Ubiquiti NBE-M5-400 NanoBeam M Ghid de inițiere rapidă

Marca: Ubiquiti

Model: NBE-M5-400 NanoBeam M

Tip: Ghid de inițiere rapidă

Acest manual este potrivit și pentru

NBE-M2-400 NanoBeam M

High-Performance

Integrated InnerFeed

™

airMAX

Bridge

Models:

NBE-M2-400, NBE-M5-400

High-Performance

egrated Inne

High-Performance

Integrated InnerFeed

High-Performance

ated Inne

Introduction

Thank you for purchasing the Ubiquiti Networks

™

NanoBeam

™

This Quick Start Guide is designed to guide you through

the installation, and show you how to access the airOS®

Configuration Interface. This Quick Start Guide also includes the

warranty terms and is for use with the

NanoBeamM2, model

NBE-M2-400, and the NanoBeamM5, model NBE-M5-400.

If you want to add a radome to enclose the Dish Reflector,

8ELTXLWL1HWZRUNV©RIIHUV©WKH©1DQR%HDP©5DGRPH©©PP©

PRGHO1%(õ5$'õ©DV©DQ©RSWLRQDO©DFFHVVRU\©3URGXFW©GHWDLOV©DUH©

available on our website at www.ubnt.com/airmax

3DFNDJH©&RQWHQWV

Dish Reflector NBE-M2-400

$QWHQQD©)HHG

NBE-M5-400

$QWHQQD©)HHG

Rear Housing Dish Bracket 3ROH©&ODPS U-Bolt

High-Performance

airMAX

Bridge

Models:

NBE-M2-400, NBE-M5-400

High-Performance

)ODQJH©1XWV

(M8, Qty. 2)

3R(©$GDSWHU

9©$

3RZHU©&RUG Quick Start Guide

* The NBE-M5-400 Antenna Feed has a thin gray ring around the center of

the cap to differentiate it from the NBE-M5-300 Antenna Feed.

7(506©2)©86(©8ELTXLWL©UDGLR©GHYLFHV©PXVW©EH©SURIHVVLRQDOO\©LQVWDOOHG©6KLHOGHG©(WKHUQHW©

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

)UHTXHQF\©6HOHFWLRQ©')6©UHTXLUHPHQWV

Hardware Overview

Bottom View

Cable Door

Rear Housing

Technology

Ethernet Port

Release

Button Slot

Dish Bracket

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Antenna Feed

Antenna Feed The NanoBeamM2 Antenna Feed is shown;

however, the NanoBeamM5 Antenna Feed has the same layout

for the Ethernet Port, Reset button, and Release button.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBeam is

DOUHDG\©SRZHUHGRQ

Release Button $IWHU©\RX©DVVHPEOH©WKH©1DQR%HDP©FKHFN©WKH©

Release button; it should be fully engaged in the Release Button

Slot of the Rear Housing. This ensures that the Antenna Feed is

locked into place. If you need to remove the Antenna Feed, you

must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

GHIDXOW©YDOXHV©DUH©VKRZQ©EHORZ

LED will light green when the wireless signal

strength is above -65 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light red when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Power 7KH©3RZHU©/('©ZLOO©OLJKW©JUHHQ©ZKHQ©WKH©

device is connected to a power source.

$SSOLFDWLRQ©([DPSOHV

The NanoBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The NanoBeam mounted outdoors without the Dish Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm or ½" wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

WKURXJK©WKH©$&©JURXQG©RI©WKH©3R(

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

1HWZRUNV©)RU©PRUH©GHWDLOV©YLVLW©www.ubnt.com/toughcable

Installation

The installation instructions show the NanoBeamM2; however,

the same instructions apply to the NanoBeamM5.

1. $OLJQ©DQG©LQVHUW©WKH©WDEV©RI©WKH©Dish Bracket into the

slots of the Dish Reflector. Rotate the Dish Bracket

counter-clockwise until the tabs lock into place.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Bracket. Insert the pins and

SXVK©XQWLO©WKH\©ORFN©LQWRSODFH

*720-00004-01*

720-00004-01

3. 3XVK©LQ©WKH©VLGHV©RI©WKH©Cable Door and detach it from the

Rear Housing.

4. $WWDFK©WKH©Antenna Feed

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

5. &RQQHFW©WKH©(WKHUQHW©FDEOH

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

6. Slide the Pole Clamp onto the Dish Bracket.

7. Insert the U-Bolt into the Pole Clamp and Dish Bracket. Secure

each end of the U-Bolt with a Flange Nut.

25 N-m

(18 lb-ft)

1RWH The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

8. 2SWLRQDO©,I©\RX©KDYH©WKH©NanoBeam Radome (optional

accessory), then align the arrows on the bottoms of the

Radome and Dish Reflector so the Drain Holes on the Radome

point downward. Snap the Radome onto the Dish Reflector.

9. Connect the other end of the Ethernet cable from the

NanoBeam to the Ethernet port labeled POE on the

3R($GDSWHU.

10. &RQQHFW©DQ©(WKHUQHW©FDEOH©IURP©\RXU©/$1©RU©FRPSXWHU©WR©

the Ethernet port labeled LAN on the PoE Adapter.

11. Connect the Power Cord to the power port on the PoE

Adapter. Connect the other end of the Power Cord to a

power outlet.

$FFHVVLQJ©DLU26

Verify connectivity in the airOS Configuration Interface.

1. Make sure that your host machine is connected via

Ethernet to the NanoBeam.

2. Configure the Ethernet adapter on your host system with a

VWDWLF©,3©DGGUHVV©RQ©WKH©[©VXEQHW

3. Launch your web browser and type https://192.168.1.20

LQ©WKH©DGGUHVV©ILHOG©3UHVV©enter©3&©RU©return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

1RWH U.S. product versions are locked to the

U.S. Country Code to ensure compliance with

)&&UHJXODWLRQV©

5. Select the NanoBeam Dish Reflector©VL]H

a. Click the Wireless tab.

b. )rom the Antenna drop-down list, select the

appropriate option.

c. Click Change to save.

d. Click OK to confirm.

Customize additional settings as needed to complete

WKH©FRQILJXUDWLRQ©)RU©DGGLWLRQDO©GHWDLOV©RQ©WKH©DLU26©

Configuration Interface, refer to the User Guide available at

documentation.ubnt.com/airmax

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer's responsibility to make sure the device is

operated within local country regulatory requirements.

Since Ubiquiti Networks equipment can be paired with a

variety of antennas and cables, the Antenna and Output Power

fields are provided to the professional installer to assist in

meeting regulatory requirements.

Specifications

NanoBeam

Dimensions

NBE-M2-400

NBE-M5-400

©[©©[©©PP©0RXQW©,QFOXGHG

©[©©[©©PP©0RXQW©,QFOXGHG

Weight

NBE-M2-400

NBE-M5-400

1.795 kg (Mount Included)

1.753 kg (Mount Included)

2SHUDWLQJ©)UHTXHQF\

NBE-M2-400

NBE-M5-400

2405 - 2475 MHz

:RUOGZLGH©©õ©©0+]

86$©©õ©©0+]

Gain

NBE-M2-400

NBE-M5-400

18 dBi

25 dBi

Networking Interface

NBE-M2-400

NBE-M5-400

©©(WKHUQHW©3RUW

©©(WKHUQHW©3RUW

Enclosure 2XWGRRU©89©6WDELOL]HG©3ODVWLF

0D[©3RZHU©&RQVXPSWLRQ

NBE-M2-400

NBE-M5-400

6 W

8 W

3RZHU©6XSSO\ 9©$©3R(©6XSSO\©,QFOXGHG

3RZHU©0HWKRG 3DVVLYH©3R(©3DLUV©©©©5HWXUQ

Wind Survivability 125 mph

Wind Loading 77 lbf @ 125 mph

&HUWL½FDWLRQV &(©)&&©,&

Mounting 3ROH©0RXQWLQJ©.LW©,QFOXGHG

Operating Temperature -40 to 70° C

Operating Humidity 5 to 95% Condensing

Shock and Vibrations ETSI300-019-1.4

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

:$51,1* Do not use this product in location that can

be submerged by water.

:$51,1*©$YRLG©XVLQJ©WKLV©SURGXFW©GXULQJ©DQ©HOHFWULFDO©

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. 3URWHFWLYH©HDUWKLQJ©LV©SURYLGHG©E\©/LVWHG©$&©DGDSWHU©%XLOGLQJ©

installation shall provide appropriate short-circuit backup

protection.

e. 3URWHFWLYH©ERQGLQJ©PXVW©EH©LQVWDOOHG©LQ©DFFRUGDQFH©ZLWK©ORFDO©

national wiring rules and regulations.

Limited Warranty

8%,48,7,©1(7:25.6©,QF©±8%,48,7,©1(7:25.6²©ZDUUDQWV©WKDW©WKH©

SURGXFWV©IXUQLVKHG©KHUHXQGHU©WKH©±3URGXFWV²©VKDOO©EH©IUHH©IURP©GHIHFWV©

in material and workmanship for a period of one (1) year from the date

RI©VKLSPHQW©E\©8%,48,7,©1(7:25.6©XQGHU©QRUPDO©XVH©DQG©RSHUDWLRQ©

8%,48,7,©1(7:25.6´©VROH©DQG©H[FOXVLYH©REOLJDWLRQ©DQG©OLDELOLW\©XQGHU©

WKH©IRUHJRLQJ©ZDUUDQW\©VKDOO©EH©IRU©8%,48,7,©1(7:25.6©DW©LWV©GLVFUHWLRQ©

WR©UHSDLU©RU©UHSODFH©DQ\©3URGXFW©WKDW©IDLOV©WR©FRQIRUP©WR©WKH©DERYH©

ZDUUDQW\©GXULQJ©WKH©DERYH©ZDUUDQW\©SHULRG©7KH©H[SHQVH©RI©UHPRYDO©DQG©

UHLQVWDOODWLRQ©RI©DQ\©3URGXFW©LV©QRW©LQFOXGHG©LQ©WKLV©ZDUUDQW\©7KH©ZDUUDQW\©

SHULRG©RI©DQ\©UHSDLUHG©RU©UHSODFHG©3URGXFW©VKDOO©QRW©H[WHQG©EH\RQG©LWV©

original term.

Warranty Conditions

7KH©DERYH©ZDUUDQW\©GRHV©QRW©DSSO\©LI©WKH©3URGXFW

(I) has been modified and/or altered, or an addition made thereto,

H[FHSW©E\©8ELTXLWL©1HWZRUNV©RU©8ELTXLWL©1HWZRUNV´©DXWKRUL]HG©

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware; or

(VI) KDV©QR©RULJLQDO©8ELTXLWL©0$&©ODEHO©RU©LV©PLVVLQJ©DQ\©RWKHU©RULJLQDO©

Ubiquiti label(s).

(VII) has not been received by Ubiquiti within 30 days of issuance of

WKH©50$

,Q©DGGLWLRQ©WKH©DERYH©ZDUUDQW\©VKDOO©DSSO\©RQO\©LI©WKH©SURGXFW©KDV©EHHQ©

properly installed and used at all times in accordance, and in all material

UHVSHFWV©ZLWK©WKH©DSSOLFDEOH©3URGXFW©GRFXPHQWDWLRQ©DOO©(WKHUQHW©FDEOLQJ©

UXQV©XVH©&$7©RU©DERYH©DQG©IRU©RXWGRRU©LQVWDOODWLRQV©VKLHOGHG©(WKHUQHW©

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

1R©3URGXFWV©ZLOO©EH©DFFHSWHG©IRU©UHSODFHPHQW©RU©UHSDLU©ZLWKRXW©REWDLQLQJ©

D©5HWXUQ©0DWHULDOV©$XWKRUL]DWLRQ©50$©QXPEHU©IURP©8%,48,7,©1(7:25.6©

GXULQJ©WKH©ZDUUDQW\©SHULRG©DQG©WKH©3URGXFWV©EHLQJ©UHFHLYHG©DW©8%,48,7,©

1(7:25.6´©IDFLOLW\©IUHLJKW©SUHSDLG©LQ©DFFRUGDQFH©ZLWK©WKH©50$©SURFHVV©RI©

8%,48,7,©1(7:25.6©3URGXFWV©UHWXUQHG©ZLWKRXW©DQ©50$©QXPEHU©ZLOO©QRW©

be processed and will be returned freight collect or subject to disposal.

,QIRUPDWLRQ©RQ©WKH©50$©SURFHVV©DQG©REWDLQLQJ©DQ©50$©QXPEHU©FDQ©EH©

IRXQG©DW©www.ubnt.com/support/warranty.

Disclaimer

(;&(37©)25©$1<©(;35(66©:$55$17,(6©3529,'('©+(5(,1©8%,48,7,©

1(7:25.6©,76©$)),/,$7(6©$1'©,76©$1'©7+(,5©7+,5'©3$57<©'$7$©

6(59,&(©62)7:$5(©$1'©+$5':$5(©3529,'(56©+(5(%<©',6&/$,0©

$1'©0$.(©12©27+(5©5(35(6(17$7,21©25©:$55$17<©2)©$1<©.,1'©

(;35(66©,03/,('©25©67$78725<©,1&/8',1*©%87©127©/,0,7('©72©

5(35(6(17$7,216©*8$5$17((6©25©:$55$17,(6©2)©0(5&+$17$%,/,7<©

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

Limitation of Liability

68&+©'$0$*(6©

Note

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

Convention on Contracts for the International Sale of Goods shall not apply

Compliance

)&&

for compliance could void the user’s authority to operate the equipment.

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

Industry Canada

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Canada.

d’antenne et son gain doivent être choisies de façon que la puissance

pour une communication réussie.

VXLYDQWHV

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

The antennas used for this transmitter must be installed to provide a

separation distance of at least 113 cm from all persons and must not be located

or operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou

transmetteur.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

must follow the CE marking.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

XQG©HOHNWURQLVFKH©*HUlWH©EHU©GLH©GDIU©]XVWlQGLJHQ©XQG©YRQ©GHU©

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

SRWHQWLHOOH©QHJDWLYH©)ROJHQ©IU©8PZHOW©XQG©GLH©PHQVFKOLFKH©*HVXQGKHLW©

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

$OWJHUlWH©EHQ|WLJHQ©ZHQGHQ©6LH©VLFK©ELWWH©DQ©GLH©|UWOLFKHQ©%HK|UGHQ©RGHU©

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

3URGXNW©HUZRUEHQ©KDEHQ

Pagina se încarcă ...

Ubiquiti NBE-M5-400 NanoBeam M Ghid de inițiere rapidă

Marca: Ubiquiti

Model: NBE-M5-400 NanoBeam M

Tip: Ghid de inițiere rapidă

Acest manual este potrivit și pentru

NBE-M2-400 NanoBeam M

Descărcați PDF

raport

în alte limbi

English: Ubiquiti NBE-M5-400 NanoBeam M Quick start guide
italiano: Ubiquiti NBE-M5-400 NanoBeam M Guida Rapida

Ubiquiti NBE-M5-400 NanoBeam M Ghid de inițiere rapidă

Acest manual este potrivit și pentru

Ubiquiti NBE-M5-400 NanoBeam M Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente