Yamaha ISX-B820 Manual de utilizare

Categorie
CD playere
Tip
Manual de utilizare
INTEGRATED AUDIO SYSTEM
SYSTÈME AUDIO INTÉGRÉ
ISX-B820
G
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
i En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place
– away from direct sunlight, heat sources, vibration, dust,
moisture and cold. For proper ventilation, allow the
following minimum clearances.
Top: 15 cm (6 in)
Rear: 2.5 cm (1 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot (or vice versa), and do not locate this
unit in an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire, damage to
this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
13 To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press to set the system to off,
and disconnect the AC power plug from the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this unit
alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
Keep the batteries in a location out of reach of
children. Batteries can be dangerous if a child were to
put in his or her mouth.
If the batteries grow old, the effective operation range
of the remote control decreases considerably. If this
happens, replace the batteries with two new ones as
soon a
s possible.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as
alkaline and manganese batteries) together. Read the
packaging carefully as these different types of
batteries may have the same shape and color.
Exhausted batteries may leak. If the batteries have
leaked, dispose of them immediately. Avoid touching
the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
If you plan not to use the unit for a long period of
time, remove the batteries from the unit. Otherwise,
the batteries will wear out, possibly resulting in a
leakage of battery liquid that may damage the unit.
Do not throw away batteries with general house
waste. Dispose of them correctly in accordance with
your local regulations.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off by . In this state, this unit is designed
to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a CRT-
based (Braun tube) TV set might impair picture color.
Should this happen, move this unit away from the TV set.
1 En
English Français Deutsch Svenska Italiano Español Nederlands Русский
NAMES OF PARTS AND THEIR FUNCTIONS.........................2
ADJUSTING THE CLOCK.........................................................5
LISTENING TO iPod..................................................................6
LISTENING TO CD AND USB DEVICES..................................7
LISTENING TO MUSIC
FROM YOUR Bluetooth COMPONENT .................................10
LISTENING TO FM STATIONS...............................................12
LISTENING TO EXTERNAL SOURCES .................................13
USING THE ALARM FUNCTION ............................................14
USING THE SLEEP TIMER.....................................................17
TONE CONTROL.....................................................................17
ADJUST BRIGHTNESS OF FRONT PANEL DISPLAY .........17
TROUBLESHOOTING.............................................................18
NOTES ON DISCS AND USB DEVICES.................................21
SPECIFICATIONS ...................................................................22
Play back music on external devices such as iPod/iPhone models, audio/data CDs and USB devices, and tune in to the FM radio.
•By the Bluetooth technology, you can enjoy clear sound without wired connections.
Use your favorite music or set of beeps as an alarm. The music you select is played at a volume of your own choice at the set alarm time,
giving you the best possible start to the day (IntelliAlarm function) ( P. 14 ).
Store/call up to five of your favorite FM stations easily.
The 3-band equalizer (bass, middle, treble) can be set so that music sounds exactly how you want it.
Two types of clocks (with hour hands) that match the design of the unit can be shown.
About this manual
The phrase “iPod” used throughout this manual also includes the “iPhone”.
If both the unit and remote control buttons can be used to operate a feature, the manual will describe steps using the buttons on the unit.
indicates precautions for use of the unit and its feature limitations.
indicates supplementary explanations for better use.
Insert the batteries into the remote control in the correct direction
(+ and –).
Point the remote control at the remote control signal receiver (on
the front panel) and use within the range shown below.
CONTENTS
Features
Supplied accessories
How to use the remote control
Note
y
ISX-B820
Power cable Remote control Dock cover
USB cap
FM antenna
Bracket
Pole
Base
Support
Cable clamp
Screw set
Note
Use these items to assemble the
stand. Read the separate
Assembly Guide for information
on how to assemble the stand.
Note
Keep the USB cap out of
reach of children so as to
ensure that it is not
mistakenly swallowed.
Batteries x 2
(AA, LR6, UM-3)
Owner’s Manual
(this manual)
Assembly Guide
6 m (20')
2 En
a (Power)
Press to turn the system on/off. Time is displayed on the front
panel even when the system is off.
y
Press and hold on the top of the unit for more than 3 seconds to set
the system to power save mode. No information on the front panel is
displayed in power save mode. This can reduce power consumption.
To cancel power save mode, press again.
Even in system off/power save mode, the alarm function is available.
b iPod dock
Connect an iPod.
c USB port
Connect a USB device (P. 9).
d VOLUME/+
Adjust the volume.
e SOURCE
Switch the source to be played.
f ALARM
Turns the alarm on/off, and allows various alarm settings to be
adjusted (P. 15, 16).
g SNOOZE/SLEEP
Set the sleep timer or switch the alarm to snooze mode
(P. 16, 17).
h PRESET
Store/call up FM stations, or switch the playback folder (when
playing music on data CDs or USB devices).
i /
Skip the playback track/file, or tune the radio.
Holding the button down while playing a track/file will search
backward/forward the track/file.
j /
Play/pause the track being played.
k
Eject the CD.
l Disc slot
Insert a CD.
NAMES OF PARTS AND THEIR FUNCTIONS
Top panel
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
12345678 jlk9
Connecting an iPod to the iPod dock
y
An iPod will be recharged while it is connected to the dock. The iPod will not be recharged
when the unit is in power save mode.
Be sure to use a dock adaptor that is compatible with your iPod. If you do not use the adaptor
or the adaptor is not compatible, the connection could be loose or poor, which could cause
damage to the connector. For details on dock adaptor information, please visit official Apples
website.
If an iPod in protective case is connected by force, the connector may be damaged. Remove
the protective case before connection.
When the iPod is not in use, set the iPod dock cover to protect the connector.
Dock adaptor
3 En
NAMES OF PARTS AND THEIR FUNCTIONS
English
1 Play/shuffle/repeat indicator
Displays the playback mode (P. 6, 9).
b Remote control signal receiver
c Clock indicator
Shows the clock hour hand (P. 5).
d Source indicator
Shows selected source.
e Bluetooth indicator
Turns on if this unit is connecting via Bluetooth (P. 10, 11).
f Sleep indicator
Turns on if the sleep timer has been set (P. 17).
g Alarm indicator
Turns on if the alarm has been set (P. 14).
h Multi-function indicator
Displays various information, including the clock time, track
number being played or FM station.
i Illumination sensor
Detects ambient lighting. Do not cover this sensor.
a ALARM TYPE
Switches the alarm type (P. 15).
b CLOCK
Switches the type of clock display or allows the time to be set
(P. 5).
c DIMMER
Adjusts the brightness of the front panel display (P. 17).
d AUX
Connects an external device.
e FM antenna terminal
Connects the supplied FM antenna or an outdoor antenna.
Notes
The antenna should be stretched out. If radio reception is poor, change
the height, direction, or placement of the antenna.
If you use a commercially available outdoor antenna instead of the
supplied FM antenna, reception may be better.
f Terminal cover
Remove the terminal cover before connecting external devices
to AUX, and/or connecting the FM antenna to antenna
terminal.
Front panel display
Rear panel
1
6
2 3
5
4
Supplied
FM antenna
If you pass the outdoor antenna cable and/or external device cable through the pole of the stand, read the separate Assembly Guide.
NAMES OF PARTS AND THEIR FUNCTIONS
4 En
a Remote control signal transmitter
b (Power)
Press to turn the system on/off.
c ALARM
Switches the alarm on/off.
d SNOOZE/SLEEP
Set the sleep timer or switch the alarm to snooze mode
(P. 16, 17).
e Source button
Switch the source to be played.
f FOLDER
Switch the playback folder when playing music on data CDs or
USB devices.
g /
Skip the playback track/file.
Holding the button down while playing a track/file will search
backward/forward the track/file.
h
Play/pause.
i
Stop playback.
j (Repeat)/ (Shuffle)
Play music on an iPod, audio/data CD or USB device in repeat/
shuffle (P. 6, 9).
k EQ LOW/MID/HIGH
Adjust the bass, middle or treble sound quality (P. 17).
l PRESET /
Select a preset FM station.
m MEMORY
Store the FM station (P. 12).
n TUNING /
Tune the radio.
o VOLUME + /
Adjust the volume.
p MUTE
Mute/resume the sound.
Remote control
Bluetooth
1
n
p
o
4
6
j
k
8
9
5
3
2
m
l
7
iPod control buttons
5 En
English
1 Move the CLOCK switch on the rear panel to SET.
2 Set the time with / .
3 Move the CLOCK switch on the rear panel to
CLOCK1 or CLOCK2.
y
Connecting an iPod to the iPod dock in step 2 will copy the time on the
iPod to the unit. If the iPod is already connected to the iPod dock when
CLOCK is set to SET, the time in the iPod will not be copied.
Pressing SNOOZE/SLEEP in step
2 will switch between the 12 and
24 hour clock display.
The “PM” indicator will be shown only when you select the 12 hour clock
display.
Note
The time settings will be reset if the unit is not powered for more than one
week.
Move the CLOCK switch on the rear panel to switch the clock type.
Clock display mode 1 (CLOCK 1)
Clock display mode 2 (CLOCK 2)
ADJUSTING THE CLOCK
Setting the time
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
2
Top panel
SET
Rear panel
Set time (flashing)
Switching the clock type
CLOCK 2
CLOCK 1
Rear panel
Eg: 10:50
Analog clock
hour hand
(hour)
Minute
Eg: 10:50
Minute
Hour
6 En
For details on compatible iPod models, refer to “SPECIFICATIONS” (P. 22).
1 Connect an iPod to the iPod dock.
2 Press SOURCE and set iPod as the playback
source.
3 Play the iPod by pressing / .
Playback can be controlled with either the remote control,
iPod or the top panel on this unit.
y
You can remove the iPod during playback.
If the system is turned off, it will turn on automatically when music/video
on the iPod is played.
If iPod is selected as the playback source, the system will automatically
turn off when 60 minutes have elapsed without a device being connected to
the iPod dock nor any operation performed.
The playback mode can be checked with the play/shuffle/repeat indicator on the front panel display.
Notes
Repeat/shuffle may not operate correctly depending on the type of iPod
used.
The repeat/shuffle playback order may differ depending on the type of
iPod used.
Repeat playback
Press REPEAT on the remote control to select a playback mode
from the following.
:One
:All
No display: Off
Shuffle playback
Press SHUFFLE on the remote control to select a playback mode
from the following.
: Songs
:Albums
No display: Off
LISTENING TO iPod
Playing the iPod
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
23
Top panel
Remote control
Button Function
Top
Panel
/
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
Remote
control
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
FOLDER/
MENU/
ENTER
iPod menu control
Repeat/shuffle playback
REPEAT
SHUFFLE
Remote control
7 En
English
1 Press SOURCE to set CD as the playback source.
2 Insert the audio CD into the Disc slot with the
label side facing toward the front of the unit.
Playback starts automatically. The track number is shown for a
while when starting playback or skipping tracks.
Use the following buttons to control the unit while playing
back tracks on audio CDs.
Note
CDs cannot be inserted or ejected when the system is in power save
mode ( P. 2).
LISTENING TO CD AND USB DEVICES
The unit will operate as follows when playing back tracks/files on CD/USB devices.
If the CD/USB device being played back is stopped, the track that was being played back will start playing from the beginning of the
track the next time playback begins.
If you press on the remote control while playback is stopped, the next time playback begins, the unit will play tracks as follows:
For audio CD : from the first track of the CD.
For data CD/USB device: from the first track of the folder that contains the track that was played last.
This system turns off automatically if no operation has been performed for 60 minutes after CD/USB device playback is stopped.
y
For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (P. 21).
Listening to an audio CD
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
12
Top panel
Button Function
Top
Panel
/
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
Eject the CD
Remote
control
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
Stop
CD
Track number
LISTENING TO CD AND USB DEVICES
8 En
1 Press SOURCE to set CD as the playback source.
2 Insert the data CD into the Disc slot with the
label side facing toward the front of the unit.
Playback starts automatically. The folder/file number is shown
for a while when starting playback or skipping tracks.
Use the following buttons to control the unit while playing
back tracks on data CDs.
Listening to a data CD
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
12
Top panel
Button Function
Top
Panel
/
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
PRESET Change the playback folder
Eject the CD
Remote
control
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
Stop
FOLDER Change the playback folder
Folder number
File number
9 En
LISTENING TO CD AND USB DEVICES
English
1 Press SOURCE and set USB as the playback
source.
2 Connect a USB device to the USB port.
Playback starts automatically. The folder/file number is shown
for a while
when starting playback or skipping tracks.
Use the following buttons to control the unit while playing
back tracks on USB devices.
y
Stop playback before removing the USB device.
The playback mode can be checked with the play/shuffle/repeat indicator on the front panel display.
y
If the selected source contains folders, each folder will be played in repeat/
shuffle mode.
Repeat playback
Press REPEAT on the remote control to select a playback mode
from the following.
:
All tracks within the folder (data CD/USB device only)
: All tracks
: 1 track
No display: Repeat mode off
Shuffle playback
Press SHUFFLE on the remote control to select a playback mode
from the following.
:
All tracks within the folder (data CD/USB device only)
: All tracks
No display: Shuffle mode off
Listening to a USB device
Note
When a USB device is connected, tracks are played back in the
following order:
Folder playback order:
folders are played in alphabetical order of the first 3 characters
of the folder name. Folder containing characters other than the
alphabet are played after alphabet character folders.
File playback order:
files will be played back in order from files with the oldest wrote
date.
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
21
Top panel
Button Function
Top
Panel
/
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
PRESET Change the playback folder
Remote
control
Play/Pause
/
Skip
Search backward/forward
(press and hold down)
Stop
FOLDER Change the playback folder
Folder number
File number
Repeat/shuffle playback
REPEAT
SHUFFLE
Remote control
10 En
This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth component (mobile phone, digital
audio player, etc.). Please also refer to the owner’s manual of your Bluetooth component.
Pairing is an operation that registers the communicating component (subsequently called “the other component”) with this unit. You’ll need
to perform the pairing operation the first time you use your Bluetooth component with this unit, or if the pairing settings have been deleted.
Once pairing has been completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected. If pairing is not
successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” (P. 20).
y
This unit can be paired with up to eight other components. When pairing with the ninth component has succeeded, pairing data for the component with the
oldest connection date will be deleted.
If this unit is connected via Bluetooth to another component, hold down SOURCE button on this unit or Bluetooth on the remote control to disconnect the
Bluetooth connection before you perform the pairing operation.
If using an iPod touch/iPhone/iPad
1 Press the SOURCE button to switch the playback
source to Bluetooth.
2 On your iPod touch/iPhone/iPad, turn [Settings]
[General] [Bluetooth] on.
The Bluetooth connection list will appear in [Devices].
(This procedure or display may differ depending on the type of
your iPod touch/iPhone/iPad.)
3 From the Bluetooth connection list of the other
component, choose this unit (ISX-B820 Yamaha).
When pairing has been completed, your iPod touch/iPhone/
iPad will indicate “Connected”.
The Bluetooth indicator on the front panel display of this unit
will light.
If using other than an iPod touch/iPhone/iPad
1 Press the SOURCE button to switch the playback
source to Bluetooth.
2 Perform Bluetooth pairing on the other component.
For details refer to the owner’s manual of the other
component.
3 From the Bluetooth connection list of the other
component, choose this unit (ISX-B820 Yamaha).
When pairing has been completed, the Bluetooth indicator on
the front panel display of this unit will light for about 1
second.
y
If you are asked to enter a password, enter the numerals “0000”.
LISTENING TO MUSIC FROM YOUR Bluetooth COMPONENT
Pairing this unit with your Bluetooth component
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
1
Top panel
Bluetooth indicator
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
1
Top panel
Bluetooth indicator
11 En
LISTENING TO MUSIC FROM YOUR Bluetooth COMPONENT
English
1 Press the SOURCE button to switch the playback
source to Bluetooth.
2 Connect this unit and your other component via
Bluetooth.
3
Play back music from your
Bluetooth
component.
Note
Take care that the volume setting of this unit is not too high. We
recommend that you adjust the volume on the other component.
y
If you connect via Bluetooth from your other component and play
back music while this unit is turned off the system, this unit will
automatically turn on the system.
If you disconnect the Bluetooth connection from your other
component while the playback source is set to Bluetooth, this unit
will automatically turn off the system.
•If Bluetooth is selected as the playback source, this unit will
automatically turn off the system when 60 minutes have elapsed
without any Bluetooth connection nor any operation performed.
Once pairing has been completed, connecting a Bluetooth will be easy the next time.
Connecting from this unit
1 Press the SOURCE button to switch the playback
source to Bluetooth.
The Bluetooth indicator will blink on the front panel display;
this unit will search for the other component that was most
recently connected via Bluetooth, and will then establish a
connection (You must first turn on the Bluetooth setting of the
other component).
When the Bluetooth connection has been established, the
Bluetooth indicator will light.
Note
Yamaha does not guarantee all connections between this unit and
Bluetooth component.
Connecting from the other component
1 In the Bluetooth settings of the other component, turn Bluetooth on.
2 From the Bluetooth connection list of the other component, choose this unit (ISX-B820 Yamaha).
The Bluetooth connection will be established, and the Bluetooth indicator on the front panel display of this unit will light.
Note
Bluetooth connections cannot be established from the other component when this unit is in power save mode. Turn the system on.
If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be disconnected.
Hold down SOURCE button on this unit or Bluetooth on the remote control.
Turn the system off.
Turn off the Bluetooth setting of the other component.
y
When you connect an iPod touch/iPhone/iPad via Bluetooth, the Bluetooth connection may be disconnected if you switch the playback source to iPod while
another iPod is connected to the iPod dock.
Listening to a Bluetooth component
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
1
Top panel
Connecting an already-paired component via Bluetooth
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
1
Top panel
Bluetooth indicator
Disconnecting a Bluetooth connection
12 En
Note
If you tune to an FM station manually, the sound will be in monaural.
1 Press SOURCE and set FM as the playback source.
2 Press / to tune the FM station.
Use the preset function to store your favorite 5 stations.
1 Press / to tune into your favorite FM station.
2 Press and hold down PRESET.
3 Press PRESET and select the preset number to
store the FM station.
4 Press and hold down PRESET to store the preset
station.
This stores the FM station.
LISTENING TO FM STATIONS
Selecting the FM station
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
12
Top panel
Tuning type Operation
Top
panel
Automatic
tuning
Press and hold down
or .
Manual
tuning
Press or repeatedly.
Remote
control
Automatic
tuning
Press and hold down
TUNING or .
Manual
tuning
Press TUNING or
repeatedly.
FM
Reception
frequency
Storing FM stations (preset)
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
234 1
Top panel
Using the remote control
Press and hold down MEMORY.
Using the remote control
Press PRESET /.
Using the remote control
Press MEMORY.
FM
Preset
number
13 En
LISTENING TO EXTERNAL SOURCES
English
1 Press SOURCE and set FM as the playback source.
2 Press PRESET repeatedly to select the preset FM
station.
Turn the system off before connecting audio cables. Remove the
terminal cover before connecting external devices.
1 Connect external audio device to AUX on the rear
panel using a commercially available 3.5 mm (1/8 in)
stereo mini plug cable.
Note
Turn down the volume of the unit and your external audio device before
connection.
2 Press to turn the system on.
3 Press SOURCE and set AUX as the playback
source.
4 Start playback on the connected external audio
device.
Selecting a preset FM station
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
1 2
Top panel
Using the remote control
Press PRESET /.
LISTENING TO EXTERNAL SOURCES
AUTO SET
DIMMER
CL
2
1
VOLUME
USB LAB
SOURCE ALARM SNOOZ
23
Top panel
AUX
75 Ω
FM ANT
AUX
14 En
The unit includes an alarm function (IntelliAlarm) that plays back music sources or set of beeps at the set time in a variety of different
methods. The alarm function has following features.
3 types of alarms
Select from 3 alarm types, combining music and beep sounds.
Various music sources
The iPod, audio CD, data CD, USB device and radio can be selected. The following can also be selected depending on the audio source:
* For information on creating a playlist, refer to the instructions for your iPod or iTunes.
Snooze
The snooze function can be enabled to replay the alarm after 5 minutes.
USING THE ALARM FUNCTION
SOURCE + BEEP
The selected audio source and beep sound are played at the set time. This mode is recommended for
the best possible start to the day.
3 minutes before the set time: the source music begins to fade in and the volume gradually increases
as the alarm time approaches.
Alarm time: a beeping sound also begins playing.
SOURCE
The selected audio source is played at the set time. The volume fades in gradually and increases to
the set volume.
BEEP Only beep sound is played back at the set time.
Source Playback method Function
iPod Resume
The unit resumes play from the last track you played.
If you’ve created a playlist* with the name “ALARM Yamaha DTA” in
advance, the playlist stored on the iPod can be played back
repeatedly.
When entering the playlist name, use single-byte spaces to separate
words, and enter single-byte characters, taking care that uppercase/
lowercase letters are used correctly.
Audio CD
Selected track The selected track is played repeatedly.
Resume The track you listened to last time is played back.
Data CD/USB
Folder The selected folder is played repeatedly.
Resume The track you listened to last time is played back.
FM
Preset station The selected preset FM station is played.
Resume The FM station you listened to last time is played back.
15 En
USING THE ALARM FUNCTION
English
Note
The alarm setting will be erased if the system is turned off without properly
completing it.
1 Press and hold ALARM.
The alarm indicator ( ) and set alarm time will flash
.
2 Press / to set the alarm time.
3 Select the alarm type with the ALARM TYPE
switch on the rear panel.
For details on alarm types, refer to P. 14.
4 (when alarm types other than BEEP are selected)
Press SOURCE to select music source.
Sources other than AUX and Bluetooth can be selected.
Notes
If iPod/CD/USB has been selected, connect/insert the audio source
(iPod, audio/data CD, USB device) to the unit.
If source cannot be played back at the time set for the alarm (eg. iPod
is not connected), the beep sound is played back.
5 (when alarm types other than BEEP are selected)
Specify the track, folder or FM station to be played.
If iPod is set as the source:
No settings required.
If CD/USB/FM is selected as the source:
Press PRESET to select the track (audio CD), folder (data
CD/USB devise) or FM station to be played.
y
When iPod is set as the source, the unit plays back the “ALARM
Yamaha DTA” playlist at the set alarm time. If this playlist cannot be
found within the iPod, the unit resumes play from the last track you
played (resume).
When CD/USB/FM is selected as the source and “0” is set, the
playback resumes from the track/FM station you listened to last time
(resume).
6 Set the alarm volume by pressing VOLUME –/+
.
7 Press ALARM to complete setting the alarm.
The alarm will be set, and the alarm indicator ( ) will
light up.
Set the alarm time and alarm type
Using the remote control
Press / .
Using the remote control
Press Source button to select music source.
AUTO SET BEEP
SOURCE
+
BEEP
SOURCE
DIMMER
CLOCK
ALARM TYPE
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE PRESETALARM SNOOZE
SLEEP
17
2465
Top panel
Alarm indicator
Alarm time
BEEP
SOURCE+
BEEP
SOURCE
Rear panel
Using the remote control
Press PRESET /.
Alarm volume
USING THE ALARM FUNCTION
16 En
1 Press ALARM.
When the alarm is on, the alarm indicator ( ) is shown,
and the alarm time is shown for a while. If you press ALARM
again, the alarm indicator ( ) and the alarm will turn off.
y
The alarm setting will be saved even if the alarm is turned off. If the
alarm is turned on again by pressing ALARM, the alarm will sound
with the previously alarm settings.
At the set time, the alarm sound is played back. During playback, the following operations are available.
1 (if you want to stop the alarm for a short time) Press
SNOOZE/SLEEP.
SNOOZE will stop the alarm and resume again in 5 minutes.
y
When SOURCE + BEEP is set, press SNOOZE/SLEEP once to
stop the beep sound, and twice to stop the audio source. 5 minutes
after the audio source is stopped, it will start fading in again and the
beep sound will resume.
The alarm indicator will flash when the snooze function is activated.
2 (if you want to turn the alarm off) Press ALARM or
.
y
The alarm stops automatically after 60 minutes unless you stop the
alarm.
Turning the alarm on/off
AUTO SET BEEP
SOUR
DIMMER
CLOCK
ALARM
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE ALARM SNOOZE
SLEEP
1
Top panel
Operations while playing back alarm sound
AUTO SET BEEP
SOUR
DIMMER
CLOCK
ALARM
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE ALARM SNOOZE
SLEEP
2
2
1
Top panel
17 En
English
You can set the time to turn off the system automatically.
1 Press SNOOZE/SLEEP a number of times to set
the time until the system turns off.
The sleep timer can be set to 30, 60, 90 and 120 minutes.
When the time is set, the sleep indicator ( ) is shown on the
front panel display.
y
If you press SNOOZE/SLEEP while the sleep timer is activated, the
sleep timer setting will be canceled.
1 Press one of the LOW/MID/HIGH EQ buttons on
the remote control while playing back.
Select the tone to be adjusted (LOW, MID, HIGH).
2 Press / to adjust the tone.
Each tone can be adjusted from –5 to +5.
3 Press ENTER to complete settings.
You can also press the EQ button that you pressed in Step 1
to complete the settings.
To change the tone of other frequency band, return to step 1
and press the EQ button to adjust the desired frequency.
1 Adjust the brightness with the DIMMER switch on
the rear panel.
AUTO: adjusts the brightness automatically to match the
surroundings.
1: brighter.
2: darker.
Note
When AUTO is set, the brightness of the front panel display is adjusted
automatically with the illumination sensor (P. 3). Ensure that the sensor
is not covered.
USING THE SLEEP TIMER
AUTO SET BEEP
SOURC
DIMMER
CLOCK
ALARM T
2
1
2
1
VOLUME
USB LABEL SIDE
SOURCE ALARM SNOOZE
SLEEP
1
Top panel
TONE CONTROL
1
2
3
Remote control
Tone
Setting
Tone
ADJUST BRIGHTNESS OF FRONT PANEL DISPLAY
AUTO21
Rear panel
18 En
If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested solutions or if the
problem is not listed below, turn off and unplug the system, and consult the nearest authorized Yamaha dealer or service center.
TROUBLESHOOTING
General
Problem Cause Solution
Can’t turn on the unit.
The power cable is not connect firmly. Reconnect the power cable into the wall outlet and
the unit firmly.
The speakers make no sound.
The volume may be set to the minimum level. Adjust the volume level.
The source may be incorrect. Select the correct source.
Sound suddenly turns off.
The sleep ( P. 17) may be set. Turn on the system and play the source again.
Sound is cracked/distorted or there is
abnormal noise.
Input source volume is excessive, or volume of this
unit is excessive (especially Bass).
Adjust volume with VOLUME, or adjust Bass with
EQ ( P. 17 ).
The unit does not operate properly.
The unit may have received a strong electrical
shock such as lightning or excessive static
electricity, or power supply may have dropped.
Turn the system off, and disconnect the power
cable. Wait about 30 seconds, reconnect the power
cable, and turn the system on.
The system turns on but immediately
shuts off.
A digital or high-frequency equipment
produces noises.
The unit may be placed too close to the digital or
high-frequency equipment.
Place the unit further away from the equipment.
The clock setting has been cleared.
The unit is left more than one week after you
disconnect the power cable from the wall outlet.
Plug the power cable into the wall outlet firmly, and
set the clock again ( P. 5).
iPod does not play back at the alarm time
even if SOURCE is set to iPod.
The iPod is not connect in the iPod dock firmly. Remove an iPod from the unit, and then connect it
in the iPod dock again ( P. 2).
ALARM TYPE switch is set to BEEP. Set ALARM TYPE to SOURCE + BEEP or
SOURCE ( P. 15).
Clock flashes and the unit cannot be
operated.
CLOCK switch on the rear panel is set to SET, and
this unit is in clock setting mode.
Set CLOCK switch to CLOCK1 or CLOCK2
( P. 5).
iPod
Problem Cause Solution
No sound.
The iPod is not connect in the iPod dock firmly. Remove an iPod from the unit, and then connect it
in the iPod dock again ( P. 2).
The iPod software version has not been updated. Download the latest iTunes version from the Apple
website, and update the iPod software to the latest
version.
The iPod does not charge up.
The iPod is not connect in the iPod dock firmly. Remove an iPod from the unit, and then connect it
in the iPod dock again ( P. 2).
The system is set to power save mode ( P. 2).
Press to cancel the power save mode.
The iPod indicator flashes twice, and
repeated 3 times, after connecting the
iPod.
The iPod being used is not supported by the unit. Use a supported iPod ( P. 22).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196

Yamaha ISX-B820 Manual de utilizare

Categorie
CD playere
Tip
Manual de utilizare