Eaton HVLD-2L-CGL Installation Instructions Manual

LVLD

MVLD

HVLD

Read these instructions carefully before

attempting a conversion or installation.

Keep these instructions for future

reference.

Installation Instructions

Conversion Kit LED

Table of Contents

Installation Instructions

Wiring ............................................ 4

Test options ................................... 4

Dimensions ....................................5

Telecommand ................................ 5

Indicating LED messages ..............5

Installation Instructions...................6

Denition of order codes ................6

Technical Specications ..................6

Standards ....................................... 6

Overview ........................................6

Preparation .....................................7

Component Layout Guidelines ....... 7

General Wiring Guidelines .............. 7

Terminal Connections ..................... 8

Testing the Conversion ................... 8

Commissioning & Routine Testing ..9

Batteries .........................................9

Output Current / Voltage

characteristics ............................... 10

Output Current / Voltage

diagrams ....................................... 12

Languages

English ............................................6

Croatian ........................................ 18

Czech ............................................ 22

Dutch ............................................ 26

French ........................................... 30

German .........................................34

Greek ............................................38

Hungarian .....................................42

Italian ............................................ 46

Portuguese ................................... 50

Romanian ......................................54

Serbian..........................................58

Slovenian ...................................... 62

Spanish .........................................66

SAFETY INSTRUCTIONS

• The device shall only be used for its

intended purpose and in undamaged

and awless condition.

• Only genuine Eaton spare parts may

be used for replacement and repair.

• Observe the national safety rules

and regulations to prevent accidents

as well as the safety instructions

included in these instruction leaet.

Conversion kit LED

4

CGL+

6

4

5

3

1

2

8

7

IN +

LED R

LED B

1h:

3h:

CV 12V:

CGLine+ Bus

OUT +

OUT -

IN -

Red

Brown

Indicating

Bicolor LED

CGL+

6

4

5

3

1

2

8

7

IN +

LED Y

LED W

1h:

3h:

CV 12V:

DALI Bus

OUT +

OUT -

IN -

White

Yellow

DALI

Indicating

Bicolor LED

DALI

LE D

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

-

+

9Vdc

Telecommand

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

est by Normally Closed Switch

NC

Test options

6

4

5

3

1

2

8

7

IN +

LED

1h:

3h:

CV 12V:

Bus

OUT +

OUT -

IN -

Brown/White

Red/Yellow

NC

CGL+/DALI

Indicating

Bicolor LED

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

230Vac

-

+

9Vdc

Test by Telecommand

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

230Vac

Test by Normally Closed Switch

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

230Vac

Test by Normally Open Switch

NC

NO

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

0Vac

Emergency to Rest by Telecommand

Telecommand Signal

-

+

9Vdc

=

TL A-

TL B+

-

+

9Vdc

=

TL A-

TL B+

Emergency

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

0Vac

Telecommand Signal

Rest

6

4

5

3

1

2

8

7

IN +

LED

1h:

3h:

CV 12V:

Bus

OUT +

OUT -

IN -

Red/White

Brown/Yellow

NC

Test by Normally Closed Switch

CGL+/DALI

Indicating

Bicolor LED

Test options

Telecommand

Replacement

Contact sales with the unit or the battery order code

Fixing centers

4AA 100 (140) 30 (34) 15 (20) (125)

3Cs 130 (160) 25 (26) 25 (26) (150)

4Cs 173 (203) 25 (26) 25 (26) (193)

5Cs 215 (245) 25 (26) 25 (26) (235)

3D 182 (225) 34 (35) 34 (35) (210)

4D 242 (285) 34 (35) 34 (35) (270)

LifePo4 134 (173) 31 (32) 31 (32) (157)

Type L W H

Values inside parentheses refer to batteries with mounting caps.

Self test sequence CGL+ @installation

Lamp

Battery

1 week +12h 1 week 1 week 1 week

1 week +12h @ EVEN

2 weeks +12h @ ODD

26 weeks 26 weeks

Self test sequence CGL+ @operation

Lamp

Battery

1 week 1 week 1 week

26 weeks @ EVEN

27 weeks @ ODD

CGL+, Bi-color LED

Test

Green:

Yellow:

2 sec

0,5 sec

(Green/Yellow)

DALI, Bi-color LED

Test

Green:

Red:

2 sec

0,5 sec

(Green/Red)

Self-contained,

Green:

Green LED

+7

days

×

ODD

EVEN

Indicating LED

6

4

5

3

1

2

8

7

LED

6

4

5

3

1

2

8

7

LED

Indicating LED

Wiring

Test options

5

www.eaton.com

CGL+

6

4

5

3

1

2

8

7

IN +

LED R

LED B

1h:

3h:

CV 12V:

CGLine+ Bus

OUT +

OUT -

IN -

Red

Brown

Indicating

Bicolor LED

CGL+

6

4

5

3

1

2

8

7

IN +

LED Y

LED W

1h:

3h:

CV 12V:

DALI Bus

OUT +

OUT -

IN -

White

Yellow

DALI

Indicating

Bicolor LED

DALI

LE D

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

-

+

9Vdc

Telecommand

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

est by Normally Closed Switch

NC

Test options

6

4

5

3

1

2

8

7

IN +

LED

1h:

3h:

CV 12V:

Bus

OUT +

OUT -

IN -

Brown/White

Red/Yellow

NC

CGL+/DALI

Indicating

Bicolor LED

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

230Vac

-

+

9Vdc

Test by Telecommand

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

230Vac

Test by Normally Closed Switch

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

230Vac

Test by Normally Open Switch

NC

NO

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

0Vac

Emergency to Rest by

Telecommand

Telecommand Signal

-

+

9Vdc

=

TL A-

TL B+

-

+

9Vdc

=

TL A-

TL B+

Emergency

6

4

5

3

1

2

8

7

LED Y

LED W

TL B+

TL A-

IN -

OUT -

OUT +

IN +

0Vac

Telecommand Signal

Rest

6

4

5

3

1

2

8

7

IN +

LED

1h:

3h:

CV 12V:

Bus

OUT +

OUT -

IN -

Red/White

Brown/Yellow

NC

Test by Normally Closed Switch

CGL+/DALI

Indicating

Bicolor LED

Test options

Telecommand

Replacement

Contact sales with the unit or the battery order code

Fixing centers

4AA 100 (140) 30 (34) 15 (20) (125)

3Cs 130 (160) 25 (26) 25 (26) (150)

4Cs 173 (203) 25 (26) 25 (26) (193)

5Cs 215 (245) 25 (26) 25 (26) (235)

3D 182 (225) 34 (35) 34 (35) (210)

4D 242 (285) 34 (35) 34 (35) (270)

LifePo4 134 (173) 31 (32) 31 (32) (157)

Type L W H

Values inside parentheses refer to batteries with mounting caps.

Self test sequence CGL+ @installation

Lamp

Battery

1 week +12h 1 week 1 week 1 week

1 week +12h @ EVEN

2 weeks +12h @ ODD

26 weeks 26 weeks

Self test sequence CGL+ @operation

Lamp

Battery

1 week 1 week 1 week

26 weeks @ EVEN

27 weeks @ ODD

CGL+, Bi-color LED

Test

Green:

Yellow:

2 sec

0,5 sec

(Green/Yellow)

DALI, Bi-color LED

Test

Green:

Red:

2 sec

0,5 sec

(Green/Red)

Self-contained,

Green:

Green LED

+7

days

×

ODD

EVEN

Indicating LED

6

4

5

3

1

2

8

7

LED

6

4

5

3

1

2

8

7

LED

Indicating LED

Telecommand

Dimensions

Battery Dimensions (in mm)

Conversion Kit LED Dimensions

Indicating LED messages

Conversion kit LED

6

DEFINITION OF ORDER CODES:

Indicating LED Cable:

__ : having indicating LED only

TB: having indicating LED and NC Test Button

Remote connection:

_: Telecommand

CGL: Connection for CGL+ bus

D: Connection for DALI bus

Battery cell number / size:

4AA: NiCd AA/0.8Ah

xCS: NiCd CS/1.7Ah (3 or 4 or 5)

xD: NiCd VTD/4Ah (3 or 4)

2L: LiFePo4/3.2Ah

Converter output voltage range:

L: Low voltage range 3..33Vdc (SELV)

M: Medium voltage range 20..55Vdc (SELV)

H: High voltage range 40-180Vdc

TECHNICAL SPECIFICATIONS:

System Mode Non-Maintained

Mains input voltage 230 V AC ±5% (218,5 - 241,5 V AC)

Mains frequency 50/60Hz

Mains Consumption 20mA AC max @ AA & L cell battery

30mA AC max @ CS & D cell battery

Power factor 0,47

Recharge period 24 hours / 16 hours on 2h variants

*on LiFePo variants charging temperature

range is between 0

o

C..50

o

C

(battery protection)

Charging monitor Green LED with cable 1m

Bi-color LED (Green/Yellow)

with cable 1m - CGL+

Bi-color LED (Green/Red) with

cable 1m - DALI

Test facility by Normally Closed Push button

by Normally Open Push button*

by Telecommand signal*

*not applicable on CGL+/DALI variants

Duration 1 or 3h, selectable by jumper,

2h/3h only variants available

Ambient temperature

range (t

a

) 5..40°C / 5..50°C (LiFePo)

Case temperature max (t

c

) converter: 60°C battery: 50°C

IP rating 20

Overheating protection 110°C

Short circuit protection Non-inherently short circuit proof

Weight 125gr

STANDARDS:

Complies with: EN 61347-1, EN 61347-2-7,

EN 55015, EN 61547, EN 61000-3-2

According to: EN 60598-2-22,

EN 61347-2-13, RoHS

OVERVIEW

Conversion kits allow your existing tting to provide

up to 3 hours of emergency lighting in the event

of a power failure. They are easily installed within

the existing tting or in specially designed external

mounting enclosures. The kits are available for LED

lamps operating on the range of 3 to 180Vdc.

PREPARATION

Before using the converter, plan you conversion

carefully, read this leaet and follow the instructions

given in order to comply with current legislation. It is

Installation Instructions

7

www.eaton.com

EN

also recommended to follow the requirements of

ICEL 1004:2003.

In most cases, installation of a conversion kit will

invalidate the manufacturers guarantee and it is

the responsibility of the installer to comply with

the CE marking, Low Voltage and EMC directives.

If a previously installed light tting is to be

converted, any components showing signs

of degradation should be replaced. It is also

recommended that all internal wiring should be

renewed using high temperature (105°C) PVC

cable or the type originally specied if it has a

higher rating.

COMPONENT LAYOUT GUIDELINES

The conversion kits are best installed inside the

light tting, usually requiring the repositioning

of existing components (i.e. ballast and terminal

blocks). When installing inside the tting:

• Do not obstruct cable entries, mounting

facilities, lighting controllers or covers.

• Do not locate the batteries or capacitor near

excessive heat sources, e.g. ballasts and

lamp ends.

• The module should be placed as close as

possible to the ballast to keep wires short,

while being far enough away to prevent

overheating.

• Ensure your layout doesn’t interfere with

the essential safety features of the tting

such as shrouding, earthing etc.

• Avoid altering the tting’s normal lighting

distribution.

Space & temperature restrictions may require

remote mounting of the batteries or the complete

conversion kit in a special enclosure. If this

is necessary, it is not as important to take into

account the component temperatures but you

should note the following:

• The cable to the fully remote enclosure

must not exceed 2m.

• If mounted more than 1m from the light

tting, the remote enclosure must be

connected using re proof cable.

• Battery leads must be as short as possible,

and the total resistance of the battery lead

must not exceed 0,05 ohms.

• The indicating LED should be mounted

within the light tting or remote enclosure

where it is clearly visible during normal

operation (mounting requires 0.25” or

6,35mm hole).

GENERAL WIRING GUIDELINES

Refer to the diagrams for typical wiring

connections and observe the following guidelines:

• Always use high temperature 105°C PVC

cable (or a higher grade if originally used in

Conversion kit LED

8

the light tting).

• All metal work within an earthed tting

MUST be securely earthed, including

reectors and louvers.

• Keep cables as short as possible.

• Mains wiring must exit tting from nearest

entry/exit point.

• Keep mains wiring away from the LED lamp

cables for better EMC performance.

• In SELV conversion applications keep

mains wiring separated from the battery,

LED lamp and indicating LED wiring or use

special (double insulated) wiring.

TERMINAL CONNECTIONS

• Connect the neutral to ‘N’ terminal of the

converter and to the mains LED driver neutral

input terminal. Connect the unswitched

live to terminal ‘L’ and the switched live in

terminal ‘L1 In’ on the converter. Connect

converter’s ‘L1 OUT’ terminal to the mains

LED driver live input terminal.

• Connect the yellow/white or red/brown LED

wire to the terminal marked ‘LED Y’/'LED

W' or 'LED R'/'LED B' respectively.

• Connect the two cables for the telelcommand

signal on the '-A'/'+B' terminal blocks

(polarity sensitive connection). Connect the

two cables from CGL+ or Dali bus on the

'CGL+' or 'Dali' terminal blocks respectively

(polarity free connection).

• Ensure the light tting is securely earthed

Note: Make sure that the terminals on the module

cannot be touched when changing the lamp or

starter by shrouding them with earthed metal or

thermoplastic insulation.

TESTING THE CONVERSION

Electrical Tests

Earth Continuity: Earth resistance between earth

terminal and all metal parts must be less than 0,5

ohms at 10 Amps.

Electrical Strength: Ensure that there is no

breakdown when use 1500V ac (50/60Hz) test

voltage between the Neutral and Live bonded

together and the Earth terminal.

Testing an Installed Fitting:

• Connect mains voltage to the unswitched

live supply and ensure that the LED is lit.

• Connect mains voltage to the switched and

unswitched live supplies and check that the

lamp lights correctly.

• Apply mains supply to the unswitched live

for a minimum of 10 min. Disconnect the

supply and check that the emergency lamp

lights.

• It is recommended that a full duration test is

carried out by applying the mains supply for

9

www.eaton.com

24 hours and ensuring the emergency lamp

operates for the specied duration.

• If any of the above tests fail, repeat them

after a full 24 hour recharge period and

then restore the supply and check the

LED indication to make sure the battery is

charging.

COMMISSIONING & ROUTINE TESTING

When you have completed the conversion, ll in

the date of commissioning in the space provided

on the battery label. The conversion invalidates

any certication (e.g, ENEC / CE safety mark),

therefore all markings must be removed and

replaced with the caution/warning labels supplied.

Note: It is the installer’s responsibility to ensure

the requirements of the CE marking, LV and

EMC directives are met. ICEL 1004:2003 gives

guidelines on this if required.

A routine testing scheme should be dened and

followed, to ensure correct emergency operation

of installed converted luminaries over time.

The types of testing and test frequencies dened,

must comply to any relevant requirements of

regulations and / or directives applicable to the

country of the installation.

BATTERIES

The recharging device provides reinforced

insulation, is protected against short circuit and

can charge the battery normally after the short

circuit is removed. It normally takes 10 minutes

charge to provide 1 minute of discharge power

from the battery. The battery should be replaced

with an original Eaton part when the rated

duration is no longer achieved. The replacement

part number is written on the battery label. Always

use the approved NiCd or LiFePO4 batteries and

store them between 0 and 25°C.

Warning: When disposing of batteries, do not

pierce, incinerate or short circuit them. The

approved batteries contain cadmium and must be

disposed of correctly.

Conversion kit LED

10

Electrical characteristics

Output Current / Voltage characteristics

Battery Cell Type

Battery Cell Number (Cell alignment)

Typical Charge Current (mA dc)

Duration (h)

Typical Output Power (W)

Typical Discharge Current (mA dc)

LED Lamp Voltage Range (V dc)

LED Lamp Max Capacitance (µF)

Constant Voltage (CV) output (V dc)

Open Voltage U-OUT (V dc)

NiCd AA 0,8Ah

4 (2x2)

40

NiCd Cs 1,7Ah

3 (3x1)

95

LVLD LVLD

1

1,75

440

3

0,65

180

1

2,75

950

3

1,1

390

3 ..33 3 ..33

1

12 12

- -

40 (SELV) 40 (SELV)

1

Battery Cell Type

Battery Cell Number (Cell alignment)

Typical Charge Current (mA dc)

Duration (h)

Typical Output Power (W)

Typical Discharge Current (mA dc)

LED Lamp Voltage Range (V dc)

LED Lamp Max Capacitance (µF)

Constant Voltage (CV) output (V dc)

Open Voltage U-OUT (V dc)

NiCd AA 0,8Ah

4 (2x2)

40

NiCd Cs 1,7Ah

4 (4x1)

90

MVLD MVLD

1

1,65

440

3

0,65

180

1

3,4

950

3

1,4

390

20 ..55 20 ..55

1

24 24

- -

60 (SELV) 60 (SELV)

1

Battery Cell Type

Battery Cell Number (Cell alignment)

Typical Charge Current (mA dc)

Duration (h)

Typical Output Power (W)

Typical Discharge Current (mA dc)

LED Lamp Voltage Range (V dc)

LED Lamp Max Capacitance (µF)

Constant Voltage (CV) output (V dc)

Open Voltage U-OUT (V dc)

NiCd AA 0,8Ah

4 (2x2)

40

NiCd Cs 1,7Ah

5 (5x1)

95

HVLD HVLD

1

1,55

440

3

0,6

180

41 ..175

1

4,1

950

3

1,65

390

40 ..180 4 ..180

1

48 48

- -

200 200

1

11

www.eaton.com

NiCd 4D 4Ah

4 (4x1)

180

2

5

1200

3 ..33

1

-

40 (SELV)

NiCd 3D 4Ah

3 (3x1)

180

3

2.75

950

3..33

1 1

-

40 (SELV)

NiCd 4D 4Ah

4 (4x1)

180

3

3,7

950

3 ..33

-

40 (SELV)

LVLD-3DLVLD-4D-TB LVLD-4D

LiFePo4 3,2Ah

2 (2x1)

220 (max)

1

6

1100

3

510

3 ..33

1

12

-

40 (SELV)

LVLD-2L-CGL

or LVLD-2L-D

NiCd 4D 4Ah

4 (4x1)

180

2

4,2

1200

20 ..55

1

-

60 (SELV)

NiCd 4D 4Ah

4 (4x1)

180

3

3,4

950

20 ..55

1

-

60 (SELV)

MVLD-4D-TB

NiCd 3D 4Ah

3 (3x1)

180

3

2,5

950

20 ..55

1

-

60 (SELV)

MVLD-3D MVLD-4D

LiFePo4 3,2Ah

2 (2x1)

220 (max)

1

4,8

950

3

2,4

450

20 ..55

1

24

-

60 (SELV)

MVLD-2L-CGL

or MVLD-2L-D

NiCd 4D 4Ah

4 (4x1)

180

2

4

1100

40 ..180

1

-

200

NiCd 4D 4Ah

4 (4x1)

180

3

3,1

40 ..180

1

-

200

HVLD-4D-TB HVLD-4D

LiFePo4 3,2Ah

2 (2x1)

220 (max)

1

4,2

850

3

2,2

450

40 ..180

1

48

-

200

HVLD-2L-CGL

or HVLD-2L-D

Conversion kit LED

12

LVLD-3CS, 3h

LVLD-4AA, 3h

LVLD-4AA, 1h

LVLD-3CS, 1h

LVLD-3D, 3h

I

LED

[mA]I

LED

[mA]I

LED

[mA]I

LED

[mA]

Output Current / Voltage diagrams

Low Voltage LED Driver

LVLD-2L-CGL, 1h

LVLD-2L-CGL, 3h

LVLD-4D, 3h

LVLD-4D-TB, 2h

LED current at nominal battery voltage and min.

battery dischanrge current

LED current at nominal battery voltage and max.

battery dischanrge current

I

LED

[mA]

I

LED

[mA]I

LED

[mA]

I

LED

[mA]

0

100

200

300

400

500

600

700

800

900

3 6 9 12 15 18 21 24 27 30 33

0

100

200

300

400

500

600

3 6 9 12 15 18 21 24 27 30 33

0

100

200

300

400

500

600

700

800

3 6 9 12 15 18 21 24 27 30 33

0

100

200

300

400

500

600

700

800

3 6 9 12 15 18 21 24 27 30 33

13

www.eaton.com

LVLD-3CS, 3h

LVLD-4AA, 3h

LVLD-4AA, 1h

LVLD-3CS, 1h

LVLD-3D, 3h

I

LED

[mA]I

LED

[mA]I

LED

[mA]I

LED

[mA]

LVLD-2L-CGL, 1h

LVLD-2L-CGL, 3h

LVLD-4D, 3h

LVLD-4D-TB, 2h

LED current at nominal battery voltage and min.

battery dischanrge current

LED current at nominal battery voltage and max.

battery dischanrge current

I

LED

[mA]

I

LED

[mA]I

LED

[mA]

I

LED

[mA]

0

100

200

300

400

500

600

700

800

900

3 6 9 12 15 18 21 24 27 30 33

0

100

200

300

400

500

600

3 6 9 12 15 18 21 24 27 30 33

0

100

200

300

400

500

600

700

800

3 6 9 12 15 18 21 24 27 30 33

0

100

200

300

400

500

600

700

800

3 6 9 12 15 18 21 24 27 30 33

Conversion kit LED

14

MVLD-4CS, 3h

MVLD-4CS, 1h

MVLD-4D, 3h

MVLD-4AA, 1h

MVLD-4AA, 3h

I

LED

[mA]I

LED

[mA]

I

LED

[mA]

I

LED

[mA]

0

20

40

60

80

100

120

140

160

180

200

20 25 30 35 40 45 50 55

MVLD-2L-CGL, 1h

MVLD-2L-CGL, 3h

MVLD-3D, 3h

MVLD-4D-TB, 2h

LED current at nominal battery voltage and min.

battery dischanrge current

LED current at nominal battery voltage and max.

battery dischanrge current

I

LED

[mA]I

LED

[mA]I

LED

[mA]

I

LED

[mA]

0

50

100

150

200

250

300

20 25 30 35 40 45 50 55

0

20

40

60

80

100

120

140

20 25 30 35 40 45 50 55

0

20

40

60

80

100

120

140

20 25 30 35 40 45 50 55

0

50

100

150

200

250

20 25 30 35 40 45 50 55

Output Current / Voltage diagrams

Medium Voltage LED Driver

15

www.eaton.com

MVLD-2L-CGL, 1h

MVLD-2L-CGL, 3h

MVLD-3D, 3h

MVLD-4D-TB, 2h

LED current at nominal battery voltage and min.

battery dischanrge current

LED current at nominal battery voltage and max.

battery dischanrge current

I

LED

[mA]I

LED

[mA]I

LED

[mA]

I

LED

[mA]

0

50

100

150

200

250

300

20 25 30 35 40 45 50 55

0

20

40

60

80

100

120

140

20 25 30 35 40 45 50 55

0

20

40

60

80

100

120

140

20 25 30 35 40 45 50 55

0

50

100

150

200

250

20 25 30 35 40 45 50 55

Conversion kit LED

16

HVLD-5CS, 3h

HVLD-4AA, 3h

HVLD-4AA, 1h

HVLD-5CS, 1h

I

LED

[mA]I

LED

[mA]I

LED

[mA]

I

LED

[mA]

Output Current / Voltage diagrams

High Voltage LED Driver

HVLD-2L-CGL, 1h

HVLD-2L-CGL, 3h

HVLD-4D, 3h

HVLD-4D-TB, 2h

LED current at nominal battery voltage and min.

battery dischanrge current

LED current at nominal battery voltage and max.

battery dischanrge current

I

LED

[mA]I

LED

[mA]I

LED

[mA]I

LED

[mA]

0

20

40

60

80

100

120

40 60 80 100 120 140 160 180

0

10

20

30

40

50

60

40 60 80 100 120 140 160 180

0

10

20

30

40

50

60

70

80

90

40 60 80 100 120 140 160 180

0

20

40

60

80

100

120

40 60 80 100 120 140 160 180

17

www.eaton.com

HVLD-2L-CGL, 1h

HVLD-2L-CGL, 3h

HVLD-4D, 3h

HVLD-4D-TB, 2h

LED current at nominal battery voltage and min.

battery dischanrge current

LED current at nominal battery voltage and max.

battery dischanrge current

I

LED

[mA]I

LED

[mA]I

LED

[mA]I

LED

[mA]

0

20

40

60

80

100

120

40 60 80 100 120 140 160 180

0

10

20

30

40

50

60

40 60 80 100 120 140 160 180

0

10

20

30

40

50

60

70

80

90

40 60 80 100 120 140 160 180

0

20

40

60

80

100

120

40 60 80 100 120 140 160 180

Conversion kit LED

18

DEFINIRANJE KATALOŠKIH BROJEVA

TEHNIČKE SPECIFIKACIJE:

Način rada pripravni spoj

Ulazni napon 230 V AC ±5% (218, 5 - 241,5 V AC)

Frekvencija 50/60Hz

Potrošnja energije 20mA AC max @ AA & L veličina baterije

30mA AC max @ CS & D veličina baterije

Faktor snage 0.47

Period ponovnog punjenja 24 sata / 16 sati na 2h varijanti

* Na LifePo varijanti dozvoljen raspon temperature

punjenja je između : 0°C…50°C ( zaštita baterije )

Kontrolna punjenja LED svetiljkom, sa kablom 1m

Dvobojna LED (Zeleno/Žuta) sa kablom

1m - CGL+

Dvobojna LED (Zeleno/Crvena) sa kablom

1m - DALI

Način testiranja Komandnim signalom*

Normalno zatvorenim tasterom

Normalno otvorenim tasterom*

*nije primjenjivo na CGL+/DALI varijante

Trajanje 1 ili 3h, odabir trajanja autonomije

pomoću kratkospojnika,

2h/3h samo raspoložive varijante

Radna temperatura (t

a

) 5..40°C / 5..50°C (LiFePo)

Maks. temperatura kućišta (t

c

) konvertor: 60°C / baterija: 50°C

IP stupanj zaštite 20

Zaštita od pregrijavanja 110°C

Zaštita od kratkog spoja ne inherentni dokaz kratkog spoja

Težina 125gr

STANDARDI:

U skladu sa: EN 61347-1, EN 61347-2-7,

EN 55015, EN 61547,

EN 61000-3-2

Certicirano prema: EN 60598-2-22,

EN 61347-2-13, RoHS

PREGLED

Komplet za konverziju omogućava da postojeću rasvjetu

pretvorite u rasvjetu za slučaj nužde autonomije do

3 sata u slučaju nestanka električne energije. Lako se

instalira u postojeća kućišta ili u specijalno dizajnirna

kućišta za vanjsku montažu. Kompleti su dostupni za LED

lampe radnog napona od 3 do 180 Vdc.

Uputstvo za Instalaciju

LED Kabl za indikaciju ukljućuje:

__ : posjeduje jedino LED indikaciju

TB: posjeduje LED indikaciju I NC Test taster

Spoj na daljinu:

_: Daljinsko

CGL: Priključak za CGL+ protokol

D: Priključak na DALI protokol

Broj / veličina ćelije baterije:

4AA: NiCd AA/0.8Ah

xCS: NiCd CS/1.7Ah (3 ili 4 ili 5)

xD: NiCd VTD/4Ah (3 ili 4)

2L: LiFePo4/3.2Ah

Izlazni naponski domet konvertora:

L: domet niskog napona 3..33Vdc (SELV)

M: domet srednjeg napona 20..55Vdc (SELV)

H: domet visokog napona 40-180Vdc

19

www.eaton.com

HR

PRIPREMA

Prije upotrebe kompleta za konverziju pažljivo ju

isplanirajte, pročitajte ovo uputstvo i pratite instrukcije

u skladu sa važećim zakonskim propisima. Takođe

je preporučljivo da pratite zahtjeve u skladu sa ICEL

1004:2003.

Garancija proizvođača je nevažeća ukoliko instalater

nije upoznat sa CE certifkatom I EMC direktivama.

Ukoliko planirate konverziju ranije instalirane rasvjete,

prethodno trebate izvršiti zamjenu svih komponenti

koji pokazuju bilo kakve znakove oštećenja. Također

se preporuča zamijeniti sve kablove kablovima visoke

podnošljive temperature (105°C) PVC ili kablovima

orginalno speciﬁciranim ukoliko imaju veću zaštitu.

RASPORED KOMPONENTI

Komplet za konverziju je najbolje instalirati unutar

kućišta rasvjete i uglavnom zahtjeva razmještanje

postojećih komponenti. Kada instalirate unutar kućišta

nemojte remetiti ulaz kablova, opreme za montiranje,

kontrolera osvetljenja i pokriva:

• Nemojte postavljati baterije i kondenzatore

pored direktnog izvora topline.

• Modul bi trebalo pozicionirati što je moguće

bliže balastu kako bi žice bile što kraće, a ujedno

i dovoljno daleko kako bi spriječili pregrijavanje.

• Uvjerite se da raspored ne ometa osnovne

sigurnosne karakteristike.

Ograničenja po pitanju prostora i temperature mogu

zahtjevati izmještanje baterije i kompleta za konverziju

u specijalna kućišta:

• Nije neopohodno uzimati u obzir temperature

komponenti ali treba obratiti pažnju na slijedeće:

kabl do izdvojenog kučišta ne smije biti duži od

2m.

• Ukoliko se montira na udaljenost veću od 1m

kućište mora biti povezano vatrootpornim

kablom.

• Kontakti baterije moraju biti što je moguće kraći i

ukupna otpornost kontakata baterije ne sme biti

veća od 0,5 oma.

• Signalna LED dioda mora biti jasno vidljiva

tokom normalnog rada (montaža zahtjeva rupu

promjera 6,35mm).

UPUTSTVO ZA POVEZIVANJE

Pratite sheme povezivanja i pridržavajte se slijedećih

uputa:

• Uvijek koristite kablove koji mogu izdržati

temperaturu 105°C ili višu klasu.

• Svi metalni dijelovi MORAJU biti uzemljeni.

• Kablovi moraju biti što je moguće kraći.

• Kablovi napajanja moraju izaći iz kućišta na

najbližem izlazu.

• Kablove napajanja držati dalje od LED svetiljke

radi boljih EMC performansi.

• U SELV konverzijskoj aplikaciji držati glavno

Conversion kit LED

20

napajanje odvojeno od baterije, LED lampe

i indikacije LED lampe napajanja ili koristiti

specijalno dvostruko izolirano napajanje.

PRIKLJUČCI

• Povezati nulu na priključak N na konvertoru i na

priključak N na glavnom LED upravljaču. Povezati

direktnu fazu na priključak L a prekinutu fazu

na L1 priključak konvertora. Povezati priključak

L1 konvertorskog izlaza L1 OUT na glavni LED

upravljač ulazni priključak.

• Povežite žuti/bijeli ili crveni/smeđi LED žicu na

klemu identično označenu sa ‘LED Y’/'LED W' ili

'LED R'/'LED B'

• Povežite dva kabla za signal telekomande na

'-A'/'+B' priključne kleme (konekcija osjetljiva na

promjenu polariteta). Povežite dva kabla sa CGL+

ili DALI protokola na 'CGL+' ili 'Dali' priključne

kleme identično označene (konekcija neosjetljiva

na promjenu polariteta).

• Pobrinite se da je sigurno uzemljeno.

Napomena: pobrinite se da se priključci na modulima

ne mogu dodirnuti prilikom zamjene lampe ili startera

obavijajući ih izolacionim materijalom.

ISPITIVANJE KONVERZIJE

Električno testiranje

Neprekidnost uzemljenja: otpornost između

uzemljenog terminala i svih metalnih dijelova mora biti

manja od 0,5 oma na 10 A.

Električna snaga: pobrinite se da nema kvarova pri

1500VAC (50/60Hz) napona između N i L i priključka

uzemljenja.

Testiranje instaliranog osvjetljenja:

• Povežite napajanje i pobrinite se da LED indikator

svjetli. Povežite napajanje na rasvjetu i pobrinite

se da rasvjeta svjetli ispravno.

• Uključite napajanje minimum 10 minuta.

• Isključite napajanje i pobrinite se da lampa za

slučaj nužde svjetli.

• Preporučuje se izvesti test punog trajanja tako

što ćete ostaviti priključen napon 24 sata i nakon

skidanja sa napona lampa u slučaju nužde bi

trebala svjetliti naznačeni vremenski period.

• Ukoliko bilo koji test ne bude prošao u redu

ponovite ga poslije puna 24 sata punjenja i onda

obnovite napajanje i provjerite na LED indikatoru

da li se baterija puni.

PUŠTANJE U RAD I RUTINSKO TESTIRANJE

Kada ste završili konverziju upišite datum puštanja u rad

u prostor predviđen na naljepnici baterije.

Konverzija poništava sve certiﬁkate (Kitemark /

CE), samim tim sve oznake moraju biti uklonjene i

zamijenjene natpisima Oprez/Upozorenje (Caution/

Warning) koje ste dobili u okviru isporuke.

Napomena: odgovornost instalatera je da osigura CE

Pagina se încarcă ...

Eaton HVLD-2L-CGL Installation Instructions Manual

Eaton HVLD-2L-CGL Installation Instructions Manual

în alte limbi

Lucrări conexe

Alte documente