous operation:
First, press the ON/OFF switch to the right
so that you can then press it forwards. Then
press the ON/OFF switch forwards and
down until it engages.
Switching off continuous operation
Press the ON/OFF switch to the rear and
downwards and release it.
Adjusting the rotational speed
You can use the adjusting wheel for speed pre-
selection to preselect the rotational speed:
(1 = slower speed, 6 = faster speed).
We recommend you carry out practice tests to
determine the correct speed.
The speed can also be changed during operation.
PWSA 20-Li C3
14 GBCY
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off and remove
the battery before carrying out any
work on the appliance.
The battery angle grinder is maintenance-free.
Do not use any sharp objects for cleaning the
appliance. Never permit liquids to penetrate
inside the appliance. Otherwise the appliance
could be damaged.
Clean the appliance regularly, preferably imme-
diately after completion of the work.
Clean the housing with a dry cloth – do not use
petrol, solvents or cleaners which can attack the
plastic.
A vacuum cleaner is required for thorough
cleaning of the appliance.
Ventilation openings must never be obstructed.
Remove any sanding dust stuck to the appliance
with a brush.
NOTE
Replacement parts not listed (such as carbon
brushes, switch) can be ordered via our
service hotline.
WARNING!
Do not use any accessories not recom-
mended by PARKSIDE. This can lead to
electric shock and fire.
Disposal
The packaging consists of environ-
mentally friendly material. It can be
disposed of in the local recycling
containers.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU
requires that worn-out power tools be
collected separately and recycled in an environ-
mentally compatible manner.
Do not dispose of batteries in
your normal household waste!
Remove the batteries from the appli-
ance before disposal. Defective or
worn-out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Take the battery pack and/or appliance to a
nearby collection facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Dispose of the packaging in an envi-
ronmentally friendly manner.
Note the labelling on the packaging
and separate the packaging material
components for disposal if necessary. The pack-
aging material is labelled with abbreviations (b)
and numbers (a) with the following meanings:
1–7: plastics, 20–22: paper and cardboard,
80–98: composites
Your local community or municipal
authorities can provide information
on how to dispose of the worn-out
product.
PWSA 20-Li C3 GBCY 15
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The warranty period starts on the date of purchase.
Please keep your receipt in a safe place. This will
be required as proof of purchase.
If any material or manufacturing fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
or refund the purchase price (at our discretion).
This warranty service requires that you present the
defective appliance and the proof of purchase
(receipt) within the three-year warranty period,
along with a brief written description of the fault
and of when it occurred.
If the defect is covered by the warranty, your
product will either be repaired or replaced by us.
The repair or replacement of a product does not
signify the beginning of a new warranty period.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accord-
ance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or to fragile
parts which could be considered as consumable
parts such as switches or parts made of glass.
The warranty does not apply if the product has
been damaged, improperly used or improperly
maintained. The directions in the operating instruc-
tions for the product regarding proper use of the
product are to be strictly followed. Uses and
actions that are discouraged in the operating
instructions or which are warned against must be
avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall
be deemed void in cases of misuse or improper
handling, use of force and modifications / repairs
which have not been carried out by one of our
authorised Service centres.
The warranty period does not apply to
Normal reduction of the battery capacity
over time
Commercial use of the product
Damage to or alteration of the product by the
customer
Non-compliance with safety and maintenance
instructions, operating errors
Damage caused by natural hazards
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140

Parkside PWSA 20-Li C3 Instrucțiuni de utilizare

Categorie
Unelte electrice
Tip
Instrucțiuni de utilizare