Mellanox Technologies MIS5200Q-4DNC Hardware Installation Manual

www.mellanox.com

216-Port InfiniBand QDR SwitchX®

Switch Platform Hardware Installation Guide

PN:MIS5200Q-4DNC

Rev 1.6

Document Number: 3268

Mellanox Technologies

2

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

3

Table of Contents

List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.1 Installation Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.2 Environmental and Safety Recommendations . . . . . . . . . . . . . . . . . . . . 14

1.3 Chassis Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.4 Leaf Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.5 Management Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.6 Physical Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.6.1 ESD Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.6.2 Installing the Cable Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

1.6.3 Installing the Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

1.6.4 Ground Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1.7 Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1.7.1 Powering Up the Switch Platform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

1.8 InfiniBand QSFP Cable Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

1.8.1 Supported Approved Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

1.8.2 Cable Power Classes. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . 35

1.9 Hot Swap Insertion and Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

1.9.1 Power Supply Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

1.9.2 Leaf Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

1.9.3 Spine Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

1.9.4 Fan Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

1.9.5 Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

1.9.6 Switch Shut-Down Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Chapter 2 Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

2.1 LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

2.1.1 Power Supply Unit LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

2.1.2 Leaf Board LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

2.1.3 Spine Board LED Indicators. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . 54

2.1.4 Spine Side Panel Display LED Indicators . . . .

. . . . . . . . . . . . . . . . . . . . 55

2.1.5 Management Module LED Indicators. .

. . . . . . . . . . . . . . . . . . . . . . . . . . 56

2.1.6 Port Connector Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

2.2 Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.3 QSFP Cable Power Budget Classification. . . . . . . . . . . . . . . . . . . . . . . . 59

2.4 Management Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.4.1 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.4.2 CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.4.3 MGT– Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.4.4 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

2.4.5 Reset – RST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

4

Chapter 3 Chassis Power Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

3.1 Power Supply and Spine Board Indicator Status at Power ON. . . . . . . . 61

Chapter 4 First-Time Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4.1 Running the Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4.2 Re-Running the Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.3 Downloading FabricIT Software and Documents . . . . . . . . . . . . . . . . . . 68

4.4 Installing Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

4.5 Getting and Inserting the License Key. . . . . . . . . . . . . . . . . . . . . . . . . . . 69

4.6 FabricIT Management and Inspection License . . . . . . . . . . . . . . . . . . . . 71

4.7 Starting the Command Line (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.8 Starting the Web User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Chapter 5 Resetting the Switch – RST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Chapter 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

6.1 Power Supply Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

6.2 Leaf Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

6.3 Management Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

6.4 Spine Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

6.5 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Chapter 7 Disassembly and Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

7.1 Disassembling the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

7.1.1 Removing the Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

7.1.2 Removing the Bottom Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

7.2 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Appendix A Installation Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

A.1 Installation Safety Warnings (English) . . . . . . . . . . . . . . . . . . . . . . . . 80

A.2 安裝安全性警告 (Chinese) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

A.3 Avertissements de sécurité pour l'installation (French) . . . . . . . . . . . 89

A.4 Installation Sicherheitshinweise(German). . . . . . . . . . . . . . . . . . . . . . 94

A.5 Advertencias de seguridad de instalación (Spanish) . . . . . . . . . . . . . 98

A.6 Предупреждения по технике безопасности при установке (Russian) 102

A.7 Avertismente privind siguranţa la instalare (Romanian) . . . . . . . . . . 106

A.8 Sigurnosna upozorenja za instaliranje (Croatian). . . . . . . . . . . . . . . 111

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

5

List of Tables

Table 1: Revision History of this User’s Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 2: Reference Documents and Websites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 3: Leaf Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Table 4: Connector Physical and Logical Link Indications

. . . . . . . . . . . . . . . . . . . . . . . . 53

Table 5: Spine Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Table 6: Spine Fan Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Table 7: Spine to Leaf IB Link Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Table 8: LEDs Display for Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 9: LEDs Display for Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 10: Management Module PSU LED Configurations . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 11: Management Module S.Fan LED Configurations . . . . . . . . . . . . . . . . . . . . . . . 58

Table 12: Management Module L.Fan LED Configurations . . . . . . . . . . . . . . . . . . . . . . . 58

Table 13: Management Module MASTER LED Configurations . . . . . . . . . . . . . . . . . . . . 58

Table 14: Serial Terminal Program Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table 15: Configuration Wizard Session - IP Configuration by DHCP. . . . . . . . . . . . . . . . 64

Table 16: Configuration Wizard Session - IP Zeroconf Configuration

. . . . . . . . . . . . . . . . 66

Table 17: Configuration Wizard Session - St

atic IP Configuration. . . . . . . . . . . . . . . . . . . 67

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

6

List of Figures

Figure 1: Shelf Installation Kit Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 2: Chassis Installation Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 3: Shock and Tilt Stickers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 4: Opening the Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 5: Placement of Chassis in Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 6: Inserting the Caged Nuts for the Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 7: Connect Rail Slide to Rack Vertical support . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 8: Inserting the Caged Nuts for the FaceplateChassis on Shelf with F

iller Panel . 24

Figure 9: Cable Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 10: Cable Holder Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 11: Chassis Rails and Rail Slides . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . 27

Figure 12: Installing the Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 13: Screw the Handles Onto the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 14: The Rails are Already Connected Onto the Chassis

. . . . . . . . . . . . . . . . . . . . 29

Figure 15: Raising the Chassis Using a Mechanical Lift

. . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 16: Put on the Rail Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 17: IS5200 Chassis on the Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 18: Face Plate Mounting Bolt Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 19: Ground Connectio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 20: Multiple Power Inlets – Electric Caution Notification . . . . . . . . . . . . . . . . . . . . . 33

Figure 21: Spine Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 22: Power Cord Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 23: PSU Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 24: Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 25: Leaf Board Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Figure 26: Ejector Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Figure 27: Leaf Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 28: Intact vs Defected Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 29: Intact vs Defected Power Pin Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 30: Management Module Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 31: Spine Board Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 32: Intact vs Defected Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 33: Intact vs Defected Side Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 34: Intact vs Defected Middle Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 35: Intact vs Defected Power Pin Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 36: Leaf Fan Locations on the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 37: Leaf Fan Module Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

7

Figure 38: Spine Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 39: Fan Status LED on the Spine Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 40: Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 41: Intact vs Defected Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 42: Intact vs Defected Power Pin Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 43: Power Supply Unit Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 44: PSU Cover On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Figure 45: Leaf Board Led Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 46: Spine Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Figure 47: Spine Side Panel Display Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Figure 48: Management Module Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Figure 49: Management Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Figure 50: Port Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Figure 51: Top and Bottom Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Figure 52: Management Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Figure 53: Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Figure 54: Spine Side Panel Display Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Figure 55: Management Module Status Indications for Normal Operation . . . . . . . . . . . . 62

Figure 56: Console Ports for SX60xx/SX65xx Managed Systems . . . . . . . . . . . . . . . . . . . 63

Figure 57: License Key Entitlement Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Figure 58: License Key Generation Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 59: FabricIT Status/Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 60: MLNX-OS Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Figure 61: EULA Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Figure 62: Display After Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Figure 63: Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

8

Revision History

About this Manual

This manual provides installation and set-up instructions for the IS5200 GT series QSFP

Chassis InfiniBand Switch Platform.

Intended Audience

This manual is intended for users and system administrators responsible for installing

and setting up the chassis platform.

The manual assumes familiarity with the InfiniBand

®

architecture specification.

Table 1 - Revision History of this User’s Manual

Revision Date Details

1.6 Feb. 2014 Rearranged document: Consolidated installation sections under

Chapter 1, “Installation,” on page 10; updated Chapter 1, “Overview,”

on page 12; and re-ordered sections).

Added:

• Figure 49, “Management Module LEDs,” on page 57

Updated:

• Section 1.4, “Power Supply Redundancy,” on page 15

• Section 1.6.1.5, “Installing the Shelf,” on page 21

• Section 1.6.2, “Installing the Cable Holder,” on page 25

• Section 1.9, “Hot Swap Insertion and Extraction,” on page 35

• Section 7.1, “Disassembling the Chassis,” on page 78

• Appendix A, “Installation Safety Warnings,” on page 80

1.5 Sept. 2012

• Added figure11.

• Added information regarding inserting the bottom spine first. Insert spines

from bottom to top.

• Fixed broken links

• Added step to remove plastic covering.

• Added IBM Lift tool

1.4 Aug. 2011 Fixed Installation kit parts

1.3 Oct. 2010 Added air flow direction

1.2 Oct. 2010

• Removed the Chassis Rail from the installation kit and from the installation

instructions.

1.1 Aug. 2010

• Added weight lifting warning

• Added step to Installation procedure

“Remove all protective plastic film from all sides and top of the chassis.”

• Added cable power classes

1.0.1 July 2010

• Added last page with barcode

• Changed Installation procedure to include Remove all FRUs

• Need 4 people to lift

1.0 July 2010 First release

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

9

Related Documentation

The documentation set accompanying the QSFP Chassis InfiniBand Switch platform

includes the following:

Conventions

Throughout this manual, the name IS5200 and the terms chassis and switch are used to

describe the 216 port QSFP InfiniBand chassis, unless explicitly indicated otherwise.

The following icons are used throughout this document to indicat

e information that is

important to the user.

Table 2 - Reference Documents and Websites

Document Name Description

InfiniBand Architecture Specification,

Vol. 1, Release 1.2.1

The InfiniBand Architecture Specification that is provided by

IBTA

Switch Product Release Notes For possible hardware issues see the switch support product

page.

This requires a customer support login. Look up the rele-

vant SwitchX®-based switch system/se

ries release note file.

Mellanox MLNX-OS® User Manual

for

VPI

This document contains information regarding configuring and

managing Mellanox Technologies SwitchX® switch platforms

listing all of the commands available through MLNX-OS with

explanations and examples.

This symbol makes recommendations to the user.

This symbol indicates information that is helpful to the user.

This symbol indicates a situation that can potentially cause damage to hardware or

software.

Warning! This symbol indicates a situation that can potentially cause personal injury

and / or damage to hardware or software.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

10

1Installation

Installation and initialization of the chassis is a simple process requiring attention to the

normal mechanical, power, and thermal precautions for rack-mounted equipment. Your

Chassis will be shipped in two packages one with the all of the leafs (leaf package) that

are ordered and an extra management module should it be ordered, and the second pack-

age (chassis package) with all of

the rest of the parts.

The chassis requires initial configuration

to get the chassis and Fabric management up

and running through remote management. See the Installation Guide that is packed in the

box for the instructions to make the initial configuration.

1.1 Installation Safety Warnings

These safety warnings are in English. For French, German, Spanish, Russian, and Roma-

nian see the Appendixes.

1. Installation Instructions

2. Bodily Injury Due to Weight

3. Heavy Equipment

This chassis can be installed in standard 19” racks that have depths between 65cm and

80cm between the vertical supports of the rack.

This unit is intended for installation in a Restricted Access Location. A restricted

access area can be accessed only through the use of a special tool, lock and key, or

other means of security.

Read all installation instructions before connecting the equipment to the power source.

Use enough people to safely lift this product.

This equipment is very heavy and should be moved using a mechanical lift to avoid

injuries.

<40 lbs

<18 kgs

40 - 70 lbs

18 - 32 kgs

70 - 121 lbs

32 - 55 kgs

>121 lbs

>55 kgs

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

11

4. Installation in Restricted Access Location

5. Risk of Electric Shock!

6. Over-temperature

7. Stacking the Chassis

8. Redundant Power Supply Connection - Electrical Hazard

9. Double Pole/Neutral Fusing

10. Multiple Power Inlets ,

This unit is intended for installation in a Restricted Access Location.

Risk of Electric Shock!

With the fan module removed power pins are accessible within the module cavity.

DO NOT insert tools or body parts into the fan module cavity.

This equipment should not be operated in an area with an ambient temperature exceed-

ing the maximum recommended: 45°C (113°F). Moreover, to guarantee proper air

flow, allow at least 8cm (3 inches) of clearance around the ventilation openings.

The chassis should not be stacked on any other equipment. If the chassis falls, it can

cause bodily injury and equipment damage.

This product includes a redundant power or a blank in its place. In case of a blank

power supply, do not operate the product with the blank cover removed or not securely

fastened.

This system has double pole/neutral fusing. Remove all power cords before opening

the cover of this product or touching any internal parts.

Risk of electric shock and energy hazard.

The PSUs are all independent.

Disconnect all power supplies to ensure a powered down state inside of the switch

platform.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

12

11. During Lightning - Electrical Hazard

12. Copper InfiniBand Cable Connecting/Disconnecting

13. Rack Mounting and Servicing

14. Equipment Installation

15. Equipment Disposal

16. Local and National Electrical Codes

17. Installation Codes

During periods of lightning activity, do not work on the equipment or connect or dis-

connect cables.

Copper InfiniBand cables are heavy and not flexible, as such they should be carefully

attached to or detached from the connectors. Refer to the cable manufacturer for spe-

cial warnings/instructions.

When this product is mounted or serviced in a rack, special precautions must be taken

to ensure that the system remains stable. In general you should fill the rack with equip-

ment starting from the bottom to the top.

This equipment should be installed, replaced, and/or serviced only by trained and qual-

ified personnel.

Disposal of this equipment should be in accordance to all national laws and regula-

tions.

This equipment should be installed in compliance with local and national electrical

codes.

This device must be installed according to the latest version of the country

national electrical codes. For North America, equipment must be installed in

accordance to the applicable requirements in the US National Electrical Code

and the Canadian Electrical Code.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

13

18. Battery Replacement

19. UL Listed and CSA Certified Power Supply Cord

20. High Leakage Current

21. Add GND connection information

22. Installation codes

23. Interconnection Of Units

Warning: Replace only with UL Recognized battery, certified for maximum

abnormal charging current not less than 4mA

There is a risk of explosion should the battery be replaced with a battery of an

incorrect type.

Dispose of used batteries according to the instructions.

For North American power connection, select a power supply cord that is UL Listed

and CSA Certified, 3 - conductor, [16 AWG], terminated with a molded plug rated at

125 V, [13 A], with a minimum length of 1.5m [six feet] but no longer than 4.5m.

For European connection, select a power supply cord that is internationally

harmonized and marked “<HAR>”, 3 - conductor, minimum 1.0 mm

2

wire,

rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug

rated at 250 V, 10 A.

Warning: High leakage current; Earth connection essential before connecting supply.

Before connecting this device to the power line, the protective earth terminal screws of

this device must be connected to the protective earth in the building installation.

(GND Connection Information):

The building installation shall provide a means for a connection to protective earth;

and the equipment shall be permanently connected to that by a service person.

A SERVICE PERSON shall check whether or not the socket - outlet from which the

equipment is to be powered provides a connection to the building protective earth. If

not, the SERVICE PERSON shall arrange for the installation of a PROTECTIVE

EARTHING CONDUCTOR from the separate protective earthing terminal to the pro-

tective earth wire in the building. The equipment shall be installed in area where equi-

potential bonding exists ((such as a telecommunication centre or a dedicated computer

room).

This device must be installed according to the latest version of the country national

electrical codes. For North America, equipment must be installed in accordance to the

applicable requirements in the US National Electrical Code and the Canadian Electri-

cal Code.

Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL

certified type DP-1 or DP-2. (Note- when residing in non LPS circuit)

Overcurrent Protection: A readily accessible Listed branch circuit overcurrent

protective device rated 20 A must be incorporated in the building wiring.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

14

24. Hazardous Radiation Exposure

25. Proper Enclosure

26. Do Not Use the Switch as a Shelf or Work Space

27. WEEE Directive

28. Country of Norway Power Restrictions

1.2 Environmental and Safety Recommendations

The following are Mellanox recommendations.

Caution – Use of controls or adjustment or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

CLASS 1 LASER PRODUCT and reference to the most recent laser standards

IEC 60 825-1:1993 + A1:1997 + A2:2001 and EN 60825-1:1994+A1:1996+

A2:2001

A suitable electrical, mechanical and fire enclosure shall be provided by the end prod-

uct manufacturer and or the end user.

Caution: Slide/rail mounted equipment is not to be used as a shelf or a work space. The

rails are not intended for sliding the unit away from the rack. It is for permanent instal-

lation at final resting place only, not used for service and maintenance

According to the WEEE Directive 2002/96/EC, all waste electrical and electronic

equipment (EEE) should be collected separately and not disposed of with regular

household waste.

Dispose of this product and all of its parts in a responsible and environmentally

friendly way.

This unit is intended for connection to a TN power system and an IT power system of

Norway only.

Recommended ambient temperature in the System room is 20

o

± 5

o

C.

Recommended humidity range is 40% ± 15% without condensing.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

15

1.3 Chassis Package Contents

The package includes:

• 1 box containing

• installation kit parts

• cable management system

•power cords

• 1 shelf

• 1 chassis with the following modules inst

alled:

• 1 shelf

•6 spines

• 1 management module

•4 fans

• 4 PSUs

If you are not using a mechanical lift to install the chass

is, reduce the weight of the chas-

sis by removing all of the spines, power su

pply units, management modules, and fan

units, and put aside for reinstallation after the chassis is installed in the rack.

• 1 installation guide

• 1 box containing various other parts

It is highly recommended that the installation sites be as isolated as possible from all

sources of radio transmissions and electrical interference.

It is highly recommended that the installation site building be equipped with a light-

ning rod.

It is highly recommended that the installation site be equipped with smoke detectors

and a fire alarm warning system.

The system requires a KVA rated UPS system. It is recommended that a UPS system

be installed to protect the equipment in the event of unexpected power failure.

Make sure that the outlets and circuits will not be overloaded. Spread out the load over

at least two or three circuits or use a 3 phase circuit.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

16

Inside the single box is 3 smaller boxes.

• 1 installation kit box

•

1 box containing 4 power cords 250v 15a 2.0M, C14 to C13, USA UL Standard

• 1 cable management kit

Before you install your new IS5200 series chassis, unpack the s

ystem and check to make

sure that all the parts have been sent, check this against the parts list. Check the parts for

visible damage that may have occurred during shipping.

1.4 Leaf Package Contents

The leafs are ordered by the customer and are shipped 4 to a box. The customer will

receive as many boxes as needed to fill the order.

1.5 Management Package Contents

When a second management module is ordered the package includes:

• 1 management module ordered by the customer

•

1 RJ45 to DB9 harness

1.6 Physical Installation

The switch platform uses 10U of rack space in a standard 19” rack, 9U for the chassis

and 1U for the shelf. The switch ships from the factory with mounting holes on the spine

side. There are upper brackets to connect the leaf side to the rack near the top of the chas-

sis. The weight of the switch is support

ed from underneath the unit by the shelf.

If anything is damaged or missing, contact your customer representative immediately.

The rack mounting holes conform to the EIA-310 standard for 19-inch racks. Guaran-

tee proper ventilation, by leaving 8cm (3”) of space to the front and rear of the switch.

This will ensure proper air flow through the chassis. This is crucial for maintaining

good airflow at ambient temperature. In particular, route cables such that they do not

impede the air into or out of the chassis.

Warning: This equipment is very heavy. Safety is the first concern. Make sure that

adequate manpower and proper equipment is used for transporting and moving the

chassis.

The fully loaded chassis weighs:

120 kg (265 LBS) full configuration

48 KG (105 LBS) empty configuration

83.94kg (185 LBS) shipped configuration

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

17

This chassis can be installed in standard 19” racks that have between 65cm and 80cm

between the vertical supports of the rack. Make sure that a fully populated rack including

cables will have sufficient air flow for cooling.

1.6.1 ESD Connection

Before starting any procedure on the IS5200 switch system:

1. Put an ESD prevention wrist strap on your wrist, and

make sure there is good contact

between your body and the strap.

2. Plug the other end of the wrist strap to a valid

ground. Make sure that this is a tight

fit.

1.6.1.1

Installation ProcedureRequirements

You will need:

Choose a rack which is able to support the mechanical and environmental characteris-

tics of a fully populated switch chassis.

Mellanox recommends a rack that is at least 80 cm long.

• #2 phillips screwdriver • #3 phillips screwdriver

• a grounding lug • ground wire to properly ground the chassis

The installation will be much easier with a power screwdriver.

It is recommended to use AWG6 or 4mm diameter wire for grounding purposes.

It is recommended to have at least two people for the duration of the installation proce-

dure. Use a mechanical lift to raise this chassis. If not, use enough manpower to ensure

the safety and wellbeing of all of the people involved in the installation.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

18

1.6.1.2 Installation and Cable Management Kit Parts

Parts for installing the shelf

Parts for installing the chassis

Parts for installing the filler panel

Parts for installing the cable manager

You will need 10 U of space in the rack. Nine U for the chassis and one

U for the shelf.

Figure 1: Shelf Installation Kit Parts

•1 shelf • 8 M6 bolts for the caged nuts

• 4 caged nuts • 2 Shelf rail slides

• 4 lock washers • 2 long 2 hole flat washers

• 2 chassis rail slides • 4 handles

• 8 M-5 pan head bolts • 8 allen head screws

• 2 flat 4 hole metal spacers • 1 allen wrench

• 8 lock washers • 4 lock nuts for handles (These nuts are not to be used)

• 8 caged nuts for the faceplate • 8 M6 bolts for the caged nuts, 8 for the faceplate

• 1 Bottom filler panel • 2 M6 bolts

• 2 caged nuts M6

• 1 RH cable holder • 1 LH cable holder

• 12 caged nuts M6 • 12 M6 bolts

• 6 cable holder shelves

Shelf

Rail

Rail Slide

Angled

Bracket

M6 X 12 bolts, caged nuts and

split lock washers

M6 X 16

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

19

Figure 2: Chassis Installation Parts

1.6.1.3 Container Mishandling

The container has shock and tilt stickers applied. These will turn

red if the container has

been mishandled or roughly handled. Upon receipt of the container look for and inspect

the shock and tilt stickers to confirm that they have not tripped. If one or more are red

notify the shipper and Mellanox. This on its own does not indicate damage to the con-

tents. But, be sure to carefully inspect

the contents if any of the shock and tilt stickers

have tripped.

Rail Slide

Screws for

the handles

M-5 Pan head

screws and

lock washers

4 hole Washer

Handles

Caged nuts

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

20

Figure 3: Shock and Tilt Stickers

1.6.1.4 Opening the Container

1. Before starting the procedure, put the ESD strap on and connect it to a valid ground.

2. Open the crate by unscrewing the sides and top of the crate.

HANDLE WITH CAREHANDLE WITH CARE

GGIINN NNRRWWAA

GG

II

NN NNRRWWAA

HANDLE WITH CAREHANDLE WITH CARE

GG

II

NN NNRRWWAA

GG

II

NN NNRRWWAA

TIL TWA

T

CH

TIL TWA

T

CH

Stickers unaffected by

shipping

Stickers showing excessive

shock or tilt.

Pagina se încarcă ...

Mellanox Technologies MIS5200Q-4DNC Hardware Installation Manual

Acest manual este potrivit și pentru

Mellanox Technologies MIS5200Q-4DNC Hardware Installation Manual

în alte limbi

Lucrări conexe

Alte documente