Jacobsen 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868 Instruction Sheet

Marca: Jacobsen

Model: 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868

Tip: Instruction Sheet

Instruction Sheet

WARNING

Warning: If incorrectly used, this machine can

cause severe injury. Those who use and maintain

this machine should be trained in its proper use,

warned of its dangers, and must read the entire

manual before attempting to set up, operate, adjust,

or service the machine.

18 Inch TrueSet

™

Reels

62857 – 18 in. Left Hand 11 Blade Greens Reel

62858 – 18 in. Left Hand 15 Blade Greens Reel

62298 – 18 in. Left Hand 8 Blade Fairway Reel

62859 – 18 in. Right Hand 8 Blade Fairway Reel

62299 – 18 in. Left Hand 11 Blade Fairway Reel

62860 – 18 in. Right Hand 11 Blade Fairway Reel

22 Inch TrueSet

™

Reels

62861 – 22 in. Left Hand 7 Blade Reel

62862 – 22 in. Right Hand 7 Blade Reel

62863 – 22 in. Left Hand 9 Blade Reel

62864 – 22 in. Right Hand 9 Blade Reel

62865 – 22 in. Left Hand 11 Blade Reel

62866 – 22 in. Right Hand 11 Blade Reel

62867 – 22 in. Left Hand 15 Blade Reel

62868 – 22 in. Right Hand 15 Blade Reel

Reel Mounting Kits (Single Reel)

4395138 – 18 in. Hydraulic Drive Reel

4395139 – 18 in. Electric Drive Reel

4395140 – 22 in. Hydraulic Drive Fairway Reel

4395141 – 22 in. Electric Drive Fairway Reel

4395142 – 22 in. Hydraulic Drive Greens Reel

4395143 – 22 in. Electric Drive Greens Reel

4387946-Rev A

This manual contains adjustment, maintenance,

troubleshooting instructions, and parts list for your new

Jacobsen reel. This manual should be stored with the

mower for reference during operation.

Before you operate your mower, you and each operator

you employ should read the manual carefully in its

entirety. By following the safety, operating, and

maintenance instructions, you will prolong the life of your

mower and maintain its maximum efficiency.

If additional information is needed, contact your

Jacobsen Dealer.

The serial plate is attached to the reel frame. Jacobsen

recommends you record these numbers below for easy

reference.

CHARLOTTE, NC PRODUCT OF U.S.A.

A Textron Company

Proposition 65 Warning

This product contains or emits

chemicals known to the State of

California to cause cancer and birth

defects or other reproductive harm.

FOREWORD

Suggested Stocking Guide

To keep your mower fully operational and productive, Jacobsen suggests you maintain a stock of the more commonly

used maintenance items. We have included part numbers for additional support materials and training aids.

To order any of the following material:

1. Write your full name and complete address on your

order form.

2. Explain where and how to make shipment:

❑

UPS ❑ Regular

Mail

❑

vernight ❑

d Day

3. Order by the quantity desired, the part number, and

the description of the part.

4. Send or bring the order to your authorized Jacobsen

Dealer.

Service Parts

Service Support Material

Qty. Part No. Description Qty. Part No. Description

4252470 Bedknife Screw (100 Pack)

400074 Hair Pin, 5/64 x 1/4 x 1-3/16”

Qty. Part No. Description

4269792 5 in. Reel Technical Repair Manual

Litho in U.S.A. 9-2017

or portions thereof in any form.”

These are the original instructions verified by

Jacobsen, A Textron Company.

Table of Contents

1 Safety

1.1 Operating Safety............................................... 4

1.2 Important Safety Notes ..................................... 5

2 Specifications

2.1 Product Identification ........................................ 6

2.2 Cutting Units ..................................................... 6

2.3 Accessories & Support Literature ..................... 6

2.4 Declaration of Incorporation ............................. 8

3Setup

3.1 General information ........................................ 10

3.2 Reel Accessories ............................................ 10

3.3 Reel to Mower Assembly ................................ 10

3.4 Electric Reel Motor ......................................... 11

3.5 Hydraulic Reel Motor ...................................... 11

3.6 Reel Stop (Greens Reel) ................................ 11

3.7 Down Pressure (Fairway Reel) ....................... 12

3.8 Counterweight ................................................ 12

4 Adjustments

4.1 General........................................................... 13

4.2 Bedknife-To-Reel ............................................ 13

4.3 Bedknife Adjustment ....................................... 14

4.4 Cutting Height ................................................. 14

4.5 Reel Bearing ................................................... 15

4.6 Bedknife Adjuster Spring ................................ 15

4.7 Bedknife Adjuster Tension .............................. 15

4.8 Grinding Bedknife ........................................... 16

4.9 Down Pressure Spring .................................... 16

4.10 Torque Specification ....................................... 17

6.1 Outer Reel ...................................................... 18

7.1 Inner Reel ....................................................... 20

6.1 Mounting Kits .................................................. 22

1 SAFETY

1.1 OPERATING SAFETY ______________________________________________________

1. Safety is dependent upon the awareness, concern

and prudence of those who operate or service the

equipment. Never allow minors to operate any

equipment.

2. It is your responsibility to read this manual and all

publications associated with this equipment (Safety &

Operation Manual, Engine Manual, and attachments/

accessories instruction sheets). If the operator

cannot read English it is the owner’s responsibility to

explain the material contained in this manual to them.

3. Learn the proper use of the machine, the location

and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar

equipment can lead to accidents.

4. Never allow anyone to operate or service the

machine or its attachments without proper training

and instructions; or while under the influence of

alcohol or drugs.

5. Wear all the necessary protective clothing and

personal safety devices to protect your head, eyes,

ears, hands, and feet. Operate the machine only in

daylight or in good artificial light.

6. Evaluate the terrain to determine what accessories

and attachments are needed to properly and safely

perform the job. Only use accessories and

attachments approved by Jacobsen.

7. Stay alert for holes in the terrain and other hidden

hazards.

8. Inspect the area where the equipment will be used.

Pick up all the debris you can find before operating.

Beware of overhead obstructions (low tree limbs,

electrical wires, etc.) and also underground obstacles

(sprinklers, pipes, tree roots, etc.). Enter a new area

cautiously. Stay alert for hidden hazards.

9. Never direct discharge of material toward bystanders,

nor allow anyone near the machine while in

operation. The owner/operator can prevent and is

responsible for injuries inflicted to themselves, to

bystanders, and damage to property.

10. Do not carry passengers. Keep bystanders and pets

a safe distance away.

11. Never operate equipment that is not in perfect

working order or is without decals, guards, shields,

discharge deflectors, or other protective devices

securely fastened in place.

12. Never disconnect or bypass any switch.

13. Do not change the engine governor setting or

overspeed the engine.

14. Carbon monoxide in the exhaust fumes can be fatal

when inhaled. Never operate the engine without

proper ventilation or in an enclosed area.

15. Fuel is highly flammable; handle with care.

16. Keep the engine clean. Allow the engine to cool

before storing and always remove the ignition key.

17. Disengage all drives and engage parking brake

before starting the engine (motor). Start the engine

only when sitting in operator’s seat, never while

standing beside the unit.

18. Equipment must comply with the latest federal, state,

and local requirements when driven or transported

on public roads. Watch out for traffic when crossing

or operating on or near roads.

19. Local regulations may restrict the age of the operator.

20. Never use your hands to search for oil leaks.

Hydraulic fluid under pressure can penetrate the skin

and cause serious injury.

21. Operate the machine up and down the face of slopes

(vertically), not across the face (horizontally).

22. To prevent tipping or loss of control, do not start or

stop suddenly on slopes. Reduce speed when

making sharp turns. Use caution when changing

directions.

23. Always use the seat belt when operating mowers

equipped with a Roll Over Protective Structure

(ROPS).

Never use a seat belt when operating mowers

without a ROPS.

24. Always disconnect battery cables from battery before

performing any welding operation on the mower.

This machine is to be operated and maintained as specified in this manual and is intended for the professional

maintenance of specialized turf grasses. It is not intended for use on rough terrain or long grasses.

WARNING

EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS.

Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive

instruction from someone familiar with the equipment before being allowed to operate the machine.

SAFETY 1

1.2 IMPORTANT SAFETY NOTES ________________________________________________

This safety alert symbol is used to alert you to potential hazards.

DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious

injury.

CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury

and property damage. It may also be used to alert against unsafe practices.

NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may

also be used to alert against unsafe practices.

For pictorial clarity, some illustrations in this manual may show shields, guards or plates open, or removed. Under no

circumstances should this equipment be operated without these devices securely fastened in place.

By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum

efficiency. Adjustments and maintenance should always be performed by a qualified technician.

If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the

latest methods to service this equipment and can provide prompt and efficient service.

WARNING

The Interlock System on this mower prevents the mower from starting unless

the parking brake is engaged, reel levers are off, and traction lever is in

Neutral. The system will stop the engine if the operator leaves the seat

without engaging the parking brake, setting the reel levers to off, and placing

traction lever in Neutral.

NEVER operate mower unless the Interlock System is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction lever to Neutral.

b. Disengage all drives.

c. Lower all implements to the ground.

d. Engage parking brake.

e. Stop engine and remove the ignition key.

2. Keep hands, feet, and clothing away from moving parts. Wait for all

movement to stop before you clean, adjust, or service the machine.

3. Keep the area of operation clear of all bystanders and pets.

4. Never carry passengers.

2 SPECIFICATIONS

2.1 PRODUCT IDENTIFICATION_________________________________________________

62857.............................. Left Hand 18 in. (457 mm), 11

Blade Reel, without rollers.

62858.............................. Right Hand 18 in. (457 mm), 15

Blade Reel, without rollers.

62298.............................. Left Hand 18 in. (457 mm), 8

Blade Reel, without rollers.

62859.............................. Right Hand 18 in. (457 mm), 8

Blade Reel, without rollers.

62299.............................. Left Hand 18 in. (457 mm), 11

Blade Reel, without rollers.

62860.............................. Right Hand 18 in. (457 mm), 11

Blade Reel, without rollers.

62861.............................. Left Hand 22 in. (559 mm), 7

Blade Reel, without rollers.

62862.............................. Right Hand 22 in. (559 mm), 7

Blade Reel, without rollers.

62863.............................. Right Hand 22 in. (559 mm), 9

Blade Reel, without rollers.

62864.............................. Right Hand 22 in. (559 mm), 9

Blade Reel, without rollers.

62865.............................. Right Hand 22 in. (559 mm), 11

Blade Reel, without rollers.

62866.............................. Right Hand 22 in. (559 mm), 11

Blade Reel, without rollers.

62867.............................. Right Hand 22 in. (559 mm), 15

Blade Reel, without rollers.

62868.............................. Right Hand 22 in. (559 mm), 15

Blade Reel, without rollers.

Serial Number ................ An identification plate, like the one

shown, listing the serial number, is

attached to the frame of the reel.

Always provide the serial number of the unit when ordering

replacement parts or requesting service information.

2.2 CUTTING UNITS___________________________________________________________

Reel Diameter................. 5 in. (127 mm)

Reel Blade Options......... 7, 8, 9, 11, or 15 blades

Cutting Width .................. 18 in. (457 mm) or 22 in. (559

mm)

Height of Cut Range

Greens Reels............ 0.06 to 0.43 in. (1.6 to 11.1 mm)

Fairway Reels ........... 0.30 to 0.70 in. (7.6 to 18 mm)

Cutting Frequency

7 Blade ..................... 0.083 in./mph (1.314 mm/kph)

8 Blade ..................... 0.073 in./mph (1.150 mm/kph)

9 Blade ..................... 0.064 in./mph (1.010 mm/kph)

11 Blade ................... 0.053 in./mph (0.836 mm/kph)

15 Blade ................... 0.039 in./mph (0.613 mm/kph)

2.3 ACCESSORIES & SUPPORT LITERATURE ____________________________________

Contact your area Jacobsen Dealer for a complete listing of accessories and attachments.

Accessories

Orange Touch-up Paint (12 oz. spray) ......................554598

Rear Roller Cleaner .....................................................62820

High Cut Roller Kit (15/16”)..........................................68634

18 in. Reel Electric Drive Mounting Kit ....................4395138

18 in. Reel Hydraulic Drive Mounting Kit .................4395139

22 in. Fairway Reel Hydraulic Drive Mounting Kit....4395140

22 in. Fairway Reel Electric Drive Mounting Kit.......4395141

22 in. Greens Reel Hydraulic Drive Mounting Kit ....4395142

22 in. Greens Reel Electric Drive Mounting Kit........4395143

Magknife Kit

22 in. Medium Section Magknife Kit ........................ 4266571

22 in. Tournament Magknife Kit............................... 4266551

22 in. Super Tournament Magknife Kit.................... 4266570

Standard Turf Groomer

18 in. Turf Groomer Left Hand 1/4” Spacing ............... 67160

18 in. Turf Groomer Left Hand 1/2” Spacing ............... 67161

18 in. Turf Groomer Right Hand 1/2” Spacing............. 67162

22 in. Turf Groomer Left Hand 1/4” Spacing ............... 67163

22 in. Turf Groomer Right Hand 1/4” Spacing............. 67164

22 in. Turf Groomer Left Hand 1/2” Spacing ............... 67165

22 in. Turf Groomer Right Hand 1/2” Spacing............. 67166

CHARLOTTE, NC PRODUCT OF U.S.A.

A Textron Company

62857001651

CAUTION

Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the

equipment.

SPECIFICATIONS 2

Bi-Directional Groomer/Brush

Left Hand Electric Drive .............................................. 62936

Right Hand Electric Drive............................................ 62937

Left Hand Hydraulic Drive ........................................... 62938

Right Hand Hydraulic Drive......................................... 62939

18 in. (457 mm) 1/4 in. Spacing Groomer Shaft ......... 62907

18 in. (457 mm) 1/2 in. Spacing Groomer Shaft ......... 62940

22 in. (559 mm) 1/4 in. Spacing Groomer Shaft ......... 62905

22 in. (559 mm) 1/2 in. Spacing Groomer Shaft ......... 62906

18 in. (457 mm) Stiff Bristle Herringbone Brush ......... 62915

18 in. (457 mm) Medium Bristle Herringbone Brush... 62916

18 in. (457 mm) Soft Bristle Herringbone Brush ......... 62917

22 in. (559 mm) Stiff Bristle Herringbone Brush ......... 62909

22 in. (559 mm) Medium Bristle Herringbone Brush... 62910

22 in. (559 mm) Soft Bristle Herringbone Brush ......... 62911

18 in. (457 mm) 1/4 in. Spacing Groomer Roller ........ 62930

18 in. (457 mm) 1/2 in. Spacing Groomer Roller ........ 62941

18 in. (457 mm) Smooth Roller ................................... 62931

22 in. (559 mm) 1/4 in. Spacing Groomer Roller ........ 62927

22 in. (559 mm) 1/2 in. Spacing Groomer Roller ........ 62928

22 in. (559 mm) Smooth Roller ................................... 62929

Quick Change Kit ........................................................ 62934

Guide Reel Kit............................................................. 62935

18 Inch (457 mm) Reel Rear Rollers

2 in. Full Width Hollow Tube w/ Scraper ................. 4420307

2 in. Narrow Width Solid Tube w/ Scraper .............. 4420310

2-3/16 in. Full Width Solid Tube w/ Scraper................ 68674

22 Inch (559 mm) Reel Rear Rollers

2 in. Narrow Width Solid Tube w/ Scraper .............. 4420310

2 in. Full Width Hollow Tube w/ Scraper ................. 4420313

2 in. Full Width Solid Tube w/ Scraper.................... 4420317

2-1/2 in. Narrow Width Hollow Tube ....................... 4420337

2-1/2 in. Full Width Hollow Tube ............................. 4420338

2-1/2 in. Wide Width Hollow Tube........................... 4420342

18 Inch (457 mm) Reel Front Rollers

2 in. Hollow Smooth Tube........................................4108920

2 in. Solid Smooth Tube with Scraper .........................68626

2-3/16 in. Machined Steel Grooved .............................68616

2-3/16 in. Machined Aluminum Grooved .....................63318

3 in. Assembled Disc with Scraper ..............................67925

22 Inch (559 mm) Reel Front Rollers

2 in. Hollow Smooth Tube with Scraper.......................68530

2 in. Solid Smooth Tube with Scraper .........................68641

2 in. Assembled Disc ...................................................68527

2-3/16 in. Machined Steel Grooved .............................68613

2-3/16 in. Machined Aluminum Grooved .....................68614

2-1/4 in. Segmented Machined....................................68673

3 in. Assembled Disc .................................................123268

Scraper for 123268 Roller..........................................391202

Support Literature

Technical Repair Manual.........................................4269792

2 SPECIFICATIONS

2.4 DECLARATION OF INCORPORATION_________________________________________

DECLARATION OF INCORPORATION ▪ ДЕКЛАРАЦИЯ ЗА ОБЕДИНЕНИЕ ▪ PROHLÁŠENÍ O ZALOŽENÍ SPOLEČNOSTI ▪ INKORPORERINGSERKLÆRING ▪

INCORPORATIEVERKLARING ▪ KINNITUS ÜHENDAMISE KOHTA ▪ ASENNUSTODISTUS ▪ DECLARATION D’INCORPORATION ▪ EINBAUBESCHEINIGUNG ▪ ∆ΗΛΩΣΗ ΜΗ

ΣΥΜΜΟΡΦΩΣΗΣ ▪ BEÉPÍTÉSI NYILATKOZAT ▪ DICHIARAZIONE DI INCORPORAZIONE ▪ NOFORMĒŠANAS DEKLARĀCIJA ▪ PRIJUNGIMO DEKLARACIJA ▪

DIKJARAZZJONI

TA’ INKORPORAZZJONI ▪ DEKLARACJA ZGODNOŚCI DLA PODZESPOŁU ▪ DECLARAÇÃO DE INCORPORAÇÃO ▪ DECLARAŢIE DE ÎNCORPORARE ▪ VYHLÁSENIE O

ZABUDOVANÍ SÚČASTI ▪ IZJAVA ZA VGRADNJO ▪ DECLARACIÓN DE INCORPORACIÓN ▪ INBYGGNADSDEKLARATION

Business name and full address of the manufacturer ▪ Търговско име и пълен адрес на производителя ▪ Obchodní jméno a plná adresa výrobce ▪

Producentens firmanavn og fulde adresse ▪ Bedrijfsnaam en volledig adres van de fabrikant ▪ Tootja ärinimi ja täielik aadress ▪

Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des Herstellers ▪

Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo completo del fabbricante ▪

Uzņēmuma nosaukums un pilna ražotāja adrese ▪ Verslo pavadinimas ir pilnas gamintojo adresas ▪ Isem kummerċjali u indirizz sħiħ tal-fabbrikant ▪

Nazwa firmy i pełny adres producenta ▪ Nome da empresa e endereço completo do fabricante ▪ Denumirea comercială şi adresa completă a producătorului ▪

Obchodný názov a úplná adresa výrobcu ▪ Naziv podjetja in polni naslov proizvajalca ▪ Nombre de la empresa y dirección completa del fabricante ▪

Tillverkarens företagsnamn och kompletta adress

Textron Specialty Vehicles

1452 Marvin Griffin Road

Augusta, GA 30906, USA

Description and identification of the partly completed machinery. ▪ Описание и идентификация на частично завършените машини. ▪ Popis a identifikace částečně dokončeného strojního zařízení. ▪

Beskrivelse og identifikation af den delvist fremstillede maskine. ▪ Beschrijving en identificatie van de gedeeltelijk voltooide machinerie. ▪ Osaliselt komplekteeritud masina kirjeldus ja määratlus. ▪

Osittain kootun laitteiston kuvaus ja määrittely. ▪ Description et identification de la quasi-machine. ▪ Bezeichnung und Identifizierung der teilgefertigten Vorrichtung ▪ Περιγραφή και προσδιορισμός ημιτελούς μηχανήματος. ▪

A részlegesen megépített gép leírása és meghatározása. ▪ Descrizione e identificazione della quasi-macchina ▪ Da ļēji pabeigtas iekārtas apraksts un identifikācija. ▪ Dalinai užbaigtos įrangos aprašymas ir identifikacija. ▪

Deskrizzjoni u identifikazzjoni tal-makkinarju li jkun lest parzjalment. ▪ Opis i oznaczenie częściowo ukończonego urządzenia ▪ Descriç ão e identificação do equipamento parcial ▪

Descrierea şi identificarea echipamentului finalizat parţial ▪ Opis a identifikácia podzostavy strojného zariadenia ▪ Opis in identifikacija delno dokončanega stroja. ▪ Descripción e identificación de la maquinaria parcialmente completada. ▪

Beskrivning och identifiering av maskindelarna.

Product Code Serial Number Description

62857 6285701651 ~ 6285702999 Left Hand 18 in. (457 mm) 11 Blade TrueSet

™

Reel

62858 6285801651 ~ 6285802999

Left Hand 18 in. (457 mm) 15 Blade TrueSet

™

Reel

62298 6229801651 ~ 6229802999

Left Hand 18 in. (457 mm) 8 Blade TrueSet

™

Reel

62859 6285901651 ~ 6285902999

Right Hand 18 in. (457 mm) 8 Blade TrueSet

™

Reel

62299 6229901651 ~ 6229902999

Left Hand 18 in. (457 mm) 11 Blade TrueSet

™

Reel

62860 6286001651 ~ 6286002999 Right Hand 18 in. (457 mm) 11 Blade TrueSet

™

Reel

62861 6286101651 ~ 6286102999

Left Hand 22 in. (559 mm) 7 Blade TrueSet

™

Reel

62862 6286201651 ~ 6286202999 Right Hand 22 in. (559 mm) 7 Blade TrueSet

™

Reel

62863 6286301651 ~ 6286302999

Left Hand 22 in. (559 mm) 9 Blade TrueSet

™

Reel

62864 6286401651 ~ 6286402999

Right Hand 22 in. (559 mm) 9 Blade TrueSet

™

Reel

62865 6286501651 ~ 6286502999

Left Hand 22 in. (559 mm) 11 Blade TrueSet

™

Reel

62866 6286601651 ~ 6286602999

Right Hand 22 in. (559 mm) 11 Blade TrueSet

™

Reel

62867 6286701651 ~ 6286702999 Left Hand 22 in. (559 mm) 15 Blade TrueSet

™

Reel

62868 6286801651 ~ 6286802999

Right Hand 22 in. (559 mm) 15 Blade TrueSet

™

Reel

We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery. This shall be by hardcopy and shall be without prejudice to the intellectual property rights of the

manufacturer of the partly completed machinery.

Ние обещаваме да предадем, в отговор на основателно искане от националните органи, съответна информация за частично завършените машини. Това ще се осъществи чрез документ и няма да бъде в нарушение на правата за

интелектуална собственост на производителя на частично завършените машини.

Zavazujeme se na základě zdůvodněné žádosti ze strany národních úřadů poskytnout příslušné informace o částeč

ně dokončeném strojním zařízení. Informace budou předány v tištěné podobě a nepoškodí práva k duševnímu vlastnictví výrobce

týkající se částečně dokončeného strojního zařízení.

Som svar på en begrundet anmodning fra de nationale myndigheder forpligter vi os til at videregive oplysninger om den delvist fremstillede maskine. Dette bliver gjort i papirudgave og med forbehold for de immaterielle rettigheder, som indehaves af

producenten af den delvist fremstillede maskine.

We zijn van plan, in reactie op een redelijk verzoek van de nationale autoriteiten, relevante informatie over de gedeeltelijk voltooide machinerie te verzenden. Dit wordt gedaan in de vorm van fysieke kopieën en deze kopieën zullen onder alle

voorbehoud behoren tot de intellectuele eigendomsrechten van de fabrikant van de gedeeltelijk voltooide machinerie.

Me kohustume riigisiseste asutuste põhjendatud nõudmisel edastama asjakohast teavet osaliselt komplekteeritud masina kohta. Andmed edastatakse paberkandjal ning sellega ei tohi piirata osaliselt komplekteeritud masina tootja õigusi intellektuaalsele

omandile.

Sitoudumme toimittamaan osittain koottua laitteistoa koskevat olennaiset tiedot vastineena kansallisten viranomaisten perusteltuun pyyntöön. Tiedot toimitetaan paperitulosteena. Ne eivät rajoita valmistajan osittain koottua laitteistoa koskevia

immateriaalioikeuksia.

Nous nous engageons à fournir, en réponse à une demande rationnelle des autorités nationales, toute information appropriée concernant la quasi-machine. Ceci se fera par copie papier et sans préjuger des droits de propriété intellectuelle du fabricant

de la quasi-machine.

Wir verpflichten uns, auf eine begründete Aufforderung durch die nationalen Behörden hin, relevante Informationen über die teilgefertigte Maschine zu übersenden. Diese werden als Ausdruck übersandt und dürfen sich nicht nachteilig auf die Rechte

am geistigen Eigentum des Herstellers der teilgefertigten Maschine auswirken.

Αναλαμβάνουμε να μεταβιβάσουμε, προς απάντηση εύλογης αίτησης των εθνικών αρχών, τις σχετικές πληροφορίες όσον αφορά το ημιτελές μηχάνημα. Αυτό θα πρέπει να γίνει γραπτώς και δίχως να θίγει τα πνευματικά

δικαιώματα του κατασκευαστή

του ημιτελούς μηχανήματος.

Vállaljuk, hogy átadjuk – a nemzeti hatóságok megalapozott kérésére válaszul – a részlegesen megépített gépre vonatkozó információkat. Az információkat nyomtatott példányban adjuk át. A nyomtatott példány átadása a részlegesen megépített gép

gyártójának szellemi tulajdonjogaira tett kötelezettség nélkül történik.

Ci impegniamo a trasmettere, in risposta ad una richiesta adeguatamente motivata delle autorità nazionali, informazioni pertinenti sulla quasi-macchina. L’impegno sarà redatto in forma cartacea e lascerà impregiudicati i diritti di proprietà intellettuale del

fabbricante della quasi-macchina.

Atsaucoties uz pamatotu valsts iestāžu pieprasījumu, mēs apņemamies nodot saistīto informāciju par daļēji pabeigtu iekārtu. Tā būs cietā kopija un neradīs kaitējumus daļēji pabeigtās iekārtas ražotāja intelektuālā īpašuma tiesībām.

Atsakydami į nacionalinių valdžios organų užklausą, pateikiame informaciją apie dalinai užbaigtus mechanizmus. Šis dokumentas yra atspausdintas elektroninio originalo variantas ir be jokio išankstinio nusistatymo neturi tikslo pažeisti dalinai užbaigto

mechanizmo gamintojo intelektualinės nuosavybės teisių.

Aħna nwiegħdu li nippreżentaw, meta mitlubin mill-awtoritajiet nazzjonali, l-informazzjoni relevanti dwar il-makkinarju li jkun lest parzjalment. Din l-informazzjoni għandha tkun f’forma stampata u mingħajr preġudizzju għad-drittijiet tal-proprjetà intelletwali

tal-fabbrikant tal-makkinarju li jkun lest parzjalment.

Na uzasadnion

ą prośbę instytucji państwowych zobowiązujemy się do przekazania wszelkich informacji na temat częściowo ukończonego urządzenia. Będą one przekazane na piśmie. Strona przekazująca w/wym. dokumentację nie będzie rościła sobie

żadnych praw do własności intelektualnej producenta częściowo ukończonego urządzenia.

Na sequência de pedido razoável por parte das autoridades nacionais, comprometemo-nos a transmitir informações importantes sobre o equipamento parcial. Tal será feito por meio de hardcopy

e sem prejuízo para os direitos de propriedade intelectual do fabricante do equipamento parcial.

Ne angajăm să transmitem, ca răspuns la o solicitare motivată a autorităţilor naţionale, informaţii relevante privind echipamentul finalizat parţial. Aceasta se va efectua în format hârtie şi fără a aduce atingere drepturilor de proprietate intelectuală ale

producătorului echipamentului finalizat parţial.

Zaväzujeme sa, že na základe odôvodnenej požiadavky národných orgánov predložíme dôležité informácie o podzostave strojného zariadenia.

Musí to byť v tlačenej forme a bez ujmy na právach duševného vlastníctva výrobcu podzostavy strojného zariadenia.

Zavezujemo se, da bomo na utemeljeno zahtevo nacionalnih organov predložili zadevne informacije o delno dokončanem stroju. Informacije bodo v tiskani obliki in ne bodo posegale v pravice intelektualne lastnine proizvajalca delno dokončanega stroja.

Nos comprometemos a transmitir, en respuesta a una petición razonada por parte de las autoridades nacionales, información relevante sobre la maquinaria parcialmente completada. Ésta será transmitida en copia impresa y no afectará a los derechos

de propiedad intelectual del fabricante de la maquinaria parcialmente completada.

Vi åtar oss att vidarebefordra relevant information om maskindelarna vid en motiverad förfrågan från nationella myndigheter. Informationen ska erhållas i form av papperskopior och ska vara utan men för maskindelstillverkarens immateriella rättigheter.

SPECIFICATIONS 2

Partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of Directive 2006/42/EC.

Частично завършените машини не трябва да бъдат пускана в употреба, докато крайните машини, в които са вградени, не са приведени в съответствие с постановленията на директива 2006/

42/EО.

Částečně dokončené zařízení nesmí být uvedeno do provozu, dokud konečné zařízení, do kterého bylo uvedené zařízení namontováno, neodpovídá ustanovením Směrnice č. 2006/42/EC.

Delvist fremstillede maskiner må ikke indsættes i driften, før den endelige maskine, som den skal inkorporeres i, er blevet erklæret I overensstemmelse med bestemmelserne i Direktiv 2006/42/EF.

Gedeeltelijk voltooide machinerie mag niet in dienst worden genomen, totdat er voor de definitieve machinerie, waarvan gedeeltelijk voltooide machinerie onderdeel uitmaakt, een conformiteitsverklaring

is ontvangen onder de voorwaarden van Richtlijn 2006/42/EG.

Osaliselt komplekteeritud masinat ei tohi kasutusele võtta enne, kui lõplikult komplekteeritud masin, millega see ühendatakse, on tunnistatud direktiivi 2006/42/EÜ sätetele vastavaks.

Osittain koottua laitteistoa ei saa ottaa käyttöön, ennen kuin lopullinen laitteisto, johon se asennetaan, on vakuutettu direktiivin 2006/42/EY säännösten mukaiseksi.

La quasi-machine ne doit pas être mise en service avant que la machine finale dans laquelle elle doit être incorporée n’ait été déclarée conforme aux dispositions de la directive 2006/42/CE

Die teilgefertigte Vorrichtung darf erst in Betrieb genommen werden, wenn die Konformität der Maschine, in die sie eingebaut wird, entsprechend den Bestimmungen der Richtlinie 2006/42/EG erklärt

worden ist.

Θα πρέπει να εκτελεστεί σέρβις στο ημιτελές μηχάνημα μέχρι το τελικό μηχάνημα στο οποίο θα ενσωματωθεί να έχει τη δήλωση συμμόρφωσης, σύμφωνα με τις διατάξεις της Οδηγίας 2006/42/ΕΚ.

A részlegesen megépített gépet tilos üzembe helyezni mindaddig, amíg a 2006/42/EK irányelv rendelkezéseivel összhangban a részlegesen megépített gépet be nem építik a végleges változatba, és

erről nem nyilatkoznak.

La quasi-macchina non deve essere messa in servizio finché la macchina finale in cui deve essere incorporata non è stata dichiarata conforme, nel caso, alle disposizioni della Direttiva 2006/42/CE.

Daļēji pabeigtu iekārtu nedrīkst nodot ekspluatācijā, līdz galīgā iekārta, kurā tā ir jāiebūvē, ir deklarēta atbilstoši direktīvas Nr. 2006/42/EK noteikumiem.

Dalinai užbaigto mechanizmo negalima paleisti kol kiti mechanizmai, kurie dar bus prijungti, nebus patvirtinti kaip atitinkantys 2006/42/EC Direktyvos reikalavimus.

Il-makkinarju li jkun parzjalment lest ma g ħandux jibda jitħaddem sakemm il-makkinarju finali li fih ikun se ji ġi inkorporat ikun ġie ddikjarat konformi mad-dispożizzjonijiet tad-Direttiva 2006/42/KE.

Urządzenia częściowo ukończonego nie wolno użytkować aż do orzeczenia zgodności urządzenia w postaci kompletnej z wymaganiami dyrektywy 2006/42/WE.

O equipamento parcial não poderá entrar em funcionamento antes do mecanismo final no qual vai ser incorporado ser declarado como estando em conformidade com as condições da Directiva 2006/

42/CE.

Echipamentul finalizat parţial nu trebuie pus în funcţiune până ce echipamentul final în care va fi încorporat nu este declarat ca fiind conform cu prevederile Directivei 2006/42/CE.

Podzostava strojného zariadenia nesmie byť uvedená do prevádzky, pokiaľ finálne strojné zariadenie, ktorého sa stane súčasťou, nebude vyhlásené ako zhodné s ustanoveniami smernice 2006/42/ES.

Delno dokončanega stroja ni dovoljeno dati v obratovanje, dokler se dokončani stroj, v katerega se vgradi delno dokončani stroj, ne potrdi kot skladen z določbami Direktive 2006/42/ES.

La maquinaria parcialmente completada no debe ponerse en servicio hasta que la maquinaria final a la que debe incorporarse cumpla con las provisiones de la Directiva 2006/42/CE.

Maskindelarna får ej tas i bruk förrän maskinen som delen tillhör har deklarerats som överensstämmande med föreskrifterna I direktivet 2006/42/EG.

These accessories have been

designed to be fitted to the Jacobsen

127 mm (5 inch) reel mowers.

The place and date of the declaration ▪ Място и дата на декларацията ▪ Místo a datum prohlášení ▪ Sted og dato for erklæringen ▪

Plaats en datum van de verklaring ▪ Deklaratsiooni väljastamise koht ja kuupäev ▪ Vakuutuksen paikka ja päivämäärä ▪ Lieu et date de la déclaration ▪

Ort und Datum der Erklärung ▪ Τόπος και ημερομηνία δήλωσης ▪ A nyilatkozat kelte (hely és idő) ▪ Luogo e data della dichiarazione ▪

Deklarācijas vieta un datums ▪ Deklaracijos vieta ir data ▪ Il-post u d-data tad-dikjarazzjoni ▪ Miejsce i data wystawienia deklaracji ▪ Local e data da declaração ▪ Locul şi data declaraţiei ▪ Miesto a dátum

vyhlásenia ▪ Kraj in datum izjave ▪ Lugar y fecha de la declaración ▪ Plats och datum för deklarationen

Textron Specialty Vehicles

1452 Marvin Griffin Road

Augusta, GA 30906, USA

TBD

Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is established in

the Community.

Подпис на човека, упълномощен да състави декларацията от името на производителя, който поддържащ техническата документация и е оторизиран да изготви техническия файл и е

регистриран в общността.

Podpis osoby oprávněné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávněné sestavit technické soubory a založené v rámci Evropského společenství.

Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er

baseret i nærområdet.

Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is

gevestigd in het Woongebied.

Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus koostada tehniline toimik.

Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön.

Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et qui est implantée dans la Communauté.

Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen

zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.

Υπογραφή ατόμου εξουσιοδοτημένου για την σύνταξη της δήλωσης εκ μέρους του κατασκευαστή, ο οποίος κατέχει την τεχνική έκθεση και έχει την εξουσιοδότηση να ταξινομήσει τον τεχνικό φάκελο και

ο οποίος είναι διορισμένος στην Κοινότητα.

A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a műszaki dokumentációt őrzi, engedéllyel rendelkezik a műszaki fájl összeállításához, és aki a közösségben

letelepedett személy.

Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita

nella Comunità.

Tās personas paraksts, kura ir pilnvarota deklarācijas sastādīšanai ražotāja vārdā, kurai ir tehniskā dokumentācija, kura ir pilnvarota sagatavot tehnisko reģistru un kura ir apstiprināta Kopienā.

Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikė įgaliojimus sudaryti šią deklaraciją, ir kuris ją pasirašė, turi visą techninę informaciją ir yra įgaliotas sudaryti techninės informacijos dokumentą.

Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, għandha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-Komunità.

Podpis osoby upoważnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentację techniczną, upoważnioną do stworzenia dokumentacji technicznej oraz wyznaczonej ds.

wspólnotowych.

Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar o processo técnico e que está estabelecida na

Comunidade.

Semnătura persoanei împuternicite să elaboreze declaraţia în numele producătorului, care deţine documentaţia tehnică, este autorizată să compileze dosarul tehnic şi este stabilită în Comunitate.

Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracovať technické podklady a ktorá je umiestnená v Spoločenstve.

Podpis osebe, pooblaščene za izdelavo izjave v imenu proizvajalca, ki ima tehnično dokumentacijo in lahko sestavlja spis tehnične dokumentacije, ter ima sedež v Skupnosti.

Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el archivo técnico y que está establecido en la

Comunidad.

Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att sammanställa den tekniska informationen och

som är etablerad i gemenskapen.

2006/42/EC Annex II 1.A.2

Christian D. Clifford

Director of Engineering

Ransomes Jacobsen Limited

West Road, Ransomes Europark,

Ipswich, IP3 9TT, England

2006/42/EC Annex II 1.A.10

Christopher W. Spencer

Vice President of Engineering

Textron Specialty Vehicles

1452 Marvin Griffin Road

Augusta, GA 30906, USA

Certificate Number ▪ Номер на сертификат ▪ Číslo osvědčení ▪ Certifikatnummer ▪ Certificaatnummer ▪ Sertifikaadi number ▪ Hyväksyntänumero ▪

Numéro de certificat ▪ Bescheinigungsnummer ▪ Αριθμός Πιστοποιητικού ▪ Hitelesítési szám ▪ Numero del certificato ▪ Sertifikāta numurs ▪

Sertifikato numeris ▪ Numru taċ-Ċertifikat ▪ Numer certyfikatu ▪ Número do Certificado ▪ Număr certificat ▪ Číslo osvedčenia ▪ Številka certifikata ▪

Número de certificado ▪ Certifikatsnummer

4387946-DOI Rev A

United

Kingdom

Belgium

Bulgaria

Switzerland

China

Cyprus

Czech

Republic

Germany

Denmark

Estonia

Spain

Finland

France

Greece

Hungary

Iceland

Italy

Japan

Korea

Liechenstein

Lithuania

Latvia

Malta

Netherlands

Norway

Poland

Portugal

Romania

Russia

Sweden

Slovenia

Slovakia

Turkey

Ukrain

3 SETUP

3.1 GENERAL INFORMATION __________________________________________________

1. A mounting kit is required to install the reel onto your

mower and must be ordered separately. Check with

your dealer for the correct mounting kit for your

mower.

a. Callouts identified with a single letter, (A) through

(G), are part of the mower. Refer to the mower’s

manual for part numbers.

b. Callout with double letters, (AA) are part of the

reel. Refer to the parts list in this manual for parts

identification.

c. Callouts with triple letters, (AAA) through (ABF),

are parts of the reel mounting kit. Refer to the

parts list in this manual for parts identification.

2. If installed, remove existing reels from the mower,

using instructions in the mower’s manuals. Separate

lift yoke from the reels.

3. The front and rear rollers are not included with the

reel assembly and must be ordered separately.

Check with your dealer for rollers that are available

for your mower. Follow installation instructions

included with the rollers.

4. Figures show assembly of a left hand fairway reel.

Greens reels similar. Right hand reels are opposite.

3.2 REEL ACCESSORIES ______________________________________________________

Other accessories may also be available for your reel

such as Turf Groomer®, roller scrapers, and roller

brushes. Install these accessories before installing reels.

Follow instructions included in your mower’s manuals

and/or Turf Groomer’s Instruction Sheet for adjusting the

reel to bedknife and height of cut.

3.3 REEL TO MOWER ASSEMBLY_______________________________________________

1. Assemble the lift yoke (A) to the reel using hardware

included in the reel mounting kit.

a. For fairway reels, use two 3/8-16 x 1-1/4” screws

(AAA), lockwasher (AAB), flat washer (AAC)

and spacers (AAD) to assemble the lift yoke (A).

b. For greens reels, use two shoulder bolts (AAE)

to assemble the lift yoke (A).

2. Start the engine and fully lower the lift arms. Stop

the engine and remove the key.

3. Move the reel assembly in front of the lift arm (B).

4. If included with mower, assemble spring (F) onto the

lift yoke (A).

5. Lift the lift arm (B) and move the reel so that the lift

yoke (A) is aligned with the swivel housing (C).

6. Carefully lower lift arm (B) onto lift yoke (A).

7. Install pin (D) through the hole in the lift yoke (A)

and fasten the retaining clip. Install the cap (E) on

the swivel housing.

Figure 3A

AAA

AAB

AAC

AAD

AAE

AAD

SETUP 3

3.4 ELECTRIC REEL MOTOR ___________________________________________________

1. Assemble motor pins (AAF) and lock nuts (AAG) to

motor bearing housing (AA) using mounting holes

shown.

2. Apply grease to splines of reel coupler (AAH) and

assemble to end of reel shaft.

3. Slide motor (G) onto motor pins (AAF). Adjust reel

to align spline of coupler (AAH) to motor shaft

spline.

4. Secure motor by inserting motor clips (AAJ) into

slots in motor pins (AAF). Loops of motor clips

should face toward the center of the motor.

Figure 3B

3.5 HYDRAULIC REEL MOTOR__________________________________________________

1. Assemble motor pins (AAF) and lock nuts (AAG) to

motor bearing housing (AA) using mounting holes

shown.

2. Apply grease to splines of reel coupler (AAH) and

assemble to end of reel shaft.

3. Slide motor (G) onto motor pins (AAF). Adjust reel

to align spline of coupler (AAH) to motor shaft

spline.

4. Secure motor by inserting motor clips (AAJ) into

slots in motor pins (AAF). Loops of motor clips

should face toward the center of the motor.

Figure 3C

3.6 REEL STOP (GREENS REEL) ________________________________________________

1. Assemble reel mower stop (AAL) to the reel using

two 5/16-18 x 3/4” hex head screws (AAK) and

spiralock flange nuts (AAM).

Figure 3D

AAJ

AAF

Electric

Motor Holes

AAF

AAG

AAH

AAJ

AAF

AAG

AAH

Hydraulic

Motor Hole

AAK

AAL

AAM

3 SETUP

3.7 DOWN PRESSURE (FAIRWAY REEL) _________________________________________

1. Assemble down pressure bracket (AAN) to reel

frame using two 5/16-18 x 3/4” hex head screws

(AAK) and spiralock flange nuts (AAM).

2. Assemble jam nut (AAP) and ball joint (AAR) to

down pressure rod (AAS). Adjust ball joint so the

distance between center of ball joint hole and center

of rod hole is 8-15/16 ± 1/16 in. (227 mm ± 1.5

mm).

3. Assemble the adjustment pin (AAT) to the fourth

hole from ball joint in down pressure rod (AAS).

4. Slide flat washer (ABG) and spring (AAU) onto the

down pressure rod (AAS).

5. Assemble the down pressure assembly to the lift

yoke. Press the rod pin (AAV) into the rod (AAS).

The rod pin must be horizontal to the ground.

6. Assemble the ball joint (AAR) to the down pressure

bracket (AAN) using one 3/8-16 x 1-3/4” hex head

screw (AAW), spacer (AAX), lockwasher (AAY) and

nut (AAZ).

Figure 3E

3.8 COUNTERWEIGHT ________________________________________________________

1. Assemble counterweight (ABA) to bearing housing

using hardware included in the mounting kit.

a. For hydraulic drive reels, assemble

counterweight (ABA) using two 1/4-20 x 7/8 hex

head screws (ABB) and lockwashers (ABC).

b. For electric drive reels, assemble counterweight

(ABD) using one 1/4-20 x 3-1/4” hex head

screws (ABE), one 1/4-20 x 1” hex head screw

(ABF) and two lockwashers (ABC).

Figure 3F

AAK

8-15/16 in.

(227 mm)

AAM

ABG

AAN

AAP

AAR

AAS

AAT

AAU

AAV

AAW

AAX

AAY

AAZ

ABA

ABB

ABC

ABD

ABE

ABF

ADJUSTMENTS 4

4 ADJUSTMENTS

4.1 GENERAL ________________________________________________________________

1. Adjustments and maintenance should always be

performed by a qualified technician. If proper

adjustment cannot be made, contact an authorized

Jacobsen Dealer.

2. Replace, do not adjust, worn or damaged

components.

3. Long hair, jewelry or loose fitting clothing may get

tangled in moving parts.

4. Do not change speed limit settings or overspeed the

drive motors.

4.2 BEDKNIFE-TO-REEL _______________________________________________________

(Pre-adjustment Check)

1. Check the reel bearings for end play or radial play.

There should be no end play or radial play. See Section

4.10.

2. Inspect the reel blades and bedknife to insure good

sharp edges without bends or nicks.

a. The leading edge of the reel blades must be sharp,

free of burrs and show no signs of rounding off.

b. The bedknife and bedknife backing must be

securely tightened. The bedknife must be

straight and sharp.

c. A flat surface of at least 1/32 in. (0.8 mm)

minimum must be maintained on the front face of

the bedknife. Use a standard flat file to dress the

bedknife.

3. If wear or damage is beyond the point where the reel

or bedknife can be corrected by the lapping process,

they must be reground.

4. Proper reel-to-bedknife adjustment is critical. A gap of

0.001 to 0.003” (0.025 to 0.076 mm) must be

maintained across the entire length of the reel and

bedknife.

5. The reel must be parallel to the bedknife. An

improperly adjusted reel will lose its sharp edges

prematurely and may result in serious damage to the

reel and bedknife.

6. Grass conditions will also affect the adjustment.

a. Dry, sparse conditions will require a wider gap to

prevent heat buildup and damage to the reel and

bedknife.

b. High quality grass with a good moisture content

requires a closer gap (near zero).

Figure 4A

Figure 4B

WARNING

Before you clean, adjust, or repair this equipment,

disengage all drives, lower implements to the ground,

turn system power off, remove key from ignition switch,

and disconnect battery pack(s) to prevent injuries

Make sure the mower is parked on a solid and level

surface. Never work on a mower that is supported only

by the jack. Always use jack stands.

CAUTION

Be careful to prevent entrapment of the hands and

fingers between moving and fixed components of the

machine.

CAUTION

To prevent personal injury and damage to the cutting

edges, wear gloves and handle the reel and bedknife

with extreme care.

1/32”

(0.8 mm)

Leading Edge

4 ADJUSTMENTS

4.3 BEDKNIFE ADJUSTMENT __________________________________________________

1. Read Section 4.1 before making the adjustment.

2. Start adjustment at the leading end of the reel,

followed by the trailing end. The leading end of the

reel blades is that end which passes over the

bedknife first during normal reel rotation.

3. Use adjusters (B and C), to adjust gap. Rotate

adjusters (Clockwise) to close gap. Each click of the

adjuster moves the bedknife 0.001” (0.025 mm)

closer to the reel.

a. Slide a feeler gauge or shim stock 0.001” - 0.003”

(0.025 - 0.075 mm) between the reel blade and

the bedknife. Do not turn the reel.

b. Adjust the trailing end of the reel to the same

gap in a similar manner then recheck the

adjustment at the leading end.

c. When the reel is properly adjusted to the

bedknife, the reel will spin freely and you should

be able to cut a piece of newspaper, along the

full length of the reel, when the paper is held at

90° to the bedknife.

Figure 4C

4.4 CUTTING HEIGHT _________________________________________________________

Note: Always make the reel to bedknife adjustment

before adjusting height of cut. (Sections 4.2 and 4.3).

1. Set desired cutting height on the gauge (E).

a. Measure distance between the underside of

screw head and gauge block surface (F).

b. Adjust screw (H) to obtain desired height then

tighten the wing nut.

2. Loosen the nuts on the front roller brackets (G) just

enough to allow the adjuster knob (K) to raise or

lower the front roller.

3. Place gauge (E) across bottom of front and rear

rollers near one end of roller.

4. Slide the head of gauge screw (H) over the bedknife

(L) and adjust the knob (K) to close the gap between

the screw head and bedknife. Then tighten locknut

(G).

5. Repeat Steps 4 and 5 on opposite end. Complete

adjustment to one end before adjusting opposite end.

6. Tighten nuts (G) and recheck each end.

Figure 4D

NOTICE

Avoid excessive tightening or serious damage may

result to bedknife and reel blades. Reels must turn

freely.

ADJUSTMENTS 4

4.5 REEL BEARING ___________________________________________________________

Any radial play or excessive end play indicates bad

bearings, a weak tension spring or a backed off nut.

1. Check bearing housing mounting hardware. Tighten

or replace components as required. Carefully clean

threads with degreaser.

2. Apply a medium strength grade of Loctite to nut (P),

then thread nut onto the reel shaft until the nut is

1-27/32” (46 mm) from the end of the reel shaft.

3. Fill reel bearing housings with NLGI - Grade O

grease after adjusting spring.

Figure 4E

4.6 BEDKNIFE ADJUSTER SPRING ______________________________________________

For proper operation, bedknife adjuster spring should be

compressed to a dimension of 1-7/16 - 1-1/2 in. (36.5-38

mm).

To adjust spring compression, loosen or tighten nut (R) to

obtain a distance of 1-7/16 - 1-1/2 in. (36.5-38 mm).

After adjusting spring, check reel to bedknife adjustment.

Figure 4F

4.7 BEDKNIFE ADJUSTER TENSION _____________________________________________

Remove hair pin (U) and fully loosen, then tighten slotted

nut (S) to remove clearance (no end play) between

components. Continue to tighten nut until next slot in nut

aligns with hole in bedknife adjuster rod (T). Install hair

pin.

Check torque required to rotate adjuster rod (T).

Maximum torque should be 24 in. lb. (2 ft. lb.) (2.7 Nm).

After adjusting nut, check reel to bedknife adjustment.

Figure 4G

GKV-11

1-27/32 in.

(46 mm)

1-7/16 to 1-1/2 in.

(3.65 to 3.8 cm)

NOTICE

Overtightening slotted nut (S) will make bedknife

adjuster rod (T) difficult to adjust.

4 ADJUSTMENTS

4.8 GRINDING BEDKNIFE ______________________________________________________

Bedknife can be lowered out of the reel for grinding

without completly removing the bedknife assembly.

1. Remove cotter pin (U), slotted nut (S), bellville

washer (V), shim washer (W-If required), and half

trunnion (X). See Figure 4G

4. Press down on adjuster end of rod (T) to rotate other

end of the adjuster out of the bedknife finger.

5. Rotate bedknife backing to access the reel and

bedknife for grinding.

6. After grinding, assemble bedknife using reverse

order of removal. Check adjustment of bedknife

adjuster tension (Section 4.7), and reel to bedknife

adjustment (Section 4.3).

4.9 DOWN PRESSURE SPRING _________________________________________________

Each fairway reel is has a down pressure spring. Down

pressure improves the cutting quality by contact between

the reel and ground. Check and adjust the down pressure

any time the HOC is changed or to improve the cut for the

best performance.

1. Lift the reels to the transport position. Put the

adjustment pin in 4th hole from ball joint. Lower the

reels onto a flat surface before you measure the

down pressure.

2. Set the distance between the ball joint center and

the rod pin center to 8-15/16 in. ± 1/16 in. (22.7 mm

± 0.2 cm). To adjust the length, loosen the jam nut

and rotate the rod into or out of the ball joint.

3. Measure length of spring as shown on all 5 reels.

Record the shortest spring dimension. Adjust the

ball joint to get the other springs to the same

dimension ± 1/16 in. (0.2 cm). The rod pin must be

horizontal, then tighten the jam nut.

4. To adjust the down pressure, move the adjustment

pin one hole toward the spring to increase the down

pressure on the rear roller. Move the adjustment pin

one hole away from the spring to decrease the

down pressure on the rear roller.

Figure 4H

Ball

Joint

Jam

Nut

Adjustment

8-15/16 in.

(22.7 cm)

Rod

ADJUSTMENTS 4

4.10 TORQUE SPECIFICATION___________________________________________________

Jacobsen uses Grade 5 Plated bolts as standard, unless otherwise noted. For tightening plated bolts, use the value

given for lubricated.

NOTICE

All torque values included in these charts are approximate and are for reference only. Use of these torque values is

at your sole risk. Jacobsen is not responsible for any loss, claim, or damage arising from the use of these charts.

Extreme caution should always be used when using any torque value.

AMERICAN NATIONAL STANDARD FASTENERS

SIZE UNITS GRADE 5 GRADE 8 SIZE UNITS GRADE 5 GRADE 8

Lubricated Dry Lubricated Dry Lubri-

cated

Dry Lubri-

cated

Dry

#6-32 in-lb (Nm) – 20 (2.3) – – 7/16-14 ft-lb (Nm) 37 (50.1) 50 (67.8) 53 (71.8) 70 (94.9)

#8-32 in-lb (Nm) – 24 (2.7) – 30 (3.4) 7/16-20 ft-lb (Nm) 42 (56.9) 55 (74.6) 59 (80.0) 78 (105)

#10-24 in-lb (Nm) – 35 (4.0) – 45 (5.1) 1/2-13 ft-lb (Nm) 57 (77.2) 75 (101) 80 (108) 107 (145)

#10-32 in-lb (Nm) – 40 (4.5) – 50 (5.7) 1/2-20 ft-lb (Nm) 64 (86.7) 85 (115) 90 (122) 120 (162)

#12-24 in-lb (Nm) – 50 (5.7) – 65 (7.3) 9/16-12 ft-lb (Nm) 82 (111) 109 (148) 115 (156) 154 (209)

1/4-20 in-lb (Nm) 75 (8.4) 100 (11.3) 107 (12.1) 143 (16.1) 9/16-18 ft-lb (Nm) 92 (124) 122 (165) 129 (174) 172 (233)

1/4-28 in-lb (Nm) 85 (9.6) 115 (13.0) 120 (13.5) 163 (18.4) 5/8-11 ft-lb (Nm) 113 (153) 151 (204) 159 (215) 211 (286)

5/16-18 in-lb (Nm) 157 (17.7) 210 (23.7) 220 (24.8) 305 (34.4) 5/8-18 ft-lb (Nm) 128 (173) 170 (230) 180 (244) 240 (325)

5/16-24 in-lb (Nm) 173 (19.5) 230 (26.0) 245 (27.6) 325 (36.7) 3/4-10 ft-lb (Nm) 200 (271) 266 (360) 282 (382) 376 (509)

3/8-16 ft-lb (Nm) 23 (31.1) 31 (42.0) 32 (43.3) 44 (59.6) 3/4-16 ft-lb (Nm) 223 (302) 298 404 315 (427) 420 (569)

3/8-24 ft-lb (Nm) 26 (35.2) 35 (47.4) 37 (50.1) 50 (67.8) 7/8-14 ft-lb (Nm) 355 (481) 473 (641) 500 (678) 668 (905)

METRIC FASTENERS

SIZE UNITS

Non Critical

Fasteners

into

Aluminum

Lubricated Dry Lubricated Dry Lubricated Dry Lubricated Dry

M4 Nm (in-lb)––––––3.83 (34)5.11 (45)2.0 (18)

M5 Nm (in-lb) 1.80 (16) 2.40 (21) 4.63 (41) 6.18 (54) 6.63 (59) 8.84 (78) 7.75 (68) 10.3 (910 4.0 (35)

M6 Nm (in-lb) 3.05 (27) 4.07 (36) 7.87 (69) 10.5 (93) 11.3 (102) 15.0 (133) 13.2 (117) 17.6 (156) 6.8 (60)

M8 Nm (in-lb) 7.41 (65) 9.98 (88) 19.1 (69) 25.5 (226) 27.3 (241) 36.5 (323) 32.0 (283) 42.6 (377) 17.0 (150)

M10 Nm (ft-lb) 14.7 (11) 19.6 (14) 37.8 (29) 50.5 (37) 54.1 (40) 72.2 (53) 63.3 (46) 84.4 (62) 33.9 (25)

M12 Nm (ft-lb) 25.6 (19) 34.1 (25) 66.0 (48) 88.0 (65) 94.5 (70) 125 (92) 110 (81) 147 (108) 61.0 (45)

M14 Nm (ft-lb) 40.8 (30) 54.3 (40) 105 (77) 140 (103) 150 (110) 200 (147) 175 (129) 234 (172) 94.9 (70)

4.6

8.8

10.9

12.9

4127335

4181860

TRUESET™ REEL

6.1 Outer Reel

Serial No. All

> Change from previous revision

TRUESET™ REEL

Item Part No. Qty. Description Serial Numbers/Notes

REF 1 Inner Reel See 7.1

2 1002224 2 Zerk Bolt

3 365246 2 Shoulder Bolt

4 2810043 1 Shield, Grass

5 4181860 1 Decal, Read Manual for Service

6 4127335 2 Decal, Danger

7 352737 2 Set Screw, 1/4-20 x 7/8” Grade 8

8 403782 2 Screw, 1/4-20 x 3/4” Truss Head

9 453023 2 Flat Washer, 1/4

10 446130 2 Lockwasher, 1/4 Heavy

11 443102 4 Nut, 1/4-20 Hex

12 3008438 1 Bracket, Right Side Front Roller

13 3008439 1 Bracket, Left Side Front Roller

14 441674 2 Carriage Bolt, 5/16-18 x 1-3/4”

15 445795 4 Nut, 5/16-18 Spiralock Flange

16 343616 2 Stud, Front Roller Adjuster

17 3005692 2 Knob, Front Roller Adjuster

18 367164 1 Spacer

19 453011 1 Flat Washer, 3/8

20 446142 1 Lockwasher, 3/8 Heavy

21 400294 1 Screw, 3/8-24 x 1” Hex Head

18 Inch Service Reels

22 Inch Service Reels

Part Number Description

4119512 18” RH 8 Blade Reel

4170220 18” LH 11 Blade Reel

4119513 18” RH 11 Blade Reel

Part Number Description

5001100 22” RH 9 Blade Reel

5001101 22” LH 11 Blade Reel

4391646 18” LH 8 Blade Reel

5001099 22” LH 9 Blade Reel

5003054 22” RH 7 Blade Reel

5003053 22” LH 7 Blade Reel

5001102 22” RH 11 Blade Reel

4225504 18” LH 15 Blade Reel

4225505 22” LH 15 Blade Reel

4269791 22” RH 15 Blade Reel

Standard Style Bedknives

(Secured with screws)

Part Number Description

5000098 18” Low Profile

■ 4118902 18” Medium Section

● 5002888 18” Super Tournament

4234901 18” Championship

◆ 503478 22” Low Profile

503477 22” High Profile

503460 22” Heavy Section

503479 22” To urnament

4234900 22” Championship

▲ 5003150 22” Medium Section

● 5002887 22” Super Tournament

▲ Standard Bedknife (7 Blade)

■ Standard Bedknife (8 Blade)

◆ Standard Bedknife (9 Blade)

● Standard Bedknife (11 and 15 Blade)

GREENS KING IV REEL

7.1 Inner Reel

Serial No. All

Pagina se încarcă ...

Jacobsen 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868 Instruction Sheet

Marca: Jacobsen

Model: 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868

Tip: Instruction Sheet

Descărcați PDF

raport

în alte limbi

English: Jacobsen 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868

Jacobsen 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868 Instruction Sheet

Jacobsen 62298 62299 62857 62858 62859 62860 62861 62862 62863 62864 62865 62866 62867 62868 Instruction Sheet

în alte limbi

Lucrări conexe

Alte documente