Samsung RSG5FUBP Manual de utilizare

English

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

To receive a more complete service,

please register your product at

www.samsung.com/register

Free Standing Appliance

This manual is made with 100% recycled paper.

02_ safety information

SAFETY INFORMATION

• Before operating the appliance, please

read this manual thoroughly and retain it

for your reference.

• Because these following operating

instructions cover various models, the

characteristics of your refrigerator may

differ slightly from those described in this

manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or

serious injury exists.

CAUTION

Indicates that a risk of personal injury or

material damage exists.

OTHER SYMBOLS USED

Represents something you must NOT do.

Represents something you must NOT

disassemble.

Represents something you must NOT

touch.

Represents something you must follow.

Indicates that you must disconnect the

power plug from the socket.

Represents a ground is needed to prevent

electric shock.

It is recommended that this symbol be

handled by service man.

These warning signs are here to prevent injury to

you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place

for future reference.

CE Notice

This product has been determined to be in

compliance with the Low Voltage Directive

(2006/95/EC), the Electromagnetic Compatibility

Directive (2004/108/EC) and the Eco-Design

Directive(2009/125/EC) implemented by Regulation

(EC) No 643/2009 of the European Union.

• This refrigerator must be properly installed and

located in accordance with the manual before it is

used.

• Use this appliance only for its intended purpose as

described in this instruction manual.

• We strongly recommend that any servicing be

performed by a qualiﬁ ed individual.

• R600a or R134a can be used as a refrigerant.

Check the compressor label on the rear of the

appliance and the rating label inside the fridge to

see which refrigerant is used for the refrigerator.

• In case of R600a refrigerant, this gas

is natural gas with high environmental

compatibility that is, however, also

combustible. When transporting and

installing the appliance, care should

be taken to ensure that no parts of the

refrigerating circuit are damaged.

• Refrigerant squirting out of the pipes could ignite

or cause an eye injury. If a leak is detected,

avoid any naked flames or potential sources of

ignition and air the room in which the appliance is

standing for several minutes.

• In order to avoid the creation of a ﬂ ammable

gas-air mixture if a leak in the refrigerating

circuit occurs, the size of the room in

which the appliance may be sited depends

on the amount of refrigerant used.

• Never start up an appliance showing any signs of

damage. If in doubt, consult your dealer.

• The room must be 1m3 in size for every 8g of

R600a refrigerant inside the appliance.

• The amount of refrigerant in your particular

appliance is shown on the identification plate

inside the appliance.

• Please dispose of the packaging material for this

product in an environmentally friendly manner.

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

• Children should be supervised to ensure that they

do not play with the appliance.

safety information

WARNING

safety information _03

SEVERE WARNING SIGNS

• Do not install the refrigerator in a damp

place or place where it may come in

contact with water.

- Deteriorated insulation of electrical parts may

cause an electric shock or ﬁ re.

• Do not place this refrigerator in direct sunlight or

expose to the heat from stoves, room heaters or

other appliance.

• Do not plug several appliances into the same

power socket. The refrigerator should always be

plugged into its own individual electrical which has

a voltage rating that matched the rating plate.

- This provides the best performance and also

prevents overloading house wiring circuits, which

could cause a ﬁ re hazard from overheated wires.

• Make sure that the power plug is not squashed or

damaged by the back of the refrigerator.

• Do not bend the power cord excessively or place

heavy articles on it.

- This constitutes a ﬁ re hazard.

• Have the power cord repaired or replaced

immediately by the manufacturer or its service

agent if power cord has become frayed or

damaged.

• Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

• If the power cord is damaged, have it replaced

immediately by the manufacturer or its service

agent.

• When moving the refrigerator, be careful not to roll

over or damage the power cord.

• Do not insert the power plug with wet hands.

• Unplug the refrigerator before cleaning and

making repairs.

• Do not use a wet or damp cloth when cleaning

the plug.

• Remove any foreign matter or dust from the power

plug pins.

- Otherwise there is a risk of ﬁ re.

• If the refrigerator is disconnected from the power

supply, you should wait for at least ten minutes

before plugging it back.

• If the wall socket is loose, do not insert the power

plug.

- There is a risk of electric shock or ﬁ re.

• The appliance must be positioned so that the plug

is accessible after installation.

• The refrigerator must be grounded.

- You must ground the refrigerator to

prevent any power leakages or electric

shocks caused by current leakage from

the refrigerator.

• Never use gas pipes, telephone lines or

other potential lightening rods as ground.

- Improper use of the ground plug can result in

electric shock.

• Do not dissemble or repair the refrigerator by

yourself.

- You run risk of causing a ﬁ re, malfunction and/or

personal injury.

• If you smell pharmaceutical or smoke, pull

out power plug immediately and contact your

Samsung electronics service center.

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

• Do not use mechanical devices or any other

means to accelerate the defrosting process, other

than those recommended by the manufacturer.

• Do not damage the refrigerant circuit.

• Do not place or use electrical appliance inside

the refrigerator/freezer, unless they are of a type

recommended by the manufacturer.

• Before changing the interior light, unplug the

appliance from the power supply.

• If you experience difficulty when changing the

light, contact your service center.

• The appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

• Children should be supervised to ensure that they

do not play with the appliance.

• Do not let children hang on the door. If not, a

serious injury may occur.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• If the refrigerator is not to be used for a long

period of time, pull out the power plug.

- Deterioration in the power cord insulation may

cause ﬁ re.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or material

damage.

CAUTION SIGNS

• This product is intended only for the

storage of food in a domestic environment.

• Manufacturer’s recommended storage times and

expiry dates of frozen foods should be adhered to.

Refer to relevant instructions

• Bottles should be stored tightly together so that

they do not fall out.

• Do not place carbonated or fizzy drinks in the

WARNING

CAUTION

04_ safety information

freezer compartment

• Do not overﬁ ll the refrigerator with food.

- When you open the door, an item may fall out and

cause personal injury or material damage.

• Do not put bottles or glass containers in the

freezer.

- When the contents freeze, the glass may break

and cause personal injury.

• Do not spray inﬂ ammable gas near the refrigerator.

- There is a risk of explosion or ﬁ re.

• Do not directly spray water inside or outside the

refrigerator.

- There is a risk of ﬁ re or electric shock.

• Do not store volatile or ﬂ ammable substances in

the refrigerator.

- The storage of benzene, thinner, alcohol, ether,

LP gas and other such products may cause

explosions.

• If you have a long vacation planned, it is advisable

to empty the appliance or use the vacation

function.

• Do not store pharmaceuticals products, scientiﬁ c

materials or temperature-sensitive products in the

refrigerator.

- Products that require strict temperature controls

must not be stored in the refrigerator.

• Do not put a container filled with water on the

refrigerator.

- If spilled, there is a risk of ﬁ re or electric shock.

CAUTION SIGNS FOR

CLEANING

• Never put ﬁ ngers or other objects into the

dispenser hole and ice chute.

- It may cause personal injury or material damage.

• Do not use a wet or damp cloth when cleaning

the plug, remove any foreign material or dust from

the power plug pins.

- Otherwise there is a risk of ﬁ re.

WARNING SIGNS FOR

DISPOSAL

• When disposing of this or other refrigerators,

remove the door/door seals, door latch so that

small children or animals cannot become trapped

inside.

• Leave the shelves in place so that children may

not easily climb inside.

• R600a or R134a is used as a refrigerant. Check

the compressor label on the rear of the appliance

or the rating label inside the fridge to see which

refrigerant is used for your refrigerator. When

this product contains ﬂ ammable gas (Refrigerant

R600a) contact your local authority in regard to

safe disposal of this product.

• Cyclopentane is used as a insulation blowing gas.

The gases in insulation material require special

disposal procedure. Please contact your local

authorities in regard to the environmentally safe

disposal of this product. Ensure that none of the

pipes on the back of the appliances are damaged

prior to disposal. The pipes shall be broke in the

open space.

In the event of a power failure, call the local

ofﬁ ce of your Electricity Company and ask how

long it is going to last.

Most power failures that are corrected in an hour or

two will not affect your refrigerator temperatures.

However, you should minimize the number of door

openings while the power is off.

But should the power failure last more than 24hours,

remove all frozen food.

For doors or lids ﬁ tted with locks and keys, the keys

be kept out of the reach of children and not in the

vicinity of the refrigerating appliance, in order to

prevent children from being locked inside.

ADDITIONAL TIPS FOR PROPER

USAGE

• Allow the appliance to stand for 2 hours

after installation.

• To get best performance of product,

- Do not place foods too closely in front of the vents

at the rear of the appliance as it can obstruct free

air circulation in the freezer compartment.

- Wrap the food up properly or place it in airtight

containers before put it into the fridge freezer

- Do not put any newly introduced food for freezing

near to already frozen food.

• There is no need to disconnect the refrigerator

from the power supply if you will be away for

less than three weeks. But, remove all the food if

you are going away for the three weeks or more.

Unplug the refrigerator and clean it, rinse and dry.

• The appliance might not operate consistently

(possibility of defrosting of contents or

temperature becoming too warm in the frozen

food compartment) when sited for an extended

period of time below the cold end of the range of

temperatures for which the refrigerating appliance

is designed.

• Do not store food which goes bad easily at low

temperature, such as bananas, melons.

• Place the ice tray at the originally provided

posistion by manufacturer in order to achieve

optimal ice-freezing.

CAUTION

safety information _05

• Your appliance is frost free, which means there is

no need to manually defrost your appliance, as

this will be carried out automatically.

• Temperature rising during the defrost can comply

with ISO requirement. But If you want to prevent

an undue rise in the temperature of the frozen

food while defrosting the appliance, please wrap

the frozen food in several layers of paper such as

newspaper.

• Any increase in temperature of frozen food during

defrosting can shorten its storage life.

• Contains fluorinated greenhouse gases covered

by the Kyoto Protocol.

• Foam blown with ﬂ uorinated greenhouse gases.

Foam blown additive:

Perﬂ uorohexane Global Warming

Potential (GWP) = 9000

SAVING ENERGY TIPS

- Install the appliance in a cool, dry room with

adequate ventilation. Ensure that it is not exposed

to direct sunlight and never put it near a direct

source of heat (radiator, for example).

- Never block any vents or grilles on the appliance.

- Allow warm food to cool down before placing it in

the appliance.

- Put frozen food in the refrigerator to thaw.

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

- Do not keep the door of the appliance open for

too long when putting food in or taking food out.

The shorter time for which the door is open, the

less ice will form in the freezer.

- Clean the rear of the refrigerator regularly. Dust

increases energy consumption.

- Do not set temperature colder than necessary.

- Ensure sufficient air exhaust at the refrigerator

base and at the back wall of the refrigerator.

Do not cover air vent openings.

- Allow clearance to the right, left, back and top

when installing. This will help reduce power

consumption and keep your energy bills lower.

contents

SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ……………………………………………………… 06

OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR …………………………………………… 13

TROUBLESHOOTING …………………………………………………………………………………………… 19

06_ setting up06_ setting up

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on the purchase of your Samsung

Side-By-Side Refrigerator. We hope you will enjoy

the many state-of-the-art features and efﬁ ciencies

that this new appliance has to offer.

Selecting the best location for the

refrigerator

• Select a location with easy access to the water

supply.

• Select a location without direct exposure to

sunlight.

• Select a location with level (or nearly level) ﬂ ooring.

• Select a location with enough space for the

refrigerator doors to open easily.

• Allow sufﬁ cient space to the right, left, back and

top for air circulation.

- If your refrigerator is not level, the internal cooling

system may not work correctly.

- Refer to drawing and dimensions below for overall

space required for use.

• Please ensure that appliance can be moved freely

in the event of maintenance & service.

When moving your refrigerator

To prevent ﬂ oor damage be sure the front levelling

legs are in the up position (above the ﬂ oor). Refer to

‘Levelling the refrigerator’ in the manual(at page 10).

To protect the ﬁ nish of the ﬂ ooring, place the

protection sheet such as packing carton under the

refrigerator.

When installing, servicing or cleaning behind

the refrigerator, be sure to pull the unit straight

out and push back in straight after ﬁ nishing.

USING THE ICE MAKER

To Remove the Ice Bucket

- Hold the handle as shown in

ﬁ gure1.

- Slightly pull up the bottom part.

- Take out the ice bucket slowly.

setting up your side-by-side

refrigerator

at least 6mmat least 6mm

CAUTION

Figure1Figure1

LegLeg

Screw DriverScrew Driver

setting up _07setting up _07

01 SETTING UP

Removing the Front Leg Cover

First, open both the freezer and refrigerator doors,

and then take off the front leg cover by turning the

three screws counter-clockwise.

Separating the Water Supply Line

from the Refrigerator (Optional)

1. Remove two water lines (gray one is for ice and

the other one is for water) by pressing the coupler

1

and pulling the water line

2

away.

Be careful that the water tube match same

color.

Reattaching the Water Supply Line

1. Water line must be fully inserted to the marked line

to prevent water leakage and water dripping of

water dispenser.

To Reﬁ t The Ice Bucket

- Assemble it in the reverse order

of disassembly.

- Push the bucket in ﬁ rmly until

you hear a clicking sound.

- When the bucket does not ﬁ t

into its place, turn the gear

handle on its back by 90

degrees and reinstall it again as

shown in ﬁ gure 2.

Normal Operation

- Any sounds you hear when

the ice maker dumps ice into

the bucket are part of normal

operation.

- Not dispensing ice for long

periods may cause ice clumps

in the ice bucket. Remove the

remaining ice and empty the

bucket.

- When ice does not come out,

check for any ice stuck in the

chute and remove it.

- The ﬁ rst batch of ice cubes may be small due

to air in the pipe after connection, any air will be

purged during normal use.

- When ICE OFF blinks on the display panel,

reinsert the bucket and/or make sure it’s

installed properly.

- When the door is open, the Ice and water

dispenser do not work.

- If you close the door hard, it may cause water

spilling over the ice maker.

- To prevent dropping the ice bucket, use both

hands when removing it.

- To prevent injury, be sure to clean up any ice or

water that may have dropped on the ﬂ oor.

- Do not let the children hang on the ice dispenser

or on the bucket. They may get hurt.

- Be sure not to put your hand or any object into the

ice chute. It may cause personal injury or damage

mechanical parts.

SETTING UP THE

REFRIGERATOR DOORS

If your entrance won’t allow the refrigerator to pass

easily through it, you can remove the doors.

CAUTION

Figure2Figure2

Ice ChuteIce Chute

1

2

LineLine

CouplerCoupler CouplerCoupler

08_ setting up08_ setting up

Be careful not to miss the parts of refrigerator.

3. Next, remove the door from the lower hinge

6

by

carefully lifting the door straight up

7

.

Be careful not to pinch the water tubing and

wire harness on the door.

4. Remove the lower hinge

8

from the bracket

9

by gently lifting the lower hinge upwards.

2. Insert the 2 clips in the install pack and check that

each clip holds the line ﬁ rmly.

Do not cut the water line. Gently separate it

from the coupler.

Removing the freezer door

A few things to mention ﬁ rst.

• Make sure that you lift the door straight up so the

hinges are not bent or broken.

• Be careful not to pinch the water tubing and wire

harness on the door.

• Place doors on a protected surface to prevent

scratching or damage.

1. With the Freezer door closed, remove the upper

hinge cover

1

using a screwdriver, and then

disconnect the wires by gently pulling them apart

2

.

2. Remove hinge screws

3

and the ground screw

4

by turning counter-clockwise, and take off the

upper hinge

5

. Be careful that the door does not

fall on you as you are removing it.

CouplerCoupler

clip Aclip A

(6.35mm)(6.35mm)

clip Aclip A

(6.35mm)(6.35mm)

1

2

- on some models- on some models

5

4

3

6

7

9

8

setting up _09setting up _09

01 SETTING UP

4. Remove the lower hinge

7

from the bracket

8

by gently

lifting the lower hinge upwards.

Reattaching the Fridge door

To reattach the fridge doors, assemble parts

in reverse order.

LEVELLING THE

REFRIGERATOR

Now that the doors are back on the refrigerator, you

want to make sure the refrigerator is level so that

you can make ﬁ nal adjustments. If the refrigerator

is not level, it will not be possible to get the doors

perfectly even.

The front of the refrigerator is also adjustable.

Before levelling the refrigerator,

remove the front leg cover

Open both the freezer and fridge doors, and then

take off the front leg cover by turning the three

screws counter-clockwise.

Reattaching the freezer doors

To reattach the freezer doors, assemble parts

in reverse order

Removing the Fridge Door

1. With the door closed, remove the upper hinge

cover

1

using a screwdriver.

2. Remove hinge screws

2

and the ground screw

3

by turning counter-clockwise, and take off the

upper hinge

4

. Be careful that the door does not

fall on you as you are removing it.

Be careful not to miss the parts of refrigerator.

3. Remove the door from the lower hinge

5

by lifting

the door straight up

6

.

4

3

2

1

5

6

8

7

10_ setting up10_ setting up

In the case of the process to correct the imbalance

is the same. Open the doors and adjust them, one

at a time, as follows:

1. Unscrew the nut

1

from the lower hinge until it

reaches the upper end of the bolt

2

.

When you release the nut

1

, make sure

that you use the Allen wrench provided

3

to loosen the bolt

2

in a counter-clockwise

direction. You should then be able to unscrew

the nut

1

with your ﬁ ngers.

2. Adjust the height difference between the doors by

turning the bolt

2

clockwise or counter

clockwise

.

When you turn clockwise

, the door will

move up.

3. After adjusting the doors, turn the nut

1

clockwise

until it reaches the lower end

of the bolt, then tighten the bolt again with the

wrench

3

to ﬁ x the nut in place

1

.

If you do not secure the nut ﬁ rmly, the bolt

may release.

When the Freezer door is lower than

the fridge

Insert a ﬂ at-blade screwdriver into a slot on the Leg,

turn it clockwise or counter clockwise to level the

freezer.

When the Freezer door is higher than

the fridge

Insert a ﬂ at-blade screwdriver into a slot on the Leg,

turn it clockwise or counter clockwise to level the

fridge.

Refer to the next section for the best way to

make very minor adjustments to the doors.

MAKING MINOR ADJUSTMENTS

TO THE DOORS

Remember, a levelling refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on levelling the

refrigerator.

Leg

Screw Driver

Leg

Screw Driver

Adjustment part

When the door of the freezer is When the door of the freezer is

higher than the fridgehigher than the fridge

Wrench

Bolt

Nut

1

2

3

setting up _11setting up _11

01 SETTING UP

4. After connecting the water supply to the water

ﬁ lter, turn your main water supply back on and

Dispense about 3L to clear and prime the water

ﬁ lter.

INSTALLING THE WATER

DISPENSER LINE

Connecting the water line to the

refrigerator

1. Remove the cap from water line on the unit and

insert compression nut to the water line on the

unit after disassembling from provided water line.

2. Connect both water line from the unit and water

line in the kit

3. Tighten the compression nut onto the

compression ﬁ tting. Be careful no gap between

two items.

4. Turn water on and check for any leakage.

CHECKING THE WATER

DISPENSER LINE

A water dispenser is just one of the helpful features

on your new Samsung refrigerator. To help promote

better health, the Samsung water ﬁ lter removes

unwanted particles from your water. However, it

does not sterilize or destroy microorganisms. You

will need to purchase a water purifying system to do

that.

In order for the icemaker to operate properly, water

pressure of 138 ~862 kPa is required. Under normal

conditions, a 170 cc paper cup can be ﬁ lled in 10

seconds.

If the refrigerator is installed in an area with low water

pressure (below 138 kPa), you can install a booster

pump to compensate for the low pressure.

Make sure the water storage tank inside the

refrigerator is properly ﬁ lled. To do this, press the

water dispenser lever until the water runs from the

water outlet.

Water Line installation Kits are included with

unit. You can ﬁ nd it in freezer(or fridge) drawer.

Parts for water line Installation

Connecting to the water supply line

1. First, shut off the main water supply line.

2. Locate the nearest cold, drinking water line.

3. Follow the Water Line Installation Instructions in

the installation kit.

1

Water line ﬁ xer Water line ﬁ xer

and screwsand screws

2

Pipe connectorPipe connector

3

Water lineWater line

4

ClipClip

5

Water FilterWater Filter

CAUTION

The water line must be connected to

the cold water pipe.

If it is connected to the hot water pipe,

it may cause the puriﬁ er to malfunction.

Close MainClose Main

Water pipeWater pipe

Close MainClose Main

Water pipeWater pipe

No gapNo gap

Remove Remove

capcap

Water LineWater Line

from unitfrom unit

Water LineWater Line

from Kitfrom Kit

No gapNo gap

Loosen aLoosen a

12_ setting up12_ setting up

Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the water line,

cut off 6.5mm of the plastic tubing to make sure you

get a snug, leak-free connection.

Before being used, the leakage in these

places should be examined

• Samsung Warranty does not cover WATER LINE

INSTALLATION.

• It’ll be done at customer’s charge unless the retail

price includes installation cost.

• Please contact Plumber or Authorized Installer for

the installation if needed.

• If Water leakage occurs due to improper

installation, Please contact installer.

Removing any residual matter inside

the water supply line after installing

ﬁ lter.

1. Turn ON the main water supply.

2. Press the Water button and

push the dispenser pad.

3. Run water through the

dispenser until the water

runs clear (approx. 3L). This

will clean the water supply

system and remove air from

the lines.

4. Additional ﬂ ushing may be

required in some households.

5. Open the refrigerator door

and make sure there are no

water leaks coming from the water ﬁ lter.

A newly installed water ﬁ lter cartridge may

cause water to brieﬂ y spurt from the water

dispenser. This is due to air getting into the

line. It should pose no problem to operation.

CAUTION

WaterWater

IceIce

operating _13operating _13

02 OPERATING

OPERATING THE

REFRIGERATOR

Using the Control Panel / Digital

Display

1

Power

Freeze

Button

Speeds up the time needed to freeze products in

the freezer. This can be helpful if you need to quickly

freeze items that spoil easily or if the temperature in

the freezer has warmed dramatically (For example,

if the door was left open). This Function must

be activated before putting large stuff in freezer

compartment at least 24 hours before.

2

Freezer

Button

Press the Freezer button to set the freezer to your

desired temperature. You can set the temperature

between -14°C and -25ºC.

3

Ice Off

Button

Press the Ice Off button to turn the ice making

function off.

When Ice Off blinks on the display panel, reinsert

the bucket and/or make sure it’s installed properly.

When you change the ﬁ lter, press and hold this

button for 3 seconds to reset the ﬁ lter schedule.

4

Lighting

Button

Press the Lighting button for the dispenser LED

lamp to stay on.

5

Fridge

Button

Press the Fridge button to set the fridge to your

desired temperature.

You can set temperature between 1°C ~ 7°C and

Power cool.

Power cool will be on the display after 1°C

6

Child Lock

Button

By pressing this button, all buttons will be locked.

The Ice Type button and the dispenser pad will not

work either.

To cancel this function, press this button again.

If you are going on vacation or business trip or you

do not need to use the refrigerator, press and hold

this button for 3 seconds. The temperature in the

fridge will be around 15°C and the freezer will work

normally.

7

Ice Type

Button

Press the Ice Type button to choose cubed or

crushed ice.

8

Water

Button

Press the Water button for water.

USING THE DIGITAL DISPLAY

“ Freezer Temp.” indicates the current Freezer

temperature.

“ Fridge Temp.” indicates the current Fridge

temperature.

When not in use the temperature display will turn off,

this is normal.

POWER FREEZE

This icon will light up when you activate the “Power

Freeze” feature. “Power Freeze” is great for times

when you need a lot of ice. When you have enough,

just press the button again to cancel the “Power

Freeze” mode.

When you use this function the energy

consumption of the refrigerator will increase.

Remember to turn it off when you don’t

need it and return the freezer to your original

temperature setting.

VACATION

This icon will light up when you activate the

“Vacation” feature.

If you are going on vacation or business trip or

you do not need to use the refrigerator, press and

hold the Child Lock button for 3 seconds. The

temperature in the fridge will be around 15°C and

the freezer will work normally. The refrigerator

section should be emptyed.

ALARM

This icon will light up all the time. The door alarm will

sound if any door is open for more than 2 minutes.

The beeping stops when you close the door. If

you need to turn off the Alarm function, press the

Lighting and Fridge buttons for 3 seconds at the

same time.

operating the SAMSUNG side-

by-side refrigerator

RSG5K/F/D/P/U*RSG5K/F/D/P/U*

RSG5S***RSG5S***

1

2

3

4

5

6

5

6

2

1

7 8

14_ operating14_ operating

CHILD LOCK

This icon will light up when you activate the Child

Lock function by pressing Child Lock button.

Press this button again to reactivate. Use this

function to prevent children from tampering with

temperature and ﬁ lter settings.

Canceling Exhibition Mode

In case of Exhibition Mode, It seems working

but doesn’t make cool air. To cancel this

mode, press the Power Freeze and Freezer

buttons at the same time for 8 seconds until

“Ding-dong” sounds.

CONTROLLING THE

TEMPERATURE

Basic Temperature of Freezer and

Fridge

The basic and recommended temperature of Freezer

and Fridge compartments are -20ºC/3ºC.

If the temperature of Freezer and Fridge

compartments are too high or low, adjust the

temperature manually.

Controlling the Freezer temperature

The freezer temperature can be set between -14°C

and -25ºC to suit your particular needs. Press

the Freezer button repeatedly until the desired

temperature is shown in the temperature display.

Keep in mind that foods like ice cream may melt at

-16ºC.

LIGHTING

This icon will light up when you activate the

“Lighting” feature. In this case, the dispenser light

(under the display) will be on constantly. If you would

like the dispenser light to come on only when using

the dispenser, turn the “Lighting” feature off.

POWER COOL

This icon will light up when you activate the “Power

Cool” feature.

For a quick fridge cool down, use “Power Cool”.

If you select “Power Cool”, the inside temperature

of the Fridge will decrease for about two and a half

hours.

FILTER INDICATOR

When the ﬁ lter indicator light changes to red, it is

time to change the ﬁ lter. Typically this happens about

every 6 months.

The ﬁ lter Indicator will be Blue when you initially

insert the water ﬁ lter.

The ﬁ lter Indicator will be purple when you have

used your water ﬁ lter for 5 months.

The ﬁ lter Indicator will be Red when you have used

your water ﬁ lter for 6 months.

After removing the old water ﬁ lter and installing a

new one (see page 19 for instructions on how to do

this), reset the indicator status light by pressing the

Ice off button for about 3 seconds.

CUBED ICE , CRUSHED ICE

Enjoy cubed or crushed ice by selecting your

preference from the digital control panel. The ice

type light indicates the type of ice that is currently

chosen.

WATER

This icon will light up when you activate the “Water”

feature.

ICE OFF

This icon will light up when you activate the “Ice Off”

feature. In this case, the ice will not be produced.

When Ice Off blinks on the display panel, reinsert

the bucket and/or make sure it’s installed properly.

CAUTION

Exhibition Exhibition

modemode

operating _15operating _15

02 OPERATING

Using the Water Dispenser

Press the Water button. Place your cup the water

outlet and push gently against the dispenser pad.

Make sure the glass is in line with the dispenser to

prevent the water from splashing out.

To get cooler water

- The dispensed water is cool, not

icy cold

- When you want colder water with

ice, dispense ice to your drink

glass ﬁ rst before ﬁ lling it with water

to prevent water from splashing

out.

Using the Ice Dispenser

Press the Ice Type button to select the type of ice

you want.

Place your cup the ice outlet and push gently

against the dispenser pad. Make sure the glass is

in line with the dispenser to prevent the ice from

bouncing out.

When Cubed Ice is selected after using the Crushed

Ice feature, a small amount of residual crushed ice

might be produced.

• Do not put your ﬁ ngers, hands or any

other unsuitable objects in the chute or

ice-maker bucket.

- It may result in personal injury or material damage.

• Use only the ice maker provided with the

refrigerator.

• The water supply to this

refrigerator must only be

installed/connected by a

suitably qualiﬁ ed person

and connect to a potable

water supply only.

• In order to operate the

ice maker properly, water

pressure of 138 ~ 862 kPa

is required.

The temperature display will move sequentially from

-14°C and -25ºC. When the display reaches -14ºC,

it will begin again at -25ºC.

Five seconds after the new temperature is set the

display will again show the actual current freezer

temperature. However, this number will change as

the Freezer adjusts to the new temperature.

Controlling the Fridge temperature

The refrigerator temperature can be set between

7ºC and 1ºC to suit your particular needs. Press

the Fridge button repeatedly until the desired

temperature is shown in the temperature display.

The temperature control process for the Fridge

works just like the Freezer process.

Press the Fridge button to set your desired

temperature. After a few seconds, the Fridge will

begin tracking towards the newly set temperature.

This will be reﬂ ected in the digital display.

The temperature of the freezer or the refrigerator

may rise from opening the doors too frequently, or

if a large amount of warm or hot food is placed in

either side.

This may cause the digital display to blink. Once

the freezer and refrigerator return to their normal set

temperatures the blinking will stop.

If the blinking continues, you may need to “reset” the

refrigerator. Try unplugging the appliance, wait about

10 minutes and then plug back in.

USING THE ICE AND COLD

WATER DISPENSER

When Ice Off blinks on the display panel, reinsert

the bucket and/or make sure it’s installed properly.

No Ice

Select this if you want to

turn the ice maker off.

PushPush

WARNING

Ice ChuteIce Chute

Ice BucketIce Bucket

Ice-Maker CoverIce-Maker Cover

16_ operating16_ operating

USING THE COOLSELECT

ZONE™ DRAWER (OPTIONAL)

The CoolSelect Zone™ Drawer is designed to make

your busy life just a little bit easier.

Soft Freeze

When “Soft Freeze” is selected on the CoolSelect

Zone™ Drawer, the temperature on the drawer

digital panel displays -5°C, regardless of the overall

temperature setting of the refrigerator.

This feature helps keep meat and ﬁ sh

fresh for longer.

Chill

When “Chill” is selected, the temperature

of the CoolSelect Zone™ Drawer is

kept at -1°C, regardless of the overall

temperature setting of the refrigerator.

This feature also helps keep meat or ﬁ sh

fresh for longer.

Thaw

When “Thaw” is selected, warm and cold

air is alternately blown into the CoolSelect Zone™

Drawer. Depending on the weight of the frozen food,

you can select a 4 hrs, 6 hrs, 10 hrs, and 12 hrs

thawing time.

When “Thaw” ends, food is in a half-frozen state,

making it easy to cut for cooking. In addition, when

“Thaw” ends, the CoolSelect Zone™ Drawer returns

to the original “Chill” condition. To cancel this

function mid-cycle, just press any button besides

Thaw.

Here are the approximate thawing times of meat

and ﬁ sh by weight (and based on a 25.4mm (1in.)

thickness). This chart represents the total weight of

food in the CoolSelect Zone™ Drawer.

THAW TIME WEIGHT

4hours 363g (0.8Ib)

6hours 590g (1.3Ib)

10hours 771g (1.7Ib)

12hours 1000g (2.2Ib)

• If you have a long vacation or business trip

and won’t use water or ice dispensers,

close the water valve.

- Otherwise, water leakage may occur.

• When you have not used the Ice maker for a while,

or you have opened the Freezer door frequently,

the Ice may stick together. If this has occurred,

empty the ice container or break up the ice with a

wood kitchen tool.

Do not use sharp items such as knives or forks.

• When the bucket is removed, there may still be

some residual ice in the ice maker that will be

produced.

For more space, you can store food with

Guard FRE-UPP instead

of the ice bucket (

1

).

If you remove the ice

bucket, ICE OFF will blink

on the display panel.

To get more space,

you can remove

freezer drawers and

locate the ‘SHELF

FRE-BOTTOM’ on the

bottom of the freezer,

since it does not affect

thermal and mechanical

characteristics.

A declared storage volume of frozen food

storage compartment is calculated with these

drawers removed.

The door guards in the freezer of this

model are the two star sections except the

top guard, so the temperature in two star

sections are slightly higher than other freezer

compartment.

CAUTION

1

GUARD FRE-UPPGUARD FRE-UPP

(Optional)(Optional)

GUARD FRE-BOTTOMGUARD FRE-BOTTOM

(Optional)(Optional)

operating _17operating _17

02 OPERATING

3. DRAWER

Remove the Drawer by pulling it

out and slightly lifting it up.

4. Ice Bucket (Freezer) (Optional)

Remove the Icemaker Bucket

by lifting up and pulling it out

slowly.

• Grip the handle as shown in

the ﬁ gure

• Lift the low part slightly

• Take the ice bucket out

slowly

5. Beverage Station (Fridge) (optional)

• Lift up the upper bin at the

top of the fridge and pull it

out.

• After pressing the cover

wrapped with both hands,

remove the beverage station

cover by pulling toward up.

Do not use excessive force when removing

the cover.

Otherwise, the cover may break and cause

injury.

Before removing any accessories, make sure

that no food is in the way.

When possible, remove the food altogether to

reduce the risk of accidents.

To get the best energy efﬁ ciency of this

product, please leave all selves, drawers

and baskets on their original position like as

illustration in page (16)

CLEANING THE REFRIGERATOR

Do not use Benzene, Thinner or Clorox™ for

cleaning.

They may damage the surface of the

appliance and can create a risk of ﬁ re.

Do not spray the refrigerator with water while

it is plugged in, as it may cause an electric

shock. Do not clean the refrigerator with

benzene, thinner or car detergent for risk of

ﬁ r e .

Quick Cool

You can use the “Quick Cool” operation with the

CoolSelect Zone™ Drawer to quickly cool 1~3

canned beverages in about an hour. When the

“Quick Cool” process ends, the CoolSelect Zone™

Drawer automatically returns to the previously set

temperature.

To cancel this operation, press the Quick Cool

button again and the CoolSelect Zone™ Drawer

returns to the previously set temperature.

Cool

When “Cool” is selected, the temperature in the

CoolSelect Zone™ Drawer will be the same as the

overall temperature setting of the refrigerator. The

drawer digital panel shows the same temperature

as that of the refrigerator display panel. Since the

“Cool” function mimics the refrigerator temperature,

you have extra general storage space.

Depending on the size and thickness of the

meat or ﬁ sh, thawing times may vary.

When “Thaw” is in operation, any items that

you do not want affected should be moved

out of the drawer.

REMOVING THE FREEZER/

FRIDGE ACCESSORIES

Cleaning and rearranging the interior of the freezer

is a snap.

1. Shelves (Freezer/Fridge)

Remove the shelf by pulling the

shelf out to the hole point as

shown at the right ﬁ gure. And

then remove it by turning and

lifting it up.

2. DOOR BIN

Remove the Door Bin by

holding the door bin with both

hands and then gently lift it up.

WARNING

CAUTION

18_ operating18_ operating

4. Once you have completed this process, hold the

Ice Off button simultaneously for 3 seconds to

reset the ﬁ lter schedule.

5. Lastly, run about 3L of water through water

dispenser and throw away. Make sure that water

ﬂ ows clearly again before drinking.

6. See installing the water ﬁ lter instructions page 11.

A newly installed water ﬁ lter cartridge may cause

water to brieﬂ y spurt from the water dispenser. This

is due to air getting into the line. It should pose no

problem to operation.

Ordering replacement ﬁ lters

To order more water ﬁ lter cartridges, contact your

authorized Samsung dealer.

USING THE DOORS

The refrigerator doors are equipped with a door

opening and closing feature that ensures that the

doors close all the way and are securely sealed.

After opening beyond a certain point, the door will

“catch” and remain open. When the door is ajar

ahead of the catch that allows it to stay open, it will

close automatically.

CHANGING THE INTERIOR

LIGHTS

Changing the LED Type Lighting

Do not disassemble or replace the LED type

Lighting.

To change the LED Type Lighting contact Samsung

service center or your authorized Samsung dealer.

CHANGING THE WATER FILTER

(OPTIONAL)

To reduce risk of water damage to your

property DO NOT use generic brands of water

ﬁ lers in your SAMSUNG Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTERS.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from use of a

generic water ﬁ lter.

SAMSUNG Refrigerators are designed to work

ONLY WITH SAMSUNG Water Filter.

The “Filter Indicator” light lets you know when it is

time to change your water ﬁ lter cartridge.

To give you preparation time to get a new ﬁ lter, the

red light will come on just before the capacity of the

current ﬁ lter runs out. Changing the ﬁ lter on time

provides you with the freshest, cleanest water from

your fridge.

1. Remove the water ﬁ lter from the box and

put a month indicator sticker on the ﬁ lter

as shown. Place a sticker on the ﬁ lter

that dates six months in the future. For

example, if you are replacing the water

ﬁ lter in March, put the “SEP” (September)

sticker on the ﬁ lter to remind you to

replace in September. Normal ﬁ lter life is

about every 6 months.

2. Remove the new ﬁ lter’s protective cap and remove

the old ﬁ lter.

3. Position and insert the new ﬁ lter into the ﬁ lter

housing. Slowly turn the water ﬁ lter clockwise to

align with the printing mark on the cover, locking

the ﬁ lter in position. Make sure to align the water

ﬁ lter label mark with the center of cover ﬁ lter

printing as illustrated. Remember, do not over-

tighten.

CAUTION

WARNING

123

Turn until the Turn until the

label aligned.label aligned.

Cover ﬁ lterCover ﬁ lter

StickerSticker

(month indicator)(month indicator)

troubleshooting _19troubleshooting _19

03 TROUBLESHOOTING

troubleshooting

PROBLEM SOLUTION

The refrigerator does not

work at all or it does not

chill sufﬁ ciently.

• Check that the power plug is properly connected.

• Is the temperature control on the display panel set to the correct

temperature? Try setting it to a lower temperature.

• Is the refrigerator in direct sunlight or located too near a heat source?

• Is the back of the refrigerator too close to the wall and therefore keeping

air from circulating?

The food in the fridge is

frozen.

• Is the temperature control on the display panel set to the correct

temperature? Try setting it to a warmer temperature.

• Is the temperature in the room very low?

• Did you store the food with a high water content in the coldest part of

the fridge? Try moving those items into the body of the fridge instead of

keeping them in the CoolSelect Zone™ drawer.

You hear unusual noises

or sounds.

• Check that the refrigerator is level and stable.

• Is the back of the refrigerator too close to the wall and therefore keeping

air from circulating?

• Was anything dropped behind or under the refrigerator?

• A “ticking” sound is heard from inside the refrigerator. This is normal and

occurs because various accessories are contracting or expanding in

relation to the temperature of the refrigerator interior.

The front corners of

the appliance are hot

and condensation is

occurring.

• Some heat is normal as anti-condensators are installed in the front

corners of the refrigerator to prevent condensation.

• Is the refrigerator door ajar? Condensation can occur when you leave the

door open for a long time.

Ice is not dispensing. • Did you wait for 12 hours after installation of the water supply line before

making ice?

• Is the water line connected and the shut-off valve open?

• Did you manually stop the ice making function? Make sure Ice Type is set

to Cubed or Crushed.

• Is there any ice blocked within the ice maker bucket?

• Is the freezer temperature too warm? Try setting the freezer temperature

lower.

You can hear water

bubbling in the

refrigerator.

• This is normal. The bubbling comes from the refrigerant coolant liquid

circulating through the refrigerator.

There is a bad smell in the

refrigerator.

• Has a food item spoiled?

• Make sure that strong smelling food (for example, ﬁ sh) is wrapped so that

it is airtight.

• Clean out your freezer periodically and throw away any spoiled or

suspect food.

Frost forms on the walls

of the freezer.

• Is the air vent blocked? Remove any obstructions so air can circulate

freely.

• Allow sufﬁ cient space between the foods stored for efﬁ cient air

circulation.

• Is the freezer door closed properly?

Water dispenser is not

functioning.

• Is the water line connected and the shut-off valve open?

• Has the water supply line tubing been crushed or kinked?

Make sure the tubing is free and clear of any obstruction.

• Is the water tank frozen because the refrigerator temperature is too low?

Try selecting a warmer setting on the main display panel.

English

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories

(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their

working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,

please separate these items from other types of waste and recycle them responsibly to promote the sustainable

reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government

ofﬁ ce, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This

product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Ambient Room Temperature Limits

This fridge/freezer is designed to operate in ambient temperatures speciﬁ ed by its temperature

class marked on the rating plate.

NOTE: Internal temperatures may be affected by such factors as the location of the fridge/

freezer, ambient temperature and the frequency with which you open the door. Adjust

the temperature as required to compensate for these factors.

Class Symbol Ambient Temperature range(°C)

Extended Temperate SN +10 to +32

Temperate N +16 to +32

Subtropical ST +16 to +38

Tropical T +16 to +43

Pagina se încarcă ...

Samsung RSG5FUBP Manual de utilizare

Samsung RSG5FUBP Manual de utilizare

Lucrări conexe

Alte documente