Ubiquiti Networks UniFi Manualul utilizatorului

Marca: Ubiquiti Networks

Model: UniFi

Categorie: Accesorii camere

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

720p Indoor/Outdoor

IP Camera with Infrared

Model: UVC

Introduction

Thank you for purchasing the Ubiquiti Networks

™

UniFi®

Video Camera. This Quick Start Guide is designed to guide you

through the installation of the UniFi Video Camera and show

you how to access the Camera Configuration Interface. This

Quick Start Guide also includes the warranty terms.

The UniFi Video software and User Guide are available for

download at downloads.ubnt.com/unifivideo

Package Contents

Camera PoE Adapter

(24V, 0.5A)

Power Cord Hex Key Metal Strap

720p Indoor/Outdoor

IP Camera with Infrared

Model: UVC

Screws

(M4x30, Qty. 4)

Screw Anchors

(Qty. 4)

Mounting

Template

Quick Start Guide

Wall-Mounting Requirements

• Drill

• Drill bit, 7 mm

• Phillips screwdriver

Pole-Mounting Requirements

• Screwdriver or 7 mm socket driver

product warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, and Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

Side View

Adjusts Camera Up or Down

Rotates Camera Rotates Base

Sun Shade

Bottom View

24V 0.5A POE

M/N: UVC

Video Camera

Port Cover

microSD Card Slot

Ethernet Port

Ethernet Seal

LEDs

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and flash

when there is activity.

Power The Power LED will light steady amber when

the camera is connected to a power source.

Before You Begin

A few notes about the camera before you begin installation:

• If you wish to use the sun shade, it is easier to engage before

you install the camera.

• The camera has an adjustable base, tilt, and camera rotation.

• The camera should never be pointing straight up or straight

down. Always ensure it is at least two clicks from the straight

up or down position.

• When mounted outdoors, there should be a 150 mm (6")

drip loop to prevent water from creeping along the cable to

the camera.

Protective Plastic Film

After installation, remove the protective plastic film covering

the camera lens and the IR LEDs.

Camera Lens Film

IR LEDs Film

Sun Shade

Lock and Release Tab

Sun Shade

If you want to use the Sun Shade, press the Sun Shade Lock and

Release Tab from behind the camera and slide the Sun Shade

forward until it locks into place.

Sun Shade Sun Shade Lock and Release Tab

*640-00069-04*

640-00069-04

Installation Overview

The installation process differs depending on if you are

mounting the camera on a pole or on a wall. Follow the

instructions for the installation that you are performing.

Below is an overview of the steps:

• Connect one end of the Ethernet cable to the camera.

• Insert a microSD card (optional).

• Perform the camera mounting steps (Wall Mount or

Pole Mount).

• Connect the other end of Ethernet cable to the PoE Adapter

or a Ubiquiti Networks TOUGHSwitch

™

Connect Ethernet to the UniFi Video Camera

1. Press the latch to open the Port Cover on the bottom of

the camera.

24V 0.5A POE

M/N: UVC

Video Camera

2. (Optional) Insert a microSD card into the microSD Card Slot.

24V 0.5A POE

M/N: UVC

Video Camera

3. Connect an Ethernet cable to the Ethernet port on the

camera.

24V 0.5A POE

M/N: UVC

Video Camera

4. Remove the Ethernet Seal from the Port Cover.

5. Slide the Port Cover back onto the camera near the

Ethernet port and snap it in place.

6. Wrap the Ethernet Seal around the Ethernet cable and press

it into the Port Cover.

Wall Mount

1. Remove the adhesive Mounting Template from the backing

and place the label on the wall where you want the camera.

2. Use a 7 mm drill bit to drill the holes in the wall.

3. Insert the four Screw Anchors into the wall.

4. Use a Phillips screwdriver to secure the camera to the wall

with the four Screws.

Proceed to Connecting Power over Ethernet.

Pole Mount

To mount the UniFi Video Camera on a pole, use the included

Metal Strap:

1. Open the Metal Strap by turning the locking screw

counter-clockwise.

2. Slide the Metal Strap through the base of the camera.

3. Wrap the Metal Strap around the pole. Use a screwdriver or

7 mm socket drive to turn the locking screw clockwise and

securely fasten the strap to the pole.

Connecting Power over Ethernet

1. Connect the other end of the Ethernet cable to one of the

following:

• PoE Adapter Connect the UniFi Video Camera to the

Ethernet port labeled POE on the included PoE Adapter.

• EdgeSwitch (shown below) or TOUGHSwitch Connect the

UniFi Video Camera to a port with 24V power enabled

and skip steps 2 and 3.

2. Connect an Ethernet cable from your LAN to the Ethernet

port labeled LAN on the PoE Adapter.

3. Connect the power cord to the power port on the PoE

Adapter. Connect the other end of the power cord to a

power outlet.

UniFi Video

The UniFI Video software is pre-installed on the UniFi NVR

(sold separately). If you do not have the UniFi NVR, you can

download and install the latest version of the UniFi Video

software at downloads.ubnt.com/unifivideo; the UniFi Video

auto-management feature should automatically detect and

install your new camera(s).

Proceed to Adjusting the Camera View.

For details on using the UniFi Video software, refer to the User

Guide at documentation.ubnt.com/unifivideo

Camera Configuration Interface

Access the Camera Configuration Interface if you have not

yet installed the UniFi Video software, or plan to use the UniFi

Video Camera as a stand-alone camera without the UniFi

Video software.

1. Ensure that your host machine is connected to the same

LAN as the UniFi Video Camera.

2. The UniFi Video Camera is set to DHCP by default. If you

have a router or DHCP server providing addresses on your

network, please check your DHCP Client Table or download

the Ubiquiti Discovery Tool from:

http://www.ubnt.com/download#app

Note: If you do not have a DHCP server, the camera

defaults to the IP address 192.168.1.20.

3. Launch your web browser, and in the address field, type

https:// and then the IP address of the camera, for example:

https://192.168.1.20. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields and click Login.

5. The Main screen will appear and you should see a live

video stream from the UniFi Video Camera.

Adjusting the Camera View

Adjust Camera

Up or Down

Rotate Camera

Rotate

Base

Note: Remove the protective plastic film from the

camera lens and IR LEDs.

For details on using the UniFi Video software, refer to the User

Guide at: documentation.ubnt.com/unifivideo

Specifications

UniFi Video Camera

Dimensions 225 x 75 x 75 mm (8.85 x 2.95 x 2.95")

Weight 373 g (13.1 oz)

Ports (1) 10/100 Ethernet Port, microSD Card Slot

Sensor Progressive Scan RGB CMOS ¼"

Lens 3.6 mm/ F1.8

Power LED Amber

Link/Activity LED Green

Buttons Factory Reset Button

Power Method Passive Power over Ethernet (12-24V)

Power Supply 24V, 0.5A PoE Adapter Included

Max. Power Consumption 4.5 W

Certications CE, FCC, IC

Mounting Pole/Wall/Ceiling

Operating Temperature -30 to 50° C (-22 to 122° F)

Operating Humidity 20 - 90% Noncondensing

Video

Video Compression H.264

Resolution 1 MP/HDTV 720p

Maximum Frame Rate 30 FPS

Image Setting

Brightness, Contrast, Sharpness, Saturation,

Noise Reduction, 50/60 Hz

General

Processor ARM 1136J-S, 528 MHz

Memory 256 MB DDR3

View Angle 56.14° (H)

36.86° (V)

64.33° (D)

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian CAN ICES-3(B).

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Cet appareil numérique de la classe A est confrome à la norme NMB-3(B)

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

Australia and New Zealand

Warning: This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

Pagina se încarcă ...

Ubiquiti Networks UniFi Manualul utilizatorului

Marca: Ubiquiti Networks

Model: UniFi

Categorie: Accesorii camere

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ubiquiti Networks UniFi User guide
italiano: Ubiquiti Networks UniFi Guida utente

Ubiquiti Networks UniFi Manualul utilizatorului

Acest manual este potrivit și pentru

Ubiquiti Networks UniFi Manualul utilizatorului

în alte limbi

Lucrări conexe

Alte documente