Ubiquiti UVC-G3 Ghid de inițiere rapidă

1080p Indoor/Outdoor

IP Camera with Infrared

Model: UVC-G3

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi® Video

Camera G3. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

UVC-G3

PoE Adapter (24V, 0.5A)

with Mounting Bracket*

Power Cord*

Cable Gland

Screw Anchors

(Qty. 2, 8 x 40 mm)

Self-Tapping Screws

(Qty. 2, M4 x 30)

1080p FHD Indoor/Outdoor

Surveillance Camera with

Built-In Infrared

Model: UVC-G3

Pole Mount

Bracket

Machine Screws

(Qty. 2, M4x10)

Quick Start

Guide

* Only the single-pack of the UVC-G3 includes a PoE adapter and a

power cord.

Installation Requirements

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet

cable and earth grounding must be used for outdoor installations as conditions of product

warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility

to follow local country regulations.

Hardware Overview

24V 0.5A PoE

M/N: UVC-G3

RESET

Mounting Base

Cable Gland

Tilt/Mount Lock

Adjustable Base

Camera Lock

Camera Lens

IR LED

Ethernet

Reset

Ethernet Connects to the Ubiquiti PoE adapter or UniFi

Switch for 24V passive PoE power and data.

Reset To reset to factory defaults, press and hold the Reset

button for more than 10 seconds while the camera is already

poweredon.

Hardware Installation

The UniFi Video Camera G3 can be mounted on a wall, ceiling,

or pole. Follow the appropriate steps for your installation:

Wall/Ceiling Mount

1. Remove the Mounting Base from the camera by turning the

Tilt/Mount Lock counterclockwise.

2. Mark the mounting holes on the wall or ceiling.

Cable

Slot

Note: If you are running the cable along the wall or

ceiling, ensure that you position the Cable Slot towards

the direction you want the cabling to run.

3. Use a 7 mm drill bit to drill the mounting holes in the wall

or ceiling.

Note: If

you are running the Ethernet cable through

the wall, cut a hole centered between the mounting

holes that is large enough to feed the cable through.

4. Insert a Screw Anchor into each mounting hole.

5. If you are feeding the Ethernet cable through the wall or

ceiling, do so now and feed it through the Mounting Base.

If not, feed the Ethernet cable through the Mounting Base

and place the cable in the Cable Slot.

6. Fasten the Mounting Base to the wall or ceiling using two

Self-Tapping Screws.

7. Remove the camera from the Adjustable Base by turning

the Camera Lock counterclockwise.

8. Feed the Ethernet cable through the Cable Gland and

Adjustable Base. Then connect the cable to the Ethernet Port

on the camera.

M/N: UVC-G3 24V 0.5A PoE

RESET

9. Connect the camera back to the Adjustable Base by turning

the Camera Lock clockwise.

10. Set the pan angle of the Adjustable Base while connecting

it to the Mounting Base. Then lock the camera to the

Mounting Base by turning the Tilt/Mount Lock clockwise.

Pole Mount

To mount the UVC-G3 on a pole, a metal strap or hose clamp is

required (not included).

1. Feed the metal strap through the slots on the Pole Mount

Bracket.

2. Wrap the metal strap around the pole and tighten the strap

by turning the screw clockwise.

3. Remove the Mounting Base from the camera by turning the

Tilt/Mount Lock counterclockwise.

4. Feed the Ethernet cable through the Mounting Base.

5. Fasten the Mounting Base to the Pole Mount Bracket using

two Machine Screws.

6. Remove the camera from the Adjustable Base by turning

the Camera Lock counterclockwise.

7. Feed the Ethernet cable through the Cable Gland and

Adjustable Base. Then connect the cable to the Ethernet Port

on the camera.

M/N: UVC-G3 24V 0.5A PoE

RESET

8. Connect the camera back to the Adjustable Base by turning

the Camera Lock clockwise.

9. Set the pan angle of the Adjustable Base while connecting

it to the Mounting Base. Then lock the camera to the

Mounting Base by turning the Tilt/Mount Lock clockwise.

Connecting Power over Ethernet

Note: PoE adapters are not included with the UVC-G3

5-pack. Multiple cameras may be powered by a UniFi

Switch using 24V passive PoE.

1. Connect the Ethernet cable from the camera to the POE

port on the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the LAN port

on the PoE Adapter.

3. Connect the Power Cord to the PoE Adapter. Connect the

other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the mounting slots on the adapter with the mounting

tabs on the bracket, and then slide the adapter down.

*640-00175-04*

640-00175-04

UniFi Video

Ensure that you are running UniFiVideo software version 3.2

or higher. The latest version of the UniFi Video software is

available at downloads.ubnt.com/unifivideo

The UniFi Video auto-management feature should

automatically detect your new camera(s). To manage the

camera, perform the following steps:

1. Click the Unmanaged tab.

2. Click the camera row.

3. The Camera Details window will appear on the right side of

the screen. Enter ubnt in the Username and Password fields

and click Manage.

The camera will appear in the Managed cameras list.

Note: You may need to update the firmware from the

Firmware tab to complete the camera installation.

UniFi Video App

The UniFi Video mobile app is available for free in

the App Store for iOS devices and the Play Store for

Android-based devices.

For details on using the UniFi Video software, refer to the User

Guide at: documentation.ubnt.com/unifivideo

Adjusting the Camera View

1. Loosen the Tilt/Mount Lock by turning it counterclockwise.

Tilt the camera to adjust the angle and rotate it to level

the view.

2. To adjust the pan angle or third axis, loosen the Tilt/Mount

Lock completely and reseat the Adjustable Base at the

desired angle.

3. Lock the view by turning the Tilt/Mount Lock clockwise.

Specifications

UVC G3

Dimensions

Ø 75 x 140 mm

(2.95 x 5.51")

Weight 300 g

(10.58 oz)

Enclosure Injection-Molded Polycarbonate and

Die-Cast Aluminum

Sensor 1/3" 4-Megapixel HDR Sensor

Lens EFL 3.6 mm, f/1.8

Viewing Angle

Before Lens Correction

After Lens Correction

85° (H), 44.8° (V), 98.1° (D)

72° (H), 42.9° (V), 80.4° (D)

Night Mode IR LEDs with Mechanical ICR Filter

Video Compression H.264

Resolution 1080p FHD (1920x1080)

Maximum Frame Rate 30 FPS

Image Settings Brightness, Contrast, Sharpness, Saturation,

Noise Reduction, 50/60 Hz

Processor Specs Ambarella S2L63 (816 MHz ARM Cortex-A9)

Memory Information 512 MB DDR3L

Management Interface UniFi Video v3

Networking Interface (1) 10/100 Ethernet Port

Microphone Yes

Max. Power Consumption 4W

Power Method Passive PoE (24V)

Power Supply 24V, 0.5A PoE Adapter (Included)

Buttons Factory Reset Button

Mounting Wall/Ceiling Mount

Operating Temperature -30 to 70° C

-22 to 158° F

Operating Humidity 20 to 90% Noncondensing

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Hot surface. Do not touch.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Pagina se încarcă ...

Ubiquiti UVC-G3 Ghid de inițiere rapidă

Ubiquiti UVC-G3 Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente