Ubiquiti Networks UAP-AC Manualul utilizatorului

UAP-AC
Ubiquiti Networks
Marca
Ubiquiti Networks
Model
UAP-AC
Tip
Manualul utilizatorului
Enterprise WiFi System
Model: UAP-AC Outdoor
Introduction
Thank you for purchasing the Ubiquiti Networks
™
UniFi
™
Enterprise WiFi System. The UniFi Enterprise WiFi System
includes the UniFi Controller software, which allows you to
manage your wireless network using a web browser.
The UniFi Controller software and User Guide are available for
download at downloads.ubnt.com/unifi
This Quick Start Guide includes the warranty terms and is for
use with the UniFi AP AC Outdoor, model UAP-AC Outdoor.
The UniFi AP can be powered by any of the following:
• PoE GigE Adapter (included)
• 48V, PoE 802.3at compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
The UniFi AP also includes the necessary hardware for
mounting the unit on a wall or a pole.
Installation Requirements
• 13 mm wrench
• Shielded Category 5 (or above) cabling should be used
for all outdoor wired Ethernet connections and should be
grounded through the AC ground of the PoE.
We recommend that you protect your networks from
brutal outdoor environments and devastating ESD
attacks with industrial-grade shielded Ethernet cable from
UbiquitiNetworks. For more details, visit
www.ubnt.com/toughcable
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable is
designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.
Package Contents
UniFi AP AC Outdoor Mounting
Bracket
Pole Clamps
(Qty. 2)
Carriage Bolts
(M8x120, Qty. 4)
Flange Nuts
(M8, Qty. 4)
Enterprise WiFi System
Model: UAP-AC-Outdoor
PoE GigE Adapter
(48V, 0.5A Gigabit)
Power Cord Quick Start
Guide
System Requirements
• Microsoft Windows Vista, Windows 7, Windows 8, or
MacOSX
• Java Runtime Environment 1.6 (or above)
• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft
Internet Explorer 8 (or above)
Network Topology Requirements
• A DHCP-enabled network for the UniFi AP to obtain an
IPaddress (wireless clients will also obtain IP addresses after
deployment)
• A management station computer running the UniFi
Controller software, located either onsite and connected to
the same Layer2 network, or off-site in a cloud or NOC
or
Router
O-Site
Cloud/NOC
On-Site
Management Station
UAP-PRO
UAP-AC-Outdoor
UAP-AC
UAP-Outdoor
Sample Network Diagram
All UniFi APs support off-site management controllers.
For setup details, refer to the User Guide on the website:
documentation.ubnt.com/unifi
Hardware Overview
LED
LED Color Status
Flashing White
Initializing.
Steady White
Factory default, waiting to be integrated.
Alternating
White/Blue
Device is busy; do not touch or unplug it.
This usually indicates that a process such
as a firmware upgrade is taking place.
Quickly
Flashing Blue
This is used to locate an AP.
When you click Locate in the UniFi
Controller software, the AP will flash. It
will also display the location of the AP on
the map.
Steady Blue
Indicates the device has been successfully
integrated into a network and is working
properly.
Steady Blue
with occasional
flashing
Indicates the device is in an isolated state
(all WLANs are brought down until an
uplink is found).
*720-00046-01*
720-00046-01
Ports
Main
Ethernet Port
Reset
Button
Secondary
Ethernet Port
Secondary The Secondary port is a Gigabit Ethernet port used
for bridging.
Reset The Reset button serves two functions for the UniFi AP:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more then five seconds.
Main The Main port is a Gigabit Ethernet port used to connect
the power and should be connected to the LAN and DHCP
server. Power can be provided by any of the following:
• PoE GigE adapter (included)
• 48V, 802.3at compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
Hardware Installation
The recommended mounting of the UniFi AP AC Outdoor is
on a pole. Optionally, the UniFi AP may be installed on a wall
using additional hardware.
Pole Mount
1. Insert two Carriage Bolts into each Pole Clamp and install
the Flange Nuts as far down the bolts as necessary to
accommodate the pole.
Note: The mounting assembly can accommodate a
Ø 1.5" - 3.0" pole.
2. Attach one of the Pole Clamps to the pole by sliding the
Carriage Bolts around the pole and into the top two slots of
the Mounting Bracket.
3. Uniformly hand-tighten each Flange Nut. Ensure the Pole
Clamp is evenly clamped around the pole and tighten each
Flange Nut to approximately 25 N-m (18 lb-ft).
4. Attach the other Pole Clamp to the pole by sliding the
Carriage Bolts around the pole and into the bottom two
slots of the Mounting Bracket.
5. Uniformly hand-tighten each Flange Nut. Ensure the Pole
Clamp is evenly clamped around the pole and tighten each
Flange Nut to approximately 25 N-m (18 lb-ft).
6. Attach the UniFi AP to the Mounting Bracket:
a. Position the UniFi AP with the Mounting Bracket aligned
between the mounting tabs on the back of the UniFi AP.
b. Slide the UniFi AP downward into the grooves of the
Mounting Bracket until the snap pins engage and lock
the UniFi AP in place.
Wall Mount
To mount the UniFi AP on a wall, securely attach the Mounting
Bracket to the wall using four fasteners (not included).
Note: The Mounting Bracket must attach directly to a
stud or other structurally stable surface.
1. Locate the stud.
2. Position the Mounting Bracket on the stud, ensuring at least
two holes are centered on the stud.
3. Mark all four holes on the wall.
4. Drill pilot holes as necessary.
5. Secure the Mounting Bracket to the wall with four fasteners.
6. Attach the UniFi AP to the Mounting Bracket:
a. Position the UniFi AP with the Mounting Bracket aligned
between the mounting tabs on the back of the UniFi AP.
b. Slide the UniFi AP downward into the grooves of the
Mounting Bracket until the snap pins engage and lock
the UniFi AP in place.
Powering the UniFi AP
The UniFi AP can be powered by the included PoE GigE Adapter
or a compatible PoE switch.
1. Lift the locking tab of the Port Cover and slide the cover
down to remove it.
MAIN
RESET
SECONDARY
2. Connect an Ethernet cable to the Main port.
3. Replace the Port Cover.
Connecting to the PoE GigE Adapter
1. Connect the other end of the Ethernet cable to the
Ethernet port labeled POE on the PoE GigE Adapter.
2. Connect an Ethernet cable from your LAN to the Ethernet
port labeled LAN on the PoE GigE Adapter.
3. Connect the power cord the PoE GigE Adapter and to a
power outlet.
Connecting to a PoE Switch
Connect the other end of the Ethernet cable coming from the
UniFi AP directly to a PoE port on one of the following:
• 48V, 802.3at compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
TOUGHSwitch PRO Power Connection Diagram
Software Installation
Download and install the latest version of the UniFi Controller
software at downloads.ubnt.com/unifi and follow the
on-screen instructions.
After you have installed the software and run the UniFi
Installation Wizard, a login screen will appear for the UniFi
Controller management interface. Enter the Admin Name and
Password that you created and click Login.
You can manage your wireless network and view network
statistics using the UniFi Controller management interface. For
information on using UniFi Controller, refer to the User Guide
located on our website at documentation.ubnt.com/unifi
Specifications
UAP-AC-Outdoor
Dimensions 340 x 180 x 65 mm
Weight 1.55 kg (with Wall Mount)
2 kg (with Pole Mount)
Networking Interface (2) 10/100/1000 Ethernet Ports
Buttons Reset
Wi-Fi Standards 802.11 a/b/g/n/ac
Power Method PoE+(48V)
802.3at Supported
(Supported Voltage Range: 39 to 57VDC)
Power Supply 48V, 0.5A PoE Gigabit Adapter (Included)
Max. Power Consumption 22 W
BSSID Up to Four per Radio
Power Save Supported
Wireless Security WEP, WPA-PSK, WPA-TKIP,
WPA2 AES, 802.11i
Certications CE, FCC, IC
Mounting Wall/Pole (Kits Included)
Operating Temperature -10 to 55 °C
Operating Humidity 5 - 80% Condensing
Antennas
2.4 GHz 3 Integrated
(Supports 3x3 MIMO with Spatial Diversity)
5 GHz 3 Integrated
(Supports 3x3 MIMO with Spatial Diversity)
Max. TX Power
2.4 GHz 28 dBm
5 GHz 28 dBm
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal
physical, electromagnetic or electrical stress, including lightning
strikes, or accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.
Returns
No Products will be accepted for replacement or repair without obtaining
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS
during the warranty period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not
be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible
for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including
the Products) for buyer’s application and/or failure of products (including
the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO
THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations
Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
For MPE and antenna usage details, please visit our website at
www.ubnt.com/products
Industry Canada
This Class A digital apparatus complies with Canadian ICES-003.
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
Canada.
Pour réduire le risque d’interférence aux autres utilisateurs, le type
d’antenne et son gain doivent être choisies de façon que la puissance
isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire
pour une communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada exempts de
licence norme(s). Son fonctionnement est soumis aux deux conditions
suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais fonctionnement du
dispositif.
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
located or operating in conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être installé en
considérant une distance de séparation de toute personnes d’au moins
20 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre
antenne ou transmetteur.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.
Alert Sign (!) Follows CE Marking
Alert sign must be indicated if a restriction on use applied to the product
and it must follow the CE marking.
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Ubiquiti Networks UAP-AC Manualul utilizatorului

UAP-AC
Ubiquiti Networks
Marca
Ubiquiti Networks
Model
UAP-AC
Tip
Manualul utilizatorului
Descărcați PDF
raport

în alte limbi

Lucrări conexe

Alte documente