Sames 40C100 WB Manual de utilizare

Marca: Sames

Model: 40C100 WB

Categorie: Pulverizator de vopsea

Tip: Manual de utilizare

DOCUMENTATION

PUMP 40C100 WB

AIRLESS

Manual : 582.030.110-UK - 1902

Date: 08/02/19

Supersede : 27/05/16

Modif.:

TRANSLATION FROM THE ORIGINAL MANUAL

IMPORTANT : Before assembly and start-up, please read and clearly understand all the documents relating to

this equipment (professional use only).

THE PICTURES AND DRAWINGS ARE NON CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT PRIOR NOTICE..

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

578.025.130 1901

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

Pour une utilisation sure, Il est de votre responsabilité

de :

• Lire attentivement tous les documents contenus

dans le CD joint avant la mise en service de

l’équipement,

•

D’installer, d’utiliser, d’entretenir et de réparer

l’équipement conformément aux préconisations de

SAMES KREMLIN ainsi qu’aux réglementations

nationales et/ou locales,

• Vous assurez que les utilisateurs de cet équipement

ont été formés, ont parfaitement compris les règles de

sécurité et qu’ils les appliquent.

To ensure safe use of the machinery, it is your

responsibility to:

•

Carefully read all documents contained on the

enclosed CD before putting the machinery into service,

• Install, use, maintain and repair the machinery in

accordance with SAMES KREMLIN's recommendations

and national and/or local regulations,

• Make sure that the users of the machinery have

received proper training and that they have perfectly

understood the safety rules and apply them.

Eine sichere Nutzung setzt voraus, dass Sie: :

•

alle in der CD enthaltenen Dokumente vor der

Inbetriebnahme der Anlage aufmerksam lesen,

• die Anlage im Einklang mit den Empfehlungen von

SAMES KREMLIN sowie mit den nationalen und/oder

lokalen Bestimmungen installieren, verwenden,

warten und reparieren,

• sich vergewissern, dass die Nutzer dieser Anlage

angemessen geschult wurden, die

Sicherheitsbestimmungen verstanden haben und sie

anwenden.

Para una utilización segura, será de su

responsabilidad:

•

leer atentamente todos los documentos que se

incluyen en el CD adjunto antes de la puesta en servicio

del equipo,

• instalar, utilizar, efectuar el mantenimiento y reparar

el equipo con arreglo a las r

ecomendaciones de

SAMES KREMLIN y a la normativa nacional y/o local,

• cerciorarse de que los usuarios de este equipo han

recibido la formación necesaria, han entendido

perfectamente las normas de seguridad y las aplican.

Per un uso sicuro, vi invitiamo a:

• l

eggere attentamente tutta la documentazione

contenuta nel CD allegato prima della messa in

funzione dell'apparecchio,

•

installare, utilizzare, mantenere e riparare

l'apparecchio rispettando le raccomandazioni di SAMES

KREMLIN, nonché le normative nazionali e/o locali,

•

accertarvi che gli utilizzatori dell'apparecchio

abbiano ricevuto adeguata formazione, abbiano

perfettamente compreso le regole di sicurezza e le

applichino.

Para uma utilização segura, é da sua

responsabilidade:

• Ler atentamente todos os documentos incluídos no

CD em anexo antes de pör o equipamento em

funcionamento,

• Proceder à instalação, utilização, manutenção e

reparação do equipamento de acordo com as

preconizações de SAMES KREMLIN, bem como com

outros regulamentos nacionais e/ou locais aplicáveis,

• Assegurar-se que os utilizadores do equipamento

foram devidamente capacitados, compreenderam

perfeitamente e aplicam as devidas regras de

segurança.

Voor een veilig gebruik dient u:

• alle document op de bijgevoegde cd aandachtig te

lezen alvorens het apparaat in werking te stellen,

• het apparaat te installeren, gebruiken, onderhouden

en repareren volgens de door SAMES KREMLIN

gegeven aanbevelingen en overeenkomstig de

nationale en/of plaatselijke reglementeringen,

• zeker te stellen dat de gebruikers van dit apparaat

zijn opgeleid, de veiligheidsregels perfect hebben

begrepen en dat zij die ook toepassen.

För en säker användning av utrustningen ansvarar ni

för följande:

• Läs noga samtliga dokument som finns på den

medföljande cd-skivan innan utrustningen tas i drift.

•

Installera, använd, underhåll och reparera

utrustningen enligt anvisningarna från SAMES

KREMLIN och enligt nationella och/eller lokala

bestämmelser.

• Försäkra er om att användare av denna utrustning

erhållit utbildning, till fullo förstått säkerhetsföreskrifterna

och tillämpar dem.

Käytön turvallisuuden varmistamiseksi

velvollisuutesi on:

• Lukea huolella kaikki CD:llä olevat asiakirjat ennen

laitteiston käyttöönottoa,

•

Noudattaa laitteiston asennuksessa, käytössä,

kunnossapidossa ja hu

ollossa SAMES KREMLIN in

suosituksia sekä kansallisia ja/tai paikallisia

määräyksiä,

• Varmistaa, että laitteiston käyttäjät ovat koulutettuja

ja ymmärtävät täysin turvallisuusmääräykset ja miten

niitä sovelletaan.

Dla zapewnienia bezpiecznego użytkowania na

użytkowniku spoczywa obowiązek:

• Uważnego zapoznania się ze wszystkimi

dokumentami znajdującymi się na załączonej płycie CD

przed pierwszym uruchomieniem urządzenia,

• Instalowania, użytkowania, konserwacji i naprawy

urządzenia zgodnie z zaleceni

ami firmy SAMES

KREMLIN oraz z przepisami miejscowymi,

• Upewnienia, że wszyscy przeszkoleni użytkownicy

urządzenia zrozumieli zasady bezpieczeństwa i stosują

się do nich.

Pro bezpečné používání jste povinni:

• Před uvedením zařízení do provozu si pozorně

přečíst veškeré dokumenty obsažené na přiloženém

CD,

• Nainstalovat, používat, udržovat a opravovat

zařízení v souladu s pokyny firmy SAMES KREMLIN

a s národními a/nebo místními legislativními předpisy,

• Ujistit se, že uživatelé tohoto zařízení byli vyškoleni,

že dokonale pochopili bezpečnostní pravidla a že je

dodržují.

Za varno uporabo ste dolžni:

• natančno prebrati vse dokumente na CD pred

zagonom stroja,

•

inštalirati, uporabljati, vzdrževati in popravljati

opremo po določilih SAMES KREMLIN in v skladu z

veljavnimi nacionalnimi in/ali lokalnimi predpisi,

•

poskrbeti, da so uporabniki te opreme ustrezno

usposobljeni, poznajo varnostne predpise in da jih

upoštevajo.

V záujme bezpečného je vašou povinnosťou:

• pozorne si prečítať všetky dokumenty obsiahnuté na

priloženom CD predtým, ako zariadenie uvediete do

prevádzky,

• nainštalovať, používať, udržiavať a opravovať

zariadenie v súlade s odporúčaniami spoločnosti

SAMES KREMLIN a národnými a/alebo miestnymi

predpismi,

• uistiť sa, že používatelia tohto zariadenia boli

zaškolení, riadne porozumeli pravidlám bezpečnosti a

používajú ich.

A biztonságos használat érdekében az Ön

felelőssége, hogy:

• a berendezés üzembe helyezése előtt figyelmesen

elolvassa a mellékelt CD által tartalmazott összes

dokumentumot,

• a berendezést a SAMES KREMLIN ajánlasainak

valamint a nemzeti és/vagy helyi szabályozásoknak

megfelelően helyezze üzembe, használja, tartsa karban

és javítsa,

•

megbizonyosodjon róla, hogy a berendezés

felhasználói képzettek, tökéletesen megértették és

alkalmazzák a biztonsági előírásokat.

Pentru o utilizare sigură, este responsabilitatea dvs.

să:

• Citiţi cu atenţie toate documentele de pe CD-ul

anexat, înainte de punerea în funcţiune a

echipamentului,

• Instalaţi, utilizaţi, întreţineţi şi reparaţi echipamentul

conform instrucţiunilor SAMES KREMLIN precum şi

reglementărilor naţionale şi/sau locale,

• Vă asiguraţi că utilizatorii acestui echipament au

fost instruiţi, au înţeles perfect regulile de securitate şi

le aplică integral.

Déclaration(s) de conformité au verso de ce document / Declaration(s) of conformity at the back of this document / Konformitätserklärung(en) auf der Rückseite dieser Unterlage

/ Declaración (es) de conformidad en el reverso de este documento / Dichiarazione/i di conformità sul retro del presente documento

/ Declaração(ções) de conformidade no verso do documento / Conformiteitsverklaring(en) op de keerzijde van dit document / Försäkran om överensstämmelse på omstående sida

av detta dokument / Vaatimustenmukaisuusvakuutukset tämän asiakirjan kääntöpuolella / Deklaracja(e) zgodności na odwrocie dokumentu

/ Prohlášení o shodě se nachází/nacházejí na zadní straně tohoto dokumentu / Deklaracija(e) o skladnosti na hrbtni strani tega dokumenta / Vyhlásenie/-a o zhode sa nachádzajú na

zadnej strane dokumentu / A dokumentum hátlapján szereplő megfelelőségi nyilatkoz(ok) / Declaraţii de conformitate pe versoul acestui document

SAMES KREMLIN N° : 578.025.130-1901

DECLARATION UE DE CONFORMITE

EU DECLARATION OF CONFORMITY

EU- KONFORMITÄTSERKLÄRUNG

DECLARACIÓN UE DE CONFORMIDAD

DICHIARAZIONE DI CONFORMITÀ UE

DECLARAÇÃO UE DE CONFORMIDADE

EU-CONFORMITEITSVERKLARING

EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE

EU- VAATIMUKSENMUKAISUUSVAKUUTUS

DEKLARACJA ZGODNOŚCI UE

EU PROHLÁŠENÍ O SHODĚ

IZJAVA EU O SKLADNOSTI

VYHLÁSENIE O ZHODE

EU-MEGFELELŐSÉGI NYILATKOZAT

DECLARAŢIA DE CONFORMITATE UE

Le fabricant / The manufacturer / Der Hersteller

/ El fabricante / Il produttore / O fabricante

/ De fabrikant / Tillverkare / Valmistaja / Producent / Výrobce

/ Proizvajalec / Výrobca / Gyártó / Fabricantul:

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - FRANCE

Tél. : 33 (0)4 76 41 60 60

Déclare que le matériel désigné ci-après / Herewith declares that the equipment / erklärt hiermit, dass die / Declara que el material designado a

continuación / Dichiara che il materiale sottoindicato / Declara que o material a seguir designado / verklaart dat de hieronder aangeduide apparatuur

/ Kungör att den utrustning som anges här nedan / ilmoittaa, että alla mainitut laitteistot / Oświadcza, że wymienione poniżej urządzenia / Prohlašuje,

že níže uvedené vybavení / Izjavlja, da je opisana oprema spodaj / Vyhlasuje, že zariadenie uvedené nižšie / Kijelenti, hogy a megjelölt anyag a

továbbiakban / Declară că echipamentul precizat mai jos:

POMPES AIRLESS® / AIRLESS PUMPS / AIRLESS PUMPE / BOMBAS AIRLESS

40C100 40C100 WB

Est conforme à la législation d’harmonisation de l’Union applicable suivante / Is in conformity with the relevant Union harmonisation legislation / Erfüllt

die einschlägigen Harmonisierungsrechtsvorschriften der Union / es conforme con la legislación de armonización pertinente de la Unión / è conforme

alla pertinente normativa di armonizzazione dell’Unione / in overeenstemming met de desbetteffende harmonisatiewetgeving van de Unie / med den

relevanta harmoniserade unionslagstiftningen / on asiaa koskevan unionin yhdenmukaistamislainsäädännön vaatimusten mukainen / jest zgodny z

odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego / Shoduje se s následující příslušnou evropskou harmonizační legislativou

/ V skladu s harmonizirano zakonodajo Unije / Je v súlade s uplatniteľnými harmonizačnými právnymi predpismi EÚ / Megfelel a következő

alkalmazandó uniós harmonizációs szabályozásnak / Este conform cu legislaţia aplicabilă de armonizare de mai jos

Directive ATEX / ATEX Directive /

ATEX Richtlinie / Directiva ATEX / Direttiva ATEX / Diretiva ATEX

/ ATEX-Richtijn / ATEX-direktivet / ATEX-direktivi / Dyrektywa ATEX / Směrnice ATEX / Direktiva ATEX / Smernica ATEX

/ ATEX-irányelv 2014/34/UE

II 2G T1

40C50 40C50 WB

Est conforme à la législation d’harmonisation de l’Union applicable suivante / Is in conformity with the relevant Union harmonisation legislation / Erfüllt

die einschlägigen Harmonisierungsrechtsvorschriften der Union / es conforme con la legislación de armonización pertinente de la Unión / è conforme

alla pertinente normativa di armonizzazione dell’Unione / in overeenstemming met de desbetteffende harmonisatiewetgeving van de Unie / med den

relevanta harmoniserade unionslagstiftningen / on asiaa koskevan unionin yhdenmukaistamislainsäädännön vaatimusten mukainen / jest zgodny z

odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego / Shoduje se s následující příslušnou evropskou harmonizační legislativou

/ V skladu s harmonizirano zakonodajo Unije / Je v súlade s uplatniteľnými harmonizačnými právnymi predpismi EÚ / Megfelel a következő

alkalmazandó uniós harmonizációs szabályozásnak / Este conform cu legislaţia aplicabilă de armonizare de mai jos

Directive ATEX / ATEX Directive /

ATEX Richtlinie / Directiva ATEX / Direttiva ATEX / Diretiva ATEX

/ ATEX-Richtijn / ATEX-direktivet / ATEX-direktivi / Dyrektywa ATEX / Směrnice ATEX / Direktiva ATEX / Smernica ATEX

/ ATEX-irányelv 2014/34/UE

II 2G T2

SAMES KREMLIN - 2 - N° : 578.025.130-1901

40C260 40C260_2

65C260 65C260_2

Est conforme à la législation d’harmonisation de l’Union applicable suivante / Is in conformity with the relevant Union harmonisation legislation / Erfüllt

die einschlägigen Harmonisierungsrechtsvorschriften der Union / es conforme con la legislación de armonización pertinente de la Unión / è conforme

alla pertinente normativa di armonizzazione dell’Unione / in overeenstemming met de desbetteffende harmonisatiewetgeving van de Unie / med den

relevanta harmoniserade unionslagstiftningen / on asiaa koskevan unionin yhdenmukaistamislainsäädännön vaatimusten mukainen / jest zgodny z

odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego / Shoduje se s následující příslušnou evropskou harmonizační legislativou

/ V skladu s harmonizirano zakonodajo Unije / Je v súlade s uplatniteľnými harmonizačnými právnymi predpismi EÚ / Megfelel a következő

alkalmazandó uniós harmonizációs szabályozásnak / Este conform cu legislaţia aplicabilă de armonizare de mai jos

Directive ATEX / ATEX Directive /

ATEX Richtlinie / Directiva ATEX / Direttiva ATEX / Diretiva ATEX

/ ATEX-Richtijn / ATEX-direktivet / ATEX-direktivi / Dyrektywa ATEX / Směrnice ATEX / Direktiva ATEX / Smernica ATEX

/ ATEX-irányelv 2014/34/UE

II 2G T3

La présente déclaration de conformité est établie sous la seule responsabilité du fabricant / This declaration of conformity is issued under the sole

responsibility of the manufacturer / Die alleinige Verantwortung für die Ausstellung dieser Konformitätserklärung trägt der Hersteller / La presente

declaración de conformidad se expide bajo la exclusiva responsabilidad del fabricante / La presente dichiarazione di conformità è rilasciata sotto la

responsabilità esclusiva del fabbricante / A presente declaração de conformidade é emitida sob a exclusiva responsabilidade do fabricante / Deze

conformiteitsverklaring wordt verstrekt onder volledige verantwoordelijkheid van de fabrikant / Denna försäkran om överensstämmelse utfärdas på

tillverkarens eget ansvar / Tämä vaatimustenmukaisuusvakuutus on annettu valmistajan yksinomaisella vastuulla / Niniejsza deklaracja zgodności

wydana zostaje na wyłączną odpowiedzianość producenta / Toto prohláŝení o skodě se vydává na výhradní odpovědnost výrobce / Za izdajo te izjave

o skladnosti je odgovoren izključno proizvajalec / Toto vyhlásenie o zhode sa vydáva / na vlastnú zodpovednosť výrobcu / Ezt a megfelelőségi

nylatkozatot a gyártó kizárólagos felelőssége mellett adják ti / Prezenta declaraţie de conformitate este emisă pe răspunderea exclusivă a

producătorului.

Hervé WALTER

Directeur Innovation & Développement / Innovation & Development

Director / Direktor für Innovation & Entwicklung / Director de

Inovación y Desarrollo / Direttore Innovazione e sviluppo

/ Diretor de Inovação / Manager Innovatie en Ontwikkeling / Direktör

för Forskning och Utveckling / Innovaatio- ja kehitysjohtaja

/ Dyrektor ds. Innowacji I Rozwoju / Ředitel pro inovace a vývoj

/ Direktor za inovacije in razvoj / Riaditeľ pre inováciu a rozvoj

/ Innovációs és fejlesztési igazgató / Director Inovaţie şi Dezvoltare

Fait à Meylan, le / Established in Meylan, on / Geschehen zu Meylan, am / En Meylan, a / Redatto a Meylan, / Vastgesteld te Meylan, / Utformat i

Meylan, den / Meylan, Ranska, / Sporządzono w Meylan, dnia / Meylan, dnia / V Meylanu, / V Meylan dňa / Kelt Meylanban, / Întocmită la Meylan,

pe data de 31/01/2019 - 01/31/2019

SAMES KREMLIN - 3 - N° : 578.025.130-1901

SAMES KREMLIN N° : 578.001.130-UK-1804

INSTALLATION AND SAFETY

INSTRUCTIONS

TRANSLATION FROM THE ORIGINAL MANUAL

IMPORTANT :Before assembly and start-up, please read and clearly understand all the

documents relating to this equipment (professional use only).

THE PICTURES AND DRAWINGS ARE NON CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT

PRIOR NOTICE.

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

SAMES KREMLIN - 1 - N° : 578.001.130-UK-1804

1. SAFETY INSTRUCTIONS

GENERAL SAFETY INSTRUCTIONS

CAUTION : The equipment can be dangerous if you do not follow our

instructions concerning installation and servicing described in this manual

and in accordance with applicable European standards and local national safety

regulations.

Please carefully read all the instruction literature before operating your

equipment.

Only trained operators can use the equipment.

The foreman must ensure that the operator has understood the safety instructions for this equipment as

well as the instructions in the manuals for the different parts and accessories.

Read carefully all instruction manuals, label markings before operating the equipment.

Incorrect use may result in injury. This equipment is for professional use only. It must be used only for

what it has been designed for. Never modify the equipment. The parts and accessories supplied must be

regularly inspected. Defective or worn parts must be replaced.

Guards (motor cover, coupling shields, connectors,…) have been designed for a

safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure and / or

property damage due to destruction, the overshadowing or the partial or total

removal of the guards.

Never exceed the equipment components' maximum working pressure.

Comply with regulations concerning safety, fire risks, electrical regulations in force in the country of final

destination of the material. Use only products or solvent compatible with the parts in contact with the

material (refer to data sheet of the material manufacturer).

PICTOGRAMS

ADFECG

NIP HAZARD WARNING

MOVING

ELEVATOR

WARNING

MOVING PARTS WARNING

MOVING SHOVEL DO NOT

EXCEED THIS

PRESSURE

HIGH

PRESSURE

HAZARD

HJLKMQ

RELIEF OR

DRAIN VALVE WARNING

HOSE UNDER

PRESSURE

WEAR GLASSES

OBLIGATORY WEAR OF

GLOVES IS

OBLIGATORY

PRODUCT

VAPOR

HAZARDS

WARNING

HOT PARTS OR

AREAS

NPR

ELECTRICAL

HAZARD WARNING

FIRE HAZARDS EXPLOSION

HAZARDS GROUNDING WARNING

(USER) WARNING

SERIOUS

INJURIES

SAMES KREMLIN - 2 - N° : 578.001.130-UK-1804

PRESSURE HAZARDS

Current legislation requires that an air relief valve be fitted in the air supply circuit to the air

motor to prevent over pressurisation. This safety feature,ensures that it is not possible to supply

the air motor with excessive air pressure that may cause injury.

Please ensure that a material drain valve is fitted in the fluid circuit to drain and depressurise the

circuit. Once depressurised and drained, work /servicing may then commence on the equipment

Please remember to close these valves when restarting the system.

HIGH PRESSURE INJECTION HAZARDS

When working with high pressure equipment, special care is required. Fluid leaks can occur.

There is a risk of material being injected to any exposed parts of body, this could cause severe

injury :

medical care must be sought immediately if paint is injected under the skin or in other

parts of the body (eyes, fingers).

never point the spray gun at any one. Never try to stop the spray with your hands or fingers

nor with rags or similars.

follow the shut down procedure and always depressurize air and fluid circuits before

carrying out any servicing on the gun (cleaning, checking, maintenance of the material or

cleaning of the gun nozzles).

for the guns equipped with a safety device, always lock the trigger when not in use.

FIRE - EXPLOSION - SPARKS - STATIC ELECTRICITY HAZARDS

A poor earth connection, inadequate ventilation, sparks or static electricity can cause an

explosion or fire. to avoid these risks when using or servicing SAMES KREMLIN equipment, the

following safety procedures must be followed :

ensure a good earth connection and ground the parts to be handled i.e. solvents, materials,

components and equipment,

ensure adequate ventilation,

keep working area clean and free from waste solvents, chemicals, or solid waste i.e. rags,

paper and empty chemicals drums,

never use electrical switches / power if in an atmosphere of volatile solvent vapour,

stop working immediately in case of electrical arcs,

never store chemicals and solvents in the working area.

use paint whose flash point is the highest possible to prevent from any formation of gas

and inflammable vapours (refer to materials' safety instructions),

install a cover on the drums to reduce the diffusion of gas and vapours in the spraybooth.

TOXIC PRODUCT HAZARDS

Toxic products or vapours can cause severe injury not only though contact with the body, but also

if the products are ingested or inhaled. It is imperative :

to know the material products and their risks,

notified or hazardous materials must be stored in accordance with the regulations,

the material must be stored in an appropriate container, never place materials in a

container where there is a risk of spillage or leakage,

a procedure must be applied for the safe disposal of waste material. It must comply with all

prevailing regulations and legislations of the country where the equipment is to be used,

protective clothing should always be worn in compliance with the material manufacturers'

recommendations,

depending on the application and chemical safety instructions, safety glasses, hearing

protective earplug, gloves, foot wear, protective masks and possible breathing equipment

should be worn to comply with the regulations (Refer to chapter "Safety equipment of

SAMES KREMLIN selection guide).

SAMES KREMLIN - 3 - N° : 578.001.130-UK-1804

CAUTION!

It is forbidden to use material containing high concentrations of halogenated hydrocarbon

solvents with aluminium or zinc fillers .Non-compliance with the instructions may cause

explosion risk causing serious or fatal injury.

EQUIPMENT REQUIREMENTS

Guards (motor cover, coupling shields, connectors,…) have been designed for

a safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure

and / or property damage due to destruction, the overshadowing or the

partial or total removal of the guards.

PUMP

Before carrying out any work, it is imperative to read and clearly understand the disassembly and

reassembly instructions before servicing. The operator must understand the equipment and the

safety instructions. These instructions are available in the equipment manuals.

The air motor is designed to be mounted with a pump. Never modify any components or

couplings. When operating, please keep hands away from moving parts. Before starting up the

equipment, please read the PRESSURE RELIEF instructions. Please ensure that any relief or

drain valves fitted are in good working order.

HOSES

Keep hoses out of circulation areas, moving parts or hot surfaces,

Never expose product hoses to temperature higher than + 60°C / 140° F or lower than 0°C

/ 32° F,

Never pull or use the hoses to move the equipment,

Tighten all fittings as well as the hoses before operating the equipment,

Check the hoses regularly; change them if they are damaged,

Never exceed the maximum working pressure (MWP) indicated on the hose.

USED PRODUCTS

Considering the wide variety of products that are available and can be used in our equipment it is

impossible to check and make recommendations for all chemical data,regarding the risks of

possible chemical attack and their long term chemical reaction

SAMES KREMLIN can not be held liable for :

compatibility of wetted parts,

risks to staff and the surroundings,

for worn or defective parts, for faulty equipment or units, or the qualitiy of final product.

It is the responsibility of the user to know and prevent any possible risks such as toxic vapours,

fires or explosions. He shall determine the risks of immediate reactions or pursuant to repeated

exposures of the staff,

SAMES KREMLIN shall not be liable for physical injuries, direct or indirect material damages

caused by the use of chemicals.

SAMES KREMLIN - 4 - N° : 578.001.130-UK-1804

2. HANDLING

Check the weight and the dimensions of the equipment

(



refer to 'Technical features' section of the instruction manual

If weight and dimensions are too important, the unloading must be carried out by means of a forklift or

any other appropriate means with a qualified personnal and in a clear horizontal area to prevent from

risks of damage injury or an accident.

The centre of gravity is not in the centre of the machine : carry out by hand a stability-test after having

lifted the whole at 10 cm / 3.937" maximum.

After the unloading, the handling of the whole (eg: elevator pump) is carried out by means of a pallet

truck taking the bottom part of the frame.

Remark : Each pump motor is fitted with a ring. The ring is designed for the hoisting of one

pump and can not be used for the handling of the complete assembly.

3. STORING

Storing before installation :

- Storing ambient temperature : 0 / +50 °C / 0 / +122°F

- Protect the whole against dust, water trickling, dampness and shocks.

Storing after installation :

- Operating temperature : +15 / +35 °C / +59 / +138.2° F

- Protect the whole against dust, water tricling, dampness and shocks.

4. INSTALLATION OF THE EQUIPMENT

The machine is installed on a stable horizontal floor (for eg a concrete flag).

The machine shall be made stable by the use of holding down bolts or by the use of other anchoring

methods, strong enough to prevent unintended bodily movement of the equipment.

To avoid risks caused by static electricity, the equipment as well as its components must

be grounded.

For the pumping equipments (pumps, pneumatic rams, frame…), a section wire of 2.5

mm² is fixed on the material. Use this wire to connect the material to “the general ground”.

In case of severe environments (mechanical protection of the wire of earthing insufficient,

vibrations, mobile material…) where function damages at the ground are probable, the user

have to replace the provided wire of 2.5 mm² by a device more adapted to its environment

(wire with a more important section, bonding strip, fixing by thimble with eyelet…).

The continuity of the ground must be controlled by a qualified electrician. If the continuity of

the ground is not ensured, check the terminal, the wire and the earthing point. Never use the

material without have solved this problem.

In the severe cases of environments (mechanical protection of the wire of earthing

insufficient, vibrations, mobile material…) where damages of the function put at the ground

are probable, the user will have to replace the wire of 2.5 mm² provided, by a device more

adapted to its environment (wire of more important section, bonding strip, fixing by thimble

with eyelet…),

The gun must be 'grounded' via a material hose or an air hose. In case of spraying by

means of a gun with cup, the air hose must be conductive,

The materials to be painted must also be grounded.

All the materials situated in the working area shall be grounded.

SAMES KREMLIN - 5 - N° : 578.001.130-UK-1804

Never store more than necessary inflammable materials inside the working area,

The materials must be stored into approved drums and grounded,

Use only grounded metals containers for the use of cleaning solvents,

Cardboard and paper are prohibited.

5. MARKING OF THE EQUIPMENT

Each equipment has a label plate with the name of the manufacturer, the equipment part number,

the interesting informations to use correctly the equipment (pressure, voltage,…) and sometimes

the above pictogram.

The equipment is designed with and consists of high quality materials and components which can

be re-used.

The 2012/19/UE European Directive covers all equipments with a crossed-out bin pictogram.

Please inform yourself about the collection systems for electric and electronic equipments.

Please act in accordance with local rules and do not dispose of old equipment with household

wastes. A correct disposal of old equipment will help prevent negative consequences for the

environment and health.

SAMES KREMLIN N° : 578.160.110-UK-1812

STAINLESS STEEL

AIRLESS PUMP

40C100 WB

Disassembly / Reassembly

TRANSLATION FROM THE ORIGINAL MANUAL

IMPORTANT : Before assembly and start-up, please read and clearly understand all the

documents relating to the equipment (professional use only).

THE PICTURES AND DRAWINGS ARE NOT CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT PRIOR

NOTICE.

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

SAMES KREMLIN - 1 - N° : 578.160.110-UK-1812

CAUTION :

Before any action on the pump, shut off the compressed air supply and

depressurize the system.

The pump is manufactured under the ATEX agreement and can not be modified.

SAMES KREMLIN will not be held responsible for any failure to comply with that instruction.

Guards (air motor cover, coupling shields, housings …) have been designed for

safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure and / or

damage to property due to removal or partial removal of the guards

 SUCTION VALVE (DOC. 573.397.050)

Unscrew the suction valve (5) by holding the fitting (27).

The ball (10) is secured on the valve (26) by means of a circlips (9).

Clean the parts.

Change the seal (25).

Reinstall the suction valve (5). Replace the parts if necessary.

 EXHAUST VALVE AND MOBILE PACKING

Unscrew the cylinder (2) and pull it downwards.

Unscrew the exhaust valve (6) by holding the piston (3).

Remove the ball (17), the GT washer (12) and the seal (13a / 13c).

Clean the parts.

Remount the parts in the reverse order of the disassembly sequence.

For that :

 Install the seal (13a / 13c), the washer (12) and the ball (17) onto the exhaust valve (6).

 Screw the exhaust valve (6) into the piston. The seal must be blocked by screwing the exhaust

valve (6) strongly.

If necessary replace seal (8) when reinstalling cylinder (2).

SAMES KREMLIN - 2 - N° : 578.160.110-UK-1812

 UPPER PACKING

Separate the piston rod from the motor and

the piston (3) from the fluid section.

Unscrew the wetting-cup (4) by means of the

wrench supplied with the pump.

Pull the piston (3) upwards to remove the

seals (21 and 22) or the upper packing (18a /

18c).

Reinstall parts in reverse order. Be certain

seals (21 and 22) or upper packing (18a / 18c)

are installed properly (direction, order and

assembly dimension).

Tighten wetting-cup (4).

After reassembly, fill up the pump with

solvent and increase pressure to maximum

in the fluid section. Then stop the pump

and open exhaust valve to depressurize.

Retighten the wetting-cup (4) by means of

the wrench in order to be in accordance

with the opposite drawing.

 REVERSING BLOCK (MOTOR) (DOC. 573.087.040)

Guards (air motor cover, coupling shields, housings …) have been designed for

safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure and / or

damage to property due to removal or partial removal of the guards

Disassemble cover (32) by removing the 3 CHc screws (33).

Dissociate female yoke (12) from reversing block lever (9).

Dismount reversing block by removing screws (10 and 8).

Reinstall the new reversing block in the reverse order of the disassembly sequence.

31.85 mm ±0.5

 CAUTION : The number of spirals must equally be distributed on each fastening

parts in order to get the above dimension.

Before reassembling the different components :

- Clean the parts with the appropriate cleaning solvent,

- Install new seals if it is necessary, after having lubricated them with PTFE grease,

- Lubricate the piston and the inside of the cylinder to prevent from damaging the seals,

- Install new parts if it is necessary.

SAMES KREMLIN - 3 - N° : 578.160.110-UK-1812

 ASSEMBLY INSTRUCTIONS

Index Instruction Description Part number

A 1 PTFE grease 'TECHNILUB' grease

(10 ml / 0.0026 US gal) 560.440.101

A 2 Anti-seize grease Grease box (450 g / 0.99 lb) 560.420.005

C 1 Medium strength

Aneorobic Pipe sealant Loctite 577 (250 ml / 0.066 US gal) 554.180.015

A 1

A 2

C 1

Doc. 573.394.050

Date/Datum/Fecha : 23/10/18

Annule/Cancels/

Ersetzt/Anula : 07/03/12

Modif. / Änderung : Mise à jour

/ Update / Aktualisierung

/ Actualización

KREMLIN REXSON  SAMES

KREMLIN ; 40-50 WB  40C100 WB

Pièces de rechange

Spare parts list

Ersatzteilliste

Piezas de repuesto

POMPE AIRLESS, modèle 40C100 WB

(Clapet aspiration : 1") AIRLESS PUMP, model 40C100 WB

(Suction valve : 1")

AIRLESS PUMPE, model 40C100 WB

(Ansaugventil: 1") BOMBA AIRLESS, tipo 40C100 WB

(Válvula aspiración : 1")

SAMES KREMLIN 2 Doc. / Dok : 573.394.050

POMPE MURALE,

modèle 40C100 WB

sans filtre, sans canne d’aspiration

WALL MOUNTED PUMP,

model 40C100 WB

without filter, without suction rod

WANDANLAGE,

Modell 40C100 WB

ohne Filter, ohne Saugschlauch

BOMBA MURAL,

tipo 40C100 WB

sin filtro, sin caña de aspiración

151.785.510

Ind # Désignation Description Bezeichnung Denominación Qté

- NC / NS Pompe 40C100 WB nue Bare pump,

model 40C100 WB Pumpe 40C100 WB,

nackt Bomba sola,

tipo 40C100 WB 1

*1 146 270 000  Moteur 2000-4

(voir Doc. 573.046.050)  Air motor,

model 2000-4 (refer to

Doc. 573.046.050)

 Luftmotor 2000-4

(siehe Dok. 573.046.050)  Motor, tipo 2000-4

(consultar Doc.

573.046.050)

*2 144 960 800  Hydraulique C100 WB

(voir Doc. 573.397.050)  Fluid section,

model C100 WB (refer to

Doc.397.050)

 Hydraulikteil C100 WB

(siehe Dok.

573.397.050)

 Hidráulica, tipo C100

WB (consultar Doc.

573.397.050)

3 051 770 001  Tirant  Tie-rod, connecting  Stehbolzen  Tirante 4

4 953 010 021  Ecrou HM 10  Nut, model HM 10  Mutter HM 10  Tuerca, tipo HM 10 4

5 963 040 021  Rondelle MN 10  Washer, model MN 10  Scheibe MN 10  Arandela, tipo MN 10 4

- 050 311 902  Ressort de protection  Protective spring  Feder  Muelle de protección 1

*- 151 775 010 Ensemble fixation Mounting assembly Montageplatte kpl. Conjunto de fijación 1

6 051 770 101  Plaque d’interface  Plate  Befestigunsplatte  Placa 1

7 933 011 279  Vis H 8 x 20  Screw, model H 8 x 20  Schraube H 8 x 20  Tornillo, tipo H 8 x 20 1

8 933 151 147  Vis CHc M 8 x 10  Screw,

model CHc M 8 x 10  Schraube

CHc M 8 x 10  Tornillo,

tipo CHc M 8 x 10 1

9 NC / NS  Vis HM 8 x 25  Screw,

model HM 8 x 25  Schraube HM 8 x 25  Tornillo,

tipo HM 8 x 25 2

14 88 664  Rondelle W8  Washer, model W8  Scheibe W8  Arandela, tipo W8 2

15 963 040 019  Rondelle MN 8  Washer, model MN 8  Scheibe MN 8  Arandela, tipo MN 8 2

16 953 010 019  Ecrou HM 8  Nut, model HM 8  Mutter HM 8  Tuerca, tipo HM 8 2

*10 151 790 160 Equipement d'air 1/2"

(voir Doc. 573.403.050) Air supply, model 1/2"

(refer to Doc.

573.403.050)

Luftausrüstung 1/2"

(siehe Dok. 573.403.050) Equipo de aire 1/2"

(consultar Doc.

573.403.050)

11 904 523 006 Raccord,

M 3/8 BSP - M 1/2 BSP Fitting, double male,

3/8 BSP - 1/2 BSP Doppelnippel

AG 3/8 BSP - 1/2 BSP Racor,

M 3/8 BSP - M 1/2 BSP 1

12 904 123 004 Coude FF 1/2 Elbow, FF 1/2 Winkelnippel IG 1/2 Codo, HH 1/2 1

13 050 102 401 Raccord,

M 3/4 NPS - M 1/2 G Fitting, double male,

3/4 NPS - 1/2 G Doppelnippel

AG 3/4 NPS - 1/2 G Racor,

M 3/4 NPS - M 1/2 G 1

19 050 102 457 Raccord inox MM 1"G Fitting, model double

male, 1"G stainless steel Nippel, Edelstahl, AG 1"G Racor de inox,

tipo MM 1"G 1

24 905 210 404 Coude MF 1" inox Elbow, model MF 1"

stainless steel Winkelnippel, Edelstahl,

AG 1" - IG 1" Codo, tipo MH 1" de inox 1

SAMES KREMLIN 3 Doc. / Dok : 573.394.050

POMPE MURALE,

modèle 40C100 WB

avec filtre, sans canne d’aspiration

WALL MOUNTED PUMP,

model 40C100 WB

with filter, without suction rod

WANDANLAGE,

Modell 40C100 WB

mit Filter, ohne Saugschlauch

BOMBA MURAL,

tipo 40C100 WB

con filtro, sin caña de aspiración

151.785.520

Ind. 21

21a

21d

21c

21b

Ind # Désignation Description Bezeichnung Denominación Qté

- 151 785 510 Pompe murale sans filtre,

sans canne d’aspiration Wall mounted pump

without Filter, without

suction rod

Wandpumpe ohne Filter,

ohne Saugschlauch Bomba mural sin filtro, sin

caña de aspiración 1

20 155 581 450 Filtre AIRLESS® inox 3/4

(voir Doc. 573.327.050) AIRLESS filter,

model 3/4, st steel

(siehe Doc. 573.327.050)

AIRLESS Filter 3/4,

Edelstahl (refer to Doc.

573.327.050)

Filtro AIRLESS de inox,

tipo 3/4 (consultar Doc.

573.327.050)

- 000 161 112 Tamis n° 12 (280 µ) Screen n° 12

(280 µ - 55 Mesh) Filterelement Sieb Nr. 12

(280 µ) Tamiz n° 12 (280 µ) 1

- 903 090 220 Vanne HP FF 3/8 BSP HP valve,

model FF 3/8 BSP Kugelhahn, IG 3/8 BSP Válvula AP,

tipo HH 3/8 BSP 1

21 055 490 020 Clapet anti-retour MF 3/4" Non-return valve, model

MF 3/4" Rückschlagventil,

AG/IG 3/4" Válvula anti retorno, tipo

MH 3/4" 1

21a NC / NS  Support siège  Seat support  Sitzhalterung  Soporte asiento 1

21b NC / NS  Clapet  Valve  Ventil  Válvula 1

21c 109 420 289  Joint (les 10)  Seal (pack of 10)  Dichtung (Satz á10 st.)  Junta (bolsa de 10) 1

21d 907 414 242  Bille  16 (inox 440C)  Ball, model  16

(stainless steel 440C)  Kugel  16

(aus Edelstahl 440C)  Bola, tipo  16

(de inox 440C) 1

22 905 210 206 Raccord inox

M 3/4 NPT - M 3/8 NPT Fitting, model double

male 3/4 NPT - 3/8 NPT,

stainless steel

Langnippel, Edelstahl

AG 3/4 NPT - AG3/8 NPT Racor de inox, tipo

M 3/4 NPT - M 3/8 NPT 1

23 049 596 000 Canne de purge inox

Ø 16 Drain rod, stainless steel,

Ø 16 Entleerungsrohr,

Edelstahl Ø 16 Caña de purga inox Ø 16 1

SAMES KREMLIN 4 Doc. / Dok : 573.394.050

Ind # Désignation Description Bezeichnung Denominación Qté

- 905 210 515 Raccord inox

M 3/4 NPT - M 3/4 JIC Fitting, model double

male, 3/4 NPT - 3/4 JIC

stainless steel

Anschluss aus Edelstahl

AG 3/4 NPT - AG 3/4 JIC Racor de inox,

tipo M 3/4 NPT

- M 3/4 JIC

- 905 240 002 Raccord inox

MM 3/8 NPT Fitting, double male,

3/8 NPT Doppelnippel

AG 3/8 NPT Racor inox,

MM 3/8 NPT 1

- 050 102 436 Raccord inox

M 18 x 125 - M 3/8 BSP Adaptor, stainless steel,

double male

18x125 - 3/8BSP

Doppelnippel - Edelstahl

AG 3/8 BSP - M 18x1,25 Racor inox,

M 18 x 125 - M 3/8 BSP 1

POMPE MURALE

avec filtre et canne d’aspiration WALL MOUNTED PUMP

with filter and suction rod #

WANDANLAGE

mit Filter und Saugschlauch BOMBA MURAL

con filtro y caña de aspiración 151.785.550

Ind # Désignation Description Bezeichnung Denominación Qté

- 151 785 520 Pompe murale avec filtre,

sans canne d’aspiration Wall mounted pump with

filter, without suction rod Wandpumpe mit Filter,

ohne Saugschlauch Bomba mural con filtro,

sin caña de aspiración 1

17 921 270 101 Canne d'aspiration 1" Suction rod, model 1" Saugschlauch 1" Caña de aspiración,

tipo 1" 1

POMPE 40C100 WB SUR CHARIOT CART MOUNTED PUMP, model 40C100 WB #

PUMPE 40C100 WB FAHRBAR BOMBA 40C100 WB SOBRE CARRETILLA 151.785.500

Ind # Désignation Description Bezeichnung Denominación Qté

- 151 785 550 Pompe murale avec filtre

et canne d’aspiration Wall mounted pump with

filter and suction rod Wandpumpe mit Filter

und Saugschlauch Bomba mural con filtro y

caña de aspiración 1

- 051 221 000 Chariot (2 bras) Cart (2 arms) Fahrgestell (2 Arme) Carretilla (2 brazos) 1

- 056 100 199 Panneau de fixation Fixing plate Befestigungsplatte Panel de fijación 1

SAMES KREMLIN 5 Doc. / Dok : 573.394.050

POMPE MURALE,

modèle 40C100 WB avec filtre , chariot

pistolet Airless® Sflow - 275 bar

avec raccord tournant

WALL MOUNTED PUMP,

model 40C100 WB with filter, cart

Airless Sflow gun - 275 bar / 3989 psi

with swivel fitting

WANDANLAGE , Modell 40C100 WB

mit Filter, Fahrgestell

Pistole Airless Sflow - 275 bar

mit Drehgelenk

BOMBA MURAL, tipo 40C100 WB

con filtro, carretilla

pistola Airless Sflow - 275 bar

con racor giratorio

151.265.305

Ind # Désignation Description Bezeichnung Denominación Qté

- 151 785 550 Pompe murale avec filtre Wall mounted pump with

filter Wandpumpe mit Filter Bomba mural con filtro 1

- 051 221 000 Chariot (2 bras) Cart (2 arms) Fahrgestell (2 Arme) Carretilla (2 brazos) 1

- 135 740 427 Pistolet Sflow 275 bar

avec raccord tournant

(voir Doc. 573.459.050)

Sflow gun, model 275 bar

/ 3989 psi with swivel

fitting (refer to Doc.

573.459.050)

Pistole Sflow, 275 bar

mit Drehgelenk

(Siehe Dok. 573.459.050)

Pistola Sflow 275 bar

con racor giratorio

(consultar Doc.

573.459.050)

- 905 160 201 Raccord acier,

M 1/2 JIC - M 3/4 JIC Fitting, steel,

double male,

1/2 JIC - 3/4 JIC

Doppelnippel, Stahl

AG 1/2 JIC - 3/4 JIC Racor acero,

M 1/2 JIC - M 3/4 JIC 1

- 76 085 Tuyau

( 9,5 mm - 3/4 JIC

- Lg. 10 m - 425 bar)

Hose

( 9.5 mm / 3/16"

- 3/4 JIC - 10 m / 33 ft

length

- 425 bar / 6163.7 psi)

Schlauch

( 9,5 mm - 3/4 JIC

- Länge 10 m - 425 bar)

Tubería

( 9,5 mm - 3/4 JIC

-Longitud 10 m

- 425 bar)

- 050 450 155 Tuyau

( 6,3 mm - 1/2 JIC

- Lg. 1,6 m - 240 bar)

Hose

( 6,3 mm / 1/4"

- 1/2 JIC - 1.6 m / 5.25 ft

length

- 240 bar / 3480 psi)

Schlauch

( 6,3 mm - 1/2 JIC

- Länge 1,6 m - 240 bar)

Tubería

( 6,3 mm - 1/2 JIC

-Longitud 1,6 m

- 240 bar)

- 056 100 199 Panneau de fixation Fixing plate Befestigungsplatte Panel de fijación 1

SAMES KREMLIN 6 Doc. / Dok : 573.394.050

OPTIONS - ON REQUEST - OPTIONEN - OPCIONES

Ind # Désignation Description Bezeichnung Denominación Qté

- 151 740 200 Régulateur de

pulvérisation (voir Doc.

573.035.050)

Atomizing air regulator

(refer to

Doc.573.035.050)

Zerstäuberluft

Reglereinheit (siehe Dok.

573.035.050)

Manorreductor de

pulverización (consultar

Doc. 573.035.050)

ACCESSOIRES - ACCESSORIES - ZUBEHÖR - ACCESORIOS

Ind. 31

Ind # Désignation Description Bezeichnung Denominación Qté

- 149 990 020 Flacon de lubrifiant T

(125 ml) T lubricant

(125 ml / 4.4 oz) Spülmittel T (125 ml) Botella de lubricante T

(125 ml) 1

31 044 950 008 Clé (pour cuve presse-

garniture) Wrench (for wetting cup) Schlüssel für

Spülmitteltasse Llave (para

prensaestopa) 1

* Pièces de maintenance préconisées.

* Preceding the index number denotes a suggested spare part.

* Bezeichnete Teile sind empfohlene Ersatzteile.

* Piezas de mantenimiento preventivas.

N C : Non commercialisé.

N S : Denotes parts are not serviceable.

N S : Bezeichnete Teile gibt es nicht einzeln.

N S : no suministrado.

Pagina se încarcă ...

Sames 40C100 WB Manual de utilizare

Marca: Sames

Model: 40C100 WB

Categorie: Pulverizator de vopsea

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

English: Sames 40C100 WB User manual
italiano: Sames 40C100 WB Manuale utente

Sames 40C100 WB Manual de utilizare

Sames 40C100 WB Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente