LG ARNU18GL5G4 Manual de utilizare

Original instruction

INSTALLATION MANUAL

AIR

CONDITIONER

P/NO : MFL68507211

Rev.00_042819

www.lg.com

РУССКИЙ ЯЗЫК

УКРАÏНСЬКА

ҚАЗАҚ ТІЛІ

БЕЛАРУСКАЯ МОВА

OʻZBEK TILI

ITALIANO

ESPAÑOL

FRANÇAIS

DEUTSCH

ΕΛΛΗΝΙΚΆ

ČEŠTINA

N

E

D

E

R

L

AND

S

POLSKI

LIMBA ROMÂNĂ

ENGLISH

ARNU05GL4G4 ARNU07GL4G4 ARNU09GL4G4 ARNU12GL5G4

ARNU15GL5G4 ARNU18GL5G4 ARNU21GL6G4 ARNU24GL6G4

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring

standards by authorized personnel only.

Please retain this installation manual for future reference after reading it thoroughly.

Ceiling Concealed Duct - Low Static

[

Representative

] LG Electronics Inc. EU Representative : LG Electronics European Shared

Service Center B.V. Krijgsman 1, 1186 DM Amstelveen, The Netherlands

[Manufacturer] LG Electronics Tianjin Appliances Co.,Ltd.

No.09, JinWei Road,Beichen District,Tianjin,300402.P.R.China

2 Indoor Unit

Ceiling Concealed Duct - Low Static Type Indoor Unit Installation Manual

TABLE OF CONTENTS

 Four type "A" screws

 Connecting cable

 Pipes: Gas side

Liquid side

(Refer to Product

Data)

 Insulation materials

 Additional drain pipe

 Level gauge

 Screw driver

 Electric drill

 Hole core drill

 Flaring tool set

 Specified torque wrenches

(different depending on model No.)

 Spanner.......Half union

 A glass of water

 Screw driver

 Hexagonal wrench

 Gas-leak detector

 Vacuum pump

 Gauge manifold

 Owner's manual

 Thermometer

Features...................................3

Safety Precautions.................4

Installation...............................9

Selection the best location....9

Ceiling opening dimension

and hanging bolt location....10

Indoor Unit Installation.........11

Wiring Connection ...............11

Checking the Drainage .......12

Indoor Unit Drain Piping......13

Dip Switch Setting ...............15

Group Control Setting .........16

Model Designation ..............21

Airborne Noise Emission ....21

Limiting concentration .........21

How to Set E.S.P?................22

Installation Requirements

Required Parts Required Tools

Installation Manual 3

Feature

ENGLISH

Features

Name Drain hose Clamp metal

Washer for

hanging bracket

Clamp

(Tie Wrap)

Insulation for

fitting

Quantity

1 EA 2 EA 8 EA 4 EA 1 SET

Shape

(Other)

• Owner's manual

•

Installation manual

for gas pipe

for liquid pipe

Installation Tool

Air Outlet Vents

Air Filter

Control Box

Air Intake Vents

Wired Remote Controller

Safety Precautions

4 Indoor Unit

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be

followed.

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is

classified

by the following indications.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Meanings of symbols used in this manual are as shown below.

Be sure not to do.

Be sure to follow the instruction.

WARNING

Installation

• Do not use a defective or underrated circuit breaker. Use this appliance

on a dedicated circuit.

- There is risk of fire or electric shock.

• For electrical work, contact the dealer, seller, a qualified electrician, or an

Authorized Service Center.

- Do not disassemble or repair the product. There is risk of fire or electric

shock.

• Always ground the product.

- There is risk of fire or electric shock.

• Install the panel and the cover of control box securely.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric shock

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

• Do not modify or extend the power cable.

- There is risk of fire or electric shock.

• Do not install, remove, or re-install the unit by yourself (customer).

- There is risk of fire, electric shock, explosion, or injury.

• Be cautious when unpacking and installing the product.

The following symbols are displayed on indoor and outdoor units.

Read the precautions in this manual

carefully before operating the unit.

This appliance is filled with flammable

refrigerant (R32)

This symbol indicates that the Operation

Manual should be read carefully.

This symbol indicates that a service

personnel should be handling this

equipment with reference to the

Installation Manual.

Installation Manual 5

Safety Precautions

ENGLISH

- Sharp edges could cause injury. Be especially careful of the case

edges and the fins on the condenser and evaporator.

• For installation, always contact the dealer or an Authorized Service

Center.

- There is risk of fire, electric shock, explosion, or injury.

• Do not install the product on a defective installation stand.

- It may cause injury, accident, or damage to the product.

• Be sure the installation area does not deteriorate with age.

- If the base collapses, the air conditioner could fall with it, causing

property damage, product failure, and personal injury.

• Do not turn on the breaker or power under condition that front panel,

cabinet, top cover, control box cover are removed or opened.

- Otherwise, it may cause fire, electric shock, explosion or death.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or

air purge. Do not compress air or Oxygen and Do not use Flammable

gases. Otherwise, it may cause fire or explosion.

- There is the risk of death, injury, fire or explosion.

Operation

• Do not let the air conditioner run for a long time when the humidity is

very high and a door or a window is left open.

- Moisture may condense and wet or damage furniture.

• Take care to ensure that power cable could not be pulled out or

damaged during operation.

- There is risk of fire or electric shock.

• Do not place anything on the power cable.

- There is risk of fire or electric shock.

• Do not plug or unplug the power supply plug during operation.

- There is risk of fire or electric shock.

• Do not touch(operate) the product with wet hands.

- There is risk of fire or electrical shock.

• Do not place a heater or other appliances near the power cable.

- There is risk of fire and electric shock.

• Do not allow water to run into electric parts.

- It may cause

There is risk of fire, failure of the product, or electric shock.

• The appliance shall be stored in a well-ventilated area where the room

size corresponds to the room area as specified for operation.(for R32)

Safety Precautions

6 Indoor Unit

• Do not store or use flammable gas or combustibles near the product.

- There is risk of fire or failure of product.

• Do not use the product in a tightly closed space for a long time.

- Oxygen deficiency could occur.

• When flammable gas leaks, turn off the gas and open a window for

ventilation before turn the product on.

- Do not use the telephone or turn switches on or off. There is risk of

explosion or fire.

• If strange sounds, or small or smoke comes from product. Turn the

breaker off or disconnect the power supply cable.

- There is risk of electric shock or fire.

• Stop operation and close the window in storm or hurricane.

If possible, remove the product from the window before the hurricane

arrives.

- There is risk of property damage, failure of product, or electric shock.

• Do not open the inlet grill of the product during operation.

(Do not touch the electrostatic filter, if the unit is so equipped.)

- There is risk of physical injury, electric shock, or product failure.

• When the product is soaked (flooded or submerged), contact an

Authorized Service Center.

- There is risk of fire or electric shock.

• Be cautious that water could not enter the product.

- There is risk of fire, electric shock, or product damage.

• Ventilate the product from time to time when operating it together with a

stove, etc.

- There is risk of fire or electric shock.

• Turn the main power off when cleaning or maintaining the product.

- There is risk of electric shock.

• When the product is not be used for a long time, disconnect the power

supply plug or turn off the breaker.

- There is risk of product damage or failure, or unintended operation.

• Take care to ensure that nobody could step on or fall onto the outdoor unit.

- This could result in personal injury and product damage.

• When mechanical connectors are reused indoors, sealing parts shall

be renewed.(for R32)

• When flared joints are reused indoors, the flare part shall be refabricated.

(for R32)

Installation Manual 7

Safety Precautions

ENGLISH

CAUTION

Installation

• Always check for gas (refrigerant) leakage after installation or repair of

product.

- Low refrigerant levels may cause failure of product.

• Install the drain hose to ensure that water is drained away properly.

- A bad connection may cause water leakage.

• Keep level even when installing the product.

- To avoid vibration or water leakage.

• Do not install the product where the noise or hot air from the outdoor

unit could damage the neighborhoods.

- It may cause a problem for your neighbors.

• Use two or more people to lift and transport the product.

- Avoid personal injury.

• Do not install the product where it will be exposed to sea wind (salt

spray) directly.

- It may cause corrosion on the product. Corrosion, particularly on the

condenser and evaporator fins, could cause product malfunction or

inefficient operation.

Operation

• Do not expose the skin directly to cool air for long periods of time.

(Don't sit in the draft.)

- This could harm to your health.

• Do not use the product for special purposes, such as preserving foods,

works of art, etc. It is a consumer air conditioner, not a precision

refrigeration system.

- There is risk of damage or loss of property.

• Do not block the inlet or outlet of air flow.

- It may cause product failure.

• Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.

- There is risk of fire, electric shock, or damage to the plastic parts of

the product.

• Any person who is involved with working on or breaking into a refrigerant

circuit should hold a current valid certificate from an industry-accredited

assessment authority, which authorises their competence to handle refr-

igerants safely in accordance with anindustry recognised assessment

specification.(for R32)

Safety Precautions

8 Indoor Unit

• Do not touch the metal parts of the product when removing the air filter.

They are very sharp!

- There is risk of personal injury.

• Do not step on or put anyting on the product. (outdoor units)

- There is risk of personal injury and failure of product.

• Always insert the filter securely. Clean the filter every two weeks or

more often if necessary.

- A dirty filter reduces the efficiency of the air conditioner and could

cause product malfunction or damage.

• Do not insert hands or other objects through the air inlet or outlet while

the product is operated.

- There are sharp and moving parts that could cause personal injury.

• Do not drink the water drained from the product.

- It is not sanitary and could cause serious health issues.

• Use a firm stool or ladder when cleaning or maintaining the product.

- Be careful and avoid personal injury.

• Replace the all batteries in the remote control with new ones of the

same type. Do not mix old and new batteries or different types of

batteries.

- There is risk of fire or explosion.

• Do not recharge or disassemble the batteries. Do not dispose of

batteries in a fire.

- They may burn or explode.

• If the liquid from the batteries gets onto your skin or clothes, wash it

well with clean water. Do not use the remote if the batteries have

leaked.

- The chemicals in batteries could cause burns or other health hazards.

• If you eat the liquid from the batteries, brush your teeth and see doctor.

Do not use the remote if the batteries have leaked.

- The chemicals in batteries could cause burns or other health hazards.

• Servicing shall only be performed as recommended by the equipment

manufacturer. Maintenance and repair requiring the assistance of

other skilled personnel shall be carried out under the supervision of

the person competent in the use of flammable refrigerants. (for R32)

Installation Manual 9

Installation

ENGLISH

Installation

Indoor unit

Install the air conditioner in the location that satisfies the fol-

lowing conditions.

• The place shall easily bear a load exceeding four times the

indoor unit’s weight.

• The place shall be able to inspect the unit as the figure.

• The place where the unit shall be leveled.

• The place shall easily connect with the outdoor unit.

• The place where the unit is not affected by an electrical

noise.

• The place where air circulation in the room will be good.

• There should not be any heat source or steam near the

unit

Confirm the positional relationship between the unit and

suspension bolts.

• Installation the ceiling opening to clean the filter or service

under the product.

Selection of the best location

A(Min)

Inspection hole

(600 x 600)

Control box

H=20 or more

• Suitable dimension "H" is necessary to get a slope

to drain as shown in the figure

Side view

(unit: mm)

600

B

B(Min)

(Unit: mm)

Top view

Air outlet

(Unit: mm)

Capacity (kBtu/h) A B

5/7/9 600 800

12/15/18 600 1000

21/24 600 1200

- The appliance shall be installed, operated and stored in a room

with a floor area larger than the minimum area.

- Use the graph of table to determine the minimum area.

Minimum floor area

0

100

200

300

400

500

600

Amin (m

2

)

m (kg)

0 1.224 2 3 4 5 6 7 8

Floor standing

Wall mounted

Ceiling mounted

(for R32)

Ceiling

Service Space

A

B

10 Indoor Unit

Installation

Ceiling dimension and hanging bolt location

Installation of Unit

Install the unit above the ceiling correctly.

• Apply a joint-canvas between the unit and duct to absorb

unnecessary vibration.

• Apply a filter Accessory at air return hole.

※ Install the unit leaning to a drainage hole

side as a figure for easy water drainage.

• A place where the unit will be leveled and that can support

the weight of the unit.

• A place where the unit can withstand its vibration.

• A place where service can be easily performed.

POSITION OF SUSPENSION BOLT

(Unit:mm)

Dimension

Capacity(kBtu/h)

A B C D E F G H I J

L4

733 772 338 460 36 190 20 660 148 700

L5

933 972 338 460 36 190 20 860 148 900

L6

1133 1172 338 460 36 190 20 1060 148 1100

C

E

G

D

F

I

A

J

B

M10 Nut

M10 washer

X 4

M10 Nut

M10 washer

X 4

X 8

H

Drainage hole

POSITION OF CONSOLE BOLT

- m : Total refrigerant amount in the system

- Total refrigerant amount : factory refrigerant charge + additional refrigerant amount

- Amin : minimum area for installation

Floor location

m (kg) Amin (m

2

)

< 1.224

-

1.224

12.9

1.4 16.82

1.6 21.97

1.8 27.80

2 34.32

2.2 41.53

2.4 49.42

2.6 58.00

2.8 67.27

3 77.22

3.2 87.86

3.4 99.19

3.6 111.20

3.8 123.90

4 137.29

4.2 151.36

4.4 166.12

Floor location

m (kg) Amin (m

2

)

4.6 181.56

4.8 197.70

5 214.51

5.2 232.02

5.4 250.21

5.6 269.09

5.8 288.65

6 308.90

6.2 329.84

6.4 351.46

6.6 373.77

6.8 396.76

7 420.45

7.2 444.81

7.4 469.87

7.6 495.61

7.8 522.04

Wall mounted

m (kg) Amin (m

2

)

< 1.224

-

1.224

1.43

1.4 1.87

1.6 2.44

1.8 3.09

2 3.81

2.2 4.61

2.4 5.49

2.6 6.44

2.8 7.47

3 8.58

3.2 9.76

3.4 11.02

3.6 12.36

3.8 13.77

4 15.25

4.2 16.82

4.4 18.46

Wall mounted

m (kg) Amin (m

2

)

4.6 20.17

4.8 21.97

5 23.83

5.2 25.78

5.4 27.80

5.6 29.90

5.8 32.07

6 34.32

6.2 36.65

6.4 39.05

6.6 41.53

6.8 44.08

7 46.72

7.2 49.42

7.4 52.21

7.6 55.07

7.8 58.00

Ceiling Mounted

m (kg) Amin (m

2

)

< 1.224

-

1.224

0.956

1.4 1.25

1.6 1.63

1.8 2.07

2 2.55

2.2 3.09

2.4 3.68

2.6 4.31

2.8 5.00

3 5.74

3.2 6.54

3.4 7.38

3.6 8.27

3.8 9.22

4 10.21

4.2 11.26

4.4 12.36

Ceiling Mounted

m (kg) Amin (m

2

)

4.6 13.50

4.8 14.70

5 15.96

5.2 17.26

5.4 18.61

5.6 20.01

5.8 21.47

6 22.98

6.2 24.53

6.4 26.14

6.6 27.80

6.8 29.51

7 31.27

7.2 33.09

7.4 34.95

7.6 36.86

7.8 38.83

Installation Manual 11

Installation

• Select and mark the position for fixing bolts.

•

Drill the hole for set anchor on the face of ceil-

ing.

• Insert the set anchor and washer onto the sus-

pension bolts for locking the suspension bolts

on the ceiling.

•

Mount the suspension bolts to the set anchor firmly.

• Secure the installation plates onto the suspen-

sion bolts (adjust level roughly) using nuts,

washers and spring washers.

1 Set anchor

Old building New building

2 Plate washer

3 Spring washer

4 Nut

5 Suspension

bolts

Connect the wires to the terminals on the control board individually according to the outdoor unit connec-

tion.

• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of indoor

unit respectively.

Clamping of cables

1) Arrange 2 power cables on the control panel.

2) First, fasten the steel clamp with a screw to the inner boss of control panel.

3) For the cooling model, fix the other side of the clamp with a screw strongly. For the heat pump

model, put the 0.75mm

2

cable(thinner cable) on the clamp and tighten it with a plastic clamp to

the other boss of the control panel.

Wiring Connection

Indoor Unit Installation

CAUTION : Tighten the nut and bolt

to prevent unit falling.

WARNING : Make sure that the screws of the terminal are free from looseness.

CAUTION : The Power cord connected to the unit should be selected according

to the following specifications.

Terminal Block Indoor Terminal Block Indoor

INDOOR POWER INPUT

Outdoor unit

Indoor unit

Central controller

Outdoor unitIndoor unit

12V

Installation

12 Indoor Unit

1. Remove the Air Filter.

2. Check the drainage.

• Spray one or two glasses of water upon the

evaporator.

• Ensure that water flows drain hose of indoor

unit without any leakage.

Checking the Drainage

.

CAUTION

(for R32)

• When mechanical connectors are reused indoors, sealing parts shall be renewed.

• When flared joints are reused indoors, the flare part shall be re-fabricated.

Installation Manual 13

Installation

CAUTION

Ceiling

Drain Pump use

Drainage hole

Front of view

1. Install declination of the indoor unit is very important for the drain of the duct type air conditioner.

2. Minimum thickness of the insulation for the connecting pipe shall be 19mm.

• The unit must be horizontal or declined to the drain hose connected when finished

installation.

• Drain piping must have down-slope (1/50 to 1/100): be sure

not to provide up-and-down slope to prevent reversal flow.

• During drain piping connection, be careful not to exert extra

force on the drain port on the indoor unit.

• The outside diameter of the drain connection on the indoor

unit is 32mm.

• Be sure to install heat insulation on the drain piping.

Piping material: Polyvinyl chloride pipe VP-25 and

pipe fittings

The air conditioner uses a drain pump to drain water.

Use the following procedure to test the drain pump operation:

• Connect the main drain pipe to the exterior

and leave it provisionally until the test

comes to an end.

• Feed water to the flexible drain hose and

check the piping for leakage.

• Be sure to check the drain pump for normal

operating and noise when electrical wiring

is complete.

• When the test is complete, connect the

flexible drain hose to the drain port on the

indoor unit.

Heat insulation material: Polyethylene foam with thick-

ness more than 8 mm.

Drain test

Upward

routing

not allowed

Pipe clamp

Maintenance

drain port

Indoor unit

Drain Piping

Feed water

Drain Pump

Drain pan

Flexible drain hose

Main

drain pipe

Glue the joint

Drain

port

Drain hose connection

Use the clip

Installation

14 Indoor Unit

CAUTION:

After the confirmation of the above conditions, prepare the wiring as follows:

1) Never fail to have an individual power specialized for the air conditioner. As

for the method of wiring, be guided by the circuit diagram posted on the inside

of control box cover.

2) Provide a circuit breaker switch between power source and the unit.

3) The screws which fasten the wiring in the casing of electrical fittings are liable

to come loose from vibrations to which the unit is subjected during the course

of transportation. Check them and make sure that they are all tightly fastened.

(If they are loose, it could give rise to burn-out of the wires.)

4) Specification of power source

5) Confirm that electrical capacity is sufficient.

6) Be sure that the starting voltage is maintained at more than 90 percent of the

rated voltage marked on the name plate.

7) Confirm that the cable thickness is as specified in the power sources specifi-

cation. (Particularly note the relation between cable length and thickness.)

8) Never fail to equip a leakage breaker where it is wet or moist.

9) The following troubles would be caused by voltage drop-down.

• Vibration of a magnetic switch, damage on the contact point, fuse breaking, distur-

bance by the normal function of an overload protection device.

• Proper starting power is not given to the compressor.

HAND OVER

Teach the customer the operation and maintenance procedures, using the operation manual.

(air filter cleaning, temperature control, etc.)

Installation Manual 15

Installation

Dip Switch Setting

For Multi V Models, DIP switch 1, 2, 6, 8 must be set OFF.

CAUTION

Function Description Setting Off Setting On Default

SW1 Communication N/A (Default) - - Off

SW2 Cycle N/A (Default) - - Off

SW3 Group Control

Selection of Master or

Slave

Master Slave Off

SW4

Dry Contact

Mode

Selection of Dry

Contact Mode

Wired/Wireless remote

controller

selection of Manual or Auto

operation Mode

Auto Off

SW5 Installation

Fan continuous

operation

Continuous operation Re-

moval

- Off

SW6 Heater linkage N/A - - Off

SW7

Ventilator link-

age

Selection of Ventilator

linkage

Linkage Removal Working

Off

Vane selection

(Console)

Selection of up/down

side Vane

Up side + Down side Vane

Up side Vane

Only

Region selec-

tion

Selection tropical re-

gion

General model

Tropical

model

SW8 Etc. Spare - - Off

1. Indoor Unit

2. Outdoor Unit

In case that the products meet specific conditions, “Auto addressing” function can start automatically

with the improved speed by turning the DIP switch #3 of the outdoor unit and resetting the power.

※ Specific conditions:

- All names of the indoor units are ARNU****4.

- The serial number of Multi V super IV (outdoor units) is after October 2013.

DIP switch 7 segment

Outdoor Unit PCB Outdoor Unit DIP Switch

Installation

16 Indoor Unit

Group Control Setting

Master

GND

Signal

12 V

LGAP Network System

Master Slave Slave Slave

Display Error Message

Only connect serial signal and GND lines

between indoor units.

or

1. Group Control 1



Wired remote controller 1 + Standard Indoor Units

Some products have no DIP switch on PCB. It is possible to set indoor units to Master or Slave by

using the wireless remote controller instead of DIP switch.

For the details of the setting, please refer to the manual of the wireless remote controller.

1. It is possible to 16 indoor units(Max.) by one wired remote controller.

Set only one indoor unit to Master, set the others to Slave.

2. It is possible to connect with every type of indoor units.

3. It is possible to use wireless remote controller at the same time.

4. It is possible to connect with Dry Contact and Central controller at the same time.

- The Master indoor unit is possible to recognize Dry Contact and Central Controller only.

5. In case that any error occurs at indoor unit, the error code is displayed on the wired remote

controller.

It is possible to control the other indoor units except the error units.



DIP Switch in PCB



Master Setting

- No. 3 Off



Slave Setting

- No. 3 On

Indoor Unit DIP Switch

Installation Manual 17

Installation

GND

Signal

12 V

LGAP Network System

Master Master Slave Slave

Donʼt connect serial 12V line

or

Display Error Message

Master Master

 It is possible to connect indoor units since Feb. 2009.

 It can be the cause of malfuctions when there is no setting of master and slave.

 In case of Group Control, it is possible to use following functions.

- Selection of operation, stop or mode

- Temperature setting and room temperature check

- Current time change

- Control of flow rate (High/Middle/Low)

- Reservation settings

It is not possible to use some functions.

 It is possible to control 16 indoor units(Max.) with the master wired remote control.

 Other than those, it is same with the Group Control 1.

2. Group Control 2



Wired remote controllers + Standard Indoor Units

Installation

18 Indoor Unit

GND

Signal

12 V

LGAP Network System

MN

Master

Slave

Display Error Message

Master

FAU

Slave

FAU

Master

or

Master Master

Display Error Message

FAU

Standard Standard

FAU FAU

Standard Standard

FAU

* FAU : Fresh Air Intake Unit

Standard: Standard Indoor Unit

 In case of connecting with standard indoor unit and Fresh Air Intake Unit, separate Fresh Air

Intake Unit with standard units. (N, M ≤ 16) (Because setting temperature are different.)

 Other than those, it is same with Group Control 1.

3. Group Control 3



Mixture connection with indoor units and Fresh Air Intake Unit

Installation Manual 19

Installation

LGAP Network System

Master

Slave

GND

Signal

12 V

or

Display Error Message

Master

Slave

4. 2 Remote Control



Wired remote controller 2 + Indoor unit 1

1. It is possible to connect two wired remote controllers (Max.) with one indoor unit.

Set only one indoor unit to Master, set the others to Slave.

Set only one wired remote controller to Master, set the others to Slave.

2. Every types of indoor unit is possible to connect two remote controller.

3. It is possible to use wireless remote controller at the same time.

4. It is possible to connect with Dry Contact and Central controller at the same time.

5. In case that any error occurs at indoor unit, the error code is displayed on the wired

remote controller.

6. There isnʼt limits of indoor unit function.

Installation

20 Indoor Unit

5. Accessories for group control setting

It is possible to set group control by using below accessories.

Indoor unit 2 EA +Wired remote controller

Indoor unit 1 EA +Wired remote controller 2EA



PZCWRCG3 cable used for connection



PZCWRC2 cable used for connection

Slave

Mas te r

PZCWRCG3

Mas te r S lav e

PZCWRC2

• Apply totally enclosed noncombustible conduit in case of local building code Requiring plenum

cable usage.

CAUTION

Pagina se încarcă ...

LG ARNU18GL5G4 Manual de utilizare

LG ARNU18GL5G4 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente