Ransomes USAG004 / USAD004 / 62706 Manualul proprietarului

Marca: Ransomes

Model: USAG004 / USAD004 / 62706

Categorie: Cositoare

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

United

Kingdom

When Performance Matters.

™

Safety, Operation and Maintenance Manual

Jacobsen GP400™ Ride on Greens Mower

Engine Range - Kubota D722-E3B D722-E4B

Briggs and Stratton Vanguard 350447

GP400 Gasoline / Series: GZ / Product code:USAG004

GP400 Gasoline (USA only) / Product code:62706

GP400 Diesel (Kubota E3B) / Series: GY / Product code:USAD004

GP400 Diesel (Kubota E4B) / Series: GY4 / Product code:USAD004

GP400 Diesel (Kubota E4B) / Series: GY5 / Product code:USAD004

WARNING

WARNING: If incorrectly used this machine can cause severe

injury. Those who use and maintain this machine must be

trained in its proper use, warned of its dangers and must read

the entire manual before attempting to set up, operate, adjust

or service the machine.

25000G-GB (rev.6)

RJL 100 July 2018

1 CONTENTS

Ransomes Jacobsen Limited reserves the right to make design changes without obligation to make these

changes on units previously sold and the information contained in this manual is subject to change without notice.

INTRODUCTION

Important ....................................................................................3

Product Identification ..................................................................4

Guidelines For The Disposal Of Scrap Products .......................6

During Service Life .....................................................................6

End Of Service Life.................................................................... 6

Parts Manual ..............................................................................7

Key Numbers .............................................................................8

SAFETY

How To Operate Safely.............................................................. 9

Safe Operation ...........................................................................9

Preparation .................................................................................9

Operation ..................................................................................10

ROPS ........................................................................................11

Safe Handling Of Fuels .............................................................11

Maintenance And Storage .........................................................11

When You Put The Mower On A Trailer ....................................12

Important Safety Notes .............................................................13

SPECIFICATION

Engine Specification ..................................................................16

Dimensions & Weights ..............................................................17

Machine Specification ...............................................................18

Vibration Level ..........................................................................19

Noise Level ...............................................................................20

Slopes .......................................................................................20

Cutting Unit Specification ..........................................................21

Cutting Performance .................................................................21

Recommended Lubricants ........................................................22

Accessories ...............................................................................22

Certificates Of Conformity .........................................................23

Notes .........................................................................................27

DECALS

Safety Decals ............................................................................28

Instruction Decals ......................................................................30

Notes .........................................................................................31

CONTROLS

Operator Workstation ................................................................32

Instrument Panel .......................................................................33

Starter Key Switch .....................................................................34

Throttle Control Lever ...............................................................34

Cutting Unit Switch (PTO) .........................................................34

Engine Coolant Temperature (Diesel Only) ..............................35

Working Lights ..........................................................................35

Hour Meter ................................................................................35

Blocked Hydraulic Filter Warning Light .....................................36

Multifunction Warning Light .......................................................36

Oil Pressure Warning Light .......................................................36

Choke Control (Gasoline Only) .................................................36

Mow / Transport Lever ..............................................................37

Power Outlet .............................................................................37

Horn Button ...............................................................................37

Parking Brake ............................................................................37

Traction Pedal ...........................................................................38

Steering Wheel ..........................................................................38

Lift & Lower Rate & Synchronisation Control ............................38

Free Wheel ................................................................................39

OPERATION

Daily Inspection .........................................................................40

Operator Presence And Safety Interlock System ......................40

Operating Procedure .................................................................41

Setting Up The Machine ............................................................43

Mounting The Cutting Heads ....................................................44

Reel Motor Mounting .................................................................45

Cutting Cylinder Lift & Lower Synchronisation ..........................46

Operation Of The Machine ........................................................46

Starting The Engine ..................................................................47

Driving .......................................................................................47

Mowing Procedure ....................................................................47

To Stop The Engine ..................................................................48

How To Remove A Blockage From Cutting Units .....................48

Backlapping ...............................................................................49

Backlapping Procedure .............................................................50

Transporting On A Trailer Or Flat Bed ......................................50

Slinging And Jacking The Machine ...........................................50

Mowing On Slopes ....................................................................51

Slope Calculation Chart ............................................................53

MAINTENANCE AND LUBRICATION

Maintenance And Lubrication Chart...........................................54

Engine Lubrication - Gasoline ...................................................54

Engine Lubrication - Diesel .......................................................56

Engine Access ..........................................................................58

Engine Oil Level - Gasoline ......................................................58

Engine Oil Change- Gasoline ...................................................59

Engine Oil Filter- Gasoline ........................................................59

Air Filter - Gasoline ...................................................................60

Engine Fuel Filter - Gasoline ....................................................61

Oil Cooler Gasoline Machine ....................................................61

Air Filter - Diesel .......................................................................63

Engine: Fan Belt - Diesel ..........................................................63

Engine Coolant - Diesel ............................................................64

Oil Cooler And Radiator - Diesel ...............................................65

Bleeding The Fuel System - Diesel ...........................................66

Air Cleaner - Diesel ...................................................................67

Battery - Gas & Diesel ..............................................................67

Hydraulic System - Gas & Diesel ..............................................68

Handbrake - Gas & Diesel ........................................................69

Tyres - Gas & Diesel .................................................................69

Machine Maintenance General - Gas & Diesel .........................70

Lubrication Of Cutting Unit ........................................................70

Notes .........................................................................................71

ADJUSTMENTS

Traction Control Pedal ..............................................................72

Adjusting Speed Control Switch ................................................73

Steering Arm Adjustment ..........................................................73

Rear Swing Out Arm .................................................................74

Levelling Linkage For The Front Cutting Heads .......................75

Seat Adjustment ........................................................................76

Bedknife-to-reel Trueset™ Reel ...............................................81

Bedknife Adjustment Trueset™ Reel ........................................82

Cutting Height Trueset™ Reel ..................................................83

Reel BearTrueset™ Reel ..........................................................84

Bedknife Adjuster Spring Trueset™ Reel .................................84

Bedknife Adjuster Tension Trueset™ Reel ...............................85

Grinding Bedknife Trueset™ Reel ............................................85

Bedknife Adjustment Classic Xp™ Reels .................................86

Height Of Cut Classic Xp™ Reels ............................................87

ACCESSORIES

Three Wheel Drive Kit ...............................................................88

Paddle Kit ..................................................................................88

Dew Whip Kit ............................................................................89

Groomer Kit ...............................................................................89

Notes .........................................................................................90

PROBLEM SOLVING

Problem Solving General........................................................... 91

FUSES AND RELAYS

Fuse And Relay Identification ..................................................101

Notes ........................................................................................102

QUALITY OF CUT

Quality Of Cut Troubleshooting.................................................. 92

Washboarding............................................................................ 92

Marcelling ..................................................................................93

Step Cutting 94

Scalping ....................................................................................95

Stragglers................................................................................... 96

Streaks....................................................................................... 97

Windrowing ...............................................................................98

Rifling Or Tramlining .................................................................99

Matched Cutting Units ...............................................................99

GUARANTEE

Warranty ..................................................................................103

Service .....................................................................................103

Evaporative Emission Control Warranty Statement .................104

SECTION PAGE

en-3

SAFETY 3

3.1 IMPORTANT__________________________________________________________

The JACOBSEN GP400 is available as a Petrol or Diesel engined self propelled Reel mower. The hydraulic

systems are for the traction drive, the cutting unit lift and the lower and cutting unit drives and steering.

IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high

level.

This SAFETY AND OPERATORS MANUAL is part of the machine and must stay with the machine always.

Suppliers of both original and used machines need to keep the documentation that comes with the machine.

You must use the machine to cut the grass only and not for any other purpose. Compliance with the conditions of

operation, service and repair specified by the manufacturer, are understood to be part of the correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and

maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the machine that the manufacturer does not approve. This type of change

can release the manufacturer from the liability for any damage or injury.

Discard worn parts, taking note of the environmental result, use the systems available in the country where the

machine is used. When the machine is at its end of life, there are guidelines in this manual for the removal of the

machine from use.

Use only Ransomes Jacobsen Genuine spare parts to make sure that European conformity is controlled.

2006/42/EC

These instructions are the Original instructions confirmed by Ransomes Jacobsen Limited

en-4

3 SAFETY

MADE IN JAPAN

D722 - 00

Serial No.:

Code No.:

XXXXXXX

XXXXX-XXXXX

3.2 PRODUCT IDENTIFICATION ___________________________________________ _

A Maximum front axle load in Kg (for machines being driven

on the highway)

B Gross weight (mass) in Kg

C Maximum rear axle load in Kg (for machines being driven on

the highway)

D Power in Kw

E Date code

F Machine type (Designation)

G Product code

H Product name

J Serial number

Location of Serial number plate

The serial number plate (A) is found on the chassis under the position for the

operator seat.

Chassis Stamp

The Serial number and date code (B) are marked on the chassis under the seat plate

Engine Identification

Serial Plate

Location of Serial number plate

The engine serial number is found on the top of the valve

cover toward the front of the mower. Label shows the engine group and

serial number.

The engine serial number is also found on the engine block.

ROPS Serial Plate

West Road

Ransomes Europark

Ipswich IP3 9TT

England

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

565

13.2

ABCD

RIDE ON REEL MOWER

USAD004

GP400 DIESEL

GY000301

ABCD

en-5

SAFETY 3

West Road

Ransomes Europark

Ipswich IP3 9TT

England

t R

West Road

Ransomes Europark

Ipswich IP3 9TT

England

A Weight of ROPS

B Date Code

C Standard Used

DPart Number

E Used on Product

F Serial Number

ROPS Serial Plate Location

The ROPS serial plate (C) is located at the base of the front of the ROPS

main beam.

en-6

3 SAFETY

3.3GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _____________________

3.3.1 DURING SERVICE LIFE __________

Used oil, oil filters and engine coolant are hazardous materials. Recommended procedures must be followed for

their safe removal.

If a fluid leaks, contain the spill to make sure that the leak does not flow into the ground or drainage system.

Follow the local laws to make sure that leaks are controlled safely.

The maintenance procedures in this manual make sure that the damage that the machine can cause in the local

environment is controlled safely.

When the machine completes its full service life, the following actions must be taken.

3.3.2 END OF SERVICE LIFE

These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the ap-

proved local waste disposal and agencies for recycled materials.

• Park the machine in a location to use all of the necessary lifting equipment.

• Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical

manuals applicable to the machine.

• Remove and store correctly

1. Batteries

2. Fuel

3. Engine coolant

4. Oils

• Disassemble the structure of the machine and refer to the technical manuals where applicable. Give

attention to parts that have mechanical pressure or tension applied to the part in the machine, including

springs.

• Items that continue to have a service life must be separated and returned to the local store.

• Items that are worn must be separated into the material groups and removed according to the agencies

for recycled materials that are available. Common types are as follows:

• Steel

• Non ferrous metals

• Aluminium

• Brass

• Copper

• Plastic materials

• Identified

• Can be recycled

• Can not be recycled

• Not identified

• Rubber

• Electrical and Electronic Components

• If an item is not easily separated into different material groups, the material must be added to the

“General discarded materials” area.

• Do not burn discarded materials.

Change the machinery records to show that the machine is not in service and is discarded. Supply this serial

number to Ransomes Jacobsen Warranty Department to close their records.

en-7

SAFETY 3

3.4 PARTS MANUAL ______________________________________________________

In compliance with the ISO14001 standard, Ransomes Jacobsen Limited does not send a paper parts manual

with every product.

To refer to a parts list for this mower you have four options:

1. Website – www.Ransomes Jacobsen.com. Select the “CUSTOMER CARE” tab.You now have access

to Parts drawings and lists to help with the identification of spare parts.

2. Website – www.Ransomes Jacobsen.com. Select the “SUPPORT” tab.You now have access to a PDF

version of the parts manual.

3. Complete the form included in the technical manual pack supplied with the machine for one of the two

options below

a. A disc that contains an electronic copy of the Parts Book.

b. A paper copy of the parts manual.

en-8

3 SAFETY

3.5 KEY NUMBERS _______________________________________________________

Record the key numbers shown below:

Starter Switch:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Diesel tank:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Record the machine and engine numbers shown below:

The machine serial number is found on the registration plate and the engine serial number can be found on the

rocker cover.

Machine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Engine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

en-9

SAFETY 3

3.1 HOW TO OPERATE SAFELY_____________________________________________

3.1.1 Safe Operation

a Read the Operator’s Manual and other training material. If the operator or technician can not read this

manual, the owner is responsible to describe this material to the operators and technicians. Manuals in

additional languages may be available on the Jacobsen or RansomesJacobsen website.

a Read all of the instructions for this mower carefully. Know the controls and the correct operation of the

equipment.

b Children or persons who do not understand these instructions must not use the mower. The local

regulations can limit the age of the operator.

c Never use a mower near persons, including children or animals.

d Remember that the operator or owner is responsible for accidents or hazards that occur to other persons or

their property.

e Never carry passengers.

f Never allow persons to operate or service the mower or its attachments without correct instructions.

g Do not operate equipment while tired, sick or after you use alcohol or drugs.

3.1.2 Preparation

a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard

hat, safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving

parts.

b Do not operate the equipment with the Interlock System disconnected or the system does not operate

correctly. Do not disconnect or prevent the operation of any switch.

c Never operate equipment that is not in correct order or without decals, guards, shields, deflectors or other

protective devices fastened. When you mow with a side discharge deck, DO NOT operate the cutting unit

without the discharge chute installed.

d Inspect the mower before you operate the mower. Check the tire pressure, engine oil level, the radiator

coolant level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the

mower.

e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during

bad weather. Never operate the mower with lightning in the area.

f Inspect the area to select the accessories and attachments that are needed to correctly and safely do the

job. Only use parts, accessories and attachments approved by Jacobsen.

g Be careful of holes in the terrain and other hazards that are not visible.

h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be

careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles

(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.

i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you

rotate one blade, other blades can rotate.

WARNING

EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.

Know the location and correct operation of controls. Operators without experience must receive instruction from

another person that knows the correct operation of the equipment before you operate the mower.

Only use parts, accessories and attachments approved by Jacobsen.

en-10

3 SAFETY

3.1.3 Operation

a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the

exhaust fumes can increase to dangerous levels.

b Never carry passengers. Keep other persons or animals away from the mower.

c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with

the operator in the seat. Never start the engine with persons near the mower.

d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep

your hands and feet away from the cutting units.

e Do not use on the slopes greater than the safe slope limit for the equipment.

f To guard against over turning or loss of control:

– Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).

– Do not start or stop suddenly on slopes.

– Decrease the speed when you operate on slopes or when you must turn. Use caution when you change

direction. Turf condition can change the mower stability.

– Use caution when you operate the mower near drop-offs, ditches or embankments.

– Be careful of holes in the terrain and other hazards that are not visible.

g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not

operate the cutting units when you drive in the reverse direction.

h Use caution when you go near corners, trees or other objects that can prevent a clear view.

i Equipment must meet the current regulations to be driven on the public roads.

j Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and

travel at decreased speed. Look for traffic.

k Stop the blades when the mower is on any surface that is not grass.

l Do not release the cut grass in the direction of persons or allow persons near the mower while in operation.

m Do not operate the mower with damaged guards or without safety devices in position.

n Do not change the engine governor setting or over-speed the engine. Never change or tamper with

adjusters that are closed with a seal for the engine speed control.

o Before you leave the operator compartment, for any reason:

– Disengage all the drives and lower attachments to the ground.

– Engage the parking brake.

– Stop the engine and remove the key.

p When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for

damage and make repairs.

q Decrease the throttle setting before you stop the engine.

r Do not use this equipment for uses that the mower was not made for.

en-11

SAFETY 3

3.1.4 ROPS

a The ROPS is a safety device. Keep the ROPS in the vertical and locked position. Always use the seat belt

when you operate the mower. Make sure the seat belt can be released quickly in an emergency.

b Only operate the mower with the ROPS in the folded position on flat and level surfaces when necessary.

Do not operate the mower with the ROPS in the folded position on slopes, near sharp edges or near water.

There is no roll over protection with the ROPS in the folded position.

c Check for clearance before you drive below objects. Do not contact tree branches, electrical wires or other

objects with the ROPS.

d Do not use the seat belt with the ROPS in the folded position.

e Inspect the ROPS for damage. Keep the ROPS hardware fastened.

f Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged

ROPS.

g Do not remove the ROPS from the mower.

h Jacobsen must approve any changes to the ROPS.

3.1.5 Safe Handling of Fuels

a The fuel and the fuel vapors are flammable. Use caution when you add the fuel to the mower. The fuel

vapors can cause an explosion.

b Never use the containers that are not approved to keep or transfer fuel.

c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of

fuel or fuel vapors.

d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel

container on the ground away from your vehicle before you fill the container.

e Refuel the mower before you start the engine. When the engine is in operation or while the engine is hot,

never remove the fuel cap or add fuel to the mower.

f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.

g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to

lock the fuel nozzle in the open position.

h Do not over fill the fuel tank. Leave at least 1 inch (25 mm) below the filler neck.

i Always tighten the fuel tank cap and container cap after you add fuel.

j If the fuel spills on your clothing, change your clothing immediately.

3.1.6 Maintenance and Storage

a Before you clean, adjust or repair this equipment, push PTO switch to the OFF position, lower the cutting

unit to the ground, engage the parking brake, stop the engine and remove the key.

b Make sure the mower is parked on a solid and level surface.

c Never work on a mower that is lifted only by the jack. Always use the jack stands.

d Never allow persons to service the mower or its attachments without correct instructions.

e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a

positive mechanical lock is used.

When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near

flames or drain the fuel inside a building.

f Disconnect the battery before you service the mower. Always disconnect the negative battery cable before

the positive battery cable. Always connect the positive battery cable before the negative battery cable.

en-12

3 SAFETY

g Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To

prevent an explosion, keep any device that can cause sparks or flames away from the battery.

h Disconnect the battery charger from the power supply before you connect or disconnect the battery charger

to the battery. Wear protective clothing and use insulated tools when you service the battery.

i Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged

blades, do not try to correct a damaged blade.

j Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in

operation, unless the adjustment needs the engine in operation.

k Carefully release the pressure from components with stored energy.

l To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the paper

or cardboard to find leaks.

m The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your

skin, a doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.

n When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to

the correct torque. Make sure the hydraulic system is in good condition before you start the engine.

o Keep the mower and the engine clean.

p Allow the engine to become cool before storage and always remove the ignition key.

q Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.

r Replace worn or damaged parts for safety. Replace damaged or worn decals. Only use parts, accessories

and attachments approved by Jacobsen.

s To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank

area.

t Disconnect the battery and controller connectors before you weld on this mower.

3.1.7 When you Put the mower on a trailer

a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can

carry the weight of the mower.

b Use a full-width ramp to load or unload the mower on a trailer.

c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be

sent down and toward sides of trailer.

Make sure that all latches are correctly fastened.

en-13

SAFETY 3

3.1.8 Important Safety Notes

This safety alert symbol is used to alert you to possible hazards.

DANGER:

Indicates a dangerous condition that WILL cause death or injury unless it is prevented.

WARNING:

Indicates a dangerous condition that CAN cause death or injury unless it is prevented.

CAUTION:

Indicates a dangerous condition that can cause injury and property damage unless it is prevented. Also, the label

can indicate work procedures that are not safe.

IMPORTANT:

Only drive the machine at road speed when you are on a highway. You must not select road speed on grass

areas or rough roads and gravel tracks.

Some illustrations in this manual can show shields, guards or plates removed for clearness. This equipment must

not be operated without these devices correctly fastened in position.

By following all instructions in this manual, you increase the life of your machine and keep its maximum

performance. Adjustments and maintenance must always be done by an approved technician.

If additional information or service is needed. Contact your Authorized Ransomes Jacobsen Dealer, who knows

the latest methods to service this equipment and can give that service.

WARNING

The Interlock System on this mower prevents the starting of the mower unless a.) The parking brake is

Engaged. b.) The mow switch is in the OFF position, c.) The traction pedal is in the Neutral position. d) The

operator is in the seat. The system stops the engine when the operator leaves the seat a.) without the parking

brake engaged or b.) the mow switch is not in the OFF position. NEVER operate the mower unless the

Interlock System is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction pedal to the Neutral position.

b. Disengage all drives.

c. Lower all implements to the ground.

d. Engage parking brake.

e. Stop the engine and remove the ignition key.

2. Keep your hands, feet, and clothing away from moving parts. Wait for all movement to stop before you

clean, adjust, or service the machine.

3. Keep the area of operation clear of all persons and animals.

4. Never carry any passengers.

5. Never operate the equipment without a correctly fastened grass deflector in position.

en-14

3 SAFETY

WARNING

California Proposition 65

Engine Exhaust, Some Of Its Constituents, And Some Vehicle Components Contain Or Release Chemicals

Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.

WARNING

To Prevent Injury From The Hot Oil At High Pressure, Do Not Use Your Hands To Check For Oil Leaks. Make

Sure That You Use Paper Or Cardboard.

Release Of Hydraulic Fluid At High Pressure Has Enough Force To Enter Through The Skin. If The Fluid Enters

Through The Skin, The Fluid Must Be Surgically Removed Within Hours By A Specialist Doctor Or Gangrene

May Result.

WARNING

When The Machine Is Driven Off-Road, A Seat Belt Must Be Worn Only When A Rops Frame Is In Position.

This Warning Is Because A Seat Belt Must Be Worn With A Rops To Follow The Machinery Directive,

2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover. (ANSI B71.4-2012 section 20.7)

Ransomes Jacobsen Limited Recommends That The Owner/User Of The Machine Completes A Local Risk

Assessment Of The Machine To Find Any Conditions That Do Not Follow This Rule. E.g. When You Drive The

Machine Next To Water Or On The Highway.

WARNING

Explosive Gases Are Released By Batteries. The Battery Contains Corrosive Acid And Supply An Electrical

Current That Is High Enough To Cause Burn Injuries To The Body.

WARNING

You Must Not Use This Machine To Tow Other Vehicles.

WARNING

Ear Protection Must Be Worn When You Operate Machines With

An Operator Ear Noise Level Of More Than 85 db(A) Leq.

en-15

SAFETY 3

WARNING

Vibration Exposure Limits

Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the

Daily Exposure Time (Trigger Time). E.g. A product with 5m/s² vibration can be used up to 2 hours/day to

reach the EAV and up to 8 hours/day to reach the ELV.

Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²

Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no action need be

taken

Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²

If several tools are use the exposure values must be combined:

Total exposure is then the combined value of the activities

WARNING

Never Mow If There Is A Risk Of Lightning Or You Hear Thunder. If You Are In The Middle Of Mowing,

Stop In A Safe Place, Turn Off The Engine And Go Inside a Building.

CAUTION

When You Do Any Welding On The Machine, The Battery, Controller And Display Must Be Disconnected

Before You Start. You Must Not Open The Controller. If The Controller Is Opened, This Can Cancel All Of The

Warranties And Can Cause The Failure Of The Machine.

CAUTION

Personal Protective Equipment (PPE), For Example Safety Glasses, Leather Work Shoes Or Boots, A Hard

Hat, Leather Work Gloves And Ear Protection Must Be Used After The Owner/User Completes A Local Risk

Assessment Of The Mower, To Prevent Injury.

Training In All Manual Operations Must Be Given By An Approved Person Before The Machine Is Used The

First Time.

en-16

4 SPECIFICATIONS

4.1 ENGINE SPECIFICATION ______________________________________________

Kubota

Model D722-E3B D722-E4B

Type Vertical, water-cooled, 4-cycle diesel engine.

Number of Cylinders 3

Bore & Stroke 67mm x 68mm (2.64 x 2.68)

Total Displacement 719cm³

Combustion Chamber Spherical type (E-TVCS) Spherical type (E-TVCS,NA)

Gross Intermittent Power 13.2kW (17.7hp) @ 3200rpm

Maximum Speed: 3400 ± 50 RPM (No load) 3500 ± 50 RPM (No load)

Idle Speed: 1700 ± 100 RPM 1800 ± 50 RPM

Order of Firing 1-2-3

Direction of Rotation Counter-clockwise (viewed from flywheel side)

Injection Pump Bosch MD type mini pump

Injection Pressure 13.73 MPa (140kgf/cm²)

Injection Timing (Before T.D.C.) 21° 20°

Compression Ratio 23:1 23.5:1

Fuel: No. 2-D Diesel fuel (ASTM D975)

Lubrication (API Classification) Above CF grade

Oil Sump Capacity: 3.2 litres (0.85 gallon US)

Dimensions (length x width x height) 435.1mm x 404mm x 564.1mm (17.12 x 15.90 x 22.20)

Dry Weight 63.1kg

Starting System Cell starter (with glow plug)

Starting Motor 12V, 0.8 kW 12V, 1.0kW

Charging Generator 12V, 450w 12V, 40A

Briggs & Stratton

Model Vanguard 350447

Type V Twin type 1294, 4 stroke air cooled

Number of Cylinders: 2

Gross Intermittent Power: 13.2kW (17.7hp) @ 3400rpm

Total Displacement: 574 cm³

Maximum Speed: 3400 RPM (No load)

Idle Speed: 1700 ± 100 RPM

Oil sump capacity: 1.4 litres (0.37 gallon US)

Fuel: Unleaded gasoline minimum 87 octane

en-17

SPECIFICATIONS 4

4.2 DIMENSIONS & WEIGHTS ________________________________________________

A Width of Cut: 160 cm 63 inches

B Overall Width Cutting: 188 cm 74 inches

Overall Width Transport (minimum): 186 cm 73.25 inches

C Overall Height with ROPS Frame: 196.5 cm 77.38 inches

D Overall Length Without Grass Boxes: 219 cm 86.2 inches

E Overall Length With Grass Boxes: 250 cm 98.4 inches

F Wheel Track: 121.7 cm 48 inches

G Wheel Base 2 Wheel Drive: 133.2 cm 52.44 inches

G Wheel Base 3 Wheel Drive: 125.5 cm 49.5 inches

H Turning Circle 2 Wheel Drive: 368 cm 144.88 inches

H Turning Circle 3 Wheel Drive: 393.8 cm 155 inches

Weight of Diesel Machine, No Fuel, Plus ROPS: 630.5 kg 1390 lbs

Weight of Gasoline Machine, No Fuel, Plus ROPS: 560.5 kg 1236 lbs

Weight of one Cutting Unit 11 Knife 31.6 kg 69.6 lbs

Weight of one Brush & Groomer Kit: 7 kg 15.4 lbs

Weight Diesel Fuel 54l (14.25 US Gallons) 46 kg 101 lb

Weight of Gasoline Fuel 54 litres (14.25 US Gallons) 40 kg 87 lb

en-18

4 SPECIFICATIONS

4.3 MACHINE SPECIFICATION_____________________________________________

Frame construction:Welded tubular steel chassis.

Cutting unit drive:Direct Drive hydrostatic reel drive pump, bi-directional hydraulic gear motor with reel control

and Backlap valves.

Transmission:Variable displacement hydrostatic pump with low speed high torque wheel motors

Speeds:

Cutting:0 - 6 km/h ( 0 - 3.7 mph ) Forward

0 - 3 km/h ( 0 - 1.9 mph ) Reverse

Transport: 0 - 12 km/h ( 0 - 7.5 mph ) Forward

0 - 3 km/h ( 0 - 1.9 mph ) Reverse

Steering:Hydrostatic power steering 2.5 turns lock to lock, with 330mm (13 inches) dia steering wheel.

Ground pressure:1 kg/cm² (14 psi) (Dependent on tyre pressures and accessories fitted)

Brakes: Hydrostatic braking with 152mm (6 inches) Caliper disc parking brakes on front wheels.

Battery: Exide 093 (SAE 500) 12volt

TYRE PRESSURE

Product

Front Wheel Rear Wheel

Tyre Size Tyre Type Tyre Pressure Tyre Size Tyre Type Tyre Pressure

GP400 20 x 10.00 - 10 OTR Smooth

0.7 bar

(10 psi)

20 x 10.00 - 10 OTR Smooth

0.7 bar

(10 psi)

en-19

SPECIFICATIONS 4

4.4 VIBRATION LEVEL ___________________________________________________

The machine was tested for hand/arm vibration levels. The operator was in the normal position to drive the

vehicle, with two hands on the steering mechanism. The engine was in operation and the cutting device was in

rotation, while the machine was not moving.

The Machinery Safety Directive 2006/42/EC

By compliance to:

The Lawnmower Standard BS EN ISO 5395

Referenced to Hand/Arm: BS EN ISO20643:2008

Information Supplied for Physical Agents Directive 2002/44/EC

By reference to:

Hand/Arm Standards: BS EN ISO 5349-1 (2001)

BS EN ISO 5349-2 (2002)

The machine was tested for Whole Body vibration levels. The operator was in the normal position to drive the

vehicle, with two hands on the steering mechanism. The cutting device was in rotation with the machine driven in

a straight line at 6 Km/hr on a level and cut lawn.

The Machinery Safety Directive 2006/42/EC

By compliance to:

Whole Body EN1032:2003

Information Supplied for Physical Agents Directive 2002/44/EC

By reference to:

Whole Body Standards BS EN ISO 2631-1 (1997)

measurements according to the requirements of BS EN ISO 5395

GP400 Diesel

Hand / Arm

Acceleration

Level

Series GY with ROPS

Max. LH or RH Accelerations m/s²

Mean Value of X, Y, Z Aeq

0.77 ± 0.40

GP400 Gas

Hand / Arm

Acceleration

Level

Series GZ with ROPS

Max. LH or RH Accelerations m/s²

Mean Value of X, Y, Z Aeq

0.42 ± 0.40

GP400 Diesel

Whole Body

Acceleration

Level

Series GY with ROPS

Max. Seat Accelerations m/s²

Mean Value of X, Y, Z Aeq

0.43 ± 1.57

GP400 Gas

Whole Body

Acceleration

Level

Series GZ with ROPS

Max. Seat Accelerations m/s²

Mean Value of X, Y, Z Aeq

0.72 ± 1.57

en-20

4 SPECIFICATIONS

4.5 NOISE LEVEL________________________________________________________

The Machinery Safety Directive 2006/42/EC

And

Exposure Of Workers To The Risks Arising From Physical Agents (Noise) Directive 2003/10/EC

By compliance to:

The Lawnmower Standard BS EN ISO 5395:2013

And

Sound Pressure Standard EN ISO 3746: 2010

GP400 Gas Measured Sound Pressure 82 dB(A) ± 0.86 LWA

GP400 Diesel Measured Sound Pressure 86 dB(A) ± 0.86 LWA

When the machine was tested for sound power (Noise in the Environment).

The Machinery Safety Directive 2006/42/EC

And

Noise Emission In The Environment By Equipment For Use Outdoors

Directive 2000/14/EC

By compliance to:

Sound Power Standard EN ISO 3744:2010

GP400 Gas Measured Sound Power 101 dB(A) ± 0.86 LWA

GP400 Diesel Measured Sound Power 101 dB(A) ± 0.86 LWA

4.6 SLOPES ____________________________________________________________

DO NOT USE ON SLOPES GREATER THAN 16°. The 16° slope was calculated using static stability

measurements according to the requirements of BS EN ISO 5395-2013

Pagina se încarcă ...

Ransomes USAG004 / USAD004 / 62706 Manualul proprietarului

Marca: Ransomes

Model: USAG004 / USAD004 / 62706

Categorie: Cositoare

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ransomes USAG004 / USAD004 / 62706 Owner's manual

Ransomes USAG004 / USAD004 / 62706 Manualul proprietarului

Acest manual este potrivit și pentru

Ransomes USAG004 / USAD004 / 62706 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente