Ransomes 62834, 62835, 62836, 62849 Accessories Manual

Marca: Ransomes

Model: 62834, 62835, 62836, 62849

Tip: Accessories Manual

Instruction

Sheet

When Performance Matters.

™

WARNING

If incorrectly used, this machine can cause severe injury. Those who use

and maintain this machine should be trained in its proper use, warned of its

dangers and should read the entire manual before attempting to set up,

operate, adjust, or service the machine.

1 - INCLUDES ITEMS 3 - 16

GP400 TrueSet

™

Reels

62834 – 22 in. 7 Blade TrueSet

™

Reel

62835 – 22 in. 9 Blade TrueSet

™

Reel

62836 – 22 in. 11 Blade TrueSet

™

Reel

62849 – 22 in. 15 Blade TrueSet

™

Reel

4258371-P2

This manual contains adjustment, maintenance,

troubleshooting instructions, and parts list for your new

Jacobsen reel. This manual should be stored with the

mower for reference during operation.

Before you operate your mower, you and each operator

you employ should read the manual carefully in its

entirety. By following the safety, operating, and

maintenance instructions, you will prolong the life of your

mower and maintain its maximum efficiency.

If additional information is needed, contact your

Jacobsen Dealer.

The serial plate is attached to the reel frame. Jacobsen

recommends you record these numbers below for easy

reference.

CHARLOTTE, NC PRODUCT OF U.S.A.

A Textron Company

Proposition 65 Warning

This product contains or emits

chemicals known to the State of

California to cause cancer and birth

defects or other reproductive harm.

FOREWORD

Suggested Stocking Guide

To keep your mower fully operational and productive, Jacobsen suggests you maintain a stock of the more commonly

used maintenance items. We have included part numbers for additional support materials and training aids.

To order any of the following material:

1. Write your full name and complete address on your

order form.

2. Explain where and how to make shipment:

❑ UPS ❑ Regular Mail

❑ Overnight ❑ 2nd Day

3. Order by the quantity desired, the part number, and

the description of the part.

4. Send or bring the order to your authorized Jacobsen

Dealer.

Service Parts

Service Support Material

Qty. Part No. Description Qty. Part No. Description

4252470 Bedknife Screw (100 Pack)

460008 Cotter Pin, 5/64 x 3/4”

Qty. Part No. Description

4269792 5 in. Reel Technical Repair Manual

Litho in U.S.A. 8-2012

or portions thereof in any form.”

These are the original instructions verified by

Jacobsen, A Textron Company.

Table of Contents

1Safety

1.1 Operating Safety............................................... 4

1.2 Important Safety Notes ..................................... 5

2 Specifications

2.1 Product Identification ........................................ 6

2.2 Cutting Units ..................................................... 6

2.3 Accessories & Support Literature ..................... 6

2.4 Declaration of Incorporation ............................. 7

3Setup

3.1 Front Roller and Accessories ........................... 9

3.2 Mounting the Cutting units ................................ 9

4 Adjustments

4.1 General........................................................... 10

4.2 Bedknife-To-Reel ............................................ 10

4.3 Bedknife Adjustment ....................................... 11

4.4 Cutting Height ................................................. 11

4.5 Reel Bearing ................................................... 12

4.6 Bedknife Adjuster Spring ................................ 12

4.7 Bedknife Adjuster Tension .............................. 12

4.8 Grinding Bedknife ........................................... 12

4.9 Torque Specification ....................................... 13

1 SAFETY

1.1 OPERATING SAFETY ______________________________________________________

1. Safety is dependent upon the awareness, concern

and prudence of those who operate or service the

equipment. Never allow minors to operate any

equipment.

2. It is your responsibility to read this manual and all

publications associated with this equipment (Safety &

Operation Manual, Engine Manual, and attachments/

accessories instruction sheets). If the operator

cannot read English it is the owner’s responsibility to

explain the material contained in this manual to them.

3. Learn the proper use of the machine, the location

and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar

equipment can lead to accidents.

4. Never allow anyone to operate or service the

machine or its attachments without proper training

and instructions; or while under the influence of

alcohol or drugs.

5. Wear all the necessary protective clothing and

personal safety devices to protect your head, eyes,

ears, hands, and feet. Operate the machine only in

daylight or in good artificial light.

6. Evaluate the terrain to determine what accessories

and attachments are needed to properly and safely

perform the job. Only use accessories and

attachments approved by Jacobsen.

7. Stay alert for holes in the terrain and other hidden

hazards.

8. Inspect the area where the equipment will be used.

Pick up all the debris you can find before operating.

Beware of overhead obstructions (low tree limbs,

electrical wires, etc.) and also underground obstacles

(sprinklers, pipes, tree roots, etc.). Enter a new area

cautiously. Stay alert for hidden hazards.

9. Never direct discharge of material toward bystanders,

nor allow anyone near the machine while in

operation. The owner/operator can prevent and is

responsible for injuries inflicted to themselves, to

bystanders, and damage to property.

10. Do not carry passengers. Keep bystanders and pets

a safe distance away.

11. Never operate equipment that is not in perfect

working order or is without decals, guards, shields,

discharge deflectors, or other protective devices

securely fastened in place.

12. Never disconnect or bypass any switch.

13. Do not change the engine governor setting or

overspeed the engine.

14. Carbon monoxide in the exhaust fumes can be fatal

when inhaled. Never operate the engine without

proper ventilation or in an enclosed area.

15. Fuel is highly flammable; handle with care.

16. Keep the engine clean. Allow the engine to cool

before storing and always remove the ignition key.

17. Disengage all drives and engage parking brake

before starting the engine (motor). Start the engine

only when sitting in operator’s seat, never while

standing beside the unit.

18. Equipment must comply with the latest federal, state,

and local requirements when driven or transported

on public roads. Watch out for traffic when crossing

or operating on or near roads.

19. Local regulations may restrict the age of the operator.

20. Never use your hands to search for oil leaks.

Hydraulic fluid under pressure can penetrate the skin

and cause serious injury.

21. Operate the machine up and down the face of slopes

(vertically), not across the face (horizontally).

22. To prevent tipping or loss of control, do not start or

stop suddenly on slopes. Reduce speed when

making sharp turns. Use caution when changing

directions.

23. Always use the seat belt when operating mowers

equipped with a Roll Over Protective Structure

(ROPS).

Never use a seat belt when operating mowers

without a ROPS.

24. Always disconnect battery cables from battery before

performing any welding operation on the mower.

This machine is to be operated and maintained as specified in this manual and is intended for the professional

maintenance of specialized turf grasses. It is not intended for use on rough terrain or long grasses.

WARNING

EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS.

Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive

instruction from someone familiar with the equipment before being allowed to operate the machine.

SAFETY 1

1.2 IMPORTANT SAFETY NOTES ________________________________________________

This safety alert symbol is used to alert you to potential hazards.

DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious

injury.

CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury

and property damage. It may also be used to alert against unsafe practices.

NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may

also be used to alert against unsafe practices.

For pictorial clarity, some illustrations in this manual may show shields, guards or plates open, or removed. Under no

circumstances should this equipment be operated without these devices securely fastened in place.

By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum

efficiency. Adjustments and maintenance should always be performed by a qualified technician.

If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the

latest methods to service this equipment and can provide prompt and efficient service.

WARNING

The Interlock System on this mower prevents the mower from starting unless

the parking brake is engaged, reel levers are off, and traction lever is in

Neutral. The system will stop the engine if the operator leaves the seat

without engaging the parking brake, setting the reel levers to off, and placing

traction lever in Neutral.

NEVER operate mower unless the Interlock System is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction lever to Neutral.

b. Disengage all drives.

c. Lower all implements to the ground.

d. Engage parking brake.

e. Stop engine and remove the ignition key.

2. Keep hands, feet, and clothing away from moving parts. Wait for all

movement to stop before you clean, adjust, or service the machine.

3. Keep the area of operation clear of all bystanders and pets.

4. Never carry passengers.

2 SPECIFICATIONS

2.1 PRODUCT IDENTIFICATION_________________________________________________

62834.............................. GP400 22 in. (559 mm), 7 Blade

Reel, without front roller or motor

adapter.

62835.............................. GP400 22 in. (559 mm), 9 Blade

Reel, without front roller or motor

adapter.

62836.............................. GP400 22 in. (559 mm), 11 Blade

Reel, without front roller or motor

adapter.

62849.............................. GP400 22 in. (559 mm), 15 Blade

Reel, without front roller or motor

adapter.

Serial Number ............... An identification plate, like the one

shown, listing the serial number, is

attached to the frame of the reel.

Always provide the serial number of the unit when ordering

replacement parts or requesting service information.

2.2 CUTTING UNITS___________________________________________________________

Reel Diameter................. 5 in. (127 mm)

22 in. Blade Options ....... 7, 9, 11, or 15 blades

Height of Cut Range ....... 1/16 to 7/16 in. (1.6 to 11.1 mm)

Cutting Frequency:

7 Blade ..................... 0.079 in./mph (1.247 mm/kph)

9 Blade ..................... 0.061 in./mph (0.963 mm/kph)

11 Blade ................... 0.050 in./mph (0.789 mm/kph)

15 Blade ................... 0.037 in./mph (0.584 mm/kph)

2.3 ACCESSORIES & SUPPORT LITERATURE ____________________________________

Contact your area Jacobsen Dealer for a complete listing of accessories and attachments.

Accessories

Orange Touch-up Paint (12 oz. spray) .......................554598

Rear Roller Cleaner .....................................................62820

Turf Groomer 1/4” Spacing...........................................67912

Turf Groomer 1/2” Spacing...........................................67914

High Cut Roller Kit .......................................................68634

Motor Adapter Kit.......................................................894991

Magknife Kit

22 in. Medium Section Magknife Kit.........................4266571

22 in. Tournament Magknife Kit ...............................4266551

22 in. Super Tournament Magknife Kit.....................4266570

Solid Rollers

22 in. with Scraper (Light)............................................ 68530

22 in. with Scraper....................................................... 68641

22 in. Solid Tube Rear Roller................................... 1004990

Grooved Rollers

22 in. Assembled Disc ................................................. 68527

22 in. Machined Aluminum ..........................................68614

22 in. Machined Steel.................................................. 68613

22 in. Segmented Roller.............................................. 68673

Support Literature

Technical Repair Manual ......................................... 4269792

CHARLOTTE, NC PRODUCT OF U.S.A.

A Textron Company

62834001651

CAUTION

Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the

equipment.

SPECIFICATIONS 2

2.4 DECLARATION OF INCORPORATION _________________________________________

DECLARATION OF INCORPORATION ▪ ДЕКЛАРАЦИЯ ЗА ОБЕДИНЕНИЕ ▪ PROHLÁŠENÍ O ZALOŽENÍ SPOLEČNOSTI ▪ INKORPORERINGSERKLÆRING ▪

INCORPORATIEVERKLARING ▪ KINNITUS ÜHENDAMISE KOHTA ▪ ASENNUSTODISTUS ▪ DECLARATION D’INCORPORATION ▪ EINBAUBESCHEINIGUNG ▪ ΔΗΛΩΣΗ ΜΗ

ΣΥΜΜΟΡΦΩΣΗΣ ▪ BEÉPÍTÉSI NYILATKOZAT ▪ DICHIARAZIONE DI INCORPORAZIONE ▪ NOFORMĒŠANAS DEKLARĀCIJA ▪ PRIJUNGIMO DEKLARACIJA ▪

DIKJARAZZJONI

TA’ INKORPORAZZJONI ▪ DEKLARACJA ZGODNOŚCI DLA PODZESPOŁU ▪ DECLARAÇÃO DE INCORPORAÇÃO ▪ DECLARAŢIE DE ÎNCORPORARE ▪ VYHLÁSENIE O

ZABUDOVANÍ SÚČASTI ▪ IZJAVA ZA VGRADNJO ▪ DECLARACIÓN DE INCORPORACIÓN ▪ INBYGGNADSDEKLARATION

Business name and full address of the manufacturer ▪ Търговско име и пълен адрес на производителя ▪ Obchodní jméno a plná adresa výrobce ▪

Producentens firmanavn og fulde adresse ▪ Bedrijfsnaam en volledig adres van de fabrikant ▪ Tootja ärinimi ja täielik aadress ▪

Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des Herstellers ▪

Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo completo del fabbricante ▪

Uzņēmuma nosaukums un pilna ražotāja adrese ▪ Verslo pavadinimas ir pilnas gamintojo adresas ▪ Isem kummerċjali u indirizz sħiħ tal-fabbrikant ▪

Nazwa firmy i pełny adres producenta ▪ Nome da empresa e endereço completo do fabricante ▪ Denumirea comercială şi adresa completă a producătorului ▪

Obchodný názov a úplná adresa výrobcu ▪ Naziv podjetja in polni naslov proizvajalca ▪ Nombre de la empresa y dirección completa del fabricante ▪

Tillverkarens företagsnamn och kompletta adress

Jacobsen, A Textron Company

11524 Wilmar Blvd.

Charlotte, NC 28273, USA

Description and identification of the partly completed machinery. ▪ Описание и идентификация на частично завършените машини. ▪ Popis a identifikace částečně dokončeného strojního zařízení. ▪

Beskrivelse og identifikation af den delvist fremstillede maskine. ▪ Beschrijving en identificatie van de gedeeltelijk voltooide machinerie. ▪ Osaliselt komplekteeritud masina kirjeldus ja määratlus. ▪

Osittain kootun laitteiston kuvaus ja määrittely. ▪ Description et identification de la quasi-machine. ▪ Bezeichnung und Identifizierung der teilgefertigten Vorrichtung ▪ Περιγραφή και προσδιορισμός ημιτελούς μηχανήματος. ▪

A részlegesen megépített gép leírása és meghatározása. ▪ Descrizione e identificazione della quasi-macchina ▪ Da ļēji pabeigtas iekārtas apraksts un identifikācija. ▪ Dalinai užbaigtos įrangos aprašymas ir identifikacija. ▪

Deskrizzjoni u identifikazzjoni tal-makkinarju li jkun lest parzjalment. ▪ Opis i oznaczenie częściowo ukończonego urządzenia ▪ Descriç ão e identificação do equipamento parcial ▪

Descrierea şi identificarea echipamentului finalizat parţial ▪ Opis a identifikácia podzostavy strojného zariadenia ▪ Opis in identifikacija delno dokončanega stroja. ▪ Descripción e identificación de la maquinaria parcialmente completada. ▪

Beskrivning och identifiering av maskindelarna.

Product Code Serial Number Description

62834 6283401651 ~ 6283402999

GP400 22 in. (559 mm) 7 Blade TrueSet

™

Reel

62835 6283501651 ~ 6283502999

GP400 22 in. (559 mm) 9 Blade TrueSet

™

Reel

62836 6283601651 ~ 6283602999 GP400 22 in. (559 mm) 11 Blade TrueSet

™

Reel

62849 6284901651 ~ 6284902999 GP400 22 in. (559 mm) 15 Blade TrueSet

™

Reel

We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery. This shall be by hardcopy and shall be without prejudice to the intellectual property rights of the

manufacturer of the partly completed machinery.

Ние обещаваме да предадем, в отговор на основателно искане от националните органи, съответна информация за частично завършените машини. Това ще се осъществи чрез документ и няма да бъде в нарушение на правата за

интелектуална собственост на производителя на частично завършените машини.

Zavazujeme se na základě zdůvodněné žádosti ze strany národních úřadů poskytnout příslušné informace o částečn

ě dokončeném strojním zařízení. Informace budou předány v tištěné podobě a nepoškodí práva k duševnímu vlastnictví výrobce

týkající se částečně dokončeného strojního zařízení.

Som svar på en begrundet anmodning fra de nationale myndigheder forpligter vi os til at videregive oplysninger om den delvist fremstillede maskine. Dette bliver gjort i papirudgave og med forbehold for de immaterielle rettigheder, som indehaves af

producenten af den delvist fremstillede maskine.

We zijn van plan, in reactie op een redelijk verzoek van de nationale autoriteiten, relevante informatie over de gedeeltelijk voltooide machinerie te verzenden. Dit wordt gedaan in de vorm van fysieke kopieën en deze kopieën zullen onder alle

voorbehoud behoren tot de intellectuele eigendomsrechten van de fabrikant van de gedeeltelijk voltooide machinerie.

Me kohustume riigisiseste asutuste põhjendatud nõudmisel edastama asjakohast teavet osaliselt komplekteeritud masina kohta. Andmed edastatakse paberkandjal ning sellega ei tohi piirata osaliselt komplekteeritud masina tootja õigusi intellektuaalsele

omandile.

Sitoudumme toimittamaan osittain koottua laitteistoa koskevat olennaiset tiedot vastineena kansallisten viranomaisten perusteltuun pyyntöön. Tiedot toimitetaan paperitulosteena. Ne eivät rajoita valmistajan osittain koottua laitteistoa koskevia

immateriaalioikeuksia.

Nous nous engageons à fournir, en réponse à une demande rationnelle des autorités nationales, toute information appropriée concernant la quasi-machine. Ceci se fera par copie papier et sans préjuger des droits de propriété intellectuelle du fabricant

de la quasi-machine.

Wir verpflichten uns, auf eine begründete Aufforderung durch die nationalen Behörden hin, relevante Informationen über die teilgefertigte Maschine zu übersenden. Diese werden als Ausdruck übersandt und dürfen sich nicht nachteilig auf die Rechte

am geistigen Eigentum des Herstellers der teilgefertigten Maschine auswirken.

Αναλαμβάνουμε να μεταβιβάσουμε, προς απάντηση εύλογης αίτησης των εθνικών αρχών, τις σχετικές πληροφορίες όσον αφορά το ημιτελές μηχάνημα. Αυτό θα πρέπει να γίνει γραπτώς και δίχως να θίγει τα πνευματικά

δικαιώματα του κατασκευαστή

του ημιτελούς μηχανήματος.

Vállaljuk, hogy átadjuk – a nemzeti hatóságok megalapozott kérésére válaszul – a részlegesen megépített gépre vonatkozó információkat. Az információkat nyomtatott példányban adjuk át. A nyomtatott példány átadása a részlegesen megépített gép

gyártójának szellemi tulajdonjogaira tett kötelezettség nélkül történik.

Ci impegniamo a trasmettere, in risposta ad una richiesta adeguatamente motivata delle autorità nazionali, informazioni pertinenti sulla quasi-macchina. L’impegno sarà redatto in forma cartacea e lascerà impregiudicati i diritti di proprietà intellettuale del

fabbricante della quasi-macchina.

Atsaucoties uz pamatotu valsts iestāžu pieprasījumu, mēs apņemamies nodot saistīto informāciju par daļēji pabeigtu iekārtu. Tā būs cietā kopija un neradīs kaitējumus daļēji pabeigtās iekārtas ražotāja intelektuālā īpašuma tiesībām.

Atsakydami į nacionalinių valdžios organų užklausą, pateikiame informaciją apie dalinai užbaigtus mechanizmus. Šis dokumentas yra atspausdintas elektroninio originalo variantas ir be jokio išankstinio nusistatymo neturi tikslo pažeisti dalinai užbaigto

mechanizmo gamintojo intelektualinės nuosavybės teisių.

Aħna nwiegħdu li nippreżentaw, meta mitlubin mill-awtoritajiet nazzjonali, l-informazzjoni relevanti dwar il-makkinarju li jkun lest parzjalment. Din l-informazzjoni għandha tkun f’forma stampata u mingħajr preġudizzju għad-drittijiet tal-proprjetà intelletwali

tal-fabbrikant tal-makkinarju li jkun lest parzjalment.

Na uzasadnioną pro

śbę instytucji państwowych zobowiązujemy się do przekazania wszelkich informacji na temat częściowo ukończonego urządzenia. Będą one przekazane na piśmie. Strona przekazująca w/wym. dokumentację nie będzie rościła sobie

żadnych praw do własności intelektualnej producenta częściowo ukończonego urządzenia.

Na sequência de pedido razoável por parte das autoridades nacionais, comprometemo-nos a transmitir informações importantes sobre o equipamento parcial. Tal será feito por meio de hardcopy

e sem prejuízo para os direitos de propriedade intelectual do fabricante do equipamento parcial.

Ne angajăm să transmitem, ca răspuns la o solicitare motivată a autorităţilor naţionale, informaţii relevante privind echipamentul finalizat parţial. Aceasta se va efectua în format hârtie şi fără a aduce atingere drepturilor de proprietate intelectuală ale

producătorului echipamentului finalizat parţial.

Zaväzujeme sa, že na základe odôvodnenej požiadavky národných orgánov predložíme dôležité informácie o podzostave strojného zariadenia.

Musí to byť v tlačenej forme a bez ujmy na právach duševného vlastníctva výrobcu podzostavy strojného zariadenia.

Zavezujemo se, da bomo na utemeljeno zahtevo nacionalnih organov predložili zadevne informacije o delno dokončanem stroju. Informacije bodo v tiskani obliki in ne bodo posegale v pravice intelektualne lastnine proizvajalca delno dokončanega stroja.

Nos comprometemos a transmitir, en respuesta a una petición razonada por parte de las autoridades nacionales, información relevante sobre la maquinaria parcialmente completada. Ésta será transmitida en copia impresa y no afectará a los derechos

de propiedad intelectual del fabricante de la maquinaria parcialmente completada.

Vi åtar oss att vidarebefordra relevant information om maskindelarna vid en motiverad förfrågan från nationella myndigheter. Informationen ska erhållas i form av papperskopior och ska vara utan men för maskindelstillverkarens immateriella rättigheter.

2 SPECIFICATIONS

Partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of Directive 2006/42/EC.

Частично завършените машини не трябва да бъдат пускана в употреба, докато крайните машини, в които са вградени, не са приведени в съответствие с постановленията на директива 2006/

42/EО.

Částečně dokončené zařízení nesmí být uvedeno do provozu, dokud konečné zařízení, do kterého bylo uvedené zařízení namontováno, neodpovídá ustanovením Směrnice č. 2006/42/EC.

Delvist fremstillede maskiner må ikke indsættes i driften, før den endelige maskine, som den skal inkorporeres i, er blevet erklæret I overensstemmelse med bestemmelserne i Direktiv 2006/42/EF.

Gedeeltelijk voltooide machinerie mag niet in dienst worden genomen, totdat er voor de definitieve machinerie, waarvan gedeeltelijk voltooide machinerie onderdeel uitmaakt, een conformiteitsverklaring

is ontvangen onder de voorwaarden van Richtlijn 2006/42/EG.

Osaliselt komplekteeritud masinat ei tohi kasutusele võtta enne, kui lõplikult komplekteeritud masin, millega see ühendatakse, on tunnistatud direktiivi 2006/42/EÜ sätetele vastavaks.

Osittain koottua laitteistoa ei saa ottaa käyttöön, ennen kuin lopullinen laitteisto, johon se asennetaan, on vakuutettu direktiivin 2006/42/EY säännösten mukaiseksi.

La quasi-machine ne doit pas être mise en service avant que la machine finale dans laquelle elle doit être incorporée n’ait été déclarée conforme aux dispositions de la directive 2006/42/CE

Die teilgefertigte Vorrichtung darf erst in Betrieb genommen werden, wenn die Konformität der Maschine, in die sie eingebaut wird, entsprechend den Bestimmungen der Richtlinie 2006/42/EG erklärt

worden ist.

Θα πρέπει να εκτελεστεί σέρβις

στο ημιτελές μηχάνημα μέχρι το τελικό μηχάνημα στο οποίο θα ενσωματωθεί να έχει τη δήλωση συμμόρφωσης, σύμφωνα με τις διατάξεις της Οδηγίας 2006/42/ΕΚ.

A részlegesen megépített gépet tilos üzembe helyezni mindaddig, amíg a 2006/42/EK irányelv rendelkezéseivel összhangban a részlegesen megépített gépet be nem építik a végleges változatba, és

erről nem nyilatkoznak.

La quasi-macchina non deve essere messa in servizio finché la macchina finale in cui deve essere incorporata non è stata dichiarata conforme, nel caso, alle disposizioni della Direttiva 2006/42/CE.

Daļēji pabeigtu iekārtu nedrīkst nodot ekspluatācijā, līdz galīgā iekārta, kurā tā ir jāiebūvē, ir deklarēta atbilstoši direktīvas Nr. 2006/42/EK noteikumiem.

Dalinai užbaigto mechanizmo negalima paleisti kol kiti mechanizmai, kurie dar bus prijungti, nebus patvirtinti kaip atitinkantys 2006/42/EC Direktyvos reikalavimus.

Il-makkinarju li jkun parzjalment lest ma g ħandux jibda jitħaddem sakemm il-makkinarju finali li fih ikun se ji ġi inkorporat ikun ġie ddikjarat konformi mad-dispożizzjonijiet tad-Direttiva 2006/42/KE.

Urzą

dzenia częściowo ukończonego nie wolno użytkować aż do orzeczenia zgodności urządzenia w postaci kompletnej z wymaganiami dyrektywy 2006/42/WE.

O equipamento parcial não poderá entrar em funcionamento antes do mecanismo final no qual vai ser incorporado ser declarado como estando em conformidade com as condições da Directiva 2006/

42/CE.

Echipamentul finalizat parţial nu trebuie pus în funcţiune până ce echipamentul final în care va fi încorporat nu este declarat ca fiind conform cu prevederile Directivei 2006/42/CE.

Podzostava strojného zariadenia nesmie byť uvedená do prevádzky, pokiaľ finálne strojné zariadenie, ktorého sa stane súčasťou, nebude vyhlásené ako zhodné s ustanoveniami smernice 2006/42/ES.

Delno dokončanega stroja ni dovoljeno dati v obratovanje, dokler se dokončani stroj, v katerega se vgradi delno dokončani stroj, ne potrdi kot skladen z določbami Direktive 2006/42/ES.

La maquinaria parcialmente completada no debe ponerse en servicio hasta que la maquinaria final a la que debe incorporarse cumpla con las provisiones de la Directiva 2006/42/CE.

Maskindelarna får ej tas i bruk förrän maskinen som delen tillhör har deklarerats som överensstämmande med föreskrifterna I direktivet 2006/42/EG.

These accessories have been

designed to be fitted to the Jacobsen

GP400 mowers.

The place and date of the declaration ▪ Място и дата на декларацията ▪ Místo a datum prohlášení ▪ Sted og dato for erklæringen ▪

Plaats en datum van de verklaring ▪ Deklaratsiooni väljastamise koht ja kuupäev ▪ Vakuutuksen paikka ja päivämäärä ▪ Lieu et date de la déclaration ▪

Ort und Datum der Erklärung ▪ Τόπος και ημερομηνία δήλωσης ▪ A nyilatkozat kelte (hely és idő) ▪ Luogo e data della dichiarazione ▪

Deklarācijas vieta un datums ▪ Deklaracijos vieta ir data ▪ Il-post u d-data tad-dikjarazzjoni ▪ Miejsce i data wystawienia deklaracji ▪ Local e data da declaração ▪ Locul şi data declaraţiei ▪ Miesto a dátum

vyhlásenia ▪ Kraj in datum izjave ▪ Lugar y fecha de la declaración ▪ Plats och datum för deklarationen

Jacobsen, A Textron Company

11524 Wilmar Blvd.

Charlotte, NC 28273, USA

Sept 1st, 2012

Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is established in

the Community.

Подпис на човека, упълномощен да състави декларацията от името на производителя, който поддържащ техническата документация и е оторизиран да изготви техническия файл и е

регистриран в общността.

Podpis osoby oprávněné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávněné sestavit technické soubory a založené v rámci Evropského společenství.

Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er

baseret i nærområdet.

Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is

gevestigd in het Woongebied.

Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus koostada tehniline toimik.

Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön.

Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et qui est implantée dans la Communauté.

Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen

zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.

Υπογραφή ατόμου εξουσιοδοτημένου για την σύνταξη της δήλωσης εκ μέρους του

κατασκευαστή, ο οποίος κατέχει την τεχνική έκθεση και έχει την εξουσιοδότηση να ταξινομήσει τον τεχνικό φάκελο και

ο οποίος είναι διορισμένος στην Κοινότητα.

A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a műszaki dokumentációt őrzi, engedéllyel rendelkezik a műszaki fájl összeállításához, és aki a közösségben

letelepedett személy.

Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita

nella Comunità.

Tās personas paraksts, kura ir pilnvarota deklarācijas sastādīšanai ražotāja vārdā, kurai ir tehniskā dokumentācija, kura ir pilnvarota sagatavot tehnisko reģistru un kura ir apstiprināta Kopienā.

Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikė įgaliojimus sudaryti šią deklaraciją, ir kuris ją pasirašė, turi visą techninę informaciją ir yra įgaliotas sudaryti technin

ės informacijos dokumentą.

Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, għandha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-Komunità.

Podpis osoby upoważnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentację techniczną, upoważnioną do stworzenia dokumentacji technicznej oraz wyznaczonej ds.

wspólnotowych.

Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar o processo técnico e que está estabelecida na

Comunidade.

Semnătura persoanei împuternicite să elaboreze declaraţia în numele producătorului, care deţine documentaţia tehnică, este autorizată să compileze dosarul tehnic şi este stabilită în Comunitate.

Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracovať technické podklady a ktorá je umiestnená v Spoločenstve.

Podpis osebe, pooblaščene za izdelavo izjave v imenu proizvajalca, ki ima tehnično dokumentacijo in lahko sestavlja spis tehnične dokumentacije, ter ima sedež v Skupnosti.

Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el archivo técnico y que está establecido en la

Comunidad.

Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att sammanställa den tekniska informationen och

som är etablerad i gemenskapen.

2006/42/EC Annex II 1.A.2

Tim Lansdell

Technical Director

Ransomes Jacobsen Limited

West Road, Ransomes Europark,

Ipswich, IP3 9TT, England

2006/42/EC Annex II 1.A.10

Vasant Godhalekar

VP of Engineering

January 31st, 2011

Jacobsen, A Textron Company

11524 Wilmar Blvd,

Charlotte, NC 28273, USA

Certificate Number ▪ Номер на сертификат ▪ Číslo osvědčení ▪ Certifikatnummer ▪ Certificaatnummer ▪ Sertifikaadi number ▪ Hyväksyntänumero ▪

Numéro de certificat ▪ Bescheinigungsnummer ▪ Αριθμός Πιστοποιητικού ▪ Hitelesítési szám ▪ Numero del certificato ▪ Sertifikāta numurs ▪

Sertifikato numeris ▪ Numru taċ-Ċertifikat ▪ Numer certyfikatu ▪ Número do Certificado ▪ Număr certificat ▪ Číslo osvedčenia ▪ Številka certifikata ▪

Número de certificado ▪ Certifikatsnummer

4258371 Rev A

GB BG CZ DK NL EE FI FR DE GR HU

IT LV LT MT PL PT RO SK SI ES SE

българскиEnglish čeština dansk Nederlands eesti suomi français Deutsch Ελληνικά magyar

latviešu

valoda

italiano lietuvių

kalba

Malki polski português Română slovenčina slovenščina Ελληνικά Svenska

SETUP 3

3 SETUP

3.1 FRONT ROLLER AND ACCESSORIES ________________________________________

The front roller is not included with the reel assembly and

must be ordered separately. Check with your dealer for

front rollers that are available for your unit. Follow

installation instructions included with the front roller.

Other accessories may also be available for your reel such

as Turf Groomer®, roller scrapers, and roller brushes.

Install these accessories before installing reels.

Follow instructions included in your mower’s manuals and/

or Turf Groomer’s Instruction Sheet for adjusting the reel to

bedknife and height of cut.

3.2 MOUNTING THE CUTTING UNITS ____________________________________________

1. Manually raise lift arms and slide reel into place.

2. Secure lift arm (A) to reel using two shoulder bolts (B).

3. Follow directions given with motor adapter kits for

assembling motor to reels.

Figure 1

4 ADJUSTMENTS

4.1 GENERAL________________________________________________________________

1. Adjustments and maintenance should always be

performed by a qualified technician. If proper

adjustment cannot be made, contact an authorized

Jacobsen Dealer.

2. Replace, do not adjust, worn or damaged

components.

3. Long hair, jewelry or loose fitting clothing may get

tangled in moving parts.

4. Do not change speed limit settings or overspeed the

drive motors.

4.2 BEDKNIFE-TO-REEL _______________________________________________________

(Pre-adjustment Check)

1. Check the reel bearings for end play or radial play.

There should be no end play or radial play. See Section

4.9.

2. Inspect the reel blades and bedknife to insure good

sharp edges without bends or nicks.

a. The leading edge of the reel blades must be sharp,

free of burrs and show no signs of rounding off.

b. The bedknife and bedknife backing must be

securely tightened. The bedknife must be straight

and sharp.

c. A flat surface of at least 1/32 in. (0.8 mm) minimum

must be maintained on the front face of the bed-

knife. Use a standard flat file to dress the bedknife.

3. If wear or damage is beyond the point where the reel

or bedknife can be corrected by the lapping process,

they must be reground.

4. Proper reel-to-bedknife adjustment is critical. A gap of

0.001 to 0.003” (0.025 to 0.076 mm) must be

maintained across the entire length of the reel and

bedknife.

5. The reel must be parallel to the bedknife. An

improperly adjusted reel will lose its sharp edges

prematurely and may result in serious damage to the

reel and bedknife.

6. Grass conditions will also affect the adjustment.

a. Dry, sparse conditions will require a wider gap to

prevent heat buildup and damage to the reel and

bedknife.

b. High quality grass with a good moisture content

requires a closer gap (near zero).

Figure 4A

Figure 4B

WARNING

Before you clean, adjust, or repair this equipment,

disengage all drives, lower implements to the ground,

turn system power off, remove key from ignition switch,

and disconnect battery pack(s) to prevent injuries

Make sure the mower is parked on a solid and level

surface. Never work on a mower that is supported only

by the jack. Always use jack stands.

CAUTION

Be careful to prevent entrapment of the hands and

fingers between moving and fixed components of the

machine.

CAUTION

To prevent personal injury and damage to the cutting

edges, wear gloves and handle the reel and bedknife

with extreme care.

1/32”

(0.8 mm)

Leading Edge

ADJUSTMENTS 4

4.3 BEDKNIFE ADJUSTMENT ___________________________________________________

1. Read Section 4.1 before making the adjustment.

2. Start adjustment at the leading end of the reel,

followed by the trailing end.

The leading end of the

reel blades is that end which passes over the

bedknife first during normal reel rotation.

3. Use adjusters (B and C), to adjust gap. Rotate

adjusters (Clockwise) to close gap. Each click of the

adjuster moves the bedknife 0.001” (0.025 mm)

closer to the reel.

a. Slide a feeler gauge or shim stock 0.001” - 0.003”

(0.025 - 0.075 mm) between the reel blade and

the bedknife. Do not turn the reel.

b. Adjust the trailing end of the reel to the same

gap in a similar manner then recheck the

adjustment at the leading end.

c. When the reel is properly adjusted to the

bedknife, the reel will spin freely and you should

be able to cut a piece of newspaper, along the

full length of the reel, when the paper is held at

90° to the bedknife.

Figure 4C

4.4 CUTTING HEIGHT _________________________________________________________

Note:

Always make the reel to bedknife adjustment

before adjusting height of cut. (Sections 4.2 and 4.3)

4. Set desired cutting height on the gauge (E).

a. Measure distance between the underside of

screw head and gauge block surface (F).

b. Adjust screw (H) to obtain desired height then

tighten the wing nut.

5. Loosen the nuts on the front roller brackets (G) just

enough to allow the adjuster knob (K) to raise or

lower the front roller.

6. Place gauge (E) across bottom of front and rear

rollers near one end of roller.

7. Slide the head of gauge screw (H) over the bedknife

(L) and adjust the knob (K) to close the gap between

the screw head and bedknife. Then tighten locknut

(G).

8. Repeat Steps 4 and 5 on opposite end. Complete

adjustment to one end before adjusting opposite end.

9. Tighten nuts (G) and recheck each end.

Figure 4D

NOTICE

Avoid excessive tightening or serious damage may

result to bedknife and reel blades. Reels must turn

freely.

4 ADJUSTMENTS

4.5 REEL BEARING ___________________________________________________________

Any radial play or excessive end play indicates bad

bearings, a weak tension spring or a backed off nut.

1. Check bearing housing mounting hardware. Tighten

or replace components as required. Carefully clean

threads with degreaser.

2. Apply a medium strength grade of Loctite to nut (P),

then thread nut onto the reel shaft until the nut is

1-27/32” (46 mm) from the end of the reel shaft.

3. Fill reel bearing housings with NLGI - Grade O

grease after adjusting spring.

Figure 4E

4.6 BEDKNIFE ADJUSTER SPRING______________________________________________

For proper operation, bedknife adjuster spring should be

compressed to a dimension of 1-7/16 - 1-1/2 in. (36.5-38

mm).

To adjust spring compression, loosen or tighten nut (R) to

obtain a distance of 1-7/16 - 1-1/2 in. (36.5-38 mm).

After adjusting spring, check reel to bedknife adjustment.

Figure 4F

4.7 BEDKNIFE ADJUSTER TENSION_____________________________________________

Remove cotter pin (U) and fully loosen, then tighten

slotted nut (S) to remove clearance (no end play)

between components. Continue to tighten nut until next

slot in nut aligns with hole in bedknife adjuster rod (T).

Install new cotter pin.

Check torque required to rotate adjuster rod (T).

Maximum torque should be 24 in. lb. (2 ft. lb.) (2.7 Nm).

After adjusting nut, check reel to bedknife adjustment.

Figure 4G

4.8 GRINDING BEDKNIFE ______________________________________________________

Bedknife can be lowered out of the reel for grinding

without completly removing the bedknife assembly.

1. Remove cotter pin (U), slotted nut (S), bellville

washer (V), shim washer (W-If required), and half

trunnion (X). See Figure 4G

4. Press down on adjuster end of rod (T) to rotate other

end of the adjuster out of the bedknife finger.

5. Rotate bedknife backing to access the reel and

bedknife for grinding.

6. After grinding, assemble bedknife using reverse

order of removal. Check adjustment of bedknife

adjuster tension (Section 4.7), and reel to bedknife

adjustment (Section 4.3).

1-27/32”

(46 mm)

1-7/16 to 1-1/2 in.

(36.5 to 38 mm)

NOTICE

Overtightening slotted nut (S) will make bedknife

adjuster rod (T) difficult to adjust.

ADJUSTMENTS 4

4.9 TORQUE SPECIFICATION ___________________________________________________

Jacobsen uses Grade 5 Plated bolts as standard, unless otherwise noted. For tightening plated bolts, use the value

given for lubricated.

NOTICE

All torque values included in these charts are approximate and are for reference only. Use of these torque values is

at your sole risk. Jacobsen is not responsible for any loss, claim, or damage arising from the use of these charts.

Extreme caution should always be used when using any torque value.

AMERICAN NATIONAL STANDARD FASTENERS

SIZE UNITS GRADE 5 GRADE 8 SIZE UNITS GRADE 5 GRADE 8

Lubricated Dry Lubricated Dry Lubri-

cated

Dry Lubri-

cated

Dry

#6-32 in-lb (Nm) – 20 (2.3) – – 7/16-14 ft-lb (Nm) 37 (50.1) 50 (67.8) 53 (71.8) 70 (94.9)

#8-32 in-lb (Nm) – 24 (2.7) – 30 (3.4) 7/16-20 ft-lb (Nm) 42 (56.9) 55 (74.6) 59 (80.0) 78 (105)

#10-24 in-lb (Nm) – 35 (4.0) – 45 (5.1) 1/2-13 ft-lb (Nm) 57 (77.2) 75 (101) 80 (108) 107 (145)

#10-32 in-lb (Nm) – 40 (4.5) – 50 (5.7) 1/2-20 ft-lb (Nm) 64 (86.7) 85 (115) 90 (122) 120 (162)

#12-24 in-lb (Nm) – 50 (5.7) – 65 (7.3) 9/16-12 ft-lb (Nm) 82 (111) 109 (148) 115 (156) 154 (209)

1/4-20 in-lb (Nm) 75 (8.4) 100 (11.3) 107 (12.1) 143 (16.1) 9/16-18 ft-lb (Nm) 92 (124) 122 (165) 129 (174) 172 (233)

1/4-28 in-lb (Nm) 85 (9.6) 115 (13.0) 120 (13.5) 163 (18.4) 5/8-11 ft-lb (Nm) 113 (153) 151 (204) 159 (215) 211 (286)

5/16-18 in-lb (Nm) 157 (17.7) 210 (23.7) 220 (24.8) 305 (34.4) 5/8-18 ft-lb (Nm) 128 (173) 170 (230) 180 (244) 240 (325)

5/16-24 in-lb (Nm) 173 (19.5) 230 (26.0) 245 (27.6) 325 (36.7) 3/4-10 ft-lb (Nm) 200 (271) 266 (360) 282 (382) 376 (509)

3/8-16 ft-lb (Nm) 23 (31.1) 31 (42.0) 32 (43.3) 44 (59.6) 3/4-16 ft-lb (Nm) 223 (302) 298 404 315 (427) 420 (569)

3/8-24 ft-lb (Nm) 26 (35.2) 35 (47.4) 37 (50.1) 50 (67.8) 7/8-14 ft-lb (Nm) 355 (481) 473 (641) 500 (678) 668 (905)

METRIC FASTENERS

SIZE UNITS

Non Critical

Fasteners

into

Aluminum

Lubricated Dry Lubricated Dry Lubricated Dry Lubricated Dry

M4 Nm (in-lb) – – – – – – 3.83 (34) 5.11 (45) 2.0 (18)

M5 Nm (in-lb) 1.80 (16) 2.40 (21) 4.63 (41) 6.18 (54) 6.63 (59) 8.84 (78) 7.75 (68) 10.3 (910 4.0 (35)

M6 Nm (in-lb) 3.05 (27) 4.07 (36) 7.87 (69) 10.5 (93) 11.3 (102) 15.0 (133) 13.2 (117) 17.6 (156) 6.8 (60)

M8 Nm (in-lb) 7.41 (65) 9.98 (88) 19.1 (69) 25.5 (226) 27.3 (241) 36.5 (323) 32.0 (283) 42.6 (377) 17.0 (150)

M10 Nm (ft-lb) 14.7 (11) 19.6 (14) 37.8 (29) 50.5 (37) 54.1 (40) 72.2 (53) 63.3 (46) 84.4 (62) 33.9 (25)

M12 Nm (ft-lb) 25.6 (19) 34.1 (25) 66.0 (48) 88.0 (65) 94.5 (70) 125 (92) 110 (81) 147 (108) 61.0 (45)

M14 Nm (ft-lb) 40.8 (30) 54.3 (40) 105 (77) 140 (103) 150 (110) 200 (147) 175 (129) 234 (172) 94.9 (70)

4.6

8.8

10.9

12.9

4127335

4181863

GP400 REEL

5.1 Outer Reel

Serial No. All

> Change from previous revision

GP400 REEL

Item Part No. Qty. Description Serial Numbers/Notes

REF 1 Inner Reel See 6.1

2 1002224 2 Zerk Bolt

3 1004990 1 22” Rear Roller See 7.1

4 2810043 1 Shield, Grass

5 4181863 1 Decal, Read Manual for Service

6 4127335 2 Decal, Danger

7 3010293 1 Stop, Reel

8 403782 2 Screw, 1/4-20 x 3/4” Truss Head

9 453023 2 Flat Washer, 1/4

10 446130 4 Lockwasher, 1/4 Heavy

11 443102 4 Nut, 1/4-20 Hex

12 3008438 1 Bracket, Right SIde Front Roller

13 3008439 1 Bracket, Left Side Front Roller

14 441674 2 Carriage Bolt, 5/16-18 x 1-3/4”

15 445795 4 Nut, 5/16-18 Spiralock Flange

16 343616 2 Stud, Front Roller Adjuster

17 3005692 2 Knob, Front Roller Adjuster

18 367164 1 Spacer

19 453011 1 Flat Washer, 3/8

20 446142 1 Lockwasher, 3/8 Heavy

21 400294 1 Screw, 3/8-24 x 1” Hex Head

22 REF 1 Front Roller Not included with reel.

23 352737 2 Set Screw, 1/4-20 x 7/8” Grade 8

24 365247 2 Shoulder Bolt

25 400184 2 Screw, 5/16-18 x 3/4” Hex Head

26 2000065 1 Casting, Counterweight

27 400110 2 Screw, 1/4-20 x 7/8” Hex Head

Optional MagKnife Bedknives

Part Number Description

4131369 22” High Profile

4131001 22” Low Profile

4131370 22” Tournament

4131003 22” Super Tournament

Standard Style Bedknives

(Secured with screws)

Part Number Description

◆ 503478 22” Low Profile

503477 22” High Profile

503479 22” Tournament

4234900 22” Championship

▲ 5003150 22” Medium Section

● 5002887 22” Super Tournament

▲ Standard Bedknife (7 Blade)

◆ Standard Bedknife (9 Blade)

● Standard Bedknife (11 and 15 Blade)

GP400 REEL

6.1 Inner Reel

Serial No. All

> Change from previous revision

GP400 REEL

Item Part No. Qty. Description Serial Numbers/Notes

4256225 1 22” Reel Frame

2 5003053 1 Reel, 22” 7 Blade

2 5001099 1 Reel, 22” 9 Blade

2 5001101 1 Reel, 22” 11 Blade

2 4225505 1 Reel, 22” 15 Blade

3 1000480 1 Housing, Bearing

4 500534 1 • Bearing, Cup and Cone

5 336962 1 • Seal, Grease

6 471214 1 • Grease Fitting

7 471240 1 • Vent Fitting

8 1004756 1 Housing, Bearing Includes Items 4~7

9 400104 4 Screw, 1/4-20 x 1/2” Hex Head

10 446130 4 Lockwasher, 1/4 Heavy

11 400192 8 Screw, 5/16-18 x 1-1/2” Socket Head

12 453009 4 Flat Washer, 5/16

13 445795 8 Nut, 5/16-18 Spiralock Flange

14 458013 1 Ring, Snap

15 5002151 1 Spring, Compression

16 304745 1 Washer, Reel Shaft

17 364900 1 Nut, 3/4-16 Reel

18 163892 1 Seal Assembly

19 4255754 1 Backing, 22” Bedknife

20 See Chart 1 Bedknife

21 4252470 AR Screw, Bedknife Package of 100 Screws

22 315298 2 Bolt, 7/16-20 x 3/4” Wheel

23 4256228 2 Rod, Bedknife Adjuster

24 4256227 2 Trunnion, Internal

25 4256229 2 Cradle, Tube Spring

26 4256231 2 Spring, Compression

27 400051 2 Washer, 1/2” Bellville

28 400050 2 Nut, 1/2-20 Hex Jam Nylock

29 4256233 2 Washer, Bedknife Adjustment

30 4256232 2 Trunnion Half

31 400052 2 Washer, 5/16 Bellville

32 400065 AR Washer, Shim

33 400053 2 Nut, 5/16-24 Hex Slotted

34 460008 2 Cotter Pin, 5/64 x 3/4”

35 4256230 2 Spring, Detent

> Change from previous revision

GP400 REEL

7.1 Rear Roller

1004990

Serial No. All

Item Part No. Qty. Description Serial Numbers/Notes

1004990 1 22” Rear Roller

1 3010422 1 • Shaft, 22” Roller

2 5002814 1 • Tube, 22” Roller

3 3010712 2 • Bearing, Ball

4 3010286 2 • Seal

> Change from previous revision

GP400 REEL

Item Part No. Qty. Description Serial Numbers/Notes

68613 1 22” Machined Grooved Steel

68614 1 22” Machined Grooved Aluminum

1 3009725 1 • Shaft, 22” Roller

2 5002815 1 • Roller, 22” Grooved Steel Used on 68613

2 3000394 1 • Roller, 22” Grooved Aluminum Used on 68614

3 503378 2 • Bearing, Cup and Cone

4 367029 2 • Locknut, 3/4-16

5 3010210 2 • Adapter, Seal

8.1 Machined Grooved Roller

68613 and 68614

Serial No. All

> Change from previous revision

GP400 REEL

Item Part No. Qty. Description Serial Numbers/Notes

1004991 1 22” Solid Front Roller (Light)

1004988 1 22” Solid Front Roller

1 3010621 1 • Shaft, 22” Roller

2 5002814 1 • Roller, 22” Solid (Light) Used on 1004991

2 3007008 1 • Roller, 22” Solid Used on 1004988

3 3010712 2 • Bearing, Ball

4 3010286 2 • Seal

5 471214 2 • Fitting, Grease

68530 1 22” Solid Front Roller with Scraper Includes 1004991

68641 1 22” Solid Front Roller with Scraper Includes 1004988

6 2500022 1 • Scaper Assembly

7 352214 2 • • Clip

8 407586 2 • • 1/4-20 Pan Head Screw

9.1 Solid Front Roller

68530 and 68641

Serial No. All

Pagina se încarcă...

Ransomes 62834, 62835, 62836, 62849 Accessories Manual

Marca: Ransomes

Model: 62834, 62835, 62836, 62849

Tip: Accessories Manual

Descărcați PDF

raport

în alte limbi

English: Ransomes 62834, 62835, 62836, 62849

Ransomes 62834, 62835, 62836, 62849 Accessories Manual

Ransomes 62834, 62835, 62836, 62849 Accessories Manual

în alte limbi

Lucrări înrudite

Alte documente