Tesla TM36AF21-1232IA Split-type Air Conditioning Manual de utilizare

SPLIT-TYPE

AIR CONDITIONER

USER

MANUAL

Ver. 2022

MKD

BIH/

MNE RO SLO SRBENG BG GR HR HU

For R32 DC Inverter models:

TM36AF21-1232IA

TM28AF21-0932IAW

TM36AF21-1232IAW

TM52AF21-1832IAW

TM70AF21-2432IAW

TM36I13-1232IAWUV

TM53I13-1832IAWUV

TM70I13-2432IAWUV

Ver. 2022

HASZNÁLATI UTASÍTÁS

Megjegyzés: A használati utasításban található összes kép csak illusztráció, a tényleges termék ezektől

eltérhet. Kérjük, hogy a készülék beüzemelése előtt ﬁgyelmesen olvassa el ezt az útmutatót és őrizze meg

későbbi felhasználásra is.

HUN

OPERATING INSTRUCTION

Note: All the pictures in this manual are just schematic diagrams, the actual is the standard. Please read

this owner’s manual carefully and thoroughly before operating the unit! Take care of this manual for future

reference.

UPUTE ZA UPOTREBU

Napomena: Sve slike u ovom priručniku su samo shematski dijagrami, ﬁzički proizvod je standard. Molimo

Vas da pažljivo i temeljito pročitate ovo uputstvo za upotrebu prije korištenja uređaja! Čuvajte ovaj priručnik

za buduće korištenje.

ΕΓΧΕΙΡΙΔΙΟ ΧΡΉΣΉΣ

Σημείωση: Οι εικόνες στο παρόν εγχειρίδιο είναι σχεδιαγράμματα, ανατρέξτε στο πραγματικό προϊόν. Διαβάστε

προσεκτικά τις προφυλάξεις στο παρόν εγχειρίδιο προτού θέσετε τη μονάδα σε λειτουργία! Φυλάξτε το παρόν

εγχειρίδιο για μελλοντική χρήση.

ИНСТРУКЦИЯ ЗА УПОТРЕБА

Забележка: Всички снимки в тази инструкция са само схематични диаграми, действителните са

стандартните. Моля, прочетете внимателно тази инструкция за употреба преди да започнете работа с

уреда! Запазете тази инструкция за бъдещи справки

ENG

HR

GR

BG

UPUTSTVO ZA UPOTREBU

Napomena: Sve slike u ovom priručniku su samo šematski dijagrami, ﬁzički proizvod je standard. Molimo Vas

da pažljivo i temeljno pročitate ovo uputstvo za upotrebu prije korišćenja uređaja! Sačuvajte ovo uputstvo za

buduću upotrebu.

BIH/

MNE

PRIROČNIK ZA UPORABO

Opomba: Vse slike v tem priročniku so le shematske risbe, dejansko stanje je standard. Prosimo, da pred

uporabo skrbno in temeljito preberete ta priročnik za uporabo! Priročnik shranite za kasnejšo uporabo.

MANUAL DE UTILIZARE

Nota: Fotograﬁile din acest manual sunt doar diagrame schematice. Vă rugăm să citiți “Manualul de Utilizare”

cu atenție, înainte de a utiliza aerul condiționat, pentru a asigura funcționarea corespunzătoare. Păstrați

manualul pentru referințe ulterioare.

SLO

RO

УПАТСТВО ЗА УПОТРЕБА

Напомена: Сите слики во овој прирачник се само шематски дијаграми, физичкиот производ е

стандард. Ве молиме внимателно и теменлно да го причитате ова упатство за употреба пред

користење на уредот! Сочувајте го ова упатство за идна употреба.

MKD

UPUTSTVO ZA UPOTREBU

Napomena: Sve slike u ovom priručniku su samo šematski dijagrami, ﬁzički proizvod je standard. Molimo

Vas da pažljivo i temeljno pročitate ovo uputstvo za upotrebu pre korišćenja uređaja! Sačuvajte ovo

uputstvo za buduću upotrebu.

SRB

3

ENG

• Read this guide before installing and using the appliance.

• During the installation of the indoor and outdoor units the access to the working area should be forbidden to

children. Unforeseeable accidents could happen.

• Make sure that the base of the outdoor unit is ﬁrmly ﬁxed.

• Check that air cannot enter the refrigerant system and check for refrigerant leaks when moving the air

conditioner.

• Carry out a test cycle after installing the air conditioner and record the operating data.

• Protect the indoor unit with a fuse of suitable capacity for the maximum input current or with another overload

protection device.

• Ensure that the mains voltage corresponds to that stamped on the rating plate. Keep the switch or power plug

clean. Insert the power plug correctly and ﬁrmly into the socket, thereby avoiding the risk of electric shock or

ﬁre due to insufﬁcient contact.

• Check that the socket is suitable for the plug , otherwise have the socket changed.

• The appliance must be ﬁtted with means for disconnection from the supply mains having a contact separation

in all poles that provide full disconnection under overvoltage category III conditions, and these means must be

incorporated in the ﬁxed wiring in accordance with the wiring rules.

• The air conditioner must be installed by professional or qualiﬁed persons.

• Do not install the appliance at a distance of less than 50 cm from inﬂammable substances (alcohol, etc.) or from

pressurised containers (e.g. spray cans).

• If the appliance is used in areas without the possibility of ventilation, precautions must be taken to prevent any

leaks of refrigerant gas from remaining in the environment and creating a danger of ﬁre

• The packaging materials are recyclable and should be disposed of in the separate waste bins .Take the air

conditioner at the end of its useful life to a special waste collection centre for disposal.

• Only use the air conditioner as instructed in this booklet. These instructions are not intended to cover every

possible condition and situation . As with any electrical household appliance , common sense and caution are

therefore always recommended for installation, operation and maintenance.

• The appliance must be installed in accordance with applicable national regulations.

• Before accessing the terminals , all the power circuits must be disconnected from the power supply.

• The appliance shall be installed in accordance with national wiring regulations.

• This appliance can be used by children aaged from 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall

not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Do not try to install the conditioner alone; always contact specialized technical personnel.

• Cleaning and maintenance must be carried out by specialized technical personnel. In any case disconnect the

appliance from the mains electricity supply before carrying out any cleaning or maintenance.

• Ensure that the mains voltage corresponds to that stamped on the rating plate. Keep the switch or power plug

clean. Insert the power plug correctly and ﬁrmly into the socket , thereby avoiding the risk of electric shock or

ﬁre due to insufﬁcient contact.

• Do not pull out the plug to switch off the appliance when it is in operation, since this could create a spark and

cause a ﬁre, etc.

• This appliance has been made for air conditioning domestic environments and must not be used for any other

purpose , such as for drying clothes, cooling food, etc.

• Always use the appliance with the air ﬁlter mounted . The use of the conditioner without air ﬁlter could cause an

excessive accumulation of dust or waste on the inner parts of the device with possible subsequent failures.

• The user is responsible for having the appliance installed by a qualiﬁed technician , who must check that it is

earthed in accordance with current legislation and insert a thermomagnetic circuit breaker.

• The batteries in remote controller must be recycled or disposed of properly. Disposal of Scrap Batteries ---

Please discard the batteries as sorted municipal waste at the accessible collection point.

• Never remain directly exposed to the ﬂow of cold air for a long time. The direct and prolonged exposition

SAFETY RULES AND RECOMMENDATIONS

FOR THE INSTALLER

SAFETY PRECAUTIONS

4

ENG

to cold air could be dangerous for your health .Particular care should be taken in the rooms where there are

children , old or sick people.

• If the appliance gives off smoke or there is a smell of burning, immediately cut off the pow er supply and contact

the Service Centre.

• The prolonged use of the device in such conditions could cause ﬁre or electrocution.

• Have repairs carried out only by an authorised Service Centre of the manufacturer . Incorrect repair could

expose the user to the risk of electric shock, etc.

• Unhook the automatic switch if you foresee not to use the device for a long time. The airﬂow direction must be

properly adjusted.

• Only use the air conditioner as instructed in this booklet. These instructions are not intended to cover every

possible condition and situation. As with any electrical household appliance, common sense and caution are

therefore always recommended for installation , operation and maintenance.

• Ensure that the appliance is disconnected from the power supply when it will remain inoperative for a long

period and before carrying out any cleaning or maintenance.

• Selecting the most suitable temperature can prevent damage to the appliance.

• Do not bend, tug or compress the power cord since this could damage it. Electrical shocks or ﬁre are probably

due to a damaged power cord. Specialized technical personnel only must replace a damaged power cord.

• Do not use extensions or gang modules.

• Do not touch the appliance when barefoot or parts of the body are wet or damp.

• Do not obstruct the air inlet or outlet of the indoor or the outdoor unit. The obstruction of these openings

causes a reduction in the operative efﬁciency of the conditioner with possible consequent failures or damages.

• In no way alter the characteristics of the appliance.

• Do not install the appliance in environments where the air could contain gas , oil or sulphur or near sources of

heat.

• This appliance is not intended for use by persons (including children ) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

• Do not climb onto or place any heavy or hot objects on top of the appliance.

• Do not leave windows or doors open for long when the air conditioner is operating.

• Do not direct the airﬂow onto plants or animals.

• A long direct exposition to the ﬂow of cold air of the conditioner could have negative effects on plants and

animals.

• Do not put the conditioner in contact with water. The electrical insulation could be damaged and thus causing

electrocution.

• Do not climb onto or place any objects on the outdoor unit

• Never insert a stick or similar object into the appliance. It could cause injury.

• Children should be supervised to ensure that they do not play with the appliance. If the supply cord is damaged,

it must be replaced by the manufacturer,its service agent or similarly qualiﬁed persons in order to avoid a

hazard.

SAFETY RULES AND PROHIBITIONS

5

ENG

NAMES OF PARTS

Indoor unit

Outdoor unit

Note: This ﬁgure shown may be

different from the actual object.

Please take the latter as the

standard.

Mounting plate

Air ﬁlter

Air inlet

Front panel

Emergency button

Refrigerant

connecting pipe

Air inlet

Air outlet

Air outlet Air deﬂector and ﬂap

Wiring cover

Drainage pipe

Connection wiring

Valve protective cover

Gas valve

(Low pressure valve)

Liquid valve

(High pressure valve)

With the protective

cover removed

6

ENG

REMOTE CONTROLLER

Remote control DISPLAY

ON/OFF

Turns the unit on or off.

MODE

Scrolls through operation

modes as follows: AUTO ->

COOL -> DRY-> HEAT ->FAN

NOTE: HEAT mode is not

supported by the cooling only

appliance.

ECO/GEAR

Press this button to enter the

energy efﬁcient mode in a

sequence of following:

ECO -> GEAR (75%) -> GEAR

(50%) -> Previous setting

mode -> ECO ......

OK

Used to conﬁrm the selected

functions

TIMER

Set timer to turn unit on or off

SHORTCUT

Used to restore the current

settings or resume previous

settings.

CLEAN

Used to start/stop the Self

Clean or Active Clean function.

LED

Turns indoor unit’s LED display

and air conditioner buzzer on

and off (model dependent),

which create a comfortable

and quiet environment.

Turbo

Enables unit to reach preset

temperature in shortest

possible time

TEMP

Increases temperate in

1°C (1°F) increments. Max.

temperature is 30°C (86°F).

TEMP

Decreases temperature in

1°C (1°F) increments. Min.

temperature is

17°C (62°F).

FAN SPEED

Selects fan speeds in the

following order:

AUTO -> LOW -> MED ->

HIGH

NOTE: Holding this button

down for 2 seconds will

activate Silence feature.

SWING

Starts and stops the horizontal

louver movement. Hold down

for 2 seconds to initiate vertical

louver auto swing feature.

SET

Scrolls through operation

functions as follows:

Fresh ( ) -> Sleep ( ) ->

Follow Me ( ) ->

AP mode ( ) -> Fresh...

The selected symbol will

ﬂash on the display area,

press the OK button to

conﬁrm.

7

ENG

Remote Screen Indicators

Information are displayed when the remote controller is power up.

   

Breeze Away display

Active clean feature display

Fresh feature display

Sleep mode display

Follow me feature display

Wireless control feature display

Low battery detection display (If ﬂashes)

MODE display

Displays the current

including:

ECO display

Displays when ECO feature

is activated

GEAR display

Displays when GEAR

feature is activated

LOCK display

Displays when LOCK

feature is activated.

Temperature/Timer/Fan

speed display

Displays the set

temperature by default, or

fan speed or timer setting

when using TIMER ON/OFF

functions.

• Temperature range:

16-30ºC/60-86ºF/

(20-28ºC/68-82ºF)

(Model dependent)

• Timer setting range:

0-24 hours

• Fan speed setting range:

AU -100%

This display is blank when

operating in FAN mode.

FAN SPEED display

Displays selected fan

speed:

TIMER ON display

TIMER OFF display

Silence feature display

Transmission Indicator

Lights up when remote sends

signal to indoor unit

This fan speed can not be adjusted

in AUTO or DRY mode.

Note:

All indicators shown in the ﬁgure are for the purpose of clear presentation. But during the actaul operation, only the

relative function signs are shown on the display window.

Silence

LOW

MED

HIGH

AUTO

Horizontal louver

swing display

Vertical louver auto

swing display

TURBO mode display

Not available for this unit

8

ENG

Use 2 pieces LRO3 AAA (1.5V) batteries.

Do not use rechargeable batteries.

Replace the old batteries with new ones of the same type when the

display is no longer legible.

Do not dispose batteries as unsorted municipal waste.

Collection of such waste separately for special treatment is necessary.

Each time when insert the batteries in the remote controller for the ﬁrst time, you can set the Cooling only or

Heating pump control type. As soon as you insert the batteries, turn off the remote controller, and operate as

below.

1. Long press the button, until the ( ) icon ﬂash, to set the Cooling only type.

2. Long press the button, until the ( ) icon ﬂash, to set the Heating pump type.

Note: If you set the remote control in cooling mode, it will not be possible to activate the heating function in

units with a heating pump. If you need to reset, take out the batteries and install again.

You can program the temperature display between �C and �F.

1. Press and hold the button over 5 seconds to get into the change mode;

2. Press and hold the button, until it switch to �C and �F;

3. Then release the pressing and wait for 5 seconds, the function will be selected.

Replacement of Batteries

Remove the battery cover plate from the rear of the remote control, by pressing and sliding it in direction as the

arrow. Install the batteries by putting ( -) at the side with spring on the remote controller. Reinstall the battery cover

by sliding it into place.

Note:

1. Direct the remote control toward the Air conditioner.

2. Check that there are no objects between the remote control and the Signal receptor in the indoor unit.

3. Never leave the remote control exposed to the rays of the sun.

4. Keep the remote control at a distance of at least 1m from the television or other electrical appliances.

The cooling function allows the air

conditioner to cool the room and

reduce Air humidity at the same time.

Fan mode, air ventilation only.

To activate the cooling function (COOL), press the

button until the symbol appears on the

display. With the button or set a temperature lower

than that of the room.

To set the FAN mode, press until appears

on the display.

Cooling mode

FAN MODE (Not FAN button)

This function reduces the humidity

of the air to make the room more

comfortable.

To set the DRY mode, Press until appears

in the display. An automatic function of pre-setting is

activated.

DRY MODE

Automatic mode.

To set the AUTO mode, press until

appears on the display. In AUTO mode the run mode

will be set automatically according to the room

temperature.

AUTO MODE

9

ENG

The heating function allows the air

conditioner to heat the room.

Change the operating fan speed.

To automatic switch on the appliance.

To automatic switch off the appliance.

To activate the heating function (HEAT), press the

button until the symbol appears on the

display. With the button or set a temperature higher

than that of the room.

Press button to set the running fan speed, it can

be set to AUTO/ MUTE/ LOW/ LOW-MID / MID/ MID-

HIGH/ HIGH/ TURBO speed circularly.

When the unit is switch-off, you can set the TIMER ON.

To set the time of automatic switch-on as below:

1. Press button ﬁrst time to set the switch-on,

and will appear on the remote display and

ﬂashes.

2. Press or to button to set desired Timer-on time.

Each time you press the button, the time increases/

decreases by half an hour between 0 and 10 hours

and by one between 10 and 24 hours.

3. Press button second time to conﬁrm.

When the unit is switch-on, you can set the TIMER OFF.

To set the time of automatic switch-off, as below:

1. Conﬁrm the appliance is ON.

2. Press the button at ﬁrst time to set the

switch-off.

Press or to set the needed timer.

3. Press button at the second time to conﬁrm.

CANCEL it by press button.

Note: All programming should be operated within 5

seconds, otherwise the setting will be cancelled.

1. Press the button SWING to activate the louver,

1.1 Press to activate the horizontal ﬂaps to swing

from up to down, the will appear on the remote

display.

1.2 Press to active the vertical deﬂectors to swing

from left to right, the will appear on the remote

display.

1.3 Do it again to stop the swing movement at the

current angle.

2. If the vertical deﬂectors are positioned manually

which placed under the ﬂaps, they allow to move the

air ﬂow direct to rightward or leftward.

3. Long press or over 3 seconds to select more

angles of the airﬂow direction.

1. Long press and button together

to active this function, and do it again to deactivate

this function.

2. Under this function, no single button will active.

HEATING MODE

FAN SPEED function (FAN

button)

TIMER function ---- TIMER ON

TIMER function ---- TIMER OFF

SWING function

Child-Lock function

In HEATING operation, the appliance can

automatically activate a defrost cycle, which is

essential to clean the frost on the condenser so as to

recover its heat exchange function. This procedure

usually lasts for 2-10 minutes. During defrosting,

indoor unit fan stop operation. After defrosting, it

resumes to HEATING mode automatically.

(For North American market) If necessary, you

can press ECO button 10 times within 8 seconds

under heating mode to start the forced defrosting.

It will defrost the outdoor ice much more fast.

4. After Timer-on setting, set the needed mode (Cool/

Heat/ Auto/ Fan/ Dry), by press the button.

And set the needed fan speed, by press

button. And press or to set the needed operation

temperature.

CANCEL it by press button.

Never position Flaps manually, the delicate

mechanism might seriously damaged!

Never put ﬁngers, sticks or other objects into the

air inlet or outlet vents. Such accidental contact

with live parts might cause unforeseeable damage

or injury.

10

ENG

Follow me function ( ):

The FOLLOW ME function enables the remote control

to measure the temperature at its current location and

send this signal to the air conditioner every 3 minutes

interval.

When using AUTO, COOL or HEAT modes, measuring

ambient temperature from the remote control(instead

of from the indoor unit itself) will enable the air

conditioner to optimize the temperature around you

and ensure maximum comfort.

NOTE: Press and hold Turbo button for seven seconds

to start/stop memory feature of Follow Me function. If

the memory feature is activated, “On” displays for 3

seconds on the screen.

• If the memory feature is activated, “On” displays for

3 seconds on the screen

• If the memory feature is stopped, “OFF” displays for

3 seconds on the screen.

• While the memory feature is activated, press the ON/

OFF button, shift the mode or power failure will not

cancel the Follow me function.

AP function ( ) :

Choose AP mode to do wireless network conﬁguration.

For some units, it doesn’t work by pressing the SET

button. To enter the AP mode, continuously press the

LED button seven times in 10 seconds.

Breeze Away function ( ) (some units) :

This feature avoids direct air ﬂow blowing on the body

and makes you feel indulging in silky coolness.

NOTE: This feature is available under cool, Fan and Dry

mode only.

FRESH function ( ) (some units) :

When the FRESH function is initiated, the Ionizer/Plasma

Dust Collector(depending on models) is energized and

will help to remove pollen and impurities from the air.

Keep pressing Fan button for more

than 2 seconds to activate/disable

Silence Function (some units).

Due to low frequency operation

of compressor, it may result in

insufﬁcient cooling and heating

capacity. Press ON/OFF, Mode,

Sleep, Turbo or Clean button while

operating will cancel silence function

Press LED button

Press this button to turn on and turn

off the display on the indoor unit.

Press this button more than 5

seconds(some units)

Keep pressing this button more than

5 seconds, the indoor unit will display

the actual room temperature.

Press more than 5 seconds again

will revert back to display the setting

temperature.

Press X-ECO button to enter the

energy efﬁcient mode in a sequence

of following:

ECO -> GEAR(75%) -> GEAR(50%) ->

Previous setting mode -> ECO......

Note:This function is only available

under COOL mode.

Silence function

LED DISPLAY

ECO operation:

Under cooling mode, press this button, the remote

controller will adjust the temperature automatically

to 24ºC/75ºF, fan speed of Auto to save energy (only

when the set temperature is less than 24ºC/75ºF). If

the set temperature is above 24ºC/75ºF, press the

ECO button, the fan speed will change to Auto, the set

temperature will remain unchanged.

NOTE:

Pressing the ECO button, or modifying the mode or

adjusting the set temperature to less than 24ºC/75ºF

will stop ECO operation.

Under ECO operation, the set tmeperature should be

24ºC/75ºF or above, it may result in insufﬁcient cooling.

If you feel uncomfortable, just press the ECO button

again to stop it.

GEAR operation:

Press the ECO/GEAR button to enter the GEAR

operation as following:

75%(up to 75% electrial energy consumption)

50%(up to 50% electrial energy consumption)

Previous setting mode.

Under GEAR operation, the display on the remote

controller will alternage between electical energy

consumption and set temperature.

ECO/GEAR function

11

ENG

Attempt to use the air conditioner under the temperature beyond the speciﬁed range may cause the air

conditioner protection device to start and the air conditioner may fail to operate. Therefore, try to use the air

conditioner in the following temperature conditions.

Characteristics of heating operation (applicable to Heating pump)

Preheating:

When the heating function is enabled, the indoor unit will take 2~5 minutes for preheating, after that the air

conditioner will start heating and blows warm air.

Defrosting:

During heating, when the outdoor unit frosted, the air conditioner will enable the automatic defrosting function

to improve the heating effect. During defrosting, the indoor and outdoor fans stop running. The air conditioner

will resume heating automatically after defrosting ﬁnish.

With the power supply connected, restart the air conditioner after shutdown, or switch it to other mode during

operation, and the air conditioner protection device will start. The compressor will resume operation after 3

minutes.

Temperature Mode

Heating Cooling Dry

Room temperature 0°C~30°C17°C~32°C

Outdoor temperature

-20°C~30°C

(Low temperature heating:

-25°C~30°C)

T1 climate: 15°C~53°C

(Low temperature cooling: -15°C~53°C)

T3 climate: 15°C~55°C

Inverter air conditioner:

OPERATION INSTRUCTIONS

Emergency button:

Open the panel and ﬁnd the emergency button on the electronic control box when the remote controller fails .

(Always press the emergency button with insulation material.)

Current status Operation Respond Enter mode

Standby Press the emergency button once It beeps brieﬂy once. Cooling mode

Standby (Only for

heating pump)

Press the emergency button twice

in 3 seconds It beeps brieﬂy twice. Heating mode

Running Press the emergency button once It keeps beeping for a

while Off mode

control-box cover

(open the panel of indoor unit)

ON/OFF

12

ENG

INSTRUCTION FOR SERVICING (R32)

1. Check the information in this manual to ﬁnd out the dimensions of space needed for proper installation of the

device, including the minimum distances allowed compared to adjacent structures.

2. Appliance shall be installed, operated and stored in a room with a ﬂoor area larger than 4m2.

3. The installation of pipe-work shall be kept to a minimum.

4. The pipe-work shall be protected from physical damage, and shall not be installed in an unventilated space if

the space is smaller than 4m2 .

5. The compliance with national gas regulations shall be observed.

6. The mechanical connections shall be accessible for maintenance purposes.

7. Follow the instructions given in this manual for handling, installing, cleaning, maintaining and disposing of the

refrigerant.

8. Make sure ventilation openings clear of obstruction.

9. Notice:The servicing shall be performed only as recommended by the manufacturer.

10. Warning: The appliance shall be stored in a well-ventilated area where the room size corresponds to the room

area as speciﬁed for operation.

11. Warning:The appliance shall be stored in a room without continuously operating open ﬂames (for example

an operating gas appliance) and ignition sources (for example an operating electric heater).

12. The appliance shall be stored so as to prevent mechanical damage from occurring.

13. It is appropriate that anyone who is called upon to work on a refrigerant circuit should hold a valid and up-to-

date certiﬁcate from an assessment authority accredited by the industry and recognizing their competence

to handle refrigerants, in accordance with the assessment speciﬁcation recognized in the industrial sector

concerned. Service operations should only be carried out in accordance with the recommendations of the

equipment manufacturer. Maintenance and repair operations that require the assistance of other qualiﬁed

persons must be conducted under the supervision of the person competent for the use of ﬂammable

refrigerants.

14. Every working procedure that affects safety means shall only be carried out by competent persons.

15. Warning:

• Do not use means to accelerate the defrosting process or to clean, other than those recommended by the

manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources (for example: open

ﬂames, an operating gas appliance or an operating electric heater.

• Do not pierce or burn.

• Be aware that refrigerants may not contain an odour.

Caution: Risk of ﬁre Operating instructions Read technical manual

16. Information on servicing:

1. Checks to the area

Prior to beginning work on systems containing ﬂammable refrigerants, safety checks are necessary to ensure

that the risk of ignition is minimized. For repair to the refrigerating system, the following precautions shall be

complied with prior to conducting work on the system.

2. Work procedure

Work shall be undertaken under a controlled procedure so as to minimize the risk of a ﬂammable gas or

vapour being present while the work is being performed.

3. General work area

All maintenance staff and others working in the local area shall be instructed on the nature of work being

carried out. Work in conﬁned spaces shall be avoided. The area around the workspace shall be sectioned off.

Ensure that the conditions within the area have been made safe by control of ﬂammable material.

4. Checking for presence of refrigerant

The area shall be checked with an appropriate refrigerant detector prior to and during work, to ensure the

technician is aware of potentially ﬂammable atmospheres. Ensure that the leak detection equipment being

used is suitable for use with ﬂammable refrigerants, i.e. non-sparking, adequately sealed or intrinsically safe

5. Presence of ﬁre extinguisher

If any hot work is to be conducted on the refrigeration equipment or any associated parts, appropriate ﬁre

13

ENG

extinguishing equipment shall be available to hand. Have a dry powder or CO2 ﬁre extinguisher adjacent to

the charging area.

6. No ignition sources

No person carrying out work in relation to a refrigeration system which involves exposing any pipe work shall

use any sources of ignition in such a manner that it may lead to the risk of ﬁre or explosion. All possible ignition

sources, including cigarette smoking, should be kept sufﬁciently far away from the site of installation, repairing,

removing and disposal, during which refrigerant can possibly be released to the surrounding space. Prior to

work taking place, the area around the equipment is to be surveyed to make sure that there are no ﬂammable

hazards or ignition risks. “No Smoking” signs shall be displayed.

7. Ventilated area

Ensure that the area is in the open or that it is adequately ventilated before breaking into the system or

conducting any hot work. A degree of ventilation shall continue during the period that the work is carried

out. The ventilation should safely disperse any released refrigerant and preferably expel it externally into the

atmosphere.

8. Checks to the refrigeration equipment

Where electrical components are being changed, they shall be ﬁt for the purpose and to the correct

speciﬁcation. At all times the manufacturer’s maintenance and service guidelines shall be followed. If in doubt

consult the manufacturer’s technical department for assistance.

The following checks shall be applied to installations using ﬂammable refrigerants:

- The charge size is in accordance with the room size within which the refrigerant containing parts are installed;

- The ventilation machinery and outlets are operating adequately and are not obstructed;

- If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence of

refrigerant;

- Marking to the equipment continues to be visible and legible. Markings and signs that are illegible shall be

corrected;

- Refrigeration pipe or components are installed in a position where they are unlikely to be exposed to any

substance which may corrode refrigerant containing components, unless the components are constructed of

materials which are inherently resistant to being corroded or are suitably protected against being so corroded.

9. Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks and component inspection

procedures. If a fault exists that could compromise safety, then no electrical supply shall be connected to

the circuit until it is satisfactorily dealt with. If the fault cannot be corrected immediately but it is necessary to

continue operation, an adequate temporary solution shall be used. This shall be reported to the owner of the

equipment so all parties are advised.

Initial safety checks shall include:

-That capacitors are discharged: this shall be done in a safe manner to avoid possibility of sparking;

-That there no live electrical components and wiring are exposed while charging, recovering or purging the

system;

-That there is continuity of earth bonding.

17. Repairs to sealed components

1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment

being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an electrical

supply to equipment during servicing, then a permanently operating form of leak detection shall be located at

the most critical point to warn of a potentially hazardous situation.

2. Particular attention shall be paid to the following to ensure that by working on electrical components, the

casing is not altered in such a way that the level of protection is affected. This shall include damage to cables,

excessive number of connections, terminals not made to original speciﬁcation, damage to seals, incorrect

ﬁtting of glands, etc.

Ensure that apparatus is mounted securely.

Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of

preventing the ingress of ﬂammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s speciﬁcations.

NOTE: The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment.

Intrinsically safe components do not have to be isolated prior to working on them.

18. Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this will not

exceed the permissible voltage and current permitted for the equipment in use.

Intrinsically safe components are the only types that can be worked on while live in the presence of a

ﬂammable atmosphere. The test apparatus shall be at the correct rating.

14

ENG

Replace components only with parts speciﬁed by the manufacturer. Other parts may result in the ignition of

refrigerant in the atmosphere from a leak.

19. Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any

other adverse environmental effects. The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

20. Detection of ﬂammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks. Ahalide torch (or any other detector using a naked ﬂame) shall not be used.

21. Leak detection methods

The following leak detection methods are deemed acceptable for systems containing ﬂammable refrigerants.

Electronic leak detectors shall be used to detect ﬂammable refrigerants, but the sensitivity may not be

adequate, or may need re-calibration. (Detection equipment shall be calibrated in a refrigerant-free area.)

Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used. Leak

detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be calibrated to the

refrigerant employed and the appropriate percentage of gas (25 % maximum) is conﬁrmed.

Leak detection ﬂuids are suitable for use with most refrigerants but the use of detergents containing chlorine

shall be avoided as the chlorine may react with the refrigerant and corrode the copper pipe-work.

If a leak is suspected, all naked ﬂames shall be removed/ extinguished.

If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered from the

system, or isolated (by means of shut off valves) in a part of the system remote from the leak. Oxygen free

nitrogen (OFN) shall then be purged through the system both before and during the brazing process.

22. Removal and evacuation

When breaking into the refrigerant circuit to make repairs or for any other purpose conventional procedures

shall be used. However, it is important that best practice is followed since ﬂammability is a consideration. The

following procedure shall be adhered to:

- Remove refrigerant;

- Purge the circuit with inert gas;

- Evacuate;

- Purge again with inert gas;

-Open the circuit by cutting or brazing.

The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be ﬂushed

with OFN to render the unit safe. This process may need to be repeated several times. Compressed air or

oxygen shall not be used for this task.

Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to ﬁll until the

working pressure is achieved, then venting to atmosphere, and ﬁnally pulling down to a vacuum. This process

shall be repeated until no refrigerant is within the system. When the ﬁnal OFN charge is used, the system shall

be vented down to atmospheric pressure to enable work to take place. This operation is absolutely vital if

brazing operations on the pipe-work are to take place.

Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

23. Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the equipment

and all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior to the task

being carried out, an oil and refrigerant sample shall be taken in case analysis is required prior to re-use of

reclaimed refrigerant. It is essential that electrical power is available before the task is commenced.

a. Become familiar with the equipment and its operation.

b. Isolate system electrically.

c. Before attempting the procedure, ensure that:

- mechanical handling equipment is available, if required, for handling refrigerant cylinders;

- all personal protective equipment is available and being used correctly;

- the recovery process is supervised at all times by a competent person;

- recovery equipment and cylinders conform to the appropriate standards.

d. Pump down refrigerant system, if possible.

e. If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of the

system.

f. Make sure that cylinder is situated on the scales before recovery takes place.

g. Start the recovery machine and operate in accordance with manufacturer’s instructions.

h. Do not overﬁll cylinders. (No more than 80 % volume liquid charge).

i. Do not exceed the maximum working pressure of the cylinder, even temporarily.

15

ENG

j. When the cylinders have been ﬁlled correctly and the process completed, make sure that the cylinders and

the equipment are removed from site promptly and all isolation valves onthe equipment are closed off.

k. Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned and

checked.

24. Labelling

Equipment shall be labelled stating that it has been de-commissioned and emptied of refrigerant. The label

shall be dated and signed. Ensure that there are labels on the equipment stating the equipment contains

ﬂammable refrigerant.

25. Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended good

practice that all refrigerants are removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovery cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge are available. All

cylinders to be used are designated for the recovered refrigerant and labelled for that refrigerant (i.e. special

cylinders for the recovery of refrigerant). Cylinders shall be complete with pressure-relief valve and associated

shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible, cooled before

recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment

that is at hand and shall be suitable for the recovery of all appropriate refrigerants including, when applicable,

ﬂammable refrigerants. In addition, a set of calibrated weighing scales shall be available and in good working

order. Hoses shall be complete with leak-free disconnect couplings and in good condition. Before using the

recovery machine, check that it is in satisfactory working order, has been properly maintained and that any

associated electrical components are sealed to prevent ignition in the event of a refrigerant release. Consult

manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recover cylinder, and the

relevant waste transfer note arranged. Do not mix refrigerants in recovery units and especially not in cylinders.

If compressors or compressor oils are to be removed, ensure that they have been evacuated to an acceptable

level to make certain that ﬂammable refrigerant does not remain within the lubricant. The evacuation process

shall be carried out prior to returning the compressor to the suppliers. Only electric heating to the compressor

body shall be employed to accelerate this process. When oil is drained from a system, it shall be carried out

safely.

ENG

INSTALLATION PRECAUTIONS (R32)

Important considerations

1. The air conditioner you buy must be installed by professional personnel and the Installation manual is used

only for the professional installation personnel! The installation speciﬁcations should be subject to our after-

sale service regulations.

2. When ﬁlling the combustible refrigerant, any of your rude operations may cause serious injury or injuries to

human body or bodies and object or objects.

3. A leak test must be done after the installation is completed.

4. It is a must to do the safety inspection before maintaining or repairing an air conditioner using combustible

refrigerant in order to ensure that the ﬁre risk is reduced to minimum.

5. It is necessary to operate the machine under a controlled procedure in order to ensure that any risk arising

from the combustible gas or vapor during the operation is reduced to minimum.

6. Requirements for the total weight of ﬁlled refrigerant and the area of a room to be equipped with an air

conditioner (are shown as in the following Tables GG.1 and GG.2)

The maximum charge and the required minimum ﬂoor area

m1 = (4 m3) x LFL , m2 = (26 m3) x LFL, m3 = (130 m3 ) x LFL

Where LFL is the lower ﬂammable limit in kg/m3, R32 LFL is 0.038 kg/m3.

For the appliances with a charge amount m1 < M = m2:

The maximum charge in a room shall be in accordance with the following:

mmax = 2.5 x (LFL)(5/4) x h0 x (A)1/2

The required minimum ﬂoor area Amin to install an appliance with refrigerant charge M (kg) shall be in accordance

with following: Amin = (M/ (2.5 x (LFL)(5/4) x h0))2

Where:

Category LFL

(kg/m3)h0 (m) Floor area (m2)

4 7 10 15 20 30 50

R32 0.306

11.14 1.51 1.8 2.2 2.54 3.12 4.02

1.8 2.05 2.71 3.24 3.97 4.58 5.61 7.254

2.2 2.5 3.31 3.96 4.85 5.6 6.86 8.85

Table GG.1 - Maximum charge (kg)

Category LFL

(kg/m3)h0 (m) Charge amount (M) (kg) Minimum room area (m2)

4 7 10 15 20 30 50

R32 0.306

1.224kg 1.836kg 2.448kg 3.672kg 4.896kg 6.12kg 7.956kg

0.6 29 51 116 206 321 543

110 19 42 74 116 196

1.8 3 6 13 23 36 60

2.2 24915 24 40

Table GG.2 - Minimum room area (m2)

17

ENG

Installation Safety Principles

1. Site Safety

2. Operation Safety

3. Installation Safety

• Open Flames Prohibited

• Ventilation Necessary

• Mind Static Electricity

• Must wear protective clothing and anti-static gloves

• Don`t use mobile phone

• Refrigerant Leak Detector

• Appropriate Installation Location

Please note that:

1. The installation site should be well-ventilated.

2. The sites for installing and maintaining an air conditioner using Refrigerant R32 should be free from open ﬁre

or welding, smoking, drying oven or any other heat source higher than 548 which easily produces open ﬁre.

3. When installing an air conditioner, it is necessary to take appropriate anti-static measures such as wear anti-

static clothing and/or gloves.

4. It is necessary to choose the site convenient for installation or maintenance wherein the air inlets and outlets

of the indoor and outdoor units should be not surrounded by obstacles or close to any heat source or

combustible and/or explosive environment.

5. If the indoor unit suffers refrigerant leak during the installation, it is necessary to immediately turn off the valve

of the outdoor unit and all the personnel should go out till the refrigerant leaks completely for 15 minutes. If

the product is damaged, it is a must to carry such damaged product back to the maintenance station and it is

prohibited to weld the refrigerant pipe or conduct other operations on the user’s site.

6. It is necessary to choose the place where the inlet and outlet air of the indoor unit is even.

7. It is necessary to avoid the places where there are other electrical products, power switch plugs and sockets,

kitchen cabinet, bed, sofa and other valuables right under the lines on two sides of the indoor unit.

The left picture is the schematic diagram

of a refrigerant leak detector.

18

ENG

Suggested Tools

Tool Picture Tool Picture Tool Picture

Standard

Wrench Pipe Cutter Vacuum Pump

Adjustable/

Crescent

Wrench

Screw drivers

(Phillips & Flat

blade)

Safety Glasses

Torque Wrench Manifold and

Gauges Work Gloves

Hex Keys or

Allen Wrenches Level Refrigerant

Scale

Drill & Drill Bits Flaring tool Micron Gauge

Hole Saw Clamp on Amp

Meter

Inverter Models Capacity (Btu/h) 9K-12K 18K-36K

Lenght of pipe with standard charge 5m 5m 5m 5m

Lenght of pipe with standard charge (Like: North

American, etc.) 7.5m 7.5m 7.5m 7.5m

Maximum distance between indoor and outdoor unit 15m 25m 25m 25m

Additional refrigerant charge 20g/m 15g/m 30g/m 25g/m

Max. diff. in level between indoor and outdoor unit 10m 10m 10m 10m

Type of refrigerant R22/R410A R32 R22/R410A R32

Pipe Length and Additional Refrigerant

PIPE Newton meter [N x m] Pound-force foot (1bf-ft) Kilogram-force meter

(kgf-m)

1/4" (ɸ6) 18 - 20 24.4 - 27.1 2.4 - 2.7

3/8” (ɸ9.52) 30 - 35 40.6 - 47.4 4.1 - 4.8

1/2” (ɸ12) 45 - 50 61.0 - 67.7 6.2 - 6.9

5/8” (ɸ15.88) 60 - 65 81.3 - 88.1 8.2 - 8.9

Torque Parameters

19

ENG

This table is only for reference, the installation shall meet the requirements of local laws

and regulations.

NOTE

Maximum Operating

Current of Air

Conditioner (A)

Minimum Wire Cross-

sectional Area (mm2)

Speciﬁcation of Socket

or Switch (A) Fuse Speciﬁcation (A)

≤ 8 0.75 10 20

> 8 and ≤10 1.0 10 20

> 10 and ≤15 1.5 16 32

> 15 and ≤24 2.5 25 32

> 24 and ≤28 4.0 32 64

> 28 and ≤32 6.0 40 64

Dedicated Distribution Device and Wire for Air Conditioner

Step1: Select Installation location

1. Ensure the installation complies with the installation minimum dimensions (deﬁned below) and meets the

minimum and maximum connecting piping length and maximum change in elevation as deﬁned in the

System Requirements section.

2. Air inlet and outlet will be clear of obstructions, ensuring proper airﬂow throughout the room.

3. Condensate can be easily and safely drained.

4. All connections can be easily made to outdoor unit.

5. Indoor unit is out of reach of children.

6. A mounting wall strong enough to withstand four times the full weight and vibration of the unit.

7. Filter can be easily accessed for cleaning.

8. Leave enough free space to allow access for routine maintenance.

9. Install at least 10 ft. (3 m) away from the antenna of TV set or radio. Operation of the air conditioner may

interfere with radio or TV reception in areas where reception is weak. An ampliﬁer may be required for the

affected device.

10. Do not install in a laundry room or by a swimming pool due to the corrosive environment.

INDOOR UNIT INSTALLATION

20

ENG

NOTE:

(I) Make sure the mounting plate is ﬁrm enough and ﬂat against the wall after installation.

(II) This ﬁgure shown may be different from the actual object, please take the latter as the standard.

Step2: Install Mounting Plate

Minimum Indoor Clearances

1. Take the mounting plate from the back of indoor unit.

2. Ensure to meet the minimum installation dimension requirements as step 1, according to the size of mounting

plate, determine the position and stick the mounting plate close to the wall.

3. Adjust the mounting plate to a horizontal state with a spirit level, then mark out the screw hole positions on the

wall.

4. Put down the mounting plate and drill holes in the marked positions with drill.

5. Insert expansion rubber plugs into the holes, then hang the mounting plate and ﬁx it with screws.

Ceiling

Floor

Reference screw positions

Spirit level

Mounting plate

Pagina se încarcă...

Tesla TM36AF21-1232IA Split-type Air Conditioning Manual de utilizare

Tesla TM36AF21-1232IA Split-type Air Conditioning Manual de utilizare

Lucrări înrudite

Alte documente