Smithco 7576 Tournament Ultra Lite Roller Manualul proprietarului

TOURNAMENT ULTRA

LITE CE

7576

SN: T8298

Revised August, 2019

Product Support: 1020 Hawaii Rd; Humboldt, KS 66748

1-888-422-5173 [email protected]

Wayne, PA 19087 www.smithco.com

Parts Manual

TABLE OF CONTENTS

TITLE PAGE

Frame Drawing 1

Frame Parts List 2

Roller Housing Drawing 3

Roller Housing Parts List 4

Steering Drawing 5

Steering Parts List 6

Engine Drawing & Parts List 7

Wiring Drawing & Parts List 8

Hydraulic Plumbing Drawing 9

Hydraulic Plumbing Parts List 10

750-847 Pump Drawing 11

750-847 Pump Parts List 12

Pump Linkage Drawing 13

Pump Linkage Parts List 14

Performance Chart 15-16

750-555 Light Kit Parts List & Installation 17-19

7520 Trailer Drawing 20

7520 Trailer Parts List 21

Guide Rail & Roller Stop Installation 22

7525 Trailer Drawing f/7000 23

7525 Trailer Parts List f/7000 24

Trailer Spring Placement 25

CE 26-28

SMITHCO Warranty 29-30

7576 FRAME DRAWING

1

7576 FRAME PARTS LIST

REF# PART# DESCRIPTION QTY.

1 832-123-2 Low-Back “Smithco” Seat Assembly 1

2 750-913 Engine Cover 1

3 750-917 Engine Cover Hold Down 4 7/8” 2

4 750-891 Gas Shock Assembly w/Ball Stud 1

5 750-911 Seat Hinge 1

6 750-916 Oil Tank 1

7 750-908 Deck Plate 1

8 720-078-1 5/16” x 1” Clevis Pin 2

9 720-079 Cotter Pin 3/32” x ¾” 2

10 11-101-1 ¼” Fine Thread Yoke 2

11 750-915 Left Foot Pedal Rod 1

12 750-914 Right Foot Pedal Rod 1

14 750-912 Foot Pedal 2

15 10-007 Bushing 4

16 750-906 Main Frame 1

17 750-192 1 1/8” Poly Hex Nut & Cap 2

18 932-042 Thick Slotted Hex Nut 1 ¼” – 12 2

19 709-143-1 1/8” x 2 ½” Cotter Pin 2

20 932-023 Bearing 4

21 932-024 Spacer 2

22 932-022 Seal 4

23 400-061 ½” x 3 1/2” Bolt 1

24 750-186 Spacer ½” ID x ¾” OD x ½” 2

25 750-907 Swivel Axle Bracket 1

26 750-118-1 Oil Tank Cap 1

27 400-112 ½” Lock Nut 1

28 400-008 5/16” x 2 ½” Bolt 2

29 400-109 5/16” Lock Nut 2

30 400-116 3/8” Lock Nut 2

31 400-018 3/8” x 2 ½” Bolt 2

32 44-967 5/16” FT Tie Rod End 2

33 400-002 5/16” x 1” HHCS 2

34 400-281 5/16” Flange Locknut 2

35 750-942 Left Outer Step (CE Only) 1

36 750-943 Right Outer Step (CE Only) 1

37 750-269 Battery Box 1

2

7576 ROLLER HOUSING DRAWING

3

7576 ROLLER HOUSING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-825 Left Roller Housing 1

2 750-826 Right Roller Housing 1

4 40-199 Idler Spring 1

5 1083 #50 Master Link 3

6 750-415 #50 Chain 50 pitch w/3 Connecting Links 1

7 750-821 Roller Cylinder 2

8 400-105 ½” – 13 Hex Nut 5

9 713-806 Ball Joint 2

10 400-056 ½” – 13 X 2 ½” HHCS 2

11 400-136 ½” – 20 Fine Thread Hex Nut 2

12 750-411 Tie Rod 1

13 400-044 ¼” – 20 x 1” Bolt 2

14 400-208 ¼” Lock Washer 2

15 720-004 Flange Bearing 2

16 750-721 Spacer 1 ¼” 2

17 750-220-2 Hub w/Plate, Bushing & Shaft 2

21 750-802 Hub 4 Bolt 2

22 1189 Lug Bolt 8

23 400-210 ½” Lock Washer 8

24 400-105 ½” – 13 Hex Nut 8

25 750-801-3 Castle Nut 2

26 740-023 3/16” x ¾” Key 2

27 750-801 Hydro Gear Motor 2

28 750-827 Bolted End Plate f/Housing 2

29 400-209 3/8” Lock Washer 16

30 400-090 3/8” x 1 ¼” Bolt 16

31 400-103 3/8” Hex Nut 8

32 750-873 Steering Chain Adjuster – Turnbuckle 1

4

7576 STEERING DRAWING

5

7576 STEERING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 730-046-2 Steering Wheel Cap 1

2 932-122 5/8” – 18 Hex Jam Nut 1

3 400-143 5/8” Lock Washer 1

4 730-046 Steering Wheel 1

5 832-028-1 Tilt Steering Mechanism & Boot w/Pin 1

6 740-023 3/16” x ¾” Key 1

7 400-073 ¼” x 1” Self Tap Screw 4

8 400-003 5/16” – 18 x 1 ¼” HHCS 4

9 400-102 5/16” – 18 Hex Nut 8

10 750-286 Upper Steering Shaft 1

11 832-030 7/32” x 1 ¼” Spring Pin 1

12 41-120 U-Joint ¾” x ¾” 1

13 1088 3/16” x 1” Key 3

14 750-266 Steering Sprocket Shaft 1

15 750-909 Steering Column 1

16 400-010 5/16” – 18 x 5” HHCS 2

17 400-207 5/16” Lock Washer 8

18 400-314 5/16” x 4 ¼” Bolt 2

19 41-194 Chain Adjuster Bracket 1

20 1036 Jackshaft Bearing 2

21 1075 #40 Jackshaft Sprocket 11T 1

22 41-251 #40 Chain x 108 Pitch w/Connecting Link 1

23 750-148-1 Sprocket & Bearing Shaft 5 ½” 1

24 750-894 Bearing & Sprocket Bracket 1

25 400-103 3/8” – 16 Hex Nut 4

26 400-209 3/8” Lock Washer 4

27 1040 Front Axle Bearing 1

28 750-234 Steering Sprocket 60T 40BS60 x ¾” 1

29 750-315 ¼” x 2 ½” Spring Pin 2

30 750-133-1 50BS 19 x ¾” Sprocket 1

31 750-722 1” Spacer (3/4” ID) 1

32 400-116 3/8” – 16 Locknut 4

33 400-202 5/16” Flat Washer 4

34 400-015 3/8” – 16 x 1 ½” HHCS 4

35 750-107 Steering Column Cover 1

36 750-195 Steering Shaft Bracket 1

37 520-007 Bronze Bushing 2

38 709-382 ¼” 90° Grease Zert 1

39 1088-1 3/16” x 1 ½” Key 1

6

7576 ENGINE DRAWING

7576 ENGINE PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-935 8 HP Engine (Model# GX240UT2 -QAR2) 1

2 400-090 3/8” x 1 ¼” Bolt 8

3 1517 ¼” x 1” Key 1

4 750-851 Pump Hub 17mm w / #5 Key 1

5 720-027 Element 1

6 41-147 Engine Coupling 1” 1

7 750-201 3/16” x 1” Key 1

8 750-127 Bell Housing 6” 1

9 750-127-1 Bell Housing Cover 1

10 750-847 16cc without Aux Charge Pump 1

11 750-211 Engine Base 1

12 750-927 Engine Spacer 4

7

WIRING DRAWING

WIRING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-935 8 HP Engine (Model# GX240UT2-QAR2) 1

2 750-555-7 PS1230 Battery 1

3 750-555-5 Rectifier 1

4 932-119-1 Safety Seat Switch 1

5 942-049 Wiring Harness f/Seat Switch 1

6 750-555-6 Wiring Harness 1

7 750-555-2 Light Kit Battery Box 1

8

HYDRAULIC PLUMBING DRAWING

9

HYDRAULIC PLUMBING PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-916 Oil Tank 1

2 750-825 Left Roller Housing 1

3 750-826 Right Roller Housing 1

4 750-302 Filter Head 1

5 750-801 Wheel Motor 2

6 750-847 16cc without Aug Charge Pump 1

7 750-326 Wheel Motor Fitting 4

8 750-325 Oil Filter Head Fitting 2

9 750-322 Pump Fitting 2

10 750-324 Pump Fitting Top 1

11 750-295 Pump Fitting 1

12 750-920-1 Hyd Hose 57” x ½” (w/o 90° to Straight) 1

13 750-502 Hard Line Clamp 2

14 750-920-2 Hydraulic Hose 14” – Pump to Filter 1

15 750-920-3 Hydraulic Hose 35” 2

16 750-920-4 Hydraulic Hose 11” – Oil Tank to Filter Head 1

17 750-920-5 Hydraulic Hose 7” – Oil Tank to Pump 1

18 750-519 Hard Line Long Left Side 1

19 750-520 Hard Line Short Left Side 1

20 750-506 Hard Line Long Right Side 1

21 750-507 Hard Line Short Right Side 1

22 750-923 Drain Cap 1

23 750-920-6 Drain Hose 1

24 750-920-7 Hydraulic Hose 52” 1

25 750-118-2 Oil Tank Cap w/Dipstick 1

NOTE: OIL FILTER IS A PART# 750-300

COMPLETE HOSE KIT IS A PART# 750-920

10

750-847 PUMP DRAWING

11

750-847 PUMP PARTS LIST

REF# PART# DESCRIPTION QTY.

1 750-847-3 Retaining Ring 1

2 750-847-4 Lip Seal 1

3 750-847-5 Spacer 1

4 750-847-6 Shaft Kit 1

5 750-847-7 Housing 1

6 750-847-8 Trunnion Seal Kit 1

7 750-228-15 Pin 2

8 750-847-9 O-Ring 1

9 750-847-10 Charge Relief 1

10 750-847-11 Shock Valve Kit 1

11 750-847-12 End Cap 1

12 750-847-11 Shock Valve Kit 1

13 750-847-13 Plug 1

14 750-228-7 Bypass Kit 1

15 750-847-14 Charge Pump 1

16 750-847-15 Screw 4

17 750-847-13 Plug 1

18 750-847-16 Screw 2

19 750-847-17 Valve Plate 1

20 750-847-18 Cylinder Block 1

21 750-847-19 Thrust Bearing 1

22 750-847-20 Swash Plate 1

23 750-128-38 Slot Guide 1

24 750-847-21 Trunnion Arm 1

25 750-849 Seal Kit 1

12

PUMP LINKAGE DRAWING

13

PUMP LINKAGE PARTS LIST

REF.# PART# DESCRIPTION QTY.

1 750-847 16cc without Aug Charge Pump 1

2 750-228-30 Bushing 1

3 750-343-1 Shift Lever Top (New) 1

3 750-343 Shift Lever Top (Old) 1

4 750-344-1 Shift Lever Bottom w/Bolt (Sq. Hole .470) 1

4 750-344 Shift Lever Bottom (Sq. Hole .350) 1

5 750-228-31 Bushing 1

6 750-345 Shift lever Right (Bent) 1

7 750-229-1 Gold Spring 1

8 750-228-32 Nylon Washer 1

9 750-346 Shift Lever Left (Straight) 1

10 750-228-33 Nylon Washer 1

11 750-228-34 5/16” Flat Washer 2

12 750-228-35 Allen Head Bolt 1

13 750-228-36 Allen Head Bolt 1

14 750-228-37 Pump Bracket Kit 1

14

PERFORMANCE CHART

Product Type

PC

PG

PJ

PR

PW

Displacement

in

3

/rev

[cc/rev]

0.37

[6.1]

0.62

[10.2]

0.73

[12]

0.97

[16]

1.33

[21.8]

Input Speed

Maximum Unloaded

Minimum Loaded

rpm

3600

1800

3600

1800

3600

1800

3600

1800

3600

1800

System Operating Pressure

Continuous

Intermittent

Peak

psi

[bar]

psi

[bar]

psi

[bar]

750

[51]

1750

[120]

2500

[172]

1000

[70]

2100

[145]

3500

[240]

1000

[70]

2100

[145]

3500

[240]

1250

[86]

2500

[172]

3750

[260]

1250

[86]

2500

[172]

3750

[260]

Pump Performance

@ 2400 rpm/1000 psi

@ 3000 rpm/1000 psi

@ 3600 rpm/1000 psi

gpm [l/min]

3.6 [13.6]

4.5 [17.0]

5.4 [20.4]

6.1 [23.1]

7.6 [28.8]

9.2 [34.8]

7.1 [26.8]

8.9 [33.6]

10.8 [40.8]

9.6 [36.3]

12 [45.4]

14.4 [54.5]

13.1 [49.6]

16.4 [62.1]

19.6 [74.2]

Case Pressure

Maximum @ Cold Start

Continuous - Max.

psi [bar]

10 [0.7]

4 [0.3]

10 [0.7]

4 [0.3]

10 [0.7]

4 [0.3]

25 [1.7]

10 [0.7]

25 [1.7]

10 [0.7]

Inlet Vacuum

Maximum Continuous Inches Mercury

4

Charge Pump Displacement(s)

in

3

/rev

[cc/rev]

.13

[2.1]

0.11/0.13

[1.9/2.1]

0.19

[3.2]

0.13/0.19

[2.1/3.2]

0.13/0.19

[2.1/3.2]

Auxiliary Pump Displacement

in

3

/rev

[cc/rev]

0.19

[3.2]

0.19

[3.2]

0.19

[3.2]

0.19

[3.2]

0.19

[3.2]

Auxiliary Pump Relief Setting

psi

[bar]

650

[45]

650

[45]

650

[45]

650

[45]

650

[45]

Auxiliary Pump Performance

@3200 rpm, 500 psi, 70 SUS

[13 Cst] oil, & 180°F

gpm

[l/min]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

1.8 - 2.0

[6.8 - 7.6]

Control Torque Required

to Stroke Pump

[Approximate - 20° External Stroke Angle]

75

85

95

105

15

lb-in / 1000 psi

[N-m / 70 bar]

lb-in / 500 psi

[N-m / 35 bar]

[8.5]

55

[6.2]

[9.6]

60

[6.8]

[9.6]

60

[6.8]

[10.7]

75

[8.5]

[11.9]

85

[9.6]

Pump Oil Temperature

Maximum Intermittent (hottest point)

Normal Operating Range

°F

[°C]

°F

[°C]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

230

[110]

-10 to 200

[-23 to 93]

Fluid Viscosity Limits @ 230°F [110°C]

Optimum

Minimum

SUS[cSt]

70 [13]

55 [9]

70 [13]

55 [9]

70 [13]

55 [9]

70 [13]

55 [9]

70 [13]

55 [9]

Weight of Unit

lbs [kg]

7 [3.2]

8 [3.6]

12.65 [5.7]

12 [5.4]

14 [6.3]

Inlet Filtration Requirement

Nominal

micron

25

16

750-555 LIGHT KIT (Optional Accessory)

PART# DESCRIPTION QTY.

750-341-4 Switch Tab 1

750-555-4 Light Mount Bracket 1

750-555-8 Wiring Harness 1

750-555-1 Light Bulbs 2

W132 Loom Clamps 2

Zip Ties 4

INSTALLATION INSTRUCTIONS

1. Bolt the light bracket under the seat plate using the front bolts on the seat. Use the (2)

loom clamps to hold the wires under the seat plate, which are held in place by the front

seat bolts. If the engine cover has expanded metal on it, you can cut out where needed

with a pair of side cut pliers. This allows the bracket to go through.

(Unit with Expanded Metal) (Unit without Expanded Metal)

17

2. Bolt the lights onto the light bracket. Place switch tab on the left light.

3. Connect the wiring harness to the lights, with switch on the left side of machine. Run

wire through loom clamps.

18

Pagina se încarcă ...

Smithco 7576 Tournament Ultra Lite Roller Manualul proprietarului

Smithco 7576 Tournament Ultra Lite Roller Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente