Silvercrest SKRD 30 A1 Operating Instructions Manual

Categorie
Ceasuri cu alarmă
Tip
Operating Instructions Manual
Under-Cabinet Radio SKRD 30 A1
R
Кухненско радио
Ръководство за експлоатация
Radio
Instrucţiuni de utilizare
R
Under-Cabinet Radio
Operating instructions
Ugradbeni radio
Upute za upotrebu
Unterbau-Radio
Bedienungsanleitung
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID-Nr.: SKRD 30 A1-07/11-V3
IAN: 69030
CV_69030_SKRD30A1_LB7.indd 1-3CV_69030_SKRD30A1_LB7.indd 1-3 17.08.2011 15:35:03 Uhr17.08.2011 15:35:03 Uhr
SKRD 30 A1
A
B
1
2
3
zt
4
uiopp
5 6 7 8 9 0 q w e r
CV_69030_SKRD30A1_LB7.indd 4-6CV_69030_SKRD30A1_LB7.indd 4-6 17.08.2011 15:35:09 Uhr17.08.2011 15:35:09 Uhr
1
SKRD 30 A1
GB
Index
Introduction . . . . . . . . . . . . . . 2
Information for these operating
instructions . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . .2
Proper usage . . . . . . . . . . . . . . . . . . 2
Warning notices . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . 4
Danger from electric shock . . . . . . . . 4
Handling of batteries . . . . . . . . . . . . 4
Basic Safety Instructions . . . . . . . . . . 5
Operating components . . . . . 6
Setting up and connecting . . .7
Safety instructions . . . . . . . . . . . . . . 7
Package contents and transport
inspection . . . . . . . . . . . . . . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . 7
Disposal of the packaging . . . . . . . . 8
Set-up location requirements. . . . . . .8
Electrical connection . . . . . . . . . . . . . 8
Inserting the battery . . . . . . . . . . . . . 9
Mounting under a wall cupboard . . 9
Disassembly . . . . . . . . . . . . . . . . . .10
Setting up the device . . . . . . . . . . .10
Providing mains power . . . . . . . . . .10
VHF wire antenna . . . . . . . . . . . . .10
Handling and operation . . .11
Switching On and Off . . . . . . . . . .11
Basic settings . . . . . . . . . . . . . . . . .11
Activating the settings menu . . . . .11
Setting the time . . . . . . . . . . . . . . . .12
Setting the date . . . . . . . . . . . . . . .12
Setting the memory function . . . . . .12
Setting the time of day format . . . .13
Setting automatic display dimming. 13
Setting the display dimming’s
switch on and off time . . . . . . . . . .14
Kitchen timer . . . . . . . . . . . . . . . . . .14
Setting the kitchen timer . . . . . . . . .14
Starting the kitchen timer . . . . . . . .15
Pausing the kitchen timer. . . . . . . . .15
Programming the kitchen timer . . . .16
Accessing the kitchen timer . . . . . .16
Programming alarm wake times . . .17
Wake with alarm tone . . . . . . . . . .17
Waken with radio . . . . . . . . . . . . . .18
Switching the alarm off . . . . . . . . . .18
When the wake time has arrived . .18
The Reminder function . . . . . . . . . .19
Radio operation . . . . . . . . . . . . . . .19
Switching the radio on/off . . . . . . .19
Adjusting the volume. . . . . . . . . . . .19
Manual station selection. . . . . . . . .19
Search for the next station . . . . . . .20
Saving stations manually . . . . . . . .20
Access saved stations . . . . . . . . . .20
Automatic station search
(AMS function) . . . . . . . . . . . . . . .20
Additional functions . . . . . . . . . . . .21
Automatic switch off (Sleep function) .21
Button lock . . . . . . . . . . . . . . . . . . .21
Bass accentuation . . . . . . . . . . . . . .21
Setting the display brightness
manually . . . . . . . . . . . . . . . . . . . . .22
Setting alternative display . . . . . . .22
Cleaning . . . . . . . . . . . . . . . .22
Safety instructions . . . . . . . . . . . . .22
Cleaning the housing . . . . . . . . . . .22
Troubleshooting . . . . . . . . . .23
Safety instructions . . . . . . . . . . . . .23
Malfunction causes and remedies .23
Storage/Disposal . . . . . . . . .24
Storage . . . . . . . . . . . . . . . . . . . . . .24
Disposal of the device . . . . . . . . . .24
Disposing of the batteries . . . . . . . .24
Appendix . . . . . . . . . . . . . . .25
Information regarding the
EG conformity declaration . . . . . . .25
Technical data . . . . . . . . . . . . . . . .25
Warranty . . . . . . . . . . . . . . . . . . . .26
Service . . . . . . . . . . . . . . . . . . . . . .26
Importer . . . . . . . . . . . . . . . . . . . . .26
2
Introduction
SKRD 30 A1
GB
Introduction
Information for these operating instructions
These operating instructions are a component of the Under-Cabinet Radio
SKRD 30 A1 (henceforth designated as the device) and they provide you with
important information about the intended use, safety, installation and connection
as well as operation of the device.
The operating instructions must be kept available in the vicinity of the device
at all times. They are to be read and used by anyone assigned to service and
repair faults in the device.
Retain these operating instructions and pass them on with the device to any
future owners.
Copyright
This documentation is copyright protected.
Any copying or reproduction, including as extracts, as well as the reproduction
of images, also in an altered state, is not permitted without the express written
consent of the manufacturer.
Proper usage
This device is only intended for the reception of VHF radio programmes, as a
kitchen timer and as an alarm by means of an alarm tone or radio in enclosed
spaces. The device is intended as a free standing unit or for mounting under a
cupboard. For these purposes the supplied stand and/or mounting plate must be
used. Any other use or uses beyond those mentioned are considered unintended
use. The device is not intended for use in commercial or industrial environments.
WARNING
Danger from unintended use!
Danger from the device can result if it is used for unintended purposes and/or
other types of use.
Use the device exclusively for intended purposes.
Observe the procedures described in these operating instructions.
No warranty claims of any kind will be accepted for damage caused by improper
use, unauthorised r
epair
s, unauthorised modifi cations or for the use of unapproved
replacement parts.
The operator alone bears liability.
3
Introduction
SKRD 30 A1
GB
Warning notices
In the current operating instructions the following warning notices are used:
DANGER
A warning in this danger level indicates a hazard threatening
situation.
In the ev
ent that the hazardous situation is not avoided it can lead to death
or serious injury.
The directives in this warning are there in order to avoid the danger of
death or serious injury.
WARNING
A warning of this danger level signifi es a possible dangerous
situation.
If the dangerous situation is not avoided it can lead to injuries.
The directives in this warning are there to avoid personal injuries.
IMPORTANT
A warning of this danger level signifi es possible pr
operty
damage.
If the situation is not avoided it can lead to property damage.
The directives in this warning are there to avoid property damage.
NOTICE
A notice signifi es additional information that assists in the handling of the
device.
4
Introduction
SKRD 30 A1
GB
Safety
In this section you receive important safety information regarding handling of the
device.
This device complies with the statutory safety regulations. Incorrect usage can
lead to injuries and property damage.
Danger from electric shock
DANGER
Risk of fatal electrocution!
A life-t
hreatening situation can arise from contact with live
wires or components!
Observe the following safety instructions to avoid electric shock hazards:
Do not use the device if the mains power plug or the connection cable are
damaged.
Do not, under any cir
cumstances, open the device housing. The risk of an
electric shock is present if the power carrying connections are touched or
the electrical or mechanical construction is changed.
Handling of batteries
WARNING
Danger from improper use!
For safe handling of batteries observe the following safety instructions:
Do not throw batteries into a fi re. There is the risk of an explosion!
Do not short circuit batteries.
Do not attempt to recharge batteries.
Regularly check the condition of the batteries. Leaking battery acid can
cause permanent damage to the device. Special caution should be shown
when handling damaged or leaking batteries. Danger from acid burns!
Wear protective gloves.
Store batteries in a place inaccessible to children. If swallowed seek
immediate medical attention.
If you do not intend to use the de
vice for an extended period of time,
remove the batteries.
5
Introduction
SKRD 30 A1
GB
Basic Safety Instructions
For safe handling of the device observe the following safety instructions:
Before use check the device for visible external damage. Do not put into
operation a device that is damaged or has been dr
opped.
Damaged cables or connections should be replaced by authorised qualifi ed
persons or by the customer service department.
This device is not intended for use b
y individuals (including children) with
restricted physical, physiological or intellectual abilities or defi ciences in
experience and/or kno
wledge unless they are supervised by a person
responsible for their safety or receive from this person instruction on how
the device is to be used.
Children must be supervised in order to make sure that they do not play with
the device.
Repair
s should only be carried out by authorized specialist companies or by
the customer service department. Incorrect repairs can result in danger to the
user. In addition w
arranty claims become void.
A repair to the device during the warranty period may only be carried out
by a customer service department authorized by the manufacturer otherwise
no additional warr
anty claims can be considered for subsequent damages.
Defective components may only be replaced with original replacement parts.
Only by using original replacement parts can you guarantee that the safety
requir
ements are complied with.
Protect the device from moisture and liquid penetration. Never submerge the
device in water, do not place the device in the vicinity of water and do not
stand any object fi
lled with liquid (i.e. vases) on the device.
Do not place any objects on the device.
Do not operate the device in the vicinity of open fl ames (i.e. candles).
Avoid direct sunlight.
Always pull on the power plug when disconnecting from the wall socket,
never pull on the connection cable.
If malfunctions occur or thunder storms thr
eaten pull the po
wer plug from the
wall socket.
6
Operating components
SKRD 30 A1
GB
Operating components
(for illustrations see fold out sides fi gure A)
Mounting plate/Stand
2
Control panel
3
Display
4
On/Off : On/Off switch (Radio)
5
Dimmer/AOT: Display brightness setting/Switch off timer
6
Lock/Mem.: Button lock/memory slot selection
7
Bass/AMS/Mode: Bass accentuation/Station search/Access setting menu
8
Alarm 1: Alarm 1 programming/Alternative display settings
9
Alarm 2: Alarm 2 programming/Alternative display settings
10
Preset–: selection of the previous memory slot
11
Preset+: selection of the next memory slot
12
Tune–: Decrease the reception frequency
13
Tune+: Increase the reception frequency
14
VOLUME/Snooze/Timer: Volume control/Alarm switch off /Timer setting
15
Wire antenna for VHF reception
16
Mains connection cable
17
Recesses for stand
18
Speakers
19
Battery compartment
20
Unlocking buttons for the mounting plate
7
Setting up and connecting
SKRD 30 A1
GB
Setting up and connecting
Safety instructions
WARNING
Damage may occur to property and injuries to people when
operating the device!
Observe the following safety instructions to avoid dangers:
Packaging material should not be used as a play thing. There is a risk of
suff ocation!
To av
oid risks to persons and property, observe the requirements for the
set-up location and the electrical connections.
Package contents and transport inspection
The device is delivered with the following components as standard:
Under-Cabinet Radio SKRD 30 A1
Mounting plate/Stand
4 Securing screws
1 x Battery 3 V Type CR2032
Operating instructions
NOTICE
Check the contents to make sure everything is there and for visible damage.
If the items supplied are incomplete, or damaged due to defective packaging
or transportation, contact the Service Hotline (see section Service
).
Unpacking
Remove all device parts and the operating instructions from the carton.
Remove all packing material.
8
Setting up and connecting
SKRD 30 A1
GB
Disposal of the packaging
The packaging protects the device from transport damage. The packaging ma-
terials are selected from the point of view of their environmental friendliness and
disposal technology and are therefore recyclable.
The recirculation of packaging into the material circuit saves on raw material
and reduces generated waste. Dispose of packaging material that is no longer
needed according to the regionally established regulations.
NOTICE
If possible preserve the device's original packaging during the warranty
period so that in the case of a warranty claim you can package the device
properly for r
eturn.
Set-up location requirements
For the safe and fault free operation of the device, the set-up location must fulfi ll
the following conditions:
When setting up the device place it on a fi rm, fl at and even surface. Use the
supplied stand.
Set up or mount the device in such a w
ay that the available ventilation open-
ings and the speaker ar
e not covered.
Do not operate the device in a hot, wet or very humid location or in the vicin-
ity of fl ammable materials.
The surfaces of furnitur
e may contain components that could aff ect and sof-
ten the rubber feet on the device. If necessary, place an anti-slip mat under
the rubber feet of the device.
The w
all socket must be easily accessible so that, in an emergency, the plug
can be quickly withdrawn from the socket.
Electrical connection
Before connecting the device, compare the connection data (voltage and
frequency) on the rating plate of the device with that of your power supply
network. This data must be compatible to avoid possible damage to the device.
Make sure that the device’s connection cable is not damaged and is not
laying over hot surfaces and/or sharp edges.
Make sur
e that the connection cable is not tightly stretched or bent.
Do not allow the connection cord to hang over edges (Trip wire eff ect).
9
Setting up and connecting
SKRD 30 A1
GB
Inserting the battery
By inserting the battery you can avoid the loss of programmed time of day and
alarm times in the event of a possible power outage. The battery ensures that
the internal clock continues to run even during a power failure. When power is
restored the correct time appears automatically in the display
3
.
NOTICE
The device can also be operated without a battery.
Open the cover of the battery compartment
19
on the underside of the
device by turning the cover to the left, with a coin, as far as it will go and
then lift off .
Insert the battery type CR2032 (supplied) into the battery compartment.
The side with the marking + points upwards.
Close the battery compar
tment by attaching the cover and then with a coin
turn it to the right.
Mounting under a wall cupboard
(Illustration see fold out side fi gure B)
With the supplied mounting plate you can mount the device under, for exam-
ple, a wall cupboard. For mounting of the device proceed as follows:
Press both unlocking buttons
20
on the rear panel of the device downwards
thereby, at the same time, sliding the mounting plate backwards and
remove the mounting plate .
Find a suitable set-up location for the device (see also the section
Requirements for the set-up location).
Hold the mounting plate
under the set-up location. Thereby the front edge
of the mounting plate should be approx. 3,5 cm behind the front of the
cupboard so that, after Remove the mounting, the device is fl ush with the
cupboard.
Mark the 4 fastening points with a pencil.
Using a spike or nail, make a small depression at the respective marking
points. Screw the mounting plate
tightly with the supplied screws as
illustrated in fi gure B.
Place the device aslant, with the front recesses in the top face, in the mount-
ing plate
. Press the rear part of the device upwards against the mounting
plate until the device audibly locks into place.
Check to make sure that the device is secure.
10
Setting up and connecting
SKRD 30 A1
GB
Disassembly
Press both unlocking buttons
20
on the rear panel of the device downwards,
thereby sliding, at the same time, the device forward and then remove the
device downwards.
Unscrew the screws on the mounting plate
and remove the mounting
plate .
Setting up the device
As an alternative you can stand the device on a top. So as not to cover up the
ventilation slots and the speaker
18
on the underside of the device, when setting
up the device it must be mounted on the stand . For assembly of the stand
proceed as follows:
Press both unlocking buttons
20
on the rear panel of the device downwards
thereby, at the same time, sliding the mounting plate backwards and remove
the mounting plate . The mounting plate can now be used as a stand.
Slide both front retaining tabs of the stand
into the rear recesses
17
on
the underside of the device.
Press both rear retaining tabs of the stand
into the front recesses
17
on
the underside of the device until the stand audibly locks into place.
Find a suitable set-up location for the device (see also the section
Requirements for the set-up location).
Providing mains power
Insert the mains connection cable
16
power plug into a socket. The time of
day will be shown in the display
3
( o’clock).
VHF wire antenna
Unwind the wire antenna
15
completely for VHF reception.
11
Handling and operation
SKRD 30 A1
GB
Handling and operation
In this section you receive important information for the handling and operation
of the device.
Switching On and Off
After the device has been connected to the power supply it is already switched
on. Via the On/Off
4
button you switch between the operational modes clock/
standby operation and radio.
NOTICE
The On/Off switch
4
does not disconnect the device completely from the
mains power. The device also consumes power when in Standby-Mode.
To completely disconnect the device from the mains power the mains
power cable plug
16
must be pulled from the mains socket.
Basic settings
After the device has been connected to the mains power supply it shows the time
of day and the day of the week in the display
3
. The device is in the operational
mode clock/standby operation.
Activating the settings menu
To activate the settings menu, whilst in the operational mode clock/standby operation,
press the Bass/AMS/Mode
7
button. The time of day, shown in the display
3
,
begins to blink. Each further actuation of the Bass/AMS/Mode
7
button switches
to the next setting potential. The menu item sequence is:
Setting the time of day
Setting the date
Setting the memory function
Setting the time of day format
Setting automatic display dimming.
Setting the display dimming’s switch on and off time.
NOTICE
The setting menu ends automatically if you do not actuate any buttons for
approx. 15 seconds. The executed setting is saved.
12
Handling and operation
SKRD 30 A1
GB
Setting the time
Prerequisite: The device is in the operational mode clock/standby operation.
Press the Bass/AMS/Mode
7
button once. The time of day indicator
begins to blink.
Set with the buttons Tune+
13
and Tune–
12
the current time of day. With
each button press the time of day changes by one minute. Holding down
the respective button for more than 2 seconds starts the speed setting.
Press the Bass/AMS/Mode
7
button again to save the current setting and
move to the next menu item.
NOTICE
The time of day will revert back to
o'clock if the device is disconnected
from the mains power supply and no battery is inserted or if the battery is too
weak.
Setting the date
Prerequisite: The device is in the operational mode clock/standby operation.
Press the Bass/AMS/Mode
7
button twice. The date indicator begins to
blink.
Set with the buttons Tune+
13
and Tune–
12
the current date. With each
button press the date is changed by one day. The weekday indicator changes
automatically. Holding down the respective button for more than 2 seconds
starts the speed setting.
Press the Bass/AMS/Mode
7
button again to save the current setting and
move to the next menu item.
NOTICE
The date will revert back to
, if the device is disconnected from the
mains power supply and no battery is inserted or if the battery is too weak.
Setting the memory function
You can set up to 10 date reminders to which an automatic reminder will be
triggered. The function SdA (SdA=Special Day Alert) is useful as a reminder, for
example, of birthdays or other recurring events. The reminder occurs every year
on the same date.
Prerequisite: The device is in the operational mode clock/standby operation.
Press the Bass/AMS/Mode
7
button three times. The current setting of the
selected reminder date is shown alternating with the indicator . Next to
the indicator
is the number of the memory slot for that date. Possible
reminders are
to .
13
Handling and operation
SKRD 30 A1
GB
Select with the buttons Preset+
11
and Preset–
10
the memory slot for the
date to be set.
Set with the buttons Tune+
13
and Tune–
12
the date for this memory slot.
With each button press the date is changed by one day. Holding down the
respective button for more than 2 seconds starts the speed setting.
NOTICE
Press the Dimmer/AOT
5
button if you want to switch off the date
for the currently set date. The reminder now occurs every year on the
same date. . To deactivate the memory function, programme in a date
that lies in the past.
Press the button Lock/Mem.
6
to set the time of day at which the reminder
function is to be triggered. The setting is carried out with the buttons Tune+
13
and Tune–
12
on the hour between 00 and 23. This setting applies to all
programmed reminder dates
Press the Bass/AMS/Mode
7
button again to save the current setting and
move to the next menu item.
Setting the time of day format
Prerequisite: The device is in the operational mode clock/standby operation.
Press the Bass/AMS/Mode
7
button four times. The current setting for the
time of day format is shown ( =24 hour format or =12 hour format).
With the button Tune+
13
set the time of day format to if you want a time
of day display in the 24 hour format .
With the button Tune–
12
set the time of day format to if you want a time
of day display in the 12 hour format .
Press the Bass/AMS/Mode
7
button again to save the current setting and
move to the next menu item.
Setting automatic display dimming.
Prerequisite: The device is in the operational mode clock/standby operation.
Press the Bass/AMS/Mode
7
button fi ve times. The current setting for the
automatic display dimming is shown ( = function switched on or =
function switched off ).
With the button Tune+
13
set the function if the display illumination
should be switched on and off at a setable time.
With the button Tune–
12
set the function if the display illumination is
to be switched on permanently.
Press the Bass/AMS/Mode
7
button again to save the current setting and
move to the next menu item.
14
Handling and operation
SKRD 30 A1
GB
Setting the display dimming’s switch on and off time
Prerequisite: The device is in the operational mode clock/standby operation.
Press the Bass/AMS/Mode
7
button six times. The current setting for the
display dimming switch on time is shown (
= display illumination
dims at 11 o’clock pm (23:00)).
Set with the buttons Tune+
13
and Tune–
12
the desired time of day. With
each button press the time of day changes by one minute. Holding down
the respective button for more than 2 seconds starts the speed setting.
Press the Bass/AMS/Mode
7
button again to save the current setting
and move to the switch off time setting. The current setting for the display
dimming switch off time is shown ( = display illumination switches
on again at 6 o’clock am (6:00)).
Set with the buttons Tune+
13
and Tune–
12
the desired time of day. With
each button press the time of day changes by one minute. Holding down
the respective button for more than 2 seconds starts the speed setting.
Press the Bass/AMS/Mode
7
button again to save the current setting
and exit the setting menu. The current time of day is shown.
Kitchen timer
The device has a convenient kitchen timer with which, for example, cooking and
baking times can be monitored. The programmable time range of the kitchen
timer lies between 1 minute and 23 hours, 59 minutes.
Setting the kitchen timer
Press the Snooze/Timer
14
button. The display shows . In the right
upper corner of the display
3
the saucepan symbol for the kitchen timer is
superimposed.
Turn the VOLUME
14
knob to set the time range for the kitchen timer.
Turning in a clockwise direction increases the time; turning in a counter
clockwise direction reduces the time.
NOTICE
If, during the setting, approx. 15 seconds passes without any changes
taking place the device reverts back to the previous operational mode.
15
Handling and operation
SKRD 30 A1
GB
Starting the kitchen timer
After setting the time press the button Snooze/Timer
14
again. The displayed
time begins to run backwards. In the right, upper corner of the display
3
a
backwards running clock is superimposed.
NOTICE
If, during the operation of the kitchen timer, another function is selected
the display of the remaining time fades out. The saucepan symbol and
the backwar
d running clock in the right, upper corner of the display
3
,
however, continue to be shown. Press the button Snooze/Timer
14
again to
allow the remaining time of the kitchen timer to be shown once more.
30 seconds before the kitchen timer run time has expired the device begins to
acoustically indicate, with individual signal tones, the arrival of the set time. Thereby
the interval between the individual tones becomes shorter and shorter. When the
set time has arrived the kitchen timer’s alarm signal sounds as a continuous tone.
Press the button Snooze/Timer
14
to switch off the kitchen timer alarm signal.
Pausing the kitchen timer.
Press, while the kitchen timer is running, the button Snooze/Timer
14
. The
kitchen timer is paused. The displayed remaining time begins to blink.
NOTICE
After approx. 15 seconds the device reverts back to the previous operational
mode. Press the button Snooze/Timer
14
again to allow the remaining time
of the kitchen timer to be shown once more.
To restart the kitchen timer press the button Snooze/Timer
14
again. The
kitchen timer restarts.
To switch off the kitchen timer before the set time has expired press and hold
down the Snooze/Timer
14
button for at least 2 seconds.
16
Handling and operation
SKRD 30 A1
GB
Programming the kitchen timer
You can preprogramme the kitchen timer with the most frequently used times so
that it is not necessary to continually reenter them. Up to 10 times can be prepro-
grammed. All 10 memory slots are preprogrammed with 10 minutes as standard.
For the programming of the kitchen timer proceed as follows:
Press the button Snooze/Timer
14
to activate the kitchen timer.
Turn the VOLUME
14
knob to set the time to be programmed. Turning in a
clockwise direction increases the time; turning in a counter clockwise direc-
tion reduces the time.
Press the button Lock/Mem.
6
to activate the timer selection. Under the
kitchen timer saucepan symbol a blinking is shown.
Select with the buttons Preset+
11
and Preset–
10
a memory slot between
and for the timer that is to be set.
Press the button Lock/Mem.
6
again to programme the set time on the
selected memory slot. The blinking under the saucepan symbol is now show-
ing constantly.
Repeat the process for the other memory slots.
Accessing the kitchen timer
To access a programmed time for the kitchen timer proceed as follows:
Press the button Snooze/Timer
14
to activate the kitchen timer.
Select with the buttons Preset+
11
and Preset–
10
the desired timer between
and .
Press the button Snooze/Timer
14
again to start the kitchen timer.
17
Handling and operation
SKRD 30 A1
GB
Programming alarm wake times
The device has two alarms available. All settings for both alarms can be carried
out independently from each other. You can select whether at the programmed
time an alarm tone shall sound or the radio shall play.
NOTICE
If, during alarm wake programming, no button is pressed for approx.
15 seconds the alarm will activate with the current settings.
Prer
equisite: The device is in the operational mode clock/standby operation.
To set the wake time proceed as follows:
Press the Alarm1 button
8
or the Alarm2 button
9
. The set wake time
of the respective alarm is shown blinking in the display
3
and the indicator
and/or appears. The weekday on which this alarm is to be activated is
shown above the time indicator.
Set with the buttons Tune+
13
and Tune–
12
the desired wake time. With
each button press the wake time changes by one minute. Holding down the
respective button for more than 2 seconds starts the speed setting.
Press the button Dimmer/AOT
5
to switch between the weekday combina-
tions Mo-Fr, Sa-Su or Mo-Su. The respective selected combination is shown
above the wake time.
Press and hold down the button Dimmer/AOT
5
for at least 2 seconds to
switch between the weekday combinations and individual weekday setting
alternatives.
NOTICE
With the individual weekday setting alternative you switch between
the days of the week with t
he button Dimmer/AOT
5
.
Press the Alarm1 button
8
and/or the Alarm2 button
9
to save the set
weekday combination and move to the setting of the alarm type (tone or radio).
Wake with alarm tone
Prerequisite: The device is in the operational mode clock/standby operation.
To select “Alarm tone” for the respective alarm press the Alarm1 button
8
or the Alarm2 button
9
several times in succession until, in the display
3
,
the symbol
appears.
18
Handling and operation
SKRD 30 A1
GB
Waken with radio
If you want to be woken by the radio, before activating the wake time carry out
the following settings:
Switch the radio on by pressing the On/Off
4
button.
Select the station with which you want to be woken (see section
Station setting).
With the VOL
UME
14
knob set the desired volume (see section
Volume settings).
Switch the radio off by pressing the On/Off
4
button.
To select “Radio” for the respective alarm press the Alarm1 button
8
or
the Alarm2 button
9
several times in succession until, in the display
3
, the
symbol
appears.
Switching the alarm off
Prerequisite: The device is in the operational mode clock/standby operation.
To switch off the respective alarm press the Alarm1 button
8
or the Alarm2
button
9
several times in succession until no symbols are shown in the
display
3
.
When the wake time has arrived
With the setting Wake with alarm tone” a fourfold signal tone sounds
in intervals of 2 seconds. The volume of the signal tone will continually increase
until the maximum volume has been reached. The duration of the wake signal is
restricted to 10 minutes.
With the setting Wake with radio” the radio will switch on. The previously
selected station will be activated for a maximum of 60 minutes at the set volume.
Press the button Snooze/Timer
14
to activate a repeat wake after 9 minutes.
NOTICE
The repeat wake function is possible up to 60 minutes after the set wake
time has arrived.
Press the Alarm1 button
8
or the Alarm2 button
9
to end the current
alarm.
NOTICE
The alarm becomes active again when the next wake time has arrived
(i.e. on the next day).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132

Silvercrest SKRD 30 A1 Operating Instructions Manual

Categorie
Ceasuri cu alarmă
Tip
Operating Instructions Manual