Smithco 7576 Tournament Ultra Lite Roller Manualul proprietarului

TOURNAMENT ULTRA

LITE CE

7576

SN: T8083

Revised December 2018

Product Support: 1020 Hawaii Rd; Humboldt, KS 66748

1-888-422-5173 [email protected]

Wayne, PA 19087 www.smithco.com

Parts Manual

TABLE OF CONTENTS

TITLE PAGE

Frame Drawing 1

Frame Parts List 2

Roller Housing Drawing 3

Roller Housing Parts List 4

Steering Drawing 5

Steering Parts List 6

Engine Drawing & Parts List 7

Wiring Drawing & Parts List 8

Hydraulic Plumbing Drawing 9

Hydraulic Plumbing Parts List 10

750-847 Pump Drawing 11

750-847 Pump Parts List 12

Pump Linkage Drawing 13

Pump Linkage Parts List 14

Performance Chart 15-16

7520 Trailer Drawing 17

7520 Trailer Parts List 18

Guide Rail & Roller Stop Installation 19

7525 Trailer Drawing f/7000 20

7525 Trailer Parts List f/7000 21

CE 22-24

SMITHCO Warranty 25-26

7576 FRAME DRAWING

1

7576 FRAME PARTS LIST

REF# PART# DESCRIPTION QTY.

1 832-123-2 Low-Back “Smithco” Seat Assembly 1

2 750-913 Engine Cover 1

3 750-917 Engine Cover Hold Down 4 7/8” 2

4 750-891 Gas Shock Assembly w/Ball Stud 1

5 750-911 Seat Hinge 1

6 750-916 Oil Tank 1

7 750-908 Deck Plate 1

8 720-078-1 5/16” x 1” Clevis Pin 2

9 720-079 Cotter Pin 3/32” x ¾” 2

10 11-101-1 ¼” Fine Thread Yoke 2

11 750-915 Left Foot Pedal Rod 1

12 750-914 Right Foot Pedal Rod 1

14 750-912 Foot Pedal 2

15 10-007 Bushing 4

16 750-906 Main Frame 1

17 750-192 1 1/8” Poly Hex Nut & Cap 2

18 932-042 Thick Slotted Hex Nut 1 ¼” – 12 2

19 709-143-1 1/8” x 2 ½” Cotter Pin 2

20 932-023 Bearing 4

21 932-024 Spacer 2

22 932-022 Seal 4

23 400-061 ½” x 3 1/2” Bolt 1

24 750-186 Spacer ½” ID x ¾” OD x ½” 2

25 750-907 Swivel Axle Bracket 1

26 750-118-1 Oil Tank Cap 1

27 400-112 ½” Lock Nut 1

28 400-008 5/16” x 2 ½” Bolt 2

29 400-109 5/16” Lock Nut 2

30 400-116 3/8” Lock Nut 2

31 400-018 3/8” x 2 ½” Bolt 2

32 44-967 5/16” FT Tie Rod End 2

33 400-002 5/16” x 1” HHCS 2

34 400-281 5/16” Flange Locknut 2

35 750-942 Left Outer Step (CE Only) 1

36 750-943 Right Outer Step (CE Only) 1

37 750-269 Battery Box 1

2

7576 ROLLER HOUSING DRAWING

3

7576 ROLLER HOUSING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-825 Left Roller Housing 1

2 750-826 Right Roller Housing 1

4 40-199 Idler Spring 1

5 1083 #50 Master Link 3

6 750-415 #50 Chain 50 pitch w/3 Connecting Links 1

7 750-821 Roller Cylinder 2

8 400-105 ½” – 13 Hex Nut 5

9 713-806 Ball Joint 2

10 400-056 ½” – 13 X 2 ½” HHCS 2

11 400-136 ½” – 20 Fine Thread Hex Nut 2

12 750-411 Tie Rod 1

13 400-044 ¼” – 20 x 1” Bolt 2

14 400-208 ¼” Lock Washer 2

15 720-004 Flange Bearing 2

16 750-721 Spacer 1 ¼” 2

17 750-220-2 Hub w/Plate, Bushing & Shaft 2

21 750-802 Hub 4 Bolt 2

22 1189 Lug Bolt 8

23 400-210 ½” Lock Washer 8

24 400-105 ½” – 13 Hex Nut 8

25 750-801-3 Castle Nut 2

26 740-023 3/16” x ¾” Key 2

27 750-801 Hydro Gear Motor 2

28 750-827 Bolted End Plate f/Housing 2

29 400-209 3/8” Lock Washer 16

30 400-090 3/8” x 1 ¼” Bolt 16

31 400-103 3/8” Hex Nut 8

32 750-873 Steering Chain Adjuster – Turnbuckle 1

4

7576 STEERING DRAWING

5

7576 STEERING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 730-046-2 Steering Wheel Cap 1

2 932-122 5/8” – 18 Hex Jam Nut 1

3 400-143 5/8” Lock Washer 1

4 730-046 Steering Wheel 1

5 832-028-1 Tilt Steering Mechanism & Boot w/Pin 1

6 740-023 3/16” x ¾” Key 1

7 400-073 ¼” x 1” Self Tap Screw 4

8 400-003 5/16” – 18 x 1 ¼” HHCS 4

9 400-102 5/16” – 18 Hex Nut 8

10 750-286 Upper Steering Shaft 1

11 832-030 7/32” x 1 ¼” Spring Pin 1

12 41-120 U-Joint ¾” x ¾” 1

13 1088 3/16” x 1” Key 3

14 750-266 Steering Sprocket Shaft 1

15 750-909 Steering Column 1

16 400-010 5/16” – 18 x 5” HHCS 2

17 400-207 5/16” Lock Washer 8

18 400-314 5/16” x 4 ¼” Bolt 2

19 41-194 Chain Adjuster Bracket 1

20 1036 Jackshaft Bearing 2

21 1075 #40 Jackshaft Sprocket 11T 1

22 41-251 #40 Chain x 108 Pitch w/Connecting Link 1

23 750-148-1 Sprocket & Bearing Shaft 5 ½” 1

24 750-894 Bearing & Sprocket Bracket 1

25 400-103 3/8” – 16 Hex Nut 4

26 400-209 3/8” Lock Washer 4

27 1040 Front Axle Bearing 1

28 750-234 Steering Sprocket 60T 40BS60 x ¾” 1

29 750-315 ¼” x 2 ½” Spring Pin 2

30 750-133-1 50BS 19 x ¾” Sprocket 1

31 750-722 1” Spacer (3/4” ID) 1

32 400-116 3/8” – 16 Locknut 4

33 400-202 5/16” Flat Washer 4

34 400-015 3/8” – 16 x 1 ½” HHCS 4

35 750-107 Steering Column Cover 1

36 750-195 Steering Shaft Bracket 1

37 520-007 Bronze Bushing 2

38 709-382 ¼” 90° Grease Zert 1

39 1088-1 3/16” x 1 ½” Key 1

6

7576 ENGINE DRAWING

7576 ENGINE PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-935 8 HP Engine (Model# GX240UT2 -QAR2) 1

2 400-090 3/8” x 1 ¼” Bolt 8

3 1517 ¼” x 1” Key 1

4 750-851 Pump Hub 17mm w / #5 Key 1

5 720-027 Element 1

6 41-147 Engine Coupling 1” 1

7 750-201 3/16” x 1” Key 1

8 750-127 Bell Housing 6” 1

9 750-127-1 Bell Housing Cover 1

10 750-847 16cc without Aux Charge Pump 1

11 750-211 Engine Base 1

12 750-927 Engine Spacer 4

7

WIRING DRAWING

WIRING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-935 8 HP Engine (Model# GX240UT2-QAR2) 1

2 750-555-7 PS1230 Battery 1

3 750-555-5 Rectifier 1

4 932-119-1 Safety Seat Switch 1

5 942-049 Wiring Harness f/Seat Switch 1

6 750-555-6 Wiring Harness 1

7 750-555-2 Light Kit Battery Box 1

8

HYDRAULIC PLUMBING DRAWING

9

HYDRAULIC PLUMBING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-916 Oil Tank 1

2 750-825 Left Roller Housing 1

3 750-826 Right Roller Housing 1

4 750-302 Filter Head 1

5 750-801 Wheel Motor 2

6 750-847 16cc without Aug Charge Pump 1

7 750-326 Wheel Motor Fitting 4

8 750-325 Oil Filter Head Fitting 2

9 750-322 Pump Fitting 2

10 750-324 Pump Fitting Top 1

11 750-295 Pump Fitting 1

12 750-920-1 Hyd Hose 57” x ½” (w/o 90° to Straight) 1

13 750-502 Hard Line Clamp 2

14 750-920-2 Hydraulic Hose 14” – Pump to Filter 1

15 750-920-3 Hydraulic Hose 35” 2

16 750-920-4 Hydraulic Hose 11” – Oil Tank to Filter Head 1

17 750-920-5 Hydraulic Hose 7” – Oil Tank to Pump 1

18 750-519 Hard Line Long Left Side 1

19 750-520 Hard Line Short Left Side 1

20 750-506 Hard Line Long Right Side 1

21 750-507 Hard Line Short Right Side 1

22 750-923 Drain Cap 1

23 750-920-6 Drain Hose 1

24 750-920-7 Hydraulic Hose 52” 1

NOTE: OIL FILTER IS A PART# 750-300

COMPLETE HOSE KIT IS A PART# 750-920

10

750-847 PUMP DRAWING

11

750-847 PUMP PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-847-3 Retaining Ring 1

2 750-847-4 Lip Seal 1

3 750-847-5 Spacer 1

4 750-847-6 Shaft Kit 1

5 750-847-7 Housing 1

6 750-847-8 Trunnion Seal Kit 1

7 750-228-15 Pin 2

8 750-847-9 O-Ring 1

9 750-847-10 Charge Relief 1

10 750-847-11 Shock Valve Kit 1

11 750-847-12 End Cap 1

12 750-847-11 Shock Valve Kit 1

13 750-847-13 Plug 1

14 750-228-7 Bypass Kit 1

15 750-847-14 Charge Pump 1

16 750-847-15 Screw 4

17 750-847-13 Plug 1

18 750-847-16 Screw 2

19 750-847-17 Valve Plate 1

20 750-847-18 Cylinder Block 1

21 750-847-19 Thrust Bearing 1

22 750-847-20 Swash Plate 1

23 750-128-38 Slot Guide 1

24 750-847-21 Trunnion Arm 1

25 750-849 Seal Kit 1

12

PUMP LINKAGE DRAWING

13

PUMP LINKAGE PARTS LIST

REF.# PART# DESCRIPTION QTY.

1 750-847 16cc without Aug Charge Pump 1

2 750-228-30 Bushing 1

3 750-343-1 Shift Lever Top (New) 1

3 750-343 Shift Lever Top (Old) 1

4 750-344-1 Shift Lever Bottom w/Bolt (Sq. Hole .470) 1

4 750-344 Shift Lever Bottom (Sq. Hole .350) 1

5 750-228-31 Bushing 1

6 750-345 Shift lever Right (Bent) 1

7 750-229-1 Gold Spring 1

8 750-228-32 Nylon Washer 1

9 750-346 Shift Lever Left (Straight) 1

10 750-228-33 Nylon Washer 1

11 750-228-34 5/16” Flat Washer 2

12 750-228-35 Allen Head Bolt 1

13 750-228-36 Allen Head Bolt 1

14 750-228-37 Pump Bracket Kit 1

14

PERFORMANCE CHART

Product Type

PC

PG

PJ

PR

PW

Displacement

in

3

/rev

[cc/rev]

0.37

[6.1]

0.62

[10.2]

0.73

[12]

0.97

[16]

1.33

[21.8]

Input Speed

Maximum Unloaded

Minimum Loaded

rpm

3600

1800

3600

1800

3600

1800

3600

1800

3600

1800

System Operating Pressure

Continuous

Intermittent

Peak

psi

[bar]

psi

[bar]

psi

[bar]

750

[51]

1750

[120]

2500

[172]

1000

[70]

2100

[145]

3500

[240]

1000

[70]

2100

[145]

3500

[240]

1250

[86]

2500

[172]

3750

[260]

1250

[86]

2500

[172]

3750

[260]

Pump Performance

@ 2400 rpm/1000 psi

@ 3000 rpm/1000 psi

@ 3600 rpm/1000 psi

gpm [l/min]

3.6 [13.6]

4.5 [17.0]

5.4 [20.4]

6.1 [23.1]

7.6 [28.8]

9.2 [34.8]

7.1 [26.8]

8.9 [33.6]

10.8 [40.8]

9.6 [36.3]

12 [45.4]

14.4 [54.5]

13.1 [49.6]

16.4 [62.1]

19.6 [74.2]

Case Pressure

Maximum @ Cold Start

Continuous - Max.

psi [bar]

10 [0.7]

4 [0.3]

10 [0.7]

4 [0.3]

10 [0.7]

4 [0.3]

25 [1.7]

10 [0.7]

25 [1.7]

10 [0.7]

Inlet Vacuum

Maximum Continuous Inches Mercury

4

Charge Pump Displacement(s)

in

3

/rev

[cc/rev]

.13

[2.1]

0.11/0.13

[1.9/2.1]

0.19

[3.2]

0.13/0.19

[2.1/3.2]

0.13/0.19

[2.1/3.2]

Auxiliary Pump Displacement

in

3

/rev

[cc/rev]

0.19

[3.2]

0.19

[3.2]

0.19

[3.2]

0.19

[3.2]

0.19

[3.2]

Auxiliary Pump Relief Setting

psi

[bar]

650

[45]

650

[45]

650

[45]

650

[45]

650

[45]

Auxiliary Pump Performance

@3200 rpm, 500 psi, 70 SUS

[13 Cst] oil, & 180°F

gpm

[l/min]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

Control Torque Required

to Stroke Pump

[Approximate - 20° External Stroke Angle]

75

85

95

105

15

lb-in / 1000 psi

[N-m / 70 bar]

lb-in / 500 psi

[N-m / 35 bar]

[8.5]

55

[6.2]

[9.6]

60

[6.8]

[9.6]

60

[6.8]

[10.7]

75

[8.5]

[11.9]

85

[9.6]

Pump Oil Temperature

Maximum Intermittent (hottest point)

Normal Operating Range

°F

[°C]

°F

[°C]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

Fluid Viscosity Limits @ 230°F [110°C]

Optimum

Minimum

SUS[cSt]

70 [13]

55 [9]

70 [13]

55 [9]

70 [13]

55 [9]

70 [13]

55 [9]

70 [13]

55 [9]

Weight of Unit

lbs [kg]

7 [3.2]

8 [3.6]

12.65 [5.7]

12 [5.4]

14 [6.3]

Inlet Filtration Requirement

Nominal

micron

25

16

7520 TRAILER DRAWING

17

7520 TRAILER PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-430 Trailer Bed 1

2 750-432 Right Side Ramp 1

3 750-431 Left Side Ramp 1

4 750-433 Ramp Plate 1

5 400-321 ¼” X ¾” X 20 Truss Head Bolt 8

6 400-342 ¼” Flanged Locknut 8

7 750-422 3/64 x 6 Lanyard 2

8 750-421 Snap Pin 3/16 x 1 ¼” 2

9 750-437 Ramp Latch 2

10 400-112 ½” – 13 Locknut 2

11 400-027 ½” – 13 x 1 ½” HHCS 2

12 750-164-7 Rubber Matting f/7520 Ramp 55” x 7” 4

13 750-438 Rubber Matting f/Bed 47” x 7” 2

14 400-255 Elevator Bolt 12

15 750-961-1 Jack Pin 1

16 400-281 5/16” Flanged Locknut 12

17 750-434 Drawbar 1

18 750-435 Drawbar Hitch 1

19 400-061 ½” – 13 x 3 ½” HHCS 4

20 400-112 ½” – 13 Locknut 4

21 40-168 Cotter Pin 1/8 x 1” 4

22 750-436 Ramp Pin 2

23 750-960 Axle 1

24 400-015 3/8” – 16 x 1 ½” HHCS 4

25 400-116 3/8” Locknut 4

26 2027-1 Hub Only 2

27 1187 Lug Nut 8

28 2028-1 Bearing 4

29 709-126 Spindle Nut 2

30 2024 Dust Cap 2

31 720-043 Cotter Pin 2

32 750-967 Wheel & Tire 2

33 750-967-1 Tire 2

34 2026 Wheel 2

35 750-961 Jackstand 1

36 750-435-1 Ball Hitch 1

37 750-440 Roller Stop 1

38 400-202 5/16” Flat Washer 8

39 400-014 3/8” – 16 x 1” HHCS 2

40 400-202 5/16” Flat Washer 12

41 400-116 3/8” Locknut 2

42 750-444 Spring 8

43 750-976 Left Guide 1

44 750-975 Right Guide 1

45 750-406-1 Roller Stop 1

18

Pagina se încarcă ...

Smithco 7576 Tournament Ultra Lite Roller Manualul proprietarului

Smithco 7576 Tournament Ultra Lite Roller Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente