Important
Please read this “Installation Manual”, and “Instructions for Use”
(separate volume) carefully to familiarize yourself with safe and
effective usage.
•
Refer to the “Instructions for Use” for information on the installation /
connection of the monitor.
•For the latest product information including the “Installation Manual”,
refer to our web site :
http://www.eizoglobal.com
Monochrome LCD monitor
Installation Manual
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
2
CONTENTS
CONTENTS ............................................................. 3
Chapter 1
Basic Operation and Function List
... 4
1-1. Usage of Switches and Operation Guide ... 4
1-2. Basic Operation of the Setting Menu ......... 5
1-3. Function List .................................................. 7
Chapter 2 Adjusting the Screen ........................ 8
2-1. Compatible Resolutions .............................. 8
2-2. Setting the Input Signal ............................... 8
2-3. Selecting Display Mode (CAL Switch
Mode) .............................................................. 9
2-4. Adjusting Brightness ..................................10
●Adjusting the brightness .................................10
●Adjusting the contrast ....................................10
●Adjusting the gamma .....................................11
2-5. Enabling or Disabling Sharpness
Recovery (the Function of Correcting
Image Clarity) ...............................................11
Chapter 3 Controlling Monitor Quality ........... 12
3-1. Using the SelfCalibration Function ...........12
●Executing SelfCalibration ...............................12
●Checking the SelfCalibration results ..............13
3-2. Using the Grayscale Check Function .......13
●Performing Grayscale Check .........................13
●Checking the Grayscale Check results ..........14
3-3. Setting Whether to Display / Hide
Warnings or QC History ..............................14
Chapter 4
Using the Monitor for a Long Time
... 15
4-1. Setting the Power Saving Mode .................15
4-2. Setting Power Saving Mode That Is
Activated When the User Moves Away ......16
Chapter 5 Conguring Monitor Settings ........ 17
5-1. Specifying the Language ............................17
5-2. Showing the Icon for Switching the USB
Ports in the Operation Guide .....................17
5-3. Switching PCs Used to Operate USB
Devices ..........................................................18
5-4.
Automatically Detecting the Input Signal
...18
5-5. Setting the DisplayPort1 Version ...............19
5-6. Setting the DVI Refresh Rate ......................19
5-7. Setting the Image Display Orientation ..... 20
5-8. Adjusting Brightness of the Power
Switch Indicator .......................................... 20
5-9. Skipping Unused Display Modes .............. 20
5-10. Enabling or Disabling DisplayPort
Communication in Power Saving Mode ....21
5-11. Locking Operation Switches ......................21
5-12. Setting Whether to Display / Hide the
Grayscale Warning ..................................... 22
5-13. Enabling or Disabling Sub Pixel Drive ..... 22
5-14. Acquiring Life Estimation Data ................. 23
5-15. Setting Whether to Display / Hide the
EIZO Logo .................................................... 23
5-16. Viewing the Monitor Information .............. 24
5-17. Resetting to Defaults .................................. 24
●Resetting Mode Adjustment Values ...............24
●Resetting all settings ......................................24
Chapter 6 Troubleshooting .............................. 25
6-1. No Picture .................................................... 25
6-2. Imaging Problems ....................................... 26
6-3. Other Problems ........................................... 27
●Error Code Table ........................................... 28
Chapter 7 Reference ........................................ 29
7-1. Arm Installation Procedure........................ 29
7-2. How to Use USB Hub Function .................. 30
7-3. Main Default Settings ..................................31
Appendix .............................................................. 32
Trademark ............................................................... 32
License .................................................................... 32
LIMITED WARRANTY ............................................. 33
Recycling Information ........................................... 34
3
CONTENTS
4Chapter 1 Basic Operation and Function List
Chapter 1
Basic Operation and Function List
1-1. Usage of Switches and Operation Guide
1. Displaying the operation guide
Touch any switch (except ).
The operation guide appears on the screen.
Display Function
Turns the power on or off.
Displays the Setting menu. The Setting menu is used to congure advanced monitor
settings.
Switch PCs using USB devices.
For details on how to perform switching, see “5-3. Switching PCs Used to Operate
USB Devices” (page 18).
Attention
• Not displayed in the operation guide as a default setting. For how to display, see
“5-2. Showing the Icon for Switching the USB Ports in the Operation Guide” (page
17).
Switches display modes. For more information about how to switch display modes,
see “2-3. Selecting Display Mode (CAL Switch Mode)” (page 9).
Selects an item.
Applies the selected content.
Cancels the selection.
5
Chapter 1 Basic Operation and Function List
2.
Adjusting / setting
1. Touch a switch for the icon showing the item you want to set.
The menu appears.
2. Use each switch to congure the setting. If necessary, select to apply the setting.
3.
Exiting
Select to exit the menu.
1-2. Basic Operation of the Setting Menu
1. Displaying the Setting menu
1. Select from the operation guide.
The Setting menu appears.
Note
• To adjust or set "Administrator Settings" items, display the Setting menu according to the following procedure:
1. Select to turn off the monitor.
2. While touching the leftmost switch ( ), touch for more than two seconds to turn on the monitor.
"Administrator Settings" appears.
6Chapter 1 Basic Operation and Function List
2.
Adjusting / setting
1. Select a menu to adjust / set using , then select .
The advanced menu appears.
2. Select an item to adjust / set using , then select .
The Adjustment / Setting menu appears.
3. Adjust / set the selected item using , and then select .
Note
• The settings for "Administrator Settings" items are applied by selecting "Apply".
3.
Exiting
Select several times to exit the Setting menu.
Note
• “Administrator Settings” is exited when you select “Apply”.
7
Chapter 1 Basic Operation and Function List
1-3. Function List
The following table shows the items in the Setting menu.
Main menu Item Reference
CAL Switch Mode Mode “2-4. Adjusting Brightness” (page 10)
Note
• “Contrast” and “ Gamma” can only be adjusted in “ 4-Text ”
mode.
Brightness
Contrast
Gamma
Reset
RadiCS SelfQC SelfCalibration “3-1. Using the SelfCalibration Function” (page 12)
Grayscale Check “3-2. Using the Grayscale Check Function” (page 13)
LEA “5-14. Acquiring Life Estimation Data” (page 23)
Settings “3-3. Setting Whether to Display / Hide Warnings or QC
History” (page 14)
Preferences Input “2-2. Setting the Input Signal” (page 8)
Auto Input Detection “5-4. Automatically Detecting the Input Signal” (page 18)
Power Save “4-1. Setting the Power Saving Mode” (page 15)
Indicator “5-8. Adjusting Brightness of the Power Switch Indicator”
(page 20)
USB Selection “5-2. Showing the Icon for Switching the USB Ports in the
Operation Guide” (page 17)
Presence Sensor “4-2. Setting Power Saving Mode That Is Activated When the
User Moves Away” (page 16)
Mode Skip “5-9. Skipping Unused Display Modes” (page 20)
Monitor Reset “5-17. Resetting to Defaults” (page 24)
Languages “5-1. Specifying the Language” (page 17)
Information “5-16. Viewing the Monitor Information” (page 24)
Administrator
Settings
On-Screen Logo “5-15. Setting Whether to Display / Hide the EIZO Logo”
(page 23)
Key Lock “5-11. Locking Operation Switches” (page 21)
Image Rotation “5-7. Setting the Image Display Orientation” (page 20)
DP Power Save “5-10. Enabling or Disabling DisplayPort Communication in
Power Saving Mode” (page 21)
Grayscale Warning “5-12. Setting Whether to Display / Hide the Grayscale
Warning” (page 22)
Sharpness Recovery “2-5. Enabling or Disabling Sharpness Recovery (the
Function of Correcting Image Clarity)” (page 11)
Signal Format “5-5. Setting the DisplayPort1 Version” (page 19),
“5-6. Setting the DVI Refresh Rate” (page 19),
“5-13. Enabling / Disabling Sub Pixel Drive” (page 22)
8Chapter 2 Adjusting the Screen
Chapter 2 Adjusting the Screen
2-1. Compatible Resolutions
For information about the compatible resolutions of the monitor, see “Compatible Resolutions” in the
Instructions for Use. For information on how to set the resolution on a PC, refer to the manual of the PC.
2-2. Setting the Input Signal
You can select an input signal to be displayed on the screen.
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “Input”, then .
3. Select “Display Port1”, “Display Port2”, or “DVI”, and select .
When the setting is complete, the input port names appear.
Attention
• If you turn the main power off and on again, the input signal is automatically detected regardless of the setting.
• If the PC that outputs the specied signal enters the power saving mode or is turned off when “Auto Input
Detection” is set to “On”, any other available signal is displayed automatically. For details, refer to “5-4.
Automatically Detecting the Input Signal” (page 18).
9
Chapter 2 Adjusting the Screen
2-3. Selecting Display Mode (CAL Switch Mode)
The display mode can be selected according to the monitor application.
Display Modes
√: Can be calibrated
Mode Purpose
1-DICOM Enables display using DICOM® Part 14-compliant grayscale characteristics. √
2- CAL1 Displays the calibration status using calibration software. √
3-CAL2 √
4-Text Suitable to display documents, spreadsheets, or other text. -
Procedure
1. Touch any switch (except ).
2. Select from the operation guide.
The Mode menu appears on the lower right.
1-DICOM
↓
↑
2-CAL1
↓
↑
3-CAL2
↓
↑
4-Text
Example:
3. Modes are changed in sequence each time you select .
You can also select or to change modes when the Mode menu is being displayed.
Note
• The Setting menu and Mode menu cannot be displayed at the same time.
10 Chapter 2 Adjusting the Screen
2-4. Adjusting Brightness
Brightness levels can be adjusted and saved for each mode.
Attention
• It takes about 15 minutes for the monitor display to stabilize. After turning on the monitor power, or after the
monitor has recovered from power saving mode, wait until 15 minutes or more have passed to perform various
quality control tests, calibrations, or screen adjustment of the monitor.
Note
• Use values shown in “%” for reference.
●Adjusting the brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Setting Range
0 to 100 %
Procedure
1. Select “CAL Switch Mode” from the Setting menu, then select .
2. Select “Brightness”, then .
3. Specify the setting using or .
4. Select after completing the setting.
●Adjusting the contrast
The brightness of the screen is adjusted by varying the video signal level.
Note
• Contrast can only be adjusted in “4-Text” mode.
Setting Range
0 to 100 %
Procedure
1. Select “CAL Switch Mode” from the Setting menu, then select .
2. Select “Contrast”, then .
3. Specify the setting using or .
4. Select after completing the setting.
Note
• When the contrast is set to 100 %, all the gradations are shown.
• When adjusting the monitor, it is recommended to perform brightness adjustment, which does not lose
gradation characteristics, prior to contrast adjustment.
• If the screen seems bright, the screen can also be dimmed by lowering the contrast. Lowering the contrast
reduces the amount gradation that is displayed.
11
Chapter 2 Adjusting the Screen
●Adjusting the gamma
Adjust the gamma. While the brightness of the monitor varies depending on the input signal, the
variation rate is not proportional to the input signal. Maintaining the balance between the input signal
and brightness of the monitor is referred to as “Gamma correction”.
Note
• Contrast can only be adjusted in “4-Text” mode.
Setting Range
1.6 to 2.7
Procedure
1. Select “CAL Switch Mode” from the Setting menu, then select .
2. Select “Gamma”, then .
3. Specify the setting using or .
4. Select after completing the setting.
2-5. Enabling or Disabling Sharpness Recovery (the
Function of Correcting Image Clarity)
EIZO’s unique technology called “Sharpness Recovery” displays images that are true to the original
source data by correcting variations in the LCD panel.
Procedure
1. Select to turn off the monitor.
2. While touching the leftmost switch ( ), touch for more than two seconds to turn on the
monitor.
3. Select “Sharpness Recovery” in “Administrator Settings”, then select .
4. Select “On” or “Off”, then select .
5. Select “Apply”, and then select .
Attention
• After changing the setting, perform a visual check according to the medical standards / guidelines.
12 Chapter 3 Controlling Monitor Quality
Chapter 3 Controlling Monitor Quality
The monitor includes the Integrated Front Sensor, which enables you to perform calibration and Grayscale
Check independently.
Note
• Calibration can be performed periodically by using the schedule function of RadiCS LE that is attached to the
monitor. For more information about the setup procedure, refer to the RadiCS LE User’s Manual (stored on the
CD-ROM).
• RadiCS enables you to congure the schedule settings for Grayscale Check as well as for calibration. For more
information about the setup procedure, refer to the RadiCS User’s Manual.
• If you want to perform high-level quality control in compliance with medical standards / guidelines, use optional
quality control software kit "RadiCS UX2".
• To adjust measurement results of the Integrated Front Sensor to those of an EIZO external sensor (UX1 or UX2
sensor), perform correlation between the Integrated Front Sensor and the external sensor using RadiCS / RadiCS
LE. Periodical correlation allows you to maintain the measurement accuracy of the Integrated Front Sensor at a
level equivalent to that of the external sensor. For details, refer to the RadiCS / RadiCS LE User’s Manual.
3-1. Using the SelfCalibration Function
Execute SelfCalibration and view the latest results.
●Executing SelfCalibration
Procedure
1. Select “RadiCS SelfQC” from the Setting menu, then select .
2. Select “SelfCalibration” for “RadiCS SelfQC”, then select .
3. Select “Execute”, then .
SelfCalibration is executed.
Attention
• If the power to the PC is turned off or the input signal switches while SelfCalibration is running, the execution
will be canceled.
• After SelfCalibration is complete, perform Grayscale Check at the same room temperature and illuminance
as those in the actual working environment.
Note
• The following items can be set by using RadiCS / RadiCS LE. For more information about the setup
procedure, refer to the RadiCS / RadiCS LE User’s Manual.
-Calibration target
-SelfCalibration schedule
-The next execution schedule is displayed in the advanced menu if the schedule was set in RadiCS / RadiCS
LE.
• The calibration target value can be conrmed by selecting the target mode in "CAL Switch mode" of the
Setting menu.
13
Chapter 3 Controlling Monitor Quality
●Checking the SelfCalibration results
Attention
• The results can be checked when "QC History" is set to "On" (see “3-3. Setting Whether to Display / Hide
Warnings or QC History” (page 14)).
Procedure
1. Select “RadiCS SelfQC” from the Setting menu, then select .
2. Select “SelfCalibration”, then .
3. Select “Result”, then .
4. Select “DICOM”, “CAL1”, or “CAL2”, then select .
The SelfCalibration results (such as Max. Error Rate, Last Time, and Error Code) are displayed.
3-2. Using the Grayscale Check Function
Perform Grayscale Check and view the latest results. Furthermore, if you have congured the schedule
using RadiCS, the next execution schedule is displayed.
●Performing Grayscale Check
Attention
• Perform the Grayscale Check based on the actual color temperature and brightness of the working
environment.
Procedure
1. Select “RadiCS SelfQC” from the Setting menu, then select .
2. Select “Grayscale Check”, then .
3. Select “Execute”, then .
Grayscale Check is executed.
Attention
• The determination value for Grayscale Check can be specied from RadiCS. Refer to the RadiCS User’s
Manual for details.
• The Grayscale Check schedule can be congured using RadiCS. For more information about the setup
procedure, refer to the RadiCS User’s Manual. If you have congured the schedule using RadiCS, the next
execution schedule is displayed in the advanced menu.
14 Chapter 3 Controlling Monitor Quality
●Checking the Grayscale Check results
Attention
• The results can be checked when "QC History" is set to "On".
Procedure
1. Select “RadiCS SelfQC” from the Setting menu, then select .
2. Select “Grayscale Check”, then .
3. Select “Result”, then .
4. Select “DICOM”, “CAL1”, or “CAL2”, then select .
Up to ve past Grayscale Check results (Passed, Failed, Canceled, or Error) are displayed.
3-3. Setting Whether to Display / Hide Warnings or QC
History
You can set whether to display or hide warnings related to “Failed” Grayscale Check results, or the
execution results (QC History) of SelfCalibration, Grayscale Check, etc.
Procedure
1. Select “RadiCS SelfQC” from the Setting menu, then select .
2. Select “Settings”, then .
3. Select “Warning” or “QC History”.
4. Select “On” or “Off”, then select .
15
Chapter 4 Using the Monitor for a Long Time
Chapter 4 Using the Monitor for a Long Time
The monitor can be set to enter the power saving mode according to the PC status or the user’s movement.
The life of the monitor backlight can be extended by setting the monitor to enter the power saving mode
when the monitor is not used.
4-1. Setting the Power Saving Mode
You can specify whether the monitor enters the power saving mode according to the PC status.
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “Power Save”, then .
3. Select “High”, “Low”, or “Off”, and select .
Setting Function
High Turns the backlight off. This provides the highest power saving effect.
Low Sets the backlight to the lowest lighting level. The time until operation stabilizes after
restoring from power saving mode can be reduced.
Off Does not enable the power saving mode. The backlight lights up irrespective of the PC
status. This setting may shorten the backlight life.
Attention
• When not using the monitor, you can turn off the main power supply or disconnect the power plug so that the
power is cut completely.
• Devices connected to the USB upstream port and downstream port still work when the monitor is in the power
saving mode or when the power is switched off using the power button ( ) of the monitor. For this reason,
power consumption of the monitor varies with connected devices even in the power saving mode.
Note
• When the signal input from the PC is no longer detected, a message appears notifying the user of the transition to
the power saving mode. The monitor enters power saving mode ve seconds after the message appears.
• When power save is set to “High” or “Low”, the status of the monitor can be conrmed by checking the color of the
lamp on the power switch.
Power indicator Monitor status PC status
Green Normal operation mode On
Orange Power saving mode Off or power saving mode
16 Chapter 4 Using the Monitor for a Long Time
4-2. Setting Power Saving Mode That Is Activated When
the User Moves Away
By setting the Presence Sensor, you can set the monitor to automatically enter the power saving mode
and display no images on the screen when the user moves away from the monitor. The monitor returns
from the power saving mode when the user moves closer to the monitor. The length of time to pass
before the monitor enters the power saving mode can be specied according to the operating
environment of the monitor or the user’s movement.
Attention
• This feature is not available when "RadiCS SelfQC" is running.
• This feature is not available when "Power Save" is set to "Off".
Note
• At the time of shifting to the power saving mode, a message appears notifying the user of the transition.
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “Presence Sensor”, then .
3. Select “On” or “Off”, then select .
4. When you have selected “On”, congure the advanced settings.
Setting Setting range Description
Time 5, 30 sec
1, 3, 5, 10, 15, 30, 45,
60 min
Specify the length of time to pass before the "No presence
detected." message appears after the user moves away from the
monitor. If the message appears, the monitor enters the power
saving mode after approximately 20 seconds.
Sensitivity Level 5
Level 4
Level 3
Level 2
Level 1
A larger setting value allows the sensor to detect the user’s
movement more sensitively. This makes it difcult for the monitor to
enter the power saving mode. On the other hand, a smaller setting
value allows the sensor to detect only distinct movement of the user
and consequently enables the monitor to enter the power saving
mode more easily. The Presence Sensor functions by detecting the
movement of heat using the sensor on the front of the monitor. The
sensitivity varies with the user’s clothing and ambient temperature.
If you nd transition to the power saving mode or recovery from it
occurs unexpectedly, change the setting value.
Reset - Resets all settings related to the Presence Sensor to their default
values.
Note
• The sensitivity becomes lower at high ambient temperatures. In this environment, you can set a larger
sensitivity value for your easier operation. On the other hand, the sensitivity becomes higher at low
temperatures, and accordingly a smaller sensitivity value is required.
17
Chapter 5 Conguring Monitor Settings
Chapter 5 Conguring Monitor Settings
5-1. Specifying the Language
The language for the Setting menu and messages can be selected.
Selectable Languages
English, Germany, French, Spanish, Italian, Swedish, Japanese, Chinese (simplied), Chinese
(traditional)
Procedure
1. Select “Languages” from the Setting menu, then select .
2. Select a language, then .
5-2. Showing the Icon for Switching the USB Ports in
the Operation Guide
You can specify whether to display in the operation guide.
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “USB Selection”, then .
3. Select “On” or “Off”, then select .
If “On” is selected, the icon for switching the USB ports is shown in the operation guide.
Attention
• If "Off" is specied, the PC currently connected to "USB-1" is enabled even when "USB-2" is selected.
18 Chapter 5 Conguring Monitor Settings
5-3. Switching PCs Used to Operate USB Devices
Switch PCs used to operate USB devices.
Attention
• Before changing the setting, remove all USB memory devices from the monitor if connected. Otherwise, data may
be lost or damaged.
• The PC used for monitor quality control purposes must be connected to .
Note
• PCs that use USB devices can be switched in connection with input signal switching and mouse position by using
RadiCS / RadiCS LE.
• For details, refer to the Instructions for Use for RadiCS / RadiCS LE.
Procedure
1. Touch any switch (except ).
2. Select from the operation guide.
3. Select “USB-1” or “USB-2”, and then select .
Select the USB upstream port to which the PC used for operation is connected.
5-4. Automatically Detecting the Input Signal
This product automatically detects the connector through which a signal is input, and displays the signal
on the screen.
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “Auto Input Detection” from “Preferences”, then select .
3. Select “On” or “Off”, then select .
Setting Function
On Automatically detects the connector through which a signal is input, and displays the
signal on the screen.
If the PC that is outputting the signal displayed on the screen enters the power saving
mode or is turned off when multiple PCs are connected, any other available signal is
displayed automatically.
Off Displays the selected input signal regardless of whether or not it is available.
When you want to switch the input signal, see “2-2. Setting the Input Signal” (page 8).
Note
• If you turn the main power off and on again, the input signal is automatically detected regardless of the
setting.
19
Chapter 5 Conguring Monitor Settings
5-5. Setting the DisplayPort1 Version
You can set the DisplayPort1 version.
Attention
• To use a daisy-chain connection, set the version to “1.2”.
• When a PC is connected via the DisplayPort connector, the DisplayPort version may differ depending on the PC,
and consequently the screen may not appear. In this case, try changing the following settings.
• DisplayPort2 is locked in version “1.1”.
Procedure
1. Select to turn off the monitor.
2. While touching the leftmost switch ( ), touch for more than two seconds to turn on the
monitor.
3. Select “Signal Format” from “Administrator Settings”, then select .
4. Select “DisplayPort1”, then .
5. Select “Version”, then .
6. Select “1.1” or “1.2”, then select .
7. Select “Apply”, and then select .
5-6. Setting the DVI Refresh Rate
Set the DVI refresh rate (screen update frequency) to suit your environment.
Procedure
1. Select to turn off the monitor.
2. While touching the leftmost switch ( ), touch for more than two seconds to turn on the
monitor.
3. Select “Signal Format” from “Administrator Settings”, then select .
4. Select “DVI”, then .
5. Select “Preferred Refresh Rate”, then .
6. Select “Low” or “High”, then select .
Setting Refresh rate
Low 25 Hz
High 50 Hz
7. Select “Apply”, and then select .
20 Chapter 5 Conguring Monitor Settings
5-7. Setting the Image Display Orientation
This function allows you to change the image display orientation according to the monitor installation
orientation.
Procedure
1. Select to turn off the monitor.
2. While touching the leftmost switch ( ), touch for more than two seconds to turn on the
monitor.
3. Select “Image Rotation” from “Administrator Settings”, then select .
4. Select “Portrait” or “Landscape”, then select .
Setting Monitor orientation
Portrait Select this when the monitor is installed in
portrait orientation.
Landscape Select this when the monitor is installed in
landscape orientation.
5. Select “Apply”, and then select .
5-8. Adjusting Brightness of the Power Switch Indicator
The brightness of the power switch indicator (green) while the screen is displayed can be adjusted. The
larger the set value, the brighter the power indicator lights up. On the other hand, the smaller the value,
the darker it becomes. The “Off” setting turns off the power switch indicator.
Setting Range
1 to 7, Off
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “Indicator”, then .
3. Specify the setting using or .
4. When the setting is complete, select .
5-9. Skipping Unused Display Modes
This function allows you to skip certain display modes when selecting a mode.
Please use this function if you want to limit the modes to be displayed, or avoid changing the display
status randomly.
Procedure
1. Select “Preferences” from the Setting menu, then select .
2. Select “Mode Skip”, then .
3. Select a mode whose setting you want to change, then select .
4. Select “Skip” or “-”, then select .
Attention
• Not all modes can be disabled (skipped). Set at least one mode to "-".
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
în alte limbi
- English: Eizo GX560 Owner's manual
Lucrări conexe
-
Eizo MX315W Manualul proprietarului
-
-
-
-
-
-
Eizo GX320 Manualul proprietarului
-
-
-
Eizo GX550 Manualul proprietarului