Phcbi MPR-S500H Instrucțiuni de utilizare

Please read the operating instructions carefully before using this product, and keep the operating

instructions for future use.

See page 63 for all model numbers.

Operating Instructions

Pharmaceutical Refrigerator

MPR-S500H

2

CONTENTS

INTRODUCTION ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ4

PRECAUTIONS FOR SAFE OPERATION ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ5

ENVIRONMENTAL CONDITIONS ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 10

SYMBOLS ON UNIT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 11

REFRIGERATOR COMPONENTS

Main body ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 12

Control panel ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 14

INSTALLATION SITE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 15

INSTALLATION ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 16

PLACEMENT OF STORED ITEMS ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 18

USE OF SHELVES AND DRAWERS ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 19

START-UP PROCEDURE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 20

AFTER RECOVERY FROM POWER FAILURE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 20

HOME SCREEN (Temperature display screen) ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 21

MENU SCREEN ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 22

SETTING THE CHAMBER TEMPERATURE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 24

SETTING THE KEYPAD LOCK ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 25

RELEASING THE KEYPAD LOCK ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 26

DISPLAY OF MAX/MIN TEMPERATURE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 27

RESET OF MAX/MIN TEMPERATURE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 28

SETTING THE PERIOD FOR MAX/MIN TEMPERATURE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 29

DISPLAY AND EXPORT OF DATA LOG

Display & export of temp. and door operation logs ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 30

Export of temperature and door operation logs ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 32

Setting the log interval ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 33

Setting the device ID ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 34

DISPLAY OF ALARM LOG ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 35

EXPORT OF ALARM LOG ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 36

SETTING THE SELECTABLE PARAMETERS

Selectable parameters

ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 37

Setting the temperature display ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 38

Setting the high-temperature alarm ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 39

Setting the low-temperature alarm ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 40

Setting the door buzzer delay ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 41

Setting the buzzer suspended period ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 42

Setting the buzzer volume ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 43

Setting the remote alarm ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 44

Setting the interior light ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 45

Setting the lighting time ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 46

Setting the compressor delay ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 47

3

CONTENTS

Setting the date display (format) ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 48

Setting the date ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 49

Setting the time ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 50

REMOTE ALARM TERMINAL ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 51

ALARMS AND SELF-DIAGNOSIS ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 52

ROUTINE MAINTENANCE

Cleaning of exterior, interior, door rail (including drain port) and accessories ꞏꞏꞏꞏꞏꞏ 53

DEFROSTING ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 53

TROUBLESHOOTING ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 54

DISPOSAL OF UNIT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 56

Decontamination of unit ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 56

TEMPERATURE RECORDER (OPTION) ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 61

BATTERY KIT FOR POWER FAILURE ALARM (OPTION) ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 61

LIGHT SHIELDING PLATE, SHADING MEDICINE BOX (OPTION) ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 61

SPECIFICATIONS ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 62

PERFORMANCE ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 63

SAFETY CHECK SHEETꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 64

4

INTRODUCTION

Read the operating instructions carefully before using the appliance and follow the instructions for safe

operation.

Handling of Operating Instructions

 PHC Corporation never guarantees any safety if the appliance is used for any objects other than

intended use or used by any procedures other than those mentioned in the operating instructions.

 Keep the operating instructions in an adequate place to refer to it as necessary.

 Contact our sales representative or agent if any page of the operating instructions is lost or page order

is incorrect.

 Contact our sales representative or agent if any point in the operating instructions is unclear or if there

are any inaccuracies.

The operating instructions is only for the pharmaceutical refrigerator MPR-S500H and MPR-S500RH made by PHC

Corporation.

The contents are subject to change without notice.

No part of the operating instructions may be reproduced in any form without the expressed written permission of

PHC Corporation.

Proposal for safe storage of refrigerator contents

We can offer some precautions below to protect the valuable material against accidental temperature rise.

Contact our sales representative or agent for the details or installation.

▪ Temperature recorder (Option)

▪ Battery kit for power failure alarm (Option)

▪ Remote alarm system (Marketed product)

IMPORTANT NOTICE

PHC Corporation guarantees this product under certain warranty conditions. However, please note that

PHC Corporation shall not be responsible for any loss or damage to the contents of the product.

This equipment is designed for storage of pharmaceuticals, samples and reagents.

5

PRECAUTIONS FOR SAFE OPERATION

It is imperative that the user complies with the operating instructions

as they contain important safety advice.

Items and procedures are described so that you can use this unit correctly and safely.

Following these precautions will prevent possible injury to the user and any other

person.

Precautions are illustrated in the following way:

WARNING

Warning indicates a potentially hazardous situation which, if not avoided,

could result in serious injury or death.

CAUTION

Failure to observe CAUTION signs could result in injury to personnel and

damage to the unit and associated property.

Symbols have the following meanings:

This symbol means caution.

This symbol means an action is prohibited.

This symbol means an instruction must be followed.

Be sure to keep the operating instructions in a place that is accessible to users of this

unit.

6

PRECAUTIONS FOR SAFE OPERATION

Never damage the power supply cord or power supply plug (by breaking, adapting, placing

near a source of heat, bending with force, twisting, pulling, adding weight, or binding). A

damaged power supply cord or power supply plug may cause electric shock, short circuit, or fire.

Remove dust from the power supply plug periodically. Dust on the power supply plug may cause

insulation failure due to moisture and thus cause a fire. Disconnect the power supply plug and wipe it

with a dry cloth.

Make sure the power supply plug is pushed fully in. Faulty insertion of the power supply plug may

cause electric shock or fire due to generation of heat. Never use a damaged power supply plug or

loose power outlet.

Do not touch any electrical parts (such as power supply plug) or operate switches with a wet

hand. This may cause electric shock.

Use a dedicated power source as indicated on the rating label attached to the unit. A

multiple-tap may cause fire resulting from abnormal heating.

Do not use the unit outdoors. Exposure to rain may cause leakage and/or electric shock.

Only qualified engineers or service personnel should install the unit. Installation by unqualified

personnel may cause water leakage, electric shock, or fire.

Install the unit in a location capable of bearing the total combined weight (product + optional

accessories + stored items). After installing the unit, be absolutely sure to take precautions to

prevent the unit from falling over. If the unit is installed in a location which is not strong enough or if

the proper precautions are not taken, the unit may fall over and cause injuries.

Do not install the unit in a location where flammable or volatile substances are present.

Installing the unit in a location where flammable or volatile substances are present may cause

explosions and/or a fire.

Do not install the unit where there are high levels of moisture or where it may be splashed with

water. Installing the unit where there are high levels of moisture or where it may be splashed with

water may cause the insulation to deteriorate and give rise to leakage and/or electric shock.

Be absolutely sure to earth (gound) the unit in order to prevent electric shock. Failure to earth

the product may give rise to electric shock. If necessary, ask a qualified contractor to do this work.

Do not connect the earth wire to a gas pipe, water pipe, or lightning rod when earthing

the unit. Earthing the unit improperly may give rise to electric shock.

WARNING

7

PRECAUTIONS FOR SAFE OPERATION

Never store volatile or flammable substances in this unit except in a sealed container. Such

substances may cause explosion or fire if they leak.

Never insert metal objects such as pins and wires into any vent, gap, or outlet on the unit.

This may cause electric shock or injury by accidental contact with moving parts.

When handling harmful samples (for example, those which consist of toxic, pathogenic, or

radioactive substances), install the unit inside a designated isolation facility. If the unit is

installed in a location which is not an isolation facility, there may be detrimental effects on both people

and the natural environment.

Before proceeding with maintenance or checking of the unit, disconnect the power supply plug.

Performing the work while power is still flowing to the product or while the power supply plug is still

connected may give rise to electric shock and/or injury.

Wear protective gloves and mask during maintenance. Touching or inhaling chemicals or aerosols

from around the unit may be detrimental to health.

Never splash water directly onto the unit as this may cause electric shock or short circuit.

Never put containers with liquid on top of the unit as this may cause electric shock or short circuit

if the liquid is spilled.

Never disassemble, repair, or modify the unit yourself. A high-voltage area is located inside the

unit. Any work carried out by unauthorized personnel may result in electric shock. Contact our sales

representative or agent for maintenance or repair.

Disconnect the power supply plug if there is anything wrong with the unit. Continued abnormal

operation may cause electric shock or fire.

Grip the power supply plug when disconnecting the power supply cord from the outlet.

Pulling the power supply cord may cause electric shock or short circuit.

Disconnect the power supply cord when the unit is not in use for long periods. Keeping the unit

connected may cause electric shock, leakage, or fire due to the deterioration of insulation.

Do not place this unit in a location where it is difficult to disconnect the power supply plug.

Failure to disconnect the power supply plug may cause fire in the event of a problem or malfunction.

If the unit is to be stored unused in an unsupervised area for a long period, ensure that children do

not have access and that doors cannot be closed completely.

WARNING

8

PRECAUTIONS FOR SAFE OPERATION

Ask a qualified contractor to carry out disassembly and disposal of the unit. Leaving the unit in

a location that can be accessed by third parties may result in unexpected accidents (e.g. the unit may

be used for unintended purposes).

Do not leave the plastic bags used for packing in a place where they can be reached by small

children as this may result in unexpected accidents such as suffocation.

When moving the unit, be sure to take precautions to prevent it from falling over. Moving the

unit with too much force may cause it to fall over, possibly resulting in injury. A qualified individual

must be assigned to supervise the safe movement and relocation of the unit.

Do not install the unit in a location where corrosive gases such as acids are present. Installing

the unit in a location where corrosive substances are present may cause electric components to

corrode, leading to leakage and/or electric shock due to the deterioration of insulation resulting from

corroded electrical components.

Connect the unit to a power source as indicated on the rating label attached to the unit. Use of

any other voltage or frequency other than that on the rating label may cause fire or electric shock.

Never damage the chamber wall or pipework in the chamber when removing frost. The

refrigerant is flammable and may cause a fire if it leaks.

Install the unit in a well-ventilated (airy) location to prevent the accumulation of flammable

refrigerant. The flammable refrigerant may cause fire if it leaks.

Flammable and explosive product. The unit contains flammable refrigerant. When repairing or

recycling, only trained service personnel will repair and follow the procedure below.

 Well ventilate the room to prevent refrigerant accumulation.

 Keep fire away when the refrigerant is contained in the product.

 Do not damage or break the pipework.

Stop using the fire, open the windows for ventilation, and leave the unit as it is if the pipework

is damaged or the leakage of flammable refrigerant is noticed. Then contact our sales

representative or agent. Disconnection or connection of the power supply plug may cause ignition,

explosion, or fire.

Always use the power supply cord that is provided. Other power supply cord may cause electric

shock or fire.

Do not use the provided power supply cord for other equipment. That may cause electric shock

or fire.

WARNING

9

PRECAUTIONS FOR SAFE OPERATION

This unit must be plugged into a dedicated circuit protected by branch circuit breaker.

Use a dedicated power source as indicated on the rating label attached to the unit. A

multiple-tap may cause fire resulting from abnormal heating.

Do not climb on top of the unit or put any objects on the unit. Falling from the unit may cause

injury; falling objects may cause damage to the unit.

Never install the unit in a location where corrosive materials such as sulphur compounds are

likely to be generated (e.g. near a drainage facility). Corrosion of the copper pipes may result in the

deterioration and consequently the failure of the cooling unit.

Before resuming operation after the unit has been turned off, be absolutely sure to check the

settings. Items stored inside the unit may be adversely affected if operation of the unit is resumed

with changed settings.

Never store corrosive substances such as acids or alkalis in the unit except in a sealed

container. These may be detrimental to health and may cause corrosion of internal components,

cooling circuit or electrical components.

To ensure the safety of the service engineer, submit a safety check sheet with the required

items filled out. This is provided as the photocopiable “Safety Check Sheet” at the end of these

operating instructions.

Use designated parts for parts replacement. Using an incorrect part may cause fire.

Do not give strong shock or vibration during movement or use. The piping may be damaged,

causing a fire.

Flammable and explosive product. The unit contains flammable refrigerant. Consult repair

manual/owner’s guide before attempting to install or service this product. All safety precautions must

be followed.

Flammable refrigerant used. Flammable and explosive product. Dispose of properly in

accordance with national regulations.

Take care not to fall down the glass door when removing. Improper handling may cause damage

of glass door or injury.

Be careful not to pinch your fingers in the slide rail or the lock mechanism of the drawer. It may

cause injury.

CAUTION

10

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions (based on the IEC 61010-1):

 Indoor use;

 Altitude up to 2000 m;

 Temperature 5 oC to 40 oC;

 Maximum relative humidity 80 % for temperature up to 31 oC decreasing linearly to 50 % relative

humidity at 40 oC;

 Mains supply voltage fluctuations up to ±10 % of the nominal voltage;

 Transient overvoltages up to the levels of OVERVOLTAGE CATEGORY II;

 Temporary OVERVOLTAGES occurring on the mains supply;

 Applicable pollution degree of the intended environment (POLLUTION DEGREE 2 in most cases);

The above is not a performance specification. Refer to “PERFORMANCE” page for the performance

specifications and the environmental conditions.

11

SYMBOLS ON UNIT

The following symbols are attached to the unit. The table describes the meaning of the symbols.

This symbol is attached to covers that access high-voltage electrical components to

prevent electric shock. Only a qualified engineer or service personnel should be

allowed to open these covers.

This symbol indicates that caution is required. Refer to product documentation for

details.

This symbol indicates incorrect usage could lead to a fire hazard.

This symbol indicates an earth.

This symbol means “ON” for a power switch.

This symbol means “OFF” for a power switch.

12

REFRIGERATOR COMPONENTS

Main body

Back side

MPR-S500RH

Interior

light

13

REFRIGERATOR COMPONENTS

Control panel: The chamber temperature and other alarms/functions can be set using the keys on

the control panel. The operational status can be checked on the temperature display and indicator [page

14].

Door switch: This switch detects the door open/close status. The LED lamp on the control panel

blinks red when the door is open.

Air intake vent: This is an air intake vent for circulating the air in the chamber. Do not block this vent.

Blocking this vent may cause unstable chamber temperature.

Glass door: Sliding type. The recessed portion on the rail enables the self-closing of the door. The

glass is pair construction.

The condensation may be found on the door frame and on the glass surface depending on the installation

environment. This is not a malfunction. This is not unusual.

The condensation on the door is dropped on the rail and exhausted to the evaporating tray.

Drawer (right side of MPR-S500RH): The allowable load is 20 kg per drawer [page 19].

Note: Never pull out the multiple drawers at a time. It may cause tipping over of the unit.

Space for temperature recorder: A temperature recorder (optional) can be mounted here so that the

chamber temperature can be recorded automatically [page 61].

Contact our sales representative or agent to arrange the installation.

Leveling foot (front): These are screw bolts used to install and fix the unit. Adjust the height of the

levelling feet by turning the screw bolts until the two front casters are away from the floor [page 16].

Keyhole: Push and turn the key clockwise through 90 degree to securely lock the door.

Shelf: The location is selectable. Set the shelves horizontally and securely. The allowable load is 20

kg (MPR-S500RH) and 50 kg (MPR-S500H) per shelf.

Items to be stored in the chamber must be placed on the shelves. Do not put stored items directly on the bottom of

the chamber.

Access port: This port is used to pass the sensor or cable of measuring equipment, or the sensor of

a temperature recorder (optional) to the chamber.

Replace the insulation and the rubber caps when the access port is not in use. Improper replacement may cause

an increase in chamber temperature or condensation around the access port.

Air exhaust vent: This is an air exhaust vent for circulating the air in the chamber. Do not block this

vent.

Blocking this vent may cause unstable chamber temperature.

Remote alarm terminal (backside): A remote alarm device (separately available) can be connected

to this terminal. The remote alarm relays the alarm to an operator in a remote location if the unit is un

attended [page 51].

Contact our sales representative or agent to arrange the installation

Circuit breaker (backside): Before starting the refrigerator, check the switch is on.（ON=“｜”，

OFF=“○”）

The round button under the circuit breaker is a leakage test button. The operation check of the circuit breaker can

be performed by pressing this button. But note the power supply to the unit is disconnected when this button is

pressed.

Space for interface board: An interface board (optional) can be mounted here [page 61].

Contact our sales representative or agent to arrange the installation.

Port for servicing (back, left): This is a access port for servicing. Do not remove the rubber cap.

Switch for power failure alarm: This is a switch for power failure alarm [page 61]. Normally, set the

switch to ON. Turn off the switch when the refrigerator is no use.

This switch is provided with the optional battery kit for power failure alarm.

14

REFRIGERATOR COMPONENTS

Control panel

LED indicator: In normal operation, the green LED lamp lights up, and during alarm condition, the red

LED lamp blinks to indicate alarm. The orange LED lamp lights up during standby status.

Temperature display: The present chamber temperature, log chart, or input screen, etc. are

displayed.

Up/down/left/right key (△▽ ):

On the screen “other than the home screen”: pressing this key moves the cursor, etc.

Menu key (MENU/HOME):

On the “home screen (temperature display screen)”: pressing this key leads the menu screen. It is

possible to set various setting on the menu screen.

On the ”other than the home screen”: pressing this key leads the home screen.

Cancel key (CANCEL): On the setting screen, pressing this key changes into the screen of one level

up.

Standby key: The normal status and standby status is changed by pressing this key for three

seconds. The operation stops during standby. Pressing this key for three seconds during normal

operation displays “Waiting” until the compressor stops. After a few minutes (up to 5 minutes) the display

disappears and the orange LED lamp lights up. Pressing this key for three seconds during standby status

appears the home screen (temperature display) and lights up the green LED lamp.

Buzzer stop key (BUZZER STOP): The buzzer is silenced by pressing this key when the buzzer

sounds [page 52].

The alarm status of remote alarm terminal is not cancelled by pressing the buzzer stop key (BUZZER STOP) since

the remote alarm is not linked with buzzer (The buzzer is silenced). Refer to “Setting the remote alarm” on page 44 to

link the remote alarm with the buzzer.

The buzzer and the remote alarm operate again after certain period (buzzer suspended period) when the same

alarm status is continued [page 42].

The chamber temperature is displayed for five seconds by pressing this key during power failure alarm

(when MPR-48B2 is installed).

Light key (LIGHT): The light turns on by pressing this key when the light is off. The light turns off by

pressing this key when the light is on.

This key is invalid when the setting of interior light is ON or OFF.

Enter key (ENTER): Press this to select the menu item. Press this key to enter the required value

during the setting procedure.

USB port (under side): Insert a USB flash drive to export data logs.

USB flash drives with capacity of 32 GB or less that employ the FAT16/FAT32 file system are supported. USB flash

drives that require passwords cannot be used. Do not insert devices other than USB flash drives into the USB port.

15

INSTALLATION SITE

This unit must be installed in a location which meets all the conditions described below.

 If the unit is installed in a location which does not meet the conditions, its specified performance may not be

achieved or malfunctions and accidents may occur.

■ A location not exposed to direct sunlight

Avoid any location which is exposed to direct sunlight. Installing the unit in a location exposed to direct

sunlight may reduce its cooling performance.

■ A well-ventilated (airy) location

In order to ensure ventilation, leave clearances of at least 10 cm around the unit (at the left, right, top and

back). Blocking the ventilation may reduce the unit’s cooling performance or cause malfunctions.

■ A location away from sources of heat

Avoid any location which is close to a major source of heat (such as a heater or boiler). Installing the unit

near a major source of heat may reduce the unit’s cooling performance.

■ A location with minimal changes in temperature

Avoid any location where the ambient temperature is subject to sudden changes. If the unit is installed in

a location where the ambient temperature is subject to sudden changes, it will not be possible to achieve

a stable cooling performance.

■ A flat surface where the floor is also capable of bearing the total combined weight (product +

optional accessories + stored items)

Install the unit on a flat surface which is even and which is capable of bearing the total combined weight

(product + optional accessories + stored items). If the unit is installed where the surface is uneven or

where the unit will be inclined at an angle, the unit will be unstable, and accidents or injuries may occur

and/or vibration or unnecessary noise may be generated.

■ A location with minimal humidity

Install the unit in a location where the relative humidity is less than 80 %R.H. Installing the unit in a very

humid location may cause earth faults and/or electric shock. If installed at a humidity of 80% or higher,

condensation may form on the unit.

■ A location free of flammable or corrosive gases

Avoid any location exposed to flammable or corrosive gases. Flammable or corrosive gases can cause

explosions and/or a fire. Furthermore, corrosion of electrical parts may cause insulation to be reduced

and result in earth faults and/or electric shock.

■ A location where nothing can fall onto the unit

Avoid locations where objects may fall onto the unit. Objects falling and hitting the unit may cause it to

break down or fail.

16

INSTALLATION

1. Preparations after unpacking

Remove all the tape used to secure the doors and interior parts, and leave the doors open for a short

while for ventilation.

If any surfaces of the outer cabinet are dirty, wipe the surface using a cloth moistened with a diluted

neutral dish-washing detergent.

Using an undiluted solution of detergent may cause the unit’s plastic areas to crack. Follow the directions on the

detergent for details of dilution.

After wiping the unit using the diluted detergent, be absolutely sure to wipe the surfaces with a cloth dipped in clean

water to remove traces of the detergent. After this, be absolutely sure to wipe the surfaces with a dry cloth, allowing

the surfaces of the outer cabinet to dry out completely, and then proceed with the installation.

2. Securing and levelling the unit using the levelling

feet

Rotate the front levelling feet until the casters are raised

above the floor surface [Fig. 1].

In addition, rotate the levelling feet slightly clockwise or

anticlockwise, and adjust them so that the unit is

completely level.

When the casters are raised from the floor surface, the unit will

be secured. If they are left touching the floor, the unit may

accidently move when its door is opened or closed.

3. Securing the unit by using the fixtures

Use the fixtures on the rear panel of the unit, and secure

the unit to a wall with a strong rope or chain [Fig. 2].

4. Preventing electric shock by earthing the unit

When installing the unit, be absolutely sure to earth

(ground) it. Earthing is necessary to prevent electric

shocks resulting from deterioration of electrical insulations.

This unit comes with a 3-pin plug having one earth pin.

Earthing is not required in the case of a 3-pin power outlet

equipped with an earth contact.

If the power outlet is not a 3-pin outlet equipped with an earth

contact, ask a qualified contractor to do the earthing work.

Fig. 1

Leveling foot

Fixture

Fig. 2

Shrink

Stretch

17

INSTALLATION

5. Setting up the shelves

The shelves are packaged at the bottom of the chamber.

Set the shelves firmly in place on the shelf stoppers at the

standard locations with marking [Fig. 3].

When installing shelves outside the standard location, set

them where they do not interfere with the air intake

vent [page 12 and page 13].

Refer to the accessories on page 62 for the quantity of the shelf

stopper.

Items to be stored in the chamber must be placed on the

shelves. Do not put stored items directly on the bottom of

the chamber.

How to remove the glass door

Move the glass door to the center position when removing

the glass door

Take care to handle the glass door after removing. The rough

handling may cause damage of the glass door or injury.

Marking

Shelf support

Shelf stopper

Fig.3

18

PLACEMENT OF STORED ITEMS

Do not place stored items so as to disrupt the air circulation in the chamber. Disruption of air circulation

can cause the freezing of stored items or can impair the temperature distribution in the chamber.

Air intake vent

Do not block the air intake vent with the stored items. Care should be taken not to put any paper or plastic

chips near the air intake vent. These may be sucked in and block the air intake vent.

Air exhaust vent

Do not block the air exhaust by the stored items near the air exhaust vent. Care should be taken not to

place stored items near to the air exhaust vent. The stored items may become frozen when the

refrigerator is operating at temperature settings lower than 5 oC.

Load line [see figure below]

The storage area is limited to ensure adequate air flow in the chamber. The label “load line” is attached to

the right and left sides of the chamber. Always place stored items within the area limited by these labels.

Stock space

Shelf

Load line

(25)

MPR-S500H: (44)

MPR-S500RH: (37)

Air intake vent

Fron

t

MPR-S500H/S500RH Shelf part

A

ir exhaust

vent

Items

Load line

Shelf

Items

Rear

(57)

Air intake vent

(25)

Load line

Rear Fron

t

Items

Drawer

Items

Drawer

MPR-S500RH Drawer part

Stock space

A

ir exhaust

vent

A

ir flow

A

ir flow

19

USE OF SHELVES AND DRAWERS

Items to be stored in the chamber must be placed on the shelves. Do not put stored items directly on the

bottom of the chamber.

Be careful not to drop the stored items from the front of the shelves when placing the stored items on the shelves

and when removing the stored items from the shelves.

Items to be stored in the chamber must be placed in the

drawers. Do not put stored items directly on the bottom of

the chamber.

Pay attention to the step on the drawer handle when placing the

stored items in the drawer and when removing the stored items

from the drawer.

When pulling out a drawer

Pull out a drawer with pushing the unlock button [Fig. 1] on

the front of the drawer.

When pushing-in a drawer

Push a drawer all the way in until a “click” is heard. The

drawer is locked.

When removing a drawer

Pull out a drawer with pushing the unlock button [Fig. 1] on

the front of the drawer, lift the drawer slightly at the hooked

part of the roller [Fig. 2] and take out the drawer.

When installing a drawer

Lift the front of the drawer slightly, insert it into the rail [Fig.

2], and push it in until a “click” is heard. The drawer is

locked.

Unlock

button Fig. 1

Fig. 2

20

START-UP PROCEDURE

Follow this procedure for the initial operation of the unit and for consequent operations (after temporary

stoppage for cleaning, maintenance or moving) .

After a power failure, the unit will restart operation automatically with the same settings as before the power failure.

1. Check the circuit breaker switch is ON.

2. Connect the power supply cord to the dedicated power source with the appropriate rating with the

chamber empty.

3. Press the standby key on the control panel for more than three seconds.

►The home screen (temperature display screen) is displayed. The red LED lamp blinks. (This is caused

by the high-temperature alarm function and is not a malfunction.)

4. Turn on the battery switch of power failure alarm (when the optional battery kit for power failure alarm

is installed).

“S02:Battery Err” is displayed and the buzzer sounds when the battery switch of power failure alarm is OFF. The

message disappears and the buzzer stops when the battery switch of power failure alarm is turned ON.

5. Set the date and time displayed on the temperature display to the current date and time [pages 49 to

50].

6. Set the desired chamber temperature [page 24].

The factory setting of refrigerator chamber temperature is 5 oC .

7. Open the door to check that the interior light is on.

8. Using the temperature display, check that the chamber temperature has cooled to the set temperature.

9. Gradually place the material inside the chamber.

Putting a large amount of material into the chamber at one time causes the temperature to rise.

Do not block the air intake vent nor air exhaust vent in the chamber.

10. Set a selectable parameter (keypad lock, alarm temperature, delay of door alarm buzzer, etc.) as

required [page 23].

AFTER RECOVERY FROM POWER FAILURE

After recovery from a power failure, the operation will resume automatically with the same settings as

before the power failure. There is no need to re-set. However, always check the operational status

after recovery.

The settings are memorized during power failure by nonvolatile memory.

Pagina se încarcă ...

Phcbi MPR-S500H Instrucțiuni de utilizare

Acest manual este potrivit și pentru

Phcbi MPR-S500H Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente