Samsung RSH7UNBP Manual de utilizare

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

To receive a more complete service,

please register your product at

www.samsung.com/register

English

Free Standing Appliance

This manual is made with 100% recycled paper.

2_ safety information

safety information

SAFETY INFORMATION

• Before operating the appliance, please read

this manual thoroughly and retain it at a

safe place near the appliance for your future

reference.

• Use this appliance only for its intended

purpose as described in this instruction

manual. This appliance is not intended for use

by persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

• Warnings and Important Safety Instructions

in this manual do not cover all possible

conditions and situations that may occur. It

is your responsibility to use common sense,

caution, and care when installing, maintaining,

and operating your appliance.

• Because these following operating instructions

cover various models, the characteristics of

your refrigerator may differ slightly from those

described in this manual and not all warning

signs may be applicable. If you have any

questions or concerns, contact your nearest

service center or ﬁ nd help and information

online at www.samsung.com.

Important safety symbols and

precautions :

WARNING

Hazards or unsafe practices that

may result in severe personal

injury or death.

CAUTION

Hazards or unsafe practices that

may result in minor personal

injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the

wall socket.

Make sure the machine is grounded

to prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

CE Notice

This product has been determined to be in

compliance with the Low Voltage Directive

(2006/95/EC), the Electromagnetic Compatibility

Directive (2004/108/EC) and the Eco-Design

Directive(2009/125/EC) implemented by Regulation

(EC) No 643/2009 of the European Union.

SEVERE WARNING SIGNS

FOR TRANSPORTATION

AND SITE

• When transporting and installing the

appliance, care should be taken to ensure

that no parts of the refrigerating circuit are

damaged.

- Refrigerant leaking from the pipe work could

ignite or cause an eye injury. If a leak is detected,

avoid any naked ﬂ ames or potential sources of

ignition and air the room in which the appliance

is standing for several minutes.

• In order to avoid the creation of a ﬂ ammable

gas-air mixture if a leak in the refrigerating

circuit occurs, the size of the room in which the

appliance may be sited depends on the amount

of refrigerant used.

• Never start up an appliance showing any signs

of damage. If in doubt, consult your dealer. The

room where the refrigerator will be sited must

be 1m³ in size for every 8g of R600a refrigerant

inside the appliance. The amount of refrigerant

in your particular appliance is shown on the

identiﬁ cation plate inside the appliance.

WARNING

safety information _3

SEVERE WARNING SIGNS

FOR INSTALLATION

•

Do not install the refrigerator in a damp place

or place where it may come in contact with

water.

- Deteriorated insulation of electrical parts may

cause an electric shock or ﬁ re.

• Do not place this refrigerator in direct sunlight or

expose to the heat from stoves, room heaters or

other appliance.

• Do not plug several appliances into the same

multiple power board.

The refrigerator should always be plugged into

its own individual electrical which has a voltage

rating that matched the rating plate.

- This provides the best performance and also

prevents overloading house wiring circuits, which

could cause a ﬁ re hazard from overheated wires.

• If the wall socket is loose, do not insert the

power plug.

- There is a risk of electric shock of ﬁ re.

• Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

• Do not bend the power cord excessively or

place heavy articles on it.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause

an explosion or ﬁ re.

• This refrigerator must be properly installed

and located in accordance with the manual

before it is used.

• Connect the power plug in proper position with

the cord hanging down.

- If you connect the power plug upside down,

wire can get cut off and cause ﬁ re or electric

shock.

• Make sure that the power plug is not squashed

or damaged by the back of the refrigerator.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a ﬁ re hazard.

• The appliance must be positioned so that the

plug is accessible after installation.

• The refrigerator must be grounded.

-

You must ground the refrigerator to prevent

any power leakages or electric shocks caused

by current leakage from the refrigerator.

• Never use gas pipes, telephone lines or other

potential lightening rods as ground.

- Improper use of the ground plug can result in

electric shock.

• If the power cord is damaged, have it

replaced immediately by the manufacturer

or its service agent.

• The fuse on the refrigerator must be changed by

a qualiﬁ ed technician or service company.

- Failing to do so may result in electric shock or

personal injury.

CAUTION SIGNS FOR

INSTALLATION

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

• Allow the appliance to stand for 2 hours after

installation.

SEVERE WARNING SIGNS

FOR USING

• Do not insert the power plug with wet

hands.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or

material damage.

• Do not put items ﬁ lled with water on the

refrigerator.

- If spilled, there is a risk of ﬁ re or electric shock.

• Do not let children hang on the door.

- Failure to do so may cause serious personal

injury.

• Do not leave the doors of the refrigerator open

while the refrigerator is unattended and do not

let children enter inside of the refrigerator.

- There is a risk of children entrapment and

serious personal injury because of low

temperature.

• Never put ﬁ ngers or other objects into the

dispenser hole.

- Failure to do so may cause personal injury or

material damage.

• Do not store volatile or ﬂ ammable substances

such as benzene, thinner, alcohol, ether or LP

gas in the refrigerator.

- The storage of any of such products may

cause explosions.

WARNING

CAUTION

WARNING

4_ safety information

• Do not store low temperature-sensitive

pharmaceuticals products, scientiﬁ c

materials or other low temperature-

sensitive products in the refrigerator.

- Products that require strict temperature controls

must not be stored in the refrigerator.

• Do not place or use electrical appliance inside

the refrigerator, unless they are of a type

recommended by the manufacturer.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in the

refrigerator for removing bad odors.

- This may result in electric shock or ﬁ re.

•

Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Do not use mechanical devices or any other

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

• Do not damage the refrigerant circuit.

• This product is intended only for the

storage of food in a domestic environment.

• Bottles should be stored tightly together so that

they do not fall out.

• If a gas leak is detected, avoid any naked ﬂ ames

or potential sources of ignition and air the room

in which the appliance is standing for several

minutes.

• Use only the LED Lamps provided by

manufacturer or service agents.

• Children should be supervised to ensure that

they do not play with and/or climb into the

appliance.

• Do not disassemble or repair the

refrigerator by yourself.

- You run risk of causing a ﬁ re, malfunction and/

or personal injury. In case of malfunction, please

contact your service agents.

• If the appliance generates a strange noise,

a burning or smell or smoke, unplug the

power plug immediately and contact your nearest

service center.

- Failing to do so may result in electric or ﬁ re

hazards. Keep ventilation opening in the

appliance enclosure or mounting structure clear

of obstruction.

• If you experience difﬁ culty when changing the

light, contact service agents.

• If the products equipped with LED Lamp, do

not disassemble Lamp Cover and LED Lamp by

yourself.

- Please contact your service agents.

• If any dust or water is in refrigerator, pull

out power plug and contact your Samsung

Electronics service center.

- There is a risk of ﬁ re.

CAUTION SIGNS FOR

USING

• To get best performance of product,

- Do not place foods too closely in front of

the vents at the rear of the appliance as it can

obstruct free air circulation in the refrigerator

compartment.

-

Wrap the food up properly or place it in airtight

containers before put it into the refrigerator.

• Do not place carbonated or ﬁ zzy drinks in the

freezer compartment. Do not put bottles or glass

containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury and property damage.

• Do not change the functionality of or modify the

refrigerator.

- Changes or modiﬁ cations may result in personal

injury and/or property damage. Any changes or

modiﬁ cations performed by a 3rd party on this

completed appliance is neither covered under

Samsung warranty service, nor is Samsung

responsible for safety issues and damages that

result from 3rd party modiﬁ cations.

• Do not block air holes.

-

If the air holes are blocked, especially with a plastic

bag, the refrigerator can be over cooled. If this

cooling period lasts too long, the water ﬁ lter may

break and cause water leakage.

- Do not put any newly introduced food for

freezing near to already food.

• Please observe maximum storage times and

expiry dates of frozen goods.

• Fill water tank, ice tray, water cubes only with

potable water.

• Use only the ice maker provided with the

refrigerator.

• The water supply to this refrigerator must only

be installed/connected by a suitably qualiﬁ ed

person and connect to a potable water supply

only.

•

In order to operate the ice maker properly, water

pressure of 138 ~ 862kpa(1.4~8.8kgf/cm

3

) is

required.

CAUTION

safety information _5

CAUTION SIGNS

FOR CLEANING AND

MAINTENANCE

• Do not directly spray water inside or

outside the refrigerator.

- There is a risk of ﬁ re or electric shock.

• Do not spray inﬂ ammable gas near the

refrigerator.

- There is a risk of explosion or ﬁ re.

• Do not spray cleaning products directly on the

display.

- Printed letters on the display may come off.

•

Remove any foreign matter or dust from the

power plug pins. But do not use a wet or damp

cloth when cleaning the plug, remove any foreign

material or dust from the power plug pins.

- Otherwise there is a risk of ﬁ re or electric shock.

• Never put ﬁ ngers or other objects into the

dispenser hole and ice chute.

- It may cause personal injury or material damage.

• Unplug the refrigerator before cleaning and

performing maintenance.

SEVERE WARNING SIGNS

FOR DISPOSAL

• Ensure that none of the pipes on the back

of the appliance are damaged prior to

disposal.

• R600a or R134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

refrigerator to see which refrigerant is used for

your refrigerator. When this product contains

ﬂ ammable gas (Refrigerant R600a), contact your

local authority in regard to safe disposal of this

product. Cyclopentane is used as a insulation

blowing gas. The gases in insulation material

require special disposal procedure. Please

contact your local authorities in regard to the

environmentally safe disposal of this product.

Ensure that none of the pipes on the back of the

appliances are damaged prior to disposal. The

pipes shall be broke in the open space.

• If the appliance contains iso-butane refrigerant

(R600a), a natural gas with high environmental

compatibility that is, however, also combustible.

When transporting and installing the appliance,

care should be taken to ensure that no parts of

the refrigerating circuit are damaged.

• When disposing of this product or other

refrigerators, remove the door/door seals, door

latch so that small children or animals cannot

become trapped inside. Leave the shelves in

place so that children may not easily climb

inside. Children should be supervised to ensure

that they do not play with the old appliance.

•

Please dispose of the packaging material for this

product in an environmentally friendly manner.

ADDITIONAL TIPS FOR PROPER

USAGE

• In the event of a power failure, call the local ofﬁ ce

of your Electricity Company and ask how long it is

going to last.

- Most power failures that are corrected within

an hour or two will not affect your refrigerator

temperatures. However, you should minimize the

number of door openings while the power is off.

- Should the power failure last more than 24 hours,

remove all frozen food.

• If keys are provided with the refrigerator, the

keys should be kept out of the reach of children

and not in vicinity of the appliance.

• The appliance might not operate consistently

(possibility of temperature becoming too warm

in refrigerator) when sited for an extended period

of time below the cold end of the range of

temperature for which the refrigerating appliance

is designed.

• Do not store food which spoils easily at low

temperature, such as bananas, melons.

• Your appliance is frost free, which means there

is no need to manually defrost your appliance,

as this will be carried out automatically.

• Temperature rising during the defrost can

comply with ISO requirement. But if you want

to prevent an undue rise in the temperature of

the frozen food while defrosting the appliance,

please wrap the frozen food in several layers of

newspaper.

• Any increase in temperature of frozen food

during defrosting can shorten its storage life.

CAUTION

WARNING

6_ safety information

contents

SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ···································7

OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR ····················16

TROUBLESHOOTING ····················································································· 22

Saving Energy Tips

- Install the appliance in a cool, dry room with

adequate ventilation.

Ensure that it is not exposed to direct sunlight and

never put it near a direct source of heat (radiator, for

example).

- Never block any vents or grilles on the appliance.

- Allow warm food to cool down before placing it in

the appliance.

- Put frozen food in the refrigerator to thaw.

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

- Do not keep the door of the appliance open for too

long when putting food in or taking food out.

The shorter time for which the door is open, the less

ice will form in the freezer.

- Clean the rear of the refrigerator regularly. Dust

increases energy consumption.

- Do not set temperature colder than necessary.

- Ensure sufﬁ cient air exhaust at the refrigerator base

and at the back wall of the refrigerator.

Do not cover air vent openings.

- Allow clearance to the right, left, back and top when

installing.

This will help reduce power consumption and keep

your energy bills lower.

setting up _7

01 SETTING UP

CAUTION

setting up your side-by-side

refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on the purchase of your Samsung

Side-By-Side Refrigerator. We hope you will enjoy the

many state-of-the-art features and efﬁ ciencies that

this new appliance has to offer.

Selecting the best location for the

refrigerator

• Select a location with easy access to the water

supply.

• Select a location without direct exposure to

sunlight.

• Select a location with level (or nearly level) ﬂ ooring.

• Select a location with enough space for the

refrigerator doors to open easily.

• Overall space required in use. Refer to drawing and

dimension as below.

• Please ensure that appliance can be moved freely

in the event of maintenance & service.

When moving your refrigerator

To prevent ﬂ oor damage be sure the front levelling

legs are in the up position (above the ﬂ oor). Refer to

‘Levelling the refrigerator’ in the manual (at page 11).

To protect the ﬁ nish of the ﬂ ooring, place the

protection sheet such as packing carton under the

refrigerator.

When installing, servicing or cleaning

behind the refrigerator, be sure to pull the

unit straight out and push back in straight

after ﬁ nishing.

Leg

Screw Driver

at least 50mm

25mm

50

8_ setting up

REMOVING THE REFRIGERATOR

DOORS

If your entrance won’t allow the refrigerator to pass

easily through it, you can remove the doors.

1. Removing the Front Leg Cover

First, open both the freezer and refrigerator doors,

and then take off the front leg cover by removing the

three screws counter-clockwise.

Separating the Water Supply Line from

the Refrigerator

1. Remove the water line by pressing the coupler

1

and pulling the water line

2

away.

2. Removing the freezer door

A few things to mention ﬁ rst.

• Make sure that you lift the door straight up so the

hinges are not bent or broken.

• Be careful not to pinch the water tubing and wire

harness on the door.

• Place doors on a protected surface to prevent

scratching or damage.

1. With the Freezer door closed, remove the upper

hinge cover

1

using a screwdriver, and then

disconnect the wires by gently pulling them apart

2

.

2. Remove hinge screws

3

and the ground screw

4

by turning counter-clockwise, and take off the

upper hinge

5

. Be careful that the door does not

fall on you as you are removing it

3. Next, remove the door from the lower hinge

6

by

carefully lifting the door straight up

7

.

Be careful not to pinch the water tubing and

wire harness on the door.

4. Remove the lower hinge

8

from the bracket

9

by gently lifting the lower hinge upwards.

2

1

3

4

5

7

6

1

2

Be careful

that the

water tube match

same colour.

setting up _9

01 SETTING UP

Removing the Fridge Door

1. With the door closed, remove the upper hinge

cover

1

using a screwdriver.

2. Remove hinge screws

2

and the ground screw

3

by turning counter-clockwise, and take off the

upper hinge

4

. Be careful that the door does not

fall on you as you are removing it

3. Remove the door from the lower hinge

5

by

lifting the door straight up

6

.

4. Remove the lower hinge

7

from the bracket

8

by gently lifting the lower hinge upwards.

REATTACHING THE

REFRIGERATOR DOORS

Once you have safely placed your refrigerator where

you plan for it to stay, it is time to put the doors back

on.

Reattaching the Freezer Door

1. Replace the freezer door by inserting the water

line

1

back into the lower corner of the door and

then into the hole on the lower hinge

2

.

Gently pull the water line back down so that it runs

straight, with no kinks or bends.

2. Insert the upper hinge shaft

3

into the hole on

the corner of the freezer door

4

.

Make sure the hinge is level between the upper

hinge hole

5

and the hole of the cabinet

6

and

reattach the hinge screws

7

and ground screw

8

by turning in a clockwise direction.

Reconnect the wires.

3. Place the front part of the upper hinge cover

9

on the front of the upper hinge

10

and reattach

with the screw.

4

2

3

1

10

9

4

5

6

7

8

3

1

2

10_ setting up

Reattaching the Fridge Door

1. Insert the lower hinge

1

back into the lower

hinge bracket

2

.

2. Fit the hole in the corner of the fridge door

3

over the lower hinge

4

.

3. Insert the upper hinge shaft

5

into the hole

on the hinge

6

. Make sure the hinge is level

between the upper hinge hole

7

and the hole on

the top of the cabinet

8

. Then, reattach hinge

screws

9

and the ground screw

10

by turning it

in a clock wise direction.

4. Place the front part of the upper hinge cover

11

on the front of the upper hinge

12

and reattach it

with the screw.

Reattaching the Water Supply Line

1. Insert the water line

1

into the coupler

2

.

Reattaching the Water Supply Line

1. Water line must be fully inserted to the marked line

to prevent water leakage and water dripping from

the water dispenser.

2. Insert the 2 clips in the install pack and check that

each clip holds the line ﬁ rmly.

Do not cut the water line. Gently separate it

from the coupler.

Reattaching the Front Leg Cover

Before attaching the cover, check water

connector for leakage.

Replace the front leg cover by turning the three

screws clockwise, as shown in the ﬁ gure.

1

2

3

4

12

11

1

2

Line

Coupler

clip A

(6.35mm)

clip A

(6.35mm)

Coupler

WHITE

GRAY

setting up _11

01 SETTING UP

LEVELLING THE REFRIGERATOR

Now that the doors are back on the refrigerator, you

will want to make sure the refrigerator is level so you

can then make ﬁ nal adjustments. If the refrigerator

is not level, it will not be possible to get the doors

perfectly even.

The front of the refrigerator is also adjustable.

When the Freezer door is lower than

the fridge

Insert a ﬂ at-blade screwdriver into a notch on the

Leg, turn it clockwise or counter clockwise to level

the freezer.

When the Freezer door is higher than

the fridge

Insert a ﬂ at-blade screwdriver into a notch on the

Leg, turn it clockwise or counter clockwise to level

the fridge.

Refer to the next section for the best way to

make very minor adjustments to the doors.

MAKING MINOR ADJUSTMENTS

TO THE DOORS

Remember, a level refrigerator is necessary for getting

the doors perfectly even. If you need help, review the

previous section on levelling the refrigerator.

In the process for adjusting both the doors is the

same. Open the doors and adjust them, one at a

time, as follows :

1. Unscrew the

nut

1

from the

lower hinge until

it reaches the

upper end of the

bolt

2

.

When you release the nut

1

, make sure that

you use the Allen wrench provided

3

to loosen

the bolt

2

in a counter-clockwise direction.

You should then be able to unscrew the nut

1

with your ﬁ ngers.

2. Adjust the

height difference

between the

doors by turning

the bolt

2

clockwise

or counter clockwise

.

When you turn clockwise

, the door will

move up.

3. After adjusting

the doors, turn

the nut

1

clockwise

until it reaches

the lower end

of the bolt, then tighten the bolt again with the

wrench

3

to ﬁ x the nut in place

1

.

If you do not secure the nut ﬁ rmly, the bolt may

release.

Leg

Screw Driver

Leg

Adjustment

part

When the door of the freezer

is higher than the fridge

3

2

1

Wrench

Bolt

Nut

3

2

Wrench

Bolt

3

2

1

Wrench

Bolt

Nut

12_ setting up

CHECKING THE WATER

DISPENSER LINE (OPTIONAL)

A water dispenser is just one of the helpful features

on your new Samsung refrigerator. To help promote

better health, the Samsung water ﬁ lter removes

unwanted particles from your water. However, it

does not sterilize or destroy microorganisms. You

will need to purchase a water purifying system to do

that. In order for the icemaker to operate properly,

water pressure of 138 ~862 Kpa is required. Under

normal conditions, a 170 cc paper cup can be ﬁ lled

in 10 seconds. If the refrigerator is installed in an area

with low water pressure (below 138 Kpa), you can

install a booster pump to compensate for the low

pressure. Make sure the water storage tank inside

the refrigerator is properly ﬁ lled. To do this, press the

water dispenser lever until the water runs from the

water outlet.

Water Line installation Kits are included. You can

ﬁ nd it in one of the freezer drawers.

USING THE ICE MAKER (OPTIONAL)

To Remove the Ice Bucket

-

Hold the handle as shown in ﬁ gure1.

-

Slightly pull up the bottom part.

-

Take out the ice bucket slowly.

To Reﬁ t The Ice Bucket

- Assemble it in the reverse

order of disassembly.

- Push the bucket in ﬁ rmly until

you hear a clicking sound.

- When the bucket does not ﬁ t

into its place, turn the gear

handle on its back by 90

degrees and reinstall it again

as shown in ﬁ gure 2.

Normal Operation

- Any sounds you hear when

the ice maker dumps ice into

the bucket are part of normal

operation.

- Not dispensing ice for long

periods may cause ice

clumps in the ice bucket.

Remove the remaining ice

and empty the bucket.

- When ice does not come

out, Check for any ice stuck

in the chute and remove it.

-

The ﬁ rst batch of ice cubes may

be small due to air in the pipe

after connection, any air will be

purged during normal use.

- When ICE OFF blinks on the display panel,

reinsert the bucket and/or make sure it’s

installed properly.

- When the door is open, the Ice and water

dispenser do not work.

- If you close the door hard, it may cause

water spilling over the ice maker.

- To prevent dropping the ice bucket, use

both hands when removing it.

- To prevent injury, be sure to clean up any

ice or water that may have dropped on

the ﬂ oor.

-

Do not let children hang on the ice dispenser

or on the bucket.

They may get hurt.

- Be sure not to put your hand or any object

into the ice chute.

It may cause personal injury or damage

mechanical parts.

INSTALLING THE WATER

DISPENSER LINE

For Interior model

Parts for water line Installation

Connecting to the water supply line

1. ﬁ rst, shut off the main water supply line.

2. locate the nearest cold, drinking water line.

3. follow the Water line Installation Instructions in the

installation kit.

Figure2

Ice Chute

Figure1

CAUTION

The water line must be connected

to the cold water pipe. If it is connected

to the hot water pipe, it may cause the

puriﬁ er to malfunction.

1

Water line ﬁ xer and screws

2

Pipe connector

3

Water line

4

Clip

5

Water Filter

setting up _13

01 SETTING UP

4. After connecting the water supply to the water

ﬁ lter, turn your main water supply back on and

dispense about 1l to clear and prime the water

ﬁ lter.

Connecting the water line to the

refrigerator

1. Remove the dust cap from the water line on the

rear of the unit and ﬁ t a compression nut from the

install kit.

2. Remove the water pipe from the install kit and ﬁ t a

compression nut to one end.

3. Join the two pipes together using the compression

joint from the install kit ensuring that the joint is

water tight.

4. Join the other end of the install pipe to the main

water supply and turn on the water to check for

leaks.

Only connect the water line to a drinkable water

source.

If you have to repair or disassemble the water

line, cut off 6.5mm of the plastic tubing to

make sure you get a snug, leak-free connection.

Before being used, the leakage in

these places should be examined

• Samsung Warranty does not cover WATER LINE

INSTALLATION.

• The cost of connection to a water supply is at the

customer expense, unless included in the delivery

charge (refer to the delivery agreement with the

seller)

• Please contact Plumber or Authorised Installer for

the installation if needed.

• If Water leakage occurs due to improper

installation, Please contact installer.

INSTALLING THE WATER

DISPENSER LINE

For Exterior model

Parts for water line Installation

Connecting to the water supply line

Connect the water pipe with coupler and tap.

1. Close the main water tap.

2. Connect coupler “A” to the tap.

Close Main

Water pipe

Close Main

Water pipe

NO GAP

Water line ﬁ xer and screws

Pipe connector

Water line

Puriﬁ er lock-clip

Puriﬁ er

Remove

cap

Water Line

from unit

Water Line

from Kit

No gap

Loosen a

CAUTION

The water line must be connected to the cold

water pipe. If it is connected to the hot water

pipe, it may cause the puriﬁ er to malfunction.

14_ setting up

select the location where the puriﬁ er is to

install. (Model with the puriﬁ er)

- If you wish to reassemble the water inlet and outlet

sides of the puriﬁ er during puriﬁ er installation, see

the reference illustration.

- Cut the water line attached to the puriﬁ er to the

appropriate place after measuring the distance

between the puriﬁ er and the cold water tap.

Replacement Instructions

1. Shut off water supply.

2. Note the Flow direction on the ﬁ lter.

3. Insert water supply tube into the inlet side of the

ﬁ lter until the tube stop.

4. After inserting tube, put together the clip strongly.

The Clip ﬁ x the tube.

5. Turn on the water and check for leaks. If leaks

occur, repeat step 1,2,3,4. If leaks persist,

discontinue use and call your supporting dealer.

6. Flush ﬁ lter for 5 minutes before use.

Remove any residual matter inside the

puriﬁ er. (Model with the puriﬁ er)

- Open the main water tap to check whether water

is running through the water tube on the water inlet

side of the puriﬁ er.

- If water does not come out through the line, check

whether the tap is open.

- Leave the tap open until clean water is running

out and any residual matter that built up during

manufacturing has been removed.

Attach the puriﬁ er lock-clip.

- Hold the puriﬁ er lock-clip in the appropriate position

(under the sink for example) and ﬁ x it tightly into

place where to screw.

Secure the puriﬁ er in position.

- Fix the puriﬁ er in position, as shown in the ﬁ gure on

the right.

WARRANTY INFORMATION

This water line installation is not covered by the

refrigerator or ice maker manufacturer’s warranty.

Follow these instructions carefully to minimise the risk of

expensive water damage.

Note:

If the coupler does not ﬁ t on the current tap, go

the nearest authorised service dealer and purchase the

right couplers ﬁ ttings.

COUPLER “A”

TAP

COUPLER

SIDE OF

PURIFIER

WATER INLET

SIDE OF PURIFIER

LINE OUTLET

90 degree

PURIFIER WATER

CAUTION

Locking Clip

Insert Locking Clip After

tube seated

WATER SUPPLY

INLET SIDE

PERMEAT

FLOW DIRECTION

Note : You must also ensure

that the cut is square

and not at any sort

of angle as this could

cause a leak

WATER LINE

PURIFIER

WATER

OUTLET SIDE

OF PURIFIER

PURIFIER LOCK-CLIP

WATER TUBE

PURIFIER LOCK-CLIP

PURIFIER

setting up _15

01 SETTING UP

Connect the water line to the

refrigerator.

- Remove the compressor cover of the refrigerator.

- Connect the water line to the valve, as shown in

the ﬁ gure.

- When connected, check if there is any leakage.

If any, repeat the connection.

- Reattach the compressor cover of the refrigerator.

Secure the water line.

- Using clip ”A”, ﬁ x the water

line to the wall (the back of

refrigerator).

- When the water line is

secure, make sure whether

the water line is not

excessively bent, pinched or

squashed.

Removing any residual matter inside

the water supply line after installing

ﬁ lter.

1. Turn ON the main water supply & turn OFF the

valve to the water supply line.

2. Run water through the dispenser until the water

runs clear (approx. 1L). This will clean the water

supply system and remove air from the lines.

3. Additional ﬂ ushing may be required in some

households.

4. Open the refrigerator door and make sure there

are no water leaks coming from the water ﬁ lter.

A newly installed water ﬁ lter cartridge may cause

water to brieﬂ y spurt from the water dispenser.

This is due to air getting into the line. It should

pose no problem to operation.

WATER LINE

INSTRUCTIONS

COMPRESSOR COVER OF

REFRIGERATOR

CONNECTION NUT

CLIP A

WATER LINE

16_ operating

operating the SAMSUNG

side-by-side refrigerator

OPERATING THE REFRIGERATOR

USING THE CONTROL PANEL /

DIGITAL DISPLAY

When not in use the temperature display will turn off,

this is normal.

POWER

FREEZE

BUTTON

Speeds up the time needed

to freeze products in the

freezer. This can be helpful

if you need to quickly freeze

items that spoil easily or if the

temperature in the freezer

has warmed dramatically (For

example, if the door was left

open).

FREEZER

BUTTON

Press the Freezer button to

set the freezer to your desired

temperature, You can set the

temperature between -14°C

(8°F) and -25ºC (-14°F).

ICE TYPE

BUTTON

Use this button to choose

Cubed, Crushed or to turn the

Ice feature off.

FILTER

CHANGE

BUTTON

When you change the ﬁ lter,

press this button for 3

seconds to reset the ﬁ lter

schedule.

VACATION

BUTTON

If you are going on vacation

or business trip or you do not

need to use the refrigerator,

press the Vacation button.

When you select vacation

button for fridge compartment

off, display LED of Vacation will

be on.

It is strongly requested to

remove foods in the fresh-

food compartment and do

not leave the door open

when you select Vacation

function.

CHILD

LOCK

FUNCTION

By pressing the Vacation

button and the Fridge button

simultaneously for 3 seconds,

all buttons will be locked. The

Water dispenser lever and

the Ice lever will not work

either. To cancel this function,

Press these two buttons for 3

seconds again.

FRIDGE

BUTTON

Press the Fridge button to

set the fridge to your desired

temperature.

You can set temperature

between 1°C and 7°C (34°F

and 45°F).

When you use Power Freeze the energy

consumption of the refrigerator will increase.

Remember to turn it off when you don’t

need it and return the freezer to your original

temperature setting.

If you need to freeze large amount of food stuff,

activate Power Freeze function at least 24 hours

before.

5

6

7

1

3

4

2

COOLSELECT MODEL

DISPENSER MODEL

NORMAL MODEL

1

2

3

5

4

6

7

operating _17

02 OPERATING

CONTROLLING THE

TEMPERATURE

CONTROLLING THE FREEZER

TEMPERATURE

The freezer temperature can be set between -14°C

(8°F) and -25ºC (-14°F) to suit your particular needs.

Press the Freezer button repeatedly until the desired

temperature is shown in the temperature display.

Keep in mind that foods like ice cream may melt at

-16ºC (4°F).

The temperature display will move sequentially from

-14°C (8°F) and -25ºC (-14°F). When the display

reaches -14ºC (8°F), it will begin again at -25ºC

(-14°F).

Five seconds after the new temperature is set the

display will again show the actual current freezer

temperature. However, this number will change as

the Freezer adjusts to the new temperature.

The door guards in the freezer of this model are

the two star sections, so the temperature in

two star sections are slightly higher than other

freezer compartment.

CONTROLLING THE FRIDGE

TEMPERATURE

The refrigerator temperature can be set between 7ºC

(46°F) and 1ºC (34°F) to suit your particular needs.

Press the Fridge button repeatedly until the desired

temperature is shown in the temperature display.

The temperature control process for the Fridge works

just like the Freezer process.

Press the Fridge button to set your desired

temperature. After a few seconds, the Fridge will

begin tracking towards the newly set temperature.

This will be reﬂ ected in the digital display.

The temperature of the freezer or the refrigerator

may rise from opening the doors too frequently,

or if a large amount of warm or hot food is

placed in either side.

This may cause the digital display to blink.

Once the freezer and refrigerator return to their

normal set temperatures the blinking will stop.

If the blinking continues, you may need to “reset”

the refrigerator.

Try unplugging the appliance, wait about 10

minutes and then plug back in.

USING THE ICE AND COLD

WATER DISPENSER

Press the Ice Type button to select the type of ice

you want

Ice is made in cubes. When you select

“Crushed”, the icemaker grinds the ice cubes

into crushed ice.

Dispensing ice

Place your glass underneath the ice outlet and push

gently against the ice dispenser lever with your glass.

Make sure the glass is in line with the dispenser to

prevent the ice from bouncing out.

Using the Water Dispenser

Place a glass underneath the water outlet and push

gently against the water dispenser lever with your

glass.

Make sure the glass is in line with the dispenser to

prevent the water from splashing out.

No Ice

Select this if you want to

turn off the icemaker

18_ operating

GUARD FRE-UPP

(Optional)

• Do not put your ﬁ ngers, hands or any

other unsuitable objects in the chute or

ice-maker bucket.

- It may result in personal injury or material

damage.

• Never put ﬁ nger or any other objects in

the dispenser opening.

- It may cause injury.

• Use only the ice maker provided with the

refrigerator.

• The water supply to this refrigerator must

only be installed/connected by a suitably

qualiﬁ ed person and connect to a potable

water supply only.

• In order to operate the ice maker properly,

water pressure of 138 ~ 862 Kpa is

required.

• If you have a long vacation or business

trip and won’t use water or ice

dispensers, close the water valve.

- Otherwise, water leakage may occur.

• Wipe excess moisture from the inside and

leave the doors open.

- Otherwise, odor and mold may develop.

To get more space,you can remove top freezer

drawer since it does not affect thermal and

mechanical characteristics. A declared storage

volume of frozen food storage compartment is

calculated with these drawers removed.

For more space, you can

store food with Guard

FRE-UPP instead of the ice

bucket.

If you remove the ice bucket,

ICE OFF will blink on the

display panel.

USING THE COOLSELECT

ZONE™ DRAWER (OPTIONAL)

Quick Cool

• You can use the Quick Cool feature with the

CoolSelect Zone

TM

.

• “Quick Cool” allows 1~3 canned beverages to cool

within 60 min.

• To cancel this function, press the “Quick Cool”

button again. CoolSelect Zone

TM

returns to the

previous temperature.

• When “Quick Cool” ends, it returns to the “Cool”

temperature setting.

Thaw

• Drips loss and quality deterioration of meats

reduces the freshness of foods.

•

After “Thaw” is selected, warm and cold air is

alternately supplied into the CoolSelect Zone

TM

Drawer.

• Depending on the weight of meat, thawing time

can be selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs

sequentially.

• When “Thaw” ends, CoolSelect Zone

TM

display

returns to “Zero Zone” condition.

• When “Thaw “ ends, there are no juice in the meats

and they are half-freezed condition so it is easy to

cut them for cooking.

• To cancel this option, press any button except

“Thaw”.

• The approximate thawing time of meat and ﬁ sh are

shown below. (Based on 1inch thickness)

THAW TIME WEIGHT

4hours 363g (0.8Ib)

6hours 590g (1.3Ib)

10hours 771g (1.7Ib)

12hours 1000g (2.2Ib)

Depending on the size and thickness of meat

and ﬁ sh, the thawing time may vary.

The above weight represents the total weight of

food in the CoolSelect Zone

TM

Drawer.

Ex) The total thawing time for 400g frozen beef

and 600g frozen chicken will be 10 hours.

With the “Thaw” option, food which is not

needed to thaw in the CoolSelect Zone

TM

Drawer should be removed.

WARNING

CAUTION

WARNING

operating _19

02 OPERATING

Zero Zone (0ºC)

• When “Zero Zone” is chosen, the temperature

of the CoolSelect Zone

TM

Drawer is kept at 0 ºC

regardless of the set refrigerator temperature.

• “Zero Zone” temperature helps keep meat or ﬁ sh

fresh longer.

Cool

• When “Cool” is chosen, the temperature will be the

same as the set temperature of the refrigerator. The

digital panel shows the same temperature as that of

the display panel.

• The CoolSelect Zone

TM

Drawer allows extra

refrigerator space.

Depending on the beverages, the cool-down

time may vary.

For “Quick Cool” option, food stored in

the CoolSelect Zone

TM

Drawer should be

removed.

REMOVING THE FREEZER

ACCESSORIES

Cleaning and rearranging the interior of the freezer is

simple.

1. Remove the Glass shelf by pulling the shelf out as

far as it will go. Then, gently lift it up and remove it.

2. Remove the door bin by holding the door bin with

both hands and then gently lift it up.

3. Remove the Plastic drawer by pulling it out and

slightly lifting it up.

4. ice bucket (freezer)

Remove the Icemaker Bucket by lifting up and

pulling it out slowly.

• Grip the handle as

shown in the ﬁ gure

• Lift the low part slightly

• Take the ice bucket out

slowly.

Do not use excessive force when removing the

cover.

Otherwise, the cover may break and cause

injury.

WARNING

20_ operating

REMOVING THE FRIDGE

ACCESSORIES

1. Remove the spill Proof Glass Shelf by pulling the

shelf out as far as it will go. Then, gently lift it up

and gently remove it.

2. Remove the Vegetable & Fruit Drawer by

pressing on the indentations found on the inside

left and right sides of the Veggie Box/Dry Box

cover and remove by

pulling forward.

Holding the drawer with

one hand, lift it up a

little bit while pulling it

forward and take it out

of the refrigerator.

3. Remove the Gallon Door Bin by holding the bin

with both hands and gently lifting it up.

4. The Z Shelf is attached to the cabinet wall.

Remove the wine shelf by sliding it up and gently

lifting the shelf out of the tabs.

Ensure that the Z Shelf is ﬁ tted as shown in

the diagram and not upside down.

Before removing any

accessories, make sure that

no food is in the way.

When possible, remove the food altogether to

reduce the risk of accidents.

To get the best energy efﬁ ciency of this product,

please leave all selves, drawers and baskets on

their original position like as illustration in page

(18).

CLEANING THE REFRIGERATOR

Do not use Benzene, Thinner or Clorox™

for cleaning.

They may damage the surface of the

appliance and can create a risk of ﬁ re.

Do not spray the refrigerator with water

while it is plugged in, as it may cause an

electric shock.

Do not clean the refrigerator with benzene,

thinner or car detergent for risk of ﬁ re.

REPLACING THE INTERIOR

LIGHT

For LED lamp, please contact service engineer

to replace it.

WARNING

CAUTION

Pagina se încarcă ...

Samsung RSH7UNBP Manual de utilizare

Samsung RSH7UNBP Manual de utilizare

Lucrări conexe

Alte documente