Silvercrest SLS 2200 C2 Operating Instructions Manual

SOLAR CHARGER SLS 2200 C2

SOLAR CHARGER

Operating instructions

ÎNCĂRCĂTOR SOLAR

Instrucţiuni de utilizare

IAN 273516

SOLARLADEGERÄT

Bedienungsanleitung

ΗΛΙΑΚΗ ΣΥΣΚΕΥΗ ΦΟΡΤΙΣΗΣ

Οδηүίες χρήσης

GB / CY Operating instructions Page 1

RO Instrucţiuni de utilizare Pagina 21

GR / CY Οδηүίες χρήσης Σελίδα 41

DE / AT / CH Bedienungsanleitung Seite 61

Before reading, unfold the page containing the illustrations and familiarise

yourself with all functions of the device.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile

aparatului.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικει-

ωθείτε με όλες τις λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen

Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

GB

│

CY

│

1 ■

SLS 2200 C2

Contents

Introduction .................................2

Information concerning these operating instructions .........2

Copyright ..........................................2

Notes on trademarks .................................2

Intended use ........................................3

Warnings used ......................................3

Safety .....................................4

Basic safety guidelines ................................4

Description of components ....................7

Operation ..................................7

Unpacking .........................................7

Check the package contents ...........................8

Disposal of packaging materials ........................8

Attaching the suction cups .............................9

Charging with the solar panel .........................11

Charging with the USB cable ..........................12

Handling and operation ......................13

Switch the device on/oﬀ .............................13

Display charge level .................................13

Compatible devices .................................14

Charging external devices ............................14

Troubleshooting ............................15

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Storage when not in use .....................16

Disposal ...................................17

Appendix ..................................18

Technical data .....................................18

Notes on the Declaration of Conformity .................19

Warranty .........................................19

Service ...........................................20

Importer ..........................................20

■ 2

│

GB

│

CY

SLS 2200 C2

Introduction

Information concerning these operating

instructions

Congratulations on the purchase of your new device.

You have selected a high-quality product. The operating instructions

are part of this product. They contain important information about

safety, usage and disposal. Before using the product, familiarise

yourself with all operating and safety instructions. Use the product

only as described and for the speciﬁed areas of application.

Keep these operating instructions as a reference and store them

near the product. Please also pass on these operating instructions

to any future owner.

Copyright

This documentation is protected by copyright.

Any copying or reproduction, including in the form of extracts, or

any reproduction of images (even in a modiﬁed state), is permitted

only with the written authorisation of the manufacturer.

Notes on trademarks

USB

®

is a registered trademark of USB Implementers Forum, Inc.

All other names and products may be trademarks or registered

trademarks of their respective owners.

GB

│

CY

│

3 ■

SLS 2200 C2

Intended use

This information technology device is designed solely for the charg-

ing of batteries in mobile phones, MP3 players, digital cameras

or other battery-powered devices. To do this, the device converts

sunlight into electrical energy and stores it in its internal battery. The

device is not intended for any other purpose, nor for use beyond

the scope described. The device is not intended for use in com-

mercial or industrial environments. The manufacturer accepts no

responsibility for damage caused by failure to observe these instruc-

tions, improper use or repairs, unauthorised modiﬁcations or the use

of unapproved replacement parts. The risk shall be borne solely by

the user.

Warnings used

The following warning notice types are used in these operating

instructions:

DANGER

A warning notice at this hazard level indicates a

potentially hazardous situation.

Failure to avoid this hazardous situation could result in severe

injuries or even death.

► Follow the instructions in this warning notice to avoid the risk

of death or serious injury.

■ 4

│

GB

│

CY

SLS 2200 C2

CAUTION

A warning notice at this hazard level indicates a

potential for property damage.

Failure to avoid this situation could result in property damage.

► Follow the instructions in this warning notice to prevent

property damage.

NOTE

► A note provides additional information that will assist you in

using the device.

Safety

This section contains important safety instructions for using the

product. This product complies with statutory safety regulations.

Improper use may result in personal injury and property damage.

Basic safety guidelines

To ensure safe operation of the product, follow the safety guide-

lines set out below:

■ This device may be used by children aged 8 years and above

and by persons with limited physical, sensory or mental capabil-

ities, or lack of experience and knowledge, provided that they

are under supervision or have been told how to use the device

safely and are aware of the potential risks. Children must not

use the device as a plaything. Cleaning and user maintenance

tasks may not be carried out by children unless they are super-

vised.

GB

│

CY

│

5 ■

SLS 2200 C2

■ Check the device for visible external damage before use.

Do not operate a device that has been damaged or dropped.

■ Do not expose the device to water spray or dripping water,

and do not place liquid-ﬁlled objects such as vases or open

drink containers on or near the device.

■

DANGER! Be sure to provide suﬃcient air circulation to

avoid a heat build-up. Never cover the device! Risk of ﬁre!

■ Never operate the device in the vicinity of naked ﬂames

(e.g. candles), and do not place burning candles on or next

to the device. This will help to prevent ﬁres.

■ Do not operate the device near heat sources such as radiators

or other heat-generating devices.

■ Never expose the device to extreme heat. This particularly

applies to storage in a car. Extreme temperatures can occur in

car interiors and glove compartments during long periods of

immobilisation. Remove electrical and electronic devices from

the vehicle.

■

DANGER! Never open the housing of the device.

There are no user-serviceable or replaceable components

inside the device.

■ Do not make any unauthorised modiﬁcations or alterations to

the device.

■ All repairs must be carried out by authorised specialist com-

panies or by the Customer Service department. Improper repairs

may put the user at risk. It will also invalidate any warranty

claims.

■ 6

│

GB

│

CY

SLS 2200 C2

■ Repairs to the device during the warranty period may only be

carried out by a customer service department authorised by

the manufacturer. Otherwise, no warranty claims will be held

for any subsequent damages.

■ Switch the device oﬀ immediately and disconnect any con-

nected charging cables from the device if you smell fumes or

notice any smoke. Have the device checked by a qualiﬁed

specialist before using it again.

■ If you are using a USB power supply, the mains socket used

must always be easily accessible so that the USB power supply

can be quickly disconnected from the socket in a hazardous

situation. You should also observe the operating instructions

for the USB power supply.

■

DANGER! Mishandling the batteries can cause ﬁres, explo-

sions, leakages or other hazards! Do not throw the device into

a ﬁre, since the integrated battery may explode.

■ Comply with all conditions for and prohibitions on use for

battery-powered devices in locations with speciﬁc hazard risks,

such as petrol stations, aeroplanes, hospitals, etc.

■

DANGER! Do not allow children to play with the packaging

material! Keep all packaging materials away from children.

Risk of suﬀocation!

GB

│

CY

│

7 ■

SLS 2200 C2

Description of components

(See fold-out page for illustrations)

Solar panel

Solar LED

LED (5V USB active output)

ON/OFF button

Charge level LEDs

USB port (output: 5 V , 1000 mA)

Micro-USB port (input: 5 V , 500 mA)

Brackets for suction cups

Suction cups

USB cable (USB to micro-USB)

Operating instructions

Operation

Unpacking

♦ Remove all parts and the operating instructions from the

packaging.

♦ Remove all packaging material.

■ 8

│

GB

│

CY

SLS 2200 C2

Check the package contents

(See fold-out page for illustrations)

The product includes the following components:

▯ Solar charger SLS 2200 C2

▯ USB cable

▯ 2 x brackets for suction cups

▯ 4 x suction cups

▯ These operating instructions

NOTE

► Check the package for completeness and for signs of visible

damage.

► If the delivery is incomplete or damage has occurred as a

result of defective packaging or during transport, contact

the Service hotline (see section Service).

Disposal of packaging materials

The packaging protects the device from damage during transport.

The packaging materials have been selected for their environmental

friendliness and ease of disposal, and are therefore recyclable.

Returning the packaging into the material cycle con-

serves raw materials and reduces the amount of waste

generated. Dispose of packaging materials that are no

longer needed in accordance with applicable local

regulations.

GB

│

CY

│

9 ■

SLS 2200 C2

Attaching the suction cups

NOTE

► To make sure that the suction cups

hold ﬁrmly, the surface

must be completely free of dust, oil and grease.

Variant A

Variant A is suitable for attaching the device to a ﬂat, level surface.

♦ Attach all four suction cups

to the underside of the device,

as shown in “Figure A”.

♦ Push the suction cups

into the large holes.

♦ Now fasten the suction cups

by sliding them into the narrow

openings.

Figure A

♦ You can now attach the device on a ﬂat, level using the suction

cups .

■ 10

│

GB

│

CY

SLS 2200 C2

Variant B

Variant B is suitable for attaching the device to a pane of glass.

♦ Attach the four suction cups

to the two brackets

,

as

shown in “Figure B”.

♦ Push the suction cups

into the large holes.

♦ Now fasten the suction cups

by sliding them into the narrow

openings.

♦ Now mount the brackets

on the underside of the device by

pushing the retaining lugs into the corresponding slots on the

rear of the device and locking them in place.

Figure B

♦ You can now attach the device to a pane of glass using the

suction cups .

GB

│

CY

│

11 ■

SLS 2200 C2

Charging with the solar panel

CAUTION

► Ensure that the ambient temperature does not exceed 45°C.

This is particularly important when using the device inside a

motor vehicle.

You can charge the battery of the device with the solar panel

.

Ensure that the solar panel

is receiving suﬃcient sunlight.

As soon as there is suﬃcient sunlight, the solar LED

lights up

orange to show that the battery is being charged. If the solar

LED

does not light up, there is not enough sunlight available.

In this case, change the location of the device or place the device

in direct sunlight. Once the solar LED

lights up green, the battery

is fully charged.

■ 12

│

GB

│

CY

SLS 2200 C2

Charging with the USB cable

If there is no sunlight available, you can charge the battery of the

device with the USB cable

. To do this, connect the micro-USB

plug of the charging cable to the device’s micro-USB port

.

Connect the USB plug of the USB cable to a USB port on your

computer. The charging progress will be indicated by means of

the charge level LEDs

.

Charge level LEDs

Charge level

One LED is ﬂashing < 25%

One LED is on, the second LED is ﬂashing 25–49%

Two LEDs are on, the third LED is ﬂashing 50–74%

Three LEDs are on, the fourth LED is ﬂashing 75–99%

All LEDs are on 100%

NOTE

► Some computers deactivate the power supply to the USB

ports when they are switched oﬀ. If the solar charger’s

battery is not being charged, check to see whether your

computer is turned on.

► Alternatively, you can charge the battery of the solar charger

with an external USB power supply (not supplied).

To do this, use the USB cable

supplied with the product.

You can purchase a suitable 5 V USB power adapter with

an output of at least 500mA from most electronics stores.

GB

│

CY

│

13 ■

SLS 2200 C2

Handling and operation

Switch the device on/oﬀ

Switching on

♦ Press the ON/OFF button

brieﬂy to switch on the device.

The charge level LEDs

light up for about 10 seconds.

The

LED lights up blue as long as a connected device

is being charged.

Automatic switch-oﬀ

♦ If no device is connected for charging within 10 seconds, the

charger switches oﬀ automatically to conserve its battery.

Switching oﬀ

♦ Press and hold the ON/OFF button

for at least 3 seconds

to switch oﬀ the device and stop the charging process.

The

LED goes out.

Display charge level

♦ Press the ON/OFF button brieﬂy to show the charge level

of the battery for a few seconds. The charge level LEDs

show you the charge level.

Charge level LEDs

Charge level

All LEDs are on 100%

Three LEDs are on 75–99%

Two LEDs are on 50–74%

One LED is on 25–49%

One LED is ﬂashing < 25%

All LEDs oﬀ 0%

■ 14

│

GB

│

CY

SLS 2200 C2

Compatible devices

You can use the solar charger to charge end devices that require

a charging current of at least 60 mA and a maximum of 1A.

If the connected end device requires a current of less than 60 mA

or more than 1A, the solar charger will switch itself oﬀ immedi-

ately after being switched on with the ON/OFF button

. In this

case, check the charger’s suitability for your end device on the

basis of the technical data of your end device.

Charging external devices

Connect the charging cable of your end device to the USB port

on the solar charger and to your end device.

♦ If charging does not start automatically, press the ON/OFF

button

brieﬂy to start the charging process.

The

LED lights up for as long as the connected device

is being charged. Once your device is fully charged, the solar

charger switches oﬀ. To interrupt the charging process, you can

disconnect the end device. If your end device is not fully charged

and the

LED goes out during charging, this means the solar

charger’s battery is discharged. The solar charger’s battery must

be recharged again before you can charge end devices.

Simultaneous charging of the built-in battery and a connected

device is only possible in solar operation. Simultaneous charging

of the built-in battery via the micro-USB port

and a connected

device is not possible.

GB

│

CY

│

15 ■

SLS 2200 C2

Troubleshooting

A connected device is not charging.

♦ Press the ON/OFF button

brieﬂy to start the charging process.

♦ The solar charger’s battery is empty. Charge the battery.

♦ No connection to the device. Check the connection.

♦ The solar charger can be used for end devices that require a

charging current of no more than 1A. If the connected end

device requires a current of more than 1A, the solar charger

will switch itself oﬀ immediately after being switched on with

the ON/OFF button

. In this case, check the charger’s suit-

ability for your end device on the basis of the technical data

of your end device.

The solar charger’s battery is not charging via the solar

panel.

♦ Check that the solar panel

is receiving suﬃcient sunlight.

The solar charger’s battery is not charging via the USB

cable.

♦ Connection is faulty. Check the connection.

♦ Some computers deactivate the power supply to the USB ports

when they are switched oﬀ. If the solar charger’s battery is not

being charged, check to see whether your computer is turned on.

NOTE

► If the above-mentioned solutions do not resolve the problem,

please contact Customer Service (see chapter Service).

■ 16

│

GB

│

CY

SLS 2200 C2

Cleaning

CAUTION

Damage to the device!

► To avoid irreparable damage to the device, ensure that no

moisture can penetrate the device during cleaning.

► Do not use caustic, abrasive or solvent-based cleaning

materials. These can damage the surfaces of the device.

♦ Clean the surfaces of the device with a soft, dry cloth. For stub-

born dirt, use a slightly damp cloth with a mild detergent.

Storage when not in use

♦ If you do not intend to use the device for a long time, store it in

a clean, dry place away from direct sunlight.

♦ If the solar charger is not going to be used for some time, the

battery should be recharged at regular intervals. This helps to

preserve battery performance.

GB

│

CY

│

17 ■

SLS 2200 C2

Disposal

The adjacent symbol of a crossed-out wheelie bin

means that this device is subject to Directive

2012/19/EU. This directive states that this device

may not be disposed of in the normal household

waste at the end of its useful life, but must be handed over to

specially set-up collection locations, recycling depots or disposal

companies.

This disposal is free of charge for the user. Protect

the environment and dispose of this device properly.

You can obtain further information from your local disposal com-

pany or the city or local authority.

Pagina se încarcă ...

Silvercrest SLS 2200 C2 Operating Instructions Manual

Silvercrest SLS 2200 C2 Operating Instructions Manual

în alte limbi

Lucrări conexe

Alte documente