Samsung AC120RXADNG/EU Manual de utilizare

Air conditioner

Installation manual

AC***RXAD*G

• Thank you for purchasing this Samsung air conditioner.

• Before operating this unit, please read this manual carefully and retain it for future

reference.

2 English

Contents

Safety Information 4

General information 4

Installing the unit 5

Power supply line, fuse or circuit breaker 6

Installation Procedure 7

Step 1 Choosing the installation location 7

Step 2 Fixing the outdoor unit in place 10

Step 3 Connecting the power cables, communication cable, and controllers 11

Step 4 Optional: Extending the power cable 17

Step 5 Connecting the refrigerant pipe 19

Step 6 Optional: Cutting and flaring the pipes 20

Step 7 Installing oil traps 21

Step 8 Connecting up and removing air in the circuit 22

Step 9 Adding refrigerant (R-32) 23

Step 10 Performing the gas leak test 26

Step 11 Connecting the drain hose to the outdoor unit 27

Step 12 Insulating the refrigerant pipes 27

Step 13 Checking the earthing 28

Step 14 Performing final check and trial operation 29

Extra procedures 32

Pumping down refrigerant 32

Relocating the indoor and outdoor units 32

Using the stop valve 33

3English

Maintence Procedures 34

Performing the gas leak tests for repair 34

Decommissioning 34

Appendix 35

Troubleshooting 35

Technical specifications 36

COMMISSION DELEGATED REGULATION (EU) No 626/2011

i)

37

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.

charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate

these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material

resources.

Household users should contact either the retailer where they purchased this product, or their local government

office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This

product and its electronic accessories should not be mixed with other commercial wastes for disposal.

For information on Samsung’s environmental commitments and product-specific regulatory obligations, e.g. REACH,

WEEE, Batteries, visit: www.samsung.com/uk/aboutsamsung/sustainability/environment/our-commitment/data/

4

Safety Information

English

Safety Information

WARNING

• Hazards or unsafe practices that may result in severe

personal injury or death.

CAUTION

• Hazards or unsafe practices that may result in minor

personal injury or property damage.

Carefully follow the precautions listed below because

they are essential to guarantee the safety of the

equipment.

WARNING

• Always disconnect the air conditioner from the power

supply before servicing it or accessing its internal

components.

• Verify that installation and testing operations are

performed by qualified personnel.

• Verify that the air conditioner is not installed in an

easily accessible area.

General information

WARNING

• Carefully read the content of this manual before installing

the air conditioner and store the manual in a safe place in

order to be able to use it as reference after installation.

• For maximum safety, installers should always carefully

read the following warnings.

• Store the operation and installation manual in a safe

location and remember to hand it over to the new owner

if the air conditioner is sold or transferred.

• This manual explains how to install an indoor unit with a

split system with two SAMSUNG units. The use of other

types of units with different control systems may damage

the units and invalidate the warranty. The manufacturer

shall not be responsible for damages arising from the use

of non compliant units.

• The manufacturer shall not be responsible for damage

originating from unauthorized changes or the improper

connection of electric and requirements set forth in the

“Operating limits” table, included in the manual, shall

immediately invalidate the warranty.

• The air conditioner should be used only for the

applications for which it has been designed: the indoor

unit is not suitable to be installed in areas used for

laundry.

• Do not use the units if damaged. If problems occur, switch

the unit off and disconnect it from the power supply.

• In order to prevent electric shocks, fires or injuries, always

stop the unit, disable the protection switch and contact

SAMSUNG’s technical support if the unit produces smoke,

if the power cable is hot or damaged or if the unit is very

noisy.

• Always remember to inspect the unit, electric connections,

refrigerant tubes and protections regularly. These

operations should be performed by qualified personnel

only.

• The unit contains moving parts, which should always be

kept out of the reach of children.

• Do not attempt to repair, move, alter or reinstall the unit.

If performed by unauthorized personnel, these operations

may cause electric shocks or fires.

• Do not place containers with liquids or other objects on

the unit.

• All the materials used for the manufacture and packaging

of the air conditioner are recyclable.

• The packing material and exhaust batteries of the remote

controller(optional) must be disposed of in accordance

with current laws.

• The air conditioner contains a refrigerant that has to be

disposed of as special waste. At the end of its life cycle,

the air conditioner must be disposed of in authorized

centres or returned to the retailer so that it can be

disposed of correctly and safely.

• Wear protective equipment (such as safety gloves,

goggles, and headgear) during installation and

maintenance works. Installation/repair technicians may be

injured if protective equipment is not properly equipped.

• Do not use means to accelerate the defrost operation or to

clean, other than those recommended by Samsung.

• Do not pierce or burn.

• Be aware that refrigerants may not contain an odour.

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

5English

Safety Information

• For use in Europe: This appliance can be used by children

aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with

the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

Installing the unit

WARNING

IMPORTANT: When installing the unit, always remember

to connect first the refrigerant tubes, then the electrical

lines.

• Upon receipt, inspect the product to verify that

it has not been damaged during transport. If the

product appears damaged, DO NOT INSTALL it and

immediately report the damage to the carrier or

retailer (if the installer or the authorized technician

has collected the material from the retailer.)

• After completing the installation, always carry out a

functional test and provide the instructions on how to

operate the air conditioner to the user.

• Do not use the air conditioner in environments with

hazardous substances or close to equipment that

release free flames to avoid the occurrence of fires,

explosions or injuries.

• Do not install the product in a place where

thermohygrostat is needed (such as server room,

machinery room, computer room, etc.) Those places

do not provide guaranteed operation condition of the

product therefore performance can be poor in these

places.

• Do not install the product in a ship or a vehicle

(such as a campervan). Salt, vibration or other

environmental factor may cause the product

malfunction, electric shock or fire.

• Our units should be installed in compliance with the

spaces shown in the installation manual, to ensure

accessibility from both sides and allow repairs

or maintenance operations to be carried out. The

unit’s components should be accessible and easy to

disassemble without endangering people and objects.

• For this reason, when provisions of the installation

manual are not complied with, the cost required to

access and repair the units (in SAFETY CONDITIONS,

as set out in prevailing regulations) with harnesses,

ladders, scaffolding or any other elevation system

will NOT be considered part of the warranty and will

be charged to the end customer.

• The outdoor unit shall be installed in an open space

that is always ventilated.

• The local gas regulations shall be observed.

• To handle, purge, and dispose the refrigerant, or

break into the refrigerant circuit, the worker should

have a certificate from an industry-accredited

authority.

• While in installation or relocation of the product, do

not mix the refrigerant with other gases including air

or unspecified refrigerant. Failure to do so may cause

pressure increase to result in rupture or injury.

• Do not cut or burn the refrigerant container or

pipings.

• Use clean parts such as manifold gauge, vacuum

pump, and charging hose for the refrigerant.

• Installation must be carried out by qualified personnel

for handling the refrigerant. Additionally, reference

the regulations and laws.

• Be careful not to let foreign substances (lubricating

oil, refrigerant, water, etc.) enter the pipings.

• When mechanical ventilation is required, ventilation

openings shall be kept clear of obstruction.

• For disposal of the product, follow the local laws and

regulations.

• Do not work in a confined place.

• The work area shall be blocked.

• The refrigerant pipings shall be installed in the

position where there are no substances that may

result in corrosion.

• The following checks shall be performed for

installation:

– The charging amount depends on the room size.

– The ventilation devices and outlets are operating

normally and are not obstructed.

– Markings and signs on the equipment shall be

visible and legible.

• Upon leakage of the refrigerant, ventilate the room.

When the leaked refrigerant is exposed to flame, it

may cause generation of toxic gases.

6

Safety Information

English

Safety Information

• Make sure that the work area is safe from flammable

substances.

• To purge air in the refrigerant, be sure to use a

vacuum pump.

• Note that the refrigerant has no odour.

• The units are not explosion proof so they must be

installed with no risk of explosion.

• This product contains fluorinated gases that

contribute to global greenhouse effect. Accordingly,

do not vent gases into the atmosphere.

• For installation with handling the refrigerant(R-32),

use dedicated tools and piping materials. Working

pressure of R-32 is higher than R410A, So failure to

use the dedicated tools and piping materials may

cause rupture or injury. Furthermore, it may cause

serious accidents such as water leakage, electric

shock or fire.

• Servicing shall be performed as recommended by the

manufacturer. In case other skilled persons are joined

for servicing, it shall be carried out under supervision

of the person who is competent in handling

flammable refrigerants.

• For servicing the units containing flammable

refrigerants, safety checks are required to minimise

the risk of ignition.

• Servicing shall be performed following the controlled

procedure to minimize the risk of flammable

refrigerant or gases.

• Do not install where there is a risk of combustible gas

leakage.

• Do not place heat sources.

• Be cautious not to generate a spark as follows:

– Do not remove the fuses with power on.

– Do not disconnect the power plug from the wall

outlet with power on.

– It is recommended to locate the outlet in a high

position. Place the cords so that they are not

tangled.

• If the indoor unit is not R-32 compatible, an error

signal appears and the unit will not operate.

• After installation, check for leakage. Toxic gas may

be generated and if it comes into contact with an

ignition source such as fan heater, stove, and cooker,

cylinders, make sure that only the refrigerant

recovery cylinders are used.

• Never directly touch any accidental leaking

refrigerant. It could result in severe wounds caused

by frostbite.

Power supply line, fuse or circuit

breaker

WARNING

• Always make sure that the power supply is compliant

with current safety standards. Always install the air

conditioner in compliance with current local safety

standards.

• Always verify that a suitable earthing connection is

available.

• Verify that the voltage and frequency of the power

supply comply with the specifications and that the

installed power is sufficient to ensure the operation

of any other domestic appliance connected to the

same electric lines.

• Always verify that the cut-off and protection switches

are suitably dimensioned.

• Verify that the air conditioner is connected to the

power supply in accordance with the instructions

provided in the wiring diagram included in the

manual.

• Always verify that electric connections (cable entry,

section of leads, protections…) are compliant with

the electric specifications and with the instructions

provided in the wiring scheme. Always verify that all

connections comply with the standards applicable to

the installation of air conditioners.

• Devices disconnected from the power supply should

be completely disconnected in the condition of

overvoltage category.

• Be sure not to perform power cable modification,

extension wiring, and multiple wire connection.

– It may cause electric shock or fire due to poor

connection, poor insulation, or current limit

override.

– When extension wiring is required due to power

line damage, refer to Step 4 Optional: Extending

the power cable in the installation manual.

7English

Installation Procedure

Step 1 Choosing the installation

location

WARNING

• Because your air conditioner contains R-32 refrigerant,

make sure that it is installed, operated, and stored it in

a room whose floor area is larger than the minimum

required floor area specified in the following table:

Minimum required room area (A, m²)

m (kg)

Ceiling-mounted

type

Wall-mounted

type

Floor-standing

type

≤ 1.842 No requirement

1.843 3.64 4.45 28.9

1.9 3.75 4.58 30.7

2.0 3.95 4.83 34.0

2.2 4.34 5.31 41.2

2.4 4.74 5.79 49.0

2.6 5.13 6.39 57.5

2.8 5.53 7.41 66.7

3.0 5.92 8.51 76.6

3.2 6.48 9.68 87.2

3.4 7.32 10.9 98.4

3.6 8.20 12.3 110

3.8 9.14 13.7 123

4.0 10.1 15.1 136

4.2 11.2 16.7 150

4.4 12.3 18.3 165

4.6 13.4 20.0 180

4.8 14.6 21.8 196

5.0 15.8 23.6 213

5.2 17.1 25.6 230

– m : Total refrigerant charge in the system

– A :

Minimum required room area

• IMPORTANT: it’s mandatory to consider either the

table 1 or taking into consideration the local law

regarding the minimum living space of the premises.

• Minimum installation height of indoor unit is 0.6 m

for floor mounted, 1.8 m for wall, 2.2 m for ceiling.

Installation location requirements

• Do not place the outdoor unit on its side or upside

down. Failing to do so may cause the compressor

lubrication oil to run into the cooling circuit and lead

to a serious damage to the unit.

• Install the unit in a well-ventilated location away

from direct sunlight or strong winds.

• Install the unit in a location that would not obstruct

any passageways or thoroughfares.

• Install the unit in a location that would not

inconvenience or disturb your neighbors, as they

could be affected by the noise or the airflow coming

from the unit.

• Install the unit in a location where the pipes and the

cables can be easily connected to the indoor unit.

• Install the unit on a flat, stable surface that can

withstand the weight of the unit. Otherwise, the unit

can generate noise and vibration during operation.

• Install the unit so that the air flow is directed towards

the open area.

• Maintain sufficient clearance around the outdoor unit,

especially from a radio, computer, stereo system, etc.

Fuse

Control

1 m or more

1.5 m or more

300 mm

Stereo

Computer etc

Outdoor Unit

200 mm

Air Guide Duct (This product is not provided by Samsung)

Indoor Unit

• Install the unit at a height where its base can be

firmly fixed in place.

• Make sure that the water dripping from the drain

hose runs away correctly and safely.

8

Installation Procedure

English

Installation Procedure

CAUTION

• You have just purchased a system air conditioner

and it has been installed by your installation

specialist.

• This device must be installed according to the

national electrical rules.

• If your outdoor unit exceeds a net weight of 60 kg,

do not install it on a suspended wall, but stand it

on a floor.

• When installing the outdoor unit at the seaside, make

sure that it is not directly exposed to sea breeze. If

you cannot find an adequate place free from direct

sea breeze, construct a protection wall or a protective

fence.

– Install the outdoor unit in a place (such as near

buildings etc.) where it can be prevented from sea

breeze. Failure to do so may cause a damage to

the outdoor unit.

Sea breeze Sea breeze

Sea Sea

Outdoor Unit Outdoor Unit

• If you cannot avoid installing the outdoor unit at the

seaside, construct a protection wall around to block

the sea breeze.

• Construct a protection wall with a solid material such

as concrete to block the sea breeze. Make sure that the

height and the width of the wall are 1.5 times larger

than the size of the outdoor unit. Also, secure a space

larger than 700 mm between the protection wall and

the outdoor unit for exhausted air to ventilate.

Protection wall

Outdoor Unit

Sea breeze

Sea

CAUTION

• Depending on the condition of power supply, unstable

power or voltage may cause malfunction of the parts

or control system. (At the ship or places using power

supply from electric generator...etc)

• Install the unit in a place where water can drain smoothly.

• If you have any difficulty finding installation location as

prescribed above, contact your manufacturer for details.

• Be sure to clean the sea water and the dust on the

heat exchanger of the outdoor unit and apply a

corrosion inhibitor on it. (At least once in a year.)

• Check the condition of the product periodically.

– Check the installation site every 3 months and

perform anti-corrosion treatment such as R-Pro

supplied by SAMSUNG (Code: MOK-220SA) or

commercial water repellent grease and wax, etc.,

based on the product condition.

– When the product is to be shut down for a long

period of time, such as off-peak hours, take

appropriate measures like covering the product.

• If the product installed within 500m of seashore,

special anti-corrosion treatment is required.

࢜

Please contact your local SAMSUNG representative

for further details.

Outdoor unit dimensions

(Unit: mm)

A Type

AC100RXADKG/AC100RXADNG/AC120RXADKG/AC120RXADNG

998

977

537

528

620

940

330

384

360

675

B Type

AC140RXADKG/AC140RXADNG

620

330

384

360

1210

1185

940

567

558

675

9English

Installation Procedure

Minimum clearances for the outdoor unit

When installing 1 outdoor unit

(Unit: mm)

300 or more

1500 or more

300 or

more

600 or

more

300 or

more

2000

or more

1500

or more

600

or more

300

or more

1500

or more

300 or

more

When installing more than 1 outdoor unit

(Unit: mm)

1500

or more

600

or more

3000

or more

3000

or more

300

or more

600

or more

600

or more

1500

or more

300

or more

1500 or more

600

or more

600

or more

300

or more

600

or more

600

or more

600

or more

300

or more

300 or more

500 or more 500 or more

CAUTION

• The outdoor unit must be installed according to the

specified distances in order to permit accessibility

from each side, to guarantee correct operation,

maintenance, and repair of the unit.

The components of the outdoor unit must be

reachable and removable under safe conditions for

people and the unit.

WARNING

• Should adopt bar type louver. Don’t use a type of rain

resistance louver.

[Bar type louver] [Rain resistance louver]

• Louver specifications.

– Angle criteria : less than 20°

– Opening ratio criteria : greater than 80%

10

Installation Procedure

English

Installation Procedure

Moving the outdoor unit with wire rope

1 Before carrying the outdoor unit, fasten two wire

ropes of 8 m or longer, as shown in the figure.

2 To prevent damages or scratches effectively, insert

a piece of cloth between the outdoor unit and the

ropes.

3 Move the outdoor unit.

Wire rope

Plate protection

cloth

Step 2 Fixing the outdoor unit in place

Install the outdoor unit on a rigid and stable base to

prevent disturbance from any noise caused by vibration.

When installing the unit at a height or in a location

exposed to strong winds, fix the unit securely to a

support (i.e., a wall or a ground).

Fix the outdoor unit with anchor bolts. Make sure that

the anchor bolts are 20 mm or higher from the base

surface.

(Unit : mm)

Anchor bolt hole

CAUTION

• Install a drain outlet at the lowest end around the

base for outdoor unit drainage

• When installing the outdoor unit on the roof,

waterproof the unit and check the ceiling strength.

• Make sure that the wall can support the weights of

the rack and the outdoor unit.

• Install the rack close to the column as much as

possible.

Optional: Fixing the outdoor unit to a wall with

a rack

Soft rubber designed to cut off vibration from

rack to wall. (not supplied with product)

Designed to cut off residual vibration from

outdoor unit to rack. (not supplied with product)

Anchor bolt

Base surface

20 mm

• Install a proper grommet in order to reduce noise and

residual vibration transferred by the outdoor unit

towards the wall.

CAUTION

• When installing an air guide duct, be sure to check

the following:

– The screws do not damage the copper pipe.

– The air guide duct is fixed firmly on the guard fan.

11English

Installation Procedure

Step 3 Connecting the power cables,

communication cable, and controllers

You must connect the following three electrical cables to

the outdoor unit:

• The main power cable between the auxiliary circuit

breaker and the outdoor unit.

• The outdoor-to-indoor power cable between the

outdoor unit and the indoor unit.

• The communication cable between the outdoor unit

and the indoor unit.

CAUTION

• During installation, make first the refrigerant

connections and then the electrical connections. If

the unit is uninstalled, first disconnect the electrical

cables and then the refrigerant connections.

• Connect the air conditioner to the earthing system

before making the electrical connections.

NOTE

• Especially, if your outdoor unit is the one designed

for Russian and European markets, consult the supply

authority, if necessary, to estimate and reduce the

supply system impedance before installation.

Air conditioning system examples

When using earth leakage circuit breaker (ELCB) for a

single phase

MCCB

1

ELB

Main power

cable

Communication cable

Outdoor-to-indoor power cable

Earthing

Outdoor Unit

OR

Indoor Unit

ELCB

1

When using earth leakage circuit breaker (ELCB) for a

3-phase, 4-wire system (3P4W)

ELB

Main power

cable

Communication cable

Outdoor-to-indoor power cable

Earthing

Outdoor Unit

OR

Indoor Unit

MCCB

3

ELCB

3

CAUTION

• If the outdoor unit is installed in a location vulnerable

to an electric leak or submergence, make sure to

install an ELCB.

• For the product that uses the R-32 refrigerant, be

cautious not to generate a spark by keeping the

following requirements:

– Do not remove the fuses with power on.

– Do not disconnect the power plug from the wall

outlet with power on.

– It is recommended to locate the outlet in a high

position. Place the cords so that they are not

tangled.

12

Installation Procedure

English

Installation Procedure

Connecting the main power cable

When using ELB for 1 phase and 3 phase

1(L) 2(N) L1(R) L2(S) L3(T) N

F1 F2

1(L) 2(N) L N

F1 F2

MCCB

ELB

Power supply

Electrical

component box

The appearance of the unit may be

different from the picture depending

on the model.

Indoor Unit

1-phase

3-phase

Main power

cable

Communication cable

Communication

cable

3-phase 4-wire

main power cable

(AC 380V)

Outdoor-to-

indoor power

cable

Outdoor-to-

indoor power

cable

Cable tie

CAUTION

• You should connect the power cable into the power cable terminal and fasten it with a clamp.

• The unbalanced power must be maintained within 2% of supply rating.

If the power is unbalanced greatly, it may shorten the life of the condenser. If the unbalanced power is

exceeded over 4% of supply rating, the indoor unit is protected, stopped and the error mode indicates.

• To protect the product from water and possible shock, you should keep the power cable and the connection cord of

the indoor and outdoor units within ducts. (with appropriate IP rating and material selection for your application)

• Ensure that main supply connection is made through a switch that disconnects all poles, with contact gap of a least 3 mm.

• Devices disconnected from the power supply should be completely disconnected in the condition of overvoltage category.

• Keep distances of 50 mm or more between power cable and communication cable.

13English

Installation Procedure

Main power terminal block specifications

• 1-phase terminal block specifications

(Unit: mm)

AC100/120/140RXADKG

1(L) 2(N)

F1 F2

LN

16.3 12 11.4

10.1

• 3-phase terminal block specifications

(Unit: mm)

AC100/120/140RXADNG

1(L) 2(N) L1(R) L2(S) L3(T) N

9.8 14.2 11.4

F1 F2

10.1

Main power cable specifications

The power cable is not supplied with air conditioner.

• Select the power supply cable in accordance with relevant local and national regulations.

• Wire size must comply with the applicable local and national code.

• Specifications for local wiring power cord and branch wiring are in compliance with local cord.

Single phase

Model Outdoor unit Input current (A) Power supply

Indoor unit Outdoor unit Hz

Voltage range (V) Outdoor unit

Indoor unit Total MCA (A) MFA (A)

Rated Min. Max. Cooling Heating

AC100RN4DKG

AC100RXADKG

50 220 to 240 198 264

24.0 24.0

1.0 25.0 25.0 30.0

AC100RN4PKG

1.5 25.5 25.5 30.0

AC100RNMDKG

2.5 26.5 26.5 30.0

AC100RNCDKG

2.5 26.5 26.5 30.0

AC100RNTDKG

1.6 25.6 25.6 30.0

AC120RN4DKG

AC120RXADKG

1.0 25.0 25.0 30.0

AC120RN4PKG

1.5 25.5 25.5 30.0

AC120RNMDKG

2.5 26.5 26.5 30.0

AC120RNCDKG

2.5 26.5 26.5 30.0

AC140RN4DKG

AC140RXADKG 32.0 32.0

1.0 33.0 33.0 40.0

AC140RN4PKG

1.5 33.5 33.5 40.0

AC140RNMDKG

2.5 34.5 34.5 40.0

AC140RNCDKG

2.5 34.5 34.5 40.0

14

Installation Procedure

English

Installation Procedure

3-phase

Model Outdoor unit Input current (A) Power supply

Indoor unit Outdoor unit Hz

Voltage range (V) Outdoor unit

Indoor unit Total MCA (A) MFA (A)

Rated Min. Max. Cooling Heating

AC100RN4DKG

AC100RXADNG

50 380 to 415 342 456.5 16.1 16.1

1.0 17.1 17.1 17.1

AC100RN4PKG

1.5 17.6 17.6 17.6

AC100RNMDKG

2.5 18.6 18.6 18.6

AC100RNCDKG

2.5 18.6 18.6 18.6

AC100RNTDKG

1.6 17.7 17.7 17.7

AC120RN4DKG

AC120RXADNG

1.0 17.1 17.1 17.1

AC120RN4PKG

1.5 17.6 17.6 17.6

AC120RNMDKG

2.5 18.6 18.6 18.6

AC120RNCDKG

2.5 18.6 18.6 18.6

AC140RN4DKG

AC140RXADNG

1.0 17.1 17.1 17.1

AC140RN4PKG

1.5 17.6 17.6 17.6

AC140RNMDKG

2.5 18.6 18.6 18.6

AC140RNCDKG

2.5 18.6 18.6 18.6

NOTE

1 Voltage range

• Units are suitable for use on electrical systems

where voltage supplied to unit terminal is not

below or above listed range limits.

2 Maximum allowable voltage variation between

phases is 2%.

3 Wire size & type must comply with the applicable

local and national code.

• Wire size: Based on the value of MCA.

• Wire type: 60245 IEC57(IEC) or H05RN-

F(CENELEC) grade or more.

4 MFA is used to select the circuit breaker and the

ground fault circuit interrupter (earth leakage circuit

breaker).

5 MCA represents maximum input current.

• MFA represents capacity which may accept MCA

• Abbreviations

MCA: Min. Circuit Amps. (A)

MFA: Max. Fuse Amps. (A)

6 This equipment complies with IEC 61000-3-12

provided that the short-circuit power Ssc is greater

than or equal to Ssc (*2) at the interface point

between the user’s supply and the public system.

It is the responsibility of the installer or user of

the equipment to ensure, by consultation with the

distribution network operator if necessary, that the

equipment is connected only to a supply with a short-

circuit power Ssc greater than or equal to Ssc(*2).

Model Ssc[MVA]

AC100RXADKG 1.4

AC100RXADNG 2.5

AC120RXADKG 1.9

AC120RXADNG 2.7

AC140RXADKG 1.9

AC140RXADNG 2.5

15English

Installation Procedure

Silence mode controller wiring diagram

Outdoor unit

ASSY Control out

Non-voltage contact

Connecting the outdoor-to-indoor power cable

and the communication cable

1-phase

LN

F1 F2

1(L) 2(N) L N

F1 F2

Outdoor-to-indoor

power cable

For connecting the power and

communication cables

Main power cable Communication cable

Cable tie

Indoor Unit

Outdoor Unit

3-phase

LN

F1 F2

1(L) 2(N) L1(R) L2(S) L3(T) N

F1 F2

Indoor Unit

Outdoor-to-indoor

power cable

3-phase 4-wire main

power cable (AC 380V)

Communication

cable

Cable tie

Outdoor Unit

NOTE

• Lay the electrical wiring so that the front cover does

not rise up when doing wiring work and attach the

front cover securely.

• Ground wire for the indoor unit and outdoor unit

connection cable must be clamped to a soft copper

tin-plated eyelet terminal with M4 screw hole(NOT

SUPPLIED WITH UNIT ACCESSORIES).

16

Installation Procedure

English

Installation Procedure

Outdoor-to-indoor power terminal specifications

• Connect the cables to the terminal board using the compressed ring terminal.

• Cover a solderless ring terminal and a connector part of the power cable and then connect it.

Silver solder

Norminal

dimensions

for cable

(mm²)

Norminal

dimensions

for screw

(mm)

BDd1EFLd2t

Standard

dimension

(mm)

Allowance

(mm)

Standard

dimension

(mm)

Allowance

(mm)

Standard

dimension

(mm)

Allowance

(mm)

Min.

(mm)

Min.

(mm)

Max.

(mm)

Standard

dimension

(mm)

Allowance

(mm)

Min.

(mm)

4/6

4 9.5

±0.2 5.6

+0.3

-0.2

3.4 ±0.2 6

5 20 4.3

+0.2

0

0.9

8 15 9 28.5 8.4

+0.4

0

10 8 15 ±0.2 7.1

+0.3

-0.2

4.5 ±0.2 7.9 9 30 8.4

+0.4

0

1.15

16 8 16 ±0.2 9

+0.3

-0.2

5.8 ±0.2 9.5 13 33 8.4

+0.4

0

1.45

25

812

±0.3 11.5

+0.5

-0.2

7.7 ±0.2 11

15

34

8.4

+0.4

0

1.7

8 16.5 13 8.4

35

816

±0.3 13.3

+0.5

-0.2

9.4 ±0.2 12.5

13 38 8.4

+0.4

0

1.8

8 22 13 43 8.4

50 8 22 ±0.3 13.5

+0.5

-0.2

11.4 ±0.3 17.5 14 50 8.4

+ 0.4

0

1.8

70 8 24 ±0.4 17.5

+0.5

-0.4

13.3 ±0.4 18.5 20 51 8.4

+ 0.4

0

2.0

• Connect the rated cables only.

• Connect using a driver which is able to apply the

rated torque to the screws.

• If the terminal is loose, fire may occur caused by arc.

If the terminal is connected too firmly, the terminal

may be damaged.

Tightening torque (N⋅m)

M4 0.8 to 1.2

M5 2.0 to 3.0

• 1 N⋅m = 10 kgf⋅cm

CAUTION

• When connecting cables, you can connect the cables

to the electrical part or connect them through the

holes below depending on the spot.

• Connect the communication cable between the

indoor and outdoor units through a conduit to protect

against external forces, and feed the conduit through

the wall together with refrigerant piping.

• Remove all burrs at the edge of the knock-out hole

and secure the cable to the outdoor knock-out using

lining and bushing with an electrical insulation such

as rubber and so on.

• Must keep the cable in a protection tube.

• Keep distances of 50mm or more between power

cable and communication cable.

• When the cables are connected through the hole,

remove the Plate bottom.

17English

Installation Procedure

Outdoor-to-indoor power and communication

cables specifications

Indoor power supply

Power supply Max/Min (V) Indoor power cable

1ø, 220-240V,

50 Hz

±10% 1.5 mm²

Ĺ

, 3 wires

Communication cable

0.75 to 1.5 mm², 2 wires

• Power supply cords of parts of appliances for

outdoor use shall not be lighter than polychloroprene

sheathed flexible cord. (Code designation IEC:60245

IEC 57 / CENELEC: H05RN-F or IEC:60245 IEC 66 /

CENELEC: H07RN-F)

• When installing the indoor unit in a computer room

or net work room, use the double shielded (tape

aluminium / polyester braid + copper ) cable of

FROHH2R type.

Step 4 Optional: Extending the power

cable

1 Prepare the following tools.

Tools Spec Shape

Crimping pliers MH-14

Connection sleeve

(mm)

20xØ6.5

(HxOD)

Insulation tape

Width 19

mm

Contraction tube

(mm)

70xØ8.0

(LxOD)

2 As shown in the figure, peel off the shields from the

rubber and wire of the power cable.

• Peel off 20 mm of cable shields from the pre-

installed tube.

Power cable

(Unit: mm)

20 20 20

60

120

180

120

60

20 20 20

Pre-installe

d tube for

the power

cable

CAUTION

• For information about the power cable specifications

for indoor and outdoor units, refer to the installation

manual.

• After peeling off cable wires from the pre-installed

tube, insert a contraction tube.

18

Installation Procedure

English

Installation Procedure

3 Insert both sides of core wire of the power cable into

the connection sleeve.

• Method 1: Push the core wire into the sleeve from

both sides.

• Method 2: Twist the wire cores together and push

it into the sleeve.

Connection sleeve Connection sleeve

Method 1 Method 2

CAUTION

• If cable wires are connected without using connecting

sleeves, their contact area becomes reduced, or

corrosion develops on the outer surfaces of the wires

(copper wires) over a long time. This may cause an

increase of resistance (reduction of passing current)

and consequently may result in a fire.

4 Using a crimping tool, compress the two points and

flip it over and compress another two points in the

same location.

• The compression dimension should be 8.0.

Compression

dimension

• After compressing it, pull both sides of the wire to

make sure it is firmly pressed.

Compress it 4 times.

5 mm

Compress it 4 times.

5 mm

Method 1 Method 2

5 Wrap it with the insulation tape twice or more and

position your contraction tube in the middle of the

insulation tape.

Method 1 Method 2

Insulation tape

40 mm

35 mm

Insulation tape

6 Apply heat to the contraction tube to contract it.

Method 1 Method 2

Contraction tube

7 After tube contraction work is completed, wrap it with

the insulation tape to finish.

Three or more layers of insulation are required.

Method 1 Method 2

IInsulation tape

CAUTION

• Make sure that the connection parts are not exposed

to outside.

• Be sure to use insulation tape and a contraction tube

made of approved reinforced insulating materials that

have the same level of withstand voltage with the

power cable. (Comply with the local regulations on

extensions.)

WARNING

• In case of extending the electric wire, please DO NOT

use a round-shaped Pressing socket.

– Incomplete wire connections can cause electric

shock or a fire.

19English

Installation Procedure

Step 5 Connecting the refrigerant pipe

Items

Maximum allowable length

Single Installation DPM Installation

Applicable outdoor unit models

AC100RXAD*G

AC120RXAD*G

AC140RXAD*G

AC100RXAD*G

AC120RXAD*G

AC140RXAD*G

Total pipe length (L1+…+Ln+1+a+b) - - 50 m 75 m

Main pipe (L1) 50 m 75 m 30 m 50 m

Max. distance among indoor units (D) - - 10 m 10 m

Max. length after branch - - 15 m 15 m

Max. height difference between

outdoor and indoor units (h1)

30 m 30 m 30 m 30 m

Max. height difference among

indoor units(h2)

- - 0.5 m 0.5 m

Max Pipe length difference among

indoor units after branch

[L2-L3 or L2-L4 or L2-L5 or a-b or

(a+L2)-(b+L4) or (a+L3)-(b+L5)]

- - 5 m 5 m

• "n" means the number of indoor unit connection of DPM.

indoor

outdoor

indoor

outdoor

L

1

L

1

L

2

L

2

D

h

2

h

2

L

3

L

3

L

4

L

4

L

5

L

1

a

b

D

L

1

L

2

L

3

h

1

h

2

h

1

h

1

h

1

n=1

n=2

n=3

n=4

• Use a joint kit that is only for DPM.

• Temper grade and minimum thickness of the refrigerant pipe

Outer diameter [mm] Minimum thickness [mm] Temper grade

ø6.35 0.7

C1220T-O

ø9.52 0.7

ø12.70 0.8

ø15.88 1.0

ø15.88 0.8

C1220T-1/2H OR C1220T-Hø19.05 0.9

ø22.23 0.9

20

Installation Procedure

English

Installation Procedure

CAUTION

• Be sure to use C1220T-1/2H (Semi-hard) pipe for

more than Ø19.05 mm. If you use C1220T-O (Soft)

pipe for Ø19.05 mm, the pipe may be broken, which

can result in an injury.

Make at least one round:

It will reduce noise and vibration

• The appearance of the unit may be different from the

diagram depending on the model.

CAUTION

• After connecting the pipes with knock-out treatment,

plug the space around the pipes.

• After connecting the pipes, proceed exactly as

directed in the guide to prevent interference with the

internal parts.

• Tighten the nuts to the specified torques. If

overtightened, the nuts could be broken so

refrigerant may leak.

• Protect or enclose refrigerant tubing to avoid

mechanical damage.

Step 6 Optional: Cutting and aring the

pipes

1 Make sure that you have the required tools available.

(pipe cutter, reamer, flaring tool, and pipe holder)

2 If you wish to shorten the pipes, cut it with a pipe

cutter, taking care to ensure that the cut edge remains

at a 90° angle with the side of the pipe. Refer to

the illustrations below for examples of edges cut

correctly and incorrectly.

Pipe cutter

Pipe

90°

Oblique

Rough

Burr

90

3 To prevent any gas from leaking out, remove all burrs

at the cut edge of the pipe, using a reamer.

4 Slide a flare nut on to the pipe and modify the flare.

D

A

D

45° ±2°

90° ±2°

Pipe

Flare

R 0.4 to 0.8 mm

L

Outer diameter (D) Depth (A) Flare dimension (L)

ø6.35 mm 1.3mm 8.7 to 9.1 mm

ø9.52 mm 1.8mm 12.8 to 13.2 mm

ø12.70 mm 2.0mm 16.2 to 16.6 mm

ø15.88 mm 2.2mm 19.3 to 19.7 mm

ø19.05 mm 2.2mm 23.6 to 24.0 mm

Pagina se încarcă ...

Samsung AC120RXADNG/EU Manual de utilizare

Samsung AC120RXADNG/EU Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente