Ubiquiti UniFi UVC-G3-Flex Ghid de inițiere rapidă

Marca: Ubiquiti

Model: UniFi UVC-G3-Flex

Categorie: Accesorii camere de securitate

Tip: Ghid de inițiere rapidă

1080p Indoor/Outdoor IP Camera with

Infrared and 802.3af Support

Model: UVC-G3-Flex

Package Contents

G3 Flex Camera Base Mount Pole/Wall

Mount

Outdoor

Cover

Security Screw

(Qty. 1)

Screws

(Qty. 3)

Screw Anchors

(Qty. 3)

Zip Ties

(Qty. 2)

Installation Requirements

• Phillips screwdriver

• Drill and 6 mm (1/4") bit for drywall anchors and 3 mm (1/8")

for screws)

• Category 5e (or above) Ethernet cable

Note:

When using the Outdoor Cover, use an Ethernetcable

without a strain-relief boot on the connector. This willprevent

unnecessary tension on the cable ends during installation.

Cable without a strain-relief boot Cable with a strain-relief boot

Outdoor Installation Requirements

IMPORTANT: When installed outdoors, the camera must be

installed in the upright postion only.

• Mount the camera in the upright position only. Please see

diagram below.

• Shielded Category 5e (or above) cabling with drain wire

should be used for all outdoor wired Ethernet connections

and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit ui.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH‑SP‑G2, one near the UVC‑G3‑Flex and the other

at the entry point to the building. The ETH‑SP‑G2 will absorb

power surges and safely discharge them into the ground.

To LAN

ETH-SP-G2

US-8-150W

UVC-G3-Flex

Diagram Showing Use of Ethernet Surge Protectors

Before You Begin

The UVC G3 Flex camera is designed to work with Ubiquiti's

new integrated management system, UniFi Protect.

UniFi Protect is a flexible and powerful IP video surveillance

system that can manage UniFi Protect cameras and the UniFi

Protect mobile app. The software is free from all hosting and

licensing fees and comes pre‑installed on UniFi's Cloud Key Gen2

Plus, model UCK‑G2‑PLUS.

UniFi Cloud Key Gen2 Plus, model UCK-G2-PLUS

For more information on UniFi Protect, visit us on the web at:

unifi-protect.ui.com

Note: The UVC G3 Flex camera will also work with the

UniFi Video® 3 controller software.

UniFi Video may be hosted on any of the following:

• UniFi Application Server, model UAS‑XG

• UniFi NVR, model UVC‑NVR‑2TB

• A Linux or Windows computer

UniFi Application Server, model UAS-XG UniFi NVR, model UVC-NVR-2TB

Note: The latest UniFi Video 3 software, for Linux‑ or

Windows‑based computers, is available for free

download at: ui.com/download/unifivideo

Hardware Overview

Microphone

Camera Lens

Light Sensor

LED

Swivel Base

Microphone Microphone for recording audio

Camera Lens Lens for viewing/recording video

Light Sensor Sensor for ambient light detection

LED Status indicator for the following:

LED State Status

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Steady Blue Connected to Controller;

Reset Button Pressed

Flashing Green Disconnected from Controller

Steady White Awaiting adoption

Swivel Base Allows you to change the viewing angle of the

camera by adjusting left or right. Useful if mounted on a wall

or other permanent surface.

Bottom View

Ethernet Port

Reset Button

Ethernet Port The Ethernet Port is a 10/100 Mbps port used

to supply power from a PoE 802.3af‑compliant switch to the

camera. The switch should be connected to a LAN running

DHCP services and the UniFi Video Controller software.

Reset Button The Reset Button is used to reset the camera to

factory defaults. Press and hold the Reset Button for more than

10 seconds while the camera is powered on.

Mounting Options

Use the Base Mount by itself to install the G3 Flex

camera on a desktop or tabletop. Out of the box,

this mount comes preinstalled on the camera.

Use the Base Mount with two screws to install the

G3 Flex camera on a wall (vertically).

Use the Base Mount with two screws to install

the G3 Flex camera on a solid horizontal surface

or ceiling.

Use the Pole Mount with two screws and the

Outdoor Cover to install the G3 Flex camera on a

wall or at surface outdoors. The Outdoor Cover is

not required for indoor installations.

Use the Pole Mount with two plastic zip ties and

the Outdoor Cover to install the G3 Flex camera

on an outdoor pole. The Outdoor Cover is not

required for indoor pole installations.

Additional Mounts Available

There are two additional mounts available for the G3 Flex: a

Ceiling Mount and a Pendant Mount. Each is sold separately.

Use the optional Ceiling Mount, Screw Kit, and

Mount Cover to install the G3 Flex camera on a

solid horizontal surface or ceiling.

Use the optional Ceiling Mount, Mount Cover, and

Back Plate Assembly to install the G3 Flex camera

on a drop tile ceiling or horizontal surface

where the interior side of the Ceiling Mount is

accessible.

Use the Pendant Mount to install the G3 Flex

camera onto a tted 3/4" or 1.5" conduit mount

or ceiling pipe.

Installation

The UVC G3 Flex can be installed using one of the following

methods:

• Desktop For installing on a flat surface such as a desktop

or table/shelf; could be set up for temporary installations.

• Wall/Ceiling For installing in a secure location; used more

for stationary or permanent installations.

• Pole For installing on a pole (indoor or outdoor).

Proceed to the appropriate section for your installation.

Note: The viewing angle or surveillance coverage of the

G3 Flex camera can be changed at any time.

• Tilt the lens up or down for vertical adjustment

• Turn the base left or right for horizontal adjustment

Desktop

1. Remove the Base Mount from the base of the camera.

2. Insert one end of the RJ‑45 cable into the Ethernet Port and the

other end into a PoE 802.3af‑compliant switch.

3. Attach the camera to the Base Mount by lining up the

notches with the slots in the base of the camera. Press

firmly together until the camera is secure.

Note: Ensure the Ethernet cable is seated in the notch

between the Base Mount and base of the camera.

4. Place the camera on a desk or table in its upright position.

5. Adjust the viewing angle or surveillance coverage as

needed by following these steps:

• Tilt the lens up or down to adjust the angle vertically

• Turn the camera body left or right to adjust the angle

horizontally

Installation complete.

Desktop / Table Install

Wall/Ceiling

1. If the Ethernet cable is coming from the inside of a wall:

a. Drill or cut a hole in the wall and feed the Ethernet

cable through the opening.

b. Pull the Ethernet cable forward and slide it through the

opening in the mount.

2. Use the Screws and Screw Anchors to secure the Base Mount

to the wall.

Top Side Down Mounting

Vertical Upright Mounting

3. Connect the Ethernet cable to the Ethernet Port in the base

of the camera.

4. Attach the camera to the Base Mount by lining up the

notches with the slots in the base of the camera. Press

firmly together until the camera is secure.

Vertical mounting on ceiling

Vertical mounting on a wall

Installation complete.

Horizozntal Surface / Ceiling with Base Mount

Indoor Wall with Base Mount

Pole

Note: If you are mounting the camera outdoors, it must

be installed in the upright position to prevent water

from getting into the base of the camera. Use the

OutdoorCover for additional protection from moisture.

1. Attach the Pole Mount to a pole using the included Zip Ties.

2. Insert and pull an Ethernet cable through the back port

opening of the Outdoor Cover.

Note: When using the Outdoor Cover, use an Ethernet

cable without strain‑relief boots on the connector. This

will prevent unnecessary tension on the cable ends.

3. Connect the Ethernet cable to the Ethernet Port on the

G3 Flex camera.

4. Attach the camera to the Outdoor Cover by lining up the

notches with the slots on the bottom of the camera. Press

firmly until the camera snaps on.

5. Attach the camera to the Pole Mount:

a. Press the camera against the Pole Mount and line up

the notches on the mount with the slots on the

bottom of the camera.

b. Slide the camera down onto the Pole Mount until it

is secure.

Note: When using the Outdoor Cover, use an Ethernet

cable without strain‑relief boots on the connector. This

will prevent unnecessary tension on the cable ends.

6. Use a phillips screwdriver to install the Security Screw

through the Outdoor Cover and into the base of the

camera. This secures the camera to the mount.

7. Adjust the camera to the desired viewing angle by:

• Tilting the lens up or down for vertical adjustment

• Turn the camera body left or right to adjust the angle

horizontally

Installation is complete.

Pole Mount Install

Setting Up UniFi Protect via App

Download and install the UniFi Protect app to configure the

UVC‑G3‑Flex.

Note: When you first launch UniFi Protect, the app will

prompt you to enable Bluetooth and other relevant

features necessary to provide the best user experience

possible. Please allow these features and permissions

to take place for proper app functionality.

1. Launch the UniFi Protect app.

2. Tap the side menu in the upper‑left corner of the app to

access additional options.

3. Tap Add Cameras to add a new camera.

Note: If setting up multiple cameras, UniFi Protect

allows you to add more than one camera during the

setup process.

4. When the Select cameras screen appears, tap each camera

in the list you would like to add to your UniFi Protect

system. Tap Set up cameras to continue.

5. A Name your camera screen appears individually for each

camera you selected in step 4. Enter a name for each

camera and tap Next, repeating this process until all

cameras have been named.

6. If necessary, any camera requiring a firmware upgrade will

update at this time. Once completed, a live view of each

camera will display in the app.

UVC G3 FLEX

Specifications

UVC‑G3‑Flex

Dimensions Ø 107.5 x 48 x 48 mm

(Ø 4.23 x 1.89 x 1.89")

Weight

170 g (5.99 oz)

Sensor 1/2.7" 2‑Megapixel HDR Sensor

Lens EFL 4mm / f2.0

Viewing Angle with Lens

Distortion Correction (LDC)

LDC Off

LDC On

87.4° (H), 47° (V), 104° (D)

80° (H), 46° (V), 92° (D)

Night Mode IR LEDs with Mechanical ICR Filter

Video Compression H.264

Resolution 1080p FHD (1920 x 1080)

Maximum Frame Rate 25 FPS

Image Settings Brightness, Contrast, Sharpness, Saturation,

Noise Reduction, 50/60 Hz

Microphone

Yes

Management Interface UniFi Protect; UniFi Video

Networking Interface (1) 10/100 Ethernet Port

Max. Power Consumption 4W

Power Method 802.3af PoE

Power Supply 802.3af PoE Switch Port

Mounting Table, Wall (Indoor/Outdoor), Pole

Operating Temperature ‑20 to 50° C

(‑4 to 122° F)

Operating Humidity 20 to 90% Noncondensing

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Hot Surface. Do not touch.

WARNING: Do not use this product in a location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Pagina se încarcă ...

Ubiquiti UniFi UVC-G3-Flex Ghid de inițiere rapidă

Marca: Ubiquiti

Model: UniFi UVC-G3-Flex

Categorie: Accesorii camere de securitate

Tip: Ghid de inițiere rapidă

Descărcați PDF

raport

în alte limbi

English: Ubiquiti UniFi UVC-G3-Flex Quick start guide
italiano: Ubiquiti UniFi UVC-G3-Flex Guida Rapida

Ubiquiti UniFi UVC-G3-Flex Ghid de inițiere rapidă

Ubiquiti UniFi UVC-G3-Flex Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente