Samsung AC140KXADGH/EU Manualul utilizatorului

Marca: Samsung

Model: AC140KXADGH/EU

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

Air conditgioner

User manual/Installation manual

AR✴✴HVSD✴✴

• Thank you for purchasing this Samsung air conditioner.

• Before operating this unit, please read this user manual carefully and retain it for future

reference.

Air conditioner

Installation manual

AC✴✴✴KNPDEH/AC✴✴✴KXAD✴H

• Thank you for purchasing this Samsung air conditioner.

• Before operating this unit, please read this user manual carefully and retain it for future

reference.

PAC_IM_ENG.indd 1 2016-06-23 오전 11:51:10

Contents

English

Contents

Safety Information

Safety Information 3

General information

Installing the unit

Power supply line, fuse or circuit breaker

Installation Procedure 6

Step 1 Choosing the installation location

Step 2 Unpacking

Step 3 Checking and preparing accessories

Step 4 Drilling a hole through a wall

Step 5 Taping the pipes, cables, and drain hose

Step 6 Connecting the refrigerant pipes

Step 7 Optional: Cutting and flaring the pipes

Step 8 Connecting the power and communication cables

Step 9 Optional: Extending the power cable

Step 10 Checking the earthing

Step 11 Performing gas leakage test

Step 12 Evacuating the air

Step 13 Charging the refrigerant

Step 14 Fixing and insulating the connection part for refrigerant pipes

Step 15 Installing and connecting the drain hose

Step 16 Performing drainage test

Step 17 Checking the earthing

Step 18 Performing the final check and trial operation

Appendix 25

COMMISSION DELEGATED REGULATION (EU) No 626/2011

PRODUCT FICHE (ENERGY LABELLING OF AIR CONDITIONERS)

ii)

Troubleshooting

For information on Samsung’s environmental commitments and product specific regulatory obligations e.g. REACH

visit: samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html

PAC_IM_ENG.indd 2 2016-06-23 오전 11:51:10

3English

Safety Information

Carefully follow the precautions listed as below because

they are essential to guarantee the safety of SAMSUNG

product.

WARNING

∙ Always disconnect the air conditioner from the power

supply before servicing it or accessing its internal

components.

∙ Verify that installation and testing operations are

performed by qualified personnel.

∙ Verify that the air conditioner is not installed in an

easily accessible area.

General information

∙ Carefully read the content of this manual before

installing the air conditioner and store the manual in

a safe place in order to be able to use it as reference

after installation.

∙ For maximum safety, installers should always

carefully read the following warnings.

∙ Store the manual in a safe location and remember to

hand it over to the new owner if the air conditioner is

sold or transferred.

∙ This manual explains how to install an indoor unit

with a split system with two SAMSUNG units. The use

of other types of units with different control systems

may damage the units and invalidate the warranty.

The manufacturer shall not be responsible for

damages arising from the use of non compliant units.

∙ The manufacturer shall not be responsible for

damage originating from unauthorized changes or

the improper connection of electric and hydraulic

lines. Failure to comply with these instructions or

to comply with the requirements set forth in the

“Operating limits” table, included in the manual, shall

immediately invalidate the warranty.

∙ The air conditioner should be used only for the

applications for which it has been designed: the

indoor unit is not suitable to be installed in areas

used for laundry.

∙ Do not use the units if damaged. If problems occur,

switch the unit off and disconnect it from the power

supply.

∙ In order to prevent electric shocks, fires or injuries,

always stop the unit, disable the protection switch

and contact SAMSUNG’s technical support if the unit

produces smoke, if the power cable is hot or damaged

or if the unit is very noisy.

∙ Always remember to inspect the unit, electric

connections, refrigerant tubes and protections

regularly. These operations should be performed by

qualified personnel only.

∙ The unit contains moving parts, which should always

be kept out of the reach of children.

∙ Do not attempt to repair, move, alter or reinstall the

unit. If performed by unauthorized personnel, these

operations may cause electric shocks or fires.

∙ Do not place containers with liquids or other objects

on the unit.

∙ All the materials used for the manufacture and

packaging of the air conditioner are recyclable.

∙ The packing material and exhaust batteries of the

remote control (optional) must be disposed of in

accordance with current laws.

∙ The air conditioner contains a refrigerant that has

to be disposed of as special waste. At the end of its

life cycle, the air conditioner must be disposed of in

authorized centers or returned to the retailer so that

it can be disposed of correctly and safely.

∙ This product has been determined to be in compliance

with the Low Voltage Directive (2006/95/EC), and the

Electromagnetic Compatibility Directive (2004/108/

EC) and the Machinery Directive (2006/42/EC) of the

European Union.

∙ This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, without supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

∙ For use in Europe: This appliance can be used by

children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have

been given supervision or instruction concerning use

of the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be

made by children without supervision.

Safety Information

PAC_IM_ENG.indd 3 2016-06-23 오전 11:51:10

Safety Information

English

Safety Information

Installing the unit

IMPORTANT: When installing the unit, always remember

to connect first the refrigerant tubes, then the electrical

lines. Always disassemble the electric lines before the

refrigerant tubes.

∙ Upon receipt, inspect the product to verify that

it has not been damaged during transport. If the

product appears damaged, DO NOT INSTALL it and

immediately report the damage to the carrier or

retailer (if the installer or the authorized technician

has collected the material from the retailer).

∙ After completing the installation, always carry out a

functional test and provide the instructions on how to

operate the air conditioner to the user.

∙ Do not use the air conditioner in environments with

hazardous substances or close to equipment that

release free flames to avoid the occurrence of fires,

explosions or injuries.

∙ Our units must be installed in compliance with

the spaces indicated in the manual to ensure

either accessibility from both sides or ability to

perform routine maintenance and repairs. The units’

components must be accessible and that can be

disassembled in conditions of complete safety either

for people or things. For this reason, where it is

not observed as indicated into the manual, the cost

necessary to reach and repair the unit (in safety, as

required by current regulations in force) with slings,

trucks, scaffolding or any other means of elevation

won’t be considered in-warranty and charged to end

user.

Power supply line, fuse or circuit

breaker

∙ For this reason, when provisions of the installation

manual are not complied with, the cost required to

access and repair the units (in SAFETY CONDITIONS,

as set out in prevailing regulations) with harnesses,

ladders, scaffolding or any other elevation system

will NOT be considered part of the warranty and will

be charged to the end customer.

∙ Always make sure that the power supply is compliant

with current safety standards. Always install the air

conditioner in compliance with current local safety

standards.

∙ Always verify that a suitable grounding connection is

available.

∙ Verify that the voltage and frequency of the power

supply comply with the specifications and that the

installed power is sufficient to ensure the operation

of any other domestic appliance connected to the

same electric lines.

∙ Always verify that the cut-off and protection switches

are suitably dimensioned.

∙ Verify that the air conditioner is connected to the

power supply in accordance with the instructions

provided in the wiring diagram included in the

manual.

∙ Always verify that electric connections (cable entry,

section of leads, protections…) are compliant with

the electric specifications and with the instructions

provided in the wiring scheme. Always verify that all

connections comply with the standards applicable to

the installation of air conditioners.

CAUTION

∙ Make sure that you earth the cables.

– Do not connect the earth wire to the gas pipe,

water pipe, lighting rod or telephone wire. If

earthing is not complete, electric shock or fire may

occur.

∙ Install the circuit breaker.

– If the circuit breaker is not installed, electric shock

or fire may occur.

∙ Make sure that the condensed water dripping from

the drain hose runs out properly and safely.

∙ Install the power cable and communication cable of

the indoor and outdoor unit at least 1m away from

the electric appliance.

∙ Install the indoor unit away from lighting apparatus

using the ballast.

– If you use the wireless remote control, reception

error may occur due to the ballast of the lighting

apparatus.

PAC_IM_ENG.indd 4 2016-06-23 오전 11:51:10

5English

Safety Information

∙ Do not install the air conditioner in following places.

– Place where there is mineral oil or arsenic acid.

Resin parts flame and the accessories may drop or

water may leak. The capacity of the heat exchanger

may reduce or the air conditioner may be out of

order.

– The place where corrosive gas such as sulfurous

acid gas generates from the vent pipe or air outlet.

The copper pipe or connection pipe may corrode

and refrigerant may leak.

– The place where there is a machine that generates

electromagnetic waves. The air conditioner may not

operate normally due to control system.

– The place where there is a danger of existing

combustible gas, carbon fiber or flammable dust.

The place where thinner or gasoline is handled. Gas

may leak and it may cause fire.

∙ Be sure not to perform power cable modification,

midway wiring, and multiple wire connection.

– It may cause electric shock or fire due to poor

connection or insulation and current limit override.

– When midway wiring is required due to power line

damage, refer to "Step 9 Optional: Extending the

power cable" in the installation manual.

PAC_IM_ENG.indd 5 2016-06-23 오전 11:51:10

6 English

Installation Procedure

Step 1 Choosing the installation

location

Determine the installation location considering the

following conditions and obtain the user approval.

Indoor unit

∙ Install the unit where the pipes and cables can be

easily connected to the outdoor unit.

∙ Install the unit where there are no obstacles against

the wind around the air intake and air outlet.

∙ Install the unit on a flat and stable surface that can

hold the unit’s weight. Otherwise, the unit may

generate noise and vibrations.

∙ Do not install the unit near highly frequented doors

and passages.

∙ Do not install the unit in a location exposed to direct

sunlight.

Top view Side view

More than 60cm

More than 100cm

More than 50cm

Air intake

Air outlet

Outdoor unit

∙ Install the unit where it will not experience oil

leakages, salt collection, gas exposure, or sulfide gas

risk, and keep it and safe from other dangers.

∙ Install the unit where does not disturb your neighbors

as they may be affected by the noise or airflow

coming from the unit.

∙ Install the unit where no rainwater can collect on or

near it.

∙ Install the unit in a well-ventilated location away

from direct sunlight or strong winds.

∙ Install the unit where the pipes and cables can be

easily connected to the indoor unit.

∙ Maintain sufficient space for repairs and service.

∙ Make sure that condensed water dripping from the

drain hose is directed away safely.

∙ If there is any unavoidable reason to install the unit

at such a place, take the following measures:

– When installing the unit at a roadside concentrated

with buildings, install it parallel to the road.

– Install the unit so that the air outlet faces the wall

such as rooftop that may be subjected to strong

wind.

Strong wind

Rooftop

∙ When installing the outdoor unit near the seashore,

make sure that it is not directly exposed to sea

breeze. If you cannot find an adequate place, a

protection wall should be constructed.

– Install the outdoor unit at a place (such as near

a building) where it can be protected from sea

breeze. Failure to do so may cause damage to the

outdoor unit.

Outdoor UnitOutdoor Unit

Sea Sea

Sea breeze Sea breeze

∙ If you cannot avoid a place near the seashore,

construct a protection wall around the outdoor unit.

Outdoor Unit

Protection wall

Sea

Sea breeze

Installation Procedure

PAC_IM_ENG.indd 6 2016-06-23 오전 11:51:11

7English

Installation Procedure

∙ Construct a protection wall made of solid material

such as concrete to block sea breeze. Make sure that

its height and width are 1.5 times greater than the

size of the outdoor unit. In addition, secure a space

larger than 600 mm between the protection wall and

the outdoor unit for exhausted air to ventilate.

∙ Install the unit at a place where water can drain

smoothly.

∙ If you have any difficulty in finding an installation

location, contact your manufacturer.

∙ Be sure to clean sea water and dust on the heat

exchanger of the outdoor unit and apply a corrosion

inhibitor on it (at least once in a year).

Outdoor unit installation request

∙ The suggested space is based on the outdoor

temperature of 35°C while in operation. If the outdoor

temperature is higher than 35°C, secure more space.

∙ Be sure to secure sufficient clearance for a person

and air flow passage.

∙ See the clearances and dimensions in Minimum

clearances for the outdoor unit (page 7) when

installing the outdoor unit.

∙ If you install multiple outdoor units in the same place,

be sure to secure enough space for ventilation and

free airflow.

∙ If the space for ventilation is insufficient, the air

conditioner may not perform well as designed.

Minimum clearances for the outdoor unit

When installing 1 outdoor unit

(Unit: mm)

300 or more

1500 or

300 or

600 or

300 or

2000 or

1500 or more

300 or

600 or more

300 or more

1500 or more

When installing more than 1 outdoor unit

(Unit: mm)

1500 or

600 or

3000 or

300 or

600 or

300 or

1500 or

600 or

300 or more

1500 or more

300 or

500 or

300 or

PAC_IM_ENG.indd 7 2016-06-23 오전 11:51:11

Installation Procedure

English

Installation Procedure

WARNING

∙ After installing the outdoor unit, apply rust inhibitor

on the internal pipes and heat exchanger.

– Airborne corrosive gas such as sulfur compounds,

hydrogen sulfide, and ammonia, or salty dust may

cause pipe corrosion. This corrosion may result in

refrigerant leakage.

– Inspect the outdoor unit at least once a year and

re-apply the rust inhibitor where it is damaged or

worn out.

∙ When applying rust inhibitor, be sure to follow the

instructions below:

– Turn off the power before spraying the rust

inhibitor.

– Wear protective goggles and a mask in advance.

– Clean the dusty surface with clean fabric or paper

before spraying the inhibitor.

– Make sure that wind is blowing from behind the

worker.

– Do not spray on the PCB panel and electric parts.

CAUTION

∙ Install the indoor unit away from any interference,

such as radios, computers, and stereo devices, and

also select the place where the electrical wiring work

is possible.

– Keep the unit at least 3 m away from electronic

devices that generate electromagnetic waves, and

install a protection tube for the main power cable

and communication cable.

– Make sure that there is no device that can generate

electromagnetic waves. Otherwise, a malfunction

of the control system may occur. For example, the

indoor unit remote control sensor may not properly

receive signals near fluorescent lamps because of

interference.

∙ Be sure to install the outdoor unit in a safe place

where it is not affected by snowfall. The frame should

be installed in a place where the air inlet and heat

exchanger of the unit are not buried under snow.

∙ A ventilation system is required when the outdoor

unit is installed in a closed space or room, even

though R-410A is not poisonous or flammable.

∙ Install the railing around the outdoor unit to prevent

falling when installed at a high place.

∙ Avoid installation near exhaust pipes and ventilating

openings exposed to corrosive gas, sulfur oxide,

ammonia, or sulfur gas herbicide. Installations near

these places require anticorrosive treatments. Contact

the manufacturer to avoid corrosion of copper pipes

or soldered parts.

∙ Depending on the power supply, electric noise or

unstable voltage may happen after malfunctions of

the electrical parts or the control system particularly

on ships or other places using generators.

Fixing the outdoor unit in place

Fix the outdoor unit with anchor bolts. Make sure that

the anchor bolts are 20 mm or higher from the base

surface.

(Unit: mm)

Anchor bolt hole

CAUTION

∙ Install a drain outlet at the lowest end around the

base for the outdoor unit drainage.

∙ When installing the outdoor unit on the roof,

waterproof the unit and check ceiling strength.

PAC_IM_ENG.indd 8 2016-06-23 오전 11:51:12

9English

Installation Procedure

Step 2 Unpacking

Unpacking the indoor unit

1 Open the indoor unit package.

2 Remove the top and middle cushions.

3 Remove the bottom cushion.

Unpacking the outdoor unit

1 Pull out the outdoor unit from the package.

2 Remove the top cushion.

3 Remove the 4 screws from the wooden pallet.

4 Remove the wooden pallet.

Step 3 Checking and preparing

accessories

The following accessories are supplied with the

air conditioner. Their type and quantity may differ

depending on the specifications.

Accessories in the indoor unit package

Fixing bracket for indoor

unit (1)

Remote control (1)

MANUAL (2)

Remote control holder

(1)

Batteries for remote

control (2)

Insulation for piping(1)

M4 X L12 screws (4) M4 X L14 screws (4)

Pipe outlet protection

rubber (1)

Insulation for drain hose

(1)

Accessories in the outdoor unit package

Drain cap (3) Drain plug out (1)

Rubber leg (4)

Step 4 Drilling a hole through a wall

1 Determine the position of a 60 to 65 mm hole

considering possible directions of the pipe bundle and

minimum distances between the hole and installation

plate.

2 Drill the hole that slopes slightly downward (15°).

Ø 60~65 mm

Outdoor

Indoor unit

PAC_IM_ENG.indd 9 2016-06-23 오전 11:51:12

Installation Procedure

English

Installation Procedure

Step 5 Taping the pipes, cables, and

drain hose

1 Wrap the refrigerant pipes with the provided

insulation. This wrapping minimises condensation.

Insulation

Refrigerant pipes

2 Wind the refrigerant pipes, power cable,

communication cable, and drain hose with vinyl tape

to make a pipe bundle.

Pipe insulator

Vinyl tape

Drain hose

Indoor/outdoor

unit

communication

cable

NOTE

∙ Be sure to insulate the pipes without gaps or cracks,

and use adhesive between the connecting parts of the

insulation to prevent moisture from entering.

∙ When bending the pipe, try to secure a large bending

radius (over 100 mm) to prevent the copper pipe

from distorting.

∙ Use the polyethylene or EPDM foam insulation with a

thickness over 7 mm.

∙ If pipes are installed in a place with humidity

over 80% (such as in a building site pit, basement,

seashore, near hot springs, or lakes), use an insulation

of a thickness over 10 mm.

∙ Make sure that the thickness of the insulation does

not get thinner on the pipe's bending area.

∙ When the insulation thickness becomes thinner, use

extra insulation to maintain thickness.

∙ When installing the pipe hanger, use extra PE- foam

insulation (over 5 mm) to make the width of the

insulation 3 times wider than the hanger. Do not use

cable ties as a pipe hanger.

Step 6 Connecting the refrigerant

pipes

Items Maximum allowable length

Outdoor unit

models

AC100KXADEH AC140KXADGH

Main pipe (L1) 50 m 75 m

Max. height

difference

between outdoor

and indoor units

(h1)

30 m 30 m

n=1

indoor

Outdoor

∙ Temper grade and minimum thickness of the

refrigerant pipe

Outer diameter

[mm]

Minimum

thickness [mm]

Temper grade

ø6.35 0.7

C1220T-O

ø9.52 0.7

ø12.70 0.8

ø15.88 1.0

ø15.88 0.8

C1220T-1/2H OR

C1220T-H

ø19.05 0.9

ø22.23 0.9

PAC_IM_ENG.indd 10 2016-06-23 오전 11:51:12

11English

Installation Procedure

1 Connect each assembly pipe to the appropriate valves

on the indoor and outdoor units and fasten the flare

nuts.

2 As depicted in the illustration below, tighten the flare

nut manually, and then apply the following torque

with a torque wrench.

Indoor unit

Liquid side

service valve

Gas side

service valve

Outdoor unit

Liquid

Gas

Pipe Flare

Outer Diameter

(D, mm)

Fastening torque

(N·m)

Depth (A, mm)

6.35 14 to 18 1.3

9.52 34 to 42 1.8

12.7 49 to 61 2

15.88 68 to 82 2.2

19.05 100 to 120 2.2

WARNING

∙ During installation, make sure that there is no gas

leakage. When collecting refrigerant, first stop the

compressor. If the refrigerant pipe is not properly

connected and compressor runs with the service

valve open, the pipe takes in air and the pressure

rises, which may cause explosion or injury.

CAUTION

∙ Be sure to use C1220T-1/2H (Semi-hard) pipe for

more than Ø19.05 mm. If you use C1220T-O (Soft)

pipe for Ø19.05 mm, the pipe may be broken, which

can result in an injury.

Make at least one round:

It will reduce noise and vibration

∙ The appearance of the unit may be different from the

diagram depending on the model.

PAC_IM_ENG.indd 11 2016-06-23 오전 11:51:13

Installation Procedure

English

Installation Procedure

Step 7 Optional: Cutting and flaring

the pipes

1 Make sure that you have the required tools; pipe

cutter, reamer, flaring tool, and pipe holder.

2 If you want to shorten the pipes, cut it with a pipe

cutter, making sure that the cut edge remains at a

90° angle to the side of the pipe. See the illustrations

below for the correct edge cut.

90°

Oblique

Rough Burr

3 To prevent gas leakage, remove all burrs at the cut

edge of the pipe with a reamer.

Pipe

Reamer

4 Slide a flare nut onto the pipe.

5 Modify the flare with a flaring tool.

Flaring tool

6 Check that the flaring has been properly made,

referring to the illustrations below.

Correct Inclined Damaged

Surface

Cracked Uneven

Thickness

Step 8 Connecting the power and

communication cables

Electrical work must be done by the certified personnel.

∙ Wiring work should be performed in compliance with

related regulations following technical specifications

and installation guide.

∙ Be sure to install an exclusive power supply. If you

use a power strip for multiple electrical connections,

there is a risk of electric shock or fire.

∙ Be sure to install a circuit breaker with a rated current

sensitivity of over 30 mA.

∙ Fasten the screws on the terminal block to be within

the rated range and so that they do not loosen.

∙ Be sure to connect the ground wire. Install the power

wire and make sure it is shorter than 50 m. If the

length of the power wire exceeds 50 m, the product

may not work properly or the wire may be damaged.

Outdoor-to-indoor power and communication

cables specifications

Indoor power supply

Power supply Max/Min (V) Indoor power cable

1Φ, 220-240V,

50 Hz

±10% 2.5 mm²

↑

, 3 wires

Communication cable

0.75 to 1.5 mm², 2 wires

NOTE

∙ For outdoor use, the power supply cords of

the appliances must not be lighter than the

polychloroprene sheathed flexible cord. (Code

designation IEC: 60245 IEC 57 / CENELEC: H05RN-F

or IEC: 60245 IEC66 / CENELEC H07RN-F)

∙ When installing the indoor unit in a computer room

or net work room, use the double shielded (tape

aluminium / polyester braid + copper ) cable of

FROHH2R type.

PAC_IM_ENG.indd 12 2016-06-23 오전 11:51:13

13English

Installation Procedure

CAUTION

∙ Use rated cables or products only, with heat

resistance over 105°C, as well as properly rated

switches or fuses in the cabinet panel.

∙ Make sure that the cables connected do not produce

sparks around the auxiliary power switch or that

they are not installed in a place subject to high

temperature. High ambient temperature decreases

allowable current.

∙ Install the auxiliary power switch in a dry place,

install the panel board or electrical component box,

and then install the circuit breaker in the panel board.

∙ When connecting the main power cable, press the

cable to the terminal for a secure connection.

∙ Select a ring terminal for use.

F E

Silver solder

Thickness of the

wire (mm

)

B (mm) d2 (mm)

2.5 Less than 9.5 More than 4.5

4 Less than 9.5 More than 4.5

6 Less than 9.5 More than 4.5

10 Less than 15 More than 8.4

Connecting the cable to the power terminal

Connect the cables to the terminal board with the ring

terminals.

NOTE

∙ Be sure to use the certified and rated cables and

firmly connect them without applying any external

force to the ring terminal.

∙ Connect with a driver and wrench that can apply the

rated torque to the screws.

∙ Connect the terminal screws in compliance with the

rated tightening torques.

∙ If the terminal is loose, a fire may occur, caused by

arcing electricity. If the terminal is connected too

firmly, the terminal may be damaged.

Screw

Tightening torque for

terminal (kgf∙cm)

M3 5 to 7.5

M3.5 8 to 12

M4 12 to 18

M5 20 to 30

M6 25 to 37.5

S T N

When connecting two cables to a ring terminal, separate the ring

terminal up or down to prevent it from getting loose. Place the thin

cable upward and the thick cable downward. Fix the power cables

with a cable tie.

Solderless ring

terminal

Cable tie

Thin cable

Thick cable

Connecting the cables

AC100KXADEH

∙ This product uses a single phase power, with 220 to 240V

supply.

∙ When connecting the outdoor-to-indoor power cables, be

sure to match the numbers (or letters) between the outdoor

and indoor units. Connect the communication cable to the

connector included in the electrical component box for each

unit. When the outdoor-to-indoor power cables are connected

incorrectly, a malfunction of the product may occur.

∙ When connecting the communication and outdoor-to-indoor

power cables, make sure these cables do not touch the

service valve on the refrigerant pipe on the gas side or the

pipes without proper insulation. Fix the outdoor-to-indoor

power cables to the insulated pipes.

∙ Be sure to comply with the wiring standards, as there may

be a risk of fire.

∙ Make sure to install the circuit breaker firmly inside the

electrical component box.

PAC_IM_ENG.indd 13 2016-06-23 오전 11:51:14

Installation Procedure

English

Installation Procedure

Entire system diagram

ELB

NFB Single

phase 220 to

240V, 50 Hz

Outdoor-to-indoor power cable

Main power cable

Outdoor unit Indoor unit

Electrical panel

Earthing

Ground wire

Communication cable

Power wiring diagram

1(L)

2(N) L N

F1 F2

Outdoor-to-indoor

power cable

Communication

cable

cable tie

power supply cable (Single

phase AC 230V, should be

purchased on-site)

Indoor and outdoor unit connection diagram

1(L)

2(N) L N

F1 F2

1(L) 2(N)

F1 F2

Outdoor unit

Indoor unit

AC140KXADGH

∙ This product uses a 3-phase 4-wire electrical system,

with 380 to 415V supply.

∙ When connecting the outdoor-to-indoor power cables,

be sure to match the numbers (or letters) between the

outdoor and indoor units. Connect the communication

cable to the connector included in the electrical

component box for each unit. When the outdoor-

to-indoor power cables are connected incorrectly, a

malfunction of the product may occur.

∙ When connecting the communication and outdoor-to-

indoor power cables, make sure these cables do not

touch the service valve on the refrigerant pipe on the

gas side or the pipes, without proper insulation. Fix the

outdoor-to-indoor power cables to the insulated pipes.

∙ Make sure to comply with the wiring standards, as

there may be a risk of fire.

∙ Make sure to install the circuit breaker firmly inside

the electrical component box.

∙ Install a 3-phase 4-wire circuit breaker.

∙ When using the power (R, S, T, N) with the NFB

(overcurrent breaker), be sure to connect the main

power cable (R, S, T, N) to the R, S, T and N terminal on

the outdoor unit.

Entire system diagram

ELB

NFB 3phase 4

wires, 380 to

415V, 50 Hz

Outdoor-to-indoor power cable

Main power cable

Outdoor unit Indoor unit

Electrical panel

Earthing

Ground wire

Communication cable

Power wiring diagram

F1 F2

1(L)

2(N)

L1(R)

L2(S)

L3(T)

Outdoor-to-indoor

power cable

Communication

cable

cable tie

power supply cable (Single

phase AC 230V, should be

purchased on-site)

Indoor and outdoor unit connection diagram

F1 F2

1(L) 2(N) F1 F2

1(L)

2(N)

L1(R)

L2(S)

L3(T)

Outdoor unit

Indoor unit

PAC_IM_ENG.indd 14 2016-06-23 오전 11:51:14

15English

Installation Procedure

Main power cable specifications

The power cable is not supplied with air conditioner.

∙ Select the power supply cable in accordance with relevant local and national regulations.

∙ Wire size must comply with the applicable local and national code.

∙ Specifications for local wiring power cord and branch wiring are in compliance with local cord.

Model Outdoor unit Input current (Amperes) Power supply

Outdoor unit Indoor unit

Rated Voltage Range

Outdoor(Down_Amp)

Indoor Total MCA MFA

Hz Volts Min

Max

Cooling Heating

AC100KXADEH

AC100KNPDEH

50 220-240 198 264 21.7 21.7 1.5 23.2 23.2 29.0

AC140KXADGH

AC140KXPDEH

50 380-415 342 456.5 14.6 14.6 16.1 16.1 16.1 16.1

NOTE

1 Voltage range

∙ Units are suitable for use on electrical systems where voltage supplied to unit terminal is not below or above

listed range limits

2 Maximum allowable voltage variation between phases is 2%.

3 Wire size & type must comply with the applicable local and national code.

∙ Wire size: Based on the value of MCA.

∙ Wire type: 60245 IEC57(IEC) or H05RN-F(CENELEC) grade or more.

4 MFA is used to select the circuit breaker and the ground fault circuit interrupter (earth leakage circuit breaker).

5 MCA represents maximum input current.

∙ MFA represents capacity which may accept MCA

∙ Abbreviations

MCA: Min. Circuit Amps. (A)

MFA: Max. Fuse Amps. (A)

6 This equipment complies with IEC 61000-3-12 provided that the short-circuit power Ssc is greater than or equal

to Ssc (*2) at the interface point between the user’s supply and the public system. It is the responsibility of the

installer or user of the equipment to ensure, by consultation with the distribution network operator if necessary,

that the equipment is connected only to a supply with a short-circuit power Ssc greater than or equal to Ssc(*2).

MODEL Ssc[MVA]

AC100KXADEH 4.03

AC140KXADGH 3.12

PAC_IM_ENG.indd 15 2016-06-23 오전 11:51:14

Installation Procedure

English

Installation Procedure

Step 9 Optional: Extending the power

cable

1 Prepare the following tools.

Tools Spec Shape

Crimping pliers MH-14

Connection sleeve

(mm)

20 x Ø6.5

(HxOD)

Insulation tape

Width 19

Contraction tube

(mm)

70 x Ø8.0

(LxOD)

2 As shown in the figure, peel off the shields from the

rubber and wire of the power cable.

∙ Peel off 20 mm of cable shields from the pre-

installed tube.

CAUTION

∙ For information about the power cable specifications

for indoor and outdoor units, refer to the installation

manual.

∙ After peeling off cable wires from the pre-installed

tube, insert a contraction tube.

Power cable

120

180

Pre-installed tube for the power cable

(Unit: mm)

3 Insert both sides of core wire of the power cable into

the connection sleeve.

∙ Method 1: Push the core wire into the sleeve from

both sides.

∙ Method 2: Twist the wire cores together and push it

into the sleeve.

Connection sleeveConnection sleeve

Method 2Method 1

4 Using a crimping tool, compress the two points and flip it

over and compress another two points in the same location.

∙ The compression dimension should be 8.0.

Compression

dimension

∙ After compressing it, pull both sides of the wire to

make sure it is firmly pressed.

Compress it 4 times. Compress it 4 times.

5 mm 5 mm

Method 1 Method 2

5 Wrap it with the insulation tape twice or more and

position your contraction tube in the middle of the

insulation tape.

Three or more layers of insulation are required.

Method 1 Method 2

Insulation tape Insulation tape

40 mm 35 mm

6 Apply heat to the contraction tube to contract it.

Contraction tube

7 After tube contraction work is completed, wrap it with

the insulation tape to finish.

Insulation tube

PAC_IM_ENG.indd 16 2016-06-23 오전 11:51:15

17English

Installation Procedure

CAUTION

∙ Make sure that the connection parts are not exposed

to outside.

∙ Be sure to use insulation tape and a contraction tube

made of approved reinforced insulating materials that

have the same level of withstand voltage with the power

cable. (Comply with the local regulations on extensions.)

WARNING

∙ In case of extending the

electric wire, DO NOT use a

round-shaped pressing socket.

– Incomplete wire connections

can cause electric shock or a fire.

Step 10 Checking the earthing

If the power distribution circuit does not have a earthing

or the earthing does not comply with specifications, an

earthing electrode must be installed. The corresponding

accessories are not supplied with the air conditioner.

1 Select an earthing electrode that complies with the

specifications given in the illustration.

2 Connect the flexible hose to the flexible hose port.

∙ In damp hard soil rather than loose sandy or gravel

soil that has a higher earthing resistance.

∙ Away from underground structures or facilities,

such as gas pipes, water pipes, telephone lines and

underground cables.

∙ At least two metres away from a lightening

conductor earthing electrode and its cable.

NOTE

∙ The earthing wire for the telephone line cannot be

used to ground the air conditioner.

50 cm

30 cm

Carbon plastic

To grounding screw

Steel core

Terminal M4

PVC-insulated

green/yellow

wireTo

3 Finish wrapping insulating tape around the rest of the

pipes leading to the outdoor unit.

4 Install a green/yellow coloured earthing wire:

∙ If the earthing wire is too short, connect an

extension lead in a mechanical way and wrap it

with insulating tape (do not bury the connection).

∙ Secure the earthing wire in position with staples.

NOTE

∙ If the earthing electrode is installed in an area with

heavy traffic, its wire must be connected securely.

5 Carefully check the installation by measuring the

earthing resistance with a earth resistance tester. If

the resistance is above the required level, drive the

electrode deeper into the ground or increase the

number of earthing electrodes.

6 Connect the earthing wire to the electrical component

box inside of the outdoor unit.

Step 11 Performing gas leakage test

Use nitrogen gas at a pressure range between 0.2 and

4.1 MPa when testing the gas leakage. If you apply

pressure at over 4.1 MPa, the refrigerant pipes may be

damaged.

Outdoor unit

Gas

Liquid

Manifold gauge

High pressure side

Low pressure side

Vacuum

pump

Nitrogen gas

PAC_IM_ENG.indd 17 2016-06-23 오전 11:51:16

Installation Procedure

English

Installation Procedure

1 Connect the charging hose of low pressure side of

manifold gauge to the packed valve having a service

port as shown at the figure.

NOTE

∙ The designs and shape are subject to change

according to the model.

2 Open the valve of the low pressure side (A) of the

manifold gauge anticlockwise.

3 Connect the manifold gauge to the nitrogen gas.

4 Apply nitrogen gas.

5 Check the change of pressure with a pressure

regulator.

6 Check the gas leakage at the connection part or

brazed part by using soap water.

7 Open the manifold gauge to discharge nitrogen.

Step 12 Evacuating the air

1 Connect the manifold gauge to a vacuum pump.

2 Purge the air from the system using the vacuum

pump for about 30 minutes.

∙ Make sure that pressure gauge shows -0.1006 Mpa

after about 30 minutes.

∙ Use a vacuum pump that is at least 140 l/min in

capacity.

∙ Make sure that vacuuming timing is longer when

the piping gets longer.

∙ Pressure will not drop even after 5 minutes of

vacuuming when there is moisture within the pipe.

In this case, apply nitrogen gas again, and then

purge the air again.

Step 13 Charging the refrigerant

Important information regulation regarding the

refrigerant used

This product contains fluorinated greenhouse gases. Do

not vent gases into the atmosphere.

CAUTION

∙ Inform user if system contains 5 tCO2e or more of

fluorinated greenhouse gases. In this case, it has to be

checked for leakage at least once every 12 months,

according to regulation n° 517/2014. This activity

has to be covered by qualified personnel only. In case

situation above (5 tCO2e or more of R-410A), installer

(or recognised person which has responsability for

final check) has to provide a maintenance book,

with all the information recorded according to

REGULATION (EU) N° 517/2014 OF THE EUROPEAN

PARLIAMENT AND OF THE COUNCIL of 16 April 2014

on certain fluorinated greenhouse gases.

Please fill in the following with indelible ink on the

refrigerant charge label supplied with the product and

on this manual.

∙

: The factory refrigerant charge of the product.

∙

: The additional refrigerant amount charged in the

field.

∙

+ : The total refrigerant charge.

Outdoor unit

Indoor unit

Unit kg tCO2e

, a

, b

+ , C

Refrigerant type GWP value

R-410A 2088

∙ GWP=Global Warming Potential

∙ Calculating tCO

2e : kg x GWP / 1000

PAC_IM_ENG.indd 18 2016-06-23 오전 11:51:16

19English

Installation Procedure

1 Measure the quantity of refrigerant depending on the

length of the liquid side pipe.

NOTE

∙ When the pipe length exceeds the standard pipe

length of 5 m, charge refrigerant according to the

increased length. Do not charge refrigerant by

assuming the quantity through the pressure gauge.

When the pipe length is shorter than the standard,

you do not need to charge refrigerant.

Model name

Refrigerant amount

Standard

(less 30m)

Additional

(over 30m)

g g/m

AC100KXADEH 3000 50

AC140KXADGH 3500 50

Outdoor unit

Ref.

(Scale)

Indoor unit

Liquid side service valve

Manifold gauge

Vacuum

pump

High pressure

side

Low pressure

side

Gas side service valve

Open the manifold gauge valve connected to the liquid

service valve and add refrigerant to reach the fixed

quantity noting the scale.

NOTE

∙ If you cannot add refrigerant when the operation of

the outdoor unit is stopped, open the gas and liquid

service valves and add remaining refrigerant by

pressing the cooling trial operation button.

∙ After charging, completely open the spindles of

the both the gas and liquid side service valves by

rotating them anti-clockwise. (Do not press them

further if the spindle hits the stopper.)

∙ Fasten the caps of the service valves for the gas and

liquid pipes including the cap nut of the charging

port.

– There may be slight refrigerant leakage when you

open the spindle with a wrench. This is not a failure

of the product.

– Use a wrench that can apply the appropriate force.

Tightening torque for body cap

(Refer to the table)

Spindle

Charging core

R-22: Thread of the screw - 7/16-2OUNF

R-410A: Thread of the screw -1/2-2OUNF

Tightening torque for charging port cap (Refer to the table)

Outer diameter

(mm)

Tightening torque

Body cap

(N•m)

Charging port cap

(N•m)

ø 6.35 20 to 25

10 to 12

ø 9.52 20 to 25

ø 12.70 25 to 30

ø 15.88 30 to 35

Over ø 19.05 35 to 40

(1 N•m = 10 kgf•cm)

NOTE

∙ Be extra cautious for the gas leakage from the 3-way

valve’s stem nuts (gas side), and from the service port

cap.

PAC_IM_ENG.indd 19 2016-06-23 오전 11:51:17

Installation Procedure

English

Installation Procedure

Pressure table for each temperature

If extra refrigerant charging is required due to gas

leakage or product relocation, see the following table.

Cooling operation

Unit: [kPa, G]

Indoor temperature (°C)

(Dry bulb /

Wet bulb)

Outdoor temperature (°C)

32/23 27/19 21/15

52 1110 900 780

35 920 750 640

21 830 690 590

7 690 540 490

-15 550 400 370

NOTE

∙ Pressure for each temperature was measured at the

gas side service valve.

Step 14 Fixing and insulating the

connection part for refrigerant pipes

CAUTION

∙ Before wrapping the connection part for refrigerant

pipes, be sure to check whether there is gas leakage

on the connection part.

1 Wrap the foam insulation around the connection

part as shown in the figure. This wrapping minimises

condensation.

High

pressure

pipe

Low

pressure

pipe

Insulator for pipe

connection part

30 mm or more

Pipe insulation

NOTE

∙ Use polyethylene foam over 5 mm thick to insulate

the connection.

2 Fasten the pipes with a pipe clamp and fix it with

screws.

WARNING

∙ Remove the middle part of the pipe outlet protection

rubber before inserting the pipe.

Pipe outlet

protection rubber

PAC_IM_ENG.indd 20 2016-06-23 오전 11:51:17

Pagina se încarcă ...

Samsung AC140KXADGH/EU Manualul utilizatorului

Marca: Samsung

Model: AC140KXADGH/EU

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Samsung AC140KXADGH/EU User guide

Samsung AC140KXADGH/EU Manualul utilizatorului

Acest manual este potrivit și pentru

Samsung AC140KXADGH/EU Manualul utilizatorului

în alte limbi

Lucrări conexe

Alte documente