Smithco Spray Star 1750 Instrucțiuni de utilizare

Marca: Smithco

Model: Spray Star 1750

Tip: Instrucțiuni de utilizare

Spray Star 1750

1752 Radion 8140

1754 TeeJet 744

1755 DynaJet/Aeros

1758 DynaJet/Radion 8140

SN 175G383

NOVEMBER 2020

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

Operator’s

CONTENTS

Introduction .................................................................. 1-8

Introduction ................................................................. 1

Symbols ...................................................................... 2

General Safe Practices ............................................ 3-6

Specications ............................................................. 7

Optional Spray Equipment .......................................... 7

Set Up ......................................................................... 8

Operation .................................................................... 9-14

Controls & Instruments ........................................... 9-10

Operating Instructions ...........................................11-12

Tank Agitation ........................................................... 13

Spray Cleaning .......................................................... 14

Diagrams ................................................................... 15-16

Wiring ........................................................................ 15

Hydraulic ................................................................... 16

Reference .................................................................. 17-20

Declaration of Conformity ..................................... 17-18

Quick Reference ....................................................... 19

TeeJet

App ............................................................... 20

Warranty ........................................................................

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

INTRODUCTION

Thank you for purchasing a Smithco product.

Read this manual and all other manuals pertaining to the Spray Star 1750 carefully as they have safety, op-

erating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment

damage. Use in conjunction with appropriate TeeJet Manuals.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides

are from the operator’s seat, facing forward.

All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. The serial number plate on the Spray Star 1750 is located on the left main frame, by front bumper. Re-

fer to engine manual for placement of engine serial number.

For product and accessory information, help nding a dealer, or to register your product please contact us at

www.smithco.com

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts





WARNING

Failure to follow cautious operating prac-

tices can result in serious injury to the

operator or other persons. The owner must

understand these instructions, and must

allow only trained persons who understand

these instructions to operate this vehicle.

WARNING:

Engine exhaust and some of its constituents are

known to the State of California to cause cancer,

birth defects, and other reproductive harm.

For more information visit

www.P65Warning.ca.gov

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

20° MAX

Read Operator’s

Manual

Engine Stop

Engine Start

Engine Run

Engine Oil

Water

Temperature

RPM

Gasoline

Diesel

Glow Plug

Hour Meter

Hand Throttle

Choke

Hydraulic

Oil Level

Ground Speed

Park Brake

Release

Lift Arm

Slow

Moving Parts

Pinch Point

Hydraulic Fluid

Penetration

Warning

Danger

Caution

Fast

Rollover

Danger

Hot Surface

Headlamp

Seat Belt

No Riders

Blower

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY

Read and understand this manual and all safety signs before operating and maintaining. Review the safety

instructions and precautions annually.

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL

YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF

OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

Safety Alert Symbol

This symbol with a warning statement means:

WARNING! BE ALERT!

YOUR SAFETY IS INVOLVED!

Carefully reard the message that follows

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The

appropriate signal word for each has been selected using the following guidelines:

DANGER: Red. Indicates an imminently hazardous situa-

tion that, if not avoided, will result in death or serious injury.

This signal word is to be limited to the most extreme situa-

tions typically for machine components which, for functional

purposes, cannot be guarded.

WARNING: Orange. Indicates a potentially hazardous

situation that, if not avoided, could result in death or serious

injury, and includes hazards that are exposed when guards

are removed. It may also be used to alert against unsafe

practices.

CAUTION: Yellow. Indicates a potentially hazardous situ-

ation that, if not avoided, may result in minor or moderate

injury. It may also be used to alert against unsafe practices.

IMPORTANT: Blue. Indicates procedures which should be

followed to avoid damage to the machine.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY DECAL LOCATION

If Safety Decals** have been damaged, removed, become illegible or parts

replaced without decals, new decals must be applied. New decals are avail-

able from your authorized distributor.

This is a list of decals located on the Spray Star 1750. Part number, description and location will help in reor-

dering decals.

A 15-902 Decal, Tank Volume

B 15-903 Decal, Rear Tank Volume

C** 15-463 Decal, Spray Pump

D 15-636 Decal, Spray Star 1750

E** 10-657 Decal, Control Panel

F** 51-184 Decal, Park Brake

G** 15-719 Decal, Speed Control

H** 25-298 Decal, Warning Hot

I** 25-307 Decal, Gas

J* 25-286 Decal, Pinch Point

K 25-356 Decal, Tire Pressure

L 25-373 Decal, Smithco

M 25-381 Decal, 96 dBA

N 27-077 Decal, Smithco

O** 27-093 Decal, Hydraulic Oil

P** 25-277 Decal, Battery

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine.

2. Never allow anyone to operate or service the machine or its optional equipment without proper training

and instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,

hands and feet. Operate the machine only in daylight or in good articial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can nd before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without

proper ventilation.

9. Fuel is highly ammable, handle with care. When lling tank stop 1 inch(2.54 cm) from top. Leave room

for expansion. DO NOT OVERFILL.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. Disengage all drives and set park brake before starting the engine.

12. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and

cause serious injury.

13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not stop or start suddenly on any slope.

C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.

D. Stay alert for holes in the terrain and other hidden hazards.

14. Before leaving operator’s position:

A. Disengage all drives.

B. Set park brake.

C. Shut engine o and remove the ignition key.

D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of

body away from moving parts.

15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

16. Keep the area of operation clear of all bystanders.

17. Never carry passengers.

18. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

19. Use parts and materials supplied by Smithco only. Do not modify any function or part.

20. Use caution when booms are down as they extend out beyond the center line of the machine.

21. The spray tank is a conned space, take precaution.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE SPRAYING PRACTICES

Persons engaged in the handling, preparation or application of chemicals must follow accepted practices to

insure the safety of themselves and others,

1. WEAR protective clothing including: gloves, hat, respirator, eye protection and skin covering suitable for

protection from chemicals being used.

2. BATHE thoroughly after any exposure to chemicals, giving particular attention to eyes, nose, ears and

mouth.

3. CLEAN equipment and materials in accordance with employer, municipal and state regulations. Use

only approved areas and drains.

4. DISPOSE of chemicals and rinse solutions by approved and legal means.

5. PROVIDE methods and materials for operators to wash eyes and hands immediately during the spray-

ing process.

6. PROVIDE methods and materials for control, safe dilution and neutralization of chemical spills during

preparation, spraying, transporting and cleanup.

7. Always check and follow the directions and safety warnings of the chemicals to be used.

8. Secure the discharge lines before starting the pump. An unsecured discharge line may whip.

9. Periodically inspect the pump and the system components.

10. Check hoses for weak or worn condition before each use. Make certain that all connections are tight

and secure.

11. Do not operate unit with leaks, frayed, kinked hoses or tubing. Repair or replace immediately.

12. Use only pipe, hose and ttings rated for maximum pressure or pressure at which pressure relief valve

is set at. When replacing pipe, hose or ttings, use new product.

13. Do not operate any fuel engines in an enclosed area. Be sure the area is well ventilated.

14. Do not use these pumps for pumping water or other liquids for human or animal consumption.

15. Do not pump ammable or explosive uids such as gasoline, fuel

oil, kerosene, etc. Do not use in explosive atmospheres. The pump

should be used only with liquids compatible with the pump compo-

nent materials.

16. Be sure all exposed moving parts are guarded and that all coupling devices are securely attached be-

fore applying power.

17. Before servicing, disconnect all power, make sure all pressure in the system is relieved, drain all liquids

from the system and ush.

18. Protect pump from freezing conditions by draining liquid and pumping rust inhibiting antifreeze solution

through the system, coating the pump interior.

19. TRANSPORT - Machine must be stopped to raise or lower booms. Because of cam system, if booms

are raised in transit they can fall forward or backward when coming to a stop or while traveling on un-

even terrain.

20. If using Simulated Speed with a Radion 8140, one needs to change back to

Ground Speed for proper rate control when spraying.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SPECIFICATIONS

WEIGHTS AND DIMENSIONS 1750 GAS

Length 120" (305 cm)

Width 65" (165 cm)

Width With Boom Open 240" (610 cm)

Height w/ ROPS 77" (195 cm)

Height w/ Booms Folded 110" (279 cm)

Wheel Base 68" (173 cm)

Weight Empty 1750 lbs (794 kg)

Weight Full 3500 lbs (1588 kg)

SOUND LEVEL (DB)

At ear level 96 dBA

At 3 ft (0.914 m) 98 dBA

At 30 ft (9.14 m) 88 dBA

ENGINE

Make Briggs & Stratton

Model# 613477

Type / Spec# 0271-J1

Horsepower 35 hp (26 kW)

Fuel Unleaded 87 Octane Gasoline Minimum

Cooling System Air Cooled

Lubrication System Full Pressure

Alternator 20 Amp

WHEELS & TIRE Front: Two 20 x 10.00 x 10 NHS Multi-Rib; 20 psi (1.4 bar)

Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 20 psi (1.4 bar)

SPEED

Innitely Variable 0-12 m.p.h. (0-20 kph)

BATTERY Automotive type 24F - 12 volt

BCI Group Size 24

Cold Cranking Amps 900 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 10.25" (26 cm)

Maximum Width 6.88" (17 cm)

Maximum Height 10" (25 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 10 gallon (37,9 liters)

Hydraulic Fluid 5 gallon (19 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

OPTIONAL EQUIPMENT

15-618 Water Meter Kit (Liters) 14-515 Water Meter Kit (Gallons)

15-619 Chemical Clean-load 17-506 Fresh Water Wash Tank

15-622 Canopy 15-835 Tank Rinsing System

15-965 Foam Marker 15-967 Hose Reel Mount Kit

17-580 20' HD Super Boom 17-585 18.5' HD Super Boom

15-968 26 Gal. Wash System with Electric Pump

16-129 Manual Rewind Hose Reel, 200-foot/61-meter capacity

16-906 Electric Rewind Hose Reel, 200-foot/61-meter capacity

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP

The Spray Star 1750 arrives from Smithco setup and ready for service. Depending on freight conditions the

battery may have to be installed.

The spray system is normally shipped attached to the 1750 Prime Mover. If a spray system is to be tted to a

Prime Mover by a dealer or factory, assemble and attach the components in accordance with the parts draw-

ings in the Spray Star 1750 Parts/Service Manual.

1. Check the tire pressure. The front and rear tires are 20 psi

(1.4 bar).

2. Battery is located under the seat. This is a negative

grounding system.

Connecting battery cables to the

wrong post could result in person-

al injury and/or damage to the elec-

trical system. Make sure battery

and cables do not interfere or rub

on any moving part. Connect red positive (+) cable (A) to

battery rst. When disconnecting remove black negative (-)

cable (B) rst.

3. Check hydraulic uid level in tank located under the seat. Remove cap and add SAE 10W-40 API Ser-

vice SJ or higher motor oil if necessary. Fluid level should be about 2-2

" (5-6.4 cm) from the top of the

tank when cold. DO NOT OVERFILL.

4. Fill fuel tank, located on the left side, with Unleaded 87 Octane gasoline (minimum). When lling the

fuel tank stop when the fuel reaches 1 inch (2.54cm) from the top. This space is necessary for fuel

expansion. DO NOT OVERFILL.

Fuel is ammable, caution must be used when storing or handling it. Do not

ll fuel tank while engine is running or an enclosed area, fumes are explosive

and dangerous to inhale. DO NOT SMOKE while lling the fuel tank. DO NOT

OVERFILL.

5. Machine should be greased before starting, refer to Spray Star 1750 Parts/Service Manual for location.

6. Attach the Spray Boom and any other Optional Equipment to the Prime Mover, in accordance with

instructions in the Spray Star 1750 Parts/Service Manual. The nozzles must be the correct distance

above the turf as described in Turf Spraying Guide. The spray boom must operate properly and the

outer sections must break away safely if an object is struck by them, they must then return to normal

operation position.

7. Be sure to double check boom heights, nozzle spacing and displacement before spraying.

8. Machine is shipped with windshield washer uid in Spray System to prevent freezing. Flush system

completely with clear water. Fill tank with water and re-tighten the four bolts used to hold the tank in

place.

Never allow pump to run dry! The valve on the suction side of the pump (be-

tween the pump and tank) must be fully open whenever the pump is operated.

9. Read operating instructions before starting.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

A. GPS Speedometer - The Speedometer indicates ground

speed of the vehicle in miles per hour.

B. Oil Light - The oil light should come on when the ignition is

on without the engine running and go out when the engine

is running. The oil light will light when the oil pressure is

low. If oil light should come on, shut engine o immediately

and nd the cause.

C. Ignition Switch - The ignition switch has three positions: O

- Run - Start.

D. Left Boom Switch - This rocker switch lifts and lowers the

left boom.

E. Right Boom Switch - This rocker switch lifts and lowers the

right boom.

F. Lights - This rocker switch turns lights on by pushing on the

top and o by pushing on the bottom.

G. Spray Pump - This rocker switch turns the spray pump on

by pushing on the top and o by pushing on the bottom.

Amber light indicates 'On'.

H. Ground Speed (Cruise) Control - This rocker switch initiates cruise control by pushing on the top and

turning it o by pushing on the bottom. Works with ground Speed Control foot switch(T). Green light

indicates 'On'.

I. Dual USB Charging Port - lets you charge your cell phone, tablet, or

other device.

J. Hand Throttle - The hand throttle is used to regulate engine speed.

K. Hour Meter - The hour meter indicates hours of machine operation. It

operates only when the ignition switch is on.

L. Buzzer - The buzzer sounds if the pump is running dry.

M. Choke - The choke is used in starting the engine. Pull choke out to

close choke plate when starting a cold engine. Push in when engine

starts. A warm engine may not require "choking" to start.

N. Spray Boss Control - Engages and disengages speed boss. Forward is

engage and all the way back is disengage. When the lever is engaged it

sets a stop for the accelerator. The accelerator pedal must be used to

maintain this speed. To adjust speed use the knob on the end of the

lever, counter clockwise increases speed and clockwise decreases speed. Disengage the lever and you

will have full accelerator pedal range.

SPEEDOMETER

This machine is equipped with a GPS Speedometer. Please note that if the speedometer has been powered

o longer than 4 hours, it could take up to 1 minute to acquire signal due to the satellites moving signicantly

from your location. This is normal. The current draw is extremely low and will have virtually zero impact on

a battery's charge. Hot start wire should be connected directly to battery +12volts and should remain pow-

ered 100% of the time. When GPS gauge rst receives power, the needle will sweep full counter clockwise

towards

0 mph. Pointer will stay at 0 mph and oscillate slightly at zero to indicate the GPS is acquiring satellites. GPS

is not yet functional to indicate speed. Once satellites are acquired (15-45 seconds), the pointer will swing

full scale and then back toward 0 mph to indicate it is now ready for operation.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

O. Park Brake - The park brake is only a parking brake. Pull back to release,

push forward to apply. Some adjustment can be made by turning the knob

clockwise to tighten and counter clockwise to loosen.

P. GNSS Antenna Switch - (Optional) Used to turn on/o GNSS Antenna,

used with spray systems.

Q. Accelerator Pedal - This pedal controls ground speed. Press pedal to

increase speed. Varying the amount of movement of the pedal will vary the

ground speed.

R. Reverse Pedal - This pedal controls ground speed in the reverse direction.

Press the pedal to reverse direction. Varying the amount of movement of

the pedal will vary the ground speed.

MASTER BOOM SWITCH (S)

The master boom switch (S), if required, is located on the left oorboard. It is used to override the master

switch on the computer console of the Radion Spray Systems. By pushing down it will turn on/o the booms.

For TeeJet Systems, the master switch on the computer must be on.

GROUND SPEED CONTROL (T)

The ground speed control (T) does not work the same as an automotive type cruise. The ground speed con-

trol is located on the center oorboard and is used to lock forward speed.

TO ENGAGE:

1. Flip rocker switch ‘On’ (L)(green light).

2. Obtain desired speed with foot pedal.

3. Step on foot switch(T) to lock speed.

4. Push foot switch again to disengage.

To avoid abrupt stop, place foot on traction pedal before disengaging speed

control.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

Before operating the Spray Star 1750, become familiar with all controls and functions. Also complete all maintenance re-

quirements and read all safety warnings. Knowing the Spray Star 1750 thoroughly, how it operates, and by doing the pre-

scribed maintenance steps, you can expect trouble free operation for years to come.

SAFETY

Safety needs to always be the concern of an operator of a moving vehicle or any machine with moving parts.

1. Keep all shields and guards in place.

2. Keep the parking brake engaged any time the operator is away from the vehicle or whenever service is performed.

3. Always wear the necessary protective clothing and equipment.

4. Turn engine o when refueling or performing maintenance not specically requiring engine power.

DAILY CHECKLIST

1. Check the engine oil level. Add as needed. DO NOT OVERFILL. Refer to engine owner's manual for oil grade and

procedure.

2. Tire pressure should be 20 psi (1.4 bar) maximum.

3. Inspect the electrical system and battery cables for loose connections or frayed wiring. Replace any faulty equip-

ment or tighten if loose.

4. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.

5. Inspect hydraulic lines for damage or leaks. Never use hands to inspect for leaks.

6. Check the hydraulic uid level. The hydraulic uid tank is located on the left side of the machine. The uid level

should be 2"-2½" (5 - 6.4 cm) from the top of the tank when cold. Use only SAE 10W-40 API Service SJ or higher

Motor Oil.

7. Inspect the steering, throttle and shift linkages for good hookups and clear travel.

8. Check controls for smooth, proper working operation. Lubricate as needed.

9. Check park brake adjustments. Adjust as required.

10. Check anti-vibration mounts on engine frame.

STARTING THE ENGINE

1. Make sure the fuel ow valve is ‘On’. It is located on the fuel tank.

2. The ignition switch is located on the dashboard. Insert the key (A) and turn

clockwise until the engine starts (C). Release the key and it will return to the

run position (B). Use the choke and hand throttle as necessary.

3. Diesel - Insert the key (A) and turn clockwise to (B). When glow plug light

goes o Turn key to (C) until the engine starts. Release the key and it will

return to the run position (B).

4. Allow engine to idle and warm up before selecting direction of travel.

STOPPING THE ENGINE

If the engine has been running under high power,

let it run at slow idle speed a few minutes to cool

the engine down, before turning the ignition switch to the OFF position.

1. Disengage spray pump.

2. Move the throttle lever to “slow” and turn ignition key to the “o” position.

3. Remove the ignition key and engage the park brake.

Never leave the vehicle unattended with the engine running. Always bring the vehicle to

a complete stop, engage park brake, turn key o and remove key.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

Before using the Spray Star 1750, the operator and spray technician must familiarize themselves with all of the informa-

tion on chemical spraying contained in the Turf Spray Guide.

All testing and calibrating of sprayers is to be done with water, not chemicals. This

insures the safety to all involved in performing the calibration operation. Only after all

calibration procedures are completed should chemical be added to the sprayer.

TOWING UNIT

When it is necessary to move the Spray Star 1750 without the engine running, the bypass valve built into hydrostatic

pump must be "open" by turning it

turn to open. The valve is located on the back side of the pump. An "open" valve al-

lows uid to pass through the wheels freely. When normal driven operation is desired, valve should be "closed" by turning

it clockwise. Failure to "close" the valve with engine running means no power to wheels.

HILLSIDE OPERATION

Do NOT stop or start suddenly on any slope. Be especially cautious when changing direction. Do NOT operate on slopes

greater than 10°.

BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or any ignited

object to come near the battery. When charging or working near battery, always shield your eyes and always provide

proper ventilation.

Battery cable should be disconnected before using “Fast Charge”.

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging rate. If

electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp rst and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte

is splashed on any part of your body, ush all contact areas immediately with liberal

amounts of water. Get medical attention immediately.

JUMP STARTING

Use of booster battery and jumper cables. Particular care should be used when con-

necting a booster battery. Use proper polarity in order to prevent sparks.

To jump start (negative grounded battery):

1. Shield eyes.

2. Connect ends of one cable to positive (+) terminals of each

battery, rst (A) then (B).

3. Connect one end of other cable to negative (-) terminal of

"good" battery (C).

4. Connect other end of cable (D) to engine block on unit being

started (NOT to negative (-) terminal of battery)

To prevent damage to other electrical components on unit being

started, make certain that engine is at idle speed before disconnect-

ing jumper cables.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

TANK AGITATION

SPRAYER VALVE SETTINGS AND SPRAY TANK AGITATION

The ball valve on the suction side of the pump, between the tank and the pump must be open before pump is

engaged. Close this valve only when necessary to clean the lter with spray material in the spray tank.

There is one manual ow control valve on the discharge side of the spray system. This valve controls the

agitator. This valve may be opened as much as necessary to provide hydraulic agitation through the quadra-

jet agitator in the tank bottom. This valve may be partially closed to prevent or reduce foam buildup from the

spray materials inside the tank. When the liquid level in the spray tank reaches a certain level (usually 1-25

gallons (3.8-95 Liters) depending on terrain and other conditions) it may be necessary to close the valve in

the agitator line in order to prevent loss of suction prime.

If your Spray Star is tted with a hose reel, there is a second ball valve on the discharge system to supply ma-

terial to the hose reel.

The Quadrajet agitation system operates with four venturi jets in the tank bottom. These jets have replaceable

orice discs which discharge the following amounts of spay material.

Input to Input to Agitator Agitator Agitator Agitator

Nozzle Agitator Agitator Pressure Pressure Output Output

Diameter in gpm in L/min in psi in bar in gpm in L/min

" 1.9 7.2 25 1.7 6.3 23.8

" 2.7 10.2 50 3.4 10.0 37.9

" 3.8 14.4 100 6.9 15.0 56.8

" 2.8 10.6 25 1.7 7.6 28.8

" 4.2 15.9 50 3.4 12.2 46.2

" 5.5 20.8 100 6.9 17.5 66.2

" 3.6 13.6 25 1.7 9.1 34.4

" 5.6 21.2 50 33.4 14.3 54.1

" 7.9 29.9 100 6.9 18.7 70.8

You can change orice disc sizes to enhance spray system performance. Small-

er discs reduce amount of agitation (desirable in some foaming materials) and

make more dis-chargeable liquid available for nozzles. Larger (or none) discs

increase amount of agitation and make less dis chargeable liquid available for

nozzles.

AGITATION LINE STRAINER CLEANING

Agitation line strainer is located below the sprayer lter. This strainer catches

impurities that go to the turbo-jet agitation system in the spray tank. It has a

quick disconnect pin on it to remove the bowl. After EVERY use, remove bowl

and clean screen. Replace screen as needed. We recommend a 50 Mesh

screen.

DYNAJET

NOZZLE CLEANING

The Nozzle Coil Assembly will need to be taken

apart and cleaned on a regular basis. To take apart

and clean you will need to use two wrenches pro-

vided with the DynaJet

System. Loosen the Nozzle

assembly by placing a wrench on the tube assembly

and one on the stainless cap. Hold one in place and

turn the other wrench to loosen assembly. Once

apart, clean with water and check for deteriorating

parts. Replace parts as needed by ordering the

Spare Parts Kit 20-673-01P.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SPRAYER CLEANING

One of the most common causes for faulty-pump performance is corrosion inside the pump. Flush the pump and

entire system with a solution that will chemically neutralize the liquid pumped. Mix according to manufacturer’s

directions. This will dissolve most residue remaining in the pump, leaving the inside of the pump clean for the next

use.

TO PREVENT CORROSION

After cleaning the pump as directed, ush it with a permanent type automobile antifreeze (Prestone, Zerex, etc.)

containing a rust inhibitor. Use a 50% solution that is, half antifreeze and half water. Then coat the interior of the

pump with a substance which will prevent corrosion such as Fluid Film or WD40. If unit will not be used for an ex-

tended period of time, disconnect hoses into and out of the pump, seal openings to the pump with caps or tape.

Dispose of uids according to all federal, state and local regulations.

All chemicals and chemical residue must be removed after each use. Dispose of

uids and residue according to all federal, state and local regulations.

SPRAYER CLEANING

Empty tank and clean unit thoroughly after each use following these instructions:

1. Turn o 3-way valve and rinse inside of tank thoroughly with clean water, remove cap from valve to drain.

2. Fill tank ten percent full with clean water, Turn 3-way valve on and start pump and discharge water through

spray hose or spray boom (with nozzles removed), until empty.

3. Turn o 3-way valve again and rinse tank interior thoroughly. Remove cap from 3-way valve to drain.

4. Rinse exterior of sprayer thoroughly with clean water.

5. This sprayer is equipped with a self cleaning strainer. The strainer uses the excess pump ow to bypass clog-

ging particles back to the spray tank. There is a gap between the tapered inner cylinder and the screen face

that causes the inlet uid to ow at a high velocity past the screen face providing a continuous wash down of

particles. For this wash down to occur a minimum of +GPM/23 l/min is required through the bypass line.

AGITATION LINE STRAINER CLEANING

Agitation line strainer is located below the sprayer lter. This strainer catches

impurities that go to the turbo-jet agitation system in the spray tank. It has a

quick disconnect pin on it to remove the bowl. After EVERY use, remove bowl

and clean screen. Replace screen as needed. We recommend a 50 Mesh

screen.

MANUAL HOSE REEL

Located at the back of the Spray Star on top of the tank. Open the ball valve

located near the manifold valve to allow uid to ow into the hose reel. Place

the lockout pin in the unlocked position by pulling and turning it half a turn, this

will allow you to pull out additional hose or to use the handle and wind up the

hose. To prevent movement during transport or storage place the lockout pin in

the locked position.

ELECTRIC HOSE REEL

Located at the back of the Spray Star on top of the tank. Open the ball valve

located near the manifold valve to allow uid to ow into the hose reel. To un-

wind hose just pull on the hose to get the desired amount. To wind up the hose

make sure the toggle switch is in the ON position, push the momentary push

button switch until you have reeled in the amount of hose desire. Turn o the safety switch when not in use.

FOAM MARKER

Located to the right of the control panel. Use lever on compressor to designate which boom is to be used to dis-

pense foam. Use dial located on the foamer to adjust pressure for the amount of foam that will be dispensed.

Switch on compressor also turns foamer on or o.

Diagrams

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

WIRING DIAGRAM

Diagrams

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

HYDRAULIC DIAGRAM

Business name and full address of the manufacturer ▪ Търговско име и пълен адрес на производителя ▪ Obchodní jméno a plná adresa

výrobce ▪ Producentens firmanavn og fulde adresse ▪ Bedrijfsnaam en volledig adres van de fabrikant ▪ Tootja ärinimi ja täielik aadress ▪

Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des

Herstellers ▪ Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo

completo del fabbricante ▪ Uzņēmuma nosaukums un pilna ražotāja adrese ▪ Verslo pavadinimas ir pilnas gamintojo adresas ▪ Isem

kummerċjali u indirizz sħiħ tal-fabbrikant ▪ Nazwa firmy i pełny adres producenta ▪ Nome da empresa e endereço completo do fabricante ▪

Denumirea comercială şi adresa completă a producătorului ▪ Obchodný názov a úplná adresa výrobcu ▪ Naziv podjetja in polni naslov

proizvajalca ▪ Nombre de la empresa y dirección completa del fabricante ▪ Tillverkarens företagsnamn och kompletta adress

Smithco Inc.

34 West Avenue

Wayne, PA USA

19087-3311

Product Code ▪ Код на продукта ▪ Kód výrobku ▪ Produktkode ▪ Productcode ▪ Toote kood ▪ Tuotekoodi ▪ Code produit ▪ Produktcode ▪

Κωδικός προϊόντος ▪ Termékkód ▪ Codice prodotto ▪ Produkta kods ▪ Produkto kodas ▪ Kodiċi tal-Prodott ▪ Kod produktu ▪ Código do Produto

▪ Cod produs ▪ Kód výrobku ▪ Oznaka proizvoda ▪ Código de producto ▪ Produktkod

15-600

Machine Name ▪ Наименование на машината ▪ Název stroje ▪ Maskinnavn ▪ Machinenaam ▪ Masina nimi ▪ Laitteen nimi ▪ Nom de la

machine ▪ Maschinenbezeichnung ▪ Ονομασία μηχανήματος ▪ Gépnév ▪ Denominazione della macchina ▪ Iekārtas nosaukums ▪ Mašinos

pavadinimas ▪ Isem tal-Magna ▪ Nazwa urządzenia ▪ Nome da Máquina ▪ Numele echipamentului ▪ Názov stroja ▪ Naziv stroja ▪ Nombre de

la máquina ▪ Maskinens namn

Spray Star 1750

Designation ▪ Предназначение ▪ Označení ▪ Betegnelse ▪ Benaming ▪ Nimetus ▪ Tyyppimerkintä ▪ Pažymėjimas ▪ Bezeichnung ▪

Χαρακτηρισμός ▪ Megnevezés ▪ Funzione ▪ Apzīmējums ▪ Lithuanian ▪ Denominazzjoni ▪ Oznaczenie ▪ Designação ▪ Specificaţie ▪ Označenie

▪ Namen stroja ▪ Descripción ▪ Beteckning

Turf Sprayer

Serial Number ▪ Сериен номер ▪ Sériové číslo ▪ Serienummer ▪ Serienummer ▪ Seerianumber ▪ Valmistusnumero ▪ Numéro de série ▪

Seriennummer ▪ Σειριακός αριθμός ▪ Sorozatszám ▪ Numero di serie ▪ Sērijas numurs ▪ Serijos numeris ▪ Numru Serjali ▪ Numer seryjny ▪

Número de Série ▪ Număr de serie ▪ Sériové číslo ▪ Serijska številka ▪ Número de serie ▪ Serienummer

175G353 - 175G700

Engine ▪ Двигател ▪ Motor ▪ Motor ▪ Motor ▪ Mootor ▪ Moottori ▪ Moteur ▪ Motor ▪ Μηχανή ▪ Modulnév ▪ Motore ▪ Dzinējs ▪ Variklis ▪ Saħħa

Netta Installata ▪ Silnik ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor

Briggs & Stratton 613477

Net Installed Power ▪ Нетна инсталирана мощност ▪ Čistý instalovaný výkon ▪ Installeret nettoeffekt ▪ Netto geïnstalleerd vermogen ▪

Installeeritud netovõimsus ▪ Asennettu nettoteho ▪ Puissance nominale nette ▪ Installierte Nettoleistung ▪ Καθαρή εγκατεστημένη ισχύς ▪

Nettó beépített teljesítmény ▪ Potenza netta installata ▪ Paredzētā tīkla jauda ▪ Grynoji galia ▪ Wisa’ tal-Qtugħ ▪ Moc zainstalowana netto ▪

Potência instalada ▪ Puterea instalată netă ▪ Čistý inštalovaný výkon ▪ Neto vgrajena moč ▪ Potencia instalada neta ▪ Nettoeffekt

26 kW

Conforms to Directives ▪ В съответствие с директивите ▪ Splňuje podmínky směrnic ▪ Er i overensstemmelse med direktiver ▪ Voldoet aan

de richtlijnen ▪ Vastab direktiividele ▪ Direktiivien mukainen ▪ Conforme aux directives ▪ Entspricht Richtlinien ▪ Ακολουθήστε πιστά τις

Οδηγίες ▪ Megfelel az irányelveknek ▪ Conforme alle Direttive ▪ Atbilst direktīvām ▪ Atitinka direktyvų reikalavimus ▪ Valutazzjoni tal-

Konformità ▪ Dyrektywy związane ▪ Cumpre as Directivas ▪ Respectă Directivele ▪ Je v súlade so smernicami ▪ Skladnost z direktivami ▪

Cumple con las Directivas ▪ Uppfyller direktiv

2006/42/EC;

2000/14/EC Annex VI . Part 1

Conformity Assessment ▪ Оценка за съответствие ▪ Hodnocení plnění podmínek ▪ Overensstemmelsesvurdering ▪

Conformiteitsbeoordeling ▪ Vastavushindamine ▪ Vaatimustenmukaisuuden arviointi ▪ Evaluation de conformité ▪ Konformitätsbeurteilung ▪

Διαπίστωση Συμμόρφωσης ▪ Megfelelőség-értékelés ▪ Valutazione della conformità ▪ Atbilstības novērtējums ▪ Atitikties įvertinimas ▪ Livell

tal-Qawwa tal-Ħoss Imkejjel ▪ Ocena zgodności ▪ Avaliação de Conformidade ▪ Evaluarea conformităţii ▪ Vyhodnotenie zhodnosti ▪ Ocena

skladnosti ▪ Evaluación de conformidad ▪ Bedömning av överensstämmelse

2006/42/EC Annex VIII

Measured Sound Power Level ▪ Измерено ниво на звукова мощност ▪ Naměřený akustický výkon ▪ Målte lydstyrkeniveau ▪ Gemeten

geluidsniveau ▪ Mõõdetud helivõimsuse tase ▪ Mitattu äänitehotaso ▪ Niveau de puissance sonore mesuré ▪ Gemessener Schalldruckpegel ▪

Σταθμισμένο επίπεδο ηχητικής ισχύος ▪ Mért hangteljesítményszint ▪ Livello di potenza sonora misurato ▪ Izmērītais skaņas jaudas līmenis ▪

Išmatuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna mierzona ▪ Nível sonoro medido ▪ Nivelul măsurat al

puterii acustice ▪ Nameraná hladina akustického výkonu ▪ Izmerjena raven zvočne moči ▪ Nivel de potencia sonora medido ▪ Uppmätt

ljudeffektsnivå

96dB(A)Lwa

Guaranteed Sound Power Level ▪ Гарантирано ниво на звукова мощност ▪ Garantovaný akustický výkon ▪ Garanteret lydstyrkeniveau ▪

Gegarandeerd geluidsniveau ▪ Garanteeritud helivõimsuse tase ▪ Taattu äänitehotaso ▪ Niveau de puissance sonore garanti ▪ Garantierter

Schalldruckpegel ▪ Εγγυημένο επίπεδο ηχητικής ισχύος ▪ Szavatolt hangteljesítményszint ▪ Livello di potenza sonora garantito ▪ Garantētais

skaņas jaudas līmenis ▪ Garantuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna gwarantowana ▪ Nível

sonoro farantido ▪ Nivelul garantat al puterii acustice ▪ Garantovaná hladina akustického výkonu ▪ Zajamčena raven zvočne moči ▪ Nivel de

potencia sonora garantizado ▪ Garanterad ljudeffektsnivå

98 dB(A)Lwa

Conformity Assessment Procedure (Noise) ▪ Оценка за съответствие на процедурата (Шум) ▪ Postup hodnocení plnění podmínek (hluk) ▪

Procedure for overensstemmelsesvurdering (Støj) ▪ Procedure van de conformiteitsbeoordeling (geluid) ▪ Vastavushindamismenetlus (müra)

▪ Vaatimustenmukaisuuden arviointimenettely (Melu) ▪ Procédure d’évaluation de conformité (bruit) ▪ Konformitätsbeurteilungsverfahren

(Geräusch) ▪ Διαδικασία Αξιολόγησης Συμμόρφωσης (Θόρυβος) ▪ Megfelelőség-értékelési eljárás (Zaj) ▪ Procedura di valutazione della

conformità (rumore) ▪ Atbilstības novērtējuma procedūra (troksnis) ▪ Atitikties įvertinimo procedūra (garsas) ▪ Proċedura tal-Valutazzjoni tal-

Konformità (Ħoss) ▪ Procedura oceny zgodności (poziom hałasu) ▪ Processo de avaliação de conformidade (nível sonoro) Procedura de

evaluare a conformităţii (zgomot) ▪ Postup vyhodnocovania zhodnosti (hluk) ▪ Postopek za ugotavljanje skladnosti (hrup) ▪ Procedimiento de

evaluación de conformidad (ruido) ▪ Procedur för bedömning av överensstämmelse (buller)

2000/14/EC Annex VI Part 1

UK Notified Body for 2000/14/EC ▪ Нотифициран орган в Обединеното кралство за 2000/14/ЕО ▪ Úřad certifikovaný podle směrnice č.

2000/14/EC ▪ Det britiske bemyndigede organ for 2001/14/EF ▪ Engels adviesorgaan voor 2000/14/EG ▪ Ühendkuningriigi teavitatud asutus

direktiivi 2000/14/EÜ mõistes ▪ Direktiivin 2000/14/EY mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ▪ Organisme notifié concernant

la directive 2000/14/CE ▪ Britische benannte Stelle für 2000/14/EG ▪ Κοινοποιημένος Οργανισμός Ηνωμένου Βασιλείου για 2000/14/ΕΚ ▪

2000/14/EK – egyesült királyságbeli bejelentett szervezet ▪ Organismo Notificato in GB per 2000/14/CE ▪ 2000/14/EK AK reģistrētā

organizācija ▪ JK notifikuotosios įstaigos 2000/14/EC ▪ Korp Notifikat tar-Renju Unit għal 2000/14/KE ▪ Dopuszczona jednostka badawcza w

Wielkiej Brytanii wg 2000/14/WE ▪ Entidade notificada no Reino Unido para 2000/14/CE ▪ Organism notificat în Marea Britanie pentru

2000/14/CE ▪ Notifikovaný orgán Spojeného kráľovstva pre smernicu 2000/14/ES ▪ Britanski priglašeni organ za 2000/14/ES ▪ Cuerpo

notificado en el Reino Unido para 2000/14/CE ▪ Anmält organ för 2000/14/EG i Storbritannien

Smithco West Inc.

200 West Poplar Avene

Cameron, WI 54822 USA

Operator Ear Noise Level ▪ Оператор на нивото на доловим от ухото шум ▪ Hladina hluku v oblasti uší operátora ▪ Støjniveau i førers

ørehøjde ▪ Geluidsniveau oor bestuurder ▪ Müratase operaatori kõrvas ▪ Melutaso käyttäjän korvan kohdalla ▪ Niveau de bruit à hauteur des

oreilles de l’opérateur ▪ Schallpegel am Bedienerohr ▪ Επίπεδο θορύβου σε λειτουργία ▪ A kezelő fülénél mért zajszint ▪ Livello di potenza

sonora all’orecchio dell’operatore ▪ Trokšņa līmenis pie operatora auss ▪ Dirbančiojo su mašina patiriamo triukšmo lygis ▪ Livell tal-Ħoss fil-

Widna tal-Operatur ▪ Dopuszczalny poziom hałasu dla operatora ▪ Nível sonoro nos ouvidos do operador ▪ Nivelul zgomotului la urechea

operatorului ▪ Hladina hluku pôsobiaca na sluch operátora ▪ Raven hrupa pri ušesu upravljavca ▪ Nivel sonoro en el oído del operador ▪

Ljudnivå vid förarens öra

96 dB(A)Lwa (2006/42/EC)

DECLARATION OF CONFORMITY ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ PROHLÁŠENÍ O SHODĚ ▪ OVERENSSTEMMELSESERKLÆRING ▪

CONFORMITEITSVERKLARING ▪ VASTAVUSDEKLARATSIOON ▪ VAATIMUSTENMUKAISUUSVAKUUTUS ▪ DECLARATION DE

CONFORMITE ▪ KONFORMITÄTSERKLÄRUNG ▪ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ▪ MEGFELELŐSÉGI NYILATKOZAT ▪ DICHIARAZIONE DI

CONFORMITÀ ▪ ATBILSTĪBAS DEKLARĀCIJA ▪ ATITIKTIES DEKLARACIJA ▪ DIKJARAZZJONI TAL-KONFORMITÀ ▪ DEKLARACJA

ZGODNOŚCI ▪ DECLARAÇÃO DE CONFORMIDADE ▪ DECLARAŢIE DE CONFORMITATE ▪ VYHLÁSENIE O ZHODE ▪ IZJAVA O SKLADNOSTI

▪ DECLARACIÓN DE CONFORMIDAD ▪ DEKLARATION OM ÖVERENSSTÄMMELSE

Reference