Parkside PFBS 160 A1 Operation and Safety Notes

PRECISION MULTI-GRINDER PFBS 160 A1

MAŞINĂ DE GĂURIT ŞI ŞLEFUIT FIN

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

АКУМУЛАТОРЕН МУЛТИШЛАЙФ

Инструкции за обслужване и безопасност

Превод на оригиналното ръководство за експлоатация

FEINBOHRSCHLEIFER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

ΣΥΣΚΕΥΗ ΛΕΙΑΝΣΗΣ & ΔΙΑΤΡΗΣΗΣ

Υποδείξεις χειρισμού και ασφαλείας

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

PRECIZNA BUŠILICA-BRUSILICA

Upute za posluživanje i za Vašu sigurnost

Prijevod originalnih uputa za uporabu

PRECISION MULTI-GRINDER

Operation and Safety Notes

Translation of the original instructions

IAN 273280

GB Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 19

RO Instrucţiuni de utilizare şi de siguranţă Pagina 33

BG Инструкции за обслужване и безопасност Страница 47

GR Υποδείξεις χειρισμού και ασφαλείας Σελίδα 63

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 79

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Rasklopite prije čitanja obije stranice sa slikama i nakon toga se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi ambele pagini cu imagini şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете двете страници с фигурите и след това се запознайте с всички

функции на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

2

9

4 3

10 11

B

1

7

6 5

A

18 1312

14 b

14

15

16

17

23

2120

22

242526

7

2729 283031

32

33

34

ON

OFF

C

36

1935

8

7

D

F G

H

E

I

J

16

17

3

14 b

14

18

5 GB

Table of contents

Introduction

Intended use ........................................................................................................................................ Page 6

Features ...............................................................................................................................................Page 6

Scope of delivery ................................................................................................................................Page 6

Technical Data ....................................................................................................................................Page 6

General power tool safety warnings

1. Work area safety............................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 8

4. Power tool use and care ................................................................................................................Page 8

5. Service .............................................................................................................................................Page 8

Safety instructions for all operations .................................................................................................. Page 9

Further safety instructions for all operations ......................................................................................Page 10

Additional safety instructions for grinding and cutting-off operations .............................................Page 11

Additional safety instructions for wire brushing operations ..............................................................Page 11

Safety notices specific to rotary tools ................................................................................................Page 11

Safety instructions for LED lights ......................................................................................................... Page 12

Safety Instructions for batteries ..........................................................................................................Page 12

Original accessories / tools ................................................................................................................Page 12

Start-up

Attaching / changing the tool / collet ................................................................................................. Page 12

Brick .....................................................................................................................................................Page 13

Installing sanding belts .......................................................................................................................Page 13

Attaching polishing tools ....................................................................................................................Page 13

Switching on and off / Adjusting the speed .......................................................................................Page 13

Using the grip collar with LED light ....................................................................................................Page 13

Information about processing materials / tool / speed range ..........................................................Page 13

Tips and tricks ...................................................................................................................................... Page 15

Flexible shaft ........................................................................................................................................Page 15

Stretch stand for the multi-function tool ..............................................................................................Page 15

Base assembly .....................................................................................................................................Page 15

Changing the battery .......................................................................................................................... Page 16

Cleaning, care and storage .............................................................................................Page 16

Warranty .........................................................................................................................................Page 16

Disposal ............................................................................................................................................Page 17

Translation of the original declaration of conformity /

Manufacturer ............................................................................................................................... Page 17

6 GB

Introduction / General power tool safety warnings

Introduction

Precision Multi-Grinder PFBS 160 A1

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Intended use

The precision multi-grinder, hereafter also referred

to as tool, is intended for drilling, milling, engraving,

polishing, cleaning, sanding, and cutting wood,

metal, plastic, ceramics or masonry in dry areas.

Any other uses, and / or modiﬁcations to the tool

are considered improper use and may result in seri-

ous hazards. Not for commercial applications.

Features

Precision Multi-Grinder:

1

ON / OFF switch

2

Mains lead

3

Metal bracket

4

Louvres

5

Union nut

6

Clamping nut

7

Collet 3.2 mm (pre-assembled)

8

Grip collar with LED light

9

Spindle lock button

10

Carbon brushes cover

11

Variable speed control

Accessories (see Fig. A):

12

Locking screw

13

Base assembly

14

Flexible shaft

14 b

Union nut (Flexible shaft)

15

Collet chuck

16

Stand support

17

Stretch stand

18

Clamp

Accessory kit (42 pieces) (see Fig. B):

19

6 Cutting discs

20

2 Grinding discs, abrasive

21

1 Brick

22

3 Polishing attachments

23

5 Sanding belts

24

1 Sanding belt clamping mandrel

25

1 Combination wrench

26

1 Collet 2.4 mm

27

1 Metal brush

28

2 Plastic brushes

29

1 Clamping mandrel for cut-oﬀ / grinding discs

30

1 Drill bit

31

1 Milling bit

32

1 Clamping mandrel for polishing attachments

33

2 Engraving bits

34

5 Grinding bits, abrasive

35

8 Cutting discs

36

LED light ON / OFF switch

Scope of delivery

1 Precision Multi-Grinder PFBS 160 A1

1 Plastic case

1 Flexible shaft

1 Stretch stand

1 Clamp

1 Base assembly

1 Grip collar with LED light

1 Accessory kit (42 pieces)

1 Set of operating instructions

Technical Data

Rated power input: 160 W

Voltage: 230–240 V∼, 50 Hz

Idle speed: n 10,000–40,000 min

-1

Drill bit

diameter

: max. ø 3.2 mm

Disc: max. ø 25 mm

Protection class: II /

7 GB

Introduction / General power tool safety warnings

Noise emission value:

Measured values for noise are determined in accord-

ance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: L

= 80 dB(A)

Uncertainty K

: 3 dB(A)

Sound power level: L

= 91 dB(A)

Uncertainty K

: 3 dB(A)

Wear ear protection!

Vibration values (vector sum in three

directions) determined according to

EN 60745:

Vibration emission value a

h

= 2.3 m / s

2

Uncertainty K = 1.5 m / s

2

Note: The vibration level speciﬁed in these instruc-

tions was measured in accordance with an EN 60745

standardised measurement process and can be used

to compare equipment. The vibration emission value

speciﬁed can also serve as a preliminary assessment

of the exposure.

The vibration level will change according to the

application of the electrical tool and in some cases

may exceed the value speciﬁed in these instructions.

Regularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Try to keep the vibration loads

as low as possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the work-

ing time. Wherein all states of operation must be in-

cluded (e.g. times when the power tool is switched

oﬀ and times where the power tool is switched on but

running without load).

General power tool

safety warnings

Read all safety

warnings and all instructions.

Failure to follow the warnings and in-

structions may result in electric shock, ﬁre and / or

serious injury.

Save all warnings and instructions for

future reference!

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-op-

erated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) D

o not operate power tools in explosive

atmospheres, such as in the presence

of flammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distractio

ns

can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plug

s

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e)

When operating a power tool outdo

ors,

use an extension cord suitable for out-

door use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

Introduction

8 GB

General power tool safety warnings

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing

and use common sense when operat-

ing a power tool. Do not use a power

tool while you are tired or under the

influence of drugs, alcohol or medica-

tion. A moment of inattention while operating

power tools may result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal in-

juries.

c) Avoid accidental starting. Verify the po-

wer tool is switched oﬀ before connec-

ting it to the mains and / or connecting

the battery, picking it up, or carrying it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper foot-

ing and balance at all times. This enables

better control of the power tool in unexpected

situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from mov-

ing parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collection

can reduce dust-related hazards.

4. Power tool use and care

a) Do not force the power tool. Use the

correct power tool for your applica

tion.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch is

dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of un-

trained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other con-

dition that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations diﬀerent from those intended could

result in a hazardous situation.

5. Service

a) Have your power tool serviced by a

qualified repair person using only

iden-

9 GB

General power tool safety warnings

tical replacement parts. This will ensure

that the safety of the power tool is maintained.

Safety instructions for all

operations

Safety warnings common for grinding,

sanding, wire brushing, polishing, carving

or abrasive cutting-off operations:

a) This power tool is intended to function

as a grinder, sander, wire brush, pol-

isher, carving or cut-off tool. Read all

safety warnings, instructions, illustra-

tions and specifications provided with

this power tool. Failure to follow all instruc-

tions listed below may result in electric shock,

ﬁre and / or serious injury.

b) Do not use accessories which are not

specifically designed and recommend-

ed by the tool manufacturer. Just because

the accessory can be attached to your power

tool, it does not assure safe operation.

c) The rated speed of the grinding acces-

sories must be at least equal to the

max-

imum speed marked on the power

tool.

Grinding accessories running faster than their

rated speed can break and ﬂy apart.

d) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool. In-

correctly sized accessories cannot be ade

quately

controlled.

e) The arbour size of wheels, sanding

drums or any other accessory must

properly fit the spindle or collet of the

power tool. Accessories that do not match

the mounting hardware of the power tool will

run out of balance, vibrate excessively and may

cause loss of control.

f) Mandrel mounted wheels, sanding

drums, cutters or other accessories

must be fully inserted into the collet

or chuck. If the mandrel is insuﬃciently held

and / or the overhang of the wheel is too long,

the mounted wheel may become loose and be

ejected at high velocity.

g) Do not use a damaged accessory. Be-

fore each use inspect the accessory

such

as abrasive wheels for chips and cra

cks,

sanding drum for cracks, tear or excess

wear, wire brush for loose or cracked

wires. If power tool or accessory is

dropped, inspect for damage or install

an undamaged accessory. After in

spect-

ing and installing an accessory, position

yourself and bystanders away from

the plane of the rotating accessory

and

run the power tool at maximum no-

load

speed for one minute. Damaged accesso-

ries will normally break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glass-

es. As appropriate, wear dust mask,

hearing protectors, gloves and work-

shop apron capable of stopping small

abrasive or workpiece fragments. The

eye protection must be capable of stopping

ﬂying debris generated by various operations.

The dust mask or respirator must be capable of

ﬁltrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protec-

tive equipment. Fragments of workpiece or

of a broken accessory may ﬂy away and cause

injury beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an

op-

eration where the cutting accessory may

contact hidden wiring or its own cord.

Cutting accessory contacting a «live» wire may

make exposed metal parts of the power tool

«live» and could give the operator an electric shock.

k) Always hold the tool firmly in your

hand(s) during the start-up. The reaction

torque of the motor, as it accelerates to full

speed,

can cause the tool to twist.

l) U

se clamps to support workpiece wh

en-

ever practical. Never hold a small

work-

piece in one hand and the tool in the

other hand while in use. Clamping a small

General power tool safety warnings

10 GB

General power tool safety warnings

workpiece allows you to use your hand(s) to

control the tool. Round material such as dowel

rods, pipes or tubing have a tendency to roll

while being cut, and may cause the bit to bind

or jump toward you.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

n) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

o) After changing the bits or making any

adjustments, make sure the collet nut,

chuck or any other adjustment devices

are securely tightened. Loose adjustment

devices can unexpectedly shift, causing loss of

control, loose rotating components will be vio-

lently thrown.

p) Do not run the power tool while car-

rying it at your side. Accidental contact

with the spinning accessory could snag your

clothing, pulling the accessory into your body.

q) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust inside

the housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

r) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

s) Do not use accessories that require

liquid coolants. Using water or other liquid

coolants may result in electrocution or shock.

Further safety instructions

for all operations

Kickback and related warnings

Kickback is a sudden reaction to a pinched or sn

agged

rotating wheel, sanding band, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these con-

ditions.

Kickback is the result of power tool misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool

and position your body and arm to al-

low you to resist kickback forces. The

operator can control kickback forces, if proper

precautions are taken.

b) U

se special care when working corne

rs,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

c)

Do not attach a toothed saw blade. S

uch

blades create frequent kickback and loss of

control.

d) Always feed the bit into the material

in the same direction as the cutting

edge is exiting from the material

(which

is the same direction as the chips are

thrown). Feeding the tool in the wrong direc-

tion causes the cutting edge of the bit to climb

out of the work and pull the tool in the direction

of this feed.

e) When using rotary files, cut-off wheels,

high-speed cutters or tungsten carbide

cutters, always have the work securely

clamped. These wheels will grab if they be-

come slightly canted in the groove, and can

kickback. When a cut-oﬀ wheel grabs, the

wheel itself usually breaks. When a rotary ﬁle,

high-speed cutter or tungsten carbide cutter

grabs, it may jump from the groove and you

could lose control of the tool.

11 GB

General power tool safety warnings

Additional safety instructions

for grinding and cutting-oﬀ

operations

Safety warnings specific for grinding and

abrasive cutting-off operations:

a) Use only wheel types that are recom-

mended for your power tool and only

for recommended applications.

For example: do not grind with the

side of a cut-off wheel. Abrasive cut-oﬀ

wheels are intended for peripheral grinding,

side forces applied to these wheels may cause

them to shatter.

b) For threaded abrasive cones and plugs

use only undamaged wheel mandrels

with an unrelieved shoulder flange that

are of correct size and length. Proper

man-

drels will reduce the possibility of breakage.

c) Do not “jam” a cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut. Over-

stressing the wheel increases the loading and

susceptibility to twisting or snagging of the wheel

in the cut and the possibility of kickback or w

heel

breakage.

d) Do not position your hand in line with

and behind the rotating wheel. When

the wheel, at the point of operation, is moving

away from your hand, the possible kickback m

ay

propel the spinning wheel and the power tool

directly at you.

e) When wheel is pinched, snagged or

when interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

comes to a complete stop. Never att

empt

to remove the cut-off wheel from the

cut while the wheel is in motion other-

wise kickback may occur. Investigate and

take corrective action to eliminate the cause of

wheel pinching or snagging.

f) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if

the power tool is restarted in the workpiece.

g) Support panels or any oversized work-

piece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight. Supports

must be placed under the workpiece near the

line of cut and near the edge of the workpiece

on both sides of the wheel.

h) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Additional safety instructions

for wire brushing operations

Safety warnings specific for wire brushing

operations:

a) Be aware that wire bristles are thrown

by the brush even during ordinary op-

eration. Do not overstress the wires

by applying excessive load to the

brush.

The wire bristles can easily penetrate light cloth-

ing and / or skin.

b)

Allow brushes to run at operating spe

ed

for at least one minute before using

them. During this time no one is to

stand

in front or in line with the brush. Loose

bristles or wires will be discharged during the

run-in time.

c) D

irect the discharge of the spinning wir

e

brush away from you. Small particles and

tiny wire fragments may be discharged at high

velocity during the use of these brushes and

may become imbedded in your skin.

Safety notices speciﬁc to

rotary tools

When you use the drill / grinder wear the fol-

lowing protective equipment: safety glasses and

protective gloves.

CAUTION! RISK OF INJURY! The tool

continues to rotate after it has been switched

oﬀ! Avoid contact with rapidly rotating drill /

grinder components.

General power tool safety warnings

12 GB

Start-up

General power tool safety warnings / Start-up

Securely support the work-

piece. Use clamps or a vice to grip the workpiece

ﬁrmly. This is much safer than holding it in your

hand.

RISK OF INJURY! Never

support yourself by placing your hands near or

in front of the device or the workpiece surface.

A slip can result in injury.

DANGER OF FIRE FROM FLYING

SPARKS!

Abrading metal creates ﬂying sparks. For this

reason, always make sure that nobody is placed

in any danger and that there are no inﬂamma

ble

materials near the working area.

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person

operating the device and to anyone near the

work area.

Wear a dust mask!

TOXIC DUST! Ensure that

there is adequate ventilation when machining

surfaces containing plastic or covered with

paint, varnish etc.

Its use as a saw or the use of saw blades with

this device is prohibited.

Do not soak the materials or the surface you are

about to work on with liquids containing solvents.

Avoid abrading paints containing lead or other

substances hazardous to health.

Do not machine materials containing asbestos.

Asbestos is a known carcinogen.

Avoid contact with moving sanding or grinding tools.

Do not machine moist materials or damp surface

s.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

RISK OF INJURY!

Switch the device oﬀ and allow it to come to a

standstill before you put it down.

Always keep the device

clean, dry and free of oil or grease.

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited must

never be allowed to use the device without super-

vision or instruction by a person responsible for

their safety. Children must never be allowed to

play with the device.

Safety instructions for LED lights

ATTENTION! RISK OF EYE INJURY! Never

aim the light beam directly at people or animals,

and never look directly into the light beam of

LED lights.

Safety Instructions for batteries

ATTENTION!

Do not leave drained battery in the device, as

even leak-proof batteries can corrode, releasing

chemicals which could be harmful to your health

or ruin the device.

Do not leave batteries lying about carelessly.

Children or pets could swallow them. If acciden-

tally swallowed seek immediate medical attention

.

Remove the batteries from the device when it

will not be used for extended periods to prevent

leaks.

Touching leaked or damaged batteries may

cause chemical burns. Therefore wear suitable

protective gloves in this event.

Ensure batteries are not short-circuited. Never

throw batteries into ﬁre.

Do not recharge batteries. Explosion hazard!

Original accessories / tools

Use only the accessories and attachments de-

t

ailed in the operating instructions, or those w

hich

are compatible with the tool.

Start-up

Attaching / changing the

tool / collet

Press and hold the spindle lock

9

.

Turn the clamping nut

6

until the lock catches.

Loosen the clamping nut

6

using the combi-

nation wrench

25

for the thread.

If applicable, remove the attached tool.

13 GB

Start-up

First slide the tool you wish to use through the

clamping nut

6

before inserting it into the

collet

7

,

26

ﬁtting the tool shaft.

Press and hold the spindle lock

9

.

Insert the collet

7

,

26

into the threaded insert,

then tighten the clamping nut

6

using the

combination wrench

25

on the thread.

Using a tool with clamping mandrel:

Use the screwdriver end of the combination

wrench

25

to loosen and tighten the screw on

the clamping mandrels.

Insert the clamping mandrel in the tool as de-

scribed.

Using the combination wrench

25

, loosen the

screw on the clamping mandrel.

Insert the attachment you wish to use onto the

screw between two washers.

Use the combination wrench

25

to tighten the

screw on the clamping mandrel.

Brick

Do not resharpen any edges by hand with

the brick

21

.

Installing sanding belts

Slide the grinding belt

23

onto the grinding man-

drel

24

from the top. Tighten the screw on the grind-

ing mandrel

24

to secure the grinding belt

23

.

Attaching polishing tools

Turn the polishing attachment

22

on the point

of the mandrel for polishing attachments

32

.

Switching on and oﬀ /

Adjusting the speed

Switching on / adjusting the speed:

Set the ON / OFF switch

1

to position „I“ by

pressing down and sliding it forward.

Set the variable speed control

11

to a position

between „1“ and „MAX“.

Switching off:

Set the ON / OFF switch

1

to position „0“.

Using the grip collar with LED light

Hold the spindle lock

9

and unscrew the

clamping nut

6

from the thread, turning coun-

ter-clockwise.

Release the spindle lock

9

.

Then screw the union nut

5

anti-clockwise from

the thread.

Screw the grip collar with LED light

8

onto the

thread, turning clockwise.

Hold the spindle lock

9

and screw the clamp-

ing nut

6

onto the thread, turning clockwise.

Release the spindle lock

9

.

Set the ON / OFF switch of the LED light

36

to

position “I“ to switch it on (see Fig. C).

Set the ON / OFF switch of the LED light

36

to

position “0“ to switch it oﬀ again.

Repeat the steps in reverse order to reattach the

union nut

5

.

Information about processing

materials / tool / speed range

Use the router bits to process wood, plastic and

sheetrock at maximum speed.

Determine the speed range for processing zinc,

zinc alloys, aluminium, copper and lead by

testing scrap pieces.

Process plastics and materials with a low melt-

ing point at a low speed.

Process wood at high speeds.

Clean, polish and buﬀ at a medium speed.

Note: The milling bit

31

is not intended for use on

steel or iron. Suitable milling bits are available.

The following information are non-binding recom-

mendations. When performing the actual work also

test yourself, which tools and settings are ideal for

the material you are working on.

General power tool safety warnings / Start-up

14 GB

Start-up

Setting the appropriate speed:

Numeral on the

rotational speed

control

11

Material to be

worked on

1

Plastics and low melting

point materials

2–3

Stone, Ceramics

4

Softwood, metal

5

Hardwood

Max.

Steel

Examples of appropriate tool selection Function:

Function Accessory Application Projection

(min–max) mm

Drilling

Drill

30

Drilling wood 18–25 when us-

ing the smallest

drill the projection

is 10 mm

Milling

Milling bit

31

Various tasks, e.g. hollowing out, gouging,

shaping, grooving or slotting

18–25

Engraving Engraving

bits

33

Making marks, craft projects

(see Fig. D)

18–25

Polishing, derusting

CAUTION!

Use only the lightest

contact pressure of

the tool on the

workpiece.

Metal brush

27

Derusting

9–15

Polishing attach-

ments

22

Working on various metals and plastics,

in particular noble metals like gold or

silver (see Fig. F)

12–18

Cleaning

Plastic brush

28

E.g. cleaning complex plastic housings

or the area around a door lock

9–15

Grinding Grinding

wheels

20

Grinding work on stone, wood; ﬁne

work on hard materials such as ceramic

or alloyed steel (see Fig. G)

12–18

10

Grinding bits

34

Sanding belts

23

10

Cutting and sawing

Cutting discs

35

,

19

Cutting metal,

plastic or wood

12–18

Be sure not to exceed the maximum diameter of

composite abrasive wheels and grinding cones

and cylinders with 55 mm thread insert, and

the 80 mm maximum diameter of sandpaper

grinding accessories.

Note: The max. permissible mandrel length is

33 mm.

15 GB

Start-up

Store accessories inside the original box or oth-

erwise protect the accessories from damage.

Store accessories dry and away from aggres-

sive media.

Tips and tricks

Applying excessive pressure can cause the in-

stalled tool to break and / or damage the work

piece. Optimal results can be achieved by ap-

plying the tool to the work piece at a steady

speed range and little pressure.

Hold the device with both hands whilst cutting.

Please note the data and information in the

chart to prevent the spindle end touching the

perforated plate of the grinding tool.

Flexible shaft

Never use the spindle lock with the motor on.

The tool or the ﬂexible shaft could otherwise

be damaged.

Unscrew the union nut

5

from the tool, turning

counter-clockwise, and put aside.

Press and hold the spindle lock

9

.

Unscrew the clamping nut

6

from the tool,

turning counter-clockwise.

Attach the ﬂexible shaft

14

to the tool, inserting

the inner axle on the ﬂexible shaft along with

the clamping nut

6

into the collet

7

,

26

.

Use the combination wrench

25

to ﬁrst tighten t

he

clamping nut

6

, then the union nut

14 b

of the

ﬂexible shaft

14

to the tool, turning clockwise.

Now insert the accessory you wish to use into

the collet

7

,

26

of the ﬂexible shaft.

To lock the spindle, slide back the black sleeve

on the ﬂexible shaft.

Using the combination wrench

25

, open the

collet holder

15

on the ﬂexible shaft, insert the

accessory and tighten the collet holder

15

.

Stretch stand for the

multi-function tool (Fig. J)

Screw the stretch stand

17

into the clamp

18

.

Note: The stretch stand

17

can be screwed

into the clamp in two diﬀerent positions, de-

pending on the whether you‘re attaching to a

horizontal or vertical surface.

Secure the clamp

18

at the edge of a work-

bench or a work table no thicker than 55 mm.

The stretch stand

17

is height adjustable. Loosen

the upper tube of the stretch stand

17

by turning

to the left (–). Extend the tube to the maximum

height and secure by turning to the right (+).

The holder

16

is also height adjustable, simple

turn the black thread to the left. After adjusting

the holder to the correct height, turn the thread

in the opposite direction to tighten.

Secure the tool to the holder

16

of the stretch

stand

17

with the metal bracket

3

. This hold-

er

16

rotates by 360°.

Base assembly

Using the attachment, the tool is particularly suited

for cutting special shapes (holes for sockets, etc.).

Attach the milling bit

31

as described in chapter

„Attaching / changing the tool / collet“.

Ensure that the bit’s shaft protrudes from collet

by approx. 13 mm.

Unscrew the union nut

5

from the tool, turning

clockwise, and put aside.

Screw the base

13

onto the unit.

To set the correct working depth, loosen the

locking screw

12

and adjust the bottom of the

base assembly to the desired size.

Then tighten the locking screw

12

.

Start-up

16 GB

… / Disposal / Translation of the original declaration of conformity / Manufacturer

Start-up / Cleaning, care and storage / Warranty

1312

31

approx. 13 mm

Changing the battery

Ensure the LED light is switched oﬀ. Remove the

three battery cover screws at the back of the

grip collar with LED

8

.

Remove the drained battery and replace with a

new battery (button cell LR41). Please note the

correct polarity when inserting the batteries.

Close the battery compartment by fastening the

three screws.

Cleaning, care and storage

RISK OF INJURY! Switch the

tool oﬀ and pull the plug out of the mains socket

before carrying out any work on the tool.

Always keep the tool clean, dry and free of oil

or grease.

Use a dry cloth to clean the housing.

If the connection cable needs to

be replaced, this repair must be performed by

the manufacturer or a representative to prevent

safety hazards.

Carefully store the tool and all parts in desig-

nated plastic case to prevent losing any parts.

Note: Spare parts not listed (e.g. carbon brushes,

switches) can be ordered through our call centre.

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tampering

not carried out by our authorized service branch. Your

statutory rights are not restricted in any way by this

warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

17 GB

… / Disposal / Translation of the original declaration of conformity / Manufacturer

GB

Service Great Britain

Tel.: 0871 5000 720

(0.10 GBP / Min.)

e-mail: k[email protected]

IAN 273280

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive

2012 / 19 / EU

about waste electrical and electronic equipment

and its transposition into national legislation, worn

out electric tools must be collected separately and

taken for environmentally compatible recycling.

Please contact your municipal or city council to ask

about how to dispose of old electrical tools.

Batteries may not be disposed

of in household waste!

Every consumer is legally obligated to return batter-

ies to a municipal collection site or a retail store.

This duty is to ensure batteries are disposed of in

an environmentally friendly manner. Only return

drained batteries.

Translation of the original

declaration of conformity /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-2-23:2013

EN 60745-1:2009+A11:2010

EN 55014-1:2006/+A1:2009/+A2:2011

EN 55014-2:1997/+A1:2001/+A2:2008

EN 61000-3-2:2006/+A1:2009/+A2:2009

EN 61000-3-3:2013

Type / Appliance Designation:

Precision Multi-Grinder PFBS 160 A1

Date of manufacture (DOM): 12–2015

Serial number: IAN 273280

Bochum, 31.12.2015

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcat

ions

in the course of further development.

Start-up / Cleaning, care and storage / Warranty

18

Popis sadržaja

19 HR

Popis sadržaja

Uvod

Namjenska uporaba ..................................................................................................................... Stranica 20

Oprema ......................................................................................................................................... Stranica 20

Opseg isporuke ............................................................................................................................. Stranica 20

Tehnički podaci ............................................................................................................................. Stranica 20

Opće sigurnosne upute za električni alat

1. Sigurnost na radnom mjestu .................................................................................................... Stranica 21

2. Električna sigurnost ................................................................................................................... Stranica 21

3. Sigurnost osoba ........................................................................................................................ Stranica 22

4. Pažljivo postupanje s električnim uređajima i njihovo korištenje ........................................... Stranica 22

5. Servis ......................................................................................................................................... Stranica 23

Sigurnosne upute za sve primjene ............................................................................................... Stranica 23

Daljnje sigurnosne upute za sve primjene ................................................................................... Stranica 24

Dodatne sigurnosne upute za brušenje i rezanje ....................................................................... Stranica 25

Dodatne sigurnosne upute za rad sa žičanim četkama ............................................................. Stranica 26

Za dotični uređaj karakteristične sigurnosne upute za preciznu bušilicu-brusilicu .................... Stranica 26

Sigurnosne upute za LED-svjetiljke ............................................................................................... Stranica 27

Sigurnosne upute za baterije ....................................................................................................... Stranica 27

Originalna oprema / dodatni uređaji .......................................................................................... Stranica 27

Stavljanje u pogon

Alat / stezna čahura umetanje / zamjena .................................................................................... Stranica 27

Brusni kamen ................................................................................................................................. Stranica 27

Postavljanje brusnih traka ............................................................................................................. Stranica 27

Montiranje nastavka za poliranje ................................................................................................ Stranica 27

Uključivanje i isključivanje / namještanje raspona broja okretaja ............................................. Stranica 28

Upotreba prstena s drškom s LED-svjetlom .................................................................................. Stranica 28

Upute za obrađivanje materijala / alati / raspon broja okretaja ............................................... Stranica 28

Savjeti i trikovi ............................................................................................................................... Stranica 29

Fleksibilna osovina ........................................................................................................................ Stranica 30

Stalak za višenamjenski alat ........................................................................................................ Stranica 30

Košara za glodanje ...................................................................................................................... Stranica 30

Izvedba zamjene baterija ............................................................................................................ Stranica 31

Čišćenje, njega i pohranjivanje .............................................................................. Stranica 31

Jamstveni list.......................................................................................................................... Stranica 31

Zbrinjavanje ........................................................................................................................... Stranica 32

Prijevod originalnog-EG-objašnjenja sukladnosri / Prozvođač .... Stranica 32

20 HR

Uvod

Precizna bušilica-brusilica

PFBS 160 A1

Uvod

Čestitamo Vam na kupnji novog uređaja. Ovom

kupnjom odlučili ste se za visokokvalitetan proizvod.

Uputa za uporabu je sastavni dio ovog proizvoda.

Ona sadrži važne upute o sigurnosti, uporabi i

uklanjanju otpada. Prije upotrebe proizvoda upoz-

najte se sa svim njegovim uputama za korištenje i

sigurnosnim uputama. Koristite ovaj proizvod u skla-

du s navedenim uputama te u navedene svrhe. Uko-

liko proizvod dajete nekoj drugoj osobi, predajte toj

osobi također i sve upute.

Namjenska uporaba

Precizna bušilica-brusilica, u daljnjem tekstu označuje

se kao uređaj, koristiti se za bušenje, glodanje, rez-

barenje, poliranje, čišćenje, brušenje, rezanje drva,

metala, plastike ili kamena u suhim prostorijama. Sva-

ki drugi oblik upotrebe, kao i svaka promjena stroja

smatra se nenamjenskom i sa sobom nosi znatne opas-

nosti od nezgode. Proizvod se ne smije upotrebljavati

u komercijalne svrhe.

Oprema

Precizna bušilica-brusilica:

1

sklopka za UKLJUČIVANJE / ISKLJUČIVANJE

2

mrežni kabel

3

metalna poluga

4

otvori za prozračivanje

5

nasadna matica

6

zatezna matica

7

stezna čahura 3,2 mm (prethodno montirana)

8

prsten s drškom s LED svjetlom

9

tipka za zapor vretena

10

ugljene četkice

11

kontinuirani regulator broja okretaja

Pribor (vidi sl. A):

12

zaporni vijak

13

košara za glodanje

14

ﬂeksibilna osovina

14 b

nasadna matica (ﬂeksibilna osovina)

15

držač stezne čahure

16

stalak držača

17

stalak

18

naprava za stezanje

Set pribora 42 dijelova (vidi sl. B):

19

6 reznih ploča

20

2 ploče za poliranje, abrasivna

21

1 brusni kamen

22

3 nastavka za poliranje

23

5 brusnih traka

24

1 stezni trn za brusnu traku

25

1 univerzalni ključ

26

1 stezna čahura 2,4 mm

27

1 metalna četka

28

2 plastične četke

29

1 stezni trn za reznu / brusnu ploču

30

1 svrdlo

31

1 bit za glodanje

32

1 stezni trn za nastavke za poliranje

33

2 bita za rezbarenje

34

5 bitova za brušenje, abrazivna

35

8 reznih ploča

36

prekidač za UKLJUČIVANJE / ISKLJUČIVANJE

LED-svjetla

Opseg isporuke

1 precizna bušilica-brusilica PFBS 160 A1

1 plastični kofer

1 ﬂeksibilna osovina

1 stalak

1 sprava za stezanje

1 košara za glodanje

1 prsten s drškom s LED svjetlom

1 set pribora (42 dijelova)

1 upute za korištenje

Tehnički podaci

Nazivni prijem: 160 W

Napon: 230–240 V∼, 50 Hz

Broj okretaja u

praznom hodu: n 10.000–40.000 min

-1

Uvod / Opće sigurnosne upute za električni alat

Pagina se încarcă ...

Parkside PFBS 160 A1 Operation and Safety Notes

Parkside PFBS 160 A1 Operation and Safety Notes

Lucrări conexe

Alte documente