Silvercrest SWEP 500 A1 Operating Instructions Manual

KOMPERNASS GMBH

BURGSTRASSE 21 · D-44867 BOCHUM

www.kompernass.com

ID-Nr.: SWEP500A1-11/11-V4

IAN: 71305

Multi-Band Radio SWEP 500 A1

Weltempfänger

Bedienungsanleitung

Radio prijemnik

Upute za upotrebu

Multi-Band Radio

Operating instructions

Δέκτης παγκοσμίου

λήψεως

Οδηγίες χρήσης

Radio

Instrucţiunile

Радиоприемник

Ръководство за експлоатация

R

CV_71305_SWEP500A1_LB7.qxd 20.12.2011 10:45 Uhr Seite 1

1

B

A

SWEP 500 A1

2

3

4

5

6

7

8

90q

we

r

t z

iu

o p

CV_71305_SWEP500A1_LB7.qxd 20.12.2011 10:45 Uhr Seite 4

- 1 -

CONTENTS PAGE

Intended use 2

Technical Data 2

Symbols used 4

Safety information 5

Operating elements 9

Starting up 10

General functions 12

Time functions 12

Time, date, time zone and world time . . . . . . . . . . . . . . . . . . . . .13

Select display mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Alarm function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Stop watch function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Countdown function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Radio operation 24

Setting the station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Fine tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Memory functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Cleaning 29

Disposal 29

Importer 30

Warranty & Service 30

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 1

MULTI-BAND RADIO

Before using the device for the first time, read these operating instructions

carefully and keep them for later reference. Hand the instructions over

when transferring the device to a third party.

This documentation is copyright protected. Every duplication resp. every

copying, also as extracts, as well as any reproduction of images, even in an

altered state, is only permitted with the written consent of the manufacturer.

Intended use

This appliance is intended for receiving generally approved radio transmis-

sions in all countries (world receiver) and only for domestic use.

Utilisation other than as described here is not permitted and it could lead

to damages and injuries. No liability will be accepted for damages resulting

from misuse or improper handling, the application of force or unauthorised

modifications.

Technical Data

This appliance fulfills, in regard to conformity with, the fundamental require-

ments and other relevant provisions of the EMC Directive 2004/108/EC,

the Low Voltage Directive 2006/95/EC and the Ecodesign Directive

2009/125/EC (Commission Regulation 1275/2008 Annex II, No .1).

- 2 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 2

Power consumption: 5 watts

Power consumption Standby: approx. 1 W

Operating temperature: +5

~

+40°C

Humidity: 5

~

90% (no condensation)

Dimensions (W x H x D): 17.7 x 11 x 3.9 cm

Appliance weight: approx. 425 g

Power transformer weight: approx. 185 g

Batteries

4x 1.5 V, Type AA/LR6/Mignon (not supplied)

Frequency range radio:

VHF (FM): 87 – 109 MHz

SW: 5.85 – 17.90 MHz

MW (AM) Europe 522 – 1656 kHz

MW (AM) USA 520 – 1710 kHz

LW 144 – 299 kHz

The technical features of the device enable the frequency ranges stated

above to be set. Various countries may have different national rules on the

radio frequency ranges assigned. Please note that you may not sell, transfer

to third parties or abuse information received outside the assigned radio

frequency ranges.

Tuning ranges (NORMAL/FINE):

FM (VHF) 100 kHz /50 kHz

SW 5 kHz /1 kHz

MW (AM) Europe 9 kHz /1 kHz

MW (AM) USA 10 kHz /1 kHz

LW 1 kHz

Sensitivity: SW can be set to 2 intervals

- 3 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 3

General

Memory positions: 400

Headphones

Model: E105

Impedance: 32 Ω

Wideband characteristic

Voltage (WBCV): approx. 110 mV

Headphone socket

max. Output voltage: approx. 35 mV

Power transformer

Manufacturer: Everway Industries Ltd.

Model: EW35V400-090A

Primary: 230 V

~

50 Hz / 25 mA

Secondary: 9 V

~

400 mA / 3,6 VA

Symbols used

These symbols bring to your attention that here a warning notice

follows in regard to one of the following matters:

- Risk of injury,

- Risk of electric shocks,

- Risk of fire,

- Risk of explosion,

plus bringing your attention to important matters such as:

- Information regarding the handling of batteries,

- Information about voltage surges,

- Information about mains-power disconnection.

- 4 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 4

This symbol warns about submersing the appliance in water or

other liquids.

This symbol warns you about hearing damage.

Note:

With this symbol you are given tips about interaction with the appliance.

Safety information

• This device has not been designed for use by people (including children)

with restricted physical, sensory or intellectual abilities or lack of expe-

rience and/or knowledge, unless they are supervised by a responsible

person (for their own safety) or have received instructions on how to

use the device.

• Children should be supervised to ensure that they do not play with

the device.

• In order to avoid the device being switched on unintentionally, remove

the adapter from the mains socket after each use and before cleaning.

• Check the device and all parts for visible damage. The device’s safety

concept can only work if the device is in perfect condition.

• A mains adapter connected to the device must always be easily

accessible so that the device can be quickly disconnected from the

mains power in an emergency.

- 5 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 5

Risk of electric shock!

• Connect the mains-power adapter only to correctly installed and

earthed mains sockets. Ensure that the rating of the local power

supply tallies completely with the details given on the rating plate of

the appliance.

• Damaged adapters or mains cables should be exchanged immediately

by an authorised technician or the Customer Service in order to

avoid risks.

• Connection cables or devices that do not work perfectly or have been

damaged should be repaired or exchanged immediately by Customer

Services.

Never immerse the device in water! Simply wipe it with a slightly

damp cloth.

• Do not expose the wall wart to rain or use it in a damp or wet

environment.

• Ensure that the connection cable is never wet or damp when in use.

• You must not open or repair the device’s housing. This can be dangerous

and renders the warranty null and void.

• Protect the device from moisture and sprayed water. Therefore do not

place any objects filled with water (e.g. vases) on or near the device.

Risk of fire!

• Do not use the device near hot surfaces.

• Do not set the device up where it is exposed to direct sunlight.

This could cause it to overheat and damage it beyond repair.

• Never leave the device unattended during operation.

• Never cover the device’s ventilation slots when it is switched on.

• Do not place open flames, such as candles, on or near the device.

- 6 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 6

Risk of injury

• Keep children away from the connection cable and device.

Children frequently underestimate the danger of electrical devices.

• If the device has fallen down or is damaged it must no longer be used.

Have the device checked by a qualified specialist and, if necessary,

repaired.

• Batteries must not be handled by children.

Children can put batteries in their mouths and swallow them.

If a battery has been swallowed, obtain medical assistance immediately.

Thunder storms!

Devices connected to mains power can be damaged during a thunder

storm. If there is a thunder storm, always remove the mains plug from

the socket.

Information on voltage surges (EFT/electrical fast

transient) and electrostatic discharges:

If the product does not work properly due to electrical fast transient

processes (voltage surges) or electrostatic discharge, it must be

reset to restore normal operation. If necessary, remove the plug from

the power socket and insert it again. The batteries (if used) must be

removed and reinserted.

Information on separating the device from

mains power

The POWER button on this device does not completely separate it from

the mains network. In addition, the device uses power when in standby

mode. In order to completely separate the device from the mains supply

the plug must be removed from the mains socket.

- 7 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 7

Notes on handling batteries

The device uses batteries. Please note the following on handling batteries:

Risk of explosion!

Do not throw batteries into a fire. Do not recharge batteries.

• Never open, solder or weld batteries. There is a risk of explosion and injury!

• Check batteries regularly. Leaking batteries can damage the device.

• If the appliance is not going to be used for long periods, remove the

batteries.

• If batteries leak, put on protective gloves.

• Clean the battery compartment and contacts with a dry cloth.

Caution!

No liability/warranty applies to damage to the device caused by

moisture due to water penetrating the device or overheating!

- 8 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 8

Operating elements

A Front panel

q

Save buttons M.0/5 - M.4/9

w

Display

e

Button SNOOZE/SLEEP TIMER

r

Waveband selector switch (LW/SW/MW/FM)

t

BASS button

y

FINE button

u

UP/DOWN buttons

i

VOL+(AL-1)/VOL-(AL-2) buttons

o

MODE button

a

POWER button

s

MEM button

d

PAGE button

f

MEMORY SCAN button

g

Loudspeakers

B Back

h

Stand

j

Aerial

k

Carrying strap

l

switch SW SEN. (DX/LX)

;

Headphone output

2)

AC

~

9V 400 mA: Mains adapter connection

- 9 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 9

Starting up

Unpack the device

Remove all packaging materials.

Caution!

Do not let children play with the plastic film. There is a risk of suffocation.

Check the items supplied

Whilst unpacking, check that all of the following items are available to you:

• Shortwave Radio

• Power transformer

• Headphones

• Storage case

• These operating instructions

Mains and battery operation

When you disconnect the radio from the mains supply, any settings you

may have made (time, alarm, stations in memory) will be lost. If you wish

to keep these settings, insert batteries (see below) before disconnecting.

Inserting batteries

The device can also be operated with batteries (not supplied) as well as

from the mains. You will need four 1.5V mignon batteries, size AA/LR6.

• Open the battery compartment on the rear of the device by sliding

the cover downwards.

• Insert four batteries into the compartment, paying attention to

the polarity.

- 10 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 10

• Replace the cover on the battery compartment.

If the batteries become too weak, this is indicated by the symbol

blinking in the display. Subsequently, the appliance then switches itself off.

Mains connection

• Connect the plug of the mains adapter to the AC

~

9V 400 mA socket on

the side of the device.

• Plug the mains adapter into an easily accessible socket. To avoid

tripping hazards, please avoid using an extension cable.

Note:

When the power adapter is connected the device is supplied with electricity

only through the power adapter, not from the batteries. The installed batte-

ries are not charged. In the event of prolonged use of the power adapter the

batteries should be removed from the battery compartment. Otherwise there

is a risk that the batteries may leak.

Connecting headphones

On the left side of the radio, you will find the headphone socket.

Caution!

With this appliance, use only the supplied type E105 headphones.

• Insert the headphone jack plug into the headphone output.

The speaker will be deactivated automatically.

Caution:

Listening to music with headphones for long periods and at high

volume levels can lead to hearing damage!

- 11 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 11

General functions

Key lock

In order to prevent changing the settings unintentionally by touching the

buttons, you can activate the key lock.

• With the radio switched on, press and hold the button

MEM for about

3 seconds. On screen, the message flashes. All buttons, except

the buttons

SNOOZE and MEM, are now blocked.

• Press and hold down the

MEM button again for about 3 seconds to

cancel the key lock. The message on the screen disappears.

Screen lighting

• Press any button to illuminate the screen. The screen will remain lit for

about 15 seconds.

Stand

• Fold out the base on the rear of the device to make the device

more stable.

Time functions

When the power provision is established (mains or battery operation) the

time indicated by the world receiver begins at “0:00 00” Proceed with set-

tings the date and time, as explained in the following sections.

The time functions can only be programmed when the radio is switched off.

If the device is disconnected from mains power or the batteries are remo-

ved, the settings are lost.

- 12 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 12

Time, date, time zone and world time

You can set the time, date and time zone via the MODE button. You can con-

tinue to query and adjust the universal time, the date alarm, the medium-

wave reception, alarm time interruption and the hours mode.

When you press the button

MODE with the radio switched off, the function to be

programmed blinks for about 15 seconds. During this time, adjust the setting

with the

UP/DOWN buttons.

• Press

MODE x 1: Setting clock time

• Press

MODE x 2: Setting the date

• Press

MODE x 3: Set time zone (“Local City”)

• Press

MODE x 4: Show world time

• Press

MODE x 5: Date alarm

• Press

MODE x 6: Set reception range for medium wave.

• Press

MODE x 7: Set alarm pause.

• Press

MODE x 8: Set 12/24 hour mode.

To apply a setting, just wait until the screen stops flashing (the screen reverts

to the time indication) or press MODE to move on to the next function.

- 13 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 13

Setting clock time

• Press MODE once. The most recently set time flashes on the screen.

• Press the

UP or DOWN button to move the time forward or backward at

minute intervals. Hold down one of the buttons for a few seconds to

move the setting forward or backward quickly at 10 minute intervals.

Setting the date

• Press MODE again or twice.

The date set flashes on the screen (“Su 1.01.12” when first switched on).

• Press the

UP or DOWN button to move the date forward or backward.

Keep either of these buttons pressed for a few seconds to change the

date in ten-day steps.

The weekday indication follows automatically. The indication uses the first

two letters of the English name of the day.

The built-in calendar runs from 2000 to 2099.

Day of the week indication:

Su = Sunday

Mo = Monday

Tu = Tuesday

We = Wednesday

Th = Thursday

Fr = Friday

Sa = Saturday

- 14 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 14

Setting the time zone

• Press MODE again or three times. The selected time zone flashes on the

screen as the abbreviation for the corresponding city (UTC when first

switched on); the time disappears.

• Press the

UP or DOWN button to move the time zone forward or backward.

The following table summarises the city abbreviations for the time zones and

time differences.

- 15 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 15

Short code Difference from CET

Summer time

Town

HNL -10:00

no

Honolulu/USA

ANC -9:00

yes

Anchorage/USA

YVR -8:00

yes

Vancouver/Canada

LAX -8:00

yes

Los Angeles/USA

DEN -7:00

yes

Denver/USA

CHI -6:00

yes

Chicago/USA

MEX -6:00

yes

Mexico City/Mexico

NYC -5:00

yes

New York/USA

YYZ -5:00

yes

Toronto/Canada

YUL -5:00

yes

Montreal/Canada

CCS -4:30

no

Caracas/Venezuela

RIO -3:00

yes

Rio de Janeiro/Brazil

BUE -3:00

no

Buenos Aires/Argentina

UTC* 0:00

no

Universal Time Coordinated

LON 0:00

yes

London/GB

BER 1:00

yes

Berlin/Germany

PAR 1:00

yes

Paris/France

ROM 1:00

yes

Rome/Italy

CAI 2:00

yes

Cairo/Egypt

IST 2:00

yes

Istanbul/Turkey

MOW 3:00

yes

Moscow/Russia

KWI 3:00

no

Kuwait City/Kuwait

DXB 4:00

no

Dubai/United Arab Emirates

KHI 5:00

no

Karachi/Pakistan

DAC 6:00

yes

Dhaka/Bangladesh

BKK 7:00

no

Bangkok/Thailand

SIN 8:00

no

Singapore

HKG 8:00

no

Hong Kong

PEK 8:00

no

Beijing/China

SHA 8:00

no

Shanghai/China

TYO 9:00

no

Tokyo/Japan

SYD 10:00

yes

Sydney/Australia

NOU 11:00

no

Noumea/New Caledonia

AKL 12:00

yes

Auckland/New Zealand

- 16 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 16

*UTC

Universal Time Coordinated (UTC). UTC is the reference for the times of the

various time zones around the world.

Show world time

• Press MODE again or four times to show the world time. The city

abbreviation appears with the corresponding time.

• Press the

UP or DOWN button to move the time zone forward or backward.

Note:

To correctly present your set world time, you must set the summer time offset

depending on the world time (see table).

Summer Time Offset

Not every time zone around the world differentiates between summer time

and winter time. To correctly display your world time, you must set the sum-

mer time offset dependant on the time zone.

• When the display for the time zone is flashing, repeatedly press the

SNOOZE button until the corresponding time offset is set (see table).

Time offset Display Explanation

1 OFFSET 1

In your time zone (Local City) it is winter time and

in the set world time it is summer time.

0 OFFSET 0

In your time zone (Local City) and in the set world

time it is summer resp. winter time.

-1 OFFSET -1

In your time zone (Local City) it is summer time and

in the set world time it is winter time resp. they do

not have summer time.

- 17 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 17

Special date alarm

• Press the MODE button a fifth time to set the special date alarm.

The screen flashes SDA1 and the date in succession.

• Press the

PAGE button to select one of the ten settable date alarms

(SDA1–SDA 10).

• Press the

UP or DOWN button to set the date on which the alarm should

sound.

• Press the

SNOOZE button to ignore the year number setting so that the

alarm sounds every year.

• When the current date tallies with the SDA alarm, on that day an

alarm sounds for 10 minutes on every hour from 8:00 - 23:00.

In addition, the SDA message will flash on the screen.

• Turn off the alarm by pressing any button.

Note:

In order to completely deactivate the date alarm set a date that is in the past!

Setting 12/24 hour mode

• Press MODE eight times. The screen shows the”24 HR” message for

24-hour mode.

• Press the

UP button to set the 24 hour mode.

• Press the

DOWN button to set the 12 hour mode.

“12 HR” is displayed on the screen. In the afternoon in addition PM is

shown on the screen.

- 18 -

IB_71305_SWEP500A1_LB7 20.12.2011 9:51 Uhr Seite 18

Pagina se încarcă ...

Silvercrest SWEP 500 A1 Operating Instructions Manual

Silvercrest SWEP 500 A1 Operating Instructions Manual

Lucrări conexe

Alte documente