Parkside PAMFW 20-LI A1 Translation Of The Original Instructions

AKKU-MULTIFUNKTIONS-

WERKZEUG

Originalbetriebsanleitung

IAN 339108_1910

CORDLESS MULTI-PURPOSE TOOL

Translation of the original instructions

АКУМУЛАТОРЕН МНОГОФУНК-

ЦИОНАЛЕН ИНСТРУМЕНТ

Превод на оригиналното ръководство за експлоатация

UNEALTĂ MULTIFUNCŢIONALĂ

CUACUMULATOR

Traducerea instrucţiunilor de utilizare original

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ

ΠΟΛΥΕΡΓΑΛΕΙΟ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

AKU VIŠENAMJENSKI ALAT

Prijevod originalnih uputa za uporabu

AKU VIŠENAMENSKI ALAT

Prevod originalnog uputstva za upotrebu

CORDLESS MULTI-PURPOSE TOOL PAMFW 20-Li A1

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 15

RS Prevod originalnog uputstva za upotrebu Strana 29

RO Traducerea instrucţiunilor de utilizare original Pagina 43

BG Превод на оригиналното ръководство за експлоатация Cтраница 57

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 73

DE / AT / CH Originalbetriebsanleitung Seite 89

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

654

Z52 A1

Z64 B2

HCS

C

A

20V max.

18V

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3/PDSLG 20 A1 of the

X20V Team series are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger PLG 20 A1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

60 min

2,4 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

35 min

3,5 A

45 min

4,5 A

60 min

4,5 A

max. 4.5 A

Charger PDSLG 20 A1

35 min

3,5 A

45 min

4,5 A

60 min

4,5 A

PAMFW 20-Li A1

GB

│

CY

│

1 ■

Contents

Introduction .........................................................2

Intended use .................................................................... 2

Features ........................................................................ 2

Package contents ................................................................. 2

Technical data ................................................................... 2

General power tool safety warnings .....................................3

1. Work area safety .............................................................. 3

2. Electrical safety ................................................................ 4

3. Personal safety ................................................................ 4

4. Power tool use and care ......................................................... 5

5. Battery tool use and care ........................................................ 5

6. Service ....................................................................... 6

Appliance-speciﬁc safety instructions for grinders ........................................ 6

Safety guidelines for battery chargers ................................................. 6

Working procedures .............................................................. 7

Before use ...........................................................7

Attaching/disconnecting the battery pack to/from the appliance ........................... 7

Checking the battery charge level .................................................... 7

Charging the battery pack (seeﬁg.A) ................................................ 7

Dust/chip extraction .............................................................. 8

Connecting a dust extraction unit .................................................... 8

Selecting a tool .................................................................. 8

Fitting the sanding sheet onto the sanding plate ......................................... 9

Changing tools .................................................................. 9

Use ................................................................10

Switching on and oﬀ .............................................................10

Selecting oscillation speed ........................................................10

Maintenance and cleaning ............................................10

Kompernass Handels GmbH warranty ..................................11

Service .............................................................12

Importer ...........................................................12

Disposal ............................................................12

Translation of the original Conformity Declaration .........................13

Ordering a replacement battery ........................................14

Telephone ordering ..............................................................14

IB_339108_PAMFW20-LiA1_LB7.indb 1 09.03.20 11:50

PAMFW 20-Li A1

■ 2

│

GB

│

CY

CORDLESS MULTI-PURPOSE

TOOL PAMFW 20-Li A1

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

The appliance is intended for sawing, cutting and

grinding. The following materials are preferable for

processing: wood, plastic, drywall elements, light

and non-ferrous metals, fasteners (e.g. nails, screws)

and wall tiles. It is particularly suitable for near-edge

and ﬂush work. Any other usage or modiﬁcation of

the appliance is considered improper and carries a

signiﬁcant risk of accidents. Not for commercial use.

Features

Tool release lever

ON/OFF switch

Release button for battery pack

Battery pack*

Battery charge level button

Battery display LED

Speed adjustment wheel

LED work light

Tensioning screw

Dust extraction unit (2 pcs.)

Angle adapter

Scraper 52 mm

Diamond saw blade 65 mm

HCS plunge saw blade 32 mm

Sanding plate

High-speed charger*

Red charge control LED

Green charge control LED

Sanding sheets

Package contents

1 cordless multi-purpose tool PAMFW 20-Li A1

1 delta sanding plate

6 sanding sheets 80 mm ﬂange

1 scraper 52 mm

1 HCS plunge saw blade 32 mm

1 diamond saw blade 65 mm

1 dust extraction unit (2 pcs.)

1 carrying case

1 set of operating instructions

Technical data

Cordless multi-purpose tool PAMFW 20-Li A1

Rated voltage 20 V (DC)

Rated idle speed n

0

5000–19000 rpm

Oscillation angle 3.2°

Rechargeable battery PAP 20 A1*

Type LITHIUM ION

Rated voltage 20 V

(DC)

Capacity 2 Ah

Cells 5

High-speed battery charger PLG 20 A1*

INPUT

Rated voltage 230–240 V ∼, 50 Hz

(AC)

Rated power

consumption 65 W

Fuse (internal) 3.15 A

T3.15A

OUTPUT

Rated voltage 21.5 V (DC)

Rated current 2.4 A

Charging time approx. 60 min

Protection class II /

(double insulation)

* BATTERY AND CHARGER ARE NOT INCLUDED

IB_339108_PAMFW20-LiA1_LB7.indb 2 09.03.20 11:50

PAMFW 20-Li A1

GB

│

CY

│

3 ■

Noise and vibration data

Noise measurement value determined in accord-

ance with EN 62841. The A-rated noise level of

the power tool is typically as follows:

Noise emission values

Sound pressure level L

pA

= 78 dB (A)

Uncertainty K

pA

= 3 dB

Sound power level L

WA

= 89 dB (A)

Uncertainty K

WA

= 3 dB

Wear hearing protection!

Total vibration value (vector total of three

directions) determined in accordance with

EN62841:

Sanding

Vibration emission value a

h

= 9.1 m/s

2

Uncertainty K = 1.5 m/s

2

NOTE

► The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with a

standardised test procedure and can be used

for comparison of the power tool with

another tool.

► The speciﬁed total vibration values and the

noise emission values can also be used to

make a provisional load estimate.

WARNING!

► Depending on the manner in which the

power tool is being used, and in particular

the kind of workpiece that is being worked,

the vibration and noise emission values can

deviate from the values given in these

instructions during actual use of the power

tool.

► Try to keep the load as low as possible.

Measures to reduce the vibration load are,

e.g. wearing gloves and limiting the working

time. Wherein all states of operation must be

included (e.g. times when the power tool is

switched oﬀ and times where the power tool

is switched on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings, instructions,

illustrations and speciﬁcations provided

with this power tool. Failure to follow all

instructions listed below may result in electric

shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term „power tool“ in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

IB_339108_PAMFW20-LiA1_LB7.indb 3 09.03.20 11:50

PAMFW 20-Li A1

■ 4

│

GB

│

CY

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment

such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles. A careless

action can cause severe injury within a fraction

of a second.

IB_339108_PAMFW20-LiA1_LB7.indb 4 09.03.20 11:50

PAMFW 20-Li A1

GB

│

CY

│

5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detach-

able, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation. If

damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in

unexpected situations.

5. Battery tool use and care

a) Recharge only with the charger speciﬁed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

ﬁre when used with another battery pack.

b) Use power tools only with speciﬁcally

designated battery packs. Use of any other

battery packs may create a risk of injury and

ﬁre.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery

terminals together may cause burns or a ﬁre.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable behaviour

resulting in ﬁre, explosion or risk of injury.

f) Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre or

temperature above 130 °C (265°F) may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instruc-

tions. Charging improperly or at temperatures

outside the speciﬁed range may damage the

battery and increase the risk of ﬁre.

IB_339108_PAMFW20-LiA1_LB7.indb 5 09.03.20 11:50

PAMFW 20-Li A1

■ 6

│

GB

│

CY

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Protect the rechargeable battery

from heat, for example from

continuous exposure to sunlight,

ﬁre, water and moisture.

There is a risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

Appliance-speciﬁc safety instructions

for grinders

WARNING!

■ Dusts from materials such as leaded paint,

some types of wood and metal can be

harmful to your health.

■ Contact with or inhalation of these dusts can

represent a health hazard for the person

operating the appliance and other people in

the vicinity.

■ Wear safety goggles and a protective dust

mask!

Safety guidelines for battery chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited phys-

ical, sensory or mental capabilities

or lack of experience and know-

ledge, provided that they are under

supervision or have been told how

to use the appliance safely and are

aware of the potential risks. Do not

allow children to use the appliance

as a toy. Cleaning and user mainte-

nance tasks must not be carried out

by children unless they are super-

vised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for

indoor use only.

ATTENTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/PAP 20 A3

.

♦ A current list of battery compatibility can be

found at www.lidl.de/Akku.

WARNING!

■ Do not operate the appliance with a

damaged cable, power cable or power plug.

A damaged power cable poses a threat of a

fatal electric shock.

■ Do not use any accessories which are not

recommended by PARKSIDE. This can lead to

an electric shock and ﬁre.

IB_339108_PAMFW20-LiA1_LB7.indb 6 09.03.20 11:50

PAMFW 20-Li A1

GB

│

CY

│

7 ■

Working procedures

Working principle

The oscillating drive causes the application tool to

move back and forth at a speed of 5000–19000

times per minute. This allows for precision work

even in conﬁned spaces.

Sawing/cutting

■ Use only undamaged saw blades that are in

perfect working order. Bent, blunt or otherwise

damaged saw blades may break.

■ When sawing lightweight construction mate-

rials, follow the statutory regulations and all

recommendations from the material manufac-

turers.

■ Only soft materials such as wood, plasterboard

or similar should be processed using the plunge

saw process.

Sanding

■ To prolong the service life of the sanding

sheets

, ensure that you apply even pressure.

Before use

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack

♦ Push the battery pack

into the handle until it

clicks into place.

Removing the battery pack

♦ Press the release button

and remove the

battery pack .

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram).

The status/remaining charge will be shown on

the battery display LED as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Charging the battery pack

(seeﬁg.A)

CAUTION!

► Always unplug the appliance before you

remove the battery pack from or connect the

battery pack to the charger.

NOTE

► Never charge the battery pack if the ambient

temperature is below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level

is between 50% and 80%. The storage climate

should be cool and dry and the ambient

temperature should be between 0°C and

50°C.

♦ Connect the battery pack

to the high-speed

battery charger (see Fig. A).

♦ Insert the power plug into the socket.

The control LED

lights up red.

♦ The green LED

indicates that the charging

process is complete and the battery pack is

ready.

CAUTION!

♦ If the red control LED

ﬂashes, this means

that the battery pack has overheated and

cannot be charged.

♦ If the red and green control LEDs both

ﬂash, this means that the battery pack is

defective.

WARNING! RISK OF INJURY!

■ Always remove the battery before working on

the power tool.

♦ Push the battery pack

into the appliance.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

IB_339108_PAMFW20-LiA1_LB7.indb 7 09.03.20 11:50

PAMFW 20-Li A1

■ 8

│

GB

│

CY

Dust/chip extraction

Materials containing asbestos must not be

processed. Asbestos is a known carcinogen.

WARNING! RISK OF FIRE!

■ When working with electrical appliances

which can be connected to a vacuum cleaner

via a vacuum cleaner adapter, there is a risk

of ﬁre! In unfavourable conditions, e.g. when

sparks are ﬂying while sanding metal or

metal residues in wood, wood dust in the bag

of the vacuum cleaner can spontaneously

ignite. This is a particular risk if the wood dust

is mixed with paint residues or other

chemicals and the workpiece has become hot

after being worked for a long time. Therefore,

avoid overheating of the material being

sanded as well as the appliance. Always

empty the vacuum cleaner’s dust bag before

taking work breaks.

■ Always use dust extraction.

■ Ensure that your workplace is adequately

ventilated.

■ Observe the regulations applicable in your

country regarding the materials to be worked.

Connecting a dust extraction unit

♦ Place the dust extraction unit under the

appliance and ﬁx it into place on the appliance

with the screw.

♦ Fit the angle adapter

onto the dust extraction

unit .

The angle adapter can be turned by up to

180°.

Selecting a tool

NOTE

► The universal ﬁtting with its easy tool change

function is suitable for standard accessories.

HC

S

HCS plunge saw blade 32 mm

Materials

wood, plastic, gypsum (plaster) and other soft

materials

Application

– separation and plunge saw cuts

– sawing close to edges, even in hard-to-reach

areas

Example sawing recesses in lightweight walls.

Diamond saw blade

Materials

Tile adhesives, tile joints

IB_339108_PAMFW20-LiA1_LB7.indb 8 09.03.20 11:50

PAMFW 20-Li A1

GB

│

CY

│

9 ■

Application

– removing material residues, such as tile

adhesive, when replacing damaged tiles

– milling grout on wall and ﬂoor tiles.

Scraper

Materials

mortar/concrete residues, tile/carpet glue, paint/

silicone residues

Application

– removing material residues, such as carpet glue

residue on the ﬂoor.

Sanding plate

Materials

Wood and metal (sanding sheets

supplied),

wood*, metal*

* Depending on the sanding sheet

Application

– sanding up to edges and hard-to-reach areas.

Fitting the sanding sheet onto the

sanding plate

♦ Place the sanding sheet centrally on the

sanding plate

.

Changing tools

NOTE

► If you plan to use the dust extraction unit, it

must be connected before ﬁtting or changing

the tool (see. section "Connecting a dust

extraction unit").

WARNING! RISK OF INJURY!

■ Always remove the battery before working on

the power tool.

♦ If necessary, remove an already ﬁtted tool.

To do this, raise the tool release lever

.

♦ Fit the tool (e.g. the plunge saw blade

) onto

the tool holder.

NOTE

► You can ﬁt the tools in any snap position on

the tool holder.

♦ Lock the tool into place by pushing the tool

release lever

back down again.

■ Check that the tool is ﬁtted ﬁrmly. Incorrectly

or insecurely ﬁtted tools can come loose during

use and cause you an injury.

IB_339108_PAMFW20-LiA1_LB7.indb 9 09.03.20 11:50

PAMFW 20-Li A1

■ 10

│

GB

│

CY

Use

Switching on and oﬀ

Switching on

♦ Push the ON/OFF switch

forwards to switch

the appliance on.

The LED work light

lights up when the

appliance is switched on to light up the working

area in low light conditions.

NOTE

► The LED work light

can only be used when

the dust extraction unit is not ﬁtted.

Switching oﬀ

♦ Push the ON/OFF switch

backwards to

switch the appliance oﬀ.

Selecting oscillation speed

♦ Use the speed adjustment wheel to set the

required oscillation speed.

Level 1: low speed

Level 6: high speed

NOTE

► The required speed depends on the material

being worked and on the working conditions

and can be determined through practical tests.

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

■ Do not use any sharp objects to clean the

appliance. Do not allow any liquids to get into

the appliance. This can damage the appliance.

■ Clean the appliance regularly, preferably

immediately after completion of the work.

■ Use a soft, dry cloth to clean the housing.

Never use petrol, solvents or cleansers which

can damage plastic.

■ A vacuum cleaner is required for thorough

cleaning of the appliance.

■ Ventilation openings must never be obstructed.

■ Remove any sanding dust stuck to the appliance

with a brush.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

NOTE

► Replacement parts not listed (such as carbon

brushes, switches and replacement batteries)

can be ordered via our service hotline.

IB_339108_PAMFW20-LiA1_LB7.indb 10 09.03.20 11:50

PAMFW 20-Li A1

GB

│

CY

│

11 ■

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from the

date of purchase. If this product has any faults, you,

the buyer, have certain statutory rights. Your statu-

tory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating

instructions for the product regarding proper use of

the product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper

handling, use of force and modiﬁcations/repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and information

about what the defect is and when it occurred.

IB_339108_PAMFW20-LiA1_LB7.indb 11 09.03.20 11:50

PAMFW 20-Li A1

■ 12

│

GB

│

CY

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to

the Lidl service page (www.lidl-service.com) where

you can open your operating instructions by

entering the item number (IAN) 123456.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 339108_1910

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Disposal

The packaging is made from environ-

mentally friendly material and can be

disposed of at your local recycling plant.

Do not dispose of power tools

in your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in an environ-

mentally compatible manner.

Do not dispose of batteries in

your normal household waste!

Defective or worn-out rechargeable

batteries must be recycled according

to Directive 2006/66/EC. Take the battery pack

and/or appliance to a nearby collection facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The pack-

aging material is labelled with abbreviations (a)

and numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

The product is recyclable, subject to

extended producer responsibility and

is collected separately.

IB_339108_PAMFW20-LiA1_LB7.indb 12 09.03.20 11:50

PAMFW 20-Li A1

GB

│

CY

│

13 ■

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the

declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament

and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic

appliances.

Applied harmonised standards:

EN 62841-1:2015

EN 62841-2-4:2014

EN 55014-1:2017

EN 55014-2:2015

EN 61000-3-3:2013

EN 61000-3-2:2014

EN 62233:2008

EN 50581: 2012

Type/appliance designation: Cordless multi-purpose tool PAMFW 20-Li A1

Year of manufacture: 01–2020

Serial number: IAN 339108_1910

Bochum, 23/01/2020

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

IB_339108_PAMFW20-LiA1_LB7.indb 13 09.03.20 11:50

PAMFW 20-Li A1

■ 14

│

GB

│

CY

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the Internet on

www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

► Online ordering of replacement parts might not be possible in some countries. In this is the case,

please contact the Service hotline.

Telephone ordering

Service Great Britain Tel.: 0800 404 7657

CY

Service Cyprus Tel.: 8009 4409

To ensure fast processing of your order, have the article number of your appliance to hand

(e.g. IAN 339108) in case of questions. The article number can be found on the type plate

or the title page of these instructions.

IB_339108_PAMFW20-LiA1_LB7.indb 14 09.03.20 11:50

PAMFW 20-Li A1

HR

│

15 ■

Sadržaj

Uvod ..............................................................16

Namjenska uporaba .............................................................16

Oprema .......................................................................16

Opseg isporuke .................................................................16

Tehnički podaci .................................................................16

Opće sigurnosne napomene za uporabu električnog alata ..................17

1. Sigurnost na radnom mjestu .....................................................17

2. Električna sigurnost ............................................................18

3. Sigurnost osoba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4. Korištenje i rukovanje električnim alatom ............................................19

5. Korištenje i rukovanje baterijskim alatom ............................................19

6. Servis .......................................................................20

Sigurnosne napomene speciﬁčne zabrusilice ..........................................20

Sigurnosne napomene za punjače ..................................................20

Napomene za rad ...............................................................21

Prije uključivanja uređaja .............................................21

Umetanje paketa baterija u uređaj/vađenje ...........................................21

Provjera stanja baterije ...........................................................21

Punjenje paketa baterije (vidislikuA) ................................................21

Usisavanje prašine/strugotina ......................................................22

Priključivanje usisivača prašine .....................................................22

Odabir alata za rad .............................................................22

Postavljanje brusnog lista na brusnu ploču ............................................23

Zamjena alata za rad ............................................................23

Puštanje u rad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Uključivanje/Isključivanje. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Predodabir broja vibracija .........................................................24

Održavanje i čišćenje .................................................24

Jamstvo tvrtke Kompernass Handels GmbH ..............................25

Servis ..............................................................26

Uvoznik ............................................................26

Zbrinjavanje ........................................................26

Prijevod originalne izjave o sukladnosti .................................27

Narudžba zamjenske baterije .........................................28

Telefonska narudžba .............................................................28

IB_339108_PAMFW20-LiA1_LB7.indb 15 09.03.20 11:50

PAMFW 20-Li A1

■ 16

│

HR

AKU VIŠENAMJENSKI ALAT

PAMFW 20-Li A1

Uvod

Čestitamo na kupnji Vašeg novog uređaja. Time

ste se odlučili za vrlo kvalitetan proizvod. Upute za

uporabu sastavni su dio ovog proizvoda. One

sadrže važne napomene za sigurnost, rukovanje i

zbrinjavanje. Prije uporabe proizvoda upoznajte se

sa svim napomenama za rukovanje i sa svim sigur-

nosnim napomenama. Proizvod koristite isključivo

na opisani način i u navedenim područjima upora-

be. U slučaju predaje proizvoda trećim osobama,

priložite i također predajte i svu dokumentaciju.

Namjenska uporaba

Uređaj je namijenjen za piljenje, razdvajanje

i brušenje. U prvom redu se mogu obrađivati slje-

deći materijali: Drvo, plastika, suhi građevinski

elementi, laki i obojeni metali, elementi za pričvršći-

vanje (npr. čavli i vijci) i zidne pločice. Alat je po-

sebno prikladan za radove blizu rubova i radove

na poravnatim elementima. Svaki drugi način upo-

rabe i svaka izmjena uređaja smatra se nenamjen-

skom i krije znatnu opasnost od nezgode. Uređaj

nije namijenjen za uporabu u gospodarske svrhe.

Oprema

Poluga za deblokadu alata

Prekidač UKLJ/ISKLJ

Tipka za deblokadu paketa baterija

Paket baterija*

Tipka za stanje baterije

LED indikator baterije

Kotačić za odabir broja vibracija

LED radna svjetiljka

Stezni vijak

Usisivač prašine (2-djelni)

Kutni adapter

Strugač 52 mm

Dijamantna ploča za rezanje 65 mm

HCS ubodni rezni list 32 mm

Brusna ploča

Brzi punjač*

Crvena LED svjetiljka za kontrolu punjenja

Zelena LED svjetiljka za kontrolu punjenja

Brusni listovi

Opseg isporuke

1 Aku višenamjenski alat PAMFW 20-Li A1

1 Brzi punjač baterija PLG 20 A1

1 Paket baterija PAP 20 A1

1 Delta brusna ploča

6 Brusni listovi veličine 80 mm

1 Nož za struganje 52 mm

1 HCS ploča za rezanje s uranjanjem 32 mm

1 Dijamantna ploča za rezanje 65 mm

1 Usisivač prašine (2-djelni)

1 Kofer za nošenje

1 Upute za uporabu

Tehnički podaci

Aku višenamjenski alat PAMFW 20-Li A1

Nazivni napon 20 V

(istosmjerna struja)

Nazivni broj okretaja

u praznom hodu n

0

5000 –19000 min

-1

Kut oscilacije 3,2°

Paket baterija PAP 20 A1*

Tip LITIJ-IONSKA

Nazivni napon 20 V

(istosmjerna struja)

Kapacitet 2 Ah

Broj ćelija 5

Brzi punjač baterija PLG 20 A1*

ULAZ/Input

Nazivni napon 230 – 240 V ∼, 50 Hz

(izmjenična struja)

Nazivna snaga 65 W

Osigurač (unutarnji) 3,15 A

T3.15A

IB_339108_PAMFW20-LiA1_LB7.indb 16 09.03.20 11:50

Pagina se încarcă ...

Parkside PAMFW 20-LI A1 Translation Of The Original Instructions

Acest manual este potrivit și pentru

Parkside PAMFW 20-LI A1 Translation Of The Original Instructions

Lucrări conexe

Alte documente