Parkside PDSSA 20-Li A1 Translation Of The Original Instructions

CORDLESS IMPACT DRIVER PDSSA 20-Li A1

AKKU-DREHSCHLAGSCHRAUBER

Originalbetriebsanleitung

IAN 339111_1910

CORDLESS IMPACT DRIVER

Translation of the original instructions

АКУМУЛАТОРЕН УДАРЕН

ВИНТОВЕРТ

Превод на оригиналното ръководство за експлоатация

MAȘINĂ DE ÎNȘURUBAT FĂRĂ FIR

Traducerea instrucţiunilor de utilizare original

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ

ΠΑΛΜΙΚΟ ΚΑΤΣΑΒΙΔΙ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

AKU UDARNI ODVIJAČ

Prijevod originalnih uputa za uporabu

AKU UDARNI ODVIJAČ

Prevod originalnog uputstva za upotrebu

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 13

RS Prevod originalnog uputstva za upotrebu Strana 25

RO Traducerea instrucţiunilor de utilizare original Pagina 37

BG Превод на оригиналното ръководство за експлоатация Cтраница 49

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 63

DE / AT / CH Originalbetriebsanleitung Seite 77

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

20V max.

18V

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3/PDSLG 20 A1 of the

X20V Team series are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger PLG 20 A1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

60 min

2,4 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

35 min

3,5 A

45 min

4,5 A

60 min

4,5 A

max. 4.5 A

Charger PDSLG 20 A1

35 min

3,5 A

45 min

4,5 A

60 min

4,5 A

PDSSA 20-Li A1

GB

│

CY

│

1 ■

Contents

Introduction .........................................................2

Intended use .................................................................... 2

Features ........................................................................ 2

Package contents ................................................................. 2

Technical data ................................................................... 2

General power tool safety warnings .....................................3

1. Work area safety .............................................................. 3

2. Electrical safety ................................................................ 4

3. Personal safety ................................................................ 4

4. Power tool use and care ......................................................... 5

5. Battery tool use and care ........................................................ 5

6. Service ....................................................................... 6

Safety instructions speciﬁcally for impact screwdrivers .................................... 6

Original accessories/additional equipment ............................................ 6

Safety guidelines for battery chargers ................................................. 7

Before use ...........................................................7

Charging the battery pack (seeﬁg.A) ................................................ 7

Attaching/disconnecting the battery pack to/from the appliance ........................... 8

Checking the battery charge level .................................................... 8

Use .................................................................8

Switching on and oﬀ .............................................................. 8

Setting the speed/tightening torque .................................................. 8

Changing the direction of rotation .................................................... 8

Inserting the bits .................................................................. 8

Maintenance and cleaning .............................................8

Kompernass Handels GmbH warranty ...................................9

Service .............................................................10

Importer ...........................................................10

Disposal ............................................................10

Translation of the original Conformity Declaration .........................11

Ordering a replacement battery ........................................12

Telephone ordering ..............................................................12

IB_339111_PDSSA20-LiA1_LB7.indb 1 18.03.20 12:18

PDSSA 20-Li A1

■ 2

│

GB

│

CY

CORDLESS IMPACT DRIVER

PDSSA 20-Li A1

Introduction

Congratulations on the purchase of your new

appliance. You have chosen a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product,

please familiarise yourself with all operating and

safety instructions. Use the product only as described

and for the range of applications speciﬁed. Please

also pass these operating instructions on to any

future owner.

Intended use

This appliance is intended for screwing in and

unscrewing screws as well as for tightening and

loosening nuts. The appliance has clockwise/

anticlockwise rotation, a 1/4” hexagon socket bit

holder and an LED working light. The light on this

appliance is intended to illuminate the immediate

work area of the appliance. The rotary impact

function of the appliance enables the power of the

motor to be converted into uniform rotary impacts.

The impact mechanism comes into eﬀect during

tightening and loosening.

The appliance is designed for use by adults.

Young people under 16 years of age may only

use the appliance under supervision. The manufac-

turer accepts no liability for damages caused by

improper use or incorrect operation of the appli-

ance.

Use this product only as described and for the

areas of applications speciﬁed. The appliance is

not intended for commercial use. Any other usage

or modiﬁcation of the appliance is deemed to be

improper and carries a signiﬁcant risk of accidents.

