Eizo FDF2382WT Manual de utilizare

Tip
Manual de utilizare
Important
Please read this “Users Manual, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
For the latest product information including the “User’s Manual”,
refer to our web site :
www.eizoglobal.com
Touch Panel Color LCD Monitor
Users Manual
2
Location of Caution Statement
Symbols on the unit
Symbol This symbol indicates
Power button
Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
CAUTION
Refer to SAFETY SYMBOLS section in PRECAUTIONS.
WEEE marking
Product must be disposed of separately; materials may be recycled.
CE marking
EU conformity mark in accordance with the provisions of Council Directive 93/42/EEC
and 2011/65/EU.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
3
Notice for This Monitor
Notice for This Monitor
This product is suited to general purposes like creating documents, viewing multimedia content (Assuming
usage of approximately 12 hours per day).
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
Power cords provided with the product
Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
(Cautions for the Use of the Touch Panel)
During touch operation
Be careful of the following points. Otherwise, damage may occur to the monitor.
Do not strongly press, scratch, or poke the panel.
Do not touch the panel with hard objects such as ballpoint pens or metals.
4
Notice for This Monitor
Cleaning
The stains on the cabinet and LCD panel surface can be removed by using the provided cleaning cloth.
Attention
Do not allow liquid to enter the clearance between the panel and the panel frame.
Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
To Use the Monitor Comfortably
An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
5
CONTENTS
CONTENTS
Notice for This Monitor ......................................... 3
Cleaning .................................................................... 4
To Use the Monitor Comfortably ............................ 4
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ......................................................... 6
Full-at Design ................................................ 6
Easy-to-touch Stand Mechanism .................... 6
10-point Multi-touch Function ......................... 6
1-2. Controls and Functions ............................... 7
Front ................................................................ 7
Rear ................................................................. 8
1-3. Attaching the Touch Pen Holder ................. 9
1-4. EIZO LCD Utility Disk.................................... 9
Disk Contents and Software Overview ........... 9
Chapter 2 Basic Adjustment / Setting ............ 10
2-1. Enabling or Disabling the Touch Panel .....10
2-2. Switching the Input Signal ..........................10
2-3. Adjusting Brightness ..................................11
2-4. Adjusting Volume.........................................11
Chapter 3 Touch Panel Settings ..................... 12
3-1. Touch Panel Setting Method ......................12
3-2. Adjusting the Touch Position .....................12
3-3. ConguringTouchPanelOperation
Settings .........................................................14
Chapter 4 Advanced Adjustment / Setting .... 15
4-1. Basic Operation of the Setting Menu ........15
4-2. Color ..............................................................16
Color Mode .....................................................16
Brightness ......................................................16
Contrast ..........................................................17
Temperature ...................................................17
Gamma ........................................................... 17
Advanced Settings .........................................18
Color Reset ....................................................18
4-3. Screen ...........................................................19
Screen Size ....................................................19
Smoothing ......................................................19
Analog Adjustment ........................................ 20
4-4. Sound ............................................................21
Source ............................................................21
4-5. PowerManager ............................................ 22
Power Save ................................................... 22
Eco Timer ...................................................... 22
4-6. Monitor Settings ......................................... 23
Input Signal ................................................... 23
Power Indicator ............................................. 23
Languages .................................................... 23
Menu Settings ................................................24
Reset ..............................................................24
4-7. Information .................................................. 24
4-8. Locking Operation Buttons ....................... 24
Chapter 5 Troubleshooting .............................. 25
5-1. No Picture .................................................... 25
5-2. Imaging Problems
(for both digital and analog) ...................... 26
5-3. Imaging Problems (for analog only) ......... 27
5-4. Touch Panel Problems ............................... 28
5-5. Other Problems ........................................... 30
Chapter 6 Reference ........................................ 31
6-1. Attaching the Optional Arm ........................ 31
6-2. Connecting Multiple PCs ........................... 33
6-3. Specications ............................................. 34
Compatible Resolutions ................................ 35
Main Default Settings .................................... 36
Accessories ................................................... 36
Appendix .............................................................. 37
Trademark ................................................................37
License .....................................................................37
FCC Declaration of Conformity ............................ 38
LIMITED WARRANTY ............................................. 39
Recycling Information ........................................... 40
6
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
Full-atDesign
The full-at design with no steps is adopted in the bezel part. You can securely touch up to each edge
of the screen even with ngertips.
Easy-to-touch Stand Mechanism
The tilt angle can be adjusted steplessly. You can smoothly change to the easy-to-work screen
position to suit your needs such as for ofce work or multi-touch operations.
15°
70°
10-point Multi-touch Function
You can perform operations such as enlargement, reduction, and rotation using the multi-touch
function. The touch panel reacts via light touching of the screen with ngers, thereby, enabling
comfortable ick and drag operations.
Enlarge / Reduce
Rotate
7
Chapter 1 Introduction
1-2. Controls and Functions
Front
1
2
3
4
5
6
7
Setting menu
*1
1. Power indicator
Indicates the monitor’s operation status.
Blue: Screen display
Orange: Power saving mode
OFF: Main power off / Power off
2.
button
Switches the touch panel enable and disable modes, or calibrates the
touch sensitivity (page 10).
3.
button
Switches input signals for display (page 10).
4.
button
*2
Provides an item selection and function adjustment or setting option while
the Setting menu is displayed, and displays the brightness adjustment
screen (page 11).
5.
button
*2
Provides an item selection and function adjustment or setting option while
the Setting menu is displayed, and displays the volume control screen
(page 11).
6.
button
Displays the Setting menu, determines an adjustment item of each menu,
and saves values adjusted (page 15).
7.
button
Turns the power on or off.
*1 For information on how to use, see 4-1. Basic Operation of the Setting Menu” (page 15).
*2 In this User’s Manual, the
button may be hereafter simply referred as , and the button as .
8
Chapter 1 Introduction
Rear
11
12
13
8
9
10
14
15
17
18
16
8. Main power switch
Turns the main power on or off.
| : ON, ○: OFF
9. Power connector Connects the power cord.
10. Touch pen holder attachment
hole
*3
Used to attach a touch pen holder.
11. Security lock slot Complies with Kensington’s MicroSaver security system.
12. Speaker Outputs audio source.
13. Stand
(with cable holder)
Used to adjust the angle of the monitor screen.
14. Headphone jack Connects the headphones.
15. Analog voice input connector Outputs external voice from the monitor.
16. Input signal connector
Connect it to the PC.
Upper port: D-Sub mini 15-pin connector
Medium port: DVI-D connector
Lower port: DisplayPort connector
17. USB downstream port Connects a peripheral USB 2.0 device.
18. USB upstream port
Connects the USB cable for using the monitor as a touch panel monitor or
for using the USB Hub function.
*3 The touch pen holder is supplied with the touch pen (Accessories (page 36)). For the attachment method,
see “1-3. Attaching the Touch Pen Holder” (page 9).
9
Chapter 1 Introduction
1-3. Attaching the Touch Pen Holder
Note
The touch pen holder is supplied with the touch pen (Accessories (Accessories” (page 36))).
Attach the touch pen holder to any one of the right-hand and left-hand holes in the rear of the monitor. To
x the touch pen holder, use the screw supplied with the touch pen.
1-4. EIZO LCD Utility Disk
An "EIZO LCD Utility Disk" (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
Disk Contents and Software Overview
The disk includes adjustment software, touch panel software, and User’s Manual. For software
startup procedures or le access procedures, see the Readme.txt le on the disk.
Item Overview
Touch panel driver Touch panel driver supplied by EIZO.
*
1
TPOffset Software for calibrating the sensitivity of the touch panel.
*
1
Use this software when touch operations are not registered or only registered
after pressing hard.
User’s Manual of this monitor (PDF le)
Outline dimensions
Readme.txt le
*1 Only for Windows. Refer to the corresponding User’s Manual on the CD-ROM for details on installation
and use.
10
Chapter 2 Basic Adjustment / Setting
Chapter 2 Basic Adjustment / Setting
2-1. Enabling or Disabling the Touch Panel
You can switch the touch panel enable and disable modes. This function is available when you want to
temporarily display the touch panel function.
Note
Holding down allows you to calibrate the touch sensitivity.
2-2. Switching the Input Signal
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
When the signal is switched, the active input port name appears at the top right corner of the screen.
11
Chapter 2 Basic Adjustment / Setting
2-3. Adjusting Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Adjustable range
0 to 100
2-4. Adjusting Volume
You can individually tune the speaker or headphone volume.
Adjustable range
0 to 30
12
Chapter 3 Touch Panel Settings
Chapter 3 Touch Panel Settings
3-1. Touch Panel Setting Method
This product’s touch panel functions vary depending on the driver you use and its settings. Congure
settings to meet your usage applications.
Function
Windows standard
driver
Dedicated touch panel driver (DMT-DD)
*1
Driver installation Not required Required
Touch sound output x
Multi-connection
*2
r
*3
Operation mode Touch digitizer
*4
Touch digitizer
*4, 5
Mouse emulation
*5
Multi-touch operation x
*1 Included in the EIZO LCD Utility Disk (CD-ROM).
*2 √: Two or more monitors can be connected to a single computer.
*3 Only available in Windows 10.
*4 Touch operation may not be recognized on an application designed by mouse emulation.
*5 For more information about the setup procedure, see the touch panel driver’s User’s Manual (included on the
CD-ROM).
Note
When setting is completed, execute the "TPOffset" application included on the CD-ROM, and calibrate the
sensitivity of the touch panel.
When using the Windows standard driver, congure settings, referring to the following information.
3-2. Adjusting the Touch Position
Make adjustments to align the touch position with the position of the cursor displayed in response to
touching.
Attention
Do not put your hands or any metal close to the screen because the screen is susceptible to electrical conductors.
If a “User Account Control” dialog box is displayed during operation, proceed according to the displayed
instructions.
1.
Open Windows Control Panel.
The method for opening Control Panel differs depending on the operating system.
Windows 10
1. Open the Start menu, and click "All apps" - "Windows System" - "Control Panel".
Windows 8.1
1. Click
at the bottom of the "Start" screen.
The “Apps” screen appears.
2. Click “Control Panel” under “Windows System”.
Windows 7
1. Click “Start” - “Control Panel.
13
Chapter 3 Touch Panel Settings
2.
Click "Hardware and Sound" - "Tablet PC Settings".
The “Tablet PC Settings” window appears.
3.
Click "Setup" in the "Display" tab.
A touchscreen specication screen with a white background is displayed.
Attention
If using the monitor in a multiple monitor environment, specify the touchscreen according to the message
displayed on screen.
4.
Touchthescreenwithyournger.
The touched screen is recognized as a touchscreen.
5.
Press "Enter" on the keyboard.
The “Tablet PC Settings” window reappears.
6.
Click "Calibrate".
A screen with a white background is displayed.
Attention
If using the monitor in a multiple monitor environment, select the monitor to calibrate the touch position for the
"Display" pull-down menu, and then click "Calibrate".
7.
Touchthecalibrationtarget(cross)forafewsecondswithyourngerand
release.
The calibration target appears on the screen 16 times, starting from the top left to top right and then
down to the bottom left to bottom right.
Note
For second or subsequent calibrations, the calibration target appears 4 times.
8.
After the touch position calibration has been completed, click "Yes" to save
the calibration data.
9.
Click "OK" to close the window.
14
Chapter 3 Touch Panel Settings
3-3. ConguringTouchPanelOperationSettings
1.
Open Windows Control Panel.
The method for opening Control Panel differs depending on the operating system. (See page 12)
2.
Click "Hardware and Sound" - "Pen and Touch".
“Pen and Touch” window appears.
Congure the touch panel operation settings in the “Pen and Touch” window. For detailed settings,
refer to the settings on each tab and Windows Help.
3.
After settings have been completed, click "OK" to close the window.
15
Chapter 4 Advanced Adjustment / Setting
Chapter 4 Advanced Adjustment / Setting
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
4-1. Basic Operation of the Setting Menu
1.
Displaying the Setting menu
1. Press to open the Setting menu.
2.
Adjustment / Setting
1. Use to select a menu to adjust or set, and press . The Sub menu appears.
2. Use to select an item to adjust or set, and press . The adjustment / setting menu appears.
3. Use to perform adjustment / setting, and press to apply the setting.
3.
Exiting
1. Select "Return" from the Sub menu, and press . The Setting menu appears.
2. Select "Exit" in the Setting menu, and press
. The Setting menu exits.
Note
The Setting menu can also be exited by pressing twice quickly.
16
Chapter 4 Advanced Adjustment / Setting
4-2. Color
Color Mode
This function allows easy selection of a desired mode according to monitor application.
Mode Purpose
User1 Select this to dene a desired set of parameter settings.
User2
sRGB Suitable for color matching with sRGB compatible peripherals.
Functions that can be adjusted differ depending on the color mode.
√: Adjustable -: Not adjustable
Function
Color Mode
User1 User2 sRGB
Brightness
Contrast -
Temperature -
Gamma -
Advanced
Settings
Hue -
Saturation -
Overdrive -
Gain -
Reset
Attention
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Perform the range adjustment rst when adjusting color for analog signals (see “Auto Range Adjust” (page
20)).
The same image may be seen in different colors on multiple monitors due to their monitor-specic
characteristics. Make ne color adjustment visually when matching colors on multiple monitors.
Brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Adjustable range
0 to 100
Note
If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
17
Chapter 4 Advanced Adjustment / Setting
Contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Note
In the contrast of 50, every color gradation is displayed.
When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
Perform the contrast adjustment in the following cases.
- If the image is too dark even when the brightness is set to 100 (Set the contrast to higher than 50.)
Temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of "White" and / or "Black" by a numerical
value. The value is expressed in degrees "K" (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like
the ame temperature. The gain preset values are set for each color temperature setting value.
Adjustable range
Off / 4000 K to 10000 K (specied by every 500 K unit, including 9300 K)
Note
The value shown in "K" is available only as reference.
Selecting "Advanced Settings" - "Gain" allows you to perform more advanced adjustment (see “Gain” (page
18)).
If you set to "Off", the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
When gain is changed, the color temperature is changed to "Off".
Gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal,
however, the variation rate is not proportional to the input signal. Maintaining the balance between the
input signal and the brightness of the monitor is called “Gamma correction".
Adjustable range
1.8 / 2.0 / 2.2
Note
If "sRGB" is selected for the color mode, "2.2" is displayed for the gamma value.
18
Chapter 4 Advanced Adjustment / Setting
Advanced Settings
Function Adjustable range Description
Saturation -50 to 50 This function allows you to adjust color saturation.
Note
Using this function may prevent some color gradations from
being able to be displayed.
The minimum value (-50) changes the screen to
monochrome.
Hue -50 to 50
This function allows you to adjust hue.
Note
Using this function may prevent some color gradations from
being able to be displayed.
Overdrive Enhanced / Standard
/ Off
This function allows you to set overdrive intensity based on the
use of the monitor.
You can reduce image lags by setting it to "Enhanced" when
displaying animated images.
Note
The overdrive function is disabled in the following cases:
- When the vertical scan frequency of input signals is more than
70 Hz
- When "Normal" or "Enlarged" is selected from "Screen Size"
(excluding the case that display resolution is 1920 × 1080).
Gain 0 to 100
The brightness of each color component red, green, and blue
is called "Gain". You can change the hue of "white" by adjusting
gain.
Note
Using this function may prevent some color gradations from
being able to be displayed.
The value of gain changes with that of color temperature.
When gain is changed, the color temperature is changed to
"Off".
Color Reset
Reset any color adjustments for the currently selected color mode back to the default settings.
19
Chapter 4 Advanced Adjustment / Setting
4-3. Screen
For D-Sub signal input For DisplayPort or DVI signal input
Screen Size
The image with the resolution other than the recommended resolution is displayed in full screen
automatically. You can change the screen size by using the “Screen Size” function.
Settings Function
Full Screen Displays an image in full screen. Images are distorted in some cases because the
vertical rate is not equal to the horizontal rate.
Enlarged Displays an image in full screen. In some cases, a blank horizontal or vertical
border appears to equalize the vertical rate and the horizontal rate.
Normal Displays images with the specied resolution.
Example: Image size 1024 × 768
Full Screen Enlarged Normal
(1920 × 1080) (1440 × 1080) (1024 × 768)
Smoothing
When an image is enlarged with a resolution other than recommended ("Full Screen" or "Enlarged" is
selected in "Screen Size"), the characters or lines of the displayed image may blur. This function
reduces this blurring effect.
Adjustable range
1 to 5
Note
Smoothing setting may not be required depending on the display resolution. (You cannot choose
"Smoothing".)
20
Chapter 4 Advanced Adjustment / Setting
Analog Adjustment
Screen ickering, display position, and size can be adjusted when the D-Sub signal is input.
Function Description
Auto Screen Adjust Screen ickering, display position, and size can be adjusted automatically. Selecting
Auto Screen Adjust” displays a message. Select “Yes” to enable this function.
Note
The automatic screen adjustment function works correctly when an image is fully
displayed over the entire displayable area of the screen. They do not work properly
in the below cases:
- When an image is displayed only on a part of the screen (command prompt
window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
When a signal is input into the monitor for the rst time or when a resolution or
vertical / horizontal scan frequency not used before is set, the screen is adjusted
automatically (only for signals with a resolution of 800 × 600 or higher).
Auto Range Adjust Every color gradation (0 to 255) can be displayed by automatically adjusting the signal
output level. Selecting “Auto Range Adjust” displays a message. Select “Yes” to enable
this function.
Clock
Flickering of vertical lines on the screen or part of the screen can be reduced.
Note
Use to make ne adjustments so as not to miss any adjustment points.
Phase
Flickering and blurring over the entire screen can be reduced.
Note
Flickering or blurring may not be eliminated depending on your PC or graphics
board.
After setting, adjust the “Clock” again if vertical bars appear.
Hor. Position
Ver. Position
The display position (horizontal and vertical) of the screen can be adjusted.
Note
Since the number of pixels and the pixel positions are xed on the LCD monitor,
only one position is provided to display images correctly. The position adjustment is
made to shift an image to the correct position.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Eizo FDF2382WT Manual de utilizare

Tip
Manual de utilizare

în alte limbi