Silvercrest SLS 2200 A1 Manual de utilizare

V 1.16

English ................................................................................. 2

Ελληνικά ........................................................................... 19

Română ............................................................................. 37

Български ......................................................................... 54

Deutsch .............................................................................. 71

SilverCrest SLS 2200 A1

2 - English

Table of Contents

Trademarks .............................................................................. 3

Introduction .............................................................................. 3

Intended use ............................................................................. 3

Package contents ..................................................................... 4

Technical specifications ............................................................. 5

Safety instructions .................................................................... 6

Maintenance / cleaning ............................................................ 8

Copyright ................................................................................. 9

Overview of controls and button functions ............................. 10

Before you start ..................................................................... 11

Fitting the suction pads ..................................................................................... 11

Charging using the solar panel ....................................................................... 12

Charging via the USB cable ............................................................................ 12

Getting started ....................................................................... 13

Using the ON/OFF pushbutton ....................................................................... 13

Viewing the battery level .................................................................................. 13

Compatible devices .......................................................................................... 13

Charging devices .............................................................................................. 14

Troubleshooting ..................................................................... 15

Environmental regulations and disposal information ............. 16

Conformity notes .................................................................... 16

Warranty and Service Information ......................................... 17

SilverCrest SLS 2200 A1

English - 3

Trademarks

Apple

®

, iPhone

®

, iPad

®

and iPod

®

are trademarks of Apple Inc., and are

registered in the USA and in other countries.

USB is a registered trademark.

Other names and products can be the trademarks or registered trademarks of

their respective owners.

Introduction

Thank you for choosing the SilverCrest SLS 2200 A1 Solar Battery Charger.

The Solar Battery Charger can convert sunlight into electrical energy and store

it. This allows you to charge a mobile phone, an MP3 player or a digital

camera when you are on the move without access to a wall socket.

Intended use

This is an information technology product and has been designed to charge the

batteries installed in mobile phones, MP3 players, digital cameras or other

battery-powered devices. The Solar Battery Charger converts sunlight into

electrical power and stores it into the built-in battery. The device may only be

used for private purposes, not for industrial or commercial ones. The device

may also not be used in tropical climates. The manufacturer is not liable for any

damage or problems caused by unauthorised modifications. Only use

accessories recommended by the manufacturer. Observe the regulations and

laws in the country of use.

SilverCrest SLS 2200 A1

4 - English

Package contents

A SilverCrest SLS 2200 A1 Solar Battery Charger

B USB cable

C Charger cable

D "USB socket" adapter [5V]

E Sony PSP* adapter [5V; compatible devices poss. 7.5V/9.5V]

F Nokia 6101* adapter [5V; compatible devices poss. 7.5V/9.5V]

G "Micro USB" adapter [5V]

H "Mini USB" adapter [5V]

I Samsung A288* adapter [5V]

J iPhone

®

/ iPad

®

/ iPod

®

adapter (30‑pin)* [5V]

K Siemens S65* adapter [5V]

L Nokia 8210* adapter [5V; compatible devices poss. 7.5V/9.5V]

M LG K690 / Chocolate* adapter [5V]

N Sony Ericsson K750* adapter [5V]

O Suction pads (4 units)

P These operating instructions (line-art illustration)

* and compatible devices with up to 500mA charging current

SilverCrest SLS 2200 A1

English - 5

Technical specifications

Solar module

 Power

 Dimensions (W x H)

5.0V / 100mA

approx. 6 x 10.6 cm

Rechargeable Li-Ion battery 3.7V / 2200mAh

Input voltage/current (USB) 5.0V / 0.5A

Output voltage/current  5.0V +/–- 5%, 0.5A

 7.5V +/– 5%, 0.5A

 9.5V +/– 5%, 0.5A

Charging time for built-in Li-Ion

battery

 Via solar panel

 PC adapter

approx. 16-24 hours*

approx. 4-6 hours

Dimensions (W x H x D) approx. 70 x 129 x 20mm

Weight (without accessories) approx. 118g

Operating temperature 5C to 45C

Operating humidity max. 85% rel. humidity

(non-condensing)

Storage conditions -5C to +50C

max. 85% rel. humidity

(non-condensing)

* The charging time varies greatly depending on the sun's radiation (intensity).

This depends on the season, the cloud cover and the location. These factors

may also increase the charging time.

The technical specifications and design can be changed without prior notice.

