Whirlpool AKR 957 IX WP Program Chart

Marca: Whirlpool

Model: AKR 957 IX WP

Categorie: Hote pentru aragaz

Tip: Program Chart



5019 318 33097

AKR 957

KARTA INSTALACYJNA

Minimalna odległość od palników: 50 cm (palniki elektryczne), 75 cm

(palniki gazowe, olejowe lub węglowe). Podczas montażu należy

przestrzegać kolejności numeracji (

.....). Nie podłączać

urządzenia do zasilania, zanim nie zostanie zakończony całkowicie jego

montaż. Uwaga! Przewód wylotowy oraz kolanka mocujące (15) nie

znajdują się na wyposażeniu i należy je dokupić.

POPIS INSTALACE

Minimální vzdálenost od sporáků: 50 cm (elektrické sporáky), 75 cm

(sporáky na plyn, naftu nebo uhlí). Při montáži sledujte číslování

(

.....). Spotřebič připojte k elektrické síti až po úplném dokončení

instalace. Upozornění! Nasávací trubka a upevňovací pásky (15) nejsou

součástí vybavení a musíte je zakoupit.

INŠTALAČNÁ SCHÉMA

Minimálna vzdialenost' od sporáka: 50 cm (elektrické sporáky), 75 cm

(plynové sporáky, sporáky na naftu alebo uhlie). Pri montáži postupujte

podľa číslic (

.....). Spotrebič nezapájajte do siete, kým nie je

inštalácia úplne ukončená. Upozornenie! Rúra na odvádzanie dymov a

upevňovacie svorky (15) sa nedodávajú, musíte ich kúpit' samostatne.

ÜZEMBE HELYEZÉSI ÚTMUTATÓ

A tűzhelytől való minimális távolság: 50 cm (elektromos tűzhely), 75 cm

(gáz-, olaj- vagy széntüzelésű tűzhely). A felszereléshez kövesse a

számozást (

.....). A készüléket csak akkor szabad áram alá

helyezni, ha a beüzemelés már megtörtént. Figyelem! Az elvezető cső és

a rögzítőpántok (15) nem tartozékok, így azokat külön meg kell vásárolni.

СХЕМА УСТАНОВКИ

lМинимальное расстояние до конфорок: 50 см (электрические

конфорки), 75 см (газовые, керосиновые или угольные).

Последовательность действий при монтаже должна

соответствовать нумерации (

.....). Не подключайте

прибор к сети до тех пор, пока его установка не будет полностью

закончена. Внимание! Выпускная труба и крепежные зажимы (15)

не входят в комплект поставки и приобретаются отдельно.

КАРТА ЗА ИНСТАЛИРАНЕ

Минимално разстояние от печки: 50 см (електрически печки),

75 см (печки с газ, нафта или въглища). За монтаж следвайте

номерацията (

.....). Не включвайте захранването на уреда,

докато инсталирането не е завършено докрай. Внимание! Тръбата

за отвеждане не е предоставена и трябва да се закупи отделно.

FIȘA DE INSTALARE

Distanţa minimă de la arzătoare: 50 cm (arzătoare electrice), 75 cm (arzătoare

pe bază de gaze, petrol sau cărbune). Pentru montaj urmaţi numerotarea

(

.....). Nu branșaţi aparatul la curent până când nu terminaţi definitiv

operaţia de instalare. Atenţie! Tubul de evacuare și manșoanele de fixare (15)

nu fac parte din dotare și trebuie să fie cumpărate separat.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or coal

cookers). To install, follow points (1

.....). Do not connect the appliance to

the electrical power supply until installation is completed. Warning! The exhaust pipe

and clamps (15) are not supplied and must be bought separately.

RUS

31833097.fm Page 1 Tuesday, November 11, 2003 12:45 PM



5019 318 33097

AKR 957

17b

4-13

17a

4 x 4x8

4 x 3,5x9,5

2 x

2,9x6,5

31833097.fm Page 2 Tuesday, November 11, 2003 12:45 PM



5019 318 33097

AKR 957

PL SK H RUS

BG RO GB

INSTALLATION - ASSEMBLY INSTRUCTIONS

Preliminary information for installing the hood

Disconnect the power supply at the domestic main switch before carrying out electrical connections.

Remove the grease filter/s.

Pre-assemble the three parts of the flue support bracket with 4 screws. The width

of the bracket

must be

identical to the internal width of the telescopic flue.

Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.

Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the

centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the

hood: remember that with installation completed the bottom of the hood must be at least 50 cm above

the cooktop in case of electric cookers and 75 cm in case of gas or mixed cookers.

Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two

external holes and drill, remove the hole diagram, insert 2 wall plugs and fix the hood support bracket

with two 5x45 mm screws.

Hook the hood to the bracket.

Adjust the distance between the hood and the wall.

Adjust the hood horizontally.

From the inside of the extraction unit, mark the holes for fixing the hood.

Remove the hood from the bracket.

Drill on the marks (Ø 8 mm - see step 10)

10.

Insert 2 wall plugs.

11.

Fit the flue support bracket

to the wall and against the ceiling, use the support bracket as hole diagram

(the small slot on the support must match the line drawn on the wall - step 4) and mark 2 holes with the

pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.

12.

Fix the flue support bracket to the wall with two 5x45 mm screws.

13.

Hook the hood to the bottom bracket.

14.

Fix the hood to the wall with two 5x45 mm screws (ABSOLUTELY NECESSARY).

15.

Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar

located above the extraction motor unit.

For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter

operation, fix the deflector

to the flue support bracket

and connect the other end of the exhaust pipe

to the deflector collar

. Once the steam and fumes have been filtered by the carbon filter (not provided,

to be ordered separately) they are conveyed back to the kitchen through grid

16.

Carry out the electrical connection.

17.

Apply the flues and fix them with 2 screws (

20a

) to the flue support

(

20b

18.

Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction

unit.

Refit the grease filter/s and check for correct hood operation.

31833097.fm Page 24 Tuesday, November 11, 2003 12:45 PM



5019 318 33097

AKR 957

PL SK H RUS

BG RO GB

CONTROL PANEL

Control panel calibration

When the appliance is plugged in (or after a power failure) the system calibrates the buttons; during

calibration two blinking dots will appear.

The calibration lasts for 15''.

At the end of the calibration procedure, the two dots will stop blinking and only the bottom right dot will

stay alight.

button (Stand by) /

OFF

extraction /

Resetfilter saturation

indicator:

(Stand by) - the display shows a lighted dot only.

OFF

- the display is OFF: all controls, except for the light button, are disabled.

To set the hood to

(Stand by) or

OFF

, press the button and wait until the dot appears or disappears

according to the required setting.

Reset filter saturation indicator.

Press and hold for at least 3 seconds, an acoustic signal will sound.

The reset operation can only take place when the hood is on.

Light

ON/OFF

button.

Extraction

speed decrease button

(1, 2, 3, P-intensive).

Extraction

speed increase button

(P-intensive, 3, 2, 1).

Warning!

The intensive extraction speed appears on the left of the display with the letter

and the remaining

operating time in minutes (and the blinking dot) on the right; after 5 minutes, it automatically switches to

extraction speed 2.

Timer

button

: after selecting the required extraction speed, press this button to set the timing:

Extraction speed 1: 20 minutes

Extraction speed 2: 15 minutes

Extraction speed 3: 10 minutes

Intensive extraction speed (

): 5 minutes

The display will show the remaining operating time and the blinking dot on the right.

At the end, the hood will switch off.

Press again to disable the timing.

Display:

shows

the

selected extraction speed

grease filter

(

) or

carbon filter

(

) saturation,

Stand

by mode

(

lighted dot

) and

control panel calibration

(

two blinking dots

Warning!

The carbon filter saturation indicator is normally deactivated

(for extractor version - see

attached instructions manual). In order to activate it (for filter operation - see attached instructions manual),

simultaneously press AND HOLD buttons

and

until

appears on the display. To deactivate the carbon filter

saturation indicator, simultaneously press AND HOLD buttons

and

: letter

will appear on the display,

followed by

. The latter will disappear after a few seconds.

12345

Fig. 1

PRODUCT SHEET

31833097.fm Page 25 Tuesday, November 11, 2003 12:45 PM



5019 318 33097

AKR 957

PL SK H RUS

BG RO GB

Control panel.

Grease filter.

Halogen bulbs.

Steam deflector.

Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

Disconnect the electrical power supply.

Remove the grease filters -

Fig. 2

: push the

spring release handle backwards (

), then

remove the filter downwards (

After cleaning the grease filter, remount in

reverse order ensuring the entire extraction

surface is covered.

Replacing bulbs

Disconnect the electrical power supply.

Use a small screwdriver or any other suitable tool

to prise off (

m-Fig. 2

) the lamp cover (

p-Fig. 2

Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs only,

making sure not to touch them with your hands.

Close the lighting unit (snap-close).

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

Disconnect the electrical power supply.

Remove the grease filter (

f1/f2 - Fig. 2

Turn the side knobs 90° and then remove the

filter holder (

g - Fig. 3

Fit the carbon filter (

h - Fig. 3

) in the filter

holder (

i - Fig. 3

Refit the filter holder and secure it to the hood

by turning the side knobs 90° (

g - Fig. 3

Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible,

using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After

washing, dry the filter in the oven at 100°C for 10

minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Fig. 3

Fig. 2

31833097.fm Page 26 Tuesday, November 11, 2003 12:45 PM

Whirlpool AKR 957 IX WP Program Chart

Marca: Whirlpool

Model: AKR 957 IX WP

Categorie: Hote pentru aragaz

Tip: Program Chart

Descărcați PDF

raport

Whirlpool AKR 957 IX WP Program Chart

Whirlpool AKR 957 IX WP Program Chart

în alte limbi

Lucrări conexe

Alte documente