Whirlpool AKR 951 IX WP Program Chart

Marca: Whirlpool

Model: AKR 951 IX WP

Categorie: Hote pentru aragaz

Tip: Program Chart



5019 318

33094

AKR 951 - AKR 960

KARTA INSTALACYJNA

Minimalna odległość od palników: 50 cm (od palników elektrycznych), 75 cm (od

palników gazowych, olejowych lub węglowych). Podczas montażu należy

przestrzegać kolejności numeracji (

.....) oraz odpowiednich instrukcji.

Nie należy podłączać urządzenia do zasilania zanim nie zakończy się całkowicie

jego montażu.

Uwaga! Rura odprowadzająca dym i parę oraz kolanka nie są dostarczane i należy

je zakupić oddzielnie.

POPIS INSTALACE

Minimální vzdálenost od sporáků: 50 cm (elektrické sporáky), 75 cm (sporáky na

plyn, naftu nebo uhlí). Při montáži sledujte číslování (

.....) a příslušné

pokyny. Spotřebič připojte k elektrické síti až po úplném dokončení instalace.

Upozornění! Nasávací trubka a pásky k upevnění nejsou součástí vybavení,

musíte je zakoupit.

INŠTALAČNÁ SCHÉMA

Minimálna vzdialenost' od sporáka: 50 cm (elektrické sporáky), 75 cm (plynové

sporáky, sporáky na naftu alebo uhlie). Pri montáži postupujte podľa číslic

(

.....) a dodržujte príslušné pokyny. Spotrebič nezapájajte do siete, kým

nie je inštalácia úplne ukončená.

Upozornenie! Rúra na odvádzanie dymov a upevňovacie svorky sa nedodávajú,

musíte ich kúpit' samostatne.

ÜZEMBE HELYEZÉSI ÚTMUTATÓ

A tűzhelytől való minimális távolság: 50 cm (elektromos tűzhely), 75 cm (gáz-,

olaj- vagy széntüzelésű tűzhely). A felszereléshez kövesse a számozást

(

.....) és a vonatkozó utasításokat. Ne helyezze feszültség alá a

készüléket addig, amíg nem történt meg maradéktalanul az üzembe helyezés.

Figyelem! Az elvezető cső és a rögzítőpántok nem tartozékok, így azokat külön

meg kell vásárolni.

СХЕМА УСТАНОВКИ

Минимальное расстояние до конфорок: 50 см (электрические

конфорки), 75 см (газовые, керосиновые или угольные).

Последовательность действий при монтаже должна соответствовать

нумерации (

.....) и приведенным инструкциям. Не подключайте

прибор к сети до тех пор, пока установка не будет полностью

закончена.

Внимание! Выпускная труба и крепежные зажимы не входят в комплект

поставки и приобретаются отдельно.

КАРТА ЗА ИНСТАЛИРАНЕ

Минимално разстояние от печки: 50 см (електрически печки), 75 см

(печки с газ, нафта или въглища). За монтаж следвайте номерацията

(

.....) и съответните инструкции. Не включвайте уреда към

мрежата, докато инсталирането не е завършено докрай.

Внимание! Тръбата за отвеждане не е предоставена и трябва да се

закупи отделно.

FIȘA DE INSTALARE

Distanţa minimă de la arzătoare: 50 cm (arzătoare electrice), 75 cm (arzătoare pe

bază de gaze, motorină sau cărbune). Pentru montare urmaţi numerotarea

(

.....) și instrucţiunile corespunzătoare. Nu branșaţi aparatul la curent

până când nu terminaţi definitiv operaţia de instalare.

Atenţie! Tubul de evacuare și manșoanele de fixare nu fac parte din dotare și

trebuie să fie cumpărate separat.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or coal

cookers). To assemble follow the numbers (1

.....) and relative instructions. Do

not connect the appliance to the electrical power supply until installation is completed.

Warning! The exhaust pipe and clamps are not supplied and must be bought separately.

RUS

31833094.fm Page 1 Wednesday, November 19, 2003 12:24 PM



AKR 951 - AKR 960

5019 318

33094

14,5

273

244

214

190

31833094.fm Page 2 Wednesday, November 19, 2003 12:24 PM



5019 318

33094

AKR 951 - AKR 960

13A

13F

31833094.fm Page 3 Wednesday, November 19, 2003 12:24 PM



AKR 951 - AKR 960

5019 318

33094

31833094.fm Page 4 Wednesday, November 19, 2003 12:24 PM



5019 318

33094

AKR 951 - AKR 960

PL SK H RUS

BG RO GB

Preliminary information for installing the hood:

Expansion plugs are provided to secure the hood to most types of ceilings. A qualified technician is needed,

however, to make sure that the plugs are suitable for your ceiling. The ceiling must be strong enough to take

the weight of the hood.

Disconnect the power supply at the home main switch during electrical connections.

Adjust extension of the hood support structure, as the final height of the hood depends on this, and

remember that with installation completed the hood must be at least 50 cm above the cooktop in case of

electric cookers and 75 cm in case of gas or mixed cookers.

Fix the two sections of the structure using 8 screws.

Place the ceiling hole diagram directly above the cooktop (the centre of the diagram must match the

centre of the cooktop and the edges must be parallel to the sides of the cooktop - the side of the diagram

with the wording FRONT corresponds to the control panel side). Prepare the electrical connection.

Drill as shown (6 holes for 6 wall plugs - 4 plugs for hooking), screw the 4 outer screws leaving a space

of about 1 cm between the screw head and the ceiling.

Fit an exhaust pipe inside the truss and connect it to the collar of the motor compartment (exhaust pipe

and clamps are not provided).

Hook the truss to the 4 screws (see step 4).

CAUTION! The side of the truss with connection box corresponds to the side of the control panel with

hood assembled.

Tighten the 4 screws.

Insert and tighten another 2 screws in the remaining free holes for secure fixing.

Carry out the electrical connection to the mains power supply, only turn on the power supply with

assembly completed.

10.

Hook the hood to the truss, check for perfect hooking - to hook the hood to the truss partially screw 4

screws (also see step 12).

11.

Fixing the hood to the truss with two screws, will also facilitate centering the two parts.

12.

Tighten the 4 screws fixing the truss to the hood.

13.

For extractor operation (

13A

), connect the other end of the exhaust pipe to the home drain device.

For filter operation (

13F

), fit deflector

on the truss and fix it with 4 screws to the special bracket.

Finally, connect the exhaust pipe to the collar located on the deflector.

14.

Fit the nuts with fixing hooks supplied inside the top and bottom sections of the flues at the rectangular

slots. A total of 10 nuts must be fitted.

15.

Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated

on the same side of the control panel and the other on the opposite side.

Screw the two sections with 4 screws (2 each side - see the plan diagram for joining the two sections).

16.

Fix the top flue assembly to the truss, near the ceiling, with two screws (one each side).

17.

Carry out electrical connection of control panel and bulbs.

18.

Join the two bottom sections of the flue covering the truss using 6 screws (3 each side - also see the plan

diagram for joining the two sections).

19.

Insert the bottom section of the flue in the special seat to completely cover the motor compartment and

electrical connection box, and fix the hood with two screws from the inside.

20.

Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION! THE BOTTOM FLUE

TABS ARE THE NARROWER AND SHALLOWER ONES).

The wider and deeper tabs are those used for the top flue, and must be cut to size.

21.

Turn the mains power on again at the central electrical panel and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

31833094.fm Page 19 Wednesday, November 19, 2003 12:24 PM



AKR 951 - AKR 960

5019 318

33094

PL SK H RUS

BG RO GB

Control panel.

Grease filter.

Halogen bulbs.

Steam deflector.

Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

Disconnect the electrical power supply.

Remove the grease filters -

Fig. 1

: pull the spring

release handle

(f)

downwards, then remove the

filter.

After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface

is covered.

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

Disconnect the electrical power supply.

Remove the grease filter

(f - Fig. 1)

Turn the side knobs 90° and then remove the

filter holder

(g - Fig. 2)

Fit the carbon filter

(h - Fig. 2)

in the filter

holder

(i - Fig. 2)

Refit the filter holder and secure it to the hood

with the screw

(g - Fig. 2)

Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible,

using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After

washing, dry the filter in the oven at 100° C for 10

minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Replacing bulbs

Disconnect the electrical power supply.

Use a small screwdriver or any other suitable tool

to prise off

(m-Fig. 3)

the lamp cover

(p-Fig. 3)

Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs only,

making sure not to touch them with your hands.

Close the lighting unit (snap-close).

CONTROL PANEL

Light ON/OFF switch.

ON/OFF and speed 1 selector switch

(small amount of steam and fumes).

B+C.

Speed 2 selector switch

(medium amount of steam and fumes).

B+D.

Speed 3 selector switch

(large amount of steam and fumes).

ABCD

Fig. 1

Fig. 4

Fig. 2

Fig. 3

PRODUCT SHEET

31833094.fm Page 20 Wednesday, November 19, 2003 12:24 PM

Whirlpool AKR 951 IX WP Program Chart

Marca: Whirlpool

Model: AKR 951 IX WP

Categorie: Hote pentru aragaz

Tip: Program Chart

Descărcați PDF

raport

Whirlpool AKR 951 IX WP Program Chart

Whirlpool AKR 951 IX WP Program Chart

în alte limbi

Lucrări conexe

Alte documente