SilverCrest SLS 2200 A1

6 - English

Safety instructions

Before you use this device for the first time, please read the following notes in

this manual and heed all warnings, even if you are familiar with handling

electronic devices. Keep this manual in a safe place for future reference. If you

sell the device or pass it on, it is essential that you also hand over this manual,

as it is part of the product.

WARNING! This symbol denotes important information for

the safe operation of the product and user safety. Ignoring it

can lead to material damage and/or personal injury or even

death.

This symbol denotes further information on the topic.

Operating environment

The device is not designed for use in environments with high humidity (e.g.

bathrooms) or excessive levels of dust. Operating temperature and operating

humidity: 5 ºC to 45 ºC, max. 85 % RH. Please note that when using the

product in a car, especially behind the windscreen, the temperature can reach

above 45C.

Always make sure that

 the device is not exposed to direct heat sources (e.g. radiators)

 the device is not exposed to strong artificial light

SilverCrest SLS 2200 A1

English - 7

 contact with water spray and drops and aggressive fluids is avoided and the

device is never operated near water, the device is never submerged (do not

place any items containing liquids, such as drinks, vases, etc. on or near the

device).

 the device is never placed near magnetic fields (e.g. speakers)

 no naked flames (e.g. burning candles) are placed on or near the device

 no foreign bodies can penetrate into the device

 the device is not subjected to any major temperature fluctuations as this can

cause condensation and short-circuiting. If the device has been exposed to

strong temperature fluctuations, wait for it to reach the ambient temperature

before switching it on (about 2 hours).

 the device should not be subject to excessive shocks and vibrations

 the device or the optional USB power adapter is not used during

thunderstorms and unplug the optional USB power adapter from the mains

 when using a USB power adapter the power socket used must be easily

accessible at all times and cables are laid so they do not present a trip

hazard

 the device is not covered

Failure to heed the warnings above may result in damage to the device or

injury.

Caution – danger of explosion

Never throw the device onto a fire and do not invert the battery polarity or

short-circuit the battery, as this could cause it to explode.

Please note the usage restrictions and regulations relating to battery-powered

devices in dangerous places, such as petrol stations, aircraft, hospitals, etc.

SilverCrest SLS 2200 A1

8 - English

Children and persons with disabilities

Electrical devices are not suitable for children. Also persons with reduced

physical, sensory or mental capabilities should only use electrical devices in

appropriate circumstances. Do not allow children or persons with disabilities to

use electrical devices unsupervised, unless they are instructed accordingly and

supervised by a competent person responsible for their safety. Children should

always be supervised to ensure that they do not play with the product. Small

parts can represent choking hazards. Keep the packaging away from children

and persons with disabilities.

There is a risk of suffocation!

Cables

Unplug all cables by holding the plugs and never pull on the cables

themselves. Never place pieces of furniture or other heavy objects on the

cables and take care that they do not become damaged, especially at the

plugs and sockets. Never tie knots in a cable and do not tie them to other

cables. All cables must be laid so that nobody can trip over them or be

obstructed by them.

Maintenance / cleaning

Repairs are required if this device has been damaged in any way, for example

if the device housing is damaged, if liquids or objects have penetrated the

SilverCrest SLS 2200 A1

English - 9

device or if the product has been exposed to rain or moisture. Repairs are also

necessary if the product is not working properly or has been dropped. If you

notice any smoke, unusual noises or strange smells, unplug all cables

immediately and disconnect the optional USB power adapter from the power

supply. If this occurs, do not continue to use the device and have it checked out

by an expert. All repairs must be carried out by qualified service personnel.

Never open the housing of the device. Only use a clean, dry cloth for cleaning.

Never use aggressive liquids. Do not attempt to open the housing of the

device, this will void your warranty.

Copyright

All the contents of this user manual are protected by copyright and provided to

the reader for information only. Copying data and information without the prior

explicit written consent of the author is strictly forbidden. This also applies to

any commercial use of the contents and information. All texts and diagrams are

up-to-date as of the date of printing.

SilverCrest SLS 2200 A1

10 - English

Overview of controls and button functions

An illustration of the items and controls and their corresponding numbers can

be found on the inside page of the fold-out cover of this user manual. You can

keep this page folded out whilst reading the different chapters of this user

manual. This allows you to refer to the relevant controls at any time.

1 Solar panel

2 Output voltage selector switch (5V, 7.5V or 9.5V)

3 Output voltage LEDs

4 DC-OUT socket (to connect the device to be charged)

5 Solar LED

6 ON/OFF pushbutton

7 Battery capacity LEDs

8 IN socket (to connect a PC or USB power adapter)

SilverCrest SLS 2200 A1

English - 11

Before you start

Remove the solar battery charger and the accessories from the packaging.

Fitting the suction pads

Fix the four suctions pads (O) to the bottom of the solar battery charger as

shown in the diagram below. Insert the suction pads (O) into the hole. Next, fix

the suction pads (O) by sliding them into the smaller hole.

You can now mount the solar battery charger to a flat, even surface using the

suction pads.

The surface should be free of dust, oil and grease for the

suction pads to stick well.

SilverCrest SLS 2200 A1

12 - English

Charging using the solar panel

Make sure that the maximum ambient temperature of +45C is

not exceeded. This is especially important if you are using the

product in a car.

You can charge the built-in battery of the solar charger using the solar panel

(1). Make sure that the solar panel (1) receives sufficient sunlight. As soon as

there is enough sunlight, the Solar LED (5) goes orange to indicate that the

battery is being charged. If the Solar LED (5) does not light up, there is not

enough sunlight. In this case, move the device to a different position or place it

in direct sunlight. When the Solar LED (5) goes green, the battery is fully

charged.

Charging via the USB cable

If there is no sunlight, you can also charge the built-in battery in your Solar

Battery Charger using the USB cable (B). Insert the smaller plug of the USB

cable (B) into the IN socket (8) of your Solar Battery Charger. Then insert the

USB plug of the USB cable (B) into a USB port on your computer. You can

monitor the charging process using the Battery capacity LEDs (7). One of the

Battery capacity LEDs (7) flashes during charging and indicates the status of

the battery charging process. When all four Battery capacity LEDs (7) are lit,

the battery is fully charged.

Some computers do not supply USB power while they are

turned off. If the battery of your Solar Battery Charger does not

charge, make sure your computer is powered on.

Alternatively, you can use an external USB power adapter (not

supplied) to charge the battery of your solar battery charger.

To do this, you will need the USB cable (B) supplied. You can

SilverCrest SLS 2200 A1

English - 13

purchase a suitable 5V USB power adapter with at least

500mA from any electronics retail outlet.

When using an external power adapter, it must be connected

to an easily accessible wall outlet so that it can be disconnected

quickly in case of an emergency.

Getting started

Using the ON/OFF pushbutton

Powering on

Briefly press the ON/OFF pushbutton (6) to switch the Solar Battery Charger

on. The output voltage LEDs (3) and the battery capacity LEDs (7) light. After

approx. 5 seconds the battery capacity LEDs (7) go off, and the output voltage

LEDs (3) light while a connected device is being charged.

Auto power off

If no device to be charged is connected within 20 seconds, the device will

power off to safe battery power.

Powering off

Keep the ON/OFF pushbutton (6) pressed for at least 3 seconds to switch the

Solar Battery Charger off and to cancel the current charging process.

Viewing the battery level

Press the ON/OFF pushbutton (6) briefly to display the battery level for a few

seconds. The Battery capacity LEDs (7) indicate the battery level as a

percentage (25%, 50%, 75% and 100%).

Compatible devices

The Solar Battery Charger can be used to charge external devices with a max.

charging current of 500mA.

If the charging current of your connected device exceeds 500mA, the Solar

Battery Charger will automatically power off after you turn it on with the

SilverCrest SLS 2200 A1

14 - English

ON/OFF pushbutton (6). In this case, double-check the external device

compatibility by reading its technical specifications (operating instructions).

Charging devices

First, select the correct output voltage. Slide the output voltage selector switch

(2) to the desired position. You can set the following voltages: 5V, 7.5V and

9.5V. If you are not sure what voltage the device requires, read the manual for

it.

Setting the wrong voltage could damage the device! Double-

check the output voltage set before connecting the device! To

do this, press the ON/OFF pushbutton (6) briefly. The voltage

set is displayed for a few seconds. You can check the voltage

set (5V, 7.5V or 9.5V) using the Output voltage LEDs (3). Wait

until the Output voltage LEDs (3) go out.

After you have set and checked the proper output voltage, you can connect the

external device using the charger cable (C) and the required adapter (D to N).

Plug the adapter required (D to N) onto the charger cable (C). The "Package

contents" chapter includes an overview of the adapters supplied. Next, connect

the charger cable (C) to the DC-OUT socket (4) of the Solar Battery Charger

and the adapter connected (D to N) to your external device.

Using the wrong voltage can damage your device!

Now press the ON/OFF pushbutton (6) briefly to start the charging process.

Then the output voltage LEDs (3) light while the connected device is being

charged. When your external device is fully charged, the Solar Battery

Charger switches off. To cancel the charging process at any time, simply

disconnect the external device. If your external device is not fully charged but

the Output voltage LEDs (3) go out during charging, the built-in battery of your

Solar Battery Charger is empty. You will need to recharge your Solar Battery

SilverCrest SLS 2200 A1

English - 15

Charger in order to charge external devices. You can recharge the built-in

battery of your solar charger and charge the external device at the same time.

Troubleshooting

A connected device is not charging.

 Press the ON/OFF pushbutton (6) briefly to start the charging process.

 The battery of your solar charger is empty, recharge it.

 No connection to the external device, double-check the connection.

 The “Micro USB” adapter (G) you are using is not compatible with the

device you want to charge. Use the original charging cable of your device

together with the “USB socket” adapter (D).

 The Solar Battery Charger LEDs do not light up. Connect the Solar Battery

Charger to a computer or an external power supply for approx. 2

seconds to reset the built-in overload protection.

 The Solar Battery Charger can be used to charge external devices with a

max. charging current of 500mA. If the charging current of your

connected device exceeds 500mA, the Solar Battery Charger will

automatically power off after you turn it on with the ON/OFF pushbutton

(6). In this case, double-check the external device compatibility by reading

its technical specifications (operating instructions).

Cannot charge the battery of the solar charger using the solar

panel.

 Make sure that the solar panel (1) is receiving enough sunlight.

Cannot charge the battery of the solar charger via the USB

cable.

 Faulty connection, double-check the connection.

SilverCrest SLS 2200 A1

16 - English

 Some computers do not supply USB power while they are turned off. If the

battery of your Solar Battery Charger does not charge, make sure your

computer is powered on.

Environmental regulations and disposal

information

Devices marked with this symbol are subject to the European

Directive 2012/19/EU. All electrical and electronic devices

must be disposed of separately from household waste at

official disposal centres. Proper disposal of old devices

prevents damage to the environment or your health. For

further information about proper disposal, contact your local

council, recycling centre or the shop where you bought the

device.

The built-in rechargeable battery cannot be removed for

disposal.

Dispose of all packaging in an environmentally-friendly manner. Cardboard

packaging can be taken to paper recycling centres or public collection points

for recycling. Any film or plastic contained in the packaging should be taken to

your public collection points for disposal.

Conformity notes

This device complies with the basic and other relevant

requirements of EMC Directive 2004/108/EC and the

RoHs Directive 2011/65/EU. The Declaration of

Conformity can also be found at the end of this Manual.

SilverCrest SLS 2200 A1

English - 17

Warranty and Service Information

Warranty of TARGA GmbH

This device is sold with three years warranty from the date of purchase. Please

keep the original receipt in a safe place as proof of purchase. Before using

your product for the first time, please read the enclosed documentation. Should

any problems arise which cannot be solved in this way, please call our hotline.

Please have the article number and, if available, the serial number to hand for

all enquiries. If it is not possible to solve the problem on the phone, our hotline

support staff will initiate further servicing procedures depending on the fault.

Within the warranty period the product will be repaired or replaced free of

charge as we deem appropriate. No new warranty period commences if the

product is repaired or replaced. Consumables such as batteries, rechargeable

batteries and lamps are not covered by the warranty.

Your statutory rights towards the seller are not affected or restricted by this

warranty.

SilverCrest SLS 2200 A1

18 - English

Service

Phone: 0207 – 36 50 744

E-Mail: [email protected]

Phone: 01 – 242 15 83

E-Mail: [email protected]

Phone: 800 – 62 175

E-Mail: [email protected]

Phone: 800 – 92 496

E-Mail: [email protected]

IAN: 94118

Manufacturer

TARGA GmbH

Coesterweg 45

59494 SOEST

GERMANY

Pagina se încarcă ...

Silvercrest SLS 2200 A1 Manual de utilizare

Silvercrest SLS 2200 A1 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente