RIDGID 535A Manual de utilizare

RIDGE TOOL COMPANY

535 Manual

Chuck/

535 Auto

Chuck

P. 1

P. 23

P. 49

P. 75

P. 101

P. 127

P. 153

P. 177

P. 201

P. 225

P. 249

P. 273

P. 297

P. 321

P. 345

P. 369

P. 393

P. 419

P. 443

P. 467

P. 491

P. 519

P. 543

EN

FR

ES

DE

NL

IT

PT

SV

DA

NO

FI

PL

CZ

SK

RO

HU

EL

HR

SL

SR

RU

TR

KK

999-998-086.09_REV. Cii

535 Manual Chuck/535 Auto Chuck Threading Machines

Table of Contents

Recording Form For Machine Serial Number ............................................................................................................1

Safety Symbols..............................................................................................................................................................2

General Power Tool Safety Warnings

Work Area Safety ........................................................................................................................................................2

Electrical Safety ..........................................................................................................................................................2

Personal Safety ..........................................................................................................................................................3

Power Tool Use And Care ..........................................................................................................................................3

Service........................................................................................................................................................................3

Specific Safety Information

Threading Machines Safety Warnings ........................................................................................................................4

Description, Specifications And Standard Equipment

Description ..................................................................................................................................................................4

Specifications..............................................................................................................................................................6

Standard Equipment ..................................................................................................................................................6

Machine Assembly ........................................................................................................................................................7

Mounting on Stands ....................................................................................................................................................7

Mounting on Bench ....................................................................................................................................................7

Pre-Operation Inspection..............................................................................................................................................7

Machine and Work Area Set-Up....................................................................................................................................8

Die Head Set-Up and Use ............................................................................................................................................9

Removing/Installing Die Head ....................................................................................................................................9

Quick-Opening Die Heads ..........................................................................................................................................9

Self-Opening Die Heads ..........................................................................................................................................10

Semi-Automatic Die Heads ......................................................................................................................................11

Operating Instructions

Changing Operating Speeds ....................................................................................................................................13

Cutting with No. 820 Cutter........................................................................................................................................14

Reaming with No. 341 Reamer ................................................................................................................................14

Threading Pipe..........................................................................................................................................................15

Threading Bar Stock/Bolt Threading ........................................................................................................................15

Left Hand Threading..................................................................................................................................................15

Removing Pipe from the Machine ............................................................................................................................16

Inspecting Threads....................................................................................................................................................17

Preparing Machine for Transport ..............................................................................................................................17

Maintenance Instructions

Cleaning....................................................................................................................................................................17

Top Cover Removal/Installation ................................................................................................................................18

Lubrication ................................................................................................................................................................18

Oil System Maintenance ..........................................................................................................................................18

Priming the Model A Oil Pump ..................................................................................................................................18

Replacing No. 820 Cutter Wheel ..............................................................................................................................19

Jaw Replacement (Auto Chuck Machines)................................................................................................................19

Replacing Jaw Inserts (Manual Chuck Machines) ....................................................................................................19

Replacing Carbon Brushes (Universal Motor Units)..................................................................................................20

V-Belt Tension/Replacement (Induction Motor Units)................................................................................................20

Optional Equipment ....................................................................................................................................................20

Thread Cutting Oil Information ..................................................................................................................................21

Machine Storage..........................................................................................................................................................21

Service And Repair......................................................................................................................................................21

Disposal ......................................................................................................................................................................21

Troubleshooting ..........................................................................................................................................................22

EC Declaration....................................................................................................................................Inside Back Cover

Lifetime Warranty ..........................................................................................................................................Back Cover

*Original Instructions - English

535M/535A Threading Machines

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

535 Manual Chuck/535 Auto

Chuck Threading Machines

535M/535A

WARNING!

Read this Operator’s Manual

carefully before using this

tool. Failure to understand

and follow the contents of

this manual may result in

electrical shock, re and/or

serious personal injury.

999-998-086.09_REV. C2

535 Manual Chuck/535 Auto Chuck Threading Machines

General Power Tool Safety

Warnings*

WARNING

Read all safety warnings, instructions, illustra-

tions and specications provided with this power

tool. Failure to follow all instructions listed below

may result in electric shock, re and/or serious

injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE!

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of flam mable liq-

uids, gases, or dust. Power tools create sparks which

may ignite the dust or fumes.

• Keep children and bystanders away while operat-

ing a power tool. Distractions can cause you to lose

control.

Electrical Safety

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adap ter

plugs with earthed (grounded) power tools. Un -

modified plugs and matching outlets will reduce risk of

electric shock.

• Avoid body contact with earthed or grounded sur-

faces such as pipes, radiators, ranges and refrig-

erators. There is an increased risk of electrical shock

if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk

of electrical shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safe-

ty information. This section is provided to improve understanding of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE indicates information that relates to the protection of property.

NOTICE

DANGER

WARNING

CAUTION

* The text used in the General Power Tool Safety Warnings section of this manual is verbatim, as required, from the applicable UL/CSA 62841-1 edition standard. This

section contains general safety practices for many different types of power tools. Not every precaution applies to every tool, and some do not apply to this tool.

This symbol indicates the risk of machine tipping, caus-

ing striking or crushing injuries.

This symbol indicates the risk of fingers, legs, clothes and

other objects catching and/or wrapping on rotating shafts

causing crushing or striking injuries.

This symbol means read the operator’s manual carefully

before using the equipment to reduce the risk of injury.

The operator’s manual contains important information

on the safe and proper operation of the equipment.

This symbol means always wear safety glasses with side

shields or goggles while using this equipment to reduce

the risk of injury.

This symbol indicates the risk of fingers, hands, clothes

and other objects catching on or between gears or other

rotating parts and causing crushing injuries.

This symbol indicates the risk of electrical shock.

This symbol means do not disconnect foot switch to

reduce the risk of injury.

This symbol means do not block foot switch (lock in ON

position) to reduce the risk of injury.

This symbol means do not wear gloves while operating

this machine to reduce the risk of entanglement.

This symbol means always use a foot switch when using

a threading machine/power drive to reduce the risk of

injury.

999-998-086.09_REV. C 3

moving parts. Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of elec-

tric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces

the risk of electric shock.

Personal Safety

• Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol, or medication. A mo -

ment of inattention while operating power tools may

result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch is

in the OFF-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch

ON invites accidents.

• Remove any adjusting key or wrench before turn-

ing the power tool ON. A wrench or a key left at -

tached to a rotating part of the power tool may result in

personal injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewel ry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

535 Manual Chuck/535 Auto Chuck Threading Machines

Power Tool Use And Care

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it is

designed.

• Do not use the power tool if the switch does not

turn it ON and OFF. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/or

remove the battery pack, if detachable, from the

power tool before making any adjustments, chang-

ing accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting the

power tool accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the pow -

er tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of

untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dif-

ferent from those intended could result in a hazardous

situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

Service

• Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

• Do not use this machine if the foot switch is bro-

ken or missing. The foot switch provides safe control

of the machine, such as shut-off in case of entangle-

ment.

• One person must control the work process, ma -

chine operation and foot switch. Only the operator

should be in the work area when the machine is run-

ning. This helps reduce the risk of injury.

• Never reach into the machine front chuck or rear

centering head. This will reduce the risk of entangle-

ment.

• Read and understand these instructions and the

instructions and warnings for all equipment and

materials being used before operating this tool to

reduce the risk of serious personal injury.

If you have any question concerning this RIDGID

®

product:

– Contact your local RIDGID

®

distributor.

– Visit RIDGID.com to find your local Ridge Tool contact

point.

– Contact Ridge Tool Technical Service Department at

r[email protected], or in the U.S. and

Cana da call (800) 519-3456.

Description, Specications And

Standard Equipment

Description

The RIDGID

®

Model 535 Manual Chuck and 535 Auto

Chuck Threading Machines are electric motor-driven

machines that center and chuck pipe, conduit and bolt

stock and rotates it while cutting, reaming and threading

operations are performed.

The 535 Auto Chuck has an automatic chuck to grip and

center pipe.

Threading dies are mounted in a variety of available die

heads. An integral oiling system is provided to flood the

work with thread cutting oil during the threading operation.

With proper optional equipment, RIDGID

®

Model 535

Manual/535 Auto Threading Machines can be used to

thread larger pipe, short or close nipples or for roll grooving.

Specic Safety Information

WARNING

This section contains important safety information

that is specic to these tool.

Read these precautions carefully before using the

535 Manual Chuck/535 Auto Chuck Threading

Machines to reduce the risk of electrical shock or

other serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE!

Keep this manual with machine for use by the operator.

Threading Machines Safety Warnings

• Keep floor dry and free of slippery materials such as

oil. Slippery floors invite accidents.

• Restrict access or barricade the area when work

piece extends beyond machine to provide a mini-

mum of one meter (3 feet) clearance from the work

piece. Restricting access or barricading the work

area around the work piece will reduce the risk of

entanglement.

• Do not wear gloves. Gloves may be entangled by the

rotating pipe or machine parts leading to personal

injury.

• Do not use for other purposes such as drilling

holes or turning winches. Other uses or modifying this

machine for other applications may increase the risk of

serious injury.

• Secure machine to bench or stand. Support long

heavy pipe with pipe supports. This practice will

prevent the machine from tipping.

• While operating the machine, stand on the side

where the operator control switch is located. Opera -

ting the machine from this side eliminates need to

reach over the machine.

• Keep hands away from rotating pipe and fittings.

Stop the machine before wiping pipe threads or

screwing on fittings. Allow the machine to come to

a complete stop before touching the pipe. This

practice will reduce the chance of entanglement in

rotating parts.

• Do not use this machine to install or remove (make

or break) fittings. This practice could lead to trapping,

entanglement and loss of control.

• Do not operate the machine without all covers

properly installed. Exposing moving parts increases

the probability of entanglement.

999-998-086.09_REV. C4

535 Manual Chuck/535 Auto Chuck Threading Machines

Figure 1A – 535 Manual Chuck Threading Machine

Figure 1B – 535 Manual Chuck Threading Machine

Figure 2A – 535 Auto Chuck Threading Machine

Figure 2B – 535 Auto Chuck Threading Machine

999-998-086.09_REV. C 5

535 Manual Chuck/535 Auto Chuck Threading Machines

Chuck Handwheel

Die Head

No. 820

Cutter

No. 341

Reamer

Chip

Tray

REV/OFF/FOR

(2/0/1)

Switch

Foot Switch

Carriage Handwheel

Length Gauge

Die Head

No. 820 Cutter

No. 341

Reamer

Chip

Tray

REV/OFF/FOR

(2/0/1)

Switch

Foot Switch

Carriage

Handwheel

Length

Gauge

Gear

Shift

Warning

Label

Drain

Plug

Warning

Label

Drain

Valve

Centering

Device

Serial

Number

Plate

Serial

Number

Plate

999-998-086.09_REV. C6

535 Manual Chuck/535 Auto Chuck Threading Machines

Specications*

535 Manual Chuck Machines 535 Automatic Chuck Machines

Pipe Threading Capacity 1/8 to 2 inch (3 to 50 mm) Nominal Pipe Size

Bolt Threading Capacity ¼ to 2 inch (6 to 50 mm) Actual Stock Diameter

LH Threads With Modifications

Motor Type Universal Motor Induction Motor Universal Motor Induction Motor Induction Motor

Phase Single Phase 3 Phase Single Phase 3 Phase

Motor Power 2.3 (1.7) 0.5 (0.37) 2.3 (1.7) 1.8/2.3 (1.35/1.7) 1.5 (1.1) 2.3 (1.7) 2 (1.5) 1.8/2.3 (1.35/1.7)

HP (kW)

Volts V 115 115 230 400 220 110 230 120 400

Frequency Hz 50/60 50 60 50/60 60 50

Current Draw Amp 15 20 7.5 3.5/5.1 4.4 15 7.5 18 3.5/5.1

Operating Speed RPM 36 54 36 35/70 16/46/58 36 16/46/58 35/70

Rotary Type

Rotary Type Rotary Type

2/1/0/1/2

1/0/2

REV/OFF/FOR

2/1/0/1/2

REV/OFF/FOR REV/OFF/FOR

Switch for

Switch

Rotary Type

(2/0/1)

Switch for speed

Controls

(2/0/1) (2/0/1)

speed and

Shifter knob

2/0/1 Switch

Switch Shifter and direction

Switch Switch

direction

for speed knob for control

control (see

selection speed selection (see Figure 19)

Figure 19)

ON/OFF Foot Switch

Front Chuck Speed Chuck with replaceable Rocker-Action Jaw Inserts Automatic with four reversible Forged Jaws

Rear Centering Device Cam Action, rotates with Chuck Automatic, Centering only

Die Heads See RIDGID Catalog for available Die Heads

Cutter Model 820, 1/8" – 2" Full Floating, Self-Centering Cutter

Reamer Model 341, 1⁄8" – 2", 5-Fluted Reamer

Oil System 7 qt (6.6 l), with integrated Gerotor Model MJ Pump (Units prior to 1996 – Model A Oil Pump)

Weight

260 lbs. (118 kg)

350 lbs. 290 lbs.

350 lbs. (159 kg)

(unit with oil and a DH) (159 kg) (132 kg)

Overall Dimension 37" × 21" × 21" (940mm × 535mm × 535mm)

L × W × H (With Tools In Operating Position and Cutter Fully Closed)

Sound Pressure (L

PA

)** 85 dB(A), K=3

Sound Power (L

PW

)** 91 dB(A), K=3

* Refer to your machine serial number plate for information on motor rating and control panel for information on your specific machine.

** Sound measurements are measured in accordance with a standardized test per Standard EN 62481-1.

- Sound emissions may vary due to your location and specific use of these tools.

- Daily exposure levels for sound need to be evaluated for each application and appropriate safety measures taken when needed. Evaluation of exposure levels

should consider the time a tool is switched off and not in use. This may significantly reduce the exposure level over the total working period.

Standard Equipment

Refer to the RIDGID catalog for details on equipment

supplied with specific machine catalog numbers.

The Threading Machine serial number plate is located

on the back cover. The last 4 digits indicate the month and

year of the manufacture.

Figure 3 – Machine Serial Number

Pre-Operation Inspection

WARNING

Before each use, inspect your threading machine

and correct any problems to reduce the risk of seri-

ous injury from electric shock, crushing and other

causes and prevent threading machine damage.

1. Make sure that the threading machine is unplugged

and the REV/OFF/FOR (2/0/1) Switch is in OFF (0)

position.

2. Clean any oil, grease or dirt from the threading

machine, including the handles and controls. This

aids inspection and helps prevent the machine or

control from slipping from your grip. Clean and main-

tain the machine per the Maintenance Instructions.

3. Inspect the threading machines for the following:

• Inspect the cords and plugs for damage or modifi-

cation.

• Proper assembly, maintenance and completeness.

• Any broken, worn, missing, misaligned or binding

parts or other damage.

• Presence and operation of the foot switch. Confirm

that foot switch is attached, in good condition, that it

cycles smoothly and does not stick.

• Presence and readability of the warning labels

(See Figure 1 & 2).

• Condition of the dies, cutter wheel and reamer cut-

ting edges. Dull or damaged cutting tools increase

required force, produce poor results and increase

the risk of injury.

• Any other condition which may prevent safe and

normal operation.

If any problems are found, do not use the threading

machine until the problems have been repaired.

4. Inspect and maintain any other equipment being

used per its instructions to make sure it is functioning

properly.

999-998-086.09_REV. C 7

Selection of appropriate materials and instal-

lation, joining and forming methods is the responsibility of

the system designer and/or installer. Selection of improp-

er materials and methods could cause system failure.

Stainless steel and other corrosion resistant materials can

be contaminated during installation, joining and forming.

This contamination could cause corrosion and premature

failure. Careful evaluation of materials and methods for the

specific service conditions, including chemical and tem-

perature, should be completed before any installation is

attempted.

Machine Assembly

WARNING

To reduce the risk of serious injury during use, fol-

low these procedures for proper assembly.

Failure to mount the threading machine to a stable

stand or bench may result in tipping and serious

injury.

REV/OFF/FOR Switch should be OFF and machine

unplugged before assembly.

Use proper lifting techniques. RIDGID 535 threading

machines weigh 260 lbs. (118 kg) or more.

Mounting on Stands

The Threading Machines can be mounted on various

RIDGID Threader Stands. Refer to RIDGID catalog for

stand information and to the respective Stand Instruction

Sheet for mounting instructions.

Mounting on Bench

The machines can be mounted on a level, stable bench. To

mount the unit on a bench, use four 5/16"-18 UNC bolts in

holes provided at each corner of the machine base. Base

hole spacing is 29.5" x 15.5" (749 mm x 394 mm). Tighten

securely.

535 Manual Chuck/535 Auto Chuck Threading Machines

NOTICE

999-998-086.09_REV. C8

535 Manual Chuck/535 Auto Chuck Threading Machines

the die head. See Die Head Set-Up and Use section

for details.

7. Swing the cutter, reamer and die head up away from

the operator. Make sure they are stable and will not fall

in the work area.

8. If pipe will extend past the chip tray in the front of the

machine or more than 4' (1,2 m) out of the rear of the

machine, use pipe stands to support the pipe and pre-

vent the pipe and threading machine from tipping or

falling. Place the pipe stands in line with machine

chucks, approximately 1/3 of distance from end of the

pipe to the machine. Longer pipe may need more than

one pipe stand. Only use pipe stands designed for

this purpose. Improper pipe supports or supporting

the pipe by hand can cause tipping or entanglement

injuries.

9. Restrict access or set-up guards or barricades to

create a minimum of 3' (1 m) clearance around the

threading machine and pipe. This helps prevent non-

operators from contacting the machine or pipe and

reduces the risk of tipping or entanglement.

10. Position the foot switch as shown in Figure 17, to allow

a proper operating position.

11. Check the level of RIDGID Thread Cutting Oil. Remove

the chip tray and oil pan liner; see that the filter screen

assembly is fully submerged in oil. See Oil System

Maintenance.

12. With the REV/OFF/FOR Switch in OFF position, run the

cord along a clear path. With dry hands, plug the

power cord into properly grounded outlet. Keep all

connections dry and off the ground. If the power cord is

not long enough use an extension cord that:

• Is in good condition.

• Has a three-prong plug like on the threading machine.

• Is rated for outdoor use and contains a W or W-A in

the cord designation (e.g. SOW).

• Has sufficient wire size. For extension cords up to 50'

(15.2 m) long use 16 AWG (1.5 mm

2

) or heavier. For

extension cords 50'-100' (15.2 m - 30.5 m) long

use 14 AWG (2.5 mm

2

) or heavier.

13. Check the threading machine for proper operation.

With hands clear of moving parts:

• Move the REV/OFF/FOR (2/0/1) Switch to the FOR

(1) position. Press and release the foot switch. Chuck

should rotate counter-clockwise when viewed from

the carriage end (see Figure 22). Repeat for REV

position – chuck should rotate clockwise. If the thread-

ing machine does not rotate in the correct direction,

or the foot switch does not control the machine

Machine and Work Area Set-Up

WARNING

Set up the Threading Machine and the work area

according to these procedures to reduce the risk of

injury from electric shock, machine tipping, entan-

glement, crushing and other causes, and to help

prevent threading machine damage.

Secure machine to stable stand or bench. Properly

support pipe. This will reduce the risk of falling

pipe, tipping and serious injury.

Do not use the Threading Machines without a prop-

erly operating foot switch. A foot switch provides

better control by letting you shut off the machine

motor by removing your foot.

1. Check work area for:

• Adequate lighting.

• Flammable liquids, vapors or dust that may ignite. If

present, do not work in area until source is identified,

removed or corrected, and area is completely ven-

tilated. The threading machine is not explosion

proof and can cause sparks.

• Clear, level, stable and dry place for all equipment

and operator.

• Good ventilation. Do not use extensively in small,

enclosed areas.

• Properly grounded electrical outlet of the correct

voltage. Check the machine serial plate for required

voltage. A three-prong or GFCI outlet may not be

properly grounded. If in doubt, have outlet inspected

by a licensed electrician.

2. Inspect the pipe to be threaded and associated fit-

tings. Determine the correct equipment for the job,

see Specifications. Do not use to thread anything oth -

er than straight stock. Do not thread pipe with fittings or

other attachments. This increases the risk of entan-

glement.

3. Transport equipment to work area. See Preparing

Machine for Transport for information.

4. Confirm equipment to be used has been properly in -

spected and assembled.

5. Confirm that the REV/OFF/FOR Switch is in the OFF

position.

6. Check that the correct dies are in the die head and are

properly set. If needed, install and/or adjust the dies in

999-998-086.09_REV. C 9

operation, do not use the machine until it has been

repaired.

• Depress and hold the foot switch. Inspect the mov-

ing parts for misalignment, binding, odd noises or

any other unusual conditions. Remove foot from

the foot switch. If any unusual conditions are found,

do not use the machine until it has been repaired.

For 535 Auto Chuck machines, confirm that the

FOR rotation closes the chuck and REV rotation

opens it.

• Place die head in the use position. Depress and hold

the foot switch. Check for oil flow through the die

head. Remove foot from the foot switch.

14. Move the REV/OFF/FOR Switch to the OFF posi-

tion, and with dry hands unplug the machine.

Die Head Set-Up and Use

The 535 Manual Chuck/535 Auto Chuck Threading Ma -

chines can be used with a variety of RIDGID Die Heads to

cut pipe and bolt threads. Information is included here for

Quick-Opening, Self-Opening and Semi-Automatic Die

Heads. See the RIDGID catalog for other available die

heads.

Die Heads using Universal Dies for pipe require one set of

dies for each of the following pipe size ranges: (

1

/

8

"), (

1

/

4

" and

3

/

8

"), (

1

/

2

" and ¾") and (1" through 2"). NPT/NPSM dies

must be used in NPT Die Heads and BSPT/BSPP dies

must be used in BSPT Die Heads – The cam plate is

marked for each.

Die heads using Bolt dies require a dedicated set of dies

for each specific thread size.

High Speed dies are recommended for threading at 40

rpm and higher speeds. See the RIDGID catalog for dies

available for your die head.

Always cut a test thread to confirm proper thread size after

changing/adjusting the Dies.

Removing/Installing Die Head

Insert/remove Die Head Post into mating hole in car-

riage. When fully inserted, the Die Head will be held in

place. When it is installed, the Die Head can be pivoted on

post to align it with pipe or it can be swung up and out of

the way to allow use of cutter or reamer.

Quick-Opening Die Heads

Quick opening die heads include Model 811A and 531/532

Bolt. Quick opening die heads are manually opened and

closed for user specified thread length.

Figure 4 – Quick-Opening Die Head

Inserting/Changing the Dies

1. Place the die head with numbers facing up.

2. Move throwout lever to OPEN position (Figure 5).

Figure 5 – Open/Closed Lever Position

3 Loosen clamp lever

approximately three

turns.

4. Lift tongue of wash-

er out of slot in size

bar. Move washer to

end of slot (Figure

6).

5. Remove dies from

the die head.

6. Insert appropriate dies into the die head, numbered

edge up until the indicator line is flush with the edge of

the die head (see Figure 6). Numbers on the dies

must correspond with those on the die head slots.

Always change dies as sets – do not mix dies from dif-

ferent sets.

7. Move link index mark to align with desired size mark on

size bar. Adjust die insertion as needed to allow move-

ment. Washer tongue should be in slot to left.

8. Tighten clamp lever.

535 Manual Chuck/535 Auto Chuck Threading Machines

Throwout Lever

Size Bar

Washer Tongue

Link

Clamp Lever (Hex Nut

on Mono Dies)

Post

Dies

Hole for Locking Pin (LH Die Heads)

Throwout

Lever

Throwout

Lever

Open

Closed

Indicator

Line

Figure 6 – Inserting Dies

Indicator

Line

999-998-086.09_REV. C10

535 Manual Chuck/535 Auto Chuck Threading Machines

Inserting/Changing the Dies

1. Place the die head with numbers facing up.

2. Make sure the trigger assembly is released and die

head OPEN by pulling the trigger slide away from the

die head. Stay clear of the spring loaded Throwout

Lever while releasing trigger assembly.

Figure 9 – Open/Closed Position

3. Loosen clamp lever ap proximately six full turns.

4. Pull lock screw out of size

bar slot so roll pin will by -

pass slot. Position size

bar so that the index line

on lock screw is a ligned

with the RE MOVE DIES

mark.

5. Remove dies from the die

head.

Insert appropriate dies into

the die head, numbered

edge up until the indicator line is flush with the edge of

the die head (see Fi gure 10). Num bers on the dies

must cor res pond with those on the die head slots.

Always change dies as sets – do not mix dies from dif-

ferent sets.

6. Move size bar so in dex line on lock screw is a ligned

with desired size mark. Adjust die insertion as needed

to allow movement.

7. Make sure roll pin points to ward REMOVE DIES

mark.

8. Tighten the clamp lever.

Adjusting Thread Size

1. Install the die head and move the die head into thread-

ing position.

2. Loosen clamp lever.

3. Position size bar so index line on lock screw is aligned

with desired size mark on size bar.

Adjusting Thread Size

1. Install the die head move the die head into threading

position.

2. Loosen clamp lever.

3. Start with link index mark a ligned with desired size

mark on size bar. On Bolt die heads, set link mark at

line in size bar. For bolt threads with Universal die

head, set all bolt dies at BOLT

line on size bar (Figure 7).

4. If thread size needs to be ad -

justed, set the link index mark

slightly off the mark on size

bar in the direction of OVER

(larger diameter thread, less

turns of fitting engagement) or

UNDER (smaller thread diam-

eter, more turns of fitting en -

gage ment) markings.

5. Tighten clamp lever.

Opening the Die Head at the End of the Thread

At the end of the thread:

• Pipe Threads – End of threaded pipe is flush with the

end of the number 1 die.

• Bolt Threads – Thread the desired length – watch

closely for any interference between the parts.

Move the throwout lever to the OPEN position, retracting

dies.

Self-Opening Die Heads

The Model 815A Die Heads are self-opening die heads.

For ½" through 2" pipe sizes, a trigger can be used to open

the diehead when the thread is complete. For

1

/

8

" to

3

/

8

"

sizes, and if desired for the other sizes, the die head is

manually opened when the thread is complete.

Figure 8 – Universal Self-Opening Die Head

Figure 7 – Adjusting

Thread Size

Link

Index

Mark

Size

Bar

“Under”

“Over”

Throwout

Lever

Trigger

Assembly

Clamp Lever

Size Bar

Roll Pin

Index

Line

Lock

Screw

“Remove Dies” Mark

Trigger

Slide

Throwout

Lever

Open

Closed

Throwout

Lever

Figure 10 – Inserting Dies

Indicator Line

Indicator

Line

Indicator

Line

Figure 13 – Semi-Automatic Die Head

Inserting/Changing the Dies

1 Place the die head with numbers facing up.

2. Depress handle so that cam plate rests against the

change die stop (Figure 13). The cam plate/handle

assembly is spring loaded and will move when de -

pressed.

3. Pull the plunger knob and rotate the handle and cam

plate counter-clockwise until it stops.

4. Remove dies from the die head.

5. Insert appropriate dies into the die head, numbered

edge up until the indicator line is flush with the edge of

the diehead (see Figure 14). Numbers on the dies

must correspond with

those on the die head

slots. Always change dies

as sets – do not mix dies

from different sets.

6. Rotate the handle clock-

wise so that the plunger

knob is flush against the

die head.

Adjusting Thread Size

1 Install the die head and move the die head into thread-

ing position.

2 Loosen the screw for the position block for desired pipe

size.

3 Start with the position block index line on the middle

size bar mark.

4 If thread size needs to be adjusted, set the index line

slightly off the mark on size bar in the direction of the

handle for larger diameter thread, (less turns of fit-

ting engagement) or away from handle for smaller

thread diameter (more turns of fitting engagement).

4. If thread size needs to be ad -

justed, set the lock screw index

line slightly off the mark on size

bar in the direction of OVER

(larger dia meter thread, less

turns of fitting engagement) or

UNDER (smaller thread dia -

meter, more turns of fitting en -

gagement) markings.

5. Tighten clamp lever.

Trigger Slide Adjustment

Position the Trigger Slide for the size of pipe being thread-

ed (see Figure 12).

•

1

/

2

" and

3

/

4

" – End of pipe should hit foot of Trigger

Slide.

• 1" to 2" – End of pipe should hit

the shank of the Trigger Slide.

For

•

1

/

8

", ¼" and

3

/

8

" pipe

• Longer or shorter threads

• Bolt threading

Push trigger slide up and out of the

way. Die head must be opened manu-

ally.

Opening the Die Head at the End of the Thread

When using trigger it will contact the end of pipe, causing

the die head to automatically open. Stay clear of the spring

loaded Throwout Lever when it releases.

To open the die head manually (with trigger slide up), at

the end of the thread:

• Tapered Pipe Threads – End of pipe is flush with

the end of the number 1 die.

• Bolt and Straight Threads – Thread the desired

length – watch closely for any interference between

the parts.

Move the throwout lever to the OPEN position, retracting

dies.

Semi-Automatic Die Heads

Semi-Automatic Die Heads include Model 816/817 NPT

(RH) die heads. The Semi-Automatic Die Heads can be

quickly adjusted from size to size and are manually opened

and closed for user specified thread length.

999-998-086.09_REV. C 11

535 Manual Chuck/535 Auto Chuck Threading Machines

Figure 11 – Adjusting

Thread Size

Lock

Screw

Index

Line

Size

Bar

“Over”

“Under”

1" thru 2"

pipe hit

this

surface

Trigger

Slide

1

/

2

" and

3

/

4

"

pipe hit this

surface

Figure 12 – Setting

the

Trigger

Plunger

Knob

Handle

Position Blocks

Change Die

Stop

Post

Front (Closed)

Back (Open)

Cam Plate

Figure 14 – Inserting Dies

Indicator Line

999-998-086.09_REV. C12

535 Manual Chuck/535 Auto Chuck Threading Machines

5 Securely tighten the position block screw.

6 Always make sure position block type matches (Figure

15).

Figure 15 – Adjusting Thread Size

Opening the Diehead at the end of the Thread

When the end of the pipe is flush with the end of the

number 1 die, press the handle to open die head and

retract the dies. Do not run machine in reverse (REV) with

dies engaged.

Operating Instructions

WARNING

Do not wear gloves or loose clothing. Keep sleeves

and jackets buttoned. Loose clothing can become

entangled in rotating parts and cause crushing and

striking injuries.

Keep hands away from rotating pipe and parts. Stop

the machine before wiping threads or screwing on t-

tings. Do not reach across the machine or pipe. To

prevent entanglement, crushing or striking injuries,

allow machine to come to a complete stop before

touching the pipe or machine chucks.

Do not use this machine to make or break (tighten or

loosen) ttings. This can cause striking or crushing

injuries.

Do not use a threading machine without a properly

operating foot switch. Never block a foot switch in

the ON position so that it does not control the

threading machine. A foot switch provides better

control by letting you shut off the machine motor by

removing your foot. If entanglement should occur

and power is maintained to the motor, you will be

pulled into the machine. This machine has high

torque and can cause clothing to bind around your

arm or other body parts with enough force to crush

or break bones or cause striking or other injuries.

One person must control both the work process

and the foot switch. Do not operate with more than

one person. In case of entanglement, the operator

must be in control of the foot switch.

Follow operating instructions to reduce the risk of

injury from entanglement, striking, crushing and

other causes.

1. Make sure that machine and work area is properly set

up and that the work area is free of bystanders and

other distractions. The operator should be the only per-

son in the barricaded area while the machine is oper-

ated.

The cutter, reamer and die head should be up away

from the operator, do not place in the operating posi-

tion. Make sure they are stable and will not fall in the

work area.

Fully open the chucks of the threading machine. For

Manual Chuck machines, turn the front chuck hand-

wheel clockwise (see Figure 16). For Auto Chuck ma -

chines, move the REV/OFF/FOR (2/0/1) Switch to the

REV (2) position, depress and release the foot switch.

2. Insert pipe shorter than 2’ (0,6 m) from the front of the

machine. Insert longer pipes through either end so that

the longer section extends out beyond the rear of

the threading machine. Confirm that pipe stands are

properly placed.

3. If needed, mark the pipe. Place pipe so that the area to

be cut or end to be reamed or threaded is approxi-

mately 4" (100 mm) from the front of the chuck. If

closer, the carriage may strike the machine during

threading and damage the machine.

4. Chuck the pipe.

For Manual Chuck machines: Turn the rear center-

ing device counterclockwise (viewed from rear of

machine) to close down onto pipe. Make sure that the

pipe is centered in the jaws. This improves pipe sup-

port and gives better results.

Figure 16 – Chucking Pipe

Turn the front chuck handwheel counterclockwise

(viewed from front of machine Figure 16) to close

Position

Block

Pipe Size

Index Line

Screw

Position Block

Type

Size Bar

Close

Open

999-998-086.09_REV. C 13

535 Manual Chuck/535 Auto Chuck Threading Machines

down onto pipe. Make sure that the pipe is centered in

the inserts. Use repeated and forceful counterclockwise

spins of the handwheel to secure the pipe in front

chuck.

For Auto Chuck machines: Move the REV/OFF/ FOR

(2/0/1) Switch to the FOR (1) position and step on the

foot switch. The machine will automatically center and

grip the pipe or stock. If pipe is chucked off center, run

the machine in REV to release and re-chuck. Do not

handle rotating pipe. Auto chuck machines only grip

pipe when rotating.

5. Assume a proper operating position to help maintain

control of the machine and pipe (See Figure 17).

• Stand on the REV/OFF/FOR Switch side of the

machine with convenient access to the tools and

switch.

• Be sure that you can control the foot switch. Do not

step on foot switch yet. In case of emergency, you

must be able to release the foot switch.

• Be sure that you have good balance and do not

have to overreach.

Figure 17 – Operating Position

Changing Operating Speeds

535 Threading machines come in single and multiple

speed versions. Any speed may be used for cutting and

reaming.

Threading Speed Selection

• Up to 36 RPM – Suitable for threading up to 2" pipe,

bolt threading, high torque applications like stainless

steel and high hardness material.

• 46 RPM – Suitable for threading up to 2" pipe. High

Speed Dies are recommended.

• 54 and 58 RPM – Suitable for threading up to 1

1

/

4

" pipe.

High Speed Dies are recommended.

• Higher than 58 RPM – Not suitable for threading. Use

for cutting and reaming only.

If the machine stalls while operating, immediately release

foot switch and change to low speed. Do not change

speed while cutting, reaming or threading.

If equipped with a shifter (see Figure 18), to shift:

Figure 18 – 535 Shifter

1. Pull the shifter knob out.

2. Move the shifter to the desired speed position and

release the knob into detent.

If shifter cannot be moved, leave in current speed set-

ting. Depress and release the foot switch, allow the

machine to come to a full stop and try shifting again.

Do not shift while the machine is rotating.

400 Volt three phase 535 machines can be operated in 35

or 70 rpm. This is controlled by the machine switch, which

is marked 2-1-0-1-2. 0 is the OFF position, 1 is 35 rpm (For -

ward and Reverse), 2 is 70 rpm (Forward and Reverse).

See Figure 19.

Figure 19 – 400 V 3 phase Speed and Direction Control

Shifter

REV FOR

2

11

0

2

OFF

Switch Position

35 RPM

70 RPM

999-998-086.09_REV. C14

535 Manual Chuck/535 Auto Chuck Threading Machines

Cutting with No. 820 Cutter

1. Open cutter by turning the feed screw counterclock-

wise. Lower the cutter into cutting position. Align the

cutter wheel with the mark on pipe. Cutting threaded

or damaged sections of pipe can damage the cutter

wheel.

Length Gauge Use – Place cutting wheel blade against

the end of pipe and set length gauge pointer to “0”

(Figure 20A). Raise cutter and turn carriage hand-

wheel until the pointer is at the length desired. Lower

the cutter into cutting position. See Figure 20B.

Figure 20A – Cutter Wheel Blade Against End of Pipe. Set

Pointer to Zero (0)

Figure 20B – Length Gauge Pointer At Desired Length

2. Tighten the cutter feed screw handle to bring the cut-

ter wheel firmly in contact with the pipe while keeping

the cutter wheel aligned with the mark on pipe.

