Parkside 300098 Operation and Safety Notes

PN EU M AT I C DRI LL PDBS 2 2 0 0 A3

IAN 300098

DRUCKLUFT-BOHRSCHRAUBER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ ΑΕΡΟΣ

Υποδείξεις χειρισμού και ασφαλείας

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

PISTOL PNEUMATIC DE GĂURIT

ȘI ÎNȘURUBAT

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

PNEUMATSKI ODVIJAČ

Upute za posluživanje i za Vašu sigurnost

Prijevod originalnih uputa za uporabu

PNEUMATIC DRILL

Operation and Safety Notes

Translation of the original instructions

GB / CY Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 15

RO Instrucţiuni de utilizare şi de siguranţă Pagina 27

GR

/

CY

Υποδείξεις χειρισμού και ασφαλείας

Σελίδα

39

DE

/

AT

/

CH

Bedienungs- und Sicherheitshinweise

Seite

51

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες της

συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

5 GB/CY

Table of contents

Introduction ................................................................................................................................... Page 6

Intended use ........................................................................................................................................ Page 6

Features ...............................................................................................................................................Page 6

Technical Data ....................................................................................................................................Page 6

Safety information for air tools ...................................................................................Page 7

Risks due to projecting parts...............................................................................................................Page 8

Risks from gripping / winding .............................................................................................................Page 9

Operating hazards .............................................................................................................................Page 9

Hazards due to repetitive motions ..................................................................................................... Page 9

Risks associated with accessories ......................................................................................................Page 9

Hazards in the work environment ......................................................................................................Page 10

Hazards due to dust and vapours .....................................................................................................Page 10

Noise hazards .....................................................................................................................................Page 10

Hazard due to vibration .....................................................................................................................Page 10

Additional safety instructions for pneumatic machinery ...................................................................Page 11

Commissioning ...........................................................................................................................Page 11

Inserting the bit or drill ........................................................................................................................Page 11

Connecting ..........................................................................................................................................Page 11

Adjusting the compressed air .............................................................................................................Page 12

Initial use ..............................................................................................................................................Page 12

Changing rotation ............................................................................................................................... Page 12

After initial use ...........................................................................................................................Page 12

Maintenance .................................................................................................................................Page 12

Cleaning and Care ...................................................................................................................Page 13

Information about warranty and service processing ...............................Page 13

Warranty terms ...................................................................................................................................Page 13

Scope of warranty ..............................................................................................................................Page 13

Processing of warranty claims ............................................................................................................ Page 13

Environmental instructions and disposal information ..............................Page 14

Declaration of Conformity ................................................................................................Page 14

6 GB/CY

Introduction

Pneumatic drill PDBS 2200 A3

Introduction

Congratulations! You have chosen a

high-quality device from our company.

Familiarise yourself with the product

before using it for the ﬁrst time. In addition, please

carefully refer to the operating instructions and the

safety advice below. Initial operation of this tool

must be performed by trained personnel.

KEEP OUT OF THE REACH OF CHILDREN!

Intended use

This air-powered drill is suitable for drilling into

plastic, wood, metal and similar materials. Only

use the product as described and for the indicated

purpose. Keep these instructions in a safe place.

When passing this product on to others, please

also include all the documents. Any use other than

the intended is prohibited and potentially dange-

rous. Damages resulting from noncompliance or mi-

suse are not covered by the warranty and are not

included in the manufacturer‘s liability. This device

has been designed for household use and may not

be used for commercial or industrial purposes.

Features

Verify contents are complete and the de-

vice is in perfect condition immediately

after unpacking. Do not use if the tool is

defective.

1

Keyed chuck

2

Drill head

3

On/ Oﬀ switch

4

Forward/reverse switch

5

Compressed air connection

6

Coupling

7

Air outlet

Accessories

8

Male coupling ¼“

9

Wrench

10

Bits

11

Bit extension inside bit box

12

Metal drill

Technical Data

Operating pressure: max. 6.8 bar

Speed max.: 2200

rpm

Collar: 1–10 mm

suitable for: Wood and metal drill bits

as well as standard bits

Air supply: via service unit with ﬁlter

pressure reducer and oil

atomiser

The following pictograms are used in these operating instructions / on the device:

Refer to operating manual! Oil daily

Note

Wear ear protection, dust mask, safety

glasses and protective gloves.

Follow warnings and safety notices! Compressed air hose

Never use hydrogen, oxygen, carbon

dioxide or other bottled gasses as an

power source

Dispose of packaging and device in an

environmentally friendly way!

7 GB/CY

Introduction / Safety information for air tools

Required air quality: puriﬁed, condensation-

free and oil nebulised

Compressors: with min. 50 L tank volume

Noise parameters

(per EN ISO 15744): approx. L

pA

: 91.3 dB(A)

approx. L

WA

: 102.3 dB(A)

Loss K: 3 dB

Vibration

(per EN 28927-2): 1.3 m / s²

Loss K: 1.5 m / s²

Safety information

for air tools

Basic safety measures must be

followed when using air tools to eliminate the risk

of ﬁre, electric shock and personal injury. Please be

sure to read and follow the notices in this operating

manual prior to the ﬁrst use and store them in a safe

place. The manufacturer assumes no liability for da-

mages or personal injury resulting from failure to

follow these operating instructions.

The hazards listed are foreseeable for general use of

handheld air impact drivers. However, the user must

also assess speciﬁc risks which may arise from its use.

DANGER! Keep your hands or

other limbs out of reach of rotating

parts. Injuries may otherwise occur.

CRUSHING HAZARD!

Keep hands away from the counter bearing

(e.g. box spanner) during use. This particularly

applies when removing screws in tight work en-

vironments.

RISK OF INJURY! Dis-

connect the compressed air before changing

tools, adjustments and maintenance.

EXPLOSION HAZARD!

Never use petrol or other ﬂammable liquids to

clean the air tool! Sparks could ignite residual

vapours inside the compressed air tool resulting

in explosion. Do not use the tool in explosive

environments with ﬂammable liquids, gasses or

dust. Never work on materials which are or po-

tentially could be highly ﬂammable or explosive.

In the cases of multiple hazards the safety in-

structions must be read and understood before

attaching, operating, repairing and exchanging

accessories and before working near the drill.

Otherwise severe bodily injuries may result.

The drill should only be set up, adjusted or

used by qualiﬁed and trained operators.

Never modify the drill. Modiﬁcations may re-

duce the eﬀectiveness of safety measures and

increase operator risks.

Do not lose the safety instructions – hand them

to the operator.

Never use a damaged machine on screw con-

nections.

Regularly maintain machines to verify all required

rated values and markings such as rated speed

or rated air pressure are legible on the machine.

If necessary, the user must contact the manufac-

turer for replacement labels for markings.

Only use the equipment for applications for

which it was designed!

Do not overburden the device.

Never use hydrogen, oxygen, car-

bon dioxide or other bottled gasses

to power this tool as doing so may

result in explosion, thus severe injuries.

Regularly maintain and clean the device as

required (see chapters „Maintenance“ and

Cleaning and care“).

Check the device for damage prior to initial

operation. Always verify the tool‘s proper con-

dition before every use.

Remain alert at all times! Unforeseen machine

movement due to reaction forces or the tool or

counter bearing breaking may result in injuries.

Unforeseen tool movements may result in ha-

zardous situations.

Crushing risk based on the torque between the

counter bearing and the work piece.

Keep hands away from the tool being used to

prevent the risk of injuries.

Only use holders and adapters in good condi-

tion and intended for use with the machines

described here.

Avoid an unnatural posture. Always maintain a

proper footing and balance. This will allow you

Weight: 1130 g

8 GB/CY

Safety information for air tools

to better control the electrical power tool in un-

foreseen circumstances.

Switch the device oﬀ when not in use.

Always wear personal protective

equipment and safety glasses. Wea-

ring personal protective equipment

such as dust mask, non-slip safety shoes, hard

hat or ear protectors, depending on the type of

air tool and its application, reduces the risk of

injuries.

Protect hoses from kinks, constrictions, solvents

and sharp edges. Keep hoses away from heat,

oil and rotating parts.

Replace damaged hoses immediately. A dama-

ged supply line may result in the air hose ﬂap-

ping about, possibly resulting in injuries.

Do not use the equipment when fatigued or un-

der the inﬂuence of drugs, alcohol or medica

tions.

Just a moment of carelessness when using this

equipment may result in serious injuries.

Do not directly inhale exhaust air. Keep eyes

away from exhaust air. Exhaust air from the air

tool may contain water, oil, metal particles or

contaminants from inside the compressor. This

may result in health damage.

CAREFUL WHEN PUT-

TING THE TOOL DOWN! Always put down

the device so the trigger is not activated. This

could potentially result in accidental activation

of the tool, which again could result in hazards.

Only use suitable accessories. These can be

purchased from the manufacturer. Using non-

OEM accessories may result in hazards.

Only use ﬁltered and regulated compressed air.

Dust, caustic vapours and / or moisture may

damage the motor of an air tool.

The hose must be constructed for a

minimum pressure of 6.8 bar or

125 PSI, but no less than 150 % of

the maximum pressure produced by the system.

The tool and supply line must be

equipped with a hose coupling to

completely release pressure when

disconnecting the coupling hose.

DANGER! Avoid contact with live lines. This

device is not insulated against electric shock.

Do not modify this equipment in any way wit-

hout the manufacturer‘s approval.

Only use the tool at the speciﬁed pressure

(max. 6.8 bar).

Disconnect the tool from the air supply after

each use and when not in use.

Discontinue use if the tool is leaking or in need

of repair.

Keep your working area clean and well lit.

Untidy or poorly lit working areas can result in

accidents. Doing so will allow you better control

of the equipment, particularly in unforeseen cir-

cumstances.

Only have the equipment

repaired by qualiﬁed specialist personnel using

OEM spare parts. This will ensure your device

remains safe to use.

Keep children and other individuals away from

the equipment during use. Distractions can

cause you to lose control of the equipment.

Wear suitable clothing. Do not wear loose

clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose

clothing, jewellery or long hair can become

caught in moving parts.

Put down trigger and equipment in the event of

unexpected compressor failure.

Never use or store the tool in humid, dusty lo-

cations or near water, other ﬂuids or hazar-

dous gases.

If possible, use a condensate trap or regularly

drain condensate (water) from hoses and pipes

before and during air tool use.

Secure work pieces. Use clamps or a vice to

secure the work piece. Holding the work piece

in your hand or pressing it against your body

will not allow for safe use of the equipment.

ATTENTION! An undersized com-

pressed air system may reduce the

eﬃciency of your equipment.

Risks due to projecting parts

If the work piece, one of the accessories or the

tool itself breaks, parts may be projected at

great speeds.

9 GB/CY

Safety information for air tools

Always wear impact-resistant eye protection

when using the drill. The level of protection

required should be asses for each individual

application.

The wrench must be removed before drilling.

Be sure the work piece is properly secured.

Risks from gripping / winding

Risks from gripping / winding may result in suf-

focation, scalping and / or cuts if loose clothing,

jewellery, necklaces, hair or gloves are not kept

away from the machine and its accessories.

Always wear impact-proof eye protection dur-

ing operation and when performing repairs or

maintenance and replacing accessories on the

drill or the thread cutter. The level of required

protection required should be assessed individ-

ually for each application.

Rotating drives and extensions may easily catch /

wind rubberised or metal reinforced gloves.

Never wear loose gloves or gloves with cut or

worn ﬁngers.

Never hold on to the drive, collect or the drive

extension.

Keep hands away from the rotating drive.

Operating hazards

During use of the device the operator‘s hands

could be exposed to dangers, e.g. cuts, abra-

sions and heat. Wear suitable gloves to protect

hands.

The operator and maintenance personnel must

be physically capable to manage the weight

and power of the machine.

Hold the machine correct: be prepared to coun-

teract typical or sudden movements – keep both

hands ready.

Be sure your body is well balanced and maintain

a solid stance.

High reaction torques may arise in the event of

a jam, which could be caused by excessive

loads on the drill, the drill twisting inside the

material being worked on, or the drill penetrat-

ing the material being worked on.

If tools are required to absorb the reaction tor-

que, use a suspension attachment whenever

possible. If this is not possible, we recommend

side handles for machines with straight handle

and pistol grip. At any rate we recommend

using tools to absorb if it is greater than 4 Nm

for machines with straight handles, greater

than 10 Nm for machines with pistol grip.

Keep hands away from the rotating chuck and

the rotating drill.

In the event of power failure release the start-

or stop control.

Only use the lubricants recommended by the

manufacturer.

Always wear protective goggles. Wearing

protective gloves and protective clothing is

recommended.

Hazards due to

repetitive motions

When using a drill

the operator may experience

discomfort in

hands, arms, shoulders, neck or

other body parts whilst performing work-related

tasks.

Maintain a comfortable position whilst using

this tool, be mindful of a secure grip and avoid

awkward positions or positions making it diﬃ-

cult to maintain your balance. The operator

should

change his posture during extended periods of

use, which may help to prevent discomfort and

fatigue.

If the operator experiences symptoms such as

persistent malaise, discomfort, palpitations, pain,

tingling, numbness, a burning sensation or stiﬀ-

ness, these warning signs should not be ignored.

The user should consult a qualiﬁed healthcare

professional.

Risks associated with

accessories

Disconnect machine from the power supply

before changing a tool or accessory.

Only use accessories and materials sizes and

types recommended by the manufacturer; do

10 GB/CY

Safety information for air tools

not use other accessory and material types

and sizes.

Avoid direct contact with the machine tool dur-

ing and after use, as it may become very hot

or sharp-edged.

Hazards in the work

environment

Slipping, tripping and falls are main causes of

injuries at the workplace. Be mindful of surfaces

which may have become slippery during ma-

chine use, and of tripping hazards caused by

the air- or hydraulic hose.

Proceed with caution in unfamiliar surroundings.

These may hold hidden dangers due to electri-

cal cables or supply lines.

The drill is not suitable for use in explosive envi-

ronments and is not insulated against contact

with electrical power sources.

Verify there are no electrical lines, gas lines,

etc. which may result in a hazard in the event

they are damaged during machine use.

Hazards due to dust

and vapours

Dusts and vapours generated by use of drill

connections may result in damage to the health

(e.g. cancer, birth defects, asthma and / or der-

matitis); it is imperative to perform a risk assess-

ment for these hazards and implement the

respective regulatory mechanisms.

The risk assessment should include dust genera-

ted from machine use and dust in the area pos-

sibly being blown around.

Use and maintain the drill or thread cutter as

recommended in these instructions to minimise

the release of dust and vapours.

Exhaust air must be discharged so the amount

of dust being blown about in a dusty environ-

ment is minimised.

If dust or vapours are generated the principal

task must be to monitor them in the area where

they are released.

All machine mounting parts or accessories in-

tended to collect, extract or eliminate airborne

dust or vapours should be used and maintained

according to manufacturer instructions.

Select, maintain and replace consumables and

machine tools as recommended in these in-

structions to prevent an unnecessary increase

in the production of dust or vapours.

Use respiratory dust equipment as required by

labour- and health regulations.

Noise hazards

With inadequate ear protectors the impact of

high noise levels may result in permanent hea-

ring damage, hearing loss and other problems,

e.g. tinnitus (ringing, whistling or buzzing in the

ear).

It‘s imperative to perform a risk assessment for

these hazards and implement the suitable regu-

latory mechanisms.

Suitable regulatory mechanisms to minimise the

risk include measures such as using insulation

to prevent pinging sounds on work pieces.

Use heating protection as required by labour-

and health regulations.

The drill must be operated and maintained as

recommended in these instructions to prevent

an unnecessary increase in the noise level.

If the drill features a silencer, always ensure it is

available when using the drill and in good wor-

king order.

Select, maintain and replace consumables and

machine tools as recommended in these instruc-

tions to prevent an unnecessary increase in the

sound level.

Hazard due to vibration

Exposure to vibration may cause damage to

the nerves and disturb blood circulation in hands

and arms.

Wear warm clothes when working in cold envi-

ronments and keep hands warm and dry.

11 GB/CY

Safety information for air tools / Commissioning

If you notice your skin on ﬁngers or hands beco-

ming numb, tingling, hurting or becoming white,

stop working with the machine and consult a

physician.

Operate and maintain the drill as recommen-

ded in this manual to prevent an unnecessary

increase in vibration.

Do not allow the drill to rattle on the material,

as this will most likely signiﬁcantly increase vi-

bration.

Do not use work or poorly ﬁtting sockets or ex-

tensions, as these are very likely to signiﬁcantly

increase vibration.

Select, maintain and replace consumables and

machine tools as recommended in these in-

structions to prevent an unnecessary increase

in vibration.

Whenever possible, use a stand, clamp or an

equaliser to support the weight of the machine.

Do not grip the machine too tightly but ﬁrmly,

maintaining the necessary hand reaction forces,

as the vibration hazard typically increases when

tightening the grip.

Additional safety instructions

for pneumatic machinery

Compressed air can result in serious injuries.

- Always close the air supply, release pressure

from the hose, and disconnect the machine

from the compressed air supply when the ma-

chine is not in use, before switching accesso-

ries or when performing repairs.

- Never aim the air ﬂow at yourself or others.

Hoses ﬂapping about can result in serious inju-

ries. Therefore always inspect hoses and their

fasteners for damage and a secure ﬁt.

Direct cold air away from hands.

If using universal swivel couplings (coupling

discs) always use locking pins and use whip-

check hose safety cables for protection in the

event the connection between the hose and the

machine or in between hoses fail.

Be sure not to exceed the maximum pressure

speciﬁed on the machine.

Never carry pneumatic tools by the hose.

Commissioning

Note: The device is fully functional as delivered.

Inserting the bit or drill

Loosen the keyed chuck

1

using the wrench

9

(see Fig. A).

Now insert the bit extension

10

as far as possi-

ble into the keyed chuck

1

and attach the

bit

11

(see Fig. A).

To secure the bit extension

10

, tighten the

keyed chuck

1

using the wrench

9

(see Fig. B).

Ensure the bit extension

10

and the bit

11

are

seated securely. Insert the drill as in these steps

(see Fig. A and C).

Connecting

Note: only use connection hoses with a minimum

inside diameter of 9 mm.

Wrap the coupler

8

with Teﬂon tape (not in-

cluded) before screwing it into the compressed

air unit. Wrap the tape around the thread as

tight as possible. This will minimise the likeli-

hood of air leaking and optimise the work

process.

Screw the plug nipple

8

into the connection

thread of the power drill (see Fig. D).

Tighten the connection using a pair of pliers.

Now attach the air hose to the plug nipple

8

using some force until the hose locks into

place.

ATTENTION! Ensure that the com-

pressed air hose is ﬁrmly seated. A

loose hose whipping about out of

control presents a major hazard. Also ensure

the two screw connections between the coup-

ling and device are secure.

12 GB/CY

Commissioning / After initial use / Maintenance

Adjusting the compressed air

Note: this device is designed for an operating

pressure of up to 6.8 bar and a compressor with

the minimum air ﬂow speciﬁed in the technical spe-

ciﬁcations. When setting the air pressure, remem-

ber the pressure drops by approx. 0.6 bar with a

hose length of 10 m and an inner diameter of

9 mm.

Only use ﬁltered, lubricated and regulated

compressed air.

Initial use

Activate the On / Oﬀ switch

3

to start using

the device.

Release the On/ Oﬀ switch

3

to switch the

device oﬀ.

Changing rotation

ATTENTION! The device must come to a

complete standstill before changing the direc-

tion of rotation.

ATTENTION! A machine rotating in an unex-

pected direction can be dangerous. Always

pay attention and use care.

Note: The power drill is designed for clock-

wise/counter-clockwise rotation. Use the

forward/reverse switch

4

to change the

direction of rotation of the power drill.

Set the forward/reverse switch

4

to position F

to switch to clockwise rotation.

Set the forward/reverse switch

4

to position R

to switch to counter-clockwise mode.

After initial use

Once the task has been ﬁnished the device must be

disconnect from the compressed air supply

5

.

Brieﬂy activate the On / Oﬀ switch

3

on the

device to bleed any residual compressed air.

Now pull back the safety on the connection

coupling of your compressed air hose.

Now remove the hose from the plug nipple

8

.

Careful when putting the device

down. Always put down the device so it does

not rest on the trigger. This could potentially re-

sult in inadvertent activation of the tool, which

in turn could result in hazards.

Maintenance

ATTENTION! All maintenance must be per-

formed by trained individuals. Follow the speciﬁed

maintenance instructions to ensure a long life and

proper operation of this quality product.

Disconnect equipment from the compressed air

source when performing maintenance and care.

Check the condition of wear and tear items

and accessories with each maintenance.

Note: Daily cleaning and regular lubrication

are an absolute necessity for smooth operation.

Only use special tool oil with a high viscosity

(thin ﬂuid). Oil for compressed air tools or

SAE10-20 motor oil are suitable.

ATTENTION! Do not use other (especially

high viscosity) lubricants. Malfunctions or per-

manent damage may otherwise occur.

The following lubricating options are

available:

a) via oil-mist generator

To use the oil-mist generator plug the plug

nipple

8

directly into the equipment and con-

nect with your air hose.

b) by hand

Alternatively you can also manually lubricate

your equipment (not recommended).

To do so, remove the screw plug on the oil ﬁller

port.

Apply 3–5 drops of oil to the compressed air

connection before using the compressed air

tool

4

.

If the air tool has not been used for several

days 5–10 drops of oil must be added to the

air connection

5

.

Note: Regular lubrication is impe-

rative to ensure the longest possible

life for your compressed air device.

Always store your air tools / equipment in dry

locations.

13 GB/CY

... / Cleaning and Care / Information about warranty and service processing

No maintenance is required beyond the above

lubrication and cleaning.

Cleaning and Care

Never clean with ﬂuids such as petrol, solvents

or water.

Do not allow liquids to enter the equipment.

Only clean the tool with a dry cloth.

Information about warranty

and service processing

Creative Marketing Consulting GmbH

warranty

Dear customer, the warranty for this device is 3

years from the date of purchase. In the event of

product defects you have legal rights against the

retailer of this product. Your legal rights are not li-

mited in any way by our warranty detailed below.

Warranty terms

The warranty period begins on the date of purchase.

Please keep the original sales receipt in a safe lo-

cation. This document is required as your proof of

purchase.

Should this device show any fault in materials or

manufacture within three years from the date of

purchase, we will repair or replace it - at our choice -

free of charge to you. Warranty services require

the defective device and the proof of purchase (sales

receipt) to be presented within the three-year period

along with a brief written description of the defect

and when it occurred.

If the defect is covered by our warranty, we will re-

turn the repaired device or replacement thereof. A

repair or exchange of the device does not extend a

new warranty period.

Scope of warranty

The device has been manufactured to strict quality

guidelines and meticulously examined before delivery.

The warranty applies to faults in material or manuf-

acture. This warranty does not apply to product

parts subject to normal wear and tear and which

can therefore be considered as wear items, or to

damage to fragile parts, e.g. switches, storage bat-

teries or glass parts.

This warranty becomes void if the device has been

damaged or improperly used or maintained. All in-

structions provided in the operating instructions must

be followed strictly to constitute proper use of the

product. Applications and actions which the opera-

ting instructions warn of or advise against must be

avoided without fail.

This product is intended for private, non-commercial

use only. The warranty is void in the case of inap-

propriate and improper handling, use of force and

of any intervention which was not carried out by

our authorized service branch.

Processing of warranty claims

Please follow the instructions below to ensure quick

processing of your matter:

When inquiring about your product please have

your receipt and product number (e.g. IAN) ready

as your proof of purchase.

The item number can be found on the type plate,

engraving, the cover page of your instructions (bot-

tom left) or the decal at the back or bottom.

In the event of malfunctions or other defects please

ﬁrst contact the service department below by

phone or e-mail.

A product recorded as defective, along with the

proof of purchase (sales receipt) and a description

of the defect and when it occurred, can then be re-

turned free of charge to you to the service address

provided.

Note:

Visit www.lidl-service.com to download

this and many other manuals, product

videos and software.

14 GB/CY

Information about ... / Environmental instructions and ... / Declaration of ...

How to contact us:

GB

Name: C. M. C. GmbH

Website: www.cmc-creative.de

E-mail: ser[email protected]

Phone: 0-808-189-0652

(standard German landline

rates apply)

Fax: 0-808-189-0652

Registered oﬃce: Germany

CY

Όνομα: C. M. C. GmbH

Διεύθυνση

διαδικτύου: www.cmc-creative.de

E-Mail: ser[email protected]

Τηλέφωνο: +49 (0) 6894 9989752

(κανονική χρέωση σταθερού

δικτύου Γερμανίας)

Έδρα: Γερμανία

I AN 3 0 0 0 9 8

Please note the following address is not a service

address.

Please ﬁrst contact the above service address.

Address:

C. M. C. GmbH

Katharina-Loth-Str. 15

66386 St. Ingbert

GERMANY

Environmental instructions

and disposal information

Don‘t waste, recycle!

Equipment, accessories and packaging

should be recycled in an environmen-

tally friendly manner.

Do not dispose of the compressed air tool through

your household waste, or throw into ﬁre or water. If

possible, non-operational devices should be recy-

cled. Contact your local retailer for information.

Declaration of Conformity

We,

C. M. C. GmbH

Documentation oﬃcer: Alexander Hoffmann

Katharina-Loth-Str. 15

66386 St. Ingbert

GERMANY

declare on our sole responsibility the product

Pneumatic drill

Item number: 2124

Year of manufacture: 2018 / 34

IAN: 300098

Model: PARKSIDE PNEUMATIC DRILL

PDBS 2200 A3

to meet the basic safety requirements of European

Directives

Machinery Directive

EC Directive 2006 / 42 / EC

and its amendments.

The conformity assessment is based on the follow-

ing harmonised standards:

DIN EN ISO 11148-3:2012

St. Ingbert, 04.04.2018

i. A. Alexander Hoffmann

- Quality assurance -

15 HR

Popis sadržaja

Uvod .............................................................................................................................................. Stranica 16

Namjena ........................................................................................................................................ Stranica 16

Oprema ......................................................................................................................................... Stranica 16

Tehnički podaci ............................................................................................................................. Stranica 16

Sigurnosne upute za pneumatske alate ......................................................... Stranica 17

Opasnosti zbog letećih dijelova .................................................................................................. Stranica 19

Opasnosti zbog zahvatanja / namatanja ................................................................................... Stranica 19

Opasnosti kod pogona ................................................................................................................ Stranica 19

Opasnosti zbog pokreta koji se ponavljaju ................................................................................ Stranica 20

Opasnosti zbog pribora ............................................................................................................... Stranica 20

Opasnosti na radnom mjestu ....................................................................................................... Stranica 20

Opasnosti zbog prašine i pare .................................................................................................... Stranica 20

Opasnosti zbog buke ................................................................................................................... Stranica 20

Opasnosti zbog vibracije ............................................................................................................. Stranica 21

Dodatne sigurnosne upute za pneumatske strojeve ................................................................... Stranica 21

Stavljanje u pogon ............................................................................................................ Stranica 21

Umetanje bita ili svrdla ................................................................................................................. Stranica 21

Izrada priključaka ......................................................................................................................... Stranica 22

Namještanje tlačnog zraka .......................................................................................................... Stranica 22

Stavljanje u pogon ........................................................................................................................ Stranica 22

Mijenjanje smjera okretaja ........................................................................................................... Stranica 22

Poslije stavljanja u pogon ........................................................................................... Stranica 22

Održavanje ............................................................................................................................. Stranica 23

Čišćenje i održavanje ...................................................................................................... Stranica 23

Upute o jamstvu i odvijanje servisa ................................................................... Stranica 23

Uvjeti jamstva ................................................................................................................................ Stranica 23

Opseg jamstva .............................................................................................................................. Stranica 24

Postupak u slučaju jamstva ........................................................................................................... Stranica 24

Upute za zaštitu okoliša i napomene za zbrinjavanje ....................... Stranica 25

EG-Izjava o sukldnosti .................................................................................................... Stranica 25

16 HR

Uvod

Pneumatski odvijač PDBS 2200 A3

Uvod

Čestitamo! Time ste se odlučili za jedan

vrlo kvalitetan uređaj iz naše kuće. Prije

prvog stavljanja u pogon, upoznajte

se s proizvodom. Za to pažljivo pročitajte slijedeće

upute za korištenje i sigurnost. Stavljanje u pogon

ovog alata moraju vršiti samo upućene osobe.

NE DOZVOLITE DA DOĐE U DJEČJE RUKE!

Namjena

Ova bušilica koja radi sa komprimiranim zrakom

pogodna je za bušenje plastike, drva, metala i slič-

nih materijala. Koristite proizvod samo u skladu s

navedenim uputama i u navedene svrhe. Brižno

čuvajte ove upute. Ako proizvod dajete nekoj dru-

goj osobi, predajte joj i sve upute. Svaka primjena

koja odstupa od namjenske uporabe je zabranjena

i potencijalno opasna. Štete koje nastaju zbog

nepoštivanja uputa ili zloupotrebe nisu pokrivene

jamstvom i ne spadaju u opseg odgovornosti koje

snosi proizvođač. Uređaj je dizajniran za kućnu

upotrebu i ne smije se koristiti u komercijalne svrhe

ili industrijski.

Oprema

Neposredno nakon otvaranja provjerite

opseg pošiljke, kao i da li je uređaj u be-

sprijekornom stanju. Uređaj ne koristite,

ako je oštećen.

1

stezna glava sa zupčastim vijencem

2

glava bušilice

3

prekidač za uključivanje /isključivanje

4

preklopnik smjera vrtnje

5

priključak za komprimirani zrak

6

spojni dio

7

izlaz zraka

Pribor

8

utična nazuvoca ¼“

9

ključ za zatezanje

10

produžetak bitova u kutiji bitova

11

bitovi

12

svrdlo za metal

Tehnički podaci

Pogonski tlak: maks. 6,8 bara

Broj okretaja maks.: 2200 min

-1

Prihvat: 1–10 mm

prikladan za: svrdla za drvo i metal

kao i uobičajene bitove

U ovim uputama za uporabu / na uređaju se koriste sljedeći simboli:

Pročitajte upute za korištenje! Dnevno stavljajte ulje

Napomena

Nosite zaštitu za sluh, masku za

zaštitu od prašine, zaštitne očale i

zaštitne rukavice.

Obratiti pozornost na upozoravajuće i

sigurnosne upute!

Crijevo tlačnog zraka

Ne upotrebljavajte nikada vodik, kisik,

ugljični dioksid ili drugi plin u bocama

kao izvor energije.

Ambalažu i uređaj zbrinite na

ekološki prihvatljiv način!

17 HR

Uvod / Sigurnosne upute za pneumatske alate

Dovod zraka: preko jedinice za održa-

vanje s reduktorom tlaka

ﬁltera i raspršivača ulja

Potrebna kvaliteta zraka: pročišćen, bez konden-

zata i raspršivaća ulja

Kompresori: s najmanje. 50 l volu-

mena spremnika

Krakteristične vrijednosti

buke (prema

EN ISO 15744): cca. L

pA

: 91,3 dB(A)

cca. L

WA

: 102,3 dB(A)

Nesigurnost K: 3 dB

Vibracije

(u skladu s EN 28927-2): 1,3 m / s²

Nesigurnost K: 1,5 m / s²

Sigurnosne upute za

pneumatske alate

Ako se upotrebljavaju pneu-

matski alati, moraju se slijediti osnovne mjere opreza,

kako bi se isključio rizik od vatre, strujnog udara i

ozljeda za osobe. Molimo bezuvjetno pročitajte prije

prvog korištenja ove upute za korištenje i pridržavajte

ih se, te ih dobro pospremite. Za štete ili tjelesne

ozljede, koje proizlaze zbog nepridržavanja ovih

uputa za korištenje, proizvođač ne preuzima ni-

kakvu odgovornost.

Navedene opasnosti se mogu predvidjeti kod opće

upotrebe ručnih pneumatskih udarnih odvijača. Osim

toga mora korisnik procijeniti speziﬁčne rizike, koji

mogu nastati zbog korištenja.

OPASNOST! Držite ruke i druge

udove daleko od rotirajućih dijelova.

U protivnom prijeti opasnost od ozl-

jeda.

OPASNOST OD

PRIGNJEČENJA! Držite na udaljenosti svoje

ruke za vrijeme rada protuležaja (npr. okasti

ključ). To osobito važi kod odvrtanja vijka u

skučenom radnom prostoru.

OPASNOST OD

OZLJEDA! Prije izmjene alata, podešavanja i

radova održavanja prekinite dovod tlačnog

zraka.

OPASNOST OD

EKSPLOZIJE! Ne koristite nikada za čišćenje

pneumatskih uređaja benzin ili druge zapaljive

tekućine! Preostala para u pneumatskom uređaju

se može zapaliti iskrom i dovesti do eksplozije

pneumatskog uređaja. Ne radite s uređajem u

području gdje prijeti opasnost od eksplozije,

gdje se nalaze zapaljive tekućine, plinovi ili

prašina. Ne obrađivajte materijale, koji se mogu

lako zapaliti ili eksplodirati.

Za višestruke opasnosti moraju se pročitati i

razumjeti sigurnosne upute prije ugradnje, po-

gona, popravka, održavanja i prije zamjene

opreme, kao i prije rada u blizini bušilice. U

protivnom to može dovesti do teških tjelesnih

ozljeda.

Bušilica treba biti postavljena, podešena i

korištena isključivo od kvaliﬁciranih i educiranih

operatera.

Bušilica se ne smije mijenjati. Promjene mogu

smanjiti učinkovitost sigurnosnih mjera i pove-

ćati rizik za operatera.

Sigurnosne upute ne smiju biti izgubljene –

predajte ih osobama operaterima.

Nikada ne koristite oštećenu bušilicu.

Stroj treba redovito održavati, kako bi provjerili,

da li su sve potrebne vrijednosti i oznake kao npr.

nazivni broj okretaja ili nazivni tlak zraka čitljivo

označeni na stroju. Ako je potrebno, korisnik se

mora obratiti proizvođaču, kako bi dobio rezer-

vne naljepnice za oznake.

Koristite uređaj samo u područjima za koje je

koncipiran!

Ne preopteretite uređaj.

Ne upotrebljavajte nikada vodik,

kisik, ugljični dioksid ili drugi plin u

bocama kao izvor energije za ovaj

alat, jer to može dovesti do eksplozije i na taj

način do teških ozljeda.

Održavajte i čistite uređaj redovito, kao što je

propisano (vidi odlomak „Održavanje“ kao i

„Čišćenje i njega“).

Prije stavljanja u pogon, provjerite uređaj na

moguća oštećenja. Provjerite prije svake upo

trebe,

dali se uređaj nalazi u besprijekornom stanju.

Težina: 1130 g

18 HR

Sigurnosne upute za pneumatske alate

Budite uvijek pažljivi! Neočekivano kretanje

stroja kao posljedica snaga reakcije ili loma

umetnutog alata ili protuležaja može dovesti

do ozljeda.

Neočekivano kretanje umetnutog alata može

izazvati opasnu situaciju.

Postoji rizik prignječenja zbog okretnog momenta

između protuležaja i dijela koji se obrađuje.

Držite Vaše ruke podaleko od alata koji se kori-

sti, jer inače postoji rizik od ozljeda.

K

oristite samo obličja i adaptere, koji su u dobro

m

stanju i prikladni za upotrebu s ovdje opisanim

strojem.

Izbjegavajte nenaravan polažaj tijela. Vodite

računa o tome da sigurno stojite na tlu i o

državate

vlastitu ravnotežu. Na taj način bolje možete kon-

trolirati električni alat, posebno u neočekivanim

situacijama.

Isključite uređaj, ako ga više ne koristite.

Nosite osobnu zaštitnu opremu i

uvijek zaštitne naočale. Nošenje

osobne zaštitne opreme, kao maske

za prašinu, protuklizne zaštitne cipele, zaštitnu

kacigu ili štitnik za uši, ovisno o vrsti i upotrebi

pneumatičnog alata, smanjuje rizik od ozljeda.

Zaštitite crijevo od presavijanja, sužavanja, ot-

apala i oštrih uglova. Držite crijava podalje od

vrućine, ulja i rotirajućih dijelova.

Smjesta zamijenite oštećeno crijevo. Oštećeni

kabel napajanja može dovesti do nekontroliranog

udaranja tlačnog crijava i prouzročiti ozljede.

Ne koristite uređaj ako ste umorni ili pod utje-

cajem droga, alkohola ili lijekova. Jedan trenutak

nepažnje za vrijeme korištenja uređaja, može

uzrokovati teške ozljede.

Ne udište direktno ispušni zrak. Izbjegavajte

da Vam ispušni zrak dođe u oči. Ispušni zrak

pneumatičnog uređaja može sadržavati vodu,

ulje, metalne čestice ili zagađenje iz kompres

ora.

To može prouzrokovati zdravstvene probleme.

BUDITE OPREZNI

KOD ODLAGANJA UREĐAJA! Odložite

uređaj uvijek tako, da ne leži na okidnom me-

hanizmu. Pod određenim okolnostima to bi mo-

glo dovesti do nenamjernog aktiviranja

uređaja, što opet može izazvati opasnosti.

Smije se koristiti samo prikladna oprema. To se

može kupiti kod proizvođača. Neka druga osim

originalne opreme može dovesti do opasnosti.

Koristite samo ﬁltrirani i regulirani tlačni zrak.

Prašina, nagrizjuća para i / ili vlaga mogu oštetiti

motor jednog pneumatičnog alata.

Crijevo mora biti koncipirano za je-

dan tlak od najmanje 6,8 bara ili

125 psi, ali najmanje na 150 % od

maksimalnog pritiska proizvedenog u sustavu.

Alat i dovodno crijevo moraju biti

opremljeni spojkom crijeva, tako se

kod odvajanja spojke crijeva, tlak u

potpunosti razgradi.

OPASNOST! Izbjegavajte kontakt s vodom

napona. Ovaj uređaj nije izoliran od električnog

udara.

Bez dozvole proizvođača alat se ne smije ni

na bilo koji način mijenjati.

Koristite alat samo s propisanim pritiskom

(6,8 bara).

Alat se treba nakon upotrebe uvijek odvojiti od

dovoda zraka.

Ako alat nije potpuno nepropusan za zrak ili

se mora popravljati, ne smije se više koristiti.

Vodite uvijek računa o tome, da Vaše radno

mjesto bude čisto i dobro osvjetljeno. Nered i

ne osvjetljeno područje rada, može uzrokovati

nezgode. Na taj način možete bolje kontrolirati

uređaj, naročito u neočekivanim situacijama.

Prepustite popravke

uređaja isključivo stručnom osoblju i s original-

nim rezervnim dijelovima. Time ćete zadržati

sigurnost Vašeg uređaja.

Držite djecu i druge osobe tijekom korištenja

podalje od uređaja. Kod nepažnje, mogli bi iz-

gubiti kontrolu nad uređajem.

Nosite prikladnu odjeću. Ne nosite široku odjeću

ili nakit. Držite kosu, odjeću i rukavice dalje od

pomičnih dijelova. Opuštena odjeća, nakit ili

duga kosa mogu biti zahvaćeni od pomičnih

dijelova.

Okidač i uređaj udaljiti u slučaju neočekivanog

kvara na kompresoru.

Ne koristite i ne pohranjujte alat nikada na

vlažnim, prašnjavim mjestima ili u blizini vode,

drugih tekućina ili opasnih plinova.

19 HR

Sigurnosne upute za pneumatske alate

Koristite po mogućnosti separatora konenzata

ili redovito praznite crijeva i cijevne vodove prije

i za vrijeme pogona pneumatičnih uređaja od

kondenzata (vode).

Učvrstite predmete koje obrađivate. Koristite

zatezne naprave ili škripac, kako bi učvrstili

predmet. Ako držite predmete koje obrađivate

s rukom ili pritisnete na tijelo, ne možete sigurno

koristiti uređaj.

POZOR! Jedan nedovoljno dimen-

zionirani sustav tlačnog zraka može

smanjiti učinkovitost Vašeg uređaja.

Opasnosti zbog letećih dijelova

Kod loma predmeta koji se obrađiva ili jednog

od dodatne opreme ili pak dijela strojnog

alata mogu krhotine letjeti velikom brzinom.

Za vrijeme rada bušilice treba se uvijek nositi

zaštita za oči otporna na udarce. Stupanj

potrebne zaštite se treba za svaku pojedinu

primjenu posebno procijeniti.

Ključ za zatezanje se mora privući prije

početka bušenja.

Uvjerite se da je predmet kojeg obrađujete

sigurno učvrđćen.

Opasnosti zbog zahvatanja /

namatanja

Opasnosti zbog zahvatanja / namatanja mogu

dovesti do gušenja, skalpiranja i / ili ozljede

zbog rezanja, ako se široka odjeća, osobni na-

kit, lančići, kosa ili rukavice ne drže na udalje-

nosti od stroja i njegovih dodatnih dijelova.

Za vrijeme rada, popravka, održavanja ili

zamjene opreme bušilice ili rezača navoja,

treba se uvijek nositi zaštita za oči otporna na

udarce. Stupanj potrebne zaštite se treba za

svaku pojedinu primjenu posebno procijeniti.

Kod rotirajućih pogonskih oblika i produžnih

dijelova može lagano doći do zahvaćanja /

namatanja gumiranih ili metalno pojačanih ru-

kavica.

Ne nosite rukavice koje labavo sjede ili ruka-

vice kojima su odrezani ili potrgani prsti.

Ne držite nikada čvrsto pogonski dio, prihvat

ili produžetak pogonskog dijela.

Držite Vaše ruke daleko od rotirajućeg pogona.

Opasnosti kod pogona

Kod pogona stroja mogu biti ruke korisnika

izložene opasnosti kao npr. rezanju, abraziji i

toplini. Nosite odgovarajuće rukavice za za-

štitu ruku.

Operator i osoblje za održavanje moraju biti

ﬁzički u stanju da vladaju s veličinom, težinom i

snagom stroja.

Držite stroj ispravno: budite spremni, da savla-

date uobičajni i nagli pokret – držite obje ruke

spremnim.

Pazite na to, da Vam je tijelo u ravniteži i da

sigurno i čvrsto stojite.

Visoke reakcije zakretnog momenta mogu se

pojaviti u slučaju blokiranja, što može biti uzro-

kovano pretjeranim djelovanjem opterećenja

na svrdlo u materijalu koji se obrađiva strojem

ili kod prolaza svrdla kroz materijal.

U slučajevima, gdje su potrebna pomagala za

prihvat reaktivnog okretnog momenta, prepo-

ruča se, ako je moguće da uvijek koristite na-

pravu za objesiti. Ako to nije moguće,

preporučuju se za strojeve s ravnim drškama

bočne drške i strojevi s revorver drškom. U sva-

kom slučaju preporuča se korištenje pomagala

za prihvat reaktivnog okretnog momenta, ako

je veći od 4 Nm kod strojeva s ravnim drškama,

ako je veći od 10 Nm kod strojeva s revorver

drškom.

Držite ruke dalje od rotirajuće stezne glave i

svrdla koje se okreće.

Unesite naredbu pokretanje ili zaustavljanje u

slučaju poremećaja opskrbe energijom.

Koristite isključivo sredstava za podmazivanje,

koje preporučuje proizvođač.

Moraju se nositi zaštitne naočale. Preporuča

se nošenje zaštitnih rukavica i zaštitne odjeće.

20 HR

Sigurnosne upute za pneumatske alate

Opasnosti zbog pokreta

koji se ponavljaju

Kod korištenja bušilice može operator kod izvo-

đenja radnih aktivnosti imati neugodne osje-

ćaje u šakama, rukama, ramenima, u vratu ili

drugim dijelovima tijela.

Kod izvođenja rada s ovim strojem zauzmite

udoban položaj, pazite na sigurno držanje i

izbjegavajte nepovoljne položaje ili takve, kod

kojih je teško držati ravnotežu. Opreator treba

za vrijeme dugog rada stalno mijenjati položaj

tijela, što može pomagati, da izbjegnete nela-

godu i umor.

Ako operator primjeti simptome kao npr. trajnu

mučninu, poteškoče, lupanje, bolove, trnce, utrnu-

lost, pečenje ili ukočenost, takvi znakovi se ne

smiju ignorirati. Operator treba konzultirati kva-

liﬁciranog liječnika.

Opasnosti zbog pribora

Isključite stroj od napajanja energije, prije

nego mijenjate alat stroja ili pribor.

Koristite isključivo veličinu i tip dijelova pribora

i potrošnog materijala kojeg preporučuje proi-

zvođač bušilice i rezača navoja, ne koristite

nikakve druge tipove ni veličinu pribora i po-

trošnog materijala.

Izbjegavajte za vrijeme i nakon korištenja di-

rektan kontakt s alatom stroja, jer se je ovaj

mogao zagrijati ili imati oštre uglove.

Opasnosti na radnom mjestu

Sklizanje, spoticanje i padovi su glavni uzroci

za ozljede na radnom mjestu. Pazite na površine,

koje zbog upotrebe stroja mogu postati klizave,

i zbog crijeva za zrak ili hidraulična crijeva uz-

rokovane opasnosti spoticanja.

Budite oprezni u nepoznatim sredinama. Može

biti sakrivenih opasnosti zbog električnog kabla

ili drugih komunalnih vodova.

Bušilica nije namijenjena za korištenje u atmos-

ferama u kojoj prijeti eksplozija i nije izoliran

protiv kontakta od električnog izvora energije.

Uvjerite se da nema električnih vodova, plino-

voda itd., koji bi se mogli oštetiti zbog korištenja

stroja i tako prouzročiti opasnosti.

Opasnosti zbog prašine i pare

Prašine i pare koja nastaju kod korištenja buši-

lice mogu uzrokovati zdravstvene štete (kao

npr. rak, urođene defekte, asmu i / ili dermati-

tis) neophodno je da se provede procjena ri-

zika u odnosu na opasnosti i da se sprovedu

odgovarajuće mjere zaštite.

U procjenu rizika kod korištenja stroja treba se

uključiti nastala prašina i eventualno moguće

vrtloženje prašine.

Bušilica ili rezač navoja se treba koristiti i odr-

žavati po ovdje navedenim uputama, kako bi

se stvaranje prašine i pare svelo na minimum.

Ispušni zrak se treba tako odvoditi, da se

vrtloženje prašine u jednoj okolini ispunjenom

prašinom svede na minimum.

Ako nastaje prašina ili para, mora biti glavana

zadaća, da se ove na mjestu ispuštanja kontro-

liraju.

Sva predviđena instalacija ili pribor stroja za

sakupljanje, usisavanje ili za suzbijanje leteće

prašine ili pare treba biti u skladu s uputama

proizvođača i biti pravilno instalirana i održa-

vana.

Potrošni materijali i strojni alati se trebaju

odabrati u skladu s ovim uputama, održavati i

zamijeniti, kako bi se izbjeglo nepotrebno ra-

zvijanje prašine i pare.

Koristite zaštitnu opremu za disanje, kao što

zhtjevaju propisi za zaštitu rada i zdravlja.

Opasnosti zbog buke

Djelovanje visoke razine buke može u slučaju

neadkvatne zaštite sluha dovesti do trajnog

oštećenja sluha, gubitka sluha i drugih problema,

Pagina se încarcă ...

Parkside 300098 Operation and Safety Notes

Acest manual este potrivit și pentru

Parkside 300098 Operation and Safety Notes

în alte limbi

Lucrări conexe

Alte documente