Hikoki EC36DA Manual de utilizare

EC36DA

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Οδηγίες χειρισμού

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

Pokyny na manipuláciu

Инструкция за експлоатация

Uputstvo za rukovanje

Upute za rukovanje

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

hu

cs

tr

ro

sl

sk

bg

sr

hr

el

pl

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

el

pl

hu

cs

tr

ro

sl

sk

bg

sr

hr

2

1

23

4

3

5

6 7

ab

89

4

10 11

12 13

5

English

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power toolʼs operation. If

damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING

Read all safety warnings, instructions, illustrations

and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce

personal injuries.

(Original instructions)

6

English

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water. If

liquid contacts eyes, additionally seek medical

help.

Liquid ejected from the battery may cause irritation

or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range speciﬁ ed in the

instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service

providers.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach

of children and inﬁ rm persons.

CORDLESS AIR COMPRESSOR

SAFETY WARNINGS

1. Don’t expose compressor to rain. Never operate

the compressor in damp or wet locations.

2. Disconnect the compressor.

Always disconnect the compressor from the battery

and remove the compressed air from the tank before

servicing, inspecting, maintaining, cleaning, replacing

or checking any parts.

3. Avoid unintentional starting.

Do not carry the compressor while it is connected to its

battery or when the tank is ﬁ lled with compressed air.

Be sure the power switch in the “OFF” position before

connecting the compressor to its battery.

4. Store compressor properly.

When not in use, the compressor should be stored in

indoor dry place. Keep out of reach of children. Lock-

out the storage area.

5. Consider work area environment.

Keep work area well lit and well ventilated.

Operate the compressor in an open area at least

457 mm away from any wall or object that could restrict

the ﬂ ow of fresh air to the ventilation openings. Do not

place rags or other objects on or near these openings.

Risk of ﬁ re or explosion. Do not carry and operate the

compressor or any other electrical device near the

spray area. Do not use compressor in the presence of

ﬂ ammable liquids or gases.

Never place objects against or on top of compressor.

Compressor produces sparks during operation.

Never use compressor in sites containing lacquer,

paint, benzine, thinner, gasoline, gases, adhesive

agents, and other materials which are combustible or

explosive.

Always operate the compressor in a stable and secure

position to prevent accidental movement of the unit.

Never operate the compressor on a roof or other

elevated positon. Never use on a ladder or unstable

support. Use an additional air hose to reach high

locations.

This compressor contains some components parts

that tend to produce arcs or sparks, and therefore,

when located in a garage, it should be in a room or

enclosure provided for this purpose, and should be

457 mm or more above the ﬂ oor.

6. Keep compressors as far from the spraying area

as possible.

Risk of ﬁ re or explosion. Do not spray ﬂ ammable

liquid in a conﬁ ned area. The spray area must be well

ventilated. Do not smoke while spraying or spray where

parks or a ﬂ ame is present. Use spray gun hose at least

7.6 m long and keep the compressor/motor at least

6.1 m away from explosive vapours. Do not use this

air compressor to spray chemicals. Your lungs can be

damaged by inhaling toxic fumes.

A respirator may be necessary in dusty environments

or when spraying paint. Do not carry while painting.

7. Maintain compressor with care.

Please conduct maintenance in accordance with

page 15.

8. Never use compressor for applications other than

those speciﬁ ed.

Never use compressor for applications other than

those speciﬁ ed in the Instruction Manual.

Following all safety precautions in this manual and the

manufacturer’s instructions in the application manual.

Never use compressed air for breathing or respiration.

7

English

9. Handle compressor correctly.

Operate the compressor according to the instructions

provided herein. Never allow the compressor to be

operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

10. Keep motor air vent clean.

The motor air vent must be kept clean so that air

can freely ﬂ ow at all times. Check for dust build-up

frequently.

11. Never use a compressor which is defective or

operating abnormally.

If the compressor appears to be operating unusually,

making strange noises or vibration, or otherwise

appears defective, stop using it immediately and

arrange for repairs by a HiKOKI authorized service

center.

12. Turn oﬀ the power switch when the compressor is

not used.

When the compressor is not used, turn oﬀ the power

switch, remove the battery and open the drain valve to

discharge the compressed air from the tank.

13. Never touch hot surface.

To reduce the risk of burns, do not touch the delivery

pipe, check valve or pump.

These areas can remain hot for at least 45 minutes

after this compressor is shutdown.

Allow compressor to cool prior to servicing.

14. Drain tank.

Risk of bursting. Water will condense in the tank. If

not drained, water will corrode and weaken the tank

causing a risk of tank rupture.

Drain tank daily or after 4 hours of use. To drain the

tank, open valves slowly and tilt compressor to empty

accumulated water.

Keep face and the other body parts away from outlet of

drain.

Use the safety glasses with side shields when draining

as debris can be kicked up into face.

15. Do not stop compressor by removing the battery.

This could result in damage to the unit.

Use the power switch.

16. Make sure the compressor outlet pressure is set

lower than the maximum operating pressure of

the tool.

Too much air pressure causes a hazardous risk of

bursting.

Check the manufacturer’s maximum pressure rating

for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure

rating.

17. The safety valve must work properly.

Risk of bursting. Before starting the compressor, rotate

the safety valve to make sure that the safety valve

operates smoothly. If the safety valve does not work

properly, over-pressurization may occur, causing tank

rupture or an explosion. Do not use compressor if the

safety valve is stuck or does not operate smoothly.

Have defective safety valve replaced by a HiKOKI

authorized service center.

18. Protect material lines and air lines from damage or

puncture.

Keep the hose and power cord away from sharp

objects, chemical spills, oil, solvents, and wet ﬂ oors.

19. Check hoses for weak or worn condition before

each use, making certain all connections are

secure.

Do not use if a defect is found. Purchase a new hose or

notify an authorized service center for examination or

repair.

20. Keep the exterior of the air compressor dry, clean,

and free from oil and grease.

Always use a clean cloth when cleaning. Never use

brake ﬂ uids, gasoline, petroleum-based products, or

any strong solvents to clean the unit. Following this rule

will reduce the risk of deterioration of the enclosure

plastic.

21. Make sure the hose is free of obstructions or

snags.

Entangled or snarled hoses can cause loss of balance

or footing and may become damaged.

22. Never leave a compressor unattended with the air

hose attached.

23. Do not operate this compressor if it does not

contain a legible warning label.

24. Do not continue to use a compressor or hose that

leaks air or does not function properly.

25. Always disconnect the air supply and battery

before making adjustments, servicing a

compressor, or when a compressor is not in use.

26. Do not attempt to pull or carry the air compressor

by the hose.

27. Your tool may require more air consumption than

this air compressor is capable of providing.

28. Inspect compressor hoses periodically and,

if damaged, have repaired at your nearest

authorized service center.

Following this rule will reduce the risk of injury.

29. Because the cordless air compressor operates

by battery power, be aware of the fact that it can

begin to operate at any time.

30. Check damaged parts and air leak.

Before further use of the compressor, a guard or

other part is damaged should be carefully checked

to determine that it will operate properly and perform

its intended function. Check for alignment of moving

parts, binding of moving parts, breakage of parts,

mounting, air leak, and any other conditions that may

aﬀ ect its operation.

A guard or other part that is damaged should be

properly repaired or replaced by a HiKOKI authorized

service center.

Have defective power switches replaced by a HiKOKI

authorized service center.

Do not use compressor if power switch does not turn it

on and oﬀ .

31. Keep all screws, bolts and guards tightly in place.

Keep all screws, bolts, and guards tightly mounted.

Check their conditions periodically.

32. Do not direct air stream at body.

Risk of injury. Do not direct air stream at persons or

animals.

33. Release the pressure within the system slowly.

Dust and debris may be harmful.

34. Always charge the battery at a temperature of

0°C–40°C. A temperature of less than 0°C will result in

over charging which is dangerous. The battery cannot

be charged at a temperature higher than 40°C.

The most suitable temperature for charging is that of

20°C–25°C.

35. Do not use the charger continuously.

When one charging is completed, leave the charger for

about 15 minutes before the next charging of battery.

36. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

37. Never disassemble the rechargeable battery and

charger.

38. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to

the battery.

8

English

39. Do not dispose of the battery in ﬁ re. If the battery is

burnt, it may explode.

40. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use. Do not dispose of

the exhausted battery.

41. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or inﬂ ammables into

the charger air ventilation slots will result in electrical

shock hazard or damaged charger.

42. Make sure that the battery is installed ﬁ rmly. If it is at all

loose it could come oﬀ and cause an accident.

43. Never touch moving parts.

Never place your hands, ﬁ ngers or other body parts

near the compressor’s moving parts.

44. Do not use the product if the compressor or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

45. Keep the compressor’s terminals (battery mount) free

of swarf and dust.

○ Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○ During use, try to avoid swarf or dust on the compressor

from falling on the battery.

○ When suspending operation or after use, do not leave

the compressor in an area where it may be exposed to

falling swarf or dust.

Doing so could cause a short circuit that could result in

smoke emission or ignition.

46. Always use the compressor and battery at temperatures

between 0°C and 40°C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall

on the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven, dryer,

or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove

it from the equipment or battery charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible and

ﬂ ammable items. Corrosive gas atmospheres must be

avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the ﬁ rst time, do not use and return it to your

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of

lithium ion battery, the battery may be shorted, causing

ﬁ re. When storing the lithium ion battery, obey surely the

rules of following contents.

○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing

until the ventilator is not seen.

9

English

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will require

special application procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

○ If the BSL36B18 is installed in the power tool, the power

output will exceed 100 Wh and the unit will be classiﬁ ed

as Dangerous Goods for freight classiﬁ cation.

Wh

Power Output

2 to 3 digit number

USB DEVICE CONNECTION

PRECAUTIONS (UC18YSL3)

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○ Prior to use, check the connecting USB cable for any

defect or damage.

Using a defective or damaged USB cable can cause

smoke emission or ignition.

○ When the product is not being used, cover the USB

port with the rubber cover.

Buildup of dust etc. in the USB port can cause smoke

emission or ignition.

NOTE

○ There may be an occasional pause during USB

recharging.

○ When a USB device is not being charged, remove the

USB device from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

○ It may not be possible to charge some USB devices,

depending on the type of device.

○ Charging a USB device from an electrical outlet

(Fig. 7-a)

○ Charging a USB device and battery from an electrical

outlet (Fig. 7-b)

○ How to recharge USB device (Fig. 8)

○ When charging of USB device is completed (Fig. 9)

NAMES OF PARTS (Fig. 1–Fig. 13)

Handle

Regulator pressure gauge

Electric motor & air compressor pump

Quick coupler

Tank

Rubber foot

Drain valve

Power switch (Pressure switch inside)

Pressure regulator knob

Tank pressure gauge

Safety valve

Intake ﬁ lter

Intake ﬁ lter body

Filter element

Protrusions (× 3)

Grooves (× 3)

Battery

Latch

Head cover

Charger indicator lamp

Battery level indicator switch

Battery level indicator lamp

Display panel

Pneumatic tool (not included)

Male quick-connect plug

Air hose with quick coupler ﬁ tting (not included)

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

EC36DA: Cordless Air Compressor

To reduce the risk of injury, user must read

instruction manual.

Always wear eye protection.

10

English

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow it to

fully cool down.

Blinks ;

Output suspended due to failure or

malfunction. The problem may be the battery

so please contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains

the accessories listed on page 318.

Standard accessories are subject to change without

notice.

SPECIFICATIONS

1. Cordless Air Compressor

Model EC36DA

Motor Brushless DC

Voltage 36 V

Tank Capacity 7.3 Itr (1.9 gal.)

Maximum Pressure 9.3 bar (135 PSI)

Free Air

Delivery

at 2.8 bar

(40 PSI) 65.1 ltr/min (2.3 CFM)

at 6.2 bar

(90 PSI) 45.3 ltr/min (1.6 CFM)

Lubrication Oil-less

Battery available for this

tool* Multi volt battery

Weight** 14.3 kg (31.5 Ibs)

(BSL36B18 attached)

* Existing batteries (BSL3660/3626/3620, BSL18xx and

BSL14xx series, etc.) cannot be used with this tool.

** According to EPTA-Procedure 01/2014

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

2. Battery Charger (sold separately)

Model UC18YSL3

Input power source Single phase:

AC 120 V 60 Hz

Charging time

(At a temperature of 20°C) BSL36B18 : Approx.52 min

Charging voltage DC 14.4–18 V

Charging current DC 8.0 A

Weight 0.6 kg

NOTE

The charging time may vary according to temperature

and power source voltage.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive

2012/19/EU on waste electrical and electronic

equipment and its implementation in

accordance with national law, electric tools

that have reached the end of their life must

be collected separately and returned to an

environmentally compatible recycling facility.

Direct current

VRated voltage

Disconnect the battery

Switching ON

Switching OFF

Warning

Electric shock hazard.

Hearing protection must be worn.

Guaranteed sound power level

Do not open the cock before the air hose is

attached.

Risk of high temperature.

Warning of compressor unit may start without

warning

Do not expose to rain.

Store indoors.

Risk of Bursting

Do not adjust the regulator to result in output

pressure greater than the marked maximum

pressure of the attachment. Do not use at a

pressure greater than the rated maximum

pressure of this compressor.

Battery

Lights ;

The battery remaining power is over 75%

Lights ;

The battery remaining power is 50%–75%.

Lights ;

The battery remaining power is 25%–50%.

Lights ;

The battery remaining power is less than 25%

Blinks ;

The battery remaining power is nearly empty.

Recharge the battery soonest possible.

11

English

3. Battery (sold separately)

Model BSL36A18 BSL36B18

Voltage 36 V / 18 V (Automatic Switching*)

Battery capacity 2.5 Ah / 5.0 Ah 4.0 Ah / 8.0 Ah

(Automatic Switching*)

Available cordless

products** Multi volt series, 18 V product

Available charger Sliding charger for lithium ion

batteries

* The tool itself will automatically switch over.

** Please see our general catalogue for details.

KNOW YOUR AIR COMPRESSOR

Before attempting to use this product, familiarize yourself

with all operating features and safety rules. (Fig. 1)

Oil-free brushless motor

Your air compressor features permanently lubricated

bearings.

Power switch (pressure switch inside)

This switch is used to start or stop the air compressor.

Moving the power switch to the (ON) position will provide

automatic power to the pressure switch which will allow

the motor to start when the tank pressure is below the

factory set cut-in pressure. When in the (ON) position, the

pressure switch stops the motor when the tank pressure

reaches the factory set cut-out pressure. Moving the power

switch to the (OFF) position will remove power from the

motor and stop the air compressor.

Electric motor & air compressor pump

The motor is used to power the pump. The electric motor

has a thermal overload protector. If the motor overheats for

any reason, the thermal overload will cut oﬀ power, thus

preventing the motor from being damaged. Wait until the

motor is cool. Motor resets automatically.

Air compressor pump: to compress air, the piston moves

up and down in the cylinder. On the down stroke, air is

drawn in through the air intake valve while the exhaust

valve remains closed. On the upstroke, air is compressed,

the intake valve closes and compressed air is forced out

through the exhaust valve, into the discharge line, through

the check valve and into the tank.

Safety valve

This valve is designed to prevent system failures by

relieving pressure from the system when the compressed

air reaches a predetermined level. The valve is preset by

the manufacturer and must not be modiﬁ ed in any way.

Drain valve

The drain valve is used to remove moisture from the tank.

Tank pressure gauge

The tank pressure gauge indicates the pressure of the air

in the tank.

Regulator pressure gauge

The current line pressure is displayed on the regulator

pressure gauge. This pressure can be adjusted by rotating

the pressure regulator knob.

Pressure regulator knob

Use the pressure regulator knob to adjust the amount of air

being delivered through the hose.

The air pressure coming from the tank is controlled by the

regulator knob. Turn the pressure regulator knob clockwise

to increase discharge pressure and counterclockwise

to decrease discharge pressure. Follow tool operating

instructions for recommended pressure range.

Tank

The tank is used to store the compressed air.

Quick coupler

The outlet is used to connect the 1/4 in. NPT air hose.

Overload protector

This air compressor is equipped with a thermal overload

device which will turn the air compressor oﬀ automatically,

if the air compressor becomes overheated. If the motor

turns OFF repeatedly, check for the following possible

causes ﬁ rst: The battery is depleted. Lack of proper

ventilation or outside air or room temperature too high.

To reset the air compressor:

(1) Turn the air compressor oﬀ .

(2) Remove the battery and allow the air compressor to

cool for 30 minutes.

(3) Install the battery in the air compressor.

(4) Turn the air compressor on.

ASSEMBLY

1. Unpacking

This product requires assembly.

○ Carefully remove the compressor and any accessories

from the box. Make sure that all items listed in the

packing list are included.

○ Inspect the compressor carefully to make sure no

breakage or damage occurred during shipping.

○ Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

compressor.

2. Packing list

– Air Compressor

– Instructions Manual

– Intake Filter

WARNING

○ If any parts are missing do not operate the compressor

until the missing parts are replaced. Failure to do so

could result in possible serious personal injury.

○ Do not attempt to modify this compressor or create

accessories not recommended for use with this

compressor. Any such alteration or modiﬁ cation is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

3. Attaching the intake ﬁ lter

CAUTION

Do not operate without the intake ﬁ lter.

○ Turn oﬀ the power of the air compressor, and remove

the battery.

○ Turn the intake ﬁ lter counter-clockwise until it stops

and then remove the intake ﬁ lter cap and ﬁ lter element.

(Fig. 2)

○ Firmly screw in the intake ﬁ lter body.

○ After inserting the ﬁ lter element, match the grooves of

the intake ﬁ lter cap with the three protrusions on the

intake ﬁ lter body so that the hose points downward.

Then, turn the intake ﬁ lter cap clockwise until it stops.

12

English

○ Check to see if the intake ﬁ lter cap is loose. If the ﬁ lter

is loose, remove and reinstall the ﬁ lter. (Fig. 3)

4. Attaching hose (sold separetely)

○ Insert the hose into the quick coupler already installed

on the compressor. (Fig. 4)

WARNING

Do not attach any tools to the open end of the hose until

start-up has been completed.

○ Firmly grasp the open end of the hose; hold facing

away from yourself and others.

REMOVAL AND INSTALLATION

METHOD OF BATTERY

○ How to install the battery.

Align the battery with the groove in head cover and slip

it into place.

Always insert it all the way until it locks in place with a

little click. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you. (Fig. 5)

○ How to remove the battery.

Withdraw battery from the head cover while pressing

the latch (2 pcs) of the battery. (Fig. 5)

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the charge indicator lamp will blink in red

(At 1- second intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 6 (on page 3).

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the charge

indicator lamp will light up in green. (See Table 1)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 1, according to the condition of the

charger or the rechargeable battery.

Table 1

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging Blinks

(RED)

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds) Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light

for 1 second. (oﬀ for 1 second) Battery capacity at less than 50%

Blinks

(BLUE)

Lights for 1 second. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds) Battery capacity at less than 80%

Lights

(BLUE) Lights continuously Battery capacity at more than 80%

Charging

complete Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby Blinks

(RED)

Lights for 0.3 seconds. Does not light

for 0.3 seconds. (oﬀ for 0.3 seconds) Battery overheated. Unable to

charge. (Charging will commence

when battery cools)

Charging

impossible Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light

for 0.1 seconds. (oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

13

English

(2) Regarding the temperatures and charging time of the rechargeable battery

The temperatures and charging time will become as shown in Table 2.

Table 2

Charger UC18YSL3

Battery

Type of battery Li-ion

Temperatures at which

the battery can be

recharged 0°C–50°C

Charging voltage V 14.4 18

Charging time,

approx. (At 20°C)

BSL14xx series BSL18xx series Multi volt

series

(4 cells) (8 cells) (5 cells) (10 cells) (10 cells)

min

BSL1415S : 15

BSL1415 : 15

BSL1415X : 15

BSL1420 : 20

BSL1425 : 25

BSL1430C : 30

BSL1430 : 20

BSL1440 : 26

BSL1450 : 32

BSL1460 : 38

BSL1815S : 15

BSL1815 : 15

BSL1815X : 15

BSL1820 : 20

BSL1825 : 25

BSL1830C : 30

BSL1850C : 32

BSL1830 : 20

BSL1840 : 26

BSL1850 : 32

BSL1860 : 38

BSL36A18 : 32

BSL36B18 : 52

USB Charging voltage V 5

Charging current A 2

NOTE

The recharging time may vary according to the ambient temperature and power source voltage.

CAUTION

○ If the battery is charged while it is heated because it

has been left for a long time in a location subject to

direct sunlight or because the battery has just been

used, the charge indicator lamp of the charger lights

for 0.3 seconds, does not light for 0.3 seconds (oﬀ for

0.3 seconds). In such a case, ﬁ rst let the battery cool,

then start charging.

○ When the charge indicator lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about

3 seconds to conﬁ rm that the battery being charged

with UC18YSL3 is taken out, wait for a minimum of

3 seconds before reinserting it to continue charging. If

the battery is reinserted within 3 seconds, the battery

may not be properly charged.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might be

low when using them the ﬁ rst and second time. This is a

temporary phenomenon, and normal time required for

recharging will be restored by recharging the batteries

2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

14

English

ABOUT REMAINING BATTERY

INDICATOR

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light the

indicator lamp. (Fig. 10)

The indicator will shut oﬀ approximately 3 seconds after

the remaining battery indicator switch is pressed.

It is best to use the remaining battery indicator as a

guide since there are slight diﬀ erences such as ambient

temperature and the condition of the battery.

When the battery’s remaining capacity is low, the motor

may stop even if 1 light on the indicator lamp is lit up. This

is not the trouble but the result of protection function. If this

happens, recharge the battery as soon as possible.

NOTE

○ Remaining battery levels may vary between that shown

on the battery and that of a product with its own battery

level function.

○ Do not give a strong shock to the display panel or break

it. It may lead to a trouble.

APPLICATIONS

Air compressors are utilized in a variety of air system

applications.

Match hoses, connectors, air tools, and accessories to the

capabilities of the air compressor.

You may use this compressor for purposes listed below:

○ Operating air powered tools requiring less than

45.3 ltr/min @ 6.2 bar.

○ Powering pneumatic nail guns, inﬂ ating tires,

cleaning / blowing with pressurized air.

WARNING

○ Do not allow familiarity with compressor and tools to

make you careless. Remember that a careless fraction

of a second is suﬃ cient to inﬂ ict serious injury.

○ Always wear safety goggles or safety glasses with

side shields when operating compressor. Failure to do

so could result in objects being thrown into your eyes

resulting in possible serious injury.

CAUTION

Do not use in an environment that is dusty or otherwise

contaminated. Using the air compressor in this type of

environment may cause damage to the unit.

CHECKING THE SAFETY VALVE

Before starting the compressor, rotate the safety valve to

make sure that the safety valve operates smoothly. Do

not use compressor if the safety valve is stuck or does not

operate smoothly. Have defective safety valve replaced by

a HiKOKI authorized service center.

WARNING

○ Drain tank to release air pressure before rotate the

safety valve.

○ Risk of bursting.

If the safety valve does not work properly, over-

pressurization may occur, causing tank rupture or an

explosion.

USING THE AIR COMPRESSOR

○ Temperature

Operating temperatures are between 0°C and 40°C.

CAUTION

Never operate in temperatures below 0°C or above

40°C.

WARNING

Always ensure the power switch is in the OFF (O)

position and the regulator pressure gauge reads zero

before changing air tools or disconnecting the hose

from the air outlet. Failure to do so could result in

possible serious personal injury.

○ Ensure the drain valve is closed. (Fig. 11)

○ Ensure the power switch is in the OFF (O) position and

the battery is removed.

○ Ensure the pressure regulator knob is turned fully

counterclockwise. (Fig. 11)

○ If not already installed, attach the hose to the

compressor.

○ Connect the air powered tools to the air hose by

inserting the male quick-connect plug to the quick-

coupler at the end of the hose. (Fig. 12)

○ Install the battery.

○ Turn the power switch to the ON ( I ) position.

○ Adjustment of outlet pressure

Pull the pressure regulator knob to allow the knob to

rotate. Then, adjust the outlet pressure to the required

level by turning the pressure regulator knob clockwise

to increase the outlet pressure and counterclockwise

to decrease it.

A regulator pressure gauge is provided to show when

the required pressure is reached.

When adjusting the pressure, check and make

sure that a tank pressure gauge for the tank has the

pressure level that is higher than that of the pressure to

be adjusted.

It is also imperative that you make adjustment by slowly

starting up the pressure from the level that is lower than

the pressure to be adjusted.

After adjusting the outlet pressure, push in the pressure

regulator knob to lock the knob and use the tool.

NOTE

Before connecting or disconnecting air tools, turn the

regulator knob counterclockwise to stop the ﬂ ow of air.

○ Following all safety precautions in this manual and the

manufacturer’s instructions in the air tool manual, you

may now use your air-powered tool.

○ If using an inﬂ ation accessory with a quick-connect

ﬁ tting, control the amount of air ﬂ ow with the pressure

regulator knob. Turning the knob fully counterclockwise

will completely stop the ﬂ ow of air.

NOTE

Always use the minimum amount of pressure necessary

for your application. Using a higher pressure than

needed will drain air from the tank more rapidly and

cause the unit to cycle on more frequently.

○ When ﬁ nished, always drain the tank and remove the

battery. Never leave the unit plugged in and/or running

unattended.

15

English

WARNING

Check the air tool manual to ensure the correct air

pressure regulator setting for optimum operation

of your air tools. If you are using an air tool not

originally included in the package contents list (not

necessarily supplied with the air compressor model

you have purchased), your tool may require more air

consumption than this air compressor is designed to

supply.

Always read your air tool owner’s manual to match the

correct air supply to your air tool to avoid damage to the

tool or risk of personal injury.

NOTE

When the compressor is new, it will require a

“break-in” period to reach maximum performance.

The typical break-in period is four discharge cycles of

the battery using the BSL36B18 battery.

DRAINING THE TANK

To help prevent tank corrosion and keep moisture out of

the air used, the tank of the compressor should be drained

daily.

To drain the tank: (Fig. 13)

○ Verify that the compressor is turned oﬀ .

○ Holding the handle, tilt the compressor toward the

drain valve so that it’s set in a lower position.

○ Open the drain valve by rotating it 1/4 turn

counterclockwise.

○ Keep the compressor tilted until all moisture has been

removed.

○ Drain moisture from tank into a suitable container.

NOTE

Condensate is a polluting material and should be

disposed of in compliance with local regulations.

○ If drain valve is clogged, release all air pressure by

pulling the safety valve. Remove and clean valve, then

reinstall.

WARNING

Remove the battery from the air compressor and

release all air from the tank before servicing. Failure to

depressurize tank before attempting to remove valve

may cause serious personal injury.

○ Close the drain valve by rotating it 1/4 turn clockwise.

END OF OPERATION/STORAGE

○ Turn the power switch to the OFF position.

○ Remove the battery.

○ Open the drain valve located at the lower part of the

tank. (Fig. 13) Tank pressure should be below 10 psi

when draining the tank.

WARNING

Risk of bursting. When the tank gets corroded, there is

a risk of breakdown. Water will condense in the tank.

If not drained, water will corrode and weaken the tank

causing a risk of tank rupture. Drain tank daily or after

4 hours of use. The drain contains moisture in the air,

abrasion particles, rust, etc..

To drain tank open valve slowly and tilt compressor to

empty accumulated water. Keep face and eyes away

from drain cock.

○ Air hose should be disconnected from compressor and

hung open ends down to allow any moisture to drain.

○ Compressor and hose should be stored in a cool, dry

place.

TRANSPORT

○ Turn the power switch to the OFF position.

○ Remove the battery.

○ Disconnect the air hose and depressurize the tank.

○ Transport the compressor by holding the handle.

OPERATIONAL CAUTIONS

Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous work may cause the temperature of the unit

to rise, activating the temperature protection circuit and

automatically stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous work, rest the unit for

15 minutes or so when replacing the battery. The

temperature of the motor, switch, etc., will rise if

the work is started again immediately after battery

replacement, eventually resulting in burnout.

MAINTENANCE AND INSPECTION

WARNING

○ Be sure to turned oﬀ the switch and remove the battery

before maintenance and inspection.

○ When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

○ Always wear safety goggles or safety glasses with side

shields during compressor operation or when blowing

dust. If operation is dusty, also wear a dust mask.

○ Always release all pressure, disconnect from power

supply, and allow unit to cool to the touch before

cleaning or making repairs on the air compressor.

1. General maintenance

○ Humidity in the air causes condensation to form in the

tank. This condensation should be drained daily and/or

every hour, using the instructions found in Draining the

Tank.

○ The safety valve automatically releases air if the air

receiver pressure exceeds the preset maximum.

Check the safety valve before each use following the

instructions found in Checking the Safety Valve.

○ Inspect the tank yearly for rust, pin holes, or other

imperfections that could cause it to become unsafe.

○ Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types

of commercial solvents and may be damaged by their

use. Use clean cloths to remove dirt, dust, oil, grease,

etc.

WARNING

Do not at any time let brake ﬂ uids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts.

Chemicals can damage, weaken or destroy plastic

which may result in serious personal injury.

2. Lubrication

All the bearings in this compressor are lubricated with

a suﬃ cient amount of high grade lubricant for the life of

the unit under normal operating conditions. Therefore,

no further lubrication of the bearings is required.

16

English

3. Cleaning the intake ﬁ lter

WARNING

Never clean ﬁ lter element with a ﬂ ammable liquid or

solvent.

Open the intake ﬁ lter once a week and clean the inside of

the intake ﬁ lter and the ﬁ lter element with compressed air.

(Fig. 2)

NOTE

Replace the ﬁ lter element when it becomes dirty.

4. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

5. Disposal of the exhausted battery

WARNING

Do not dispose of the exhausted battery. The battery

must explode if it is incinerated. The battery is

recyclable. At the end of it’s useful life, under various

state and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check with

your local solid waste oﬃ cials for details in your area

for recycling options or proper disposal.

6. Storage

Store the power tool and battery in a place in which

the temperature is less than 40°C and out of reach of

children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 319.

For details regarding each bit type, please contact the

HiKOKI Authorized Service Center.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

17

English

TROUBLESHOOTING

WARNING

○ To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source or remove

the battery from the main body before making any adjustments.

○ All electrical or mechanical repairs should be done only by qualiﬁ ed service technicians. Contact HiKOKI Authorized

Service Center.

1. Cordless Air Compressor

Problem Possible Cause Remedy

The compressor does

not run. Loss of power or overheating.

There is no electrical power being supplied

to compressor or the power switch is in the

OFF position.

Thermal overload open.

The power switch is bad.

Tank is full of air.

Check for proper use of battery.

Check to be sure the battery is installed in

and the power switch is in the ON position.

First remove the battery and wait until it

becomes cool.

Replace the power switch.

Compressor will turn on when tank

pressure drops to cut-in pressure.

The thermal overload

protector cuts out

repeatedly.

A poorly ventilated room is causing the

motor to overheat. Move the compressor to well-ventilated

area.

The air receiver

pressure drops when the

compressor shuts oﬀ .

The connections are loose or leaking

(ﬁ ttings, tubing, etc.).

The drain valve is loose.

The check valve is leaking.

Check all the connections with soapy water

and look for bubbles. Tighten any loose

conections until the leak stops.

Tighten the drain valve.

Take the compressor to a service center.

WARNING

Do not disassemble check valve while

air is in tank - empty the all the air out of

the tank before dissasembly.

There is excessive

moisture in the air

discharge.

There is excessive water in the tank.

The humidity is high. Drain the tank to remove water.

Move the compressor to an area of less

humidity or use an air line ﬁ lter to reduce

moisture discharge in the tank.

Air is leaking from the

compressor. The hose connection is loose or improperly

sealed.

The air hose is broken or damaged.

Ensure connections are sealed with thread

sealing tape and tightened.

Replace the air hose.

The compressor runs

continuously The drain valve is open.

The power switch is defective.

The usage is excessive.

Ensure the drain valve is closed.

Take the compressor to a service center.

Decrease the amount of tool run-time; the

compressor is not large enough to supply

the air requirement of the tool.

The compressor vibrates. The compressor mounting bolts are loose. Tighten mounting bolts.

The air output is lower than

normal. The inlet valves are broken.

The connections are leaking. Take the compressor to a service center.

Apply thread sealing tape to ﬁ tting and

tighten.

Battery cannot be installed Attempting to install a battery other than

that speciﬁ ed for the tool. Please install a multi volt type battery.

18

English

2. Charger

Symptom Possible cause Remedy

The charge indicator lamp

rapidly ﬂ ickers purple, and

battery charging doesn’t

begin.

The battery is not inserted all the way. Insert the battery ﬁ rmly.

There is foreign matter in the battery

terminal or where the battery is attached. Remove the foreign matter.

The charge indicator lamp

blinks red, and battery

charging doesn’t begin.

The battery is not inserted all the way. Insert the battery ﬁ rmly.

The battery is overheated. If left alone, the battery will automatically

begin charging if its temperature

decreases, but this may reduce battery

life. It is recommended that the battery be

cooled in a well-ventilated location away

from direct sunlight before charging it.

Battery usage time is short

even though the battery is

fully charged.

The battery’s life is depleted. Replace the battery with a new one.

The battery takes a long

time to charge. The temperature of the battery, the

charger, or the surrounding environment is

extremely low.

Charge the battery indoors or in another

warmer environment.

The charger’s vents are blocked, causing

its internal components to overheat. Avoid blocking the vents.

The cooling fan is not running. Contact a HiKOKI Authorized Service

Center for repairs.

The USB power lamp

has switched oﬀ and the

USB device has stopped

charging.

The battery’s capacity has become low. Replace the battery with one that has

capacity remaining.

Plug the charger’s power plug into an

electric socket.

USB power lamp does not

switch oﬀ even though the

USB device has ﬁ nished

charging.

The USB power lamp lights up green to

indicate that USB charging is possible. This is not a malfunction.

It is unclear what the

charging status of a USB

device is, or whether its

charging is complete.

The USB power lamp does not switch oﬀ

even when charging is complete. Examine the USB device that is charging to

conﬁ rm its charging status.

Charging of a USB device

pauses midway. The charger was plugged into an electrical

socket while the USB device was being

charged using the battery as the power

source.

This is not a malfunction.

The charger pauses USB charging for

about 5 seconds when it is diﬀ erentiating

between power sources.

A battery was inserted into the charger

while the USB device was being charged

using a power socket as the power source.

Charging of the USB

device pauses midway

when the battery and the

USB device are being

charged at the same time.

The battery has become fully charged. This is not a malfunction.

The charger pauses USB charging for

about 5 seconds while it checks whether

the battery has successfully completed

charging.

Charging of the USB

device doesn’t start when

the battery and the USB

device are being charged

at the same time.

The remaining battery capacity is

extremely low. This is not a malfunction.

When the battery capacity reaches a

certain level, USB charging automatically

begins.

19

Deutsch

(Übersetzung der Original-Gebrauchsanweisung)

f) Falls sich der Betrieb des Elektrowerkzeugs

in feuchter Umgebung nicht vermeiden lässt,

verwenden Sie eine Stromversorgung mit

Fehlerstromschutzeinrichtung (Residual

Current Device, RCD).

Durch den Einsatz einer

Fehlerstromschutzeinrichtung wird das Risiko eines

elektrischen Schlages reduziert.

3) Persönliche Sicherheit

a) Bleiben Sie wachsam, achten Sie auf das, was

Sie tun, und setzen Sie Ihren Verstand ein, wenn

Sie mit Elektrowerkzeugen arbeiten.

Benutzen Sie keine Elektrowerkzeuge, wenn

Sie müde sind oder unter Einﬂ uss von Drogen,

Alkohol oder Medikamenten stehen.

Bei der Arbeit mit Elektrowerkzeugen können bereits

kurze Phasen der Unaufmerksamkeit zu schweren

Verletzungen führen.

b) Benutzen Sie eine persönliche

Schutzausrüstung. Tragen Sie immer einen

Augenschutz.

Schutzausrüstung wie Staubmaske, rutschfeste

Sicherheitsschuhe, Schutzhelm und Gehörschutz

senken bei angemessenem Einsatz das

Verletzungsrisiko.

c) Vermeiden Sie unbeabsichtigtes Einschalten.

Achten Sie darauf, dass sich der Schalter

in der Aus- (Oﬀ -) Position beﬁ ndet, ehe Sie

das Gerät mit der Stromversorgung und/

oder Batteriestromversorgung verbinden, es

aufheben oder herumtragen.

Das Herumtragen von Elektrowerkzeugen mit

dem Finger am Schalter oder das Herstellen der

Stromversorgung bei betätigtem Schalter zieht

Unfälle regelrecht an.

d) Entfernen Sie sämtliche Einstellwerkzeuge

(Einstellschlüssel), ehe Sie das Elektrowerkzeug

einschalten.

Ein an einem beweglichen Teil des Elektrowerkzeugs

angebrachter Schlüssel kann zu Verletzungen

führen.

e) Überstrecken Sie sich nicht. Achten Sie jederzeit

darauf, sicher zu stehen und das Gleichgewicht

zu bewahren.

Dadurch haben Sie das Elektrowerkzeug in

unerwarteten Situationen besser im Griﬀ .

f) Tragen Sie geeignete Kleidung. Tragen Sie

keine lose Kleidung oder Schmuck. Halten Sie

Ihr Haar und Ihre Kleidung von beweglichen

Teilen fern.

Lose Kleidung, Schmuck oder langes Haar kann von

beweglichen Teilen erfasst werden.

g) Wenn Anschlüsse für Staubabsaug- und -

sammelvorrichtungen vorhanden sind, sorgen

Sie dafür, dass diese richtig angeschlossen und

eingesetzt werden.

Durch Entfernen des Staubes können

staubbezogene Gefahren vermindert werden.

h) Lassen Sie es nicht zu, dass die durch häuﬁ gen

Gebrauch von Werkzeugen erworbene

Vertrautheit Sie nachlässig macht und Sie

die Sicherheitsrichtlinien für das Werkzeug

ignorieren.

Eine unvorsichtige Handlung kann in

Sekundenbruchteilen zu schweren Verletzungen

führen.

ALLGEMEINE

SICHERHEITSHINWEISE FÜR

ELEKTROGERÄTE

WARNUNG

Bitte beachten Sie sämtliche mit diesem Elektrogerät

gelieferten Sicherheitshinweise, Anweisungen,

Illustrationen und technischen Angaben.

Wenn die nachfolgenden Anweisungen nicht befolgt

werden, kann es zu Stromschlag, Brand und/oder

ernsthaften Verletzungen kommen.

Bitte bewahren Sie alle Warnhinweise und

Anweisungen zum späteren Nachschlagen auf.

Der Begriﬀ „Elektrowerkzeug“ bezieht sich in den

Warnhinweisen auf Elektrowerkzeuge mit Netz-

(schnurgebunden) oder Akkubetrieb (schnurlos).

1) Sicherheit im Arbeitsbereich

a) Sorgen Sie für einen sauberen und gut

ausgeleuchteten Arbeitsbereich.

Zugestellte oder dunkle Bereiche ziehen Unfälle

förmlich an.

b) Verwenden Sie Elektrowerkzeuge niemals an

Orten, an denen Explosionsgefahr besteht,

wie zum Beispiel in der Nähe von leicht

entﬂ ammbaren Flüssigkeiten, Gasen oder

Stäuben.

Bei der Arbeit mit Elektrowerkzeugen kann es zu

Funkenbildung kommen, wodurch sich Stäube oder

Dämpfe entzünden können.

c) Sorgen Sie bei der Arbeit mit Elektrowerkzeugen

dafür, dass sich keine Zuschauer (insbesondere

Kinder) in der Nähe beﬁ nden.

Wenn Sie abgelenkt werden, können Sie die

Kontrolle über das Werkzeug verlieren.

2) Elektrische Sicherheit

a) Elektrowerkzeuge müssen mit passender

Stromversorgung betrieben werden. Nehmen

Sie niemals irgendwelche Änderungen am

Anschlussstecker vor. Verwenden Sie bei

Elektrowerkzeugen mit Schutzkontakt (geerdet)

niemals Adapterstecker.

Stecker im Originalzustand und passende

Steckdosen reduzieren das Stromschlagrisiko.

b) Vermeiden Sie Körperkontakt mit geerdeten

Gegenständen wie Rohrleitungen, Heizungen,

Herden oder Kühlschränken.

Bei Körperkontakt mit geerdeten Gegenständen

besteht ein erhöhtes Stromschlagrisiko.

c) Setzen Sie Elektrowerkzeuge niemals Regen

oder sonstiger Feuchtigkeit aus.

Wenn Flüssigkeiten in ein Elektrowerkzeug

eindringen, erhöht sich das Stromschlagrisiko.

d) Verwenden Sie das Anschlusskabel nicht

missbräuchlich. Tragen Sie das Elektrowerkzeug

niemals am Stromkabel, ziehen Sie es nicht

damit heran und ziehen Sie den Stecker nicht

am Anschlusskabel aus der Steckdose.

Halten Sie das Anschlusskabel von Hitzequellen,

Öl, scharfen Kanten und beweglichen Teilen

fern.

Beschädigte oder verdrehte Anschlusskabel

erhöhen das Stromschlagrisiko.

e) Verwenden Sie, wenn Sie ein Elektrowerkzeug

im Freien benutzen, ein für den Außeneinsatz

geeignetes Verlängerungskabel.

Ein für den Außeneinsatz geeignetes Kabel

vermindert das Stromschlagrisiko.

20

Deutsch

4) Einsatz und Pﬂ ege von Elektrowerkzeugen

a) Überbeanspruchen Sie Elektrowerkzeuge nicht.

Benutzen Sie das richtige Elektrowerkzeug für

Ihren Einsatzzweck.

Das richtige Elektrowerkzeug erledigt seine Arbeit

bei bestimmungsgemäßem Einsatz besser und

sicherer.

b) Benutzen Sie das Elektrowerkzeug nicht, wenn

es sich nicht am Schalter ein- und ausschalten

lässt.

Jedes Elektrowerkzeug, das nicht mit dem Schalter

betätigt werden kann, stellt eine Gefahr dar und

muss repariert werden.

c) Ziehen Sie den Stecker der Stromversorgung

ab und/oder entfernen Sie den Akkupack

vom Elektrowerkzeug, falls abnehmbar, ehe

Sie Einstellarbeiten vornehmen, Zubehörteile

tauschen oder das Elektrowerkzeug verstauen.

Solche präventiven Sicherheitsmaßnahmen

verhindern den unbeabsichtigten Anlauf des

Elektrowerkzeugs und die damit verbundenen

Gefahren.

d) Lagern Sie nicht benutzte Elektrowerkzeuge

außerhalb der Reichweite von Kindern,

lassen Sie nicht zu, dass Personen das

Elektrowerkzeug bedienen, die nicht mit dem

Werkzeug selbst und/oder diesen Anweisungen

vertraut sind.

Elektrowerkzeuge in ungeschulten Händen sind

gefährlich.

e) Wartung von Elektrowerkzeugen und Zubehör.

Prüfen Sie sie auf Fehlausrichtungen,

Leichtgängigkeit beweglicher Teile,

Beschädigungen von Teilen und auf alle

anderen Umstände, die sich auf den Betrieb des

Elektrowerkzeugs auswirken können. Lassen

Sie das Elektrowerkzeug bei Beschädigungen

reparieren, ehe Sie es benutzen.

Viele Unfälle mit Elektrowerkzeugen sind auf

schlechte Wartung zurückzuführen.

f) Halten Sie Schneidwerkzeuge scharf und

sauber.

Richtig gewartete Schneidwerkzeuge mit scharfen

Schneiden bleiben weniger häuﬁ g hängen und sind

einfacher zu beherrschen.

g) Benutzen Sie Elektrowerkzeuge, Zubehör,

Werkzeugspitzen und Ähnliches in

Übereinstimmung mit diesen Anweisungen

– beachten Sie dabei die jeweiligen

Arbeitsbedingungen und die Art der

auszuführenden Arbeiten.

Der Gebrauch des Elektrowerkzeugs für andere

als die vorgesehenen Anwendungen kann zu

gefährlichen Situationen führen.

h) Halten Sie Handgriﬀ e und Greiﬄ ächen trocken,

sauber und frei von Öl und Fett.

Rutschige Handgriﬀ e und Greiﬄ ächen lassen keine

sichere Handhabung und Kontrolle des Werkzeugs

in unerwarteten Situationen zu.

5) Verwendung und Pﬂ ege der Batterie

a) Laden Sie das Gerät nur mit dem vom Hersteller

empfohlenen Ladegerät auf.

Ein Ladegerät für einen speziellen Batterietyp

kann bei Verwendung mit anderen Batterien zu

Brandgefahr führen.

b) Verwenden Sie nur die für das Elektrowerkzeug

speziell empfohlenen Akkus.

Eine Verwendung von anderen Batterien kann zu

Verletzungen und Bränden führen.

c) Ist der Akku nicht in Gebrauch, achten Sie

darauf, dass er nicht mit Metallgegenständen,

beispielsweise Büroklammern, Münzen,

Schlüsseln, Nägeln, Schrauben oder anderen

kleinen Metallgegenständen in Kontakt kommt,

da diese Gegenstände einen Kurzschluss der

Anschlüsse verursachen können.

Ein Kurzschluss der Batterieanschlüsse kann zu

Verbrennungen oder Bränden führen.

d) Im Falle von missbräuchlichen Bedingungen

kann Flüssigkeit aus dem Akku austreten.

Vermeiden Sie in diesem Fall jeglichen Kontakt.

Sollten Sie dennoch mit der Batterieﬂ üssigkeit in

Berührung kommen, waschen Sie die betroﬀ ene

Stelle gründlich mit Wasser ab. Ist die Flüssigkeit

ins Auge geraten, suchen Sie einen Arzt auf.

Ausgetretene Batterieﬂ üssigkeiten können zu

Reizungen oder Verbrennungen führen.

e) Verwenden Sie keinen Akku oder kein Werkzeug,

der oder das beschädigt oder verändert ist.

Beschädigte oder veränderte Akkus können ein

unvorhersehbares Verhalten aufweisen, das zu

einem Feuer, einer Explosion oder Verletzung führen

kann.

f) Setzen Sie den Akku oder das Werkzeug keinem

Feuer oder keiner zu hohen Temperatur aus.

Die Einwirkung von Feuer oder einer Temperatur

über 130°C kann zu einer Explosion führen.

g) Befolgen Sie alle Anweisungen zum Auﬂ aden

und laden Sie den Akku oder das Werkzeug

nicht außerhalb des Temperarturbereichs auf,

der in der Anleitung angegeben ist.

Wenn Sie den Akku falsch oder bei Temperaturen

außerhalb des angegebenen Bereichs auﬂ aden,

kann der Akku beschädigt werden und die Gefahr

eines Brandes steigen.

6) Service

a) Lassen Sie Ihr Elektrowerkzeug durch

qualiﬁ zierte Fachkräfte und nur unter Einsatz

der passenden Originalersatzteile warten.

Dies sorgt dafür, dass die Sicherheit des

Elektrowerkzeugs nicht beeinträchtigt wird.

b) Warten Sie niemals beschädigte Akkus.

Die Wartung von Akkus ist stets vom Hersteller oder

autorisierten Dienstleistern durchzuführen.

VORSICHT

Von Kindern und gebrechlichen Personen fernhalten.

Werkzeuge sollten bei Nichtgebrauch außerhalb der

Reichweite von Kindern und gebrechlichen Personen

aufbewahrt werden.

SICHERHEITSHINWEISE FÜR AKKU

KOMPRESSOR

1. Den Kompressor keinem Regen aussetzen.

Betreiben Sie den Kompressor niemals an feuchten

oder nassen Orten.

2. Kompressor abtrennen.

Trennen Sie den Kompressor stets vom Akku ab und

entfernen Sie die Druckluft aus dem Tank, bevor Sie

irgendwelche Teile warten, überprüfen, reinigen, oder

ersetzen.

3. Unbeabsichtigtes Einschalten vermeiden.

Transportieren Sie den Kompressor nicht, während er

an seinen Akku angeschlossen ist oder wenn der Tank

mit Druckluft gefüllt ist. Achten Sie darauf, dass sich der

Netzschalter in der Stellung „OFF“ beﬁ ndet, bevor Sie

den Kompressor an seinen Akku anschließen.

Pagina se încarcă...

Hikoki EC36DA Manual de utilizare

Hikoki EC36DA Manual de utilizare

în alte limbi

Lucrări înrudite

Alte documente