3. Move the REV/OFF/FOR Switch to the FOR position.

4. With both hands, grasp the pipe cutter feed handle.

5. Depress the foot switch.

6. Tighten the feed screw handle one-half turn per rota-

tion of the pipe until the pipe is cut. More aggressive

tightening of the handle reduces cutter wheel life and

increases burr formation. Do not support the pipe

by hand. Let the cut off piece be supported by the

threading machine carriage and pipe stand.

Figure 21 – Cutting Pipe with Cutter

7. Remove foot from the foot switch.

8 Move the REV/OFF/FOR Switch to the OFF position.

9. Raise the cutter into position up away from the oper-

ator.

Reaming with No. 341 Reamer

1. Move the reamer into reaming position. Make sure

that it is securely positioned to prevent it from moving

during use.

2. Extend reamer by releasing latch and sliding the

reamer towards pipe until the latch engages.

3. Move the REV/OFF/FOR (2/0/1) Switch to the FOR

(1) position.

4. With both hands, grasp the carriage handwheel.

5. Depress the foot switch.

Figure 22 – Reaming Pipe with Reamer, Machine Rotation

6. Turn carriage handwheel to move the reamer to the

FOR

(1)

REV

(2)

2 in

REV

(2)

end of the pipe. Apply slight pressure to the hand-

wheel to feed the reamer into pipe to remove the

burr as desired.

7. Remove foot from the foot switch.

8. Move the REV/OFF/FOR Switch to the OFF position.

9. Retract the reamer by releasing latch and sliding the

reamer away from pipe until the latch engages.

10. Move reamer up away from the operator.

Threading Pipe

Due to differing pipe characteristics, a test thread should

always be performed before the first thread of the day or

when changing pipe size, schedule or material.

1. Lower the die head into the threading position. Confirm

that the dies are correct for the pipe being threaded and

properly set. See the Die Head Set-Up and Use section

for information on changing and adjusting dies.

2. If needed, chose a correct operating speed for the

application. See Changing operating Speeds section.

3. Move the REV/OFF/FOR Switch to the FOR position.

4. With both hands, grasp the carriage handwheel.

5. Depress the foot switch.

6. Confirm cutting oil flow through the die head. Current

535 Threading Machines use through head oiling.

Machines made prior to 1996 have an oil spout which

must be swung to the down position to flood dies

with oil.

Figure 23 – Threading Pipe

7. Turn carriage handwheel to move the die head to

the end of pipe. Apply slight force to the handwheel to

start the die head onto the pipe. Once the die head

starts threading, no more force is required on the

carriage handwheel.

999-998-086.09_REV. C 15

535 Manual Chuck/535 Auto Chuck Threading Machines

8. Keep your hands away from the rotating pipe. Make

sure the carriage does not hit the machine. When the

thread is complete, open the die head (if the die head

does not open automatically). Do not run machine in

Reverse (REV) with dies engaged.

9. Remove foot from the foot switch.

10. Move the REV/OFF/FOR Switch to the OFF posi-

tion.

11. Turn the carriage handwheel to move the die head

past the end of the pipe. Raise the die head into

position up away from the operator.

12. Remove the pipe from the machine and inspect the

thread. Do not use the machine to tighten or loosen fit-

tings on the thread.

Threading Bar Stock/Bolt Threading

Bolt threading is similar to the pipe threading process. The

stock diameter should never exceed the thread major diam-

eter.

When cutting bolt threads, the correct dies and die head

must be used. Bolt threads may be cut as long as needed,

but make sure the carriage does not hit the machine. If long

threads are required:

1. At the end of carriage travel, leave the diehead closed,

remove foot from the foot switch and move the REV/ -

OFF/ FOR Switch to the OFF position.

2. For Manual Chuck machines: Open the chuck and

move the carriage and workpiece to the end of the

machine. Re-chuck the rod and continue threading.

3. For Auto Chuck machines: Move the REV/OFF/FOR

Switch in the REV position and tap the foot switch to

release the workpiece. Slide the carriage and work-

piece to the end of the machine. Re-chuck the rod and

continue threading.

Left Hand Threading

Cutting left hand threads is similar to the right hand thread-

ing process. To cut left hand threads left hand threading kit,

left hand die heads and dies are required. For reaming

with the machine in reverse a Model E-863 Reamer Cone

(cat# 46660) is required.

1. For 535 Manual Chuck machines: Install the left

hand threading kit (Cat# 96517) as per the kit instruc-

tions to allow oil flow in REV. (535 Threading Machines

made prior to 2001 do not require the kit).

2. For 535 Auto Chuck machines: Install the 535

Automatic Reversing Valve Kit (Cat# 12138) as per kit

instructions to allow oil flow in REV. The kit includes a

selector for LH or RH oil flow. See Figure 24.

999-998-086.09_REV. C16

535 Manual Chuck/535 Auto Chuck Threading Machines

Figure 25B – Rear Pivot Rod Support - Pin Placement

3. Place a 5/16" pin 2" long through the holes in carriage

rest and left hand die head to retain in place (see

Figure 26).

Figure 26 – Retaining LH Die Head in Place

4. Threading will be done with the REV/OFF/FOR switch

in the REV position. For the Auto Chuck machines, the

chuck operation will be reversed – the chuck will

close down and grip pipe in REV and open in FOR.

Removing Pipe from the Machine

1. Un-chuck the pipe.

For Manual Chuck machines: With the REV/OFF/ -

FOR Switch in OFF position and the pipe stationary,

use repeated and forceful clockwise spins of the

handwheel to loosen the pipe in the chuck. Open

the front chuck and the rear-centering device. Do not

reach into chuck or centering device.

For Auto Chuck machines: Move the REV/ OFF/ FOR

(2/0/1) Switch to the REV (2) position. Press and

release the foot switch, the machine will release the

pipe. Move the REV/OFF/FOR Switch to the OFF

(0) position.

Figure 24 – LH or RH Oil Flow Selector

Left hand threading requires the chuck jaws to grip the

pipe during REV rotation of the machine.

a. Make sure that the REV/OFF/FOR (2/0/1) switch is

in the OFF (0) position and the cord is unplugged

from the outlet.

b. Remove rear cover. Loosen cover screws and

rotate cover to remove (Figure 25A).

c. Remove E-clips and rear pivot rod support (Figure

25B).

d. Position the rear pivot rod support so that pin faces

outward and reinstall (Figure 25B).

e. Reinstall retaining E-clips and rear cover.

f. With the machine completely reassembled and

the chuck cover installed, place the REV/OFF/FOR

in the FOR position to open the chuck in prepara-

tion to left hand thread. In this configuration, the

machine can be used for both Left Hand and Right

Hand threading, depending on whether FOR or

REV is used to open the empty chuck.

g. To convert back to Right Hand threading only, turn

over the rear pivot rod support so that pin faces

inward and reinstall (Figure 25B).

Figure 25A – Removing Rear Cover

Right Hand Thread

Outward

Inward

L.H. & R.H. Threading

R.H. Threading

Rear

Pivot Rod

Support

Place Pin

Through

Holes

Loosen

Screws

Rotate Cover

Place Pin

Through

Holes

2. Clean the chips and other debris from the chip tray.

Remove or secure all loose equipment and material

from the machine and stand prior to moving to prevent

falling or tipping. Clean up any oil or debris on the floor.

3. Place the cutter, reamer and die head in the operating

position.

4. Coil up the power cord and foot switch cord. If need-

ed, remove the machine from the stand.

5. Use care in lifting and moving, follow stand instruc-

tions. Be aware of the machine weight.

Figure 28 – Machine prepared for Transport

Maintenance Instructions

WARNING

Make sure that the REV/OFF/FOR Switch is in the

OFF position and the machine is unplugged before

performing any maintenance or making any adjust-

ments.

Maintain threading machine according to these

procedures to reduce the risk of injury from elec-

trical shock, entanglement and other causes.

Cleaning

After each use, empty the threading chips from the chip

tray and wipe out any oil residue. Wipe oil off exposed sur-

faces, especially areas of relative motion like the car-

riage rails.

2. Firmly grip the pipe and remove from the machine.

Carefully handle the pipe as the thread may still be hot

and there may be burrs or sharp edges.

Inspecting Threads

1. After removing the pipe from the machine, clean the

thread.

2. Visually inspect thread. Threads should be smooth

and complete, with good form. If issues such as

thread tearing, waviness, thin threads, or pipe out-of

roundness are found, the thread may not seal. Refer

to the Troubleshooting Chart for help in diagnosing

these issues.

3. Inspect the size of the thread.

• The preferred method of checking thread size is with

a ring gauge. There are various styles of ring

gauges, and their usage may differ from that shown

here.

• Screw ring gauge onto the thread hand tight.

• Look at how far the pipe end extends through the

ring gage. The end of the pipe should be flush with

the side of the gauge plus or minus one turn. If

thread does not gauge properly, cut off the thread,

adjust the die head and cut another thread. Using a

thread that does not gauge properly can cause

leaks.

Figure 27 – Checking Thread Size

• If a ring gauge is not available to inspect thread size,

it is possible to use a new clean fitting representa-

tive of those used on the job to gauge thread size.

For 2" and under NPT threads, the threads should

be cut to obtain 4 to 5 turns to hand tight engage-

ment with the fitting and for BSPT it should be 3

turns.

4. See Adjusting Thread Size under Die Head Set-Up

and Use heading to adjust thread size.

5. Test the piping system in accordance with local codes

and normal practice.

Preparing Machine for Transport

1. Make sure that the REV/OFF/FOR switch is in the

OFF position and the cord is unplugged from the

outlet.

999-998-086.09_REV. C 17

535 Manual Chuck/535 Auto Chuck Threading Machines

Flush

(Basic Size)

One Turn Large

(Maximum Size)

One Turn Small

(Minimum Size)

Ring

Gauge

999-998-086.09_REV. C18

535 Manual Chuck/535 Auto Chuck Threading Machines

Figure 30 – Removing Chip Tray

Replace thread cutting oil when it becomes dirty or con-

taminated. To drain the oil, position a container under drain

plug at end of reservoir and remove plug. Clean build up

from the bottom of the reservoir. Use RIDGID Thread

Cutting Oil for high quality threads and maximum die life.

Reservoir in the base will hold approximately 7 qt (6,6 l) of

thread cutting oil.

The oil pump should self-prime if the system is clean. If it

does not, this indicates that the pump is worn and should be

serviced. Do not attempt to prime the pump.

Priming the Model A Oil Pump

Current 535 threading machines use self-priming pumps.

Machines made prior to June 1, 1996 have the Model A oil

pump and may require priming.

RIDGID Model 535, 500 and 500A

Thread ing Machines equipped with a Model A oil pump

should have an oil pump priming port tube extension and

a top cover access hole to allow the oil pump to be primed

without removing the top cover of the machine. This

reduces the risk of injury from contacting the internal

gearing of the machine. If your pre-1996 machine does not

have a priming port tube extension and access hole in the

top cover, we strongly recommend that they be added.

Contact Ridge Tool Technical Service Department at

rtctechservices@emerson.com, or (800) 519-3456 regard-

ing a retrofit policy.

If the jaw inserts do not grip and need to be cleaned, use

a wire brush to remove any build up of pipe scale, etc.

Top Cover Removal/Installation

The top cover is retained by fasteners at each corner. The

fasteners are secured to the cover to prevent loss. Do not

operate the threading machine with cover off.

Lubrication

On a monthly basis (or more often if needed) lubricate all

exposed moving parts (such as carriage rails, cutter wheels,

cutter feed screw, jaw inserts and pivot points) with a light

lubricating oil. Wipe off any excess oil from exposed sur-

faces.

Every 2-6 months, depending on usage, remove top cover

and use grease gun to apply Lithium based EP (Extreme

Pressure) grease to the shaft bearing grease fittings (Figure

29). Apply a small amount of grease to the exposed drive

gear teeth.

Figure 29 – Lubrication Points

Do not operate the threading machine with cover off. Always

replace cover immediately after lubricating machine.

Oil System Maintenance

Slide the chip tray out.

Keep oil filter screen clean for sufficient oil flow. Oil filter

screen is located in the bottom of oil reservoir. Loosen the

screw that secures filter to base, remove filter from oil line

and clean. Do not operate machine with oil filter screen

removed.

WARNING

Grease

Fittings

Drive

Gear

Teeth

Oil Filter

Screen

Chip Tray

Pagina se încarcă ...

RIDGID 535A Manual de utilizare

Acest manual este potrivit și pentru

RIDGID 535A Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente