RIDGID micro CD-100 Manual de utilizare

p. 1

p. 13

p. 25

p. 37

p. 49

p. 63

p. 77

p. 89

p. 101

p. 113

p. 125

p. 137

p. 149

p. 161

p. 173

p. 185

p. 197

p. 209

p. 221

p. 233

p. 245

p. 259

EN

FR

ES

DE

NL

IT

PT

SV

DA

NO

FI

PL

CZ

SK

RO

HU

EL

HR

SL

SR

RU

TR

micro

CD-100

Tools For The Professi

o

TM

RIDGE TOOL COMPANY

micro CD-100

Combustible Gas Detector

micro CD-100 Combustible Gas Detector

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

micro CD-100

WARNING

Read this operator’s manual

carefully before using this tool.

Failure to understand and fol-

low the contents of this manual

may result in electrical shock,

fire and/or serious personal in-

jury.

micro CD-100 Combustible Gas Detector

Ridge Tool Company

2

Troubleshooting .....................................................................11

Lifetime Warranty ....................................................Back Cover

*Original Instructions

Table of Contents

Recording Form for Machine Serial Number .........................1

Safety Symbols.........................................................................3

General Safety Rules

Work Area Safety ...................................................................3

Electrical Safety......................................................................3

Personal Safety ......................................................................4

Equipment Use and Care .......................................................4

Service....................................................................................4

Specific Safety Information

Combustible Gas Detector Safety ..........................................4

Description, Specifications And Standard Equipment

Description..............................................................................5

Specifications .........................................................................5

Controls ..................................................................................7

LED Display ...........................................................................7

Standard Equipment...............................................................7

Changing/Installing Batteries..................................................8

Pre-Operation Inspection ........................................................8

Set-Up and Operation ..............................................................9

Maintenance

Cleaning ...............................................................................10

Sensor Calibration/Replacement..........................................10

Storage....................................................................................10

Service and Repair .................................................................11

Disposal...................................................................................11

Battery Disposal .....................................................................11

micro CD-100 Combustible Gas Detector

Ridge Tool Company

3

• Do not operate equipment in explosive atmospheres, such

as in the presence of flammable liquids, gases or dust.

Equipment can create sparks which may ignite the dust or fumes

• Keep children and by-standers away while operating equip-

ment. Distractions can cause you to lose control.

Electrical Safety

• Avoid body contact with earthed or grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is an in-

creased risk of electrical shock if your body is earthed or

grounded.

• Do not expose equipment to rain or wet conditions. Water

entering equipment will increase the risk of electrical shock.

General Safety Rules

WARNING

Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, fire

and/or serious injury.

SAVE THESE INSTRUCTIONS!

The CE declaration of conformity (890-011-320) will accompany

this manual as a separate booklet when required.

Work Area Safety

• Keep your work area clean and well lit. Cluttered or dark areas

invite accidents.

Safety Symbols

In this operatorʼs manual and on the product, safety symbols and signal words are used to communicate important safety information. This

section is provided to improve understanding of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE indicates information that relates to the protection of property.

This symbol means read the operatorʼs manual carefully before using the equipment. The operatorʼs manual contains important

information on the safe and proper operation of the equipment.

NOTICE

DANGER

WARNING

CAUTION

micro CD-100 Combustible Gas Detector

Ridge Tool Company

4

Personal Safety

• Stay alert, watch what you are doing and use common

sense when operating equipment. Do not use equipment

while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating equip-

ment may result in serious personal injury.

• Use personal protective equipment. Always wear eye protec-

tion. Protective equipment such as dust mask, non-skid safety

shoes, hard hat or hearing protection used for appropriate con-

ditions will reduce personal injuries.

• Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in unex-

pected situations.

Equipment Use and Care

• Do not force equipment. Use the correct equipment for your

application. The correct equipment will do the job better and

safer at the rate for which it is designed.

• Do not use equipment if the switch does not turn it ON and

OFF. Any tool that cannot be controlled with the switch is danger-

ous and must be repaired.

• Disconnect the batteries from the equipment before making

any adjustments, changing accessories or storing. Such pre-

ventive safety measures reduce the risk of injury.

• Store idle equipment out of the reach of children and do not

allow persons unfamiliar with the equipment or these in-

structions to operate the equipment. Equipment can be dan-

gerous in the hands of untrained users.

• Maintain equipment. Check for misalignment or binding of mov-

ing parts, missing parts, breakage of parts and any other condi-

tion that may affect the equipmentʼs operation. If damaged, have

the equipment repaired before use. Many accidents are caused

by poorly maintained equipment

• Use the equipment and accessories in accordance with

these instructions, taking into account the working condi-

tions and the work to be performed. Use of the equipment for

operations different from those intended could result in a haz-

ardous situation.

• Use only accessories that are recommended by the manu-

facturer for your equipment. Accessories that may be suitable

for one piece of equipment may become hazardous when used

with other equipment.

• Keep handles dry and clean; free from oil and grease. Allows

for better control of the equipment.

Service

• Have your equipment serviced by a qualified repair person

using only identical replacement parts. This will ensure that

the safety of the tool is maintained.

Specific Safety Information

WARNING

This section contains important safety information that is

specific to this tool.

Read these precautions carefully before using the micro CD-

100 Combustible Gas Detector to reduce the risk of fire, ex-

plosion or other serious personal injury.

SAVE THESE INSTRUCTIONS!

Keep this manual with the tool for use by the operator.

Combustible Gas Detector Safety

• High concentrations of combustible gases can cause ex-

plosions, fires, asphyxia and other hazards that could

micro CD-100 Combustible Gas Detector

Ridge Tool Company

5

of measurement within two (Low and High) settings of sensitivity.

When the tool senses the presence of a combustible gas, it will tell

the operator by blinking the appropriate light(s), triggering the ap-

propriate audible alert or providing the appropriate vibration alert.

The micro CD-100 comes equipped with an attached flexible 40 cm

probe hose.

Specifications

Visual Alert....................................5 Red LEDs: Gas Measuring

Levels; Sensitivity Visual Alert

Audible Alert(85 db) ......................Loud Audible Ticking Rate

(w/Continuous Modulation

Proportional to Gas Level)

Vibration Alert ...............................Standard

Sensitivity .......................................40 ppm (methane)

Response Time ..............................< 2 Seconds

Range.............................................0 – 6400 ppm (methane)

Sensitivity Level

(methane) (HIGH) .........................5 Levels:

40/80/160/320/640 ppm

Sensitivity Level

(methane) (LOW)..........................5 Levels:

400/800/1600/3200/6400 ppm

Warm Up Calibration ....................Automatic

Warm Up Time..............................50 Seconds Max

Operating Buttons.........................Five: Power ON/OFF, High

Sensitivity, Low Sensitivity,

Audio Alerts, Vibration Alerts

Batteries .......................................4 x “AA”

Low Battery Status .......................Low and High Sensitivity LED

Solid

Sensor Connection .......................Plug-In

cause serious personal injury or death. Know the character-

istics of the gas you are working with and use proper precau-

tions to avoid hazardous conditions.

• Always turn on and calibrate the gas detector in an area

known to be free of combustible gases. Calibration in an

area containing combustible gas will result in incorrect calibra-

tion and lower than actual readings. This could result in com-

bustible gases not being detected.

If you have any question concerning this RIDGID product:

• Contact your local RIDGID distributor.

• Visit www.RIDGID.com or www.RIDGID.eu to find your local

RIDGID contact point.

• Contact RIDGID Technical Services Department at rtctechser-

vices@emerson.com, or in the U.S. and Canada call (800) 519-

3456.

Description, Specifications

And Standard Equipment

Description

The RIDGID

®

micro CD-100 Combustible Gas Detector is a gas leak

locating tool that is used to identify the presence of and isolate the

source location of combustible gases such as methane, propane,

butane, ammonia, carbon monoxide and many others (please see

back of manual for a more complete list). Even low levels of com-

bustible gas can be detected in seconds.

The micro CD-100 detects gas concentrations through the use of

an internal sensor. This sensor is heated during operation. As the

heated sensor interacts with gases, the unit immediately indicates

to the user that combustible gases are present. The micro CD-100

indicates the presence of combustible gases with visual, audio and

vibration feedback mechanisms. There are five (5) threshold levels

micro CD-100 Combustible Gas Detector

Ridge Tool Company

6

Expected Sensor Life.....................5 Years

Probe ............................................Flexible 40 cm

Weight...........................................16 oz/450 grams

Measurable Gases

* Natural Gas typically consists of a high percentage of methane and smaller

percentages of propane and other gases.

Figure 1 – RIDGID micro CD-100 Combustible Gas Detector

Gases Detected Common Mixtures That Would Include

or Emit More Than One Of These Gases

Methane

Hydrogen Natural Gas*

Carbon Monoxide

Propane

Ethylene Paint Thinners

Ethane

Hexane

Benzene Industrial Solvents

Iso-Butane

Ethanol

Acetaldehyde Dry Cleaning Fluids

Formaldehyde

Toluene

P-Xylene Gasoline

Ammonia

Hydrogen Sulfide

Features

• 40 cm Adjustable Probe

• Replaceable Sensor

• TRI Mode Detection

micro CD-100 Combustible Gas Detector

Ridge Tool Company

7

Standard Equipment

• micro CD-100

• Batteries 4 x AA

Low Sensitivity

Indicator

LED Display

High

Sensitivity

Indicator

Warm Up

Indicator

Figure 3 – micro CD-100 Display

Display

• Replaceable Gas Sensor

• Operator's Manual

Low Sensitivity

Selector

Power

ON/OFF

Vibration Alert

Enable/Disable

Audible

Alert

Enable/Disable

High Sensitivity

Selector

Figure 2 – micro CD-100 Parts

Controls

Display

micro CD-100 Combustible Gas Detector

Ridge Tool Company

8

Figure 4 – Removing Battery Compartment Cover

Changing/Installing Batteries

The micro CD-100 comes without the batteries installed. If the high

sensitivity (yellow) and low sensitivity (white) lights are ON at the

same time, this indicates that the batteries need to be replaced.

Remove the batteries prior to long term storage or shipment to pre-

vent battery leakage. Never change batteries in the presence of

combustible gases to reduce the risk of explosions, fires and other

serious injury.

1. Depress the battery compartment cover catch (See Figure 4)

and remove the cover. If needed, remove batteries.

2. Install four AA alkaline batteries (LR6), observing correct po-

larity as indicated in the battery compartment.

3. Replace the battery compartment cover. Confirm securely at-

tached.

4. Confirm battery cover clasp is locked. (Figure 5)

Figure 5 – Battery Cover Clasp

Pre-Operation Inspection

WARNING

Before each use, inspect your micro CD-100 and correct any

problems to reduce the risk of injury or incorrect measure-

ments.

1. Clean any oil, grease or dirt from equipment. This aids inspec-

tion.

2. Inspect the micro CD-100 for any broken, worn, missing, mis-

aligned or binding parts, or any other condition which may pre-

vent safe and normal operation.

3. Check that the warning labels are present, firmly attached and

readable. (See Figure 6.)

4. If any issues are found during the inspection, do not use the

micro CD-100 until it has been properly serviced.

micro CD-100 Combustible Gas Detector

Ridge Tool Company

9

and lower than actual readings. This could result in com-

bustible gases not being detected.

Set up and Operate the gas detector according to these proce-

dures to reduce the risk of fire, explosions and serious injury

and incorrect measurements.

1. Check for an appropriate work area as indicated in the General

Safety Section.

2. Determine the application and confirm that you have the cor-

rect equipment. See the Specifications section for information

on sensitivity, gases detected and other information.

3. Make sure that all equipment has been properly inspected.

4. In an area where combustible gases are known to not be pres-

ent, turn on the gas detector by pressing and releasing the

ON/OFF button. For one second the gas detector will vibrate,

beep, and the first level red light will come on to indicate that

the unit is ON. The gas detector then starts an approximately

50 second sensor heat up and calibration, during which the

first level red light is blinking.

Once the calibration is complete, for one second, all level lights

will flash, and if the audible and vibration alerts are ON, the unit

will beep and vibrate. Then either the high (yellow) or low

(white) light will be ON. If the high (yellow) and low (white) sen-

sitivity lights are ON at the same time, this indicates that the

batteries need to be replaced. If all display lights are ON, this

indicates that the sensor has failed and that the unit needs to

be serviced.

If the gas detector is left ON for more than five minutes with no

activity, it will automatically shut OFF to conserve the batter-

ies.

5. The Audible Alert and Vibration Alert retain the previous state

the detector was last in and can be turned ON or OFF if de-

sired. Press and release the Audible Alert button to turn it ON

5. Following the Set-Up and Operation instructions, turn ON and

calibrate the gas detector. Once calibration is complete use a

combustible gas source (such as an unlit lighter), to confirm

that the gas detector senses the gas. If the gas detector does

not sense the gas, do not use the unit until it has been properly

serviced. Remove the gas source and allow several minutes

for the sensor to stabilize prior to use.

Figure 6 – Warning Labels

Set-Up and Operation

WARNING

High concentrations of combustible gases can cause explo-

sions, fires, asphyxia and other hazards that could cause se-

rious personal injury or death. Know the characteristics of the

gas you are working with and use proper precautions to avoid

hazardous conditions.

Always turn on and calibrate the gas detector in an area

known to be free of combustible gases. Calibration in an area

containing combustible gas will result in incorrect calibration

micro CD-100 Combustible Gas Detector

Ridge Tool Company

10

If locating a leak, use the gas detector to find areas of lower

gas concentration and follow back to the source. In a piping

system, trace the system, stopping at the joints to monitor the

gas levels.

7. When gas detection is complete, turn the micro CD-100 OFF

by pressing the ON/OFF button.

Maintenance

Cleaning

Do not immerse the micro CD-100 in water. Wipe off dirt with a

damp soft cloth. Do not use aggressive cleaning agents or solu-

tions. Treat the instrument as you would a telescope or camera.

Sensor Calibration/Replacement

The micro CD-100 requires no calibration other than that done at

regular start up. If the sensor should fail, the sensor (Catalog Part

#31948) can be replaced by a RIDGID Independent Authorized

Service Center.

Storage

The RIDGID micro CD-100 Combustible Gas Detector must be

stored in a dry secure area between -10°C (14°F) and 60°C

(158°F).

Store the tool in a locked area out of the reach of children and peo-

ple unfamiliar with the micro CD-100.

Remove the batteries before any long period of storage or shipping

to avoid battery leakage.

and OFF. The gas detector will beep once when the Audible

Alert is turned ON and OFF. Press and release the Vibration

Alert button to turn it ON and OFF. The gas detector will vibrate

twice when turning the Vibration Alert ON and vibrate once

when turning the Vibration Alert OFF.

6. Enter the area to be monitored. Pay close attention to the gas

level indicators (see Table 1). As gas levels increase, more red

level lights will come on and the frequency of the Audible Alert

beeping and the Vibration Alert vibration will increase. See

Table 1 for information on methane concentration levels and

gas detector feedback.

Table 1 – Gas Detector Feedback For Methane Concentration

Levels

* Gas Concentration levels may differ depending on the specific gas detected

When the gas detector is turned ON it is in whatever sensitiv-

ity state it was last in. In the low sensitivity setting, the lowest

concentration of methane detected is 400 ppm. Switch the sen-

sitivity to the high setting by pressing the high sensitivity button

(H). This will be indicated by the yellow light in the bottom right

of the display. In the high sensitivity setting, the gas detector is

ten times more sensitive, with the lowest concentration of

methane detected at 40 ppm. Sensitivity can be changed at

any time by pressing the High Sensitivity (H) or Low Sensitiv-

ity (L) buttons.

Low Sensitivity High Sensitivity Level Lights Audible Alert

White Light ON Yellow Light ON

L1 L2 L3 L4 L5

Beeping

< 400 ppm < 40 ppm OFF OFF OFF OFF OFF 1 cyc/sec

400…800 ppm 40…80 ppm ON OFF OFF OFF OFF 1.02 cyc/sec

800…1600 ppm 80…160 ppm ON ON OFF OFF OFF 1.2 cyc/sec

1600…3200 ppm 160…320 ppm ON ON ON OFF OFF 1.65 cyc/sec

3200…6400 ppm 320…640 ppm ON ON ON ON OFF 3.25 cyc/sec

> 6400 ppm > 640 ppm ON ON ON ON ON 6.25 cyc/sec

micro CD-100 Combustible Gas Detector

Ridge Tool Company

11

Disposal

Parts of the RIDGID micro CD-100 Combustible Gas Detector con-

tain valuable materials and can be recycled. There are companies

that specialize in recycling that may be found locally. Dispose of the

components in compliance with all applicable regulations. Contact

your local waste management authority for more information.

For EC Countries: Do not dispose of electrical equipment

with household waste!

According to the European Guideline 2002/96/EC for

Waste Electrical and Electronic Equipment and its imple-

mentation into national legislation, electrical equipment

that is no longer usable must be collected separately and disposed

of in an environmentally correct manner.

Battery Disposal

For EC countries: Defective or used batteries must be recycled ac-

cording to the guideline 2006/66/EEC.

Service and Repair

WARNING

Improper service or repair can make the RIDGID micro CD-100

Combustible Gas Detector unsafe to operate.

Service and repair of the micro CD-100 must be performed by a

RIDGID Independent Authorized Service Center.

For information on your nearest RIDGID Independent Service Cen-

ter or any service or repair questions:

• Contact your local RIDGID distributor.

• Visit www.RIDGID.com or www.RIDGID.eu to find your local

RIDGID contact point.

• Contact RIDGID Technical Services Department at rtctechser-

vices@emerson.com, or in the U.S. and Canada call (800) 519-

3456.

High (Yellow) and Low

(White) sensitivity

lights are ON at the

same time.

All display lights are

ON at the same time.

The battery is discharged (unable to heat the sen-

sor).

The sensor (or the sensor heater) is defective.

The batteries are low and need to be changed.

Shut OFF unit. Sensor or entire unit should be re-

placed.

PROBLEM POSSIBLE REASON SOLUTION

Troubleshooting

micro CD-100 Combustible Gas Detector

Ridge Tool Company

12

Détecteur de gaz combustibles

micro CD-100

Détecteur de gaz combustibles micro CD-100

Notez ci-dessous le numéro de série indiqué sur la plaque signalétique de l’instrument pour

future référence.

Nº de

série

micro CD-100

AVERTISSEMENT

Familiarisez-vous bien avec le mode

d’emploi avant d’utiliser l’appareil.

L’incompréhension ou le non-re-

spect des consignes ci-après aug-

menteraient les risques de choc

électrique, d’incendie et/ou d’acci-

dent grave.

Recyclage de lʼinstrument.....................................................24

Recyclage des piles ...............................................................24

Dépannage..............................................................................24

Garantie à vie.......................................................page de garde

* Traduction de la notice originale

Table des matières

Fiche dʼenregistrement du numéro

de série de lʼinstrument ......................................................14

Symboles de sécurité ............................................................15

Consignes générales de sécurité

Sécurité des lieux .................................................................15

Sécurité électrique................................................................15

Sécurité individuelle..............................................................16

Utilisation et entretien de lʼinstrument...................................16

Révisions ..............................................................................16

Consignes de sécurité spécifiques

Sécurité du détecteur de gaz combustibles..........................17

Description, caractéristiques techniques et

équipements standards

Description............................................................................17

Caractéristiques....................................................................17

Commandes .........................................................................19

Affichage LED ......................................................................20

Equipements standards........................................................20

Installation et remplacement des piles ................................20

Contrôle préalable..................................................................21

Préparation et utilisation .......................................................21

Entretien

Nettoyage .............................................................................23

Calibrage et remplacement du capteur ................................23

Stockage .................................................................................23

Révisions et réparations........................................................23

Détecteur de gaz combustibles micro CD-100

Ridge Tool Company

14

Détecteur de gaz combustibles micro CD-100

Ridge Tool Company

15

• Nʼutilisez pas dʼinstruments de ce type en présence de

matières explosives telles que liquides, gaz ou poussières

combustibles. Ce type dʼinstrument peut produire des étin-

celles susceptibles dʼenflammer les poussières et émanations

combustibles.

• Eloignez les enfants et les curieux lors de lʼutilisation de ce

type dʼinstrument. Les distractions risquent de vous faire per-

dre le contrôle de lʼappareil.

Sécurité électrique

• Evitez tout contact physique avec les objets reliés à la terre

tels que canalisations, radiateurs, cuisinières et réfrigéra-

teurs. Tout contact avec la terre augmenterait les risques de

choc électrique.

Consignes générales de sécurité

AVERTISSEMENT

Familiarisez-vous avec l’ensemble du mode d’emploi. Le non-

respect des consignes d’utilisation et de sécurité ci-après aug-

menterait les risques de choc électrique, d’incendie et/ou de

grave blessure corporelle.

CONSERVEZ CES INSTRUCTIONS !

Lorsque cela sera nécessaire, la déclaration de conformité CE (890-

011-320) sera jointe à ce manuel sous la forme d'un livret distinct.

Sécurité des lieux

• Assurez-vous de la propreté et du bon éclairage des lieux.

Les zones encombrées ou mal éclairées sont une invitation aux

accidents.

Symboles de sécurité

Des symboles et mots clés spécifiques, utilisés à la fois dans ce mode dʼemploi et sur lʼinstrument lui-même, servent à signaler dʼimpor-

tants risques de sécurité. Ce qui suit permettra de mieux comprendre la signification de ces mots clés et symboles.

Ce symbole sert à vous avertir aux dangers physiques potentiels. Le respect des consignes qui le suivent vous permettra dʼéviter

les risques de blessures graves ou mortelles.

Le terme DANGER signifie une situation dangereuse potentielle qui, faute dʼêtre évitée, provoquerait la mort ou de graves

blessures corporelles.

Le terme AVERTISSEMENT signifie une situation dangereuse potentielle qui, faute dʼêtre évitée, serait suscep-

tible dʼentraîner la mort ou de graves blessures corporelles.

Le terme ATTENTION signifie une situation dangereuse potentielle qui, faute dʼêtre évitée, serait susceptible dʼen-

traîner des blessures corporelles légères ou modérées.

Le terme NOTA signifie des informations concernant la protection des biens.

Ce symbole indique la nécessité de lire le manuel soigneusement avant dʼutiliser le matériel. Le mode dʼemploi renferme dʼimpor-

tantes informations concernant la sécurité dʼutilisation du matériel.

NOTA

DANGER

AVERTISSEMENT

ATTENTION

• Nʼexposez pas lʼappareil à la pluie ou aux intempéries. Toute

pénétration dʼeau à lʼintérieur dʼun appareil électrique aug-

menterait les risques de choc électrique.

Sécurité individuelle

• Soyez attentif, faites attention à ce que vous faites et faites

preuve de bon sens. Nʼutilisez pas ce type dʼappareil lorsque

vous êtes fatigués, sous lʼinfluence de drogues, de lʼalcool ou de

médicaments. Lors de lʼutilisation dʼun appareil de ce type, un

instant dʼinattention risque dʼentraîner de graves lésions cor-

porelles.

• Prévoyez les équipements de protection individuelle néces-

saires. Portez systématiquement une protection oculaire. Le port

dʼun masque à poussière, de chaussures de sécurité antidéra-

pantes, dʼun casque de chantier ou de protecteurs dʼoreilles sʼim-

pose lorsque les conditions lʼexigent.

• Ne vous mettez pas en porte-à-faux. Maintenez une bonne po-

sition de travail et un bon équilibre à tout moment. Cela vous per-

mettra de mieux contrôler lʼappareil en cas dʼimprévu.

Utilisation et entretien du matériel

• Ne forcez pas lʼappareil. Prévoyez un appareil adapté aux

travaux envisagés. Lʼappareil approprié fera le travail plus effi-

cacement et avec un plus grand niveau de sécurité lorsquʼil

tourne au régime prévu.

• Nʼutilisez pas lʼappareil si son interrupteur marche/arrêt ne

fonctionne pas correctement. Tout appareil qui ne peut pas être

contrôlé par son interrupteur est dangereux et doit être réparé.

• Retirez les piles de lʼappareil avant de le régler, de changer

ses accessoires ou de le ranger. De telles mesures préven-

tives limiteront les risques de blessure.

• Rangez tout appareil non utilisé hors de la portée des en-

fants et des individus qui nʼont pas été familiarisés avec ce

type de matériel ou son mode dʼemploi. Les appareils élec-

triques peuvent devenir dangereux sʼils tombent entre les mains

dʼutilisateurs non initiés.

• Veillez à lʼentretien de lʼappareil. Examinez-le pour signes de

désalignement, de grippage, dʼabsence ou de bris de ces com-

posants, et de toute autre anomalie qui risquerait de nuire à son

bon fonctionnement. Le cas échéant, faire réparer lʼappareil

avant de lʼutiliser. De nombreux accidents sont provoqués par

des appareils mal entretenus.

• Servez-vous de lʼappareil et de ses accessoires selon les

consignes ci-présentes en tenant compte des conditions de

travail et des travaux envisagés. Lʼutilisation de ce matériel à

des fins autres que celles prévues pourrait sʼavérer dangereux.

• Utilisez exclusivement les accessoires prévus par le fabri-

cant pour votre type dʼappareil particulier. Lʼutilisation dʼac-

cessoires adaptés à dʼautres types dʼappareil risque de sʼavérer

dangereuse.

• Assurez la parfaite propreté de lʼappareil. Cela permettra de

mieux le contrôler.

Révisions

• Confiez les révisions de ce matériel a un réparateur quali-

fié utilisant exclusivement des pièces de rechange iden-

tiques à celles dʼorigine. Cela assurera la sécurité intrinsèque

du matériel.

Consignes de sécurité spécifiques

AVERTISSEMENT

La section suivante contient d’importantes consignes de sécu-

rité qui s’adressent spécifiquement à ce type d’instrument.

Afin de limiter les risques d’incendie et de choc électrique ou

autres blessures graves, lisez le mode d’emploi soigneuse-

ment avant d’utiliser le détecteur de gaz combustibles CD100.

Détecteur de gaz combustibles micro CD-100

Ridge Tool Company

16

Détecteur de gaz combustibles micro CD-100

Ridge Tool Company

17

sulter le dos du manuel pour une liste plus exhaustive). Même de

faibles concentrations de gaz combustibles peuvent être détectées

en quelques secondes.

Le micro CD-100 fait appel à un capteur interne pour détecter les

concentrations de gaz. Ce capteur est chauffé en cours dʼopération.

Le capteur chauffé réagit au gaz et avertit instantanément lʼutilisa-

teur de la présence de gaz combustibles. Le micro CD-100 signale

la présence de gaz combustibles par le biais de mécanismes dʼaver-

tissement visuels, audio et vibratoires. Lʼappareil dispose de cinq

(5) seuils et de deux plages (haute et base) de sensibilité. Lorsque

lʼinstrument détecte la présence dʼun gaz combustible, il avertit lʼu-

tilisateur en faisant clignoter le(s) témoin(s) approprié(s) ou en dé-

clenchant lʼalarme audible ou vibratoire correspondante.

Le micro CD-100 est livré avec une sonde flexible de 40 cm de long.

Caractéristiques techniques

Alarme visuelle .............................5 LED rouges : niveaux de

concentration des gaz, alerte

visuelle de sensibilité

Alarme audible (85db) ..................LCliquetis sonore strident

(avec modulation de cadence

en fonction de la concentration

des gaz)

Alarme vibratoire ..........................Standard

Sensibilité .......................................40 ppm (méthane)

Temps de réponse..........................< 2 secondes

Plage ..............................................0 à 6400 ppm (méthane)

Niveau de sensibilité

maxi (méthane).............................5 niveaux :

40/80/160/320/640 ppm

Niveau de sensibilité

CONSERVEZ CES INSTRUCTIONS !

Gardez le présent manuel à portée de main de lʼutilisateur.

Sécurité du détecteur de gaz combustibles

• Des concentrations élevées de gaz combustibles peuvent

provoquer des explosions, des incendies, lʼasphyxie et

autres dangers susceptibles dʼoccasionner des blessures

graves ou mortelles. Familiarisez-vous avec les caractéris-

tiques du type de gaz en présence et appliquez les précautions

appropriées afin dʼéviter de tels dangers.

• Le détecteur de gaz doit toujours être activé et calibré dans

un endroit manifestement exempt de gaz combustibles. La

présence de gaz combustibles lors du calibrage du détecteur

nuirait à la précision du calibrage et produirait des lectures in-

férieures aux taux véritables, au point, éventuellement, dʼem-

pêcher lʼinstrument de détecter la présence même de gaz.

En cas de questions concernant ce produit RIDGID :

• Consultez votre distributeur RIDGID.

• Consultez les sites www.RIDGID.com ou www.RIDGID.eu pour

localiser le représentant RIDGID le plus proche.

• Consultez les services techniques de RIDGID par mail adressé

à rtctechservices@emerson.com, ou, à partir des Etats-Unis et

du Canada, en composant le (800)519-3456.

Description, caractéristiques

techniques et équipements de base

Description

Le détecteur de gaz combustibles RIDGID

®

micro CD-100 est un

détecteur de fuites de gaz qui permet de signaler la présence et lo-

caliser la source de nombreux types de gaz, notamment méthane,

propane, butane, ammoniac et monoxyde de carbone (veuillez con-

mini (méthane) .............................5 niveaux :

400/800/1600/3200/6400 ppm

Préchauffage et calibrage ............Automatiques

Durée de préchauffage ................50 secondes maxi

Touches de fonctionnement .........Cinq : Marche/Arrêt, haute

sensibilité, basse sensibilité,

alarmes audio, alarmes

vibratoires

Piles .............................................4 piles «AA»

Témoin de charge ........................LED haute et basse sensibilité

Connexion du capteur ..................Fiche

Longévité anticipée du capteur .....5 ans

Sonde...........................................Flexible de 40 cm

Poids net ......................................450 g

Gaz détectables

* Le gaz naturel est généralement composé principalement de méthane et

de plus faibles concentrations de propane et autres gaz.

Avantages principaux

• Flexible à mémoire de 40 cm

• Capteur remplaçable

• Détection 3 modes

Détecteur de gaz combustibles micro CD-100

Ridge Tool Company

18

Gaz détectés Composés courants susceptibles de retenir

ou d’émettre un ou plusieurs de ces gaz

Méthane

Azote Gaz naturel*

Monoxyde de carbone

Propane

Ethylène Diluants

Ethane

Hexane

Benzène Solvants industriels

Isobutane

Ethanol

Acétaldéhyde Produits de nettoyage à sec

Formaldéhyde

Toluène

P-xylène Essence

Ammoniaque

Sulfure dʼhydrogène

Pagina se încarcă ...

RIDGID micro CD-100 Manual de utilizare

RIDGID micro CD-100 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente