Parkside PSFS 250 A1 Original Instructions Manual

IAN 270700

COMBINATION CUTTER PSFS 250 A1

COMBINATION CUTTER

Translation of the original instructions

КОМБИНИРАНА ФРЕЗА

Превод на оригиналното ръководство за експлоатация

FREZĂ COMBI

Traducerea instrucţiunilor de utilizare original

ΦΡΕΖΑ-KOMBI

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

KOMBI GLODALO

Prijevod originalnih uputa za uporabu

KOMBI-FRÄSER

Originalbetriebsanleitung

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 11

RO Traducerea instrucţiunilor de utilizare original Pagina 21

BG Превод на оригиналното ръководство за експлоатация Cтраница 31

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 41

DE / AT / CH Originalbetriebsanleitung Seite 51

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

1

PSFS 250 A1

GB

CY

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 2

General Power Tool Safety Warnings ................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 3

3. Personal safety ............................................................ 3

4. Power tool use and care .................................................... 4

5. Service .................................................................. 4

Additional safety instructions for grinders and polishers .............................. 4

Additional safety instructions for routers ........................................... 4

Original accessories/auxiliary equipment ......................................... 5

Operation .......................................................5

Switching on and oﬀ ......................................................... 5

Adjusting the rotational speed .................................................. 5

Changing tools .............................................................. 5

Fitting abrasive belts .......................................................... 6

Adjusting the working depth .................................................... 6

Milling direction on edges ..................................................... 6

Carrying out plunge cuts ...................................................... 6

Swivelling the handle ......................................................... 6

Using the parallel guide ....................................................... 6

Sawing circles .............................................................. 6

Extracting dust .............................................................. 7

Using the tool in continuous operation ............................................ 7

Maintenance and cleaning ..........................................7

Disposal .........................................................7

Warranty ........................................................8

Service ..........................................................8

Importer ........................................................8

Translation of the original Conformity Declaration ......................9

2

PSFS 250 A1

GB

CY

COMBINATION CUTTER

PSFS 250 A1

Introduction

Congratulations on the purchase of your

new appliance. You have selected a high-

quality product. The operating instructions

are part of this product. They contain important

information on safety, usage and disposal.

Before using the product, familiarise yourself with all

handling and safety guidelines. Use the product only

as described and for the range of applications speci-

ﬁed. Please also pass these operating instructions on

to any future owner.

Intended use

This appliance is intended for the processing of

materials such as wood, plastic, ﬁbreboard, wall

tiles, aluminium and sheet metal with the recom-

mended tools and accessories. It is also suitable

for grinding with a range of cylindrical grinders

and for milling with milling bits of 4.8 mm shaft

diameter. Any other usage of or modiﬁcation to the

appliance is deemed to be improper and carries

the risk of serious personal injury. The manufacturer

accepts no responsibility for damage(s) attributable

to misuse. Not for commercial use.

Features

Locking switch

Inﬁnitely variable speed control

Power cable

ON/OFF switch

Wing adjusting screw

Extraction nozzle

Baseplate

Collet chuck

Wing screw (footplate)

Tensioning nut

Spindle lock button

Ventilation slits

Swivel lock

Open-ended spanner

Circular/parallel cutting attachment

Abrasive belt mandrel

Abrasive belt

Slotting cutter (HSS)

Multipurpose milling cutter (HSS)

Adapter (extraction nozzle)

Package contents

1 combination cutter PSFS 250 A1

1 rip fence with circular cutting function

1 dust extraction adapter

1 open-ended spanner

1 multipurpose milling cutter (HSS)

1 slotting cutter (HSS)

1 abrasive belt mandrel

6 abrasive belts

1 operating instructions

Technical data

Rated power input: 250 W

Rated voltage: 230 V

~

, 50 Hz

Idle speed: n

0

10000–28000 min

-1

Collet capacity: 4.8 mm

Protection class: II /

Noise and vibration data:

Noise measurement value determined in accordance

with EN 60745. The A-rated noise level of the

power tool is typically as follows:

Sound pressure level: 75 dB (A)

Sound power level: 86 dB (A)

Uncertainty K: 3 dB

Wear hearing protection!

Weighted acceleration, typically:

Hand/arm vibration a

h

< 2.5 m/s

2

Uncertainty K = 1.5 m/s

2

3

PSFS 250 A1

GB

CY

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance

with the standardised measuring procedure

speciﬁed in EN 60745 and can be used to

make equipment comparisons. The speciﬁed

vibration emission value can also be used to

make an initial exposure estimate.

WARNING!

► The vibration level varies in accordance with

the use of the power tool and may be higher

than the value speciﬁed in these instructions

in some cases. There is a risk of underestima-

tion of the vibration load if the power tool is

used regularly in this manner. Try to keep the

vibration load as low as possible. Measures

to reduce the vibration load are, e.g. wearing

gloves and limiting the working time. Wherein

all states of operation must be included (e.g.

times when the power tool is switched oﬀ and

times where the power tool is switched on but

running without load).

General Power

Tool Safety Warnings

WARNING!

► Read all safety warnings and all instruc-

tions. Failure to follow the warnings and

instructions may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools cre-

ate sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, cookers

and refrigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cable suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate

conditions will reduce personal injuries.

4

PSFS 250 A1

GB

CY

c) Prevent unintentional starting. Ensure the switch

is in the oﬀ-position before connecting to power

source and/or battery pack, picking up or

carrying the tool. Carrying power tools with

your ﬁnger on the switch or energising power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Wear suitable clothing. Do not wear loose

clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose

clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4. Power tool use and care

a) Do not overload the power tool. Use the

correct power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch is defec-

tive. Any power tool that cannot be controlled

with the switch is dangerous and must be re-

paired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children. Do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools with care. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power

tool for operations other than those intended

could result in a hazardous situation.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only original replacement

parts. This will ensure that the safety of the

power tool is maintained.

b) If the power cord is damaged, it must be replaced

with a special cable available from the manu-

facturer or its customer service.

Additional safety instructions for

grinders and polishers

■ TOXIC DUSTS! Working with the tool can pro-

duce harmful/toxic dusts which represent a

health hazard for the person operating the

appliance and for anyone else in the vicinity.

■ Avoid sanding lead paint or other harmful

materials.

■ Materials containing asbestos may NOT be

processed. Asbestos is a known carcinogen.

Wear safety goggles and a protective

dust mask!

Additional safety instructions for

routers

■ Always hold the appliance using insulated

handle surfaces since the milling cutter can

damage its own power cord. Contact with a

live cable may also cause metal parts of the

appliance to become live and may result in an

electric shock.

5

PSFS 250 A1

GB

CY

■ Only use milling bits of the correct shaft diameter

and which are suitable for the power tool

speed.

■ Fix and secure the workpiece using clamps

or other methods to a stable base. If you hold

the workpiece in your hands or against your

body only it will remain unstable, and this can

result in loss of control.

Original accessories/auxiliary

equipment

■ Use only the accessories and additional

equipment that are speciﬁed in the operat-

ing instructions and are compatible with the

appliance.

Operation

Never use the appliance for other purposes and

only with original parts/accessories. Using attach-

ments or accessory tools other than those recom-

mended in the operating instructions can lead to

a risk of injury. Only use completely unrolled and

undamaged extension cables with a capacity of

at least 5 A.

WARNING!

► Do not use this power tool to make cuts in the

vicinity of installations or openings containing

live electrical cables or in walls in which live

electrical cables are possibly hidden. The

bit can conduct electrical current into the

tool which can result in the danger of an

electrical shock for the operator.

– Trigger the circuit breakers or remove the

fuse in order to ensure that the aﬀected

power circuit is isolated.

WARNING!

► Always hold the tool by the plastic housing

and always wear protective goggles when

working with the tool.

Switching on and oﬀ

Switching on:

♦ Press the ON/OFF switch

.

Switching oﬀ:

♦ Release the ON/OFF switch

.

Adjusting the rotational speed

♦ Turn the speed control to the right to increase

the speed.

♦ Turn the speed control

to the left to decrease

the speed.

Changing tools

NOTE

► Use only multitool milling cutter accessories

with a shaft diameter of ø 4.8 mm.

♦ Press and hold the spindle lock button

.

♦ Loosen the tensioning nut using the

open-

ended spanner by turning it anticlockwise.

♦ Change the tool.

♦ Block the spindle lock, and tighten the tensioning

nut

with the aid of the open-ended spanner

.

Bits:

The bits supplied can be used for the following

applications:

Multipurpose milling cutter (HSS)

:

Suitable for: wood, chipboard, plastic, aluminium

and sheet metal

Slotting cutter (HSS)

:

Suitable for: wood, chipboard, plastic

Abrasive belt

:

Suitable for: sanding wood

NOTE

► If you are intending to cut wall tiles and/or

process sheet metal/metal alloys, please use

appropriate accessories from your specialist

supplier.

6

PSFS 250 A1

GB

CY

Fitting abrasive belts

♦ Push the abrasive belt onto the abrasive belt

mandrel

from above . Tighten the bolt on

the abrasive belt mandrel in order to ﬁx the

abrasive belt .

♦ Fit the abrasive belts

as described in the

section "Replacing tools".

Adjusting the working depth

♦ Loosen the wing adjusting screw .

♦ Push the footplate

down to the required

working depth (around 3.2 mm more than the

material thickness for complete cutting). The

maximum recommended cut depth forward is

13 mm *(applies only to multipurpose milling

cutters (HSS) ).

♦ Retighten the wing adjusting screw

.

Milling direction on edges

Carrying out plunge cuts

♦ Introduce the bit into the workpiece at an angle

of 45°.

♦ Slowly change the angle of the bit to 90°

before starting the cut.

NOTE

► The baseplate

must be ﬂush with the material

surface.

Swivelling the handle

NOTE

► Do not rotate the handle while working.

Remove the plug from the mains socket and

ensure that the swivel lock

is engaged.

Swivelling to the horizontal position:

♦ Press the swivel lock

and hold it down.

♦ Rotate the handle anticlockwise

from the

vertical to the horizontal position until the swivel

lock engages.

Swivelling to the vertical position:

♦ Press the swivel lock

and hold it down.

♦ Rotate the handle clockwise

from the hori-

zontal to the vertical position until the swivel

lock engages.

Using the parallel guide

♦ Undo the wing screw on the baseplate ,

and push the guide rod on the circular/parallel

cutting attachment through the two recesses

on the bottom of the baseplate so that the

parallel guide is facing downwards.

♦ Align the tool at the required distance from the

workpiece edge. Tighten the wing screws

in

order to ﬁx the circular/parallel cutting attach-

ment to the baseplate .

Sawing circles

NOTE

► Depending on the required results, the guide

hole is placed either on the inside or the out-

side of the circle circumference. Inside for

a hole – outside for a disc. The radius can

be ﬁxed approximately between 5 to 16 cm.

♦ Draw a circle on the workpiece.

♦ Mark the centre of the circle and drill a hole in

it (plunge cut).

♦ Drill a guide hole on the outside of the circle

(plunge cut) (guide hole diameter 3 mm).

7

PSFS 250 A1

GB

CY

♦ Undo the wing screw on the baseplate ,

and push the guide rod on the circular/parallel

cutting attachment

through the two recesses

on the bottom of the baseplate so that the

centring point is facing downwards.

♦ Insert the centring point into the centre of the

circle.

♦ Adjust the circular/parallel cutting attachment

spacing so that the bit can be inserted into the

guide hole at the edge of the circle.

♦ Lock the baseplate

by tightening the wing

screws .

♦ Switch the tool on by pressing the ON/OFF

switch

and holding it down.

♦ Push the tool slowly forwards.

Extracting dust

■ The tool is ﬁtted with an extraction nozzle

for dust extraction.

♦ Insert the adapter into the extraction nozzle .

♦ Connect a vacuum cleaner to the adapter

.

Using the tool in continuous operation

Lock the ON/OFF switch :

♦ Press the ON/OFF switch

.

♦ Now press the locking switch

and release

the ON/OFF switch .

Unlocking the ON/OFF switch

:

♦ Press the ON/OFF switch

and release it.

Maintenance and cleaning

WARNING! RISK OF INJURY!

Always switch the appliance oﬀ

before carrying out any work on it.

The appliance is maintenance-free.

■ Always clean the appliance directly after ﬁnishing

work.

■ Use a dry cloth to clean the housing. Under

no circumstances should you use detergents,

solvents or abrasive cleaners.

■ Ensure ventilation openings are always free of

obstructions.

■ Remove any adhering swarf with a brush.

NOTE

► Spare parts which are not listed (e.g.

► carbon brushes, switches, can be ordered

using our service hotline.

Disposal

The packaging is made from environmen-

tally friendly material and can be disposed

of at your local recycling plant.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

8

PSFS 250 A1

GB

CY

Warranty

This appliance is provided with a 3-year

warranty valid from the date of purchase.

The appliance has been manufactured with

care and inspected meticulously prior to de-

livery. Please retain your receipt as proof

of purchase. In the event of a warranty claim,

please contact your Customer Service unit by

telephone. This is the only way to guarantee

free return of your goods.

The warranty only covers claims for material and

manufacturing defects, not for damage sustained

during carriage, components subject to wear and

tear or damage to fragile components such as

switches or batteries. This appliance is intended

solely for private use and not for commercial pur-

poses. The warranty shall be deemed void in cases

of misuse or improper handling, use of force and

modiﬁcations/repairs which have not been carried

out by one of our authorised Service centres. Your

statutory rights are not restricted by this warranty.

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking, but no later

than two days after the date of purchase. Repairs

carried out after expiry of the warranty period shall

be subject to charge.

Service

WARNING!

► Have the power tool repaired by the

Service Centre or a qualiﬁed electrician

and only using genuine replacement parts.

This will ensure that the safety of the appli-

ance is maintained.

► Always ensure that the plug or the power

cord is replaced only by the manufacturer of

the appliance or by an approved customer

service provider. This will ensure that the

safety of the appliance is maintained.

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: k[email protected]

IAN 270700

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: k[email protected]

IAN 270700

Hotline availability:

Monday to Friday from 8:00 a.m. to 8:00 p.m. (CET)

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

9

PSFS 250 A1

GB

CY

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH, docu-

ments oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare

that this product complies with the following stand-

ards, normative documents and EC directives:

Machine Directive

(2006/42/EC)

Electromagnetic Compatibility

(2004/108/EC)

RoHS Directive

(2011/65/EU)

Applied harmonised standards:

EN 60745-1: 2009 / A11: 2010

EN 60745-2-4: 2009 / A11: 2011

EN 60745-2-17: 2010

EN 62233: 2008

EN 55014-1: 2006 / A2: 2011

EN 55014-2: 1997 / A2: 2008

EN 61000-3-2: 2014

EN 61000-3-3: 2013

Type designation of machine:

Combination cutter PSFS 250 A1

Year of manufacture: 08 - 2015

Serial number: IAN 270700

Bochum, 22/06/2015

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context

of further development is reserved.

10

PSFS 250 A1

11

PSFS 250 A1

HR

Sadržaj

Uvod ..........................................................12

Namjenska uporaba ........................................................12

Oprema .................................................................. 12

Opseg isporuke ............................................................ 12

Tehnički podaci ............................................................ 12

Opće sigurnosne napomene za uporabu električnog alata ..............13

1. Sigurnost radnog mjesta ...................................................13

2. Električna sigurnost. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3. Sigurnost osoba ..........................................................14

4. Korištenje i rukovanje električnim alatom ....................................... 14

5. Servis ..................................................................15

Dodatne sigurnosne napomene za brusilice i polirke ...............................15

Dodatne sigurnosne napomene za površinske glodalice .............................15

Originalni pribor / dodatni uređaji .............................................15

Rukovanje ......................................................15

Uključivanje/isključivanje .....................................................16

Podešavanje broja okretaja ................................................... 16

Zamjena alata .............................................................16

Montiranje brusnih traka ..................................................... 16

Podešavanje radne dubine .................................................... 16

Smjer glodanja na rubovima ..................................................16

Izvođenje ubodnog reza .....................................................16

Zakretanje ručke ............................................................17

Uporaba paralelne vodilice ................................................... 17

Piljenje krugova ............................................................17

Usisavanje prašine ..........................................................17

Uporaba alata u trajnom pogonu .............................................. 17

Održavanje i čišćenje .............................................18

Zbrinjavanje ....................................................18

Jamstvo ........................................................18

Servis ..........................................................19

Uvoznik ........................................................19

Proizvođač: ...............................................................19

Prijevod originalne izjave o sukladnosti .............................19

Tehnički podaci ............................................................ 19

12

PSFS 250 A1

HR

KOMBI GLODALO

PSFS 250 A1

Uvod

Čestitamo na kupnji Vašeg novog uređaja.

Time ste se odlučili za visokovrijedan

proizvod. Upute za rukovanje sastavni su

dio ovog proizvoda. One sadrže važne

napomene za sigurnost, rukovanje i zbrinjavanje.

Prije uporabe uređaja upoznajte se sa svim pripada-

jućim uputama za uporabu i svim sigurnosnim napo-

menama. Proizvod koristite isključivo na opisani način

i u navedenim područjima uporabe. U slučaju pre-

daje proizvoda trećim osobama priložite i predajte

i svu dokumentaciju.

Namjenska uporaba

Ovaj je uređaj predviđen za uporabu s preporu-

čenim alatima i priborom, za obradu materijala

kao što su drvo, plastika, vlaknaste ploče, zidne

ploče, aluminijski i željezni lim. Uređaj je također

pogodan za brušenje raznim kružnim brusilicama

kao i za glodanje s nastavcima promjera osovine

4,8 mm. Svaki drugi način uporabe, te svaka izmje-

na uređaja smatra se nenamjenskom i krije visok

stupanj rizika od ozljeda. Proizvođač ne preuzima

odgovornost od štete nastale uslijed korištenja

uređaja protivno njegovoj namjeni. Uređaj nije

namijenjen za uporabu u gospodarske svrhe.

Oprema

Prekidač za blokadu

Bezstupanjski regulator broja okretaja

Mrežni kabel

Prekidač UKLJ/ISKLJ

Leptirasti vijak za podešavanje

Priključnica za usisivač

Donja ploča

Stezna čeljust

Leptirasta matica (osnovna ploča)

Stezna matica

Tipka za blokadu osovine

Ventilacijski prorezi

Blokada nagiba

Vilasti ključ

Nastavak za kružno/paralelno rezanje

Klin za zatezanje brusne trake

Brusna traka

Glodalo za utore (HSS)

Višenamjensko glodalo (HSS)

Adapter (nastavak za usisavanje)

Opseg isporuke

1 Kombi glodalo PSFS 250 A1

1 Paralelni graničnik s funkcijom za kružno rezanje

1 Adapter za usisivač za prašinu

1 Vilasti ključ

1 Višenamjensko glodalo (HSS)

1 Glodalo za utore (HSS)

1 Klin za zatezanje brusne trake

6 brusnih traka

1 Upute za uporabu

Tehnički podaci

Nazivna snaga: 250 W

Nazivni napon: 230 V

~

, 50 Hz

Broj okretaja u praznom

hodu: n

0

10000 - 28000 min

-1

Ležište za alate za: 4,8 mm

Razred zaštite: II /

Informacije o buci i vibracijama:

Vrijednost buke izmjerena sukladno EN 60745.

A - razina emisije buke električnog alata tipično

iznosi:

Razina zvučnog tlaka: 75 dB(A)

Razina jačine zvuka: 86 dB(A)

Nesigurnost K: 3 dB

Obavezno nošenje zaštite sluha!

Procijenjeno tipično ubrzanje:

Vibracija ruke/šake a

h

< 2,5 m/s

2

Nesigurnost K = 1,5 m/s

2

13

PSFS 250 A1

HR

NAPOMENA

► Razina vibracija navedena u ovim uputama

izmjerena je u skladu s EN 60745 normira-

nom procedurom mjerenja i može se koristiti

za usporedbu uređaja. Navedena razina

emisije vibracija može se koristiti i za uvodnu

procjenu izloženosti.

UPOZORENJE!

► Razina vibracija mijenja se ovisno o uporabi

električnog alata i u mnogim slučajevima

može biti iznad vrijednosti navedene u ovim

uputama. Vibracijsko opterećenje može se

i podcijeniti ako se električni alat redovito

koristi na takav način. Pokušajte opterećenje

vibracijama držati što manjim. Primjerne

mjere za smanjenje opterećenja vibracijama

su nošenje rukavica prilikom uporabe uređaja

i ograničenje radnog vremena. Pritom morate

uzeti u obzir sve sastavne dijelove ciklusa

pogona (primjerice razdoblja u kojima je

električni uređaji isključen, kao i razdoblja

u kojima je uređaj uključen ali radi bez

opterećenja).

Opće sigurnosne

napomene za uporabu

električnog alata

UPOZORENJE!

► Pročitajte sve sigurnosne napomene i

napomene za uporabu. Nepridržavanje

sigurnosnih napomena i uputa može uzroko-

vati strujni udar, požar i/ili dovesti do teških

ozljeda.

Sačuvajte sve sigurnosne napomene i upute

za ubuduće.

Pojam „električni alat“ koji se koristi u sigurnosnim

napomenama odnosi se na električni alat s mrež-

nim napajanjem (s mrežnim kabelom) i na električni

alat s pogonom na baterije (bez mrežnog kabela).

1. Sigurnost radnog mjesta

a) Vaše radno mjesto držite čistim i dobro osvi-

jetljenim. Nered i neosvijetljeno radno područje

mogu uzrokovati nezgode.

b) Električni alat ne koristite u eksplozivnom

okruženju u kojem se nalaze zapaljive tekući-

ne, plinovi ili prašina. Električni uređaji stvaraju

iskre koje mogu zapaliti prašinu ili pare.

c) Djecu i druge osobe držite podalje tijekom ko-

rištenja električnog alata. U slučaju odvlačenja

pažnje možete izgubiti kontrolu nad uređajem.

2. Električna sigurnost

a) Utikač električnog alata mora pristajati u

utičnicu. Utikač se ni na koji način ne smije

mijenjati.

Ne koristite adapterske utikače zajedno s

uzemljenim električnim alatom. Neizmijenjeni

utikači i odgovarajuće utičnice umanjuju rizik od

strujnog udara.

b) Izbjegavajte tjelesni kontakt s uzemljenim

površinama kao što su cijevi, sustavi grijanja,

štednjaci ili hladnjaci. Rizik od strujnog udara

veći je kada je Vaše tijelo uzemljeno.

14

PSFS 250 A1

HR

c) Električni alat zaštitite od kiše i vlage. Prodi-

ranje vode u električni uređaj povećava rizik od

strujnog udara.

d) Ne koristite kabel za druge namjene, primje-

rice za nošenje uređaja, vješanje uređaja ili

izvlačenje utikača iz utičnice. Kabel uređaja

držite podalje od izvora topline, ulja, oštrih

bridova i pokretnih dijelova uređaja. Oštećeni

ili zapetljani kabeli povećavaju rizik od strujnog

udara.

e) Ako električni alat koristite na otvorenom, ko-

ristite samo produžne kabele koji su odobreni

za uporabu na otvorenom. Uporaba takve

vrste produžnog kabela prikladnog za uporabu

na otvorenom umanjuje rizik od strujnog udara.

f) Ako nije moguće izbjeći uporabu električnog

alata u vlažnom okruženju, koristite ﬁdo

sklopku. Korištenje ﬁdo sklopke smanjuje rizik

od strujnog udara.

3. Sigurnost osoba

a) Uvijek budite pažljivi i pazite na ono što radite,

i električnim alatom rukujte razumno. Elek-

trični alat ne koristite ako ste umorni ili pod

utjecajem droga, alkohola ili lijekova. Samo

jedan trenutak nepažnje za vrijeme uporabe

električnog alata može dovesti do ozbiljnih

ozljeda.

b) Nosite osobnu zaštitnu opremu i uvijek nosite

zaštitne naočale. Nošenje osobne zaštitne

opreme kao što je maska protiv prašine, nošenje

sigurnosnih cipela s potplatima koji ne klize,

zaštitnih rukavica, zaštitne kacige ili zaštite za

sluh – ovisno o vrsti i namjeni električnog alata

– umanjuje rizik od ozljeda.

c) Izbjegavajte nehotično uključivanje uređaja.

Uvjerite se da je električni alat isključen prije

nego ga priključite na napajanje i/ili bateriju,

uhvatite ili nosite. Ako prilikom nošenja uređaja

prst držite na prekidaču UKLJ/ISKLJ ili uključeni

uređaj uključite u struju, može doći doći do

nezgode.

d) Alat za podešavanje ili ključeve za matice

uklonite prije uključivanja električnog alata.

Alat ili ključ koji se nalazi u rotirajućem dijelu

uređaja mogu dovesti do ozljeda.

e) Izbjegavajte neprirodan položaj tijela. Pobri-

nite se da čvrsto stojite i održavajte ravnotežu

u svakom trenutku. Na taj ćete način moći bolje

kontrolirati električni alat u neočekivanim situaci-

jama.

f) Nosite prikladnu odjeću. Ne nosite široku

odjeću ili nakit. Kosu, odjeću i rukavice držite

podalje od pokretnih dijelova. Pokretni dijelovi

mogu zahvatiti ležernu, široku odjeću, nakit ili

kosu.

g) Ako je moguće montirati usisivač i sustav za

prihvat piljevine, uvjerite se da su priključeni

i da se ispravno koriste. Uporaba usisivača

može smanjiti ugroženost prašinom.

4. Korištenje i rukovanje električnim

alatom

a) Ne preopterećujte uređaj. Koristite električni

alat prikladan za vrstu posla koji obavljate.

Prikladnim električnim alatom moći ćete bolje

i sigurnije raditi u navedenom području.

b) Ne koristite električne alate s oštećenim preki-

dačima. Električni alat koji ne možete uključiti

i isključiti opasan je i treba ga popraviti.

c) Izvucite utikač iz utičnice i/ili odstranite bateriju

prije nego što započnete podešavati uređaj,

mijenjati pribor ili odložite uređaj. Ova mjera

predostrožnosti onemogućuje nehotično uključi-

vanje uređaja.

d) Električni alat koji se ne koristi čuvajte izvan

dohvata djece. Osobama koje nisu upoznate

s načinom rada uređaja ili nisu pročitale upute

nemojte dozvoliti da koriste uređaj. Električni

alat je opasan ako njime rukuju osobe bez

iskustva.

e) Pažljivo održavajte električni alat. Provjerite

funkcioniraju li svi pokretni dijelovi uređaja

besprijekorno i da možda nisu zaglavljeni,

provjerite da dijelovi uređaja eventualno

nisu odlomljeni ili da dijelovi nisu do te mjere

oštećeni, da ometaju rad električnog alata.

Prije uporabe uređaja oštećene dijelove dajte

popraviti. Uzrok brojnih nezgoda su loše odr-

žavani električni alati.

15

PSFS 250 A1

HR

f) Sav alat za rezanje održavajte oštrim i čistim.

Pažljivo održavani alat za rezanje s oštrim oštri-

cama rjeđe se zaglavljuje i lakše se navodi.

g) Električni alat, pribor i drugi alat koristite pre-

ma odgovarajućim uputama. Pritom u obzir

uvijek uzmite i uvjete rada, kao i vrstu posla

koji treba obaviti. Uporaba električnog alata u

druge svrhe osim ovdje opisanih može uzroko-

vati opasne situacije.

5. Servis

a) Popravak električnog alata prepustite isključivo

kvaliﬁciranim stručnjacima, i koristite samo

originalne rezervne dijelove. Na taj način

osiguravate trajnu sigurnost električnog alata.

b) Kada dođe do oštećenja mrežnog priključnog

voda uređaja, ovaj vod mora biti zamijenjen

posebnim vodom za napajanje, koji možete

nabaviti kod proizvođača ili u servisu za kupce.

Dodatne sigurnosne napomene za

brusilice i polirke

■ OTROVNE PRAŠINE! Obrađivanje štetnih/

otrovnih prašina predstavlja ugrožavanje zdrav-

lja osobe koja rukuje uređajem i osoba koje se

nalaze u blizini.

■ Izbjegavajte brušenje boja sa sadržajem olova

ili drugih materijala štetnih po zdravlje.

■ Ne smije se obrađivati materijal koji sadrži

azbest. Azbest se smatra kancerogenim.

Nosite zaštitne naočale i masku za zaštitu

od prašine!

Dodatne sigurnosne napomene za

površinske glodalice

■ Alat držite za izolirane ručke jer glodalica

može zahvatiti vlastiti kabel. Kontakt s vodom

pod naponom može pod napon dovesti i metal-

ne dijelove uređaja te uzrokovati strujni udar.

■ Koristite samo glodala ispravnog promjera

osovine, prikladna za broj okretaja električnog

alata.

■ Izradak pričvrstite i osiguraje na stabilnoj

podlozi pomoću stega ili na drugi način. Ako

izradak pridržavate samo rukom ili naslanjate

na tijelo, izradak ostaje nestabilan, što može

dovesti do gubitka kontrole.

Originalni pribor / dodatni uređaji

■ Koristite samo pribor i dodatne uređaje nave-

dene u uputama za uporabu, odnosno čiji su

nastavci kompatibilni s uređajem.

Rukovanje

Uređaj nikada ne koristite za druge namjene, i uvijek

samo sa originalnim dijelovima/originalnom opre-

mom. Uporaba drugog alata i dijelova od onih

navedenih i preporučenih u uputama za rukovanje

može dovesti do opasnosti od ozljeda. Koristite

samo potpuno odmotane i neoštećene produžne

kabele kapaciteta najmanje 5 A.

UPOZORENJE!

► Ovaj alat ne koristite za izradu ureza oko

instalacija ili otvora s električnim kabelima

pod naponima ili u zidovima, iza kojih mogu

biti položeni strujni kabeli. Nastavak može

provesti struju kroz alat, što je povezano s

opasnošću od strujnog udara za korisnika.

– Isključite automatske osigurače ili izvadite

klasične osigurače kako biste isključili

napon dotičnog strujnog kruga.

UPOZORENJE!

► Alat uvijek držite za plastično kućište i prilikom

rada s alatom uvijek nosite zaštitne naočale.

16

PSFS 250 A1

HR

Uključivanje/isključivanje

Uključivanje:

♦ Pritisnite prekidač UKLJ/ISKLJ

.

Isključivanje:

♦ Pustite prekidač UKLJ/ISKLJ

.

Podešavanje broja okretaja

♦ Okrećite okretni regulator udesno kako biste

povećali broj okretaja.

♦ Okrećite okretni regulator

ulijevo kako biste

smanjili broj okretaja.

Zamjena alata

NAPOMENA

► Koristite samo pribor za kombiniranu glodalicu

s promjerom osovine od Ø 4,8 mm.

♦ Tipku za blokadu osovine

držite pritisnutom.

♦ Otpustite steznu maticu

pomoću vilastog

ključ okretanjem u smjeru suprotnom od

smjera kazaljke na satu.

♦ Zamjenite alat.

♦ Blokirajte blokadu osovine i steznu maticu

čvrsto stezgnite pomoću ključa .

Nastavci:

Isporučeni nastavci pokrivaju sljedeća područja

primjene:

Višenamjensko glodalo (HSS)

:

Prikladnost: Drvo, iverica, plastika, aluminij i

željezni lim

Glodalo za utore (HSS)

:

Prikladnost: Drvo, iverica, plastika

Brusne trake

:

Prikladnost: Brušenje drveta

NAPOMENA

► Za rezanje zidnih pločica i/ili obradu limo-

va/lakih metala, molimo koristite odgovaraju-

ći pribor iz specijalističkih trgovina.

Montiranje brusnih traka

♦ Gurnite brusnu traku odozgo na klin za zate-

zanje brusne trake

. Zategnite vijak na klinu

za zatezanje brusne trake kako biste ﬁksirali

brusnu traku .

♦ Montirajte brusne trake

kao što je opisano

u poglavlju „Zamjena alata“.

Podešavanje radne dubine

♦ Otpustite leptirastu maticu .

♦ Gurnite osnovnu ploču

na željenu dubinu

(za potpuno prorezivanje otprilike 3,2 mm više

od debljine materijala). Najveća preporučena

dubina reza za drva je 13mm *(odnosi se

samo na višenamjensko glodalo (HSS) ).

♦ Ponovo zategnite leptirastu maticu

.

Smjer glodanja na rubovima

Izvođenje ubodnog reza

♦ Uvedite nastavak u izradak pod kutom od 45°.

♦ Nastavak polako uspravite pod kutom od 90°

kako biste započeli rez.

NAPOMENA

► Osnovna ploča

mora skroz nalijegati na

površinu materijala.

17

PSFS 250 A1

HR

Zakretanje ručke

NAPOMENA

► Nije dopušteno zakretati ručku prilikom pušta-

nja u pogon. Izvucite utikač iz utičnice i pobri-

nite se da je blokada nagiba

zaglavljena.

Zakretanje u vodoravan položaj:

♦ Pritisnite blokadu nagiba

i držite je pritisnutu.

♦ Zakrenite ručku u smjeru suprotnom od smjera

kazaljke na satu

iz vertikalnog u horizontal-

ni položaj, sve dok blokada nagiba ne ulegne.

Zakretanje u okomiti položaj:

♦ Pritisnite blokadu nagiba

i držite je pritisnutu.

♦ Zakrenite ručku u smjeru kazaljke na satu

iz horizontalnog u vertikalni položaj, sve dok

blokada nagiba ne ulegne.

Uporaba paralelne vodilice

♦ Otpustite leptiraste vijke osnovne ploče i

gurnite vodilicu nastavka za kružno/paralelno

rezanje kroz dva otvora na donjoj strani

osnovne ploče tako da paralelna vodilica

pokazuje prema dolje.

♦ Poravnajte alat na željenoj udaljenosti od ruba

izratka. Zategnite leptiraste vijke

kako biste

nastavak za kružno/paralelno rezanje

pričvrstili na osnovnu ploču .

Piljenje krugova

NAPOMENA

► Osnovnu rupu ovisno o željenom rezultatu

postavite iznutra ili izvana: Iznutra za rupu –

izvana za ploču. Radijus se može ﬁksirati

od 5 do 16 cm.

♦ Iscrtajte krug na izratku.

♦ Označite središte kruga i izbušite rupu u središtu

(ubodni rez).

♦ Izbušite vodeću rupu na rubu kruga (ubodni

rez) (promjer rupe 3 mm).

♦ Otpustite leptiraste vijke

osnovne ploče i

gurnite vodilicu nastavka za kružno/paralelno

rezanje

kroz dva otvora na donjoj strani

osnovne ploče tako da vrh za centriranje

pokazuje prema dolje.

♦ Utaknite vrh za centriranje u središte kruga.

♦ Poravnajte razmak nastavka na kružno/paralel-

no rezanje

tako da nastavak uliježe u vodeću

rupu na rubu kruga.

♦ Zaključajte osnovnu ploču

pritezanjem

leptirastih vijaka .

♦ Uređaj uključite pritiskanjem i držanjem prekidača

UKLJ/ISKLJ

.

♦ Uređaj polako gurajte prema naprijed.

Usisavanje prašine

■ Alat je opremljen nastavkom za usisavanje

za priključak usisivača za prašinu.

♦ Umetnite adapter u nastavka za usisavanje .

♦ Na adapter

priključite usisivač.

Uporaba alata u trajnom pogonu

Blokada prekidača UKLJ/ISKLJ :

♦ Pritisnite prekidač UKLJ/ISKLJ

.

♦ Sada pritisnite prekidač za blokadu

i pustite

prekidač UKLJ/ISKLJ .

Otključavanje prekidača UKLJ/ISKLJ

:

♦ Pritisnite prekidač UKLJ/ISKLJ

i ponovno ga

pustite.

Pagina se încarcă ...

Parkside PSFS 250 A1 Original Instructions Manual

Parkside PSFS 250 A1 Original Instructions Manual

Lucrări conexe

Alte documente