The manufacturer accepts no responsibility for

damage(s) attributable to misuse.

Features

Tool holder

Locking sleeve

Bit holder (magnetic)

Rotation direction switch/lock

Belt clip

Battery charge level button

Battery display LED

Battery pack*

Release button for battery pack

LED work light

ON/OFF switch/Speed control

Adapter to 1/4” square

Bit holder

High-speed charger*

Red charge control LED

Green charge control LED

Package contents

1 cordless impact driver PDSSA 20-Li A1

1 adapter from hex (1/4”) to square

1 1/4” extension (50 mm)

1 belt clip

1 carrying case

1 set of operating instructions

Technical data

Cordless impact driver PDSSA 20-Li A1

Rated voltage 20 V (DC)

Idle speed n

0

0–2800 rpm

Rated stroke rate 0–3600 ipm

Max. torque 180 Nm

Suitable for metal screws ≤ M8

Suitable for wood screws ≤ 8 mm Ø

Tool holder 1/4”

Use only the following battery to operate the

cordless tool PAP 20 A1*

Type LITHIUM ION

Rated voltage 20 V

(DC)

Capacity 2 Ah

Cells 5

IB_339111_PDSSA20-LiA1_LB7.indb 2 18.03.20 12:18

PDSSA 20-Li A1

GB

│

CY

│

3 ■

Use only the following high-speed battery

charger to charge the cordless tool

PLG20A1*

INPUT

Rated voltage 230–240 V ∼, 50 Hz

(AC)

Rated power consumption 65 W

Fuse (internal) 3.15 A

T3.15A

OUTPUT

Rated voltage 21.5 V (DC)

Rated current 2.4 A

Charging time approx. 60 min

Protection class II /

(double insulation)

* BATTERY AND CHARGER NOT INCLUDED IN

DELIVERY

Noise emission value

Noise measurement value determined in accord-

ance with EN 62841. The A-rated noise level

of the tool is typically:

Sound pressure level L

PA

= 79.4 dB (A)

Uncertainty K

PA

= 3 dB

Sound power level L

WA

= 90.4 dB (A)

Uncertainty K

WA

= 3 dB

Vibration emission value

Total vibration values (vector total of three directions)

determined in accordance with EN 62841:

Tightening screws and nuts of maximum

permissible size a

h

= 5.677 m/s

2

Uncertainty K = 1.5 m/s

2

Wear hearing protection!

NOTE

►

The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with a

standardised test procedure and can be used

for comparison of the power tool with

another tool.

► The speciﬁed total vibration values and the

noise emission values can also be used to

make a provisional load estimate.

WARNING!

► Depending on the manner in which the

power tool is being used, and in particular

the kind of workpiece that is being worked,

the vibration and noise emission values can

deviate from the values given in these instruc-

tions during actual use of the power tool.

► Try to keep the load as low as possible.

Measures to reduce the vibration load are,

e.g. wearing gloves and limiting the working

time. Wherein all states of operation must be

included (e.g. times when the power tool is

switched oﬀ and times where the power tool

is switched on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings, instructions,

illustrations and speciﬁcations provided

with this power tool. Failure to follow all

instructions listed below may result in electric

shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term „power tool“ in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

IB_339111_PDSSA20-LiA1_LB7.indb 3 18.03.20 12:18

PDSSA 20-Li A1

■ 4

│

GB

│

CY

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entan-

gled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment

such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles. A careless

action can cause severe injury within a fraction

of a second.

IB_339111_PDSSA20-LiA1_LB7.indb 4 18.03.20 12:18

PDSSA 20-Li A1

GB

│

CY

│

5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that

cannot be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detach-

able, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool acci-

dentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unex-

pected situations.

5. Battery tool use and care

a) Recharge only with the charger speciﬁed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

ﬁre when used with another battery pack.

b) Use power tools only with speciﬁcally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁre.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a ﬁre.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable behaviour

resulting in ﬁre, explosion or risk of injury.

f) Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre or

temperature above 130 °C (265°F) may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instruc-

tions. Charging improperly or at temperatures

outside the speciﬁed range may damage the

battery and increase the risk of ﬁre.

IB_339111_PDSSA20-LiA1_LB7.indb 5 18.03.20 12:18

PDSSA 20-Li A1

■ 6

│

GB

│

CY

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Protect the rechargeable battery

from heat, for example from

continuous exposure to sunlight,

ﬁre, water and moisture.

There is a risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

Safety instructions speciﬁcally for

impact screwdrivers

■ Wear hearing protection when impact

screwing. Exposure to loud noise can lead to

hearing loss.

■ Secure the workpiece! A workpiece securely

held by a clamping device or vice is much safer

than one held in your hand.

■ Hold the power tool ﬁrmly. High torques can

occur for brief periods while tightening and

loosening screws.

■ Wait until the power tool has come to a stand-

still before putting it down. The tool can jam,

this leading to loss of control of the appliance.

■ Always hold the tool by its insulated handles

when working with power tools that may come

into contact with hidden electrical cables.

Fasteners contacting a “live” wire may make

exposed metal parts of the power tool “live”

and could give the operator an electric shock.

Original accessories/additional

equipment

■ Only use the accessories and additional

equipment that are speciﬁed in the operating

instructions and are compatible with the

appliance.

WARNING!

■ Do not use any accessories which are not

recommended by PARKSIDE. This can lead to

an electric shock and ﬁre.

IB_339111_PDSSA20-LiA1_LB7.indb 6 18.03.20 12:18

PDSSA 20-Li A1

GB

│

CY

│

7 ■

Safety guidelines for battery chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited phys-

ical, sensory or mental capabilities

or lack of experience and know-

ledge, provided that they are under

supervision or have been told how

to use the appliance safely and are

aware of the potential risks. Do not

allow children to use the appliance

as a toy. Cleaning and user mainte-

nance tasks may not be carried out

by children unless they are super-

vised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for

indoor use only.

WARNING!

■ To avoid potential risks, damaged mains

cables should be replaced by the manufac-

turer, their customer service department or a

similarly qualiﬁed person.

ATTENTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/PAP 20 A3

.

♦ A current list of battery compatibility can be

found at www.lidl.de/Akku.

ATTENTION!

Hot surface.

Risk of burns.

Before use

Charging the battery pack

(seeﬁg.A)

CAUTION!

► Always unplug the appliance before you

remove the battery pack from or connect the

battery pack to the charger.

NOTE

►

Never charge the battery pack if the ambient

temperature is below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level

is between 50% and 80%. The storage climate

should be cool and dry and the ambient

temperature should be between 0°C and

50°C.

♦ Connect the battery pack to the rapid

battery charger (see Fig. A).

♦ Insert the power plug into the socket. The

control LED lights up red.

♦ The green control LED indicates that the

charging process is complete and the battery

pack is ready.

CAUTION!

♦ If the red control LED ﬂashes, this means

that the battery pack has overheated and

cannot be charged.

♦ If the red and green control LEDs

both

ﬂash, this means that the battery pack is

defective.

♦ Insert the battery pack back into the

appliance.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

IB_339111_PDSSA20-LiA1_LB7.indb 7 18.03.20 12:18

PDSSA 20-Li A1

■ 8

│

GB

│

CY

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack

♦ Push the rotation direction switch into

the middle position (lock). Allow the battery

pack

to click into the handle.

Removing the battery pack

♦ Press the release button and remove the

battery pack.

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram).

The status/remaining charge will be shown on

the battery display LED as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Use

Switching on and oﬀ

Switching on

♦ To start the appliance, press the ON/OFF

switch and keep it pressed in. The LED work

light lights up when the ON/OFF switch

is depressed lightly or fully. This allows for illumi-

nation of the work area in low lighting.

Switching oﬀ

♦ Release the ON/OFF switch to switch oﬀ the

appliance.

Setting the speed/tightening torque

♦ Press the ON/OFF switch lightly for a low

speed/tightening torque. Increasing the pressure

increases the speed/tightening torque.

■ The tightening torque depends on the selected

speed and impact duration.

CAUTION!

♦ The tightening torque actually attained must

always be checked with a torque wrench!

NOTE

►

The integrated motor brake ensures rapid

stoppage.

Changing the direction of rotation

♦ Change the direction of rotation by pressing the

rotational direction switch towards the left or

right.

Inserting the bits

♦ Insert the adapter or bit holder into the

tool holder .

♦ To do this, pull the locking sleeve backwards

and allow the adapter or bit holder to

engage.

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

The appliance is maintenance-free.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Never allow liquids to get into the appliance.

■ Use a soft, dry cloth to clean the housing.

Never use petrol, solvents or cleansers which

can damage plastic.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

NOTE

►

Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

IB_339111_PDSSA20-LiA1_LB7.indb 8 18.03.20 12:18

PDSSA 20-Li A1

GB

│

CY

│

9 ■

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from the

date of purchase. If this product has any faults, you,

the buyer, have certain statutory rights. Your statu-

tory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating

instructions for the product regarding proper use of

the product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper

handling, use of force and modiﬁcations/repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and information

about what the defect is and when it occurred.

IB_339111_PDSSA20-LiA1_LB7.indb 9 18.03.20 12:18

PDSSA 20-Li A1

■ 10

│

GB

│

CY

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to

the Lidl service page (www.lidl-service.com) where

you can open your operating instructions by

entering the item number (IAN) 123456.

Service

WARNING!

► Have the power tool repaired by the service

centre or a qualiﬁed electrician and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

► Always ensure that the power plug or the

mains cable is replaced only by the manu-

facturer of the appliance or by an

approved customer service provider. This

will ensure that the safety of the appliance is

maintained.

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 339111_1910

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Disposal

The packaging is made from environ-

mentally friendly material and can be

disposed of at your local recycling plant.

Do not dispose of power tools

in your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in an environ-

mentally compatible manner.

Do not dispose of batteries in

your normal household waste!

Defective or worn-out rechargeable

batteries must be recycled according

to Directive 2006/66/EC. Take the battery pack

and/or appliance to a nearby collection facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The pack-

aging material is labelled with abbreviations (a)

and numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

IB_339111_PDSSA20-LiA1_LB7.indb 10 18.03.20 12:18

PDSSA 20-Li A1

GB

│

CY

│

11 ■

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, docu ment oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the

declaration described above complies with the requirements of the Directive 2011/65/EU of the European

Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and

electronic appliances.

Applied harmonised standards:

EN 62841-1:2015

EN 62841-2-2:2014

EN 60335-1:2012/A13:2017

EN 60335-2-29:2004/A2:2010

EN 62233:2008

EN 55014-1:2017

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type/appliance designation: Cordless impact driver PDSSA 20-Li A1

Year of manufacture: 01–2020

Serial number: IAN 339111_1910

Bochum, 22/01/2020

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

IB_339111_PDSSA20-LiA1_LB7.indb 11 18.03.20 12:18

PDSSA 20-Li A1

■ 12

│

GB

│

CY

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the

Internet on www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

►

Online ordering of replacement parts might not be possible in some countries. In this is the case,

please contact the Service hotline.

Telephone ordering

Service Great Britain Tel.: 0800 404 7657

CY

Service Cyprus Tel.: 8009 4409

To ensure a fast processing of your order, have the article number of your appliance to hand (e.g.

IAN339111) in case of questions. The article number can be found on the type plate or the title

page of these instructions.

IB_339111_PDSSA20-LiA1_LB7.indb 12 18.03.20 12:18

PDSSA 20-Li A1

HR

│

13 ■

Sadržaj

Uvod ..............................................................14

Namjenska uporaba .............................................................14

Oprema .......................................................................14

Opseg isporuke .................................................................14

Tehnički podaci .................................................................14

Opće sigurnosne napomene za uporabu električnog alata ..................15

1. Sigurnost na radnom mjestu .....................................................16

2. Električna sigurnost ............................................................16

3. Sigurnost osoba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4. Korištenje i rukovanje električnim alatom ............................................17

5. Korištenje i rukovanje baterijskim alatom ............................................17

6. Servis .......................................................................18

Sigurnosne napomene speciﬁčne zaudarne odvijače ...................................18

Originalni pribor/dodatni uređaji ...................................................18

Sigurnosne napomene za punjače ..................................................19

Prije uključivanja uređaja .............................................19

Punjenje paketa baterije (vidislikuA) ................................................19

Umetanje/vađenje paketa baterija izuređaja .........................................20

Provjera stanja baterije ...........................................................20

Uključivanje uređaja .................................................20

Uključivanje/isključivanje ..........................................................20

Prilagođavanje broja okretaja/ momenta pritezanja .....................................20

Promjena smjera okretanja ........................................................20

Umetanje bitova .................................................................20

Održavanje i čišćenje .................................................20

Jamstvo tvrtke Kompernass Handels GmbH ..............................21

Servis ..............................................................22

Uvoznik ............................................................22

Zbrinjavanje ........................................................22

Originalna izjava o sukladnosti ........................................23

Narudžba zamjenske baterije .........................................24

Telefonska narudžba .............................................................24

IB_339111_PDSSA20-LiA1_LB7.indb 13 18.03.20 12:18

PDSSA 20-Li A1

■ 14

│

HR

AKU UDARNI ODVIJAČ

PDSSA 20-Li A1

Uvod

Čestitamo na kupnji Vašeg novog uređaja. Time ste

se odlučili za vrlo kvalitetan proizvod. Upute za

uporabu dio su opreme ovog proizvoda. One sadr-

že važne napomene za sigurnost, rukovanje i zbri-

njavanje. Prije uporabe proizvoda upoznajte se sa

svim napomenama za rukovanje i svim sigurnosnim

napomenama. Proizvod koristite isključivo na opisa-

ni način i u navedenim područjima uporabe. U slu-

čaju predaje proizvoda trećim osobama

predajte i svu dokumentaciju.

Namjenska uporaba

Ovaj uređaj je namijenjen za uvrtanje i odvijanje

vijaka, kao i za zatezanje i otpuštanje matica.

Uređaj ima desni/lijevi hod, unutrašnji šesterokutni

prihvat za bitove dimenzija 1/4“ i LED-radno

svjetlo. Svjetlo ovog uređaja namijenjeno je za

osvjetljavanje neposrednog radnog područja ure-

đaja. Funkcija udarnog okretanja uređaja snagu

motora pretvara u ravnomjerne okretne udare.

Udari nastupaju prilikom zatezanja i otpuštanja.

Uređaj je namijenjen da njime rukuju odrasle osobe.

Mladi stariji od 16 godina uređaj smiju koristiti

samo pod nadzorom. Proizvođač ne odgovara za

štete nastale uporabom uređaja suprotno njegovoj

namjeni ili pogrešnim rukovanjem.

Uređaj koristite samo na opisani način i u opisanim

područjima uporabe. Uređaj nije namijenjen za

komercijalnu uporabu. Svaki drugi način uporabe

isvaka izmjena uređaja smatra se nenamjenskom

ikrije znatnu opasnost od nezgode. Proizvođač ne

preuzima odgovornost za štete nastale uslijed

nenamjenskog korištenja uređaja.

Oprema

Prihvatnik alata

Čahura za blokadu

Držač bitova (magnetni)

Sklopka za odabir smjera okretanja/blokada

Kopča za pojas

Tipka za stanje baterije

LED indikator baterije

Paket baterija*

Tipka za deblokadu paketa baterija

LED radno svjetlo

Sklopka za uključivanje/isključivanje/

Regulacija broja okretaja

Adapter na 1/4“ četverokutni oblik

Držač nastavaka

Brzi punjač*

Crveni LED indikator za kontrolu punjenja

Zeleno LED svjetlo za kontrolu punjenja

Opseg isporuke

1 aku udarni odvijač PDSSA 20-Li A1

1 adapter na 1/4“ četverokutni oblik

1 1/4“ produžetak (50 mm)

1 kopča za pojas

1 kovčeg za nošenje

1 upute za uporabu

Tehnički podaci

Aku udarni odvijač PDSSA 20-Li A1

Nazivni napon 20 V

(istosmjerna struja)

Broj okretaja u praznom hodu n

0

0 – 2800 min

-1

Nazivni broj udaraca 0 – 3600 min

-1

Maks. okretni moment 180 Nm

Prikladan za vijke za metal ≤ M8

Prikladan za vijke za drvo ≤ 8 mm Ø

Stezna glava za alat 1/4“

IB_339111_PDSSA20-LiA1_LB7.indb 14 18.03.20 12:18

PDSSA 20-Li A1

HR

│

15 ■

Za pogon alata s pogonom na baterije kori-

stite isključivo sljedeću bateriju PAP 20 A1*

Tip LITIJ-IONSKA

Nazivni napon 20 V

(istosmjerna struja)

Kapacitet 2 Ah

Broj ćelija 5

Za punjenje alata s pogonom na baterije

koristite isključivo sljedeći brzi punjač

PLG 20 A1*

ULAZ/Input

Nazivni napon 230 – 240 V ∼, 50 Hz

(izmjenična struja)

Nazivna snaga 65 W

Osigurač (unutarnji) 3,15 A

T3.15A

IZLAZ/Output

Nazivni napon 21,5 V

(istosmjerna struja)

Nazivna struja 2,4 A

Trajanje punjenja otpr. 60 min

Razred zaštite II /

(dvostruka izolacija)

* BATERIJA I PUNJAČ NISU SADRŽANI U

OPSEGU ISPORUKE

Vrijednost emisije buke

Vrijednost buke izmjerena sukladno normi

EN62841. Standardna razina emisije buke

električnog alata „A” obično iznosi:

Razina zvučnog tlaka L

PA

= 79,4 dB (A)

Odstupanje K

PA

= 3 dB

Razina zvučnog učinka L

WA

= 90,4 dB (A)

Odstupanje K

WA

= 3 dB

Vrijednost emisije vibracija

Ukupne vrijednosti vibracija (zbroj vektora triju

smjerova) izračunate su u skladu s normom

EN 62841:

Zatezanje vijaka i matica maksimalne dopuštene

veličine a

h

= 5,677 m/s

2

Odstupanje K = 1,5 m/s

2

Nosite zaštitu sluha!

NAPOMENA

►

Navedene ukupne vrijednosti vibracija i nave-

dene vrijednosti emisije buke izmjerene su

standardiziranom metodom ispitivanja i mogu

se koristiti za usporedbu električnih alata.

► Navedene ukupne vrijednosti vibracija i nave-

dene vrijednosti emisije buke mogu se koristiti

i za uvodnu procjenu opterećenja.

UPOZORENJE!

► Emisije vibracija i buke mogu tijekom stvar-

nog korištenja električnog alata odstupati od

navedenih vrijednosti ovisno o načinu upora-

be električnog alata, a posebno ovisno o vrsti

izratka.

► Pokušajte opterećenje zadržati na što nižoj

razini. Primjeri mjera za smanjenje optereće-

nja vibracijama su nošenje rukavica prilikom

uporabe uređaja i ograničenje radnog vre-

mena. Pritom morate uzeti u obzir sve dijelo-

ve ciklusa pogona (primjerice razdoblja u ko-

jima je električni uređaji isključen, kao i

razdoblja u kojima je uređaj uključen ali radi

bez opterećenja).

Opće sigurnosne

napomene za uporabu

električnog alata

UPOZORENJE!

► Pročitajte sve sigurnosne napomene, upute,

slike i tehničke podatke koji se nalaze uz

ovaj električni alat. Nepridržavanje sljede-

ćih uputa može uzrokovati strujni udar, požar

i/ili teške ozljede.

Sačuvajte sve sigurnosne napomene i upute

za buduću uporabu.

Pojam „električni alat“ koji se koristi u sigurnosnim

napomenama odnosi se na električni alat s mrežnim

napajanjem (s mrežnim kabelom) i na električni

alat s pogonom na baterije (bez mrežnog kabela).

IB_339111_PDSSA20-LiA1_LB7.indb 15 18.03.20 12:18

PDSSA 20-Li A1

■ 16

│

HR

1. Sigurnost na radnom mjestu

a) Radno mjesto držite čistim i dobro osvijetlje-

nim. Neuredno i neosvijetljeno radno mjesto

može uzrokovati nezgode.

b) Električni alat ne koristite u eksplozivnom

okruženju u kojem se nalaze zapaljive tekući-

ne, plinovi ili prašina. Električni uređaji stvaraju

iskre koje mogu zapaliti prašinu ili pare.

c) Djecu i druge osobe držite podalje tijekom

korištenja električnog alata. U slučaju nepa-

žnje možete izgubiti kontrolu nad električnim

alatom.

2. Električna sigurnost

a) Priključni utikač električnog alata mora

pristajati u utičnicu. Utikač se ni na koji način

ne smije mijenjati. Ne koristite adapterske

utikače s uzemljenim električnim alatom.

Neizmijenjeni utikači iodgovarajuće utičnice

umanjuju rizik od strujnog udara.

b) Izbjegavajte tjelesni kontakt s uzemljenim

površinama kao što su cijevi, sustavi grijanja,

štednjaci ili hladnjaci. Rizik od strujnog udara

veći je kada je tijelo uzemljeno.

c) Električni alat zaštitite od kiše i vlage. Prodi-

ranje vode u električni uređaj povećava rizik

odstrujnog udara.

d) Priključni kabel ne koristite za druge namjene,

primjerice za nošenje električnog alata,

vješanje istog ili izvlačenje utikača iz utičnice.

Priključni kabel držite podalje od izvora topli-

ne, ulja, oštrih bridova i pokretnih dijelova.

Oštećeni ili zapetljani priključni kabeli poveća-

vaju rizik od strujnog udara.

e) Ako električni alat koristite na otvorenom,

koristite samo produžne kabele koji su odo-

breni za uporabu na otvorenom. Uporaba

takve vrste produžnog kabela prikladnog za

uporabu na otvorenom umanjuje rizik od struj-

nog udara.

f) Ako nije moguće izbjeći uporabu električnog

alata u vlažnom okruženju, koristite ﬁdo

sklopku. Korištenje ﬁdo sklopke smanjuje rizik

od strujnog udara.

■ OPREZ

UPOZORENJE:

Mogućnost strujnog udara! Ne otvarati kućište

proizvoda!

3. Sigurnost osoba

a) Budite pažljivi i pazite na ono što radite, i

električnim alatom rukujte razumno. Električni

alat ne koristite ako ste umorni ili pod utjeca-

jem droga, alkohola ili lijekova. Samo jedan

trenutak nepažnje za vrijeme uporabe električ-

nog alata može dovesti do ozbiljnih ozljeda.

b) N

osite osobnu zaštitnu opremu i uvijek nosite

zaštitne naočale.Nošenje osobne zaštitne opre-

me kao što je maska protiv prašine, nošenje

sigurnosnih cipela s potplatima koji ne klize,

zaštitnih rukavica, zaštitne kacige ili zaštite za

sluh – ovisno o vrsti i namjeni električnog alata

– umanjuje rizik od ozljeda.

c) Izbjegavajte nehotično uključivanje uređaja.

Uvjerite se da je električni alat isključen prije

nego ga priključite na napajanje i/ili bateriju,

uhvatite ili nosite. Ako prilikom nošenja električ-

nog alata prst držite na prekidaču ili priključite

napajanje uključenog uređaja, može doći do

nezgode.

d) Alat za podešavanje ili ključeve za matice

uklonite prije uključivanja električnog alata.

Alat ili ključ koji se nalazi u rotirajućem dijelu

električnog alata mogu uzrokovati ozljede.

e) Izbjegavajte neprirodan položaj tijela. Pobrini-

te se da čvrsto stojite i održavajte ravnotežu

u svakom trenutku. Na taj ćete način moći

bolje kontrolirati električni alat u neočekivanim

situacijama.

f) Nosite prikladnu odjeću. Ne nosite široku

odjeću ili nakit. Kosu i odjeću držite podalje

od pokretnih dijelova. Pokretni dijelovi mogu

zahvatiti ležernu, široku odjeću, nakit ili kosu.

g) Ako je moguće montirati usisivač i sustav za

prihvat prašine, morate ih priključiti i ispravno

koristiti. Uporaba usisivača može smanjiti ugro-

ženost prašinom.

IB_339111_PDSSA20-LiA1_LB7.indb 16 18.03.20 12:18

Pagina se încarcă ...

Parkside PDSSA 20-Li A1 Translation Of The Original Instructions

Acest manual este potrivit și pentru

Parkside PDSSA 20-Li A1 Translation Of The Original Instructions

Lucrări conexe

Alte documente