12 www.raider.bg
General guidelines for safe operation.
Read all instructions carefully. Failure of the nature following instructions can cause electric shock, re and / or severe
injuries. Keep these instructions in a safe place.
1. Safety in the workplace.
1.1. Keep your workplace clean and well lit. Disarray and poor lighting may contribute to the occurrence of an accident.
1.2. Do not operate in an environment where the impact drill with an increased risk of an explosion in the vicinity of
ammable liquids, gases or powders.
During operation of the impact drill can be separated sparks that can ignite powders or fumes.
1.3. Keep children and bystanders at a safe distance while working with the impact drill.
If your attention is diverted, you may lose control over the impact drill.
2. Safety when working with electricity.
2.1. Plug of the impact drill must be suitable for contact. In no case is allowed to modify the structure of the plug. When
working with electrical zero, do not use plug adapters.
Using original plugs and sockets reduces the risk of electric shock.
2.2. Avoid touching your body to earthed bodies, e.g. pipes, heaters, stoves and refrigerators. When your body is
grounded, risk of electric shock is greater.
Protect your impact drill from rain and moisture.
Penetration of water into the impact drill increases the risk of electric shock.
2.3. Do not use a power cord for the purposes for which it is not provided, e.g. to bear the impact drill for cable or
removing the plug from the outlet. Protect cords from heat, oil, contact with sharp edges or points of mobile machines.
Damaged or twisted cables increase the risk of electric shock.
2.4. When you work with the impact drill out, switch the machine only in installations equipped with electric switch “Fi”
RCD (Residual Current Device). RCD must be no more than 30 mA. Use an extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of electric shock.
2.5. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3. Safe way of working.
3.1. Be concentrated, watch their actions carefully and act cautiously and prudently. Do not use the impact drill, when you
are tired or under the inuence of drugs, alcohol or narcotic drugs.
A moment of distraction at work impact drill may have the effect of extremely serious injuries.
3.2. Work with protective work clothing and always with safety glasses.
Wearing suitable for drilling and the activities of personal protective equipment, such as respiratory masks, healthy,
tightly closed shoes grapple with a stable, protective helmet and silencers (hearing protectors), reduces the risk of accident.
3.3. Avoid the danger of switch on the impact drill inadvertently. Before you turn the plug into the power supply network,
make sure the trigger switch is in position “off”. If, when you carry the impact drill, keep your nger on the trigger switch, or if
you submit a voltage of the impact drill, where it is included, there is the risk of accident.
3.4. Before you turn on the impact drill, make sure that you have removed all of her utilities and wrenches.
Utilities, forgotten rotating unit can cause injuries.
3.5. Avoid unnatural positions of the body. Work in a stable position of the body at any time and keep the balance. So you
can control the impact drill better and safer if unexpected situations arise.
3.6. Work with appropriate clothing. Do not operate with loose clothing or ornaments. Keep your hair, clothes and gloves
at a safe distance from rotating units of the impact drill. Robes, jewelry, long hair can be caught and carried away by chuck.
3.7. If possible use an external aspiration system, make sure it is switched on and functioning properly. Use of the
aspiration system reduces the risks due to the discharge dust at work.
4. Care to impact drill.
4.1. Do not overload the impact drill. Use only the impact drill in accordance with its intended purpose. Will operate better
and safer when using the appropriate impact drill manufacturer in the specied range of load.
4.2. Do not use impact drill, whose starting switch is damaged.
Impact drill, which can not be excluded and included as provided by the manufacturer, is dangerous and must be
repaired.
4.3. Before you modify the settings of the impact drill, working to replace instruments and ancillary devices, and for a long
time when you will not use the impact drill, unplug the plug from the supply network. This measure eliminates the danger of
triggering of the impact drill inadvertently.
4.4. Keep impact drill in places where they could not be reached by children. Do not let it be used by persons who are not