Smithco SweepStar 48H and 60 Instrucțiuni de utilizare

Gas and Diesel SweepStar 60

Model 76-000-D and 77-100-C

High Lift SweepStar 48

Model 48-500-A

August 2018

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

Operator’s

Englsih

Spanish

French

CONTENTS

Introduction ...........................................................................1-11

Introduction ...............................................................................1

Symbols ................................................................................ 2-3

Safety .................................................................................... 4-5

Safe Practices ...........................................................................6

Specications ....................................................................... 7-8

Setup ......................................................................................... 9

Controls & Instruments .................................................... 10-13

Service ................................................................................. 14-16

Operation .......................................................................... 14-15

Battery ..................................................................................... 16

Introducción ........................................................................S2-14

Introducción ............................................................................. S3

Símbolos .................................................................................. S4

Seguridad e Cauciones de Seguridad ..................................S5-6

Procedimientos seguros .......................................................... S7

Especicaciones .................................................................. S8-9

Instalación ............................................................................. S10

Controles e instrumentos ... ............................................. S11-14

Servicio ..............................................................................S15-17

Operación ..........................................................................S15-16

Batería .................................................................................... S17

Introduction ........................................................................... F3-1

Introduction .............................................................................. F3

Symboles ................................................................................. F4

Sécurité & Précautions ......................................................... F5-6

Méthodes pratiques de sécurité .............................................. F7

Caractéristiques ................................................................... F8-9

Préparation ............................................................................ F10

Commandes & Instruments ............................................. F12-15

Service courant ................................................................. F16-18

Fonctionnement ................................................................ F16-17

Batterie .................................................................................. F18

Autres ..................................................................................... F19

Declaration of Conformity - Déclaration de conformité .... F19-24

Warranty- Garantia -Garantie ......................................................

1

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

WARNING

Failure to follow cautious operating practices can re-

sult in serious injury to the operator or other persons.

The owner must understand these instructions, and

must allow only trained persons who understand these

instructions to operate this vehicle.

WARNING:

Engine exhaust and some of its constituents are

known to the State of California to cause cancer,

birth defects, and other reproductive harm.

For more information visit

www.P65Warning.ca.gov

INTRODUCTION

Thank you for purchasing a Smithco product.

Read this manual and all other manuals pertaining to the Sweeper carefully as they contain safety, operating,

assembly and maintenance instructions. Failure to do so could result in personal injury or equipment damage.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides

are from the operator’s seat, facing forward.

All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. Refer to engine manual for placement of engine serial number.

For product and accessory information, help nding a dealer, or to register your procuct please contact us at

www.Smithco.com.

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts

For easy access record your Serial and Model numbers here.





2

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

20° MAX

Read Operator’s

Manual

Engine Stop

Engine Start

Engine Run

Engine Oil

Water

Temperature

RPM

Gasoline

Diesel

Glow Plug

Hour Meter

Hand Throttle

Choke

Hydraulic

Oil Level

Ground Speed

Park Brake

Release

Lift Arm

Slow

Moving Parts

Pinch Point

Hydraulic Fluid

Penetration

Warning

Danger

Caution

Fast

Rollover

Danger

Hot Surface

Headlamp

Seat Belt

No Riders

Blower

3

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY

Read and understand this manual and all safety signs before operating and maintaining. Review the safety

instructions and precautions annually.

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL

YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF

OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The

appropriate signal word for each has been selected using the following guidelines:

DANGER: Red. Indicates an imminently hazardous

situation that, if not avoided, will result in death or serious

injury. This signal word is to be limited to the most ex-

treme situations typically for machine components which,

for functional purposes, cannot be guarded.

WARNING: Orange. Indicates a potentially hazardous

situation that, if not avoided, could result in death or seri-

ous injury, and includes hazards that are exposed when

guards are removed. It may also be used to alert against

unsafe practices.

CAUTION: Yellow. Indicates a potentially hazardous

situation that, if not avoided, may result in minor or mod-

erate injury. It may also be used to alert against unsafe

practices.

IMPORTANT: Blue. Indicates procedures which should

be

followed to avoid damage to the machine.

4

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY PRECAUTIONS

Connecting battery cables to the wrong post could result in personal injury

and/or damage to electrical system. Make sure battery and cables do not

interfere or rub on any moving part. Connect red positive (+) cable to battery

rst. When disconnecting remove black negative (-) cable rst.

Fuel is ammable. Caution must be used when storing or handling it. Do not

ll fuel tank while engine is running or in an enclosed area. Fumes are explo-

sive and dangerous to inhale. DO NOT SMOKE while lling fuel tank. DO NOT

OVERFILL.

Before servicing or making adjustments to machine, stop engine and remove

key from ignition.

Follow all procedures and ONLY use parts prescribed by the manufacturer.

Read the engine manual before maintenance.

Battery Electrolyte is an acidic solution and should be handled with care. If

electrolyte is splashed on any part of your body, ush all contact areas imme-

diately with liberal amounts of water. Get medical attention immediately.

Use of booster battery and jumper cables. Particular care should be used

when connecting a booster battery. Use proper polarity in order to prevent

sparks.Safety Precautions.

REMEMBER: If Safety Signs have been damaged, removed, become illegible

or parts replaced without decals, new decals must be applied. New decals are

available from your authorized distributor or factory.

5

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine (engine, accessories

and attachments).

2. Never allow anyone to operate or service the machine or its attachments without proper training and instructions.

Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before you operate

the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears, hands and

feet. Operate the machine only in daylight or in good articial light.

5. Inspect the area where the equipment will be used. Beware of overhead obstructions and underground obstacles.

Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other protective

devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without proper ventila-

tion.

9. Fuel is highly ammable, handle with care.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. After engine has started, machine must not move. If movement is evident, the neutral mechanism is not adjusted

correctly. Shut engine off and readjust so the machine does not move when in neutral position.

13. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and cause seri-

ous injury.

14. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not operate on a slope greater than 10°. Pay careful attention to the inclinometer on you machine.

C. Do not stop or start suddenly on sloped surfaces.

D. Reduce speed on slopes and in all turns. Use caution when changing directions on all surfaces.

E. Do not change directions of travel on any slope.

F. Do not operate debris hopper lift or tailgate while on slopes.

G. Stay alert for holes in the terrain and other hidden hazards.

15. Before leaving operator’s position for any reason:

A. Disengage all drives.

B. Lower all attachments to the ground.

C. Set park brake.

D. Shut engine off and remove the ignition key.

16. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean, adjust or

service the machine.

17. Keep the area of operation clear of all bystanders.

18. Never carry passengers.

19. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

20. Use parts and materials supplied by SMITHCO only. Do not modify any function or part.

21. Do not remove the radiator cap when the engine is hot. When cooled, loosen cap slightly to the stop to relieve any

pressure before removing the cap completely.

These machines are intended for operation by well trained persons performing professional maintenance on golf

courses, sports turf, and any other area maintained turf and related trails, paths and lots. No guaranty as to the

suitability for any task is expressed or implied.

6

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SPECIFICATIONS FOR SWEEP STAR 60 GAS & DIESEL

WEIGHTS AND DIMENSIONS

Length 129" (328 cm)

Width 74.5" (179 cm)

Height with Hopper Down 82" (208 cm)

Height with Hopper Up 127" (323 cm)

Wheel Base 68.5" (174 cm)

Weight 2200 lbs (998 kg)

ROLL OVER PROTECTION BAR

Standard on all Machines

SOUND LEVEL GAS ENGINE DIESEL ENGINE

At ear level 92 dB 98 dB

At 3 ft (0.914 m) 86 dB 96 dB

At 30 ft (9.14 m) 64 dB 74 dB

ENGINE GAS DIESEL

Make Briggs & Stratton Kubota

Model# 543477 D 722 E3B

Type / Spec# 0175G1

Horsepower 31 Hp (23 kw) 18.8 Hp (14 kw)

Fuel Unleaded 87 Octane Gasoline Minimum

No. 2-D, S500: Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%

No.2-D, S15: Ultra Low Sulfur Diesel (ULSD) less than 15 ppm or 0.0015 wt.%

Cooling System Air Cooled Liquid Cooled

Lubrication System Full Pressure Full Pressure

Alternator 20 Amp 40 Amp

Tire & Wheels Front: One 18 x 9.50 x 8 Multi-rib (20 psi; 1.4 bar)

Front tire and wheel uid lled to 50 lbs. total. 28 pints of windshield washer

uid or equivalent.

Rear: Two 24 x 13.00 x 12 Super Soft (18 psi; 1.3 bar)

Castor: 9 x 3.5 - 4 (20 psi; 1.4 bar)

SPEED

Forward Speed 0 to 12 m.p.h. (0-19 kph)

Reverse Speed 0 to 4 m.p.h. (0-6 kph)

BATTERY Automotive type 45 -12 volt

BCI Group Size 45

Cold Cranking Amps 480 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 9" (23 cm)

Maximum Width 5.38" (14 cm)

Maximum Height 9" (23 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual See Engine Manual

Fuel 6 gallons (22,7 liters) 5 gallon (19 liters)

Hydraulic Fluid 5 gallon (19 liters) 5 gallon (19 liters)

Cooling 1 gallon (3.8 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

7

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SPECIFICATIONS FOR SWEEP STAR 48 HIGH LIFT

WEIGHTS AND DIMENSIONS HIGH LIFT

Length 121" (307 cm)

Width 60" (153 cm)

Height with Hopper Down 63" (160 cm)

Height with Hopper Up 126" (320 cm)

Wheel Base 70" (179 cm)

Weight 1900 lb (862 kg)

SOUND LEVEL

At ear level 90 dB

ENGINE

Make Briggs & Stratton

Model# 356447

Type / Spec# 0263G1

Horsepower 18 Hp (13kW)

Fuel Unleaded 87 Octane Gasoline Minimum

Cooling System Air Cooled

Lubrication System Full Pressure

Alternator 16 Amp

WHEELS & TIRE Front: One 18 x 9.50 x 8 Multi-rib (20 psi (1.4 bar))

Rear: Two 22 x 11.00 - 10 4-ply (20 psi (1.4 bar))

Castor: 9 x 3.50 - 4 (20 psi (1.4 bar))

SPEED

Forward Speed 0 to 10 m.p.h. (0-16 kph)

Reverse Speed 0 to 4 m.p.h. (0-6 kph)

BATTERY Automotive IBS type 45-12 volt

BCI Group Size 45

Cold Cranking Amps 480 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 9" (23 cm)

Maximum Width 5.38" (14 cm)

Maximum Height 9" (23 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 6 gallon (22,7 liters)

Hydraulic Fluid 5 gallon (19 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

8

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP

The Sweep Star arrives from Smithco setup and ready for service.

1. Set park brake.

2. Check the tire pressure. Sweep Star 60: The front tire and castor wheels are 20 psi (1.4 bar) and the

rear tires are 18 psi (1.3 bar). Sweep Star 48: All tires and castor wheels are 20 psi (1.4 bar). All are

maximum pressures.

3. Check the installation of the battery, which is located

below the seat. This is a negative grounding system.

Connecting battery cables to the wrong post could result

in personal injury and/or damage

to the electrical system. Make

sure battery and cables do not

interfere or rub on any moving

part. Connect the red positive(+) cable (A) to the

battery rst. When disconnecting remove the

black negative(-) cable (B) rst.

4. Check the engine oil and add as necessary. The dip

stick is located under the seat directly behind the control

panel. Oil ll is located on top of valve cover, use SAE 10W-40 API Service SJ or higher motor oil. DO

NOT OVERFILL.

5. Fill fuel tank, located on right side, with Unleaded 87 Octane gasoline (minimum) for gas machines

and No.1-D or No. 2-D, S500: Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%; or No1-D or

No.2-D, S15: Ultra Low Sulfur Diesel (ULSD) less than 15 ppm or 0.0015 wt.%or diesel machines.

Fuel is ammable. Caution must be used when storing or handling it. Do not

ll fuel tank while engine is running or in an enclosed area. Fumes are explo-

sive and dangerous to inhale. DO NOT SMOKE while lling the fuel tank. DO

NOT OVERFILL.

6. Check hydraulic uid level in tank. Remove cap and add SAE 10W-40 API Service SJ or higher motor

oil if necessary. Fluid level should be about 2"-2

1

/

2

" (5 - 6.4 cm) from the top of the tank when cold.

7. Machine should be greased before starting. See Maintenance part of manual.

8. Read operating instructions before starting.

9

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

NOTES

10

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS SWEEP STAR 60 GAS SWEEPER

CONTROLS & INSTRUMENTS SWEEP STAR 60 DIESEL SWEEPER

11

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

A. Circuit Breaker - The circuit breaker is a re-settleable fuse. To reset push down on it.

B. Hour Meter - The hour meter indicates hours of machine operation. It operates only when the ignition

switch is on.

C. Ammeter - The ammeter indicates the rate of charging or discharging of battery.

D. Ignition Switch - The ignition switch has three positions: Off - Run - Start.

E. Hand Throttle - The hand throttle is used to regulate engine speed.

F. Choke - The choke is used in starting the engine. Pull choke out to close choke plate when starting a

cold engine. Push in when engine starts. A warm engine may not require "choking" to start.

G. Reel Lift Lever - The reel lift lever is used raise and lower the reel. Pull back to raise the reel. Push

forward to lower the reel.

H. Hopper Lift Lever - The hopper lift lever is used to raise and lower the hopper. Pull back to raise the

hopper. Push forward to lower the hopper.

I. Tailgate Lever - The tailgate lever is used to open and close the tailgate. Pull back to open the tailgate.

Push forward to close the tailgate. Tailgate tends to creep open while sweeping. Frequently close the

tailgate to ensure no creeping.

J. Park Brake - The park brake is only a parking brake. Pull back to release, push forward to apply.

K. Oil Light - The oil light should come on when the ignition is on without the engine running and go out

when the engine is running. The oil light will light when the oil pressure is low. If oil light should come

on, shut engine off immediately and nd the cause.

L. Charge Light - The charge light should come on when the ignition is on, without the engine running.

When the engine is running the light should go out. The charge light will light when the charging system

is not charging. If the charge light should come on, shut engine off and nd cause.

M. Temperature Light - Temperature light will come on and a buzzer will sound when the engine starts to

overheat.

N. Glow Plug Indicator Light - When key is turned counter clockwise to "Preheat" the light will light. When it

goes out the engine is ready to start.

O. Stop Knob - The stop knob is used to start the engine. The knob must be pulled out to start and run the

engine. Push in to stop engine.

P. Electric Clutch - Controls the reel electrically. Move the switch to the left and the reel will disengage. If

moved to the right reel will engage. NOTE: Electric clutch must be disengaged before starting.

Q. Inclinometer - Indicates machine tilt on side hill. DO NOT EXCEED

10°.

12

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS SWEEP STAR 48 HSWEEPER

13

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

A. Hour Meter - The hour meter indicates hours of machine operation. It operates only when the ignition

switch is on.

B. Ignition Switch - The ignition switch has three positions: Off - Run - Start.

C. Hand Throttle - The hand throttle is used to regulate engine speed.

D. Reel Lift Lever - The reel lift lever is used raise and lower the reel. Pull back to raise the reel. Push

forward to lower the reel.

E. Hopper Lift Lever - The hopper lift lever is used to raise and lower the hopper. Pull back to raise the

hopper. Push forward to lower the hopper.

F. Tailgate Lever - The tailgate lever is used to open and close the tailgate. Pull back to open the tailgate.

Push forward to close the tailgate. Tailgate tends to creep open while sweeping. Frequently close the

tailgate to ensure no creeping.

G. Oil Light - The oil light should come on when the ignition is on without the engine running and go out

when the engine is running. The oil light will light when the oil pressure is low. If oil light should come

on, shut engine off immediately and nd the cause.

H. Electric Clutch - Controls the reel electrically. Move the switch to the left and the reel will disengage. If

moved to the right reel will engage. NOTE: Electric clutch must be disengaged before starting.

I. Inclinometer - Indicates machine tilt on side hill. DO NOT EXCEED 10°.

J. Choke - The choke is used in starting the engine. Pull choke out to close choke plate when starting a

cold engine. Push in when engine starts. A warm engine may not require "choking" to start.

14

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

Before operating this machine, become familiar with all controls and functions of these units. Also complete all

maintenance requirements and read all safety warnings. By knowing the machine thoroughly, how it operates

and by doing the prescribed maintenance steps, you can expect relatively trouble-free operation for years to

come.

Beater reel MUST BE DISENGAGED before starting engine.

STARTING GAS ENGINE

1. Make sure the fuel ow valve, located on the fuel tank, is “ON.”

2. The ignition switch is located on control panel. Insert key (A) and turn

clockwise until engine starts (C). Release key and it will return to run

position (B). Use choke and hand throttle as necessary.

3. Allow engine to idle and warm up a few minutes before selecting a direc-

tion of travel.

STARTING DIESEL ENGINE

1. Make sure the fuel ow valve, located on the fuel tank, is “ON.” Also the

fuel valve, located on the fuel lter, is “ON.”

2. Pull the stop knob out, located on the control panel.

3. Place the speed control lever at more than half “Operation.”

4. Insert the key (A) into the key switch and turn it to “ON” (B). Check to

see if the oil pressure lamp and charge lamp are lit.

5. Turn the key counter clockwise to “preheat” (D) until the indicator lamp

on the control panel goes out.

6. Turn the key clockwise to “Start” (C). When engine starts, release the

key immediately. Do not hold the key in the “Start” position for more than

10 seconds.

7. Check to see that the oil pressure and charge lamps are off. If the lamps are still on, immediately stop

the engine (push the stop knob in) and determine the cause.

8. Warm up the engine at medium speed without load.

TAILGATE LEVER

Tailgate tends to creep open while sweeping. Frequently close the tailgate to ensure no creeping.

SWEEP STAR 60 ACCELERATOR/REVERSE PEDAL

On the right oorboard of the Sweep Star 60 is a "rocker" pedal.

Push down on the front (G) with your foot and the machine will

accelerate. Push down on the rear of the pedal (H) with the heel

of your foot and the machine will go in reverse. The machine is in

neutral when foot is off the pedal.

15

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

SWEEP STAR 48H ACCELERATOR/REVERSE PEDAL

On the right oorboard of the Sweep Star 48H is the accelerator

pedal (J) and the reverse pedal (K). The machine is in neutral when foot

is off the pedal.

DAILY CHECKLIST

1. Check park brake adjustment. Adjust as required.

2. Check engine oil level. Add as needed. DO NOT OVERFILL.

3. Tire pressure should be 20 psi (1.4 bar) on all Sweep Star 48 tires

and castor wheels. Tire pressure should be 20 psi (1.4 bar) on

Sweep Star 60 front tire and castor wheel, 18 psi (1.3 bar) on rear

tires.

4. Inspect electrical system for loose connections or frayed wiring,

including battery cables. Replace any faulty equipment or tighten if

loose.

5. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.

6. Inspect hydraulic lines for damage or leaks. Never use hands to inspect leaks.

7. Check hydraulic oil level in right side tank. The level should be 2" to 2

1

/

2

" (5-6.4 cm) from top of tank

when uid is cold. If level is low, add SAE 10W-40 API Service SJ or higher motor oil.

8. Inspect steering, throttle and shift linkages for good hookups and clear travel.

9. Check controls for smooth, proper working operation. Lubricate as needed.

10. Check and clean all debris from engine compartment.

HOPPER LIFT SAFETY ARM

Each machine is equipped with two Hopper Lift Safety Bar.

They are stored on the Hopper Dump arms, on each side of

the hopper, with two bolts and wing nuts. See Picture 1.

The purpose of the Hopper Lift Safety Bar is to help the hop-

per lift cylinders hold the hopper in the up position. The weight

of the hopper can cause the cylinders to retract. Bolt the

Hopper Lift safety bar around the cylinder shaft to prevent the

hopper from slowly lowering due to gravity. See Picture 2.

Picture 1

Picture 2

16

English

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or

any ignited object to come near the battery. When charging or working near battery, always shield your eyes

and always provide proper ventilation.

Battery cable should be disconnected before using “Fast Charge”.

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended

charging rate. If electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp rst and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If

electrolyte is splashed on any part of your body, ush all contact areas imme-

diately with liberal amounts of water. Get medical attention immediately.

JUMP STARTING

Use of booster battery and jumper cables. Particular care should be used

when connecting a booster battery. Use proper polarity in order to prevent

sparks.

To jump start (negative grounded battery):

1. Shield eyes.

2. Connect ends of one cable to positive (+) termi-

nals of each battery, rst (A) then (B).

3. Connect one end of other cable to negative (-)

terminal of "good" battery (C).

4. Connect other end of cable (D) to engine block

on unit being started (NOT to negative (-) termi-

nal of battery)

To prevent damage to other electrical components on

unit being started, make certain that engine is at idle

speed before disconnecting jumper cables.

TOWING

When it is necessary to move the Sweep Star 48 without engine running, the bypass valve built into hydro-

static pump must be “open” by turning it counterclockwise. An “open” valve allows uid to pass through the

wheels freely. When normal, driven, operation is desired, valve should be closed by turning it clockwise. Fail-

ure to “close” the valve with engine running means no power to wheels. Tow slowly. 2 m.p.h. or less.

The bypass valve is a

3

/

8

diameter shaft with a

11

/

64

hole for inserting something for leverage so you can turn it.

On the high lift it is on the top of the hydrostatic. On the ground level dump it is on the bottom of the hydrostat-

ic.

The Smithco Commercial Products Two-Year Limited Warranty

Smithco, Inc. (Smithco) warrants your 2016 or newer Smithco Commercial Product (“Product”) purchased after

October 1, 2016 to be free from defects in materials or workmanship for the period of time listed below. Where a

warrantable condition exists, Smithco will repair the Product at no cost to you including diagnosis, labor (at the

Smithco standard labor rate, subject to the Smithco at rate schedule), and parts.

Warranty Duration is:

(1) Two years, 1500 operational hours* from the date of delivery to the original purchaser or Five years from

the date of original manufacturer of the product, whichever occurs rst. (*Products equipped with hour

meter).

(2) Products used in rental situations are covered for 90 days from date of delivery to original user/renter.

Owner Responsibilities:

As the Product owner, you are responsible for required maintenance and adjustments stated in your Owner’s Manual.

Failure to perform required maintenance and adjustments can be grounds for disallowing a warranty claim. You are

particularly responsible to train all present and future operators of this product on the safe operation of this

product at your location.

Instructions for Obtaining Warranty Service:

You are responsible for notifying the Authorized Smithco Products Distributor from whom you purchased the Product as

soon as you believe a warrantable condition exists and not later than 30 days from discovery of the condition.

If you need help locating an Authorized Smithco Distributor, or if you have questions regarding your warranty rights or

responsibilities, you may contact us at:

Smithco Product Support Department

200 West Poplar Ave.

Cameron, Wisconsin 54822

Telephone: 800-891-9435 E-Mail: [email protected]

Maintenance Parts:

Parts scheduled for replacement as required maintenance (“Maintenance Parts”), are warranted for the period of time up

to the scheduled replacement time for that part.

Items/Conditions Not Covered:

Not all product failures or malfunctions that occur during the warranty period are defects in materials or workmanship.

The items/conditions listed below are not covered by this warranty:

Product failures which result from the use of non-Smithco replacement parts, or from installation and use of add-

on, modied, or unapproved accessories are not covered.

Product failures which result from failure to perform required maintenance and/or adjustments are not covered.

Product failures that result from operating the Product in an abusive, negligent or reckless manner are noT

covered.

This warranty does not apply to parts subject to consumption through use, unless found to be defective.

Examples of parts which are consumed, or used up, during normal Product operation include, but are not limited

to: blades, tines, teeth, scariers, rakes, plates, wear plates, castor wheels, tires, batteries, lters, belts, nozzles,

etc.

This warranty does not apply to failures caused by outside inuence. Items considered to be outside inuence

include, but are not limited to, weather, storage practices, contamination, use of unapproved coolants, lubricants,

additives, or chemicals, etc.

This warranty does not apply to normal “wear and tear” items. Normal “Wear and Tear” includes, but is not limited

to, damage to seats due to wear or abrasion, worn painted surfaces, scratched decals or windows, etc.

Smithco may require the return of failed parts or components in order to determine the validity of any warranty

claim.

Smithco will not be obligated to replace components of other manufacturers if inspection by the original

component manufacturer indicates that failure was due to normal wear and tear, expected consumption through

use or improper care or service.

Other Legal Disclaimers:

The above remedy for product defects through repair or replacement by an authorized Smithco distributor or dealer is the

purchaser’s sole remedy for any defect. This warranty gives you specic legal rights, and you may also have other rights

which vary from state to state.

THERE ARE NO OTHER EXPRESS WARRANTIES OTHER THAN THOSE SET FORTH ABOVE. ALL IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE DURATION OF THE

LIMITED WARRANTIES CONTAINED HEREIN.

Some states may not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to

you.

THE SMITHCO COMPANY IS NOT LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES IN CONNECTION WITH THE USE OF THE PRODUCT, INCLUDING ANY COST OR EXPENSE OF

PROVIDING A SUBSTITUTE PRODUCT OR SERVICE DURING PERIODS OF MALFUNCTION OR NON-USE.

Some states may not allow the exclusion of indirect, incidental or consequential damages, so the above exclusion may

not apply to you.

Smithco neither assumes, nor authorizes any person to assume for it, any other liability in connection with the

sale or use of this product.

Pagina se încarcă ...

Smithco SweepStar 48H and 60 Instrucțiuni de utilizare

Smithco SweepStar 48H and 60 